Answer:0.00125 watts
Explanation:
resistance=50 ohms
Current=5 milliamps
Current=5/1000 amps
Current=0.005 amps
Power=(current)^2 x (resistance)
Power=(0.005)^2 x 50
Power=0.000025 x 50
Power=0.00125 watts
Answer:
if a circuit is powered by 100v and has an overall resistance of 50 ohms 2 amps flows through the circuit
Explanation:
Match these items.
1 . pls help
asteroids
between Mars and Jupiter
2 .
fission
ice, dust, frozen gases
3 .
energy
sun's atmosphere
4 .
fusion
ability to do work
5 .
corona
splitting atoms
6 .
comets
the combining of atomic nuclei to form one nucleus
Answer:
Here's your answer :
Asteroids - Between mars and JupiterFission - splitting atomsEnergy - Sun's atmosphereFusion - The combining of atomic nuclei to form one nucleusCorona - Ability to do workComets - Ice, dust, frozen gaseshope it helps!
19
Which gas is the most abundant greenhouse gas?
A.
ozone
B.
chlorofluorocarbon
C.
carbon dioxide
OD.
methane
E.
water vapor
Reset
Next
Carbon dioxide is the most abundant greenhouse gas in the atmosphere.
Answer:C
Explanation:
Carbon dioxide is the most abundance greenhouse gas in The atmosphere.
An astronaut is being tested in a centrifuge. The centrifuge has a radius of 11.0 m and, in starting, rotates according to θ = 0.260t2, where t is in seconds and θ is in radians. When t = 2.40 s, what are the magnitudes of the astronaut's (a) angular velocity, (b) linear velocity, (c) tangential acceleration, and (d) radial acceleration?
Answer:
a) 1.248 rad/s
b) 13.728 m/s
c) 0.52 rad/s^2
d) 17.132m/s^2
Explanation:
You have that the angles described by a astronaut is given by:
[tex]\theta=0.260t^2[/tex]
(a) To find the angular velocity of the astronaut you use the derivative og the angle respect to time:
[tex]\omega=\frac{d\theta}{dt}=\frac{d}{dt}[0.260t^2]=0.52t[/tex]
Then, you evaluate for t=2.40 s:
[tex]\omega=0.52(2.40)=1.248\frac{rad}{s}[/tex]
(b) The linear velocity is calculated by using the following formula:
[tex]v=\omega r[/tex]
r: radius if the trajectory of the astronaut = 11.0m
You replace r and w and obtain:
[tex]v=(1.248\frac{rad}{s})(11.0m)=13.728\frac{m}{s}[/tex]
(c) The tangential acceleration is:
[tex]a_T=\alpha r\\\\\alpha=\frac{\omega^2}{2\theta}=\frac{(1.248rad/s)^2}{2(0.260(2.40s)^2)}=0.52\frac{rad}{s^2}[/tex]
(d) The radial acceleration is:
[tex]a_r=\frac{v^2}{r}=\frac{(13.728m/s)^2}{11.0m}=17.132\frac{m}{s^2}[/tex]
The current in the wires of a circuit is 60 milliamps. If the resistance of the circuit were doubled (with no change in voltage), then it’s new current would be _____ milliamps
Answer:30
Explanation:
Current=60 milliamps
Current=(voltage)/(resistance)
60=(voltage)/(resistance)
Doubling the resistance means multiplying both sides by 1/2
60x1/2=(voltage)/(resistance) x 1/2
30=(voltage)/2(resistance)
Therefore the resistance would be 30 milliamp if we double the resistance
Coulomb's law for the magnitude of the force FFF between two particles with charges QQQ and Q′Q′Q^\prime separated by a distance ddd is
|F|=K|QQ′|d2|F|=K|QQ′|d2,
where K=14πϵ0K=14πϵ0, and ϵ0=8.854×10−12C2/(N⋅m2)ϵ0=8.854×10−12C2/(N⋅m2) is the permittivity of free space.
Consider two point charges located on the x axis: one charge, q1q1q_1 = -15.0 nCnC , is located at x1x1x_1 = -1.660 mm ; the second charge, q2q2q_2 = 34.5 nCnC , is at the origin (x=0.0000)(x=0.0000).
What is the net force exerted by these two charges on a third charge q3q3q_3 = 47.0 nCnC placed between q1q1q_1 and q2q2q_2 at x3x3x_3 = -1.240 mm ?
Your answer may be positive or negative, depending on the direction of the force.
Answer:
Explanation:
Force between two charges of q₁ and q₂ at distance d is given by the expression
F = k q₁ q₂ / d₂
Here force between charge q₁ = - 15 x 10⁻⁹ C and q₃ = 47 x 10⁻⁹ C when distance between them d = (1.66 - 1.24 ) = .42 mm
k = 1/ 4π x 8.85 x 10⁻¹²
putting the values in the expression
F = 1/ 4π x 8.85 x 10⁻¹² x - 15 x 10⁻⁹ x 47 x 10⁻⁹ /( .42 x 10⁻³)²
= 9 x 10⁹ x - 15 x 10⁻⁹ x 47 x 10⁻⁹ /( .42 x 10⁻³)²
= 35969.4 x 10⁻³ N .
force between charge q₂ = 34.5 x 10⁻⁹ C and q₃ = 47 x 10⁻⁹ C when distance between them d = ( 1.24 - 0 ) = 1.24 mm .
putting the values in the expression
F = 1/ 4π x 8.85 x 10⁻¹² x 34.5 x 10⁻⁹ x 47 x 10⁻⁹ /( .42 x 10⁻³)²
= 9 x 10⁹ x - 34.5 x 10⁻⁹ x 47 x 10⁻⁹ /( .42 x 10⁻³)²
= 82729.6 x 10⁻³ N
Both these forces will act in the same direction towards the left (away from the origin towards - ve x axis)
Total force = 118699 x 10⁻³
= 118.7 N.
A 25kg box in released on a 27° incline and accelerates down the incline at 0.3 m/s2. Find the friction force impending its motion? What is the coefficient of kinetic friction?
A block is given an initial speed of 3m/s up a 25° incline. Coefficient of friction
Answer:
a) μ = 0.475 , b) μ = 0.433
Explanation:
a) For this exercise of Newton's second law, we create a reference system with the x-axis parallel to the plane and the y-axis perpendicular to it
X axis
Wₓ - fr = m a
the friction force has the expression
fr = μ N
y Axis
N - [tex]W_{y}[/tex] = 0
let's use trigonometry for the components the weight
sin 27 = Wₓ / W
Wₓ = W sin 27
cos 27 = W_{y} / W
W_{y} = W cos 27
N = W cos 27
W sin 27 - μ W cos 27 = m a
mg sin 27 - μ mg cos 27 = m a
μ = (g sin 27 - a) / (g cos 27)
very = tan 27 - a / g sec 27
μ = 0.510 - 0.0344
μ = 0.475
b) now the block starts with an initial speed of 3m / s. In Newton's second law velocity does not appear, so this term does not affect the result, the change in slope does affect the result
μ = tan 25 - 0.3 / 9.8 sec 25
μ = 0.466 -0.03378
μ = 0.433
Pendulum clock. Your friend is trying to construct a clock for a craft show and asks you for some advice. She has decided to construct the clock with a pendulum. The pendulum will be a very thin, very light wooden bar with a thin, but heavy, brass ring fastened to one end. The length of the rod is 80 cm and the diameter of the ring is 10 cm. She is planning to drill a hole in the bar to place the axis of rotation 15 cm from one end. She wants you to tell her the period of this pendulum.
Answer:
The time period for this pendulum is 1.68 seconds
Explanation:
Solution
Given that:
The length of the pendulum is measured from the axis of rotation to the center of mass of the bob of the pendulum
Now,
In this case, the length becomes:
L= 80 - 15+5
L = 70 cm
The time period = T = 2π √L/g
T = 2* 3.14 *√0.7/9.8
= 1.68 seconds
Note: Kindly find an attached work to the part of the solution of the given question
Distributions of electric charges in a cell play a role in moving ions into and out of a cell. In this situation, the motion of the ion is affected by two forces: the electric force due to the non-uniform charge distribution in the cell membrane, and the resistive force (viscosity) due to colliding with the fluid molecules. In order to begin our analysis of this, let's consider a toy model in which the ion is moving in response to electric forces alone.
Charges in a cell membrane are distributed along the opposite sides of the membrane approximately uniformly. This leads to an (on the average) constant electric field inside the membrane. A simple model that gives this kind of field is two large parallel plates close together. The field between the plates is approximately constant pointing from the negative to the parallel plate. This results in a charge feeling a constant force anywhere between the plates (sort of like flat-earth gravity turned sideways). Outside of the plates the electric fields from the two plates cancel and there is no force.
2. The electric field between the plates (inside the membrane) is about 107 N/C and the thickness of the membrane is about 7 nm. Estimate:
2.1 The electric force on the ion when it is in the center of the channel.
F = N
Explain your reasoning.
2.2 The acceleration of the ion when it is in the center of the channel.
a = nm/s2
Explain your reasoning.
2.3 The magnitude of the change in the ion's potential energy as it crosses from one side of the plates to the other.
U = J
Explain your reasoning.
2.4 The kinetic energy the ion would gain as it crosses from one side of the plates to the other.
KE = J
Explain your reasoning.
Could you explain 2.3!
Answer:
An atom is the smallest constituent unit of ordinary matter that constitutes a chemical element. Every solid, liquid, gas, and plasma is composed of neutral or ionized atoms. Atoms are extremely small; typical sizes are around 100 picometers.Explanation:
An atom is the smallest constituent unit of ordinary matter that constitutes a chemical element.
What is atom?Every solid, liquid, gas, and plasma is composed of neutral or ionized atoms. Atoms are extremely small; typical sizes are around 100 picometers.
Each atom is made up of a nucleus and one or more electrons that are linked to it. One or more protons and a significant number of neutrons make up the nucleus. Only the most prevalent type of hydrogen is neutron-free.
Atoms that are neutral or ionized make up every solid, liquid, gas, and form of plasma. Atoms are incredibly tiny, measuring typically 100 picometers across. The nucleus of an atom contains more than 99.94% of its mass.
Therefore, An atom is the smallest constituent unit of ordinary matter that constitutes a chemical element.
To learn more about atom, refer to the link:
https://brainly.com/question/1566330
#SPJ2
a) When we were examining the Electromagnetic Tab, we saw that a flow of electrons or a current as we say it, creates a magnetic field. What about the converse, can a magnetic field be involved in the creation of a flow of electrons/current? Therefore is it reasonable to suggest that we can create a magnetic field by having a flow of current and this can be used to make more current? Explain how this can occur
Answer:
Magnetic field can be used to produce current, infact a changing magnetic field can produce current.
A changing magnetic field in a loop causes the flux linked with the loop to change in turn generating a emf in the loop and therefore a current.
For a loop of area A and resistance R.
I =dPhi/dt/R
В. А
I = AcosФ/R .dB /dt
But it isn't reasonable to say that we can create a magnetic field by having a flow of current and this can be used to make more current because the current generated due to change in magnetic field created by increase/decrease in flow of current will be in a direction such that it will counter act the change in magnetic field caused by increase/decrease in current flow.(lenz's law).
We were unable to transcribe this image
Ф= В. А
I = Acos dB Rd
The figure shows a crane whose weight is 12.5 kN and center of gravity in G. (a) If the crane needs to suspend the 2.5kN drum, determine the reactions on the wheel in A and B when the boom is in the position shown.(b) Considering the same situation illustrated, what is the value of the maximum weight that the crane can suspend without tipping over?
Answer:
(a) Ra = 9.25 kN; Rb = 5.75 kN
(b) 26.7 kN
Explanation:
(a) Draw a free-body diagram of the crane. There are four forces:
Reaction Ra pushing up at A,
Reaction Rb pushing up at B,
Weight force 12.5 kN pulling down at G,
and weight force 2.5 kN pulling down at F.
Sum of moments about B in the counterclockwise direction:
∑τ = Iα
-Ra (0.66 m + 0.42 m + 2.52 m) + 12.5 kN (2.52 m + 0.42 m) − 2.5 kN ((3.6 m + 0.9 m) cos 30° − 2.52 m) = 0
-Ra (3.6 m) + 12.5 kN (2.94 m) − 2.5 kN (1.38 m) = 0
Ra = 9.25 kN
Sum of moments about A in the counterclockwise direction:
∑τ = Iα
Rb (0.66 m + 0.42 m + 2.52 m) − 12.5 kN (0.66 m) − 2.5 kN ((3.6 m + 0.9 m) cos 30° + 0.66 m + 0.42 m) = 0
Rb (3.6 m) − 12.5 kN (0.66 m) − 2.5 kN (4.98 m) = 0
Rb = 5.75 kN
Alternatively, you can use sum of the forces in the y direction as your second equation.
∑F = ma
Ra + Rb − 12.5 kN − 2.5 kN = 0
Ra + Rb = 15 kN
9.25 kN + Rb = 15 kN
Rb = 5.75 kN
However, you must be careful. If you make a mistake in the first equation, it will carry over to this equation.
(b) At the maximum weight, Ra = 0.
Sum of the moments about B in the counterclockwise direction:
∑τ = Iα
12.5 kN (2.52 m + 0.42 m) − F ((3.6 m + 0.9 m) cos 30° − 2.52 m) = 0
12.5 kN (2.94 m) − F (1.38 m) = 0
F = 26.7 kN
Which of the following statements are true? a. Kinematics is the science that studies forces and motion of particles and bodies. b. Speed is a vector quantity. c. The units of velocity are length divided by time. d. The term deceleration is commonly used to describe a negative acceleration.
Answer:
true. b, c and d
Explanation:
Let's review each statement separately
a) False. The kinematics studies the position, speed and acceleration of the bodies, but not what causes these changes
b) True. Velocity is the displacement between time, displacement is a vector, and time is a scalar, so the division between them gives a vector
c) True. speed is the displacement that is a length between time, so its unit is length / time
d) true desaceleration = - aceleration
A small object begins a free-fall from a height of =81.5 m at 0=0 s . After τ=2.20 s , a second small object is launched vertically up from the ground with an initial velocity of 0=40.0 m/s . At what height from the ground will the two objects first meet?
Answer:
33.2 m
Explanation:
For the first object:
y₀ = 81.5 m
v₀ = 0 m/s
a = -9.8 m/s²
t₀ = 0 s
y = y₀ + v₀ t + ½ at²
y = 81.5 − 4.9t²
For the second object:
y₀ = 0 m
v₀ = 40.0 m/s
a = -9.8 m/s²
t₀ = 2.20 s
y = y₀ + v₀ t + ½ at²
y = 40(t−2.2) − 4.9(t−2.2)²
When they meet:
81.5 − 4.9t² = 40(t−2.2) − 4.9(t−2.2)²
81.5 − 4.9t² = 40t − 88 − 4.9 (t² − 4.4t + 4.84)
81.5 − 4.9t² = 40t − 88 − 4.9t² + 21.56t − 23.716
81.5 = 61.56t − 111.716
193.216 = 61.56t
t = 3.139
The position at that time is:
y = 81.5 − 4.9(3.139)²
y = 33.2
An ideal spring is fixed at one end. A variable force F pulls on the spring. When the magnitude of F reaches a value of 30.8 N, the spring is stretched by 17.7 cm from its equilibrium length. Calculate the additional work required by F to stretch the spring by an additional 12.4 cm from that position.
Answer:
[tex]W=5.16 J[/tex]
Explanation:
Using the Hooke's law we can find the elasticity constant:
[tex]F=-k\Delta x[/tex]
[tex]30.8=-k*0.177[/tex]
[tex]k=|-\frac{30.8}{0.177}|[/tex]
[tex]k=174 N/m[/tex]
Now, we know that the work done is equal to the elastic energy, so we will have:
[tex]W=\frac{1}{2}k(x_{2}^{2}-x_{1}^{2})[/tex]
x2 is the final distance (x2 = 0.177+0.124 = 0.301 m)
x1 is the initial distance (x1 = 0.177 m)
[tex]W=\frac{1}{2}*174(0.301^{2}-0.177^{2})[/tex]
[tex]W=5.16 J[/tex]
I hope it helps you!
A cube, 1 m on each edge, is held 0.75 m below the surface of a pool of water by a rope. The mass of the cube is 700 kg, and the weight distribution is such that one face remains parallel to the surface of the water. a. Find the tension in the rope. b. Assuming the rope is cut, how far will the cube protrude from the water
Answer:
Explanation:
The mass of cube = 700 kg
volume = 1 m³
density = 700 kg / m²
Its density is less than that of water so it will try to float on the surface .
Tension in rope will be equal to net upward force
upthrust = volume x density of water x g
= 1 x 10³ x 9.8
= 9800 N
weight of cube = mass x g
= 700 x 9.8
= 6860 N .
Net upward force = 9800 - 6860
= 2940 N.
Tension in the rope = 2940 N.
Rope will hold the cube inside and not allow it to go outside water .
b )
If rope is cut , cube being lighter , will float on surface of water .
Part of cube inside water while floating
= 6860 / 9800
= .7
.7 m will remain inside water
part floating outside
= 1 - 0.7
= 0.3 m .
I need help plz help me out 10 points!!!!!!!
Answer:
The answer is diffraction
Explanation:
Answer:
The answer is diffraction
Explanation:
I did the test! HOPE THIS HELPS!
Official (Closed) - Non Sensitive
MEF Tutorial 2 Q3
A train with a maximum speed of 29.17 m/s has an
acceleration rate of 0.25 m/s2 and a deceleration
rate of 0.7 m/s2. Determine the minimum running
time, if it starts from rest at one station and stops
at the next station 7 km away.
Answer:
The minimum running time is 319.47 s.
Explanation:
First we find the distance covered and time taken by the train to reach its maximum speed:
We have:
Initial Speed = Vi = 0 m/s (Since, train is initially at rest)
Final Speed = Vf = 29.17 m/s
Acceleration = a = 0.25 m/s²
Distance Covered to reach maximum speed = s₁
Time taken to reach maximum speed = t₁
Using 1st equation of motion:
Vf = Vi + at₁
t₁ = (Vf - Vi)/a
t₁ = (29.17 m/s - 0 m/s)/(0.25 m/s²)
t₁ = 116.68 s
Using 2nd equation of motion:
s₁ = (Vi)(t₁) + (0.5)(a)(t₁)²
s₁ = (0 m/s)(116.68 s) + (0.5)(0.25 m/s²)(116.68 s)²
s₁ = 1701.78 m = 1.7 km
Now, we shall calculate the end time and distance covered by train, when it comes to rest on next station.
We have:
Final Speed = Vf = 0 m/s (Since, train is finally stops)
Initial Speed = Vi = 29.17 m/s (The train must maintain max. speed for min time)
Deceleration = a = - 0.7 m/s²
Distance Covered to stop = s₂
Time taken to stop = t₂
Using 1st equation of motion:
Vf = Vi + at₂
t₂ = (Vf - Vi)/a
t₂ = (0 m/s - 29.17 m/s)/(- 0.7 m/s²)
t₂ = 41.67 s
Using 2nd equation of motion:
s₂ = (Vi)(t₂) + (0.5)(a)(t₂)²
s₂ = (29.17 m/s)(41.67 s) + (0.5)(- 0.7 m/s²)(41.67 s)²
s₂ = 607.78 m = 0.6 km
Since, we know that the rest of 7 km, the train must maintain the maximum speed to get to the next station in minimum time.
The remaining distance is:
s₃ = 7 km - s₂ - s₁
s₃ = 7 km - 0.6 km - 1.7 km
s₃ = 4.7 km
Now, for uniform speed we use the relation:
s₃ = vt₃
t₃ = s₃/v
t₃ = (4700 m)/(29.17 m/s)
t₃ = 161.12 s
So, the minimum running time will be:
t = t₁ + t₂ + t₃
t = 116.68 s + 41.67 s + 161.12 s
t = 319.47 s
Photons of light scatter off molecules, and the distance you can see through a gas is proportional to the mean free path of photons through the gas. Photons are not gas molecules, so the mean free path of a photon is not equal to that of a molecule, but its dependence on the number density of the gas and on molecular radius is the same. Suppose you are in a smoggy city and can barely see buildings 500 m away.
(a) How far would you be able to see if all the molecules around you suddenly doubled in volume?
(b) How far would you be able to see if the temperature suddenly rose from 20◦C to a blazing hot 1500◦C with the pressure unchanged?
Answer:
a) 315 m
b) 3025.6 m
Explanation:
The picture attached shows the full explanation for the problem.
Which of the following is not true about of the use of MRI in medicine?
1) It produces no negative side-effects on the human body
2) It produces high resolution images of soft tissues
3) It is very cheap
4) It requires very strong magnetic fields
Answer:
3) False. It is expensive since it requires sophisticated equipment and very low temperatures
Explanation:
Nuclear magnetic resonance imaging measurements consist of magnetic resonance imaging to analyze tissues by the transition of the unpaired electron at carbon 13, giving information on the structure and composition of tissues. This information is processed in computers and transformed into images.
So the physical measurement is the MRN
Now we can analyze the statements in the problem
1) True by itself a magnetic measurement is non-invasive
2) True. Measuring carbon transitions has information about the soft tissue of the body
3) False. It is expensive since it requires sophisticated equipment and very low temperatures
4) Right. The applied magnetic field is high to be able to induce carbon transaction
Under electrostatic conditions, the electric field just outside the surface of any charged conductor
A. is always zero because the electric field is zero inside conductors
B. can have non zero components perpendicular to and parallel to the surface of the conductor
C. is always perpendicular to the surface of the conductor
D. is always parallel to the surface
E. is perpendicular to the surface of the conductor only if it is a sphere, a cylinder, or a flat sheet.
Answer:
C. is always perpendicular to the surface of the conductor
Explanation:
On a charged conductor , electric charge is uniformly distributed on its surface . The lines of forces are also uniformly distributed on all directions . They repel each other so they emerge perpendicular to the surface so that they do nor cut each other and at the same time they remain at maximum distance from each other.
(10 points) A spring with a 7-kg mass and a damping constant 12 can be held stretched 1 meters beyond its natural length by a force of 4 newtons. Suppose the spring is stretched 2 meters beyond its natural length and then released with zero velocity. In the notation of the text, what is the value c2−4mk? m2kg2/sec2 Find the position of the mass, in meters, after t seconds. Your answer should be a function of the variable t of the form c1eαt+c2eβt where α= (the larger of the two) β=
Answer:
......................
Which term defines the distance from crest to crest
Answer:
The horizontal distance between two adjacent crests or troughs is known as the wavelength.
Answer: Wavelength
Explanation:
From crest to crest, it is one full wavelength
in the figure calculates the acceleration of the block friction not today
Answer:
A fan pushes hot air out of a vent and into a room. The hot air displaces cold air in the room, causing the cold air to move closer to the floor.
The hot air displacing the cold air is an example of transfer by
Explanation:
also the answer is hit my dm on ig
Electric motors convert electrical energy to mechanical energy. When the current-carrying coil is placed between the magnetic poles, a force acts on it that causes it to rotate. The image below shows a simple electric motor. The motor is used to lift metal boxes. How can the motor be changed to be able to lift a heavier box? A. rotate the coil in a counter-clockwise direction B. add more loops of wire between the magnets C. change the polarity of the magnet D. decrease the size of the magnets
Answer:
B. add more loops of wire between the magnets
Explanation:
this would increase the magnetic force acting on the rod therefore increasing
By adding more loops of wire between the magnets the motor is changed to be able to lift a heavier box.
What is an electric motor?An electric motor is a mechanism that turns electricity into mechanical energy.
The interaction between the motor's magnetic field and electric current in a wire winding generates force in the form of torque imparted to the motor's shaft in most electric motors.
An electric generator is physically equivalent to an electric motor, but it converts mechanical energy into electrical energy using a reversed flow of power.
The load capacity in the motor can be increased by increasing the no of loops. So by adding more loops of wire between the magnets the motor is changed to be able to lift a heavier box.
Hence option B is correct.
To learn more about the electric motor refer to the link;
https://brainly.com/question/15409160
Minority group
A shared identity based on
cultural elements such as
heritage, language, and
religion
Ethnicity
A socially constructed
group of people who share
physical characteristics
that are considered
significant by a society
and that are used to
distinguish them from
other groups
Majority group
People who are singled
out for unequal treatment
and who regard
themselves as objects of
collective discrimination
Race
A group's subset that
consists of more than half
of the entire group's
members
Answer:
Minority group - People who are singled out for unequal treatment and who regard themselves as objects of collective discrimination.
Ethnicity - A shared identity based on cultural elements such as heritage, language, and religion.
Majority group - A group's subset that consists of more than half of the entire group's members.
Race - A socially constructed group of people who share physical characteristics that are considered significant by a society and that are used to distinguish them from other groups.
Explanation:
To better understand the above-mentioned definitions we would use some examples:
Elder people can be considered as a minority group in the United States because of their reduced status as a consequence of popular discrimination and prejudice against them. In contrast to them, young men consisting of more than half the population in the age category is an example of the majority group.
Groups of people like Hispanic Americans, Jews, Italian America, Irish are some examples of people belonging to different ethnic backgrounds residing in the U.S.
African Americans who are distinguished based on their skin color is an example of race.
Two forces are applied on a body. One produces a force of 480-N directly forward while the other gives a 513-N force at 32.4-degrees above the forward direction .Find the magnitude and direction(relative to forward direction of the resultant force that these forces exert on the body)
Answer:
F = (913.14 , 274.87 )
|F| = 953.61 direction 16.71°
Explanation:
To calculate the resultant force you take into account both x and y component of the implied forces:
[tex]\Sigma F_x=480N+513Ncos(32.4\°)=913.14N\\\\\Sigma F_y=513sin(32.4\°)=274.87N[/tex]
Thus, the net force over the body is:
[tex]F=(913.14N)\hat{i}+(274.87N)\hat{j}[/tex]
Next, you calculate the magnitude of the force:
[tex]F=\sqrt{(913.14N)+(274.87N)^2}=953.61N[/tex]
and the direction is:
[tex]\theta=tan^{-1}(\frac{274.14N}{913.14N})=16.71\°[/tex]
Which of these parameters is directly related to sound frequency?
Answer:Velocity
Explanation:
Velocity is directly proportional to the frequency of a wave.
Velocity=frequency x wavelength
Q1. What is the frequency of rotation of 1000 loop coil of area 20cm2 in a magnetic field of 5T to
generate an emf that has a maximum value of 15.7V?
Answer:
Explanation:
Emf e generated in a coil with no of turn n and area A rotating in a magnetic field B with angular speed of ω is given by the expression
e = e₀ sinωt
where e₀ = nωAB which is the maximum emf generated
Putting the given values
15.7 = 1000xω x 20 x 10⁻² x 5
ω = .0157
frequency of rotation
= ω / 2π
= .0157 / 2 x 3.14
= .0025 /s
9 rotation / hour .
In a shipping company distribution center, an open cart of mass 50 kg is rolling to the left at a speed of 5 m/s. You can ignore friction between the cart and the floor. A 15 kg package slides down a chute that makes an angle of 27 degrees below the horizontal. The package leaves the chute with a speed of 3 m/s, and lands in the cart after falling for 0.75 seconds. The package comes to a stop in the cart after 4 seconds. What is:a) the speed of the package just before it lands in the cart
Answer:
Explanation:
The package leaves the chute with a speed of 3 m/s, and lands in the cart after falling for 0.75 seconds . During .75 second duration . package undergoes free fall due to which additional vertical velocity is added
velocity added = a x t
= 9.8 x .75
= 7.35 m /s
Total vertical velocity
= 3 sin27 + 7.35
= 8.71 m /s
Horizontal component = 3 cos 27
= 2.67 m /s
If v be the resultant velocity of these components
v² = 2.67² + 8.71²
v² = 7.13 + 75.86
v = 9.11 m /s .
The uniform slender bar of mass m and length l is released from rest in the vertical position and pivots on its square end about the corner at O. (a) If the bar is observed to slip when 30 , find the coefficient of static friction s between the bar and the corner. (b)If the end of the bar is notched so that it cannot slip, find the angle at which contact between the bar and the corner ceases.
Answer:
A) 0.188
B) 53.1 ⁰
Explanation:
taking moment about 0
∑ Mo = Lo∝
mg 1/2 sin∅ = 1/3 m L^2∝
note ∝ = w[tex]\frac{dw}{d}[/tex]∅
forces acting along t-direction ( ASSUMED t direction)
∑ Ft = Ma(t) = mr∝
mg sin ∅ - F = m* 1/2 * 3g/2l sin∅
therefore F = mg/4 sin∅
forces acting along n - direction ( ASSUMED n direction)
∑ Fn = ma(n) = mr([tex]w^{2}[/tex])
= mg cos∅ - N = m*1/2*3g/1 ( 1 - cos∅ )
hence N = mg/2 ( 5cos∅ -3 )
A ) Angle given = 30⁰c find coefficient of static friction
∪ = F/N
= [tex]\frac{\frac{mg}{4}sin30 }{\frac{mg}{2}(5cos30 -3) }[/tex] = 0.188
B) when there is no slip
N = O
= 5 cos ∅ -3 =0
therefore cos ∅ = 3/5 hence ∅ = 53.1⁰
A person jumps out a fourth-story window 14 m above a firefighter safety net. The survivor stretches the net 1.8 m before coming to rest. what was the deceleration experienced by the survivor? Use g = 9.8 m/s2 Calculate to one decimal.
Answer:
The deceleration is [tex]a = - 76.27 m/s^2[/tex]
Explanation:
From the question we are told that
The height above firefighter safety net is [tex]H = 14 \ m[/tex]
The length by which the net is stretched is [tex]s = 1.8 \ m[/tex]
From the law of energy conservation
[tex]KE_T + PE_T = KE_B + PE_B[/tex]
Where [tex]KE_T[/tex] is the kinetic energy of the person before jumping which equal to zero(because to kinetic energy at maximum height )
and [tex]PE_T[/tex] is the potential energy of the before jumping which is mathematically represented at
[tex]PE_T = mg H[/tex]
and [tex]KE_B[/tex] is the kinetic energy of the person just before landing on the safety net which is mathematically represented at
[tex]KE_B = \frac{1}{2} m v^2[/tex]
and [tex]PE_B[/tex] is the potential energy of the person as he lands on the safety net which has a value of zero (because it is converted to kinetic energy )
So the above equation becomes
[tex]mgH = \frac{1}{2} m v^2[/tex]
=> [tex]v = \sqrt{2 gH }[/tex]
substituting values
[tex]v = 16.57 m/s[/tex]
Applying the equation o motion
[tex]v_f = v + 2 a s[/tex]
Now the final velocity is zero because the person comes to rest
So
[tex]0 = 16.57 + 2 * a * 1.8[/tex]
[tex]a = - \frac{16.57^2 }{2 * 1.8}[/tex]
[tex]a = - 76.27 m/s^2[/tex]
