A cell membrane has a thickness of about 7 nm. How many cell membranes would it take to make a stack 2.3 in high?

Answer:

Train accaleration = 0.70 m/s^2

Explanation:

We have a pendulum (presumably simple in nature) in an accelerating train. As the train accelerates, the pendulum is going move in the opposite direction due to inertia. The force which causes this movement has the same accaleration as that of the train. This is the basis for the problem.

Start by setting up a free body diagram of all the forces in play: The gravitational force on the pendulum (mg), the force caused by the pendulum's inertial resistance to the train(F_i), and the resulting force of tension caused by the other two forces (F_r).

Next, set up your sum of forces equations/relationships. Note that the sum of vertical forces (y-direction) balance out and equal 0. While the horizontal forces add up to the total mass of the pendulum times it's accaleration; which, again, equals the train's accaleration.

After doing this, I would isolate the resulting force in the sum of vertical forces, substitute it into the horizontal force equation, and solve for the acceleration. The problem should reduce to show that the acceleration is proportional to the gravity times the tangent of the angle it makes.

I've attached my work, comment with any questions.

Side note: If you take this end result and solve for the angle, you'll see that no matter how fast the train accelerates, the pendulum will never reach a full 90°!

Answer:

football

Explanation:

I took the 2.10 quiz and got it wrong so it must be football

Explanation:

Hi,

The answer is friction.

There is almost no machine which are not affected by friction. It losts some work due to friction while working.

Hope it helps..

Answer:

friction

Explanation:

the other options dont effect efficiency

Answer:

healthy diet

Explanation:

Exercise and a healthy diet are the two things people do to stay healthy

Answer:

C. Walk four times per week

Explanation:

If she wants to increase her time then, she has to walk four times per week.

The total distance covered by any object per unit of time is known as speed. It depends only on the magnitude of the moving object. The unit of speed is a meter/second. The generally considered unit for speed is a meter per second.

The mathematical expression for speed is given by

speed = total distance /Total time

As given in the problem Lyla walks three times per week for 45 minutes at a speed of 4.0 miles per hour. She must walk four times a week if she wants to extend her time.

Thus, the correct answer is option C.

Learn more about speed from here, refer to the link;

brainly.com/question/7359669

#SPJ2

The question is incomplete, the complete question is,

Lyla walks three times per week for 45 minutes at a speed of 4.0 miles per hour. She wants to increase her time. What should she do?

A. Walk at 4.5 miles per hour.

B. Walk for 50 minutes.

C. Walk four times per week.

D. Walk up and down more hills.

Answer:

D

Explanation:

The answer is D because:

A) Only doctors are allowed to prescribe medications.

B) Rita is not a chef/cook.

C) Rita is not a personal trainer

D) The job of a dietican is to provide reccomendations to their clients in order for them to implement a healthy lifestyle via consuming what is best for them.

Hope this helps :)

Answer:

D.) Making recommendations for healthy eating habits

Explanation: PLATO :)))

Answer:

The time she takes to reach the water from when she jumps off the platform is 1.71 s

Explanation:

According to the equations of motion, we have;

v = u - g·t

v² = u² - 2·g·s

s₁ = u₁·t₁ + 1/2·g₁·t₁²

The given parameters are;

The height of the platform (assumption: above the water) = 10 m

The velocity with which she jumps, u = 3 m/s

The acceleration due to gravity, g = 9.81 m/s²

The height to which she jumps, s, is found as follows;

v² = u² - 2·g·s

At maximum height, v = 0, which gives;

0 = 3² - 2×9.81×s

2×9.81×s = 3² = 9

s = 9/(2×9.81) = 0.4587 m

s = 0.4587 m

The time to maximum height, t, is found as follows;

v = u - g·t

0 = 3 - 9.81×t

9.81×t = 3

t = 3/9.81 = 0.3058 s

The total distance, s₁ from maximum height to the water surface = s + 10 = 0.4587 + 10 = 10.4587 m = 10.46 m

The time to reach the water from maximum height, t₁, is found as follows;

s₁ = u₁·t₁ + 1/2·g₁·t₁²

Where;

s₁ =  The total distance from maximum height to the water surface = 10.46 m

u₁ = The initial velocity, this time from the maximum height = 0 m/s

g₁ = The acceleration due to gravity, g (positive this time as the diver is accelerating down) = 9.81 m/s²

t₁ = The time to reach the water from maximum height

Substituting the values gives;

s₁ = u₁·t₁ + 1/2·g₁·t₁²

10.46 = 0·t₁ + 1/2·9.81·t₁²

t₁²= 10.46/(1/2×9.81) = 2.13 s²

t₁ = √2.13  = 1.46 s

Total time = t₁ + t = 1.46 + 0.3058 = 1.7066 ≈ 1.71 s.

Therefore, the time she takes to reach the water from when she jumps off the platform = 1.71 s.

Answer:

The pressure at the bottom of the river is less than that at the bottom of the lake.

Explanation:

From Bernoulli's equation, the pressure difference is given by

ΔP = ρgΔh + ρ(v₂² - v₁²)/2 where ρ = density of water, g = acceleration due to gravity, Δh = depth, v₁ = velocity at top, v₂ = velocity at bottom

For the lake, v₁ = v₂, since the velocity at the top and bottom are the same. So,

ΔP₁ = ρgΔh + ρ(v₁² - v₁²)/2 = ρgΔh + 0 = ρgΔh

P₂ - P₁ = ρgΔh

P₂ = P₁ + ρgΔh

For the river, v₁ < v₂, since the velocity at the top of the river is greater than at the bottom.

So,

ΔP₂ = ρgΔh + ρ(v₂² - v₁²)/2.

Since  v₁ < v₂, ρ(v₂² - v₁²)/2 will be negative,

So,

ΔP₂ = ρgΔh - ρ(v₂² - v₁²)/2.

Since ρ(v₂² - v₁²)/2 is negative, making ΔP less than that in the lake.

So, ΔP₂ = ΔP₁ -  ρ(v₂² - v₁²)/2.

ΔP₂ = P₃ - P₁

P₃ - P₁ = P₂ - P₁ -  ρ(v₂² - v₁²)/2.

P₃ = P₂ - ρ(v₂² - v₁²)/2.

where P₃ = pressure at bottom of the river and P₂ = pressure at bottom of the lake and P₁ = atmospheric pressure at top of river and lake respectively.

Since the factor ρ(v₂² - v₁²)/2 is removed from the pressure at the bottom of the lake, the pressure at the bottom of the river is therefore less than that at the bottom of the lake.

Answer:

$876.96

Explanation:

The energy used is:

3500 W × (24 hr/day) × (120 day) × (1 kW / 1000 W) = 10,080 kWh.

So the cost is:

10,080 kWh × ($0.087 / kWh) = $876.96

Answer:

D

Explanation:

because light has no space nor mass

Answer:

C. Meter

Explanation:

The International System of Unit (SI) is gotten from the french word Systeme international is a modern form of metric measurement. It is the system of measurement that is universally accepted. It is from this SI units that all other system of units are derived. There are seven basic SI units which are:

1) Length in Meter (m)

2) Time in Seconds (s)

3) Amount of Substance in mole (m)

4) Electric current in ampere (A)

5) Temperature in kelvin (k)

6) Luminous intensity in candela (cd)

7) Mass in kilogram (kg)

Answer:

The tension in the rod as the ball moves through the bottom circle is 9.8 N

Explanation:

When the ball is released from rest, the centripetal force equals the weight of the ball. So mv²/r = mg where m = mass of ball = 0.5 kg, v = speed of ball, r = radius of vertical circle = length of rod = 0.5 m and g = acceleration due to gravity = 9.8 m/s²

v = √gr = √9.8 m/s² × 0.5 m = √4.9 = 2.21 m/s

Now at the bottom of the circle T - mg = mv²/r where T = tension in the rod

T = m(g + v²/r)

= m(g + (√gr)²/r)

= m(g+ gr/r)

= m(g + g)

= 2mg

= 2 × 0.5 kg × 9.8 m/s²

= 9.8 N

So, the tension in the rod as the ball moves through the bottom circle is 9.8 N

Answer:

Parachutes

Explanation:

Your parachute allows you to descend more slowly because it lowers terminal velocity by increasing your air resistance. Most parachutes are designed to create a large amount of drag and allow you to land at a safe, low speed.

HOPE THIS HELPS!!!

MARK IT AS BRAINLIEST !!!! ( the crown icon sometimes )

Answer:

The answer is below

Explanation:

The efficiency of a machine is the ratio of its output to its input. The efficiency shows how effective the machine by the way it converts the input energy into work. The higher the efficiency of the machine the more effective it is. The efficiency is usually less than 1.

Given that the machine uses diesel oil (input) that can produce 3.0 x 10⁹ J of energy while the work performed by the machine (output) is 2.7 x 10⁸ J. The efficiency is given as:

Efficiency = output / input = 2.7 x 10⁸ J / 3.0 x 10⁹ J = 0.09 = 9%

This means that the machine is not effective because of its low efficiency

Answer:

Solution

Given:

initial velocity (u)=0m/s (because an object

starts from the rest)

time (t)=3sec

diatance travelled(s)=14m(16-2=14)

acceleration (a)=?

Now,

According to the formula

s=ut+1/2at^2

or,14 =0×3+1/2×a×3^2

or, 14=0+a/2×9

or, 14=9a/2

or, 9a=28

or, a=28/9

or, a=3.1 m/s^2

Therefore, the acceleration of the object is 3.1m/s^2 ans.

Explanation:

The ratio of the areas is the square of the ratio of the radii.

A/A = 3.16² = 9.99

The ratio of the volumes is the cube of the ratio of the radii.

V/V = 3.16³ = 31.6

Answer:

230 = x + 105

x= 125

Explanation:

v = v0 + at

Ignoring the air resistance it will take about 3 seconds for the object to reach the ground.We know that the acceleration due to gravity is 10m/s2.

We also know that the final velocity is 30 m/s while the initial velocity is 0 m/s

we can use the formulae for acceleration to calculate the time taken/

(final - initial velocity)/timetaken=10

(30-0)/timetaken=10

timetaken =30/10=3 seconds

Explanation:

The asked in the Question is missing, although i am assuming the number

as [tex]\frac{6}{23}[/tex] ÷[tex]\frac{\sqrt{2} }{2}[/tex].

The given expression contains an irrational number. So, the quotient will also be an irrational number.

Solving

[tex]\frac{6}{23}\times\frac{\sqrt{2} }{2} \\=\frac{3\sqrt{2} }{23}[/tex]

Which is an irrational number.

Answer:

The spring was compressed the following amount:

[tex]\Delta x=\sqrt{ \frac{m_1\,v_1^2+ m_2\,v_2^2}{k} }[/tex]

Explanation:

Use conservation of energy between initial and final state, considering that the surface id frictionless, and there is no loss in thermal energy due to friction. the total initial energy is the potential energy of the compressed spring (by an amount [tex]\Delta x[/tex]), and the total final energy is the addition of the kinetic energies of both masses:

[tex]E_i=\frac{1}{2} k\,(\Delta x)^2\\\\E_f=\frac{1}{2} m_1\,v_1^2+\frac{1}{2} m_2\,v_2^2[/tex]

[tex]E_i=E_f\\[/tex]

[tex]\frac{1}{2} k\,(\Delta x)^2=\frac{1}{2} m_1\,v_1^2+\frac{1}{2} m_2\,v_2^2\\k\,(\Delta x)^2=m_1\,v_1^2+ m_2\,v_2^2\\(\Delta x)^2=\frac{m_1\,v_1^2+ m_2\,v_2^2}{k} \\\Delta x=\sqrt{ \frac{m_1\,v_1^2+ m_2\,v_2^2}{k} }[/tex]

Answer:

60

Explanation:

According to the given question, the computation of minimum coating thickness is shown below:-

The condition for constructive interference is

[tex]2t_{min} = (m + \frac{1}{2} )\times \frac{\lambda}{^nmateral}[/tex]

[tex]= (0 + \frac{1}{2} )\times \frac{\lambda}{^nmateral}[/tex]

[tex]t = \frac{\lambda}{4n}[/tex]

Now we will put the values to the above formula to reach the answer

[tex]= \frac{480nm}{4\times 2.0}[/tex]

= 60

Therefore we simply applied the above formula to determine the minimum coating thickness

The minimum coating thickness needed to ensure that light of wavelength 480 nm and of perpendicular incidence will be reflected from the two surfaces of the coating with fully constructive interference is 60.

Given that, the index of refraction of glass is 1.50 and the index of refraction of silicon monoxide is 2.00. The wavelength light of 480 nm.

If [tex]\lambda {c}[/tex] is the wavelength in the coating and λ is the wavelength in vacuum, then  [tex]\lambda_{c} = \dfrac {\lambda}{n}[/tex]  where n is the index of refraction of the coating.

Thus, the minimum coating thickness [tex]T_{min}[/tex] can be calculated as,

[tex]2T_{min} = (m+\dfrac {1}{2})\times\dfrac {\lambda} {n}\\\\T_{min} = (m+\dfrac {1}{2}) \times\dfrac {\lambda} {2n}[/tex].

For the constructive interference, m = 0.

So [tex]T_{min} = \dfrac {\lambda} {4n}[/tex]

[tex]T_{min} = \dfrac {480\rm nm} {4\times2.0}[/tex]

[tex]T_{min} = 60[/tex]

The minimum coating thickness needed to ensure that light of wavelength 480 nm and of perpendicular incidence will be reflected from the two surfaces of the coating with fully constructive interference is 60.

For more details, follow the link given below.

https://brainly.com/question/15541641.

Answer:

When we have irregular objects, it may become very hard to calculate the volume of the object, as we actually can not use any simple equation to find it.

The mass is less tricky, just find a scale and wheight it, now we know the mass of the irregular object.

One way to measure the volume of the object is using water... how we do it?

Get some recipient with water, measure the height of the water.

Introduce your object into the water and totally submerge it, now the level of the water will rise. This is because as you introduce the object under the water, you are displacing up a given volume of water that has the same volume as the irregular object.

Now that you know the height of the water before and after you put your object, you can easily calculate the volume of water displaced, and that will be the volume of the object (the tricky part may be totally submerging the object if, for example, is wood and it floats, here you can use a thin wire to push it down but it will affect a little bit the measures.)

Answer:

173psig

Explanation:

The storage cylinder of recovered R-410A is mixture of difluoromethane and pentafluoroethane which is used as a refrigerant in air conditioning application. The refrigeration sector has low temperatures for installation. The pressure of cylinder at 80 F will be 173 psig. The pure refrigerants have inside a container have saturation temperature which is equal to ambient temperature.

A containment canister of recovered r-410a has an estimated pressure of 173psig.

The retrieved R-410A preservation container is a blend of difluoromethane and pentafluoroethane, that is used as a compressor in air conditioning systems.

Assembly conditions in the freezer industry are extremely low. At 80 degrees Fahrenheit, the cylinder pressure will be 173 pounds per square inch.

The specific heat capacity of pure refrigeration systems within a cylinder is the same as the room temperature.

Learn more:

https://brainly.com/question/5793747?referrer=searchResults

Answer;

7.238°

Explanation

From question we know that the grating has 1,970 grooves per centimeter, we can convert to from (cm) to (nm) for unit consistency

The slit separation is expressed below

d=1cm/1970

d=0.0005076

=5076nm

Then the angle (in degrees) that the red light of wavelength 640 nm appear in first order can be calculated using expression below

Sin(x)= mλ/d

Where λ= wavelength=640 nm

d=slit separation

Sin(x)= mλ/d

Sin(x)=(1×640)/5076

=0.126

sin-1(0.126)

X= 7.238°

Therefore,the angle (in degrees) that the red light of wavelength 640 nm appear in first order is 7.238°

Answer:

The atom is mostly empty space.

Explanation:

Ernest Rutherford in the year 1911 developed a model of an atom. In his model the atom was shown that the atom is mostly empty spaces composed of negative electrons which orbits round a positive nucleus just like planets revolving round the sun.

Rutherford came up with this model by performing experiments in 1909 which involves the scattering of alpha particles on a thin gold foil. From this experiments he came up with his model.

Answer:

A!

Explanation:

The atom is mostly empty space.

Answer:

2454.57

Explanation:

Step 1: Solve

[tex]\frac{(8.86+0.001)}{(3.610)(10^{-3}) }[/tex]

[tex]\frac{8.861}{0.003.61 }[/tex]

2454.57

Therefor the answer to this equation is 2454.57

Answer:

White light contains seven colors, which are separated by the prism.

White light reacts with chemicals in the air to produce seven colors.

Explanation:

It was first observed by Sir Issac Newton, that when white light is passed through a prism, an elongated, coloured patch of light is obtained on a screen placed behind the prism. The seven colours obtained constitute the spectrum of white light.

In nature, white light is separated into its constituent wavelengths when white light interacts with substances in the atmosphere.

Answer:

The correct answer is “color is an impurity added to white light by the prism.”

and

“White light contains seven colors, which are separated by the prism

Explanation:

Answer:

6.0×10⁻²¹ J

Explanation:

KE = 3/2 kT,

where KE is average kinetic energy per molecule,

k is the Boltzmann constant,

and T is absolute temperature.

KE = 3/2 (1.38×10⁻²³ J/K) (18 + 273.15) K

KE = 6.0×10⁻²¹ J

Answer:

The answer is 6.0×10⁻²¹ J , because KE = 3/2 kT,  where KE is average kinetic energy per molecule,  k is the Boltzmann constant,  and T is the absolute temperature.

KE = 3/2 (1.38×10⁻²³ J/K) (18 + 273.15) K

KE = 6.0×10⁻²¹ J

your answer is...

C. potassium

Answer:

Stroke has two emissions it could either be the meaning of lightly passing over something with the sense of touch for example stroking a dog/cat

And the medical term stroke where either a person has lost facial features of can't lift their arms up and keep them up or speak properly and their speech would be slurred

Hope this helps

If anything didn't meet your question please comment what you are looking for and I may change my answer thank you :)

Explanation: