A car travelling at 22.4 m/s skids to a stop in 2.55s. Determine the skidding distance of the car (assume uniform acceleration).

The meter stick is in static rotational equilibrium, which means that the sum of the clockwise torques must equal the sum of the counterclockwise torques. The torque is equal to the force multiplied by the distance from the support point, so we can set up the equation:  
CW Torque (5 cm mark): 220 g x 5 cm = 1100 g-cm
CW Torque (90 cm mark): 120 g x 90 cm = 10,800 g-cm
CCW Torque (40 cm mark): M x 40 cm = M x 40 cm
1100 g-cm + 10,800 g-cm = M x 40 cm
M = (1100 + 10,800) / 40 = 250 g
Therefore, the mass of the meter stick is 250 g.

Rotational equilibrium refers to the condition in which an object is motionless and still rotating. The condition occurs when the net torque on an object is equal to zero.

Read more about the topic of rotational equilibrium:

rainly.com/question/31142588

#SPJ11

The fluid movement in a lava lamp is caused by the heat generated from the lamp's light bulb, which causes the wax or oil to rise and fall.

A lava lamp contains two fluids of different densities that do not mix. The fluids heat up as a result of the lamp's light bulb, causing them to expand and become less dense. The wax or oil floats up when it becomes less dense than the fluid that surrounds it, creating a globe at the top of the lamp.

The fluid is then cooled by the environment and becomes more dense, causing the wax to sink back to the bottom. This constant motion cycle creates the flowing effect seen in a lava lamp.

The heat from the light bulb causes the fluid to expand, and as it does, it becomes less dense than the surrounding fluid, causing it to float. When the fluid cools, it becomes denser and settles back down to the bottom. This cyclic motion creates the soothing flow of a lava lamp.

For more such questions on lava lamp, click on:

https://brainly.com/question/30542979

#SPJ11

At the shop, Joselyn purchased 2700 grammes of salt water taffy.

To convert kilograms (kg) to grams (g), Joselyn would need to multiply the weight in kilograms by 1000. This is because there are 1000 grams in 1 kilogram. Therefore, to find out how many grams of salt water taffy Joselyn bought, she would need to multiply 2.7kg by 1000.

The correct answer is (B) Multiply by 1000.

Multiplying 2.7kg by 1000 gives:

2.7kg x 1000 = 2700g

So Joselyn bought 2700 grams of salt water taffy at the store.

To learn more about salt water refer to:

brainly.com/question/6829606

#SPJ4

When only one lightbulb blows out, an entire string of decorative lights goes out, which means that the lights in this string must be connected in series with one current pathway.

In a series circuit, the components are connected end to end in a single path, so the current flows through each component in turn. If one component, such as a lightbulb, fails, the circuit becomes incomplete, and the current cannot flow through any of the components downstream of the failed component. This results in all the lights in the series circuit going out when one lightbulb blows out.

In contrast, in a parallel circuit, the components are connected across multiple current pathways, so if one component fails, the current can still flow through the other components, and they will continue to function normally. Therefore, if one lightbulb blows out in a parallel circuit, the other lights will continue to work.

Learn more about the series circuit:

https://brainly.com/question/19865219

#SPJ11

The volume of the solid obtained by rotating the region in the first quadrant bounded by the curves x = 0, y = 1, x = y^7 about the line y = 1 is 0.

To determine the volume of the solid obtained by rotating the region in the first quadrant bounded by the curves x = 0, y = 1, x = y^7 about the line y = 1, we need to use a specific integral formula.

The volume of the solid is calculated by multiplying the area of the cross-section of the solid, which is perpendicular to the axis of rotation, with the distance traveled by the center of mass of the cross-section. And, when this product is summed up across the length of the solid, we get the volume of the solid.

To solve the given problem, the area of the cross-section of the solid is [tex]\pi (r)^2[/tex], where r is the distance from the line y = 1 to the curve [tex]x = y^7[/tex]. Since the cross-section is a circle, we know the area of the cross-section can be represented by the equation of a circle with radius r, which is [tex]\pi (r)^2[/tex].

To find the value of r, we will equate  [tex]x = y^7[/tex] to the line y = 1. By solving for y, we get: [tex]y = 1^{1/7} = 1[/tex].

Hence, r = 1 - 1 = 0.

We can now compute the volume of the solid using the integral formula:

[tex]V =\int_0^1 \pi (r)^2 dy\\V = \int_0^1 \pi (0)^2 dy\\V = \int_0^1 0 dy\\V = 0[/tex]

Learn more about volume of the solid here:

https://brainly.com/question/24259805

#SPJ11

The work required to raise the elevator from the basement to the third floor is equal to the force times the distance moved. The work required is equal to (-pounds)(ft) = -foot-pounds.

We have to calculate the work required to raise the elevator from the basement to the third floor using the given data. In order to calculate the work, we need to determine the force required to lift the elevator.

This can be done using the equation: F = W + w x L

where, F is the force required to lift the elevator, W is the weight of the elevator, w is the weight of the cable per foot, and L is the length of the cable. F = 1500 + (0.4 × 75) = 1500 + 30 = 1530 pounds.

Therefore, the force required to lift the elevator is 1530 pounds. The work done to raise the elevator is given by the equation: W = F × d

where, W is the work done, F is the force required to lift the elevator, and d is the distance traveled by the elevator.

W = 1530 × 30 = 45,900 foot-pounds.

Therefore, the work required to raise the elevator from the basement to the third floor is 45,900 foot-pounds.

Read more about the distance ;

https://brainly.com/question/26550516

#SPJ11

One of the methods which will not reduce reactivity of observation is telling the person you are observing his/her behaviour. Correct option is B.

A practical, utilitarian approach, behavioral observation focuses on the plainly discernible ways in which the client engages with his or her surroundings. Behavioural observation can be used as a standalone technique or casually as a component of an interview, a test, or both.

Waiting until the subjects of the observation are used to the observer is one method to reduce reactivity. Another option is to have the observer document the actions without the subjects being aware of the observation.

The act of observation modifies in some manner the situation in which a participant is being observed. Within an experimental setting, reactivity is viewed as a threat to internal validity because the change in behaviour is not due to the experimental manipulation. Best choice is B.

To know more about observations:

https://brainly.com/question/30454101

#SPJ4

The wave interaction that occurs when two waves are in the same place at the same time is called interference.

Interference can be either constructive or destructive, depending on the relative phases of the waves.

What is constructive interference?

Constructive interference occurs when two waves have the same phase and their amplitudes add together. The resulting wave has a larger amplitude than either of the individual waves. This can be seen, for example, when two speakers playing the same sound are placed close together.

What is destructive interference?

Destructive interference occurs when two waves have opposite phases and their amplitudes subtract from each other. The resulting wave has a smaller amplitude than either of the individual waves. This can be seen, for example, when two waves with equal amplitude and wavelength are superimposed, but one is shifted by half a wavelength relative to the other.

To know more about interference, visit:

https://brainly.com/question/16098226

#SPJ1

Complete question is: The wave interaction that occurs when two waves are in the same place at the same time is called interference.

All but  option A: the plant is exposed to light condition must be present for the Calvin cycle reactions to occur.

The Calvin cycle is the biochemical process that takes place in the chloroplasts of plants, in which carbon dioxide is fixed into glucose molecules. This process involves several enzymes and molecules, but the energy needed to power the process comes from ATP and NADPH, which are produced during the light-dependent reactions that take place in the thylakoid membranes of the chloroplasts.

Therefore, light is required for the Calvin cycle to occur since it is the source of the energy that drives the reaction. However, all parts of the plant do not need to be exposed to light for the Calvin cycle to occur. Only the chloroplasts, which are found in the mesophyll cells of the plant, need to be exposed to light for photosynthesis to occur.

Learn more about Calvin cycle from

https://brainly.com/question/920840

#SPJ1

See full question below

all but which condition must be present for the calvin cycle reactions to occur?

The plant is exposed to light

water is not involved in any of the reactions

light energy is converted into chemical energy

provide the electrons needed to reduce NADP

Coordinate , A - the height of the stone when it hits the water. A slingshot sends a stone vertically upward from a height of 20 feet above a pool of water.

The coordinate A represents the height of the stone when it hits the water. When the stone hits the water, its height above the water surface is zero.

So, we can set the expression for the stone's height equal to zero and solve for t to find the time when the stone hits the water. The height of the stone when it is launched is given as 20 feet, which is a fixed value in this problem.

The time when the stone is launched is also a fixed value, which is zero. The maximum height of the stone is the highest point the stone reaches above its initial height of 20 feet. The time when the stone reaches its maximum height is the time at which the vertical velocity of the stone becomes zero.

To know more about vertical velocity , visit :

https://brainly.com/question/11679227

#SPJ1

Answer:

Explanation:

a) The mass of the cube can be calculated using the equation Mass = Volume x Density. The volume of the cube can be calculated as (5.00×10 cm)^3 = 125 cm³. Substituting this volume into the equation gives Mass = 125 cm³ x 7.86 g/cm³ = 983.5 g.

b) The number of iron atoms in the cube can be calculated using Avogadro's number (6.02 x 10^23 atoms/mol). The number of moles can be calculated using the molar mass of iron, 55.9 g/mol. Thus, the number of moles can be calculated as 983.5 g / 55.9 g/mol = 17.61 moles. Multiplying this by Avogadro's number gives the number of iron atoms in the cube as 1.07 x 10^24 atoms.

The Volumetric efficiency of the pump is the ratio of the actual capacity to the theoretical capacity of the pump.

Volumetric efficiency of the pump = Actual capacity of the pump / Theoretical capacity of the pump

Given Information

The provided information is,

Find

The theoretical capacity of the pump is given by the following formula,

Theoretical capacity of the pump = π/4 x d² x l x n

where:

For the given problem,

We need to find the diameter of the pump and length of the pump to calculate the theoretical capacity of the pump.

Now, we have the actual capacity of the pump.

As we don't have the diameter and length of the pump, it is impossible to calculate the theoretical capacity of the pump.

Hence, the Volumetric efficiency of the pump cannot be calculated.

Learn more about Volumetric efficiency: https://brainly.com/question/14783214

#SPJ11

The fluid force on one side of the 5ft by 5ft plate lying flat on its 5ft by 5ft face, we can use the equation F = ρghA and the F = 1,945,000 N.

Since the plate is at the bottom of the pool and the pool is filled with water to a depth of 8ft, h = 8ft and the area of the plate A = 5ft × 5ft = 25ft².

There F is the fluid force, ρ is the density of the fluid, g is the acceleration due to gravity, h is the depth of the fluid, and A is the area of the plate.

Therefore, the fluid force on one side of the plate is:

F = ρghA = 1000kg/m³ × 9.81m/s² × 8ft × 25ft² = 1,945,000 N.

To calculate the fluid force on one side of the plate resting vertically on a 5 ft edge, we can use the same equation as above but with an area equal to the length of the plate multiplied by the depth of the pool (8ft):

F = ρghA = 1000kg/m³ × 9.81m/s² × 8ft × 5ft = 392,000 N.

To calculate the fluid force on one side of the plate resting on a 5ft edge and tilted at 45 degrees to the bottom of the pool, we can use the same equation as above but with an area equal to the length of the plate multiplied by the depth of the pool multiplied by the cosine of the angle of the plate:

F = ρghA = 1000kg/m³ × 9.81m/s² × 8ft × 5ft × cos(45) = 283,200 N.

Read more about the force here:

https://brainly.com/question/12785175

#SPJ11

Hominin remains have been found at sites throughout Africa, Europe, and Asia. Below are five of these fossil sites and their main finds. The correct order of the given hominin fossil sites from oldest to youngest is Omo kibish, Klasies river, Herto, and Tianyuan cave.

Omo kibish is incomplete fossil skull (oldest)The oldest fossil site on the list is Omo kibish in Ethiopia, which is dated to around 195,000 years ago. The site has a partial skull, lower jawbone, and a few other fragments of the skull. Klasies river is fragmentary hominin remains Klasies river Mouth in South Africa is dated back to around 120,000 years ago. The site contains human fossils along with the remains of other animals.

Herto is a skull intermediate between H. heidelbergensis and modern H. sapiens, Herto Bouri in Ethiopia, dated to around 160,000 years ago. The site contains 3 complete hominid skulls which were much more modern than expected for their age. The skulls were similar to Homo sapiens, but with some differences. Tianyuan cave is modern human maniple and femur (youngest). Tianyuan cave in China, dated to around 40,000 years ago, contains one of the earliest modern human fossils. A complete set of human teeth and bones from a foot, leg, and hand were found at this site.

Learn more about hominin at:

https://brainly.com/question/30791663

#SPJ11

The electric field inside the wire is still about 2.27 V/m, even though the electron mobility is 4 times higher. This is because the resistance of the wire remains the same, and Ohm's law still applies. The higher conductivity only means that a higher current flows through the wire for the same voltage, but the electric field remains the same.

We can use Ohm's law to find the electric field inside the Nichrome wire:

V = IR

where

V = 1.7 volts (battery voltage)

I = current

R = resistance of the wire

The resistance of a wire can be calculated using the formula:

R = (ρL) / A

where

ρ = resistivity of the material

L = length of the wire

A = cross-sectional area of the wire

The resistivity of Nichrome is about 1.10 x 10^-6 Ωm, and the cross-sectional area of the wire can be calculated using the formula for the area of a circle:

A = πr^2

where

r = radius of the wire = 0.125 mm = 0.000125 m

So, A = π(0.000125 m)^2 = 4.91 x 10^-8 m^2

Substituting the values, we get:

R = (1.10 x 10^-6 Ωm)(0.75 m) / (4.91 x 10^-8 m^2)

R ≈ 0.017 Ω

Now we can find the current:

I = V / R

I = 1.7 volts / 0.017 Ω

I ≈ 100 amps

The electric field inside the wire can be calculated using the formula:

E = V / L

where

E = electric field

V = potential difference

L = length of the wire

Substituting the values, we get:

E = 1.7 volts / 0.75 m

E ≈ 2.27 volts/meter or 2.27 V/m

So the electric field inside the Nichrome wire is about 2.27 V/m.

Next, we can repeat the calculations for the wire with the higher electron mobility. Since the mobile electron density and the length and diameter of the wire are the same, the resistance of the wire will also be the same as before. However, the higher electron mobility means that the wire will have a higher conductivity, which in turn means that the current will be higher for the same voltage.

Let's assume that the electron mobility is 4 times higher than that of Nichrome. Since the resistivity of the material remains the same, the conductivity will be 4 times higher as well. Therefore, the current will be 4 times higher than before:

I = 4 x 100 amps = 400 amps

Using the same formula as before, the electric field inside the wire can be calculated:

E = V / L

E = 1.7 volts / 0.75 m

E ≈ 2.27 volts/meter or 2.27 V/m

So, the electric field inside the wire is still about 2.27 V/m, even though the electron mobility is 4 times higher. This is because the resistance of the wire remains the same, and Ohm's law still applies. The higher conductivity only means that a higher current flows through the wire for the same voltage, but the electric field remains the same.

For such more questions on Ohm's law

https://brainly.com/question/14634041

#SPJ11

The average arterial pressure in your hands when they are held at your side is 47.5 mmHg.

The average arterial pressure in your hands when they are held at your side can be determined using the hydrostatic pressure formula, which is a function of height, gravity, and density. When the hands are held at the side, they are 60 cm below the heart, which means they are at a distance of 0.6 m.

The hydrostatic pressure formula is given by

P = ρgh

Where,

P is the pressure, ρ is the density, g is the acceleration due to gravity, and h is the height. We can assume that the density of blood is constant, and we can take the value of g to be 9.81 m/s², the standard acceleration due to gravity.

Therefore, the pressure at the heart is 100 mmHg, or 100/760 = 0.131 atm. The pressure in the hands can be calculated as follows:

P = ρghP = (1.06 × 10³ kg/m³) × (9.81 m/s²) × (0.6 m)

P = 6.26 × 10³ N/m²

P = 6.26 × 10³ Pa

P = 47.5 mmHg

Therefore, the average arterial pressure in the hands when they are held at the side is 47.5 mmHg.

Learn more about hydrostatic pressure at https://brainly.com/question/28206120

#SPJ11

The coordinated functions of the Nervous, Endocrine, and Reproductive systems are:

Coordinated functions refer to the integration and communication between different organs, systems, and tissues in the body to achieve a common goal or purpose. In biological terms, coordinated functions often involve multiple physiological systems working together to maintain homeostasis, respond to stimuli, or carry out complex behaviors or processes.

Examples of coordinated functions include the regulation of blood glucose levels by the pancreas and liver, the coordination of movement by the nervous and musculoskeletal systems, and the release of hormones by the endocrine system to control various physiological processes.

Learn more on coordinated functions here: https://brainly.com/question/15686131

#SPJ1

The question is:

"COORDINATED FUNCTIONS OF THE NERVOUS, ENDOCRINE, AND REPRODUCTIVE SYSTEMS"

Directions: Identify the part of the brain that is involved in each situation below. Write only the letter of your answer.

A. Amygdala

B. Brocka's Area

C. Cerebellum

D. Cerebrum

E. Hippocampus

F. Occipital Lobe

G. Hippocampus

H. Hypothalamus

I. Inferior Colliculus.

J. Thalamus

K. Pons

L Superior Colliculus

M. Pineal Gland

N. Wernicke's Area

O. Pituitary Gland

1. "My heart tells me that you are the one. I love you so much!"

2. "IAOCEVOY! I don't know what that means. It's all Greek to me!"

3. "Chartreuse, Olive,Turquoise, and Mint are all shades of green."

4. "Janna always wakes up at 4 in the morning, regardless of whether she uses an alarm clock or not."

5. "I don't remember the way going to Myla's house. Can you accompany me there?"

6. Jenny's mother is about to give birth, she complains about contraction and pain usually when the baby is kicking

7. "Anthony is a very skilled dancer. He just won the school hip hop dance competition last week."

8. "As Nica was walking on the road she readily moved to the side for she heard an incoming ambulance"

9. "Elsa loves making faces whenever she talks to her friends."

10. "Ryan usually talks about how happy his high school days were to his grandchildren."

The example in which the distance you travel is different from your

displacement will be "Suppose a person starts at point A and walks 5 meters to point B, and then turns around and walks back to point A, covering another 5 meters. The distance traveled by the person is the total length of the path traveled, which is 10 meters (5 meters + 5 meters).

However, the displacement of the person is the change in position from the starting point to the ending point, which is zero. So the distance traveled is different from the displacement, as the person ends up at the same position where they started, despite covering a total distance of 10 meters.

Displacement is a verb that denotes movement or displacement of an object. The definition of displacement is the modification of an object's position.

The term "displacement" refers to a shift in an object's position. It is a vector quantity with a magnitude and direction. The symbol for it is an arrow pointing from the initial location to the ending place. For instance, if an object shifts from location A to position B, its position changes.

Learn more about displacement on:

https://brainly.com/question/14422259

#SPJ1

The statement the construction of psychological profiles is a process of mapping the characteristics of offenders of previously solved crimes and applying them to offenders of unsolved ones is TRUE.

Psychological profiling is a technique used by law enforcement agencies to identify the characteristics of an offender based on their behavior patterns, motives, and other psychological traits. It is a process of creating a psychological profile of an offender by analyzing the crime scene, victimology, and other evidence related to the crime.

This profile is then compared with the profiles of previously solved crimes to identify potential suspects or patterns that can be used to solve unsolved crimes. The process involves mapping the characteristics of offenders of previously solved crimes and applying them to offenders of unsolved ones.

The psychological profile is based on the assumption that an offender's behavior is consistent across different crimes and that it reflects their personality traits and motivations. This technique has been used successfully in many high-profile cases and has helped law enforcement agencies to identify and apprehend serial offenders.

To know more about psychological profiles, refer here:

https://brainly.com/question/30398442#

#SPJ11

Answer:

It would triple.

Explanation:

By Newtown's law of universal gravitation, the ration is 1:1

The frequency detected by a stationary observer if the ambulance truck is moving 30 m/s toward the observer is 731.3 Hz.

When the ambulance truck emits sound with a frequency of 800hz and the ambulance truck is moving 30 m/s toward the observer,

The observed frequency is given by the following formula.

f’ = f [(v ± v_o)/(v ± v_s)]

Where v = the speed of sound in air = 343 m/s

f = frequency of the source = 800 Hz

v_o = velocity of the observer (stationary) = 0 m/s

v_s = velocity of the source (ambulance truck) = -30 m/s (since the ambulance truck is moving toward the observer)

Now we can plug in the values into the formula and calculate the observed frequency.

f' = 800 ((343 - 30) / (343 + 0))

= 800 (313 / 343)

= 731.5 Hz (rounded to one decimal place)

If the ambulance truck is moving towards a stationary observer at a speed of 30 m/s, the frequency detected by the observer is 731.3 Hz.

To know more about "observed frequency" in physics: https://brainly.com/question/15056533

#SPJ11

A, B, and C are all assumptions made in the model for the motion of a pendulum, and if any of them are not valid, the model may not accurately describe the behavior of the pendulum. Therefore, option D is correct.

The model for the motion of a pendulum assumes that the pendulum is swinging without friction, the string is massless, and the amplitude of oscillation is small. These assumptions allow us to use the simple harmonic motion equation to describe the motion of the pendulum. However, if any of these assumptions are not true, the model may not be valid.

Therefore, if any of these assumptions are not valid, the model for the motion of the pendulum may not be accurate, and the results obtained from the model may not describe the actual behavior of the pendulum.

Hence Option d IS CORRECT.

For more similar questions on pendulum,

brainly.com/question/12306298

#SPJ11.

The proper subset relations that are possible using the sets of numbers n, z, q, and r are:

An improper subset comprises every element of the original set, while a valid subset only contains a fraction of the original set's numbers. A subset of a set A that is not equal to A is a proper subset of A. In other words, if B is a proper subset of A, then A has at least one element that is not in B but all of B's elements are in A.

Learn more about proper subset at brainly.com/question/17514113

#SPJ11

The correct option is B, the areas labeled X, Y, and Z represent constructive interference in which waves strengthen each other.

Interference is a phenomenon that occurs when two or more waves interact with each other. In physics, waves can be described as a disturbance that travels through a medium, such as water or air. When two waves meet, they can either reinforce or cancel each other out, depending on their amplitudes and phases.

Constructive interference occurs when the peaks of two waves coincide, creating a larger amplitude than either wave alone. Destructive interference occurs when the peak of one wave coincides with the trough of another, resulting in a cancellation of the waves. Interference is a fundamental concept in many areas of physics, including optics, acoustics, and electromagnetism.

To learn more about Interference visit here:

brainly.com/question/16098226

#SPJ4

Complete Question:

The diagram shows monochromatic light passing through two openings.

What do the areas labeled X, Y, and Z represent?

A). constructive interference in which waves cancel each other out

B). constructive interference in which waves strengthen each other

C). destructive interference in which waves cancel each other out

D). destructive interference in which waves strengthen each other

Galileo famously observed that objects of different masses fall to Earth at the same rate, regardless of their mass. This observation led him to conclude that gravity was a universal force of attraction between any two objects with mass.

Galileo Galilei was an Italian astronomer, physicist, and mathematician who contributed greatly to the development of modern science. His contributions to physics include the creation of the scientific method and his work on the principles of motion and gravity.

Galileo was one of the first scientists to study gravity. He observed that objects of different weights would fall at the same rate when dropped from the same height. This led him to conclude that gravity is a constant force that acts upon all objects equally, regardless of their weight or composition.

Galileo's work on gravity laid the foundation for the later development of Sir Isaac Newton's theory of gravity. Newton built on Galileo's findings and formulated the law of universal gravitation, which states that every object in the universe attracts every other object with a force that is proportional to their masses and inversely proportional to the square of the distance between them.

Learn more about Galileo at https://brainly.com/question/4966012

#SPJ11

The sample size with some specified width error by reducing the confidence level to 80% is 3 times the original sample size and the width error which have been scaled in size compared to the original width error is by a factor of 10.

When reducing the confidence level to 80% and the original width (error) E by a third, the new sample size will be 3 times the original size. To calculate this, use the formula n = (zα/2 / E)² × σ2.

If the original confidence level was 95%, then the original zα/2 = 1.96. If the new confidence level is 80%, then the new zα/2 = 1.282.

The original error was E, and the new error is 1/3 E. By substituting these values into the formula, we get n = (1.282 / (1/3 E))² × σ2. This simplifies to n = 3 × (1.96 / E)² × σ2, which is 3 times the original sample size.

If the original confidence level was 95%, then the original zα/2 = 1.96.

If the new confidence level is 85%, then the new zα/2 = 1.44.

The original error was E, and the new error is 10E.

By substituting these values into the formula, we get n = (1.44 / (10E))² × σ2.

This simplifies to n = (1.96 / E)² × σ2, which is 10 times the original sample size.

Therefore, the width (error) will have scaled in size by a factor of 10 compared to the original width (error) E.

Learn more about Sample size here:

https://brainly.com/question/25894237

#SPJ11

True. A Faraday bag (also known as an electromagnetic bag) is a container made from metal or a special material that blocks any electromagnetic emanations from passing into or out of the bag, preventing a mobile device from communicating with the outside world.

This is because Faraday bags are electromagnetic bags that are designed to isolate electronic devices from external electromagnetic influence. They are also known as radiofrequency shielding bags, Faraday cage bags, signal blocker bags, or electromagnetic pulse (EMP) bags.

What are Faraday bags?

Faraday bags are made of a combination of metal or metal-coated fabrics that are designed to block electromagnetic signals from entering or leaving the bag. They are usually used to keep mobile devices such as smartphones and tablets from communicating with the outside world, especially in situations where an individual is worried about their privacy or security. They are also used by law enforcement agencies to prevent suspects from remotely wiping or deleting evidence on their devices.

How do Faraday bags work?

Faraday bags work by using a principle known as the Faraday effect, which states that any electric field in a conductor is shielded from the conductor's interior by the presence of an electric field. Faraday bags use this principle to block incoming and outgoing signals by creating an electrically conductive enclosure around the device. This means that when a mobile device is placed inside a Faraday bag, the bag acts as a Faraday cage, which shields the device from electromagnetic radiation. As a result, the device cannot communicate with the outside world.

For further details about Faraday bag, click on the below link:

https://brainly.com/question/23083952

#SPJ11

Answer:

Light energy

Explanation:

When an electron releases or absorbs energy, it goes into an "exited state" which means it goes into a lower or higher energy level respectively. This will radiate light energy.

The most appropriate option among the given options is C. A white dwarf is what most stars become when they die.What is a white dwarf?A white dwarf is a small, compact object that is the final stage of stellar evolution for most stars in the universe.

The star exhausts its fuel and begins to cool after it has used up all of the hydrogen fuel that powers its nuclear reactions. This phase of a star's evolution is referred to as a red giant. The star then sheds its outer layers of gas, exposing its core. The hot, glowing core of a star is exposed as a white dwarf once the outer layers have been ejected.What most stars become when they die is a white dwarf. This is one of the most fascinating phenomena in the universe, as well as one of the most intriguing. Furthermore, a white dwarf is a dense, compact object that is frequently composed of carbon and oxygen. It has no more nuclear fuel to burn, therefore it does not produce energy. As a result, it gradually fades away into the blackness of space, eventually turning into a black dwarf. However, it is believed that no black dwarfs have been observed yet.White dwarfs are not precursors to black holes or neutron stars, as those objects are formed from more massive stars that undergo different processes at the end of their lives. Brown dwarfs are also different objects, being failed stars that never achieved the temperature and pressure necessary for sustained nuclear fusion.

For more such questions one white dwarf

https://brainly.com/question/13914155

#SPJ11

The factor that does not determine how much gravitational potential energy is in an object-earth system is the object's mass.

An object-earth system is a system in which an object interacts with the earth by exerting a force of attraction. The object's energy is derived from the work done by gravitational forces when the object is moved away from the earth's surface.

An object in an object-earth system's gravitational potential energy is the work done by gravitational forces on the object when it is moved from a lower position to a higher one in the object-earth system. The factor that does not determine how much gravitational potential energy is in an object-earth system is the object's mass. The gravitational potential energy of an object in the earth-object system is determined by the distance between the object and the earth's surface. The gravitational potential energy of an object increases as the distance between it and the earth's surface increases.

Learn more about the gravitational potential at brainly.com/question/19768887

#SPJ11