A ball is thrown from the ground so that it’s initial vertical and horizontal components of velocity are 40m/s and 20m/s respectively. Find the ball’s total time of flight and distance it traverses before hitting the ground.

Answer:

12.2 m

Explanation:

Given:

v₀ = 15.6 m/s

v = 0 m/s

a = -10 m/s²

Find: Δy

v² = v₀² + 2aΔy

(0 m/s)² = (15.6 m/s)² + 2 (-10 m/s²) Δy

Δy = 12.2 m

[tex] \LARGE{ \boxed{ \rm{ \green{Answer:}}}}[/tex]

Given,

Finding the initial kinetic energy,

[tex]\large{ \boxed{ \rm{K.E. = \frac{1}{2}m {v}^{2}}}}[/tex]

⇛ KE = (1/2)mv²

⇛ KE = (1/2)(0.042)(15.6)²

⇛ KE = 5.11 J

|| ⚡By conservation of energy, the potential energy at the highest point will also be 5.11 J, since there is no kinetic energy at the highest point because the ball is not moving (we neglect energy lost due to air resistance, heat, sound, etc.) ⚡||

So, we have:

[tex] \large{ \boxed{ \rm{P.E. = mgh}}}[/tex]

⇛ h = PE/(mg)

⇛ h = 5.11 J /(0.042 × 9.8)

⇛ h = 12.41 m

✏The ball will rise upto a height of 12.41 m

━━━━━━━━━━━━━━━━━━━━

Answer:

The frictional force the road applies to the rear tire is static friction and it acts opposite to the direction in which the car is traveling.

Explanation:

This question suggests that the car is accelerating forward. Thus, the easiest way for us to know what friction is doing is for us to know what happens when we turn friction off.

Now, if there is no friction and the car is stopped, if we push down on the accelerator, it will make the front wheels to spin in a clockwise manner. This spin occurs on the frictionless surface with the rear wheels doing nothing while the car doesn't move.

Now, if we apply friction to just the front wheels, the car will accelerate forward while the back wheels would be dragging along the road and not be spinning. Thus, friction opposes the motion and as such, it must act im a direction opposite to where the car is going. This must be static friction.

The frictional force the road applies to the rear tire is static friction and it acts opposite to the direction in which the car is traveling.

Answer:

Explanation:

The moment of inertia of the disk I  = 1/2 m R² where R is radius of the disc and m is its mass .

putting the values

I = .5 x 95 x .38²

= 6.86 kg m²

n = 87 rpm = 87 / 60 rps

n = 1.45 rps

angular velocity ω = 2π n , n is frequency of rotation .

= 2 x 3.14 x 1.45

= 9.106 radian /s

frictional force = 16 x .2

= 3.2 N

torque created by frictional force = 3.2 x .38

= 1.216 N.m

angular acceleration = torque / moment of inertia

= - 3.2 / 6.86

α  = - 0.4665 rad /s²

b ) ω² = ω₀² +  2 α θ , where α is angular acceleration

0 = 9.106² - 2 x .4665 θ

θ = 88.87 radian

no of turns = 88.87 / 2π

= 14.15  turns

Answer:

Explanation:

To solve for the power consumed by the trains motor we have to employ the formula for power which is

Power= current * voltage

Given that

voltage V= 800 V

current I= 2130 A

Substituting in the formula for power we have

Power= 2130*800=  1704000 watt

Power = 1704 kW

This is the amount of energy consumed, transferred or converted per unit of time

Hence the power consumed  by the trains motor is 1704 kW

Answer

76200meters

Explanation:

we know that 1km=1000meters

to convert km into meters we we divide km by meters

=76.2/1000

=76200meters

Answer:

34°

Using the relation

θᶜ = sin^-1(n₂/n₁),

where n1= the refractive index of light is propagating from a medium

And n2 = refractive index of medium into which light is entering

So we know that

refractive index of diamond at 589nm = 2.41= n₁

refractive index of ethanol at 589nm and 20°C = 1.36= n₂

Thus. θᶜ = sin^-1(1.361/2.417) = 0.58radians = 34°

Explanation:

Answer:

a)   Δt = 24.96 s , b)  τ = 0.078 N m

Explanation:

This is a rotational kinematics exercise

        θ = w₀ t - ½ α t²

Let's reduce the magnitudes the SI system

       θ = 60 rev (2π rad / 1 rev) = 376.99 rad

       w₀ = 7.0 rot / s (2π rad / 1 rpt) = 43.98 rad / s

      α = (w₀ t - θ) 2 / t²

let's calculate the annular acceleration

      α = (43.98 10 - 376.99) 2/10²

      α = 1,258 rad / s²

Let's find the time it takes to reach zero angular velocity (w = 0)

        w = w₀ - alf t

         t = (w₀ - 0) / α

         t = 43.98 / 1.258

         t = 34.96 s

this is the total time, the time remaining is

         Δt = t-10

         Δt = 24.96 s

To find the braking torque, we use Newton's law for angular motion

        τ = I α

the moment of inertia of a circular ring is

       I = M r²

we substitute

         τ = M r² α

we calculate

        τ = 0.625  0.315²  1.258

        τ = 0.078 N m

The total time taken by the wheel to come to rest is 25.18 s and the magnitude of the frictional torque is 25.18 N-m.

Given data:

The initial angular speed of wheel is, [tex]\omega = 7.0 \;\rm rps[/tex]   (rps means rotation per second).

The time interval is, t' = 10.0 s.

The number of rotations made by wheel is, n = 60.0.

The mass of bike wheel is, m = 0.625 kg.

The radius of wheel is, r = 0.315 m.

The problem is based on rotational kinematics. So, apply the second rotational equation of motion as,

[tex]\theta = \omega t-\dfrac{1}{2} \alpha t'^{2}[/tex]

Here, [tex]\theta[/tex] is the angular displacement, and its value is,

[tex]\theta =2\pi \times 60\\\\\theta = 376.99 \;\rm rad[/tex]

And, angular speed is,

[tex]\omega = 2\pi n\\\omega = 2\pi \times 7\\\omega = 43.98 \;\rm rad/s[/tex]

Solving as,

[tex]376.99 = 43.98 \times 10-\dfrac{1}{2} \alpha \times 10^{2}\\\\\alpha = 1.25 \;\rm rad/s^{2}[/tex]

Apply the first rotational equation of motion to obtain the value of time to reach zero final velocity.

[tex]\omega' = \omega - \alpha t\\\\0 = 43.98 - 1.25 \times t\\\\t = 35.18 \;\rm s[/tex]

Then total time is,

T = t - t'

T = 35.18 - 10

T = 25.18 s

Now, use the standard formula to obtain the value of braking torque as,

[tex]T = m r^{2} \alpha\\\\T = 0.625 \times (0.315)^{2} \times 1.25\\\\T = 0.0775 \;\rm Nm[/tex]

Thus, we can conclude that the total time taken by the wheel to come to rest is 25.18 s and the magnitude of the frictional torque is 25.18 N-m.

Learn more about the rotational motion here:

https://brainly.com/question/1388042

Answer:

Apparent depth (Da) = 60.15 cm (Approx)

Explanation:

Given:

Distance from fish (D) = 80 cm

Find:

Apparent depth (Da)

Computation:

We know that,

Refractive index of water (n2) = 1.33

So,

Apparent depth (Da) = D(n1/n2)

Apparent depth (Da) = 80 (1/1.33)

Apparent depth (Da) = 60.15 cm (Approx)

The apparent depth of the fish is 60 cm.

To calculate the apparent depth of the fish, we use the formula below.

Formula:

Where:

Make D' The subject of the equation.

From the question,

Given:

Substitute these values into equation 2

Hence, the apparent depth of the fish is 60 cm

Learn more about apparent depth here: https://brainly.com/question/24319677

Answer:

The highest percentage of change corresponds to the thinnest rod, the correct answer is a

Explanation:

For this exercise we are asked to change the length of the bar by the action of a force applied along its length, in this case we focus on the expression of longitudinal elasticity

               F / A = Y ΔL/L

where F / A is the force per unit length, ΔL / L is the fraction of the change in length, and Y is Young's modulus.

In this case the bars are made of the same material by which Young's modulus is the same for all

              ΔL / L = (F / A) / Y

the area of ​​the bar is the area of ​​a circle

               A = π r² = π d² / 4

               A = π / 4 d²

we substitute

              ΔL / L = (F / Y) 4 /πd²

changing length

               ΔL = (F / Y 4 /π) L / d²

The amount between paracentesis are all constant in this exercise, let's look for the longitudinal change

a) values ​​given d and 3L

               ΔL = cte 3L / d²

               ΔL = cte L /d²  3

To find the percentage, we must divide the change in magnitude by its value and multiply by 100.

                ΔL/L % = [(F /Y  4/π 1/d²) 3L ] / 3L 100

                ΔL/L  % = cte 100%

b) 3d and L value, we repeat the same process as in part a

               ΔL = cte L / 9d²

               ΔL = cte L / d² 1/9

               ΔL / L% = cte 100/9

               ΔL / L% = cte 11%

c) 2d and 2L value

               ΔL = (cte L / d ½ )/ 2L

               ΔL/L% = cte 100/4

               ΔL/L% = cte 25%

d) value 4d and L

               ΔL = cte L / d² 1/16

                ΔL/L % = cte 100/16

                ΔL/L % = cte 6.25%

The highest percentage of change corresponds to the thinnest rod, the correct answer is a

Answer:

it is going to D. all of these are resistors

Answer:

His angular velocity will increase.

Explanation:

According to the conservation of rotational momentum, the initial angular momentum of a system must be equal to the final angular momentum of the system.

The angular momentum of a system = [tex]I[/tex]'ω'

where

[tex]I[/tex]' is the initial rotational inertia

ω' is the initial angular velocity

the rotational inertia = [tex]mr'^{2}[/tex]

where m is the mass of the system

and r' is the initial radius of rotation

Note that the professor does not change his position about the axis of rotation, so we are working relative to the dumbbells.

we can see that with the mass of the dumbbells remaining constant, if we reduce the radius of rotation of the dumbbells to r, the rotational inertia will reduce to [tex]I[/tex].

From

[tex]I[/tex]'ω' = [tex]I[/tex]ω

since [tex]I[/tex] is now reduced, ω will be greater than ω'

therefore, the angular velocity increases.

Answer:

Explanation:

Using the Continuity equation

v X A = v' xA'

so if A is 1/2of A' then A velocity must be 2 times the A'

after-contraction v = 2 x 5.0m/s = 10m/s

Using the Bernoulli equation

p₁ + ½ρv₁² + ρgh₁ = p₂ + ½ρv₂² + ρgh₂

, the "h" terms cancel

3.5 x 10^ 5Pa + ½ x 1000kg/m³x (5.0m/s)² = p₂ + ½ x 1000kg/m³ x (10m/s)²

p₂ = 342500pa

Answer:

 I = 7.96 W / m²

Explanation:

The light bulb emits a power of P = 100W, this power is distributed over the surface of a sphere, thus the emission is in all directions.

Intensity is defined by power per unit area

            I = P / A

The area of ​​a sphere is

         A = 4π r²

we substitute

         I = P / (4π r²)

in this case it tells us that the distance is r = 1 m

let's calculate

        I = 100 / (4π 1²)

        I = 7.96 W / m²

Answer:

386.13 N

Explanation:

The kinetic energy of the baseball is converted into workdone in moving the glove backward( work energy theorem).

Therefore, KE of the ball

[tex]\frac{1}{2} mv^2 =\frac{1}{2}(0.145)35^2\\ = 88.81 \text{J}[/tex]

Now, workdone in moving the glove

W= Fd

where F = Force applied, d = displacement of the glove= 0.23 cm.

88.81 = F×0.23

F= 88.81/0.23 = 386.13 N

Answer:

the pressure after contraction is 2×10^5 Pa

the speed after contraction is 15m/s

Explanation:

We were given Pressure P to be 3.5 x 10^5 that is Flowing with speed of 5.0 m/s,

For us to calculate pressure we need to calculate the area first as;

Let initial Area = A₁

And Final area A₂

We were told that in a horizontal pipe it contracts to 1/3 its former area. Which means

A₂= A₁/3.................

V₁ is the speed

the pressure and speed of the water after the contraction can be calculated using equation of continuity below

A₂V₂ = A₁V₁

But

If we substitute given value in the expresion we have

V₂ = (3A *5)/A

V₂ = 15m/s

Therefore, the speed after contraction is 15m/s

Now we can calculate the pressure using

Bernoulli's equation

p₁ + ½ρv₁² + ρgh₁ = p₂ + ½ρv₂² + ρgh₂

But we know that the pipe is horizontal, then "h" terms cancel out then

p₁ + ½ρv₁² = p₂ + ½ρv₂²

Making P₂ subject of formula we have

p₂ = 0.5ρ( V ₁² - v₂² ) + P₁

P₂=. 0.5 × 1000 (5² -15² ) + 3*10^5

=2×10^5 Pa

Therefore, the pressure after contraction is 2×10^5 Pa

(a)  the final speed of the water after contraction is 15 m/s.

(b) The final pressure of the water after contraction is 2.5 x 10⁵ Pa.

The given parameters;

Let the initial area of the pipe = A₁

Apply the continuity equation to determine the final speed of the water after contraction as follows;

[tex]A_1 V_1 = A_2 V_2\\\\V_2 = \frac{A_1V_1}{A_2} \\\\V_2 = \frac{A_1 \times 5}{\frac{1}{3} A_1 } \\\\V_2 = 15 \ m/s[/tex]

The final pressure of the water after contraction is determined by applying Bernoulli's equation for horizontal pipe;

[tex]P_1 + \frac{1}{2} \rho V_1^2= P_2 + \frac{1}{2} \rho V_2^2\\\\P_2 = \frac{1}{2} \rho (V_1^2 - V_2^2) + P_1\\\\P_2 = \frac{1}{2} \times 1000(5^2 - 15^2) + 3.5 \times 10^5\\\\P_2 = 2.5 \times 10^5 \ Pa[/tex]

Learn more here:https://brainly.com/question/19566865

Answer:

Explanation:

1 )

An object is placed 46.9 cm away from a converging lens. The lens has a focal length of 10.0 cm.

Since the object is placed at a distance more than twice the focal length , its image will be inverted , real  and will be of the size less than the size of object . So option B is applied .

B)  real, inverted and smaller than the object.

2 )

An object is placed 46.9 cm away from a spherical convex mirror. The radius of curvature of the mirror is 20.0 cm.

The object is placed at a point beyond its radius of curvature, its image will be formed at a point between f and C   or between focal point and centre of curvature . Its size will be smaller than size of object and it will be real and inverted .

B)  real, inverted and smaller than the object.

Answer:

The direction of the force will be towards the east

Explanation:

From the question we are told that  

    The direction of the  downward

Generally according to Fleming's right-hand rule(

          Thumb -  direction of force

           Middle finger -  direction of current

           Index finger -  direction of the magnetic field

) and the fact that the earth magnetic field acts  from south to north with respect to the four cardinal points then the direction of the  force will be toward the east with respect to the four cardinal point on the earth

Answer:

Explanation:

We shall apply conservation of momentum law in vector form to solve the problem .

Initial momentum = 0

momentum of 12 g piece

= .012 x 37 i since it moves along x axis .

= .444 i

momentum of 22 g

= .022 x 34 j

= .748 j

Let momentum of third piece = p

total momentum

= p + .444 i + .748 j

so

applying conservation law of momentum

p + .444 i + .748 j  = 0

p = - .444 i -  .748 j  

magnitude of p

= √ ( .444² + .748² )

= .87 kg m /s

mass of third piece = 58 - ( 12 + 22 )

= 24 g = .024 kg

if v be its velocity

.024 v = .87

v = 36.25 m / s .

Answer:

Explanation:

Formula used for calculating power P = current * voltage

P = IV

From ohms law, V = IR where R is the resistance. Substituting V = IR into the formula for calculating power, we will have;

P = IV

P =(V/R)V

P = V²/R

Given parameters

Power rating of the bulb P = 100 Watts

Source voltage V = 110V

Required

Resistance of the bulb R

Substituting the given parameters into the formula for calculating power to get Resistance R;

P = V²/R

100 = 110²/R

R = 110²/100

R = 110 * 110/100

R = 12100/100

R = 121 ohms

Hence, the resistance of this bulb is 121 ohms

Answer:

The  charge on the dust particle is  [tex]q_d = 6.94 *10^{-13} \ C[/tex]

Explanation:

From the question we are told that

    The length is  [tex]l = 2.0 \ m[/tex]

    The width is  [tex]w = 4.0 \ m[/tex]

   The charge is  [tex]q = -10\mu C= -10*10^{-6} \ C[/tex]

    The mass suspended in mid-air is [tex]m_a = 5.0 \mu g = 5.0 *10^{-6} \ g = 5.0 *10^{-9} \ kg[/tex]

Generally the electric field on the carpet is mathematically represented as

           [tex]E = \frac{q}{ 2 * A * \epsilon _o}[/tex]

Where [tex]\epsilon _o[/tex] is the permittivity of free space with value [tex]\epsilon_o = 8.85*10^{-12} \ \ m^{-3} \cdot kg^{-1}\cdot s^4 \cdot A^2[/tex]

substituting values

           [tex]E = \frac{-10*10^{-6}}{ 2 * (2 * 4 ) * 8.85*10^{-12}}[/tex]

           [tex]E = -70621.5 \ N/C[/tex]

Generally the electric force keeping the dust particle on the air  equal to the force of gravity acting on the particles

        [tex]F__{E}} = F__{G}}[/tex]

=>     [tex]q_d * E = m * g[/tex]

=>      [tex]q_d = \frac{m * g}{E}[/tex]

=>      [tex]q_d = \frac{5.0 *10^{-9} * 9.8}{70621.5}[/tex]

=>     [tex]q_d = 6.94 *10^{-13} \ C[/tex]

The color that is reflected when a red card is illuminated by red light is white.

The color an object is perceived to have, depends on the frequency of light it reflects.

If white light incidents on a red filter, red is transmitted while blue and green are absorbed.

Consequently, when a red card is illuminated by red light, the red card will  reflect back almost all the incident light on it, causing it to appear brighter which creates an  illusion of white color to the eyes.

Thus, we can conclude the color that is reflected when a red card is illuminated by red light is white.

Learn more here:https://brainly.com/question/3495999

Answer:

t = 23.6 min

Explanation:

First we need to find the mass of air in the room:

m = ρV

where,

m = mass of air in the room = ?

ρ = density of air at room temperature = 1.2041 kg/m³

V = Volume of room = 16 m x 16.5 m x 12.3 m = 3247.2 m³

Therefore,

m = (1.2041 kg/m³)(3247.2 m³)

m = 3909.95 kg

Now, we find the amount of energy consumed to heat the room:

E = m C ΔT

where,

E = Energy consumed = ?

C = Specific Heat of air at room temperature = 1 KJ/kg.⁰C

ΔT = Change in temperature = 21 °C - 13.5 °C = 7.5 °C

Therefore,

E = (3909.95 kg)(1 KJ/kg.°C)(7.5 °C)

E = 29324.62 KJ

Now, the time period can be calculated as:

P = E/t

t = E/P

where,

t = Time needed = ?

P = Power of heater = 20.7 KW

Therefore,

t = 29324.62 KJ/20.7 KW

t = (1416.65 s)(1 min/60 s)

t = 23.6 min

Answer:

C. planetary accretion

Explanation:

Astronomers think planets formed from interstellar dust gases that clumped together in a process called planetary accretion.

Answer:

[tex]\boxed{\sf C. \ planetary \ accretion }[/tex]

Explanation:

Astronomers think planets formed from interstellar dust and gases that clumped together in a process called planetary accretion.

Planetary accretion is a process in which huge masses of solid rock or metal clump together to produce planets.

Answer:

At the moment contact is made with the battery, the voltage across the resistor is equal to the batteries terminal voltage

Explanation;

Because at series connection the battery and resistor have equal voltage

Answer:

v = 6.28 m/s

Explanation:

It is given that,

A windmill on a farm rotates at a constant speed and completes one-half of a rotation in 0.5 seconds,

Number of revolution is half. It means angular velocity is 3.14 radians.

Let v is the angular speed. So,

[tex]v=\dfrac{\omega}{t}\\\\v=\dfrac{3.14}{0.5}\\\\v=6.28\ m/s[/tex]

So, the rotation speed is 6.28 m/s.

The angular velocity is the rotation speed, which is the angle of rotation

of the windmill per second, which is 2·π radians.

Response:

The given parameter are;

The angle of rotation the windmill rotates in 0.5 seconds = One-half a

rotation.

Required:

The rotational speed (angular velocity)

Solution:

The angle of one rotation = 2·π radians

Angle of one-half ration = [tex]\frac{1}{2}[/tex] × 2·π radians = π radians

[tex]Rotational \ speed = \mathbf{\dfrac{Angle \ of \ rotation}{Time}}[/tex]

Which gives;

[tex]Rotational \ speed, \omega = \dfrac{\pi}{0.5 \ s} = \mathbf{2 \cdot \pi \ rad/s}[/tex]

Learn more about rotational speed here:

https://brainly.com/question/6969329

Answer:

The  radius of the earth is [tex]r = 6365.4 \ km[/tex]

Explanation:

From the question we are told that

     The distance at  Alexandria is  [tex]d_a = 800 \ km = 800 *10^{3} \ m[/tex]

      The angle of the sun is  [tex]\theta = 7.2 ^o[/tex]

So we want to first obtain the circumference of the earth

   So let assume that the earth is  circular ([tex]360 ^o[/tex])

  Now from question we know that the sun made an angle of [tex]7.2 ^o[/tex] so with this we will obtain how many  [tex](7.2 ^o)[/tex]  are in [tex]360^o[/tex]

 i.e    [tex]N = \frac{360}{7.2}[/tex]

=>      [tex]N = 50[/tex]

     With this  value we can evaluate the circumference as

             [tex]c = 50 * 800[/tex]

              [tex]c = 40000 \ km[/tex]

Generally circumference is mathematically represented as

        [tex]c = 2\pi r[/tex]

         [tex]40000 = 2 * 3.142 * r[/tex]

=>        [tex]r = 6365.4 \ km[/tex]

Answer:

Explanation:

The phase angle of an RLC circuit  ϕ is expressed as shoen below;

ϕ = [tex]tan^{-1} \dfrac{X_l-X_c}{R}[/tex]

Xc is the capacitive reactance = 1/2πfC

Xl is the inductive reactance = 2πfL

R is the resistance = 25.0Ω

Given C = 35.5 μF, L = 0.0940 H, and frequency f = 70.0Hz

Xl = 2π * 70*0.0940

Xl = 41.32Ω

For the capacitive reactance;

Xc = 1/2π * 70*35.5*10⁻⁶

Xc = 1/0.0156058

Xc = 64.08Ω

Phase angle ϕ = [tex]tan^{-1} \frac{41.32-64.08}{25} \\\\[/tex]

ϕ = [tex]tan^{-1} \frac{-22.76}{25} \\\\\\\\[/tex]

[tex]\phi = tan^{-1} -0.9104\\\\\phi = -42.31^0[/tex]

Since tan is negative in the 2nd quadrant;

[tex]\phi = 180-42.31^0\\\\\phi = 137.69^0[/tex]

Hence the phase angle ϕ of the circuit in degrees is 137.69°

The phase angle ϕ of the series RLC circuit that is driven at a frequency of 70.0 Hz is ϕ = 137.69°

Given that:

capacitance C = 35.5 μF,

Inductance L = 0.0940 H,

The resistance R = 25.0Ω

and frequency f = 70.0Hz

The capacitive reactance is given by:

Xc = 1/2πfC

Xc = 1/2π × 70 × 35.5× 10⁻⁶

Xc = 1/0.0156058

Xc = 64.08Ω

The inductive reactance is given by:

Xl = 2πfL

Xl = 2π × 70 × 0.0940

Xl = 41.32Ω

The phase angle of an RLC circuit ϕ  is given by:

[tex]\phi=tan^{-1}\frac{X_l-X_c}{R}\\\\\phi=tan^{-1}\frac{41.32-64.08}{25}[/tex]

Ф = -42.31°

Since tan is negative in the 2nd quadrant, thus:

ϕ = 180° - 42.31°

ϕ = 137.69°

Learn more about RLC circuit:

https://brainly.com/question/372577?referrer=searchResults

The researchers need to compare those who contracted the disease to those who did not.

Answer:

1.6×10²⁰

Explanation:

An ampere is a Coulomb per second.

1 A = 1 C / s

The amount of charge after 5 seconds is:

5.0 A × 5 s = 25 C

The number of electrons is:

25 C × (1 electron / 1.6×10⁻¹⁹ C) = 1.6×10²⁰ electrons