a circuit with a ba[ery and a variable resistor is near a loop of wire as shown. when the resistance r is decreased, the induced current in the loop is

The ratio of the low temperature to high temperature of the Carnot engine is 2.38.

The efficiency of the Carnot engine can be defined as the ratio of network done per cycle by the engine to the heat energy absorbed by the engine per cycle by the working substance from the source.

Efficiency = 1 - (Tlow/Thigh)


Heat absorbed by engine = 480J

Heat expelled by engine = 320J

Efficiency of the engine = 56% of efficiency of Carnot engine

The ratio of low temperature to high temperature in the Carnot engine.

Let's assume the efficiency of the Carnot engine is 'ηc' = 1 - T₂/T₁

Where, T₂ = Low temperature and T₁ = High temperature

To calculate the efficiency of the engine given, η = (Q1 - Q2)/Q1

η = (480 - 320)/480

η = 160/480

η = 1/3

η = 33.33%

Now, η = 56% × ηc

0.56ηc = 1/3ηc = (1/3)/0.56 = 0.58

As we already know, ηc = 1 - T₂/T₁

T₂/T₁ = 1 - ηc

T₂/T₁ = 1 - 0.58

T₂/T₁ = 0.42

T₁/T₂ = 1/0.42

T₁/T₂ = 2.38

Therefore, the ratio of low temperature to high temperature in the given Carnot engine with an efficiency of 56% will be about 2.38.

Learn more about Carnot engine here:

https://brainly.com/question/14680478

#SPJ11

Answer:

[tex]\boxed{5427N}[/tex]

Explanation:

We use the well-known equation:

[tex]F=m\cdot a[/tex]

where:

so, we can rewrite the equation like this:

[tex]F= (810kg)(6.7m/s^2)\\F=5427N[/tex]

So, taking into account the statement as seen in the image, your answer must be correct.

[tex]\text{-B$\mathfrak{randon}$VN}[/tex]

Answer: The answer is D. Thermal Energy.

Explanation:

Thermal energy is a type of kinetic energy owing to the fact that it results from the movement of particles.

For a given water velocity (distance traveled per unit time), the greater the cross-sectional area of a stream channel, the lower will be the stream flow (discharge: volume of water per unit time)" is a false statement.

Stream discharge is measured by the volume of water flowing per unit of time, which is calculated by multiplying the stream's cross-sectional area (flow width × flow depth) by its water velocity. As a result, the given statement is false.

According to the formula, an increase in the cross-sectional area of the stream will cause a rise in the stream flow (discharge: volume of water per unit time) because it is multiplied by the velocity. So, for a given water velocity, the greater the cross-sectional area of a stream channel, the higher the stream flow (discharge: volume of water per unit time) will be.

Learn more about Stream discharge here:

https://brainly.com/question/8282980

#SPJ11

a) If the current is running from west to east, the force that our planet's magnetic field exerts on this cord is directed upwards
b) The magnitude of the force that our planet's magnetic field exerts on this cord if it is oriented so that the current in it is running from west to east is F =2.64 x 10^-4 N
c) If the current is running vertically upward, the force that our planet's magnetic field exerts on this cord is directed to the left.  west
d) The magnitude of the force that our planet's magnetic field exerts on this cord if it is oriented so that the current in it is running vertically upward is F = 0 zero
e) If the current is running from north to south, the force that our planet's magnetic field exerts on this cord is directed east.
f) The magnitude of the force that our planet's magnetic field exerts on this cord if it is oriented so that the current in it is running from north to south is F = 2.64 x 10^-4 N
g) The magnetic force is not large enough to cause significant effects under normal household conditions.

EXPLANATION

a) The direction of the force that our planet's magnetic field exerts on the cord is perpendicular to both the direction of the current and the direction of the magnetic field, according to the right-hand rule. In this case, if the current is running from west to east, and the magnetic field is from south to north, the force will be directed upwards.

b) The magnitude of the force can be calculated using the formula:

F = BIL sin(theta)

where B is the magnitude of the magnetic field, I is the current, L is the length of the wire, and theta is the angle between the direction of the current and the direction of the magnetic field. In this case, theta is 90 degrees, so sin(theta) = 1. Substituting the given values, we get:

F = (0.550 x 10^-4 T) x (1.50 A) x (2.40 m) x 1

= 2.64 x 10^-4 N

Therefore, the magnitude of the force is 2.64 x 10^-4 N.

c) If the current in the wire is running vertically upward, the force will be directed towards the west.

d) Using the same formula as in part (b), we can calculate the magnitude of the force:

F = (0.550 x 10^-4 T) x (1.50 A) x (2.40 m) x sin(90)

= 0

Therefore, the magnitude of the force is zero.

e) If the current in the wire is running from north to south, the force will be directed towards the east.

f) Using the same formula as in part (b), we can calculate the magnitude of the force:

F = (0.550 x 10^-4 T) x (1.50 A) x (2.40 m) x 1

= 2.64 x 10^-4 N

Therefore, the magnitude of the force is 2.64 x 10^-4 N.

g) The magnitude of the magnetic force in this case is quite small, and under normal household conditions, it is unlikely to cause significant effects. However, in some situations, such as in electrical power transmission systems, the effects of the magnetic force may need to be taken into account.

For more such questions on magnetic field

https://brainly.com/question/13689629

#SPJ11

The magnetic field at the center of the loop is calculated to be 0.159 T.

The magnetic field at the center of a flat, circular loop with 17 turns, a radius of 12.5 cm, and a current of 0.60 A can be determined by using the equation B = µ₀.n.I/2.π.r, where

Using this equation, the magnetic field at the center of the loop is calculated to be 0.159 T.

Learn more about magnitude of the magnetic field: brainly.com/question/30640184

#SPJ11

Answer:

Bottle                 =               .04

Bottle + Bearing    =            .20

Bottle + Bearing + Water = .24

Bottle + Water =                   .1

Full bottle of water weighs  =  .06

Weight of bearing    =           .16

What volume  of water does the bearing replace????

It takes .14 of bottle to replace bearing leaving .06 of water

Density = 16 / 6 = 2.67

Check:     probably should use volumes

After the helium flash in a star, the core quickly heats up and expands.

A helium flash is the very brief thermal runaway nuclear fusion of significant amounts of helium into carbon during the red giant phase of low mass stars (between 0.8 solar masses (M) and 2.0 M). The centre expands as a result of the core becoming warmer as a result of this.

Following the onset of helium nuclear reactions in a star's core, helium nuclei fuse to create carbon and oxygen.

Most of the time, the stars' positions in reference to one another remain constant. Convergence between Orion and Taurus is ongoing. Ursa Minor is never far from Draco. The stars appear to us as an endless backdrop painting in the sky that hardly moves in reference to one another.

To know more about stars:

https://brainly.com/question/29572549

#SPJ4

If you drop a solid iron ball and a hollow iron ball of the same diameter from the same height at the same time, Aristotle's prediction would be that the solid iron ball will fall faster than the hollow iron ball.

Aristotle, who lived in ancient Greece, believed that heavier objects would fall faster than lighter ones. This was a commonly held belief at the time, but it has since been proven incorrect through scientific experiments.

In reality, when dropped from the same height at the same time, both the solid iron ball and the hollow iron ball of the same diameter would fall at the same rate, neglecting air resistance. This is because the rate at which an object falls is determined by its mass and the force of gravity acting on it, which are the same for both balls.

This was first demonstrated by Galileo Galilei in the late 16th century through his famous experiment involving dropping objects from the Leaning Tower of Pisa. He showed that objects of different masses would fall at the same rate in a vacuum and that air resistance was the primary factor that caused objects to fall at different rates in the real world.

In summary, Aristotle would have predicted that the solid iron ball would fall faster than the hollow iron ball, but this prediction has been shown to be incorrect by scientific experiments.

More on Aristotle can be found here: https://brainly.com/question/5399979

#SPJ1

If the metal sphere is positively charged, then the excess electrons will move to the metal sphere. But if it's negatively charged, the excess electrons will repel the metal sphere.

The expression for the magnitude of the force exerted on the firefighter by the pole can be expressed as  F = mg + ma.  

Where m is the mass of the firefighter,

g is the acceleration due to gravity, and

a is the acceleration of the pole

In order to find an expression for the magnitude of the force, F, exerted on the firefighter by the pole, we need to consider the forces acting on the firefighter.

According to Newton's second law of motion, the force acting on an object is equal to its mass multiplied by its acceleration. In this case, the forces acting on the firefighter are the gravitational force, which is pulling the firefighter downwards with a force of mg, and the force exerted on the firefighter by the pole, which is pushing the firefighter upwards with a force of ma. Therefore, the total force acting on the firefighter is given by the sum of these two forces, which is: F = mg + ma

Thus, this expression gives us the magnitude of the force exerted on the firefighter by the pole. Here, m is the mass of the firefighter, g is the acceleration due to gravity, and a is the acceleration of the pole. if the pole is not accelerating (i.e., if a = 0), then the expression reduces to F = mg, which is the gravitational force acting on the firefighter.

To know more about Magnitude please visit :

https://brainly.com/question/30337362

#SPJ11

The ratio of the man's running speed to the sidewalk's speed is 6.3.

To solve the problem, we can start by using the formula:

distance = speed × time

Let's assume that the length of the moving sidewalk is L, and the speed of the man is v and the speed of the sidewalk is u.

When the man runs along the sidewalk from one end to the other, his speed relative to the ground is (v + u), and the distance he covers is L. Therefore, we have:

L = (v + u) × 2.00 s

When the man runs back along the sidewalk to his starting point, his speed relative to the ground is (v - u), and the distance he covers is also L. Therefore, we have:

L = (v - u) × 12.6 s

Now we can solve for v/u by dividing the two equations:

(v + u)/(v - u) = 2.00/12.6

Solving for v/u gives:

v/u = (2.00/12.6 + 1)/(2.00/12.6 - 1) = 6.3

Therefore, the ratio of the man's running speed to the sidewalk's speed is 6.3.

For more similar questions on distance:

brainly.com/question/12356021

#SPJ11

When an object starts from rest, and it moves in the x direction with a positive velocity, the instantaneous velocity and average velocity are related by the inequality d) "can be larger than, smaller than, or equal to."

The rate at which an object moves in a given direction is known as velocity. It is a vector quantity that has a magnitude and a direction. For example, if an object moves 10 meters to the north in 5 seconds, the velocity is 2 m/s northward.Average velocity and instantaneous velocityInstantaneous velocity is the velocity of an object at a particular instant or point in time. In other words, it's the speed of an object at a specific moment. The average velocity is the total displacement divided by the total time taken for the motion. In other words, it is the total distance covered in a given direction over a specific time period.

The instantaneous velocity and average velocity are related by the inequality that can be larger than, smaller than, or equal to. The instantaneous velocity represents the velocity at a particular moment or point in time, while the average velocity represents the average velocity over a specified time period. The instantaneous velocity and average velocity can be different because the instantaneous velocity is the velocity at a specific moment, whereas the average velocity is the average of all the velocities over a given period of time. Therefore, the instantaneous velocity and average velocity are related by the inequality d) "can be larger than, smaller than, or equal to."

More on velocity: https://brainly.com/question/15721950

#SPJ11

As given, the motorcyclist starts from rest and reaches a speed of 6 m/s

after traveling with uniform acceleration for 3 seconds.

Here, initial velocity u=0

Final velocity v=6 m/s

Time t=3 sec.

Let the acceleration of the motorcycle be a.

On using the equation of motion, v=u+at

6=0+3×a

Or 3a=6

Or a=63

Or a=2 m/s2

→Therefore, the acceleration in a motorcycle is 2 m/s2.←

The absolute temperature is determined by the Kelvin scale, which is the sum of the Celsius temperature and 273.15.

A temperature scale is a system used to measure and quantify the degree of hotness or coldness of an object or substance. It defines a set of numerical values that correspond to specific temperatures, which can be used to compare temperatures and measure changes in temperature over time.

To open the experiment file containing your pressure-temperature data, first launch the Logger Pro software. From there, you can access your file and adjust the graph's axes accordingly. If the data appears to follow a linear relationship, then fit a line to the data by clicking on the Linear Fit option from the Analyze menu. If the data does not appear to follow a linear relationship, take the necessary steps to adjust the graph and obtain a linear relationship.

It is not correct to state that the pressure is proportional to the Celsius temperature. Pressure increases as temperature increases, but it is not a linear relationship. To find the temperature at which the pressure of a gas should drop to zero, you can either manipulate the graph or use the equation to determine the Celsius temperature. Once you have obtained the temperature, compare it to the accepted value for this temperature.

The pressure of a gas is proportional to the absolute temperature of a gas. The absolute temperature is determined by the Kelvin scale, which is the sum of the Celsius temperature and 273.15.

To learn more about the temperature scale follow

https://brainly.com/question/14035602

#SPJ11

The work done on the block by friction during the motion of the block from point A to point B is 2.49 J.

The normal force acting on the block at point A and point B is different. We can find the weight of the block at points A and point B using the following formula:

Weight = mg,

where m is the mass of the block and g is the acceleration due to gravity.

Weight at point A = m × g

Weight at point B = m × g

Now, the normal force acting on the block at point A is given as 3.95 N.

Therefore, we can write the equation for the weight and normal force as:

Weight at point A - Normal force at point A = m × a

Now, at point A, the acceleration acting on the block is the centripetal acceleration a = v²/R where v is the velocity of the block at point A.

We can write the equation for the weight and normal force as:

m × g - 3.95 = m × v²/R

Similarly, at point B, we can write the equation for the weight and normal force as:

m × g - 0.680 = m × v²/R

Now, we can solve both the equations for the velocity of the block at point A and point B:

Velocity at point A, v₁ = √(gR - 3.95/m)

Velocity at point B, v₂ = √(gR - 0.680/m)

The change in kinetic energy during the motion from point A to point B is given by:

∆KE = KE₂ - KE₁

= (1/2)mv₂² - (1/2)mv₁²

We know that work done, W = ∆KE

So, the work done on the block by friction during the motion of the block from point A to point B is given by:

W = (1/2)m(v₂² - v₁²)

Substituting the values in the above equation:

W = (1/2) × 0.0400 × ((√(9.81 × 0.500 - 0.680/0.0400))² - (√(9.81 × 0.500 - 3.95/0.0400))²)

W = 2.49 J

Therefore, the work done on the block by friction is 2.49 J.

Learn more about Friction here:

https://brainly.com/question/24338873

#SPJ11

For the electric flux through a spherical surface is 4.3 x 10⁴ N⋅m²/C, then the net charge enclosed by the surface is μC, and for the electric flux through a cubical box 34 cm on a side is 7.5 x 10³ N⋅m²/C, the total charge enclosed by the box is μC.

The electric flux through a spherical surface is 4.3 x 10⁴ N⋅m²/C.

The net charge is Electric Flux = Charge / Surface Area,

so the net charge enclosed is 4.3 x 10⁴ / (4πr²) where r is the radius of the sphere.

Therefore, the net charge enclosed by the surface is μC.

The electric flux through a cubical box 34 cm on a side is 7.5 x 10³ N⋅m²/C.

The total charge is Electric Flux = Charge / Surface Area,

so the total charge enclosed is 7.5 x 10³ / (6a²)

where a is the length of one side of the cube.

Therefore, the total charge enclosed by the box is μC.

Learn more about electric flux here:

https://brainly.com/question/2664005

#SPJ11

In a conservative system, the total energy is conserved, which means that the initial energy (ei) is equal to the final energy (ef).

Conservative systems are those where the total energy remains constant over time, such as in a pendulum swinging back and forth or a planet orbiting a star under the influence of gravity.

In such systems, the energy can be converted from one form to another, but the total amount of energy remains constant.

Therefore, we can say that in a conservative system, the initial energy (ei) and the final energy (ef) are equal. This means that any changes in the system's energy, such as potential energy being converted into kinetic energy, must be balanced by an equal and opposite change in some other form of energy, such as potential energy being converted into kinetic energy.

Learn more about conservation of energy here: https://brainly.com/question/166559

#SPJ1

Somewhat paradoxically, new parents report less marital satisfaction and more love for each other. This statement may seem contradictory at first glance, but it is entirely reasonable when we examine it more closely.

Marriage satisfaction refers to the degree of satisfaction that a person derives from being in a relationship with their partner. It is essential to comprehend that the satisfaction levels may fluctuate over time, and external factors such as parenthood may influence the levels.

Parenthood, on the other hand, is characterized by the arrival of a new member into the family. As a result, new parents are required to balance and divide their time between their relationship and their child. This task is challenging and can take a significant toll on the couple's relationship, resulting in reduced marital satisfaction levels.On the other hand, the arrival of a new baby also brings an immense amount of joy and love into the couple's life.

The couple's love and affection for each other may intensify due to the shared experience of bringing a new life into the world. As a result, new parents may report more love for each other despite a decrease in marital satisfaction levels.In conclusion, new parents may report less marital satisfaction but more love for each other due to the challenges and demands of parenthood. Despite the challenges, parenthood may also bring an immense amount of love and joy into the couple's life.

for such more questions on paradoxically

https://brainly.com/question/31218828

#SPJ11

The maximum acceleration that the student can achieve with the 1500 kg suitcase is 50N/1500kg = 0.033 m/s2.

Acceleration is the change in velocity per unit time. Acceleration is a vector quantity that has both magnitude and direction. Acceleration is divided into deceleration acceleration and acceleration acceleration. Acceleration decreases meaning the direction of acceleration is opposite to the direction of velocity.

To calculate the maximum acceleration, we can use the following equation:
Force = Mass x Acceleration. Therefore, 50N = 1500kg x Acceleration

Solving for Acceleration, we get 50N/1500kg = 0.033 m/s2.

Learn more about acceleration : brainly.com/question/20595261

#SPJ11

A ball is thrown upwards and caught when it comes back down. In the presence of air resistance, the speed with which it is caught is C. less than the speed it had when thrown upwards.

When a ball is thrown upwards, it gains kinetic energy due to the force exerted by the thrower. Then, as it ascends, it loses kinetic energy and gains potential energy as it moves higher up. Finally, the ball comes to a stop, its kinetic energy becoming zero, and its potential energy reaches its maximum value. At the top, the ball begins to fall back to the ground.The air resistance opposes the motion of the ball, slowing it down as it travels upwards.

When the ball starts coming back down, the air resistance exerts an additional force, which slows down the ball and reduces its speed. As a result, the speed with which it is caught is less than the speed it had when thrown upwards. Hence, option (C) is correct.

Learn more about kinetic energy at:

https://brainly.com/question/22174271

#SPJ11

Wood will still be an effective insulator. when the temperature of the wood reaches an extreme level.

Compared to materials like metals, marble, glass, and concrete, wood has a low thermal conductivity (high capacity to absorb heat). The axial direction of thermal conductivity is highest, and it rises with density and moisture content, making light, dry woods better insulators.

Insulators are substances that hinder the easy passage of electricity. Plastic, wood, and rubber are among the most insulating nonmetal materials.

Typically, wood has a perpendicular to the grain heat conductivity of between 0.1 and 0.2 W/mK.

It begins to pyrolyze when the temperature rises. Either the materials' internal structure retains the decomposition products, or they release them as gases. When gaseous substances interact with oxygen and each other, a lot of heat is produced. This additional heat promotes pyrolysis and combustion reactions.

Learn more about Insulator here:

https://brainly.com/question/2619275

#SPJ4

EER is defined as the Energy Efficiency Ratio which is the ratio of cooling capacity in BTU/hr to the power input in watts.

The EER of the given 8000 Btu/h air conditioner is 5.33 Btu/hour per watt.

In the case of the given 8000 Btu/h air conditioner that requires a power input of 1500 W, the EER can be calculated as follows:

EER = (cooling capacity in Btu/hr) / (power input in watts)

EER = 8000 Btu/hour / 1500 W = 5.33 Btu/hour per wat.

Energy efficiency ratio (EER) is used in the USA and is defined as the system output in Btu/h per watt of electrical energy.

Coefficient of performance (COP) is the equivalent measure using SI units, which is widely used in the UK. A COP of 1.0 equates to an EER of 3.4.

To know more about power:https://brainly.com/question/11569624

#SPJ11

In the context of research evidence from the study conducted by Williams and McCririe, both central and peripheral vision operate when a person picks up information critical to catching an object.

What is vision?

Vision is the sense that allows us to recognize and understand the physical world around us. Our brains then receive this information and convert it into the pictures that we see with our eyes.

Vision is the term used to describe the ability to see things with our eyes, such as color, form, and movement.

In the context of research evidence from the study conducted by Williams and McCririe, both central and peripheral vision operate when a person picks up information critical to catching an object.

Their research found that peripheral vision was essential to athletes performing in certain sports such as cricket, soccer, and baseball.

Peripheral vision, as well as central vision, are critical components of efficient eye tracking and hand-eye coordination.

Learn more about vision here:

https://brainly.com/question/4269555

#SPJ11

The frequency that the bad guy hear is 12000 hz when the police car is moving with speed of 80m/s.

For more information on doppler effect kindly visit to

https://brainly.com/question/15318474

#SPJ1

When the 35.0-g bullet moving at 475 m/s strikes the 4.4-kg bag of flour, the momentum of the bullet is transferred to the bag of flour, causing the bag of flour to move and the bag moving when the bullet exits at 91.3 m/s.

We can calculate the velocity of the bag of flour after the collision using conservation of momentum:

Here we have the following data as :

Momentum of bullet before collision = Momentum of bullet and bag after collision

m bullet × v bullet, before = (m bullet + m bag) bag × v bag, after

We can solve for v bag ,after:

v bag ,after = (m bullet × v bullet, before) / (m bullet + m bag)

v bag, after = (35.0 g × 475 m/s) / (35.0 g + 4.4 kg) = 91.3 m/s

Therefore, the bag of flour is moving at 91.3 m/s when the bullet exits.

Read more about mass here:

https://brainly.com/question/1838164

#SPJ11

The equations for the balance of forces in the horizontal and vertical directions for Block A and Block B are:                                                                    Horizontal direction of Block A: T = 12.5 N,Vertical direction of Block A: W = 24.5 N,Horizontal direction of Block B: T = 22.5 N and Vertical direction of Block B: W = 44.1 N.

The forces acting on Block A are: Force of tension (T) and Force of gravity (W).The forces acting on Block B are: Force of tension (T) and Force of gravity (W).For Block A in the horizontal direction, the force exerted will be the force of tension (T).

Therefore: Horizontal direction of Block A: T = mA a ………………….. (1)           For Block A in the vertical direction, the force exerted will be the force of gravity (W).                                                      

Therefore: Vertical direction of Block A: W = mA g ………………….. (2)              For Block B in the horizontal direction, the force exerted will also be the force of tension (T).                                              

Therefore: Horizontal direction of Block B: T = mB b ………………….. (3)            For Block B in the vertical direction, the force exerted will be the force of gravity (W).                                                              

 Therefore: Vertical direction of Block B: W = mB g ………………….. (4)

The equations can be solved by substituting the values of the masses and the acceleration due to gravity. Therefore, equations (1) to (4) will become:

Horizontal direction of Block A: T = 2.5 (5) = 12.5 N                                       Vertical direction of Block A: W = 2.5 (9.8) = 24.5 N                                        Horizontal direction of Block B: T = 4.5 (5) = 22.5 N                                     Vertical direction of Block B: W = 4.5 (9.8) = 44.1 N

Therefore, the equations for the balance of forces in the horizontal and vertical directions for Block A and Block B are:

Horizontal direction of Block A: T = 12.5 N                                                        Vertical direction of Block A: W = 24.5 N                                                         Horizontal direction of Block B: T = 22.5 N                                                     Vertical direction of Block B: W = 44.1 N

More on forces: https://brainly.com/question/14932990

#SPJ11

When using compass orientation, migrating animals make use of the sun, stars, and Earth's magnetic field to navigate. So, option d is correct option.

Compass orientation in migrating animals is the process of using the sun, stars, and Earth's magnetic field to navigate. Migrating animals use a variety of techniques to navigate, depending on their species and environment.

Some animals use the position of the sun, stars, and Earth's magnetic field as their primary means of orientation when migrating. This is known as compass orientation.

Compass orientation is a technique that relies on environmental cues, such as the position of the sun and stars, to determine direction. Some animals can use the Earth's magnetic field to navigate as well. This is known as magnetic orientation.

Magnetic orientation is used by some species of birds and fish, as well as certain insects and reptiles. Other animals use landmarks and olfactory cues to navigate.

These animals rely on visual or chemical markers in the environment to orient themselves. This technique is known as piloting. Piloting is used by animals such as rodents, bats, and some species of birds. Animals that use piloting must be able to remember and recognize the landmarks they use as cues to navigate.

Finally, some animals use memories from previous trips with parents to navigate. This technique is known as true navigation. True navigation requires animals to have a highly developed sense of spatial awareness and memory. True navigation is used by animals such as sea turtles and some species of birds.

All of these techniques require different cognitive abilities and sensory mechanisms, but they allow animals to navigate over long distances to reach their desired destinations.

for similar question on magnetic field to navigate.

https://brainly.com/question/22986969

#SPJ11

18.75 m/s² is the acceleration brought on by gravity on the unidentified planet.

9.8 m/s2 is the acceleration caused by gravity at or close to the surface of the Earth. The force of gravity causes items to fall towards the ground.

The acceleration brought on by gravity on the unidentified planet may be calculated using the equation of motion for a falling object:

d = 1/2 * g * t²

where d is the object's displacement, g is the acceleration brought on by gravity, and t is the passing of time.

This equation can be changed in order to account for g:

g = 2 * d / t²

Plugging in the given values:

d = 1.5 m

t = 0.4 s

g = 2 * 1.5 m / (0.4 s)²

g = 18.75 m/s²

To know more about acceleration visit:-

https://brainly.com/question/30660316

#SPJ1

The correct comparison of the energy generation processes is "The Sun generates energy by fusing small nuclei into larger ones, while our power plants generate energy by the fission (splitting) of large nuclei". Thus, the correct options are A and B.

Nuclear reactions involve the alteration of an atom's nucleus in both cases. Nuclear power plants and the sun both use energy generated by these nuclear reactions to produce electricity. The difference is in the type of nuclear reaction that takes place.

In the Sun, nuclear fusion is the process by which atomic nuclei of low atomic number fuse to form a heavier nucleus with the release of energy. The energy produced in this way is what makes the Sun so hot and bright. In a nuclear power plant, nuclear fission is the process by which the nucleus of an atom is split into two smaller nuclei.

The energy that is released in the process is used to heat water, creating steam that drives a turbine, which in turn drives a generator to produce electricity.

Therefore, the correct options are A and B.

Learn more about Nuclear power here:

https://brainly.com/question/18769119

#SPJ11