A clown 2 m tall looks at himself in a full-length mirror (floor-to-ceiling). Where in the mirror must he look to see his feet?

Answers

Answer 1

Answer:

Around the center of the mirror


Related Questions

A mass M is attached to an ideal massless spring. When this system is set in motion with amplitude A, it has a period T. What is the period if the amplitude of the motion is doubled

Answers

Answer:

The period of the motion will still be equal to T.

Explanation:

for a system with mass = M

attached to a massless spring.

If the system is set in motion with an amplitude (distance from equilibrium position) A

and has period T

The equation for the period T is given as

[tex]T = 2\pi \sqrt{\frac{M}{k} }[/tex]

where k is the spring constant

If the amplitude is doubled, the distance from equilibrium position to the displacement is doubled.

Increasing the amplitude also increases the restoring force. An increase in the restoring force means the mass is now accelerated to cover more distance in the same period, so the restoring force cancels the effect of the increase in amplitude. Hence, increasing the amplitude has no effect on the period of the mass and spring system.

If a vacuum pump reduces the pressure of a gas to 1.0 x 10-6 atm, what is the pressure expressed in millimeters of mercury

Answers

Answer:

[tex]1.0\times 10^{-6}[/tex] atmospheres are equivalent to [tex]7.6\times 10^{-4}[/tex] millimeters of mercury.

Explanation:

According to current SI unit conversions, 1 atmosphere is equal to 760 millimeters of mercury. The current pressure is determined by simple rule of three:

[tex]p = \frac{760\,mm\,Hg}{1\,atm} \times (1\times 10^{-6}\,atm)[/tex]

[tex]p = 7.6\times 10^{-4}\,mm\,Hg[/tex]

[tex]1.0\times 10^{-6}[/tex] atmospheres are equivalent to [tex]7.6\times 10^{-4}[/tex] millimeters of mercury.

a person Travels along a straight road for half the distance with velocity V1 and the remaining half the distance with velocity V2 the average velocity is given by​

Answers

Answer: (V1+V2)/2

Explanation: This is because basically with the question they are trying to say u(initial velocity) is V1 and v(final velocity) is V2 as the journey starts off with V1 and ends with V2 so therefore we know an equation where average velocity=(u+v)/2. So here it’s (V1+V2)/2

Structures on a bird feather act like a diffraction grating having 8500 lines per centimeter. What is the angle of the first-order maximum for 577 nm light shone through a feather?

Answers

Answer:

29.5°

Explanation:

To find the distance d

d = 1E10^-2/8500lines

= 1.17x 10-6m

But wavelength in first order maximum is 577nm

and M = 1

So

dsin theta= m. Wavelength

Theta= sin^-1 (m wavelength/d)

= Sin^-1 ( 1* 577 x10^-8m)/1.17*10^-6

= 493*10^-3= sin^-1 0.493

Theta = 29.5°

A speeding car has a velocity of 80 mph; suddenly it passes a cop car but does not stop. When the speeding car passes the cop car, the cop immediately accelerates his vehicle from 0 to 90 mph in 4.5 seconds. The cop car has a maximum velocity of 90 mph. At what time does the cop car meet the speeding car and at what distance?

Answers

Answer:

Distance= 4 miles

Time = 36.3 seconds

Explanation:

80 mph = 178.95 m/s

90 mph = 201.32 m/s

V = u +at

201.32= 0+a(4.5)

201.32/4.5= a

44.738 m/s² = a

Acceleration of the cop car

= 44.738 m/s²

Distance traveled at 4.5seconds

For the cop car

S= ut + ½at²

S= 0(4.5) + ½*44.738*4.5

S= 100.66 meters

Distance traveled at 4.5seconds

For the speeding car

4.5*178.95=805.275

The cop car will still cover 704.675 +x distance while the speeding car covers for their distance to be equal

X/178.95= (704.675+x)/201.32

X-0.89x= 626.37

0.11x= 626.37

X= 5694.3 meters

The time = 5694.3/178.95

Time =31.8 seconds

So the distance they meet

= 5694.3+805.275

= 6499.575 meters

= 4.0 miles

The Time = 4.5+31.8

Time = 36.3 seconds


What characteristic makes Biology a science, but not Art History?
Using a process of testing ideas and gathering evidence
o Writing books about the subject
O Having a college degree to study it
Discussing and sharing ideas​

Answers

Using a process of testing ideas and gathering evidence.

Answer:

 

Using a process of testing ideas and gathering evidence

Explanation:

When a monochromatic light of wavelength 433 nm incident on a double slit of slit separation 6 µm, there are 5 interference fringes in its central maximum. How many interference fringes will be in the central maximum of a light of wavelength 632.9 nm for the same double slit?

Answers

Answer:

The number of interference fringes is  [tex]n = 3[/tex]

Explanation:

From the question we are told that

     The wavelength is  [tex]\lambda = 433 \ nm = 433 *10^{-9} \ m[/tex]

      The distance of separation is  [tex]d = 6 \mu m = 6 *10^{-6} \ m[/tex]

       The  order of maxima is m =  5

       

The  condition for constructive interference is

       [tex]d sin \theta = n \lambda[/tex]

=>     [tex]\theta = sin^{-1} [\frac{5 * 433 *10^{-9}}{ 6 *10^{-6}} ][/tex]

=>    [tex]\theta = 21.16^o[/tex]

So at  

      [tex]\lambda_1 = 632.9 nm = 632.9*10^{-9} \ m[/tex]

   [tex]6 * 10^{-6} * sin (21.16) = n * 632.9 *10^{-9}[/tex]

=>    [tex]n = 3[/tex]

   

A resistor and an inductor are connected in series to an ideal battery of constant terminal voltage. At the moment contact is made with the battery, the voltage across the inductor is

Answers

Answer:

The voltage is equal to the batteries terminal voltage

Explanation:

Explanation:

A spring attached to the ceiling is stretched 2.45 meters by a four kilogram mass. If the mass is set in motion in a medium that imparts a damping force numerically equal to 16 times the velocity, the correct differential equation for the position x (t ), of the mass at a function of time, t is

Answers

Answer:

d²x/dt² = - 4dx/dt - 4x is the required differential equation.

Explanation:

Since the spring force F = kx where k is the spring constant and x its extension = 2.45 equals the weight of the 4 kg mass,

F = mg

kx = mg

k = mg/x

= 4 kg × 9.8 m/s²/2.45 m

= 39.2 kgm/s²/2.45 m

= 16 N/m

Now the drag force f = 16v where v is the velocity of the mass.

We now write an equation of motion for the forces on the mass. So,

F + f = ma (since both the drag force and spring force are in the same direction)where a = the acceleration of the mass

-kx - 16v = 4a

-16x - 16v = 4a

16x + 16v = -4a

4x + 4v = -a where v = dx/dt and a = d²x/dt²

4x + 4dx/dt = -d²x/dt²

d²x/dt² = - 4dx/dt - 4x which is the required differential equation

A cook preparing a meal for a group of people is an example of
O kinetic energy because he has the ability to make a meal
O potential energy because he has the ability to make a meal
O kinetic energy because he is making the meal
o potential energy because he is making the meal​

Answers

The third point is the correct answer because it’s happening now and kinetic energy is energy possessed by a moving object.

Hope this helps ya

There are 5510 lines per centimeter in a grating that is used with light whose wavelegth is 467 nm. A flat observation screen is located 1.03 m from the grating. What is the minimum width that the screen must have so the centers of all the principal maxima formed on either side of the central maximum fall on the screen

Answers

Answer:

1.696 nm

Explanation:

For a diffraction grating, dsinθ = mλ where d = number of lines per metre of grating = 5510 lines per cm = 551000 lines per metre and λ = wavelength of light = 467 nm = 467 × 10⁻⁹ m. For a principal maximum, m = 1. So,

dsinθ = mλ = (1)λ = λ

dsinθ = λ

sinθ = λ/d.

Also tanθ = w/D where w = distance of center of screen to principal maximum and D = distance of grating to screen = 1.03 m

From trig ratios 1 + cot²θ = cosec²θ

1 + (1/tan²θ) = 1/(sin²θ)

substituting the values of sinθ and tanθ we have

1 + (D/w)² = (d/λ)²

(D/w)² = (d/λ)² - 1

(w/D)² = 1/[(d/λ)² - 1]

(w/D) = 1/√[(d/λ)² - 1]

w = D/√[(d/λ)² - 1] = 1.03 m/√[(551000/467 × 10⁻⁹ )² - 1] = 1.03 m/√[(1179.87 × 10⁹ )² - 1] = 1.03 m/1179.87 × 10⁹  = 0.000848 × 10⁻⁹ = 0.848 × 10⁻¹² m = 0.848 nm.

w is also the distance from the center to the other principal maximum on the other side.

So for both principal maxima to be on the screen, its minimum width must be 2w = 2 × 0.848 nm = 1.696 nm

So, the minimum width of the screen must be 1.696 nm

In a two-slit experiment, the slit separation is 3.34 ⋅ 10 − 5 m. The interference pattern is created on a screen that is 3.30 m away from the slits. If the 7th bright fringe on the screen is 29.0 cm away from the central fringe, what is the wavelength of the light?

Answers

Answer:

The wavelength is  [tex]\lambda = 419 \ nm[/tex]

Explanation:

From the question we are told that

   The  distance of separation is   [tex]d = 3.34 *10^{-5} \ m[/tex]

   The  distance of the screen is  [tex]D = 3.30 \ m[/tex]

      The  order of the fringe is  n =  7

     The distance of separation of  fringes is y =  29.0 cm = 0.29 m

   

Generally the wavelength of the light is mathematically represented as

          [tex]\lambda = \frac{y * d }{ n * D}[/tex]

substituting values

         [tex]\lambda = \frac{0.29 * 3.34*10^{-5} }{ 7 * 3.30}[/tex]

        [tex]\lambda = 4.19*10^{-7}\ m[/tex]

        [tex]\lambda = 419 \ nm[/tex]

When using science to investigate physical phenomena, which characteristic of the event must exist? predictable repeatable provable readable

Answers

Answer:

Not sure but I believe predictable.

Explanation:

Phenomena usually consists of :

- A history, a date in which the physical phenomenon has occurred.

- A source, a place or reason to why or where the physical phenomena has occured.

According to this, I want to say predictable.

It is not repeatable, there are one-time phenomenons that have occurred that scientists to this day still have not recorded again such as the Big Bang.

It is not provable. Most of the theories earlier scientists and historians have predicted have not yet been proved. Yet rather, somehow, they have been explored and investigated.

It is not readable. This is self explanatory, some things scientists investigate are not written down, nor read. It starts with a mental theory and then immediately goes to the next phase of investigation.

When the current in a toroidal solenoid is changing at a rate of 0.0200 A/s, the magnitude of the induced emf is 12.7 mV. When the current equals 1.50 A, the average flux through each turn of the solenoid is 0.00458 Wb. How many turns does the solenoid have?

Answers

Answer:

[tex]N = 208 \ turns[/tex]

Explanation:

From the question we are told that

    The  rate of  current change is  [tex]\frac{di }{dt} = 0.0200 \ A/s[/tex]

    The  magnitude of the induced emf is  [tex]\epsilon = 12.7 \ mV = 12.7 *10^{-3} \ V[/tex]

     The  current is  [tex]I = 1.50 \ A[/tex]

      The  average  flux is  [tex]\phi = 0.00458 \ Wb[/tex]

Generally the number of  turns the number of turn the solenoid has is mathematically represented as  

            [tex]N = \frac{\epsilon_o * I}{ \phi * \frac{di}{dt} }[/tex]

substituting values

           [tex]N = \frac{ 12.7*10^{-3} * 1.50 }{ 0.00458 * 0.0200 }[/tex]

            [tex]N = 208 \ turns[/tex]

       

c) If the ice block (no penguins) is pressed down even with the surface and then released, it will bounce up and down, until friction causes it to settle back to the equilibrium position. Ignoring friction, what maximum height will it reach above the surface

Answers

Answer:

y = 20.99 V / A

there is no friction    y = 20.99 h

Explanation:

Let's solve this exercise in parts: first find the thrust on the block when it is submerged and then use the conservation of energy

when the block of ice is submerged it is subjected to two forces its weight  hydrostatic thrust

         

              F_net= ∑F = B-W

the expression stop pushing is

              B = ρ_water g V_ice

where rho_water is the density of pure water that we take as 1 10³ kg / m³ and V is the volume d of the submerged ice

We can write the weight of the body as a function of its density rho_hielo = 0.913 10³ kg / m³

             W = ρ-ice g V

              F_net = (ρ_water - ρ_ ice) g V

this is the net force directed upwards, we can find the potential energy with the expression

            F = -dU / dy

            ΔU = - ∫ F dy

            ΔU = - (ρ_water - ρ_ ice) g ∫ (A dy) dy

            ΔU = - (ρ_water - ρ_ ice) g A y² / 2

we evaluate between the limits y = 0,  U = 0, that is, the potential energy is zero at the surface

             U_ice = (ρ_water - ρ_ ice) g A y² / 2

now we can use the conservation of mechanical energy

starting point. Ice depth point

             Em₀ = U_ice = (ρ_water - ρ_ ice) g A y² / 2

final point. Highest point of the block

             [tex]Em_{f}[/tex] = U = m g y

as there is no friction, energy is conserved

            Em₀ = Em_{f}

            (ρ_water - ρ_ ice) g A y² / 2 = mg y

let's write the weight of the block as a function of its density

            ρ_ice = m / V

            m = ρ_ice V

we substitute

             (ρ_water - ρ_ ice) g A y² / 2 = ρ_ice V g y

              y = ρ_ice / (ρ_water - ρ_ ice) 2 V / A

let's substitute the values

             y = 0.913 / (1 - 0.913) 2 V / A

             y = 20.99 V / A

This is the height that the lower part of the block rises in the air, we see that it depends on the relationship between volume and area, which gives great influence if there is friction, as in this case it is indicated that there is no friction

                V / A = h

where h is the height of the block

                 y = 20.99 h

) Calculate current passing in an electrical circuit if you know that the voltage is 8 volts and the resistance is 10 ohms

Answers

Explanation:

Hey, there!

Here, In question given that,

potential difference (V)= 8V

resistance (R)= 10 ohm

Now,

According to the Ohm's law,

V= R×I { where I = current}

or, I = V/R

or, I = 8/10

Therefore, current is 4/5 A or 0.8 A.

(A= ampere = unit of current).

Hope it helps...

A diffraction grating 19.2 mm wide has 6010 rulings. Light of wavelength 337 nm is incident perpendicularly on the grating. What are the (a) largest, (b) second largest, and (c) third largest values of θ at which maxima appear on a distant viewing screen?

Answers

Answer:

(a). The largest value of θ is 71.9°.

(b). The second largest value of θ is 57.7°.

(c). The third largest value of θ is 47.7° .

Explanation:

Given that,

Width of diffraction grating [tex]w= 19.2\ mm[/tex]

Number of rulings[tex]N=6010[/tex]

Wavelength = 337 nm

We need to calculate the distance between adjacent rulings

Using formula of distance

[tex]d=\dfrac{w}{N}[/tex]

Put the value into the formula

[tex]d=\dfrac{19.2\times10^{-3}}{6010}[/tex]

[tex]d=3.19\times10^{-6}\ m[/tex]

We need to calculate the value of m

Using formula of constructive interference

[tex]d \sin\theta=m\lambda[/tex]

[tex]\sin\theta=\dfrac{m\lambda}{d}[/tex]

Here, m = 0,1,2,3,4......

[tex]\lambda[/tex]=wavelength

For largest value of  θ

[tex]\dfrac{m\lambda}{d}>1[/tex]

[tex]m>\dfrac{d}{\lambda}[/tex]

Put the value into the formula

[tex]m>\dfrac{3.19\times10^{-6}}{337\times10^{-9}}[/tex]

[tex]m>9.46[/tex]

[tex]m = 9[/tex]

(a). We need to calculate the largest value of θ

Using formula of constructive interference

[tex]\theta=\sin^{-1}(\dfrac{m\lambda}{d})[/tex]

Now, put the value of m in to the formula

[tex]\theta=\sin^{-1}(\dfrac{9\times337\times10^{-9}}{3.19\times10^{-6}})[/tex]

[tex]\theta=71.9^{\circ}[/tex]

(b). We need to calculate the second largest value of θ

Using formula of constructive interference

[tex]\theta=\sin^{-1}(\dfrac{m\lambda}{d})[/tex]

Now, put the value of m in to the formula

[tex]\theta=\sin^{-1}(\dfrac{8\times337\times10^{-9}}{3.19\times10^{-6}})[/tex]

[tex]\theta=57.7^{\circ}[/tex]

(c). We need to calculate the third largest value of θ

Using formula of constructive interference

[tex]\theta=\sin^{-1}(\dfrac{m\lambda}{d})[/tex]

Now, put the value of m in to the formula

[tex]\theta=\sin^{-1}(\dfrac{7\times337\times10^{-9}}{3.19\times10^{-6}})[/tex]

[tex]\theta=47.7^{\circ}[/tex]

Hence, (a). The largest value of θ is 71.9°.

(b). The second largest value of θ is 57.7°.

(c). The third largest value of θ is 47.7° .

W is the work done on the system, and K, U, and Eth are the kinetic, potential, and thermal energies of the system, respectively. Any energy not mentioned in the transformation is assumed to remain constant; if work is not mentioned, it is assumed to be zero.

1. Give a specific example of a system with the energy transformation shown.
W→ΔEth

2. Give a specific example of a system with the energy transformation shown.

a. Rolling a ball up a hill.
b. Moving a block of wood across a horizontal rough surface at constant speed.
c. A block sliding on level ground, to which a cord you are holding on to is attached .
d. Dropping a ball from a height.

Answers

Answer:

1) a block going down a slope

2) a) W = ΔU + ΔK + ΔE, b) W = ΔE, c)  W = ΔK, d) ΔU = ΔK

Explanation:

In this exercise you are asked to give an example of various types of systems

1) a system where work is transformed into internal energy is a system with friction, for example a block going down a slope in this case work is done during the descent, which is transformed in part kinetic energy, in part power energy and partly internal energy that is represented by an increase in the temperature of the block.

2)

a) rolling a ball uphill

In this case we have an increase in potential energy, if there is a change in speed, the kinetic energy also increases, if the change in speed is zero, there is no change in kinetic energy and there is a change in internal energy due to the stationary rec in the point of contact

 W = ΔU + ΔK + ΔE

b) in this system work is transformed into internal energy

      W = ΔE

c) There is no friction here, therefore the work is transformed into kinetic energy

    W = ΔK

d) if you assume that there is no friction with the air, the potential energy is transformed into kinetic energy

      ΔU = ΔK

A certain car traveling 33.0mph skids to a stop in 39m from the point where the brakes were applied. In approximately what distance would the car stop had it been going 66.0mph

Answers

Answer: 156.02 metre.

Explanation:

Give that a certain car traveling 33.0mph skids to a stop in 39m from the point where the brakes were applied.

Let us use third equation of motion,

V^2 = U^2 + 2as

Since the car is decelerating, V = 0

And acceleration a will be negative.

U = 33 mph

S = 39 m

Substitute both into the formula

0 = 33^2 - 2 × a × 39

0 = 1089 - 78a

78a = 1089

a = 1089 / 78

a = 13.96 m/h^2

If we assume that the car decelerate at the same rate.

the distance the car will stop had it been going 66.0mph will be achieved by using the same formula

V^2 = U^2 + 2as

0 = 66^2 - 2 × 13.96 × S

4356 = 27.92S

S = 4356 / 27.92

S = 156.02 m

Therefore, the car would stop at

156.02 m

A circular loop in the plane of a paper lies in a 0.45 T magnetic field pointing into the paper. The loop's diameter changes from 17.0 cm to 6.0 cm in 0.53 s.
A) Determine the direction of the induced current.
B) Determine the magnitude of the average induced emf.
C) If the coil resistance is 2.5 Ω, what is the average induced current?

Answers

Answer:

(A). The direction of the induced current will be clockwise.

(B). The magnitude of the average induced emf 16.87 mV.

(C). The induced current is 6.75 mA.

Explanation:

Given that,

Magnetic field = 0.45 T

The loop's diameter changes from 17.0 cm to 6.0 cm .

Time = 0.53 sec

(A). We need to find the direction of the induced current.

Using Lenz law

If the direction of magnetic field shows into the paper then the direction of the induced current will be clockwise.

(B). We need to calculate the magnetic flux

Using formula of flux

[tex]\phi_{1}=BA\cos\theta[/tex]

Put the value into the formula

[tex]\phi_{1}=0.45\times(\pi\times(8.5\times10^{-2})^2)\cos0[/tex]

[tex]\phi_{1}=0.01021\ Wb[/tex]

We need to calculate the magnetic flux

Using formula of flux

[tex]\phi_{2}=BA\cos\theta[/tex]

Put the value into the formula

[tex]\phi_{2}=0.45\times(\pi\times(3\times10^{-2})^2)\cos0[/tex]

[tex]\phi_{2}=0.00127\ Wb[/tex]

We need to calculate the magnitude of the average induced emf

Using formula of emf

[tex]\epsilon=-N(\dfrac{\Delta \phi}{\Delta t})[/tex]

Put the value into t5he formula

[tex]\epsilon=-1\times(\dfrac{0.00127-0.01021}{0.53})[/tex]

[tex]\epsilon=0.016867\ V[/tex]

[tex]\epsilon=16.87\ mV[/tex]

(C). If the coil resistance is 2.5 Ω.

We need to calculate the induced current

Using formula of current

[tex]I=\dfrac{\epsilon}{R}[/tex]

Put the value into the formula

[tex]I=\dfrac{0.016867}{2.5}[/tex]

[tex]I=0.00675\ A[/tex]

[tex]I=6.75\ mA[/tex]

Hence, (A). The direction of the induced current will be clockwise.

(B). The magnitude of the average induced emf 16.87 mV.

(C). The induced current is 6.75 mA.

Scouts at a camp shake the rope bridge they have just crossed and observe the wave crests to be 9.70 m apart. If they shake the bridge twice per second, what is the propagation speed of the waves (in m/s)?

Answers

Answer:

The speed of the wave is 19.4 m/s

Explanation:

The wave's crest to crest distance (the wavelength of this rope's wave) λ= 9.70 m

The bridge is shaken twice, meaning that two wavelengths passed a given point on the rope per sec. The frequency of a wave is the amount of that wave that passes a given point in a second.

this means that the frequency f = 2 Hz

The speed of a wave = fλ = 9.70 x 2 = 19.4 m/s

A straight wire that is 0.56 m long is carrying a current of 2.6 A. It is placed in a uniform magnetic field, where it experiences a force of 0.24 N. The wire makes an angle of 900 with the magnetic field. What is the magnitude of the magnetic field

Answers

Answer:

0.165Tesla

Explanation:

The Force experienced by the wire in the uniform magnetic field is expressed as F = BILsin∝ where;

B is the magnetic field (in Tesla)

I is the current (in amperes)

L is the length of the wire (in meters)

∝ is the angle that the conductor makes with the magnetic field.

Given parameters

L = 0.56 m

I = 2.6A

F = 0.24N

∝  = 90°

Required

magnitude of the magnetic field (B)

Substituting the given values into the formula given above we will have;

F = BILsin∝

0.24 = B * 2.6 * 0.56 sin90°

0.24 =  B * 2.6 * 0.56 (1)

0.24 = 1.456B

1.456B = 0.24

Dividing both sides by 1.456 will give;

1.456B/1.456 = 0.24/1.456

B ≈ 0.165Tesla

Hence the magnitude of the magnetic field is approximately 0.165Tesla

A toroidal solenoid has 590 turns, cross-sectional area 6.20 cm^2 , and mean radius 5.00 cm .Part A. Calcualte the coil's self-inductance.Part B. If the current decreases uniformly from 5.00 A to 2.00 A in 3.00 ms, calculate the self-induced emf in the coil.Part C. The current is directed from terminal a of the coil to terminal b. Is the direction of the induced emf froma to b or from b to a?

Answers

Complete Question

A toroidal solenoid has 590 turns, cross-sectional area 6.20 cm^2 , and mean radius 5.00 cm .

Part A. Calculate  the coil's self-inductance.

Part B. If the current decreases uniformly from 5.00 A to 2.00 A in 3.00 ms, calculate the self-induced emf in the coil.

Part C. The current is directed from terminal a of the coil to terminal b. Is the direction of the induced emf from a to b or from b to a?

Answer:

Part A  

       [tex]L = 0.000863 \ H[/tex]

Part B  

       [tex]\epsilon = 0.863 \ V[/tex]

Part C

    From terminal a to terminal b

Explanation:

From the question we are told that

      The  number of turns is  [tex]N = 590 \ turns[/tex]

      The cross-sectional area is  [tex]A = 6.20 cm^2 = 6.20 *10^{-4} \ m[/tex]

      The  radius is [tex]r = 5.0 \ cm = 0.05 \ m[/tex]

       

Generally the coils self -inductance is mathematically represented as

              [tex]L = \frac{ \mu_o N^2 A }{2 \pi * r }[/tex]

Where [tex]\mu_o[/tex] is the permeability of  free space with value [tex]\mu_o = 4\pi * 10^{-7} N/A^2[/tex]

substituting values

             [tex]L = \frac{ 4\pi * 10^{-7} * 590^2 6.20 *10^{-4} }{2 \pi * 0.05 }[/tex]

             [tex]L = \frac{ 2 * 10^{-7} * 590^2 6.20 *10^{-4} }{ 0.05 }[/tex]

             [tex]L = 0.000863 \ H[/tex]

Considering the Part B

      Initial current is [tex]I_1 = 5.00 \ A[/tex]

      Current at time t is [tex]I_t = 3.0 \ A[/tex]

       The  time taken is  [tex]\Delta t = 3.00 ms = 0.003 \ s[/tex]

The self-induced emf is mathematically evaluated as

          [tex]\epsilon = L * \frac{\Delta I}{ \Delta t }[/tex]          

=>         [tex]\epsilon = L * \frac{ I_1 - I_t }{ \Delta t }[/tex]

substituting values

             [tex]\epsilon = 0.000863 * \frac{ 5- 2 }{ 0.003 }[/tex]  

             [tex]\epsilon = 0.863 \ V[/tex]

The direction of the induced emf is  from a to b because according to Lenz's law the induced emf moves in the same direction as the current

This question involves the concepts of the self-inductance, induced emf, and Lenz's Law

A. The coil's self-inductance is "0.863 mH".

B. The self-induced emf in the coil is "0.58 volts".

C. The direction of the induced emf is "from b to a".

A.

The self-inductance of the coil is given by the following formula:

[tex]L=\frac{\mu_oN^2A}{2\pi r}[/tex]

where,

L = self-inductance = ?

[tex]\mu_o[/tex] = permeability of free space = 4π x 10⁻⁷ N/A²

N = No. of turns = 590

A = Cross-sectional area = 6.2 cm² = 6.2 x 10⁻⁴ m²

r = radius = 5 cm = 0.05 m

Therefore,

[tex]L=\frac{(4\pi\ x\ 10^{-7}\ N/A^2)(590)^2(6.2\ x\ 10^{-4}\ m^2)}{2\pi(0.05\ m)}[/tex]

L = 0.863 x 10⁻³ H = 0.863 mH

B.

The self-induced emf is given by the following formula:

[tex]E=L\frac{\Delta I}{\Delta t}\\\\[/tex]

where,

E = self-induced emf = ?

ΔI = change in current = 2 A

Δt = change in time = 3 ms = 0.003 s

Therefore,

[tex]E=(0.000863\ H)\frac{2\ A}{0.003\ s}[/tex]

E = 0.58 volts

C.

According to Lenz's Law, the direction of the induced emf always opposes the change in flux that causes it. Hence, the direction of the induced emf will be from b to a.

Learn more about Lenz's Law here:

https://brainly.com/question/12876458?referrer=searchResults

A long solenoid consists of 1700 turns and has a length of 0.75 m.The current in the wire is 0.48 A. What is the magnitude of the magnetic field inside the solenoid

Answers

Answer:

1.37 ×10^-3 T

Explanation:

From;

B= μnI

μ = 4π x 10-7 N/A2

n= number of turns /length of wire = 1700/0.75 = 2266.67

I= 0.48 A

Hence;

B= 4π x 10^-7 × 2266.67 ×0.48

B= 1.37 ×10^-3 T

A typical ten-pound car wheel has a moment of inertia of about 0.35kg *m2. The wheel rotates about the axle at a constant angular speed making 70.0 full revolutions in a time interval of 4.00 seconds. What is the rotational kinetic energy K of the rotating wheel? Express answer in Joules

Answers

Answer:

The  rotational kinetic energy is  [tex]K = 2116.3 \ J[/tex]

Explanation:

From the question we are told that

    The moment of inertia  is  [tex]I = 0.35 \ kg \cdot m^2[/tex]

    The number of revolution is N  =  70 revolution

     The  time taken is  t  =  4.0  s

   

Generally the angular velocity is mathematically represented as

      [tex]w = \frac{2 \pi N }{t }[/tex]

substituting values

      [tex]w = \frac{2* 3.142 * 70 }{4 }[/tex]

       [tex]w = 109.97 \ rad/s[/tex]

     

The rotational kinetic energy K i mathematically represented as

       [tex]K = \frac{1}{ 2} * I * w^2[/tex]

substituting values

       [tex]K = \frac{1}{ 2} * 0.35 * (109.97)^2[/tex]

       [tex]K = 2116.3 \ J[/tex]

Given three resistors of different values, how many possible resistance values could be obtained by using one or more of the resistors?

Answers

Answer:

8 possible combinations

Assuming R 1, R 2 and R 3 be three different Resistance

1- all three in series

2-all three in parallel

3- R 1 and R 2 in series and parallel with R 3

4-R 1 and R 3 in series and parallel with R 2

5-R 2 and R 3 in series and parallel with R 1

6- R 1 and R 2

in parallel and series with R 3

7-R 1 and R 3 in parallel and series with R 2

8-R 2 and R 3 in V with R 1

A particle with charge q and momentum p, initially moving along the x-axis, enters a region where a uniform magnetic field* B=(B0)(k) extends over a width x=L. The particle is deflected a distance d in the +y direction as it traverses the field. Determine the magnitude of the momentum (p).

Answers

Answer:

Magnitude of momentum = q × B0 × [d^2 + 2L^2] / 2d.

Explanation:

So, from the question, we are given that the charge = q, the momentum = p.

=> From the question We are also given that, "initially, there is movement along the x-axis which then enters a region where a uniform magnetic field* B = (B0)(k) which then extends over a width x = L, the distance = d in the +y direction as it traverses the field."

Momentum,P = mass × Velocity, v -----(1).

We know that for a free particle the magnetic field is equal to the centrepetal force. Thus, we have the magnetic field = mass,.m × (velocity,v)^2 / radius, r.

Radius,r = P × v / B0 -----------------------------(2).

Centrepetal force = q × B0 × v. ----------(3).

(If X = L and distance = d)Therefore, the radius after solving binomially, radius = (d^2 + 2 L^2) / 2d.

Equating Equation (2) and (3) gives;

P = B0 × q × r.

Hence, the Magnitude of momentum = q × B0 × [d^2 + 2L^2] / 2d.

At what rate must Uranium 235 undergo fission by neutron bombardment to generate energy at a rate of 100 W (1 W

Answers

Complete Question

At what rate must Uranium 235 undergo fission by neutron bombardment to generate energy at a rate of 100 W (1 W = 1 J/s)? Assume each fission reaction releases 200 MeV of energy.

Answer

a. Approximately [tex]5*10^{10}[/tex] fissions per second.

b. Approximately [tex]6*10^{12 }[/tex]fissions per second.

c. Approximately [tex]4*10^{11}[/tex] fissions per second.

d. Approximately [tex]3*10^{12}[/tex] fissions per second.

e. Approximately[tex]3*10^{14}[/tex] fissions per second.

Answer:

The correct option is  d

Explanation:

From the question we are told that

       The energy released by each fission reaction [tex]E = 200 \ MeV = 200 *10^{6} * 1.60 *10^{-19} =3.2*10^{-11} \ J /fission[/tex]

Thus to generated  [tex]100 \ J/s[/tex] i.e  (100 W  ) the rate of fission is  

              [tex]k = \frac{100}{3.2 *10^{-11} }[/tex]

              [tex]k =3*10^{12} fission\ per \ second[/tex]

A jumbo jet has a mass of 100,000 kg. The thrust of each of its four engines is 50,000 N. What is the jet's acceleration in meters per second squared right before taking off? Neglect air resistance and friction.

Answers

Answer:

The acceleration is   [tex]a =2\ m/s^2[/tex]

Explanation:

From the question we are told that

       The  mass of the jumbo jet is  [tex]m_j = 100000\ kg[/tex]

        The thrust is  [tex]F_k = 50000 \ N[/tex]

Generally given that the jet has four engines the total thrust is  

        [tex]F_t = 4 * F_k[/tex]

substituting values

       [tex]F_t = 4 * 50000[/tex]

      [tex]F_t = 200000 \ N[/tex]

Generally the acceleration of the is mathematically represented as

         [tex]a = \frac{F_t}{m}[/tex]

substituting values

       [tex]a =2 \frac{N}{kg}[/tex]

Now  

        [tex]N = kg \cdot m/s^2[/tex]

Hence

         [tex]a =2 \frac{kg * \cdot m/s^2}{kg}[/tex]

        [tex]a =2\ m/s^2[/tex]

Which statement belongs to Dalton’s atomic theory? Atoms have a massive, positively charged center. Atoms cannot be created or destroyed. Atoms can be broken down into smaller pieces. Electrons are located in energy levels outside of the nucleus.

Answers

Answer:

the correct statement is

* atoms cannot be created or destroyed

Explanation:

The Datlon atomic model was proposed in 1808 and represents atoms as the smallest indivisible particle of matter, they were the building blocks of matter and are represented by solid spheres.

Based on the previous descriptive, the correct statement is

* atoms cannot be created or destroyed

Answer:

the Answer is b hope it help

Explanation:

Other Questions
An online company wants to establish ratings for the products they provide. To do so, they ask visitors to their website to evaluate the products and leave a "thumbs up" or a "thumbs down." What type of sample is this? Explain why. List three methods of assigning probabilities. (Select all that apply.)a. histogram.b. intuition .c. guessing .d. equally likely outcomes .e. relative frequency.f. cumulative frequency. How many equations are thereof: 70 divided by h equals 10?What are those equations? Help plisss What sign of dissatisfaction with the government administration did the American people show in 1930?A. Democrats were elected overwhelmingly to CongressB. President Hoover was kicked out of officeC. Mass violent protests outside the White HouseD. Federal taxes stopped being paid nationwide You missed your payment due date and now have $300 on your card that has a 24% APR. You are able to pay $100 in one month and then every month after that. How many months will it take you to pay this credit card off? Design specifications reflecting customer requirements for a product are known as:________ a) control limits b) capability indices c) natural variability d) tolerances Which observation led Mendel to the idea that traits were controlled by more than a single factor? Crossing two purple-flowered pea plants always resulted in a purple-flowered pea plant. Crossing two white-flowered pea plants always resulted in a white-flowered pea plant. A trait that was not seen in the first generation may later reappear in the second generation. A trait that was not seen in the first generation was completely gone and never reappeared. Write a skit depicting an unacceptable employee behavior. Your skit must include at least three characters. List any props used by the characters in your skit. The skit must be at least five minutes long. Example skit themes might be an employee using a personal cell phone at work, an employee not calling in when absent, an employee arriving late for work, an employee not following employer policy on dealing with customers or on expenses, or others. When finished with the skit, write a short paragraph explaining why the topic of your skit is an unacceptable employee behavior. Download the Skit Script Writing Worksheet and use it to complete your assignment. When you're satisfied with your assignment, upload it in the box below. There are (43)2 40 strawberries on a farm. What is the total number of strawberries on the farm? The right of the state to enact and enforce laws for the order, safety, health, morals, and general welfare of the public is known as:_____. What are some traditional stories An SN2 reaction is a type of _____________ in which the nucleophile attacks the electrophile. B(n)=2^n A binary code word of length n is a string of 0's and 1's with n digits. For example, 1001 is a binary code word of length 4. The number of binary code words, B(n), of length n, is shown above. If the length is increased from n to n+1, how many more binary code words will there be? The answer is 2^n, but I don't get how they got that answer. I would think 2^n+1 minus 2^n would be 2. Please help me! Thank you! 5 of 17Questions Question 5 Safiya needs to find a number that can be multiplied by 183 to result in a rational product. Which values could she use? Select all that apply. Steelcase Inc. is one of the largest manufacturers of office furniture in the United States. In Grand Rapids, Michigan, it produces filing cabinets in two departments: Fabrication and Assembly. Assume the following information for the Assembly Department:Steel per filing cabinet ............................................. 55 poundsDirect labor per filing cabinet ...................................... 20 minutesSupervisor salaries ................................................ $180,000 per monthDepreciation ...................................................... $28,000 per monthDirect labor rate................................................... $21 per hourSteel cost ......................................................... $0.40 per poundRequired:Prepare a flexible budget for 12,000, 15,000, and 18,000 filing cabinets for the month of August 2014. In a recent year, a sample of grade 8 Washington State public school students taking a mathematics assessment test had a mean score of 281 with a standard deviation of 34.4. Possible test scores could range from 0 to 500. Assume that the scores are normally distributed. Question 9 (2.5 points) If 2000 students are randomly selected, how many would you expect to have a score between 250 and 305? Think of an ethical question that might arise in your own life. What are two possible answers to the question? Which answer do you think is better? Assume that you have recently purchased 250 shares in an investment company. Upon examining the balance sheet, you note that the firm is reporting $320 million in assets, $60 million in liabilities, and 25 million shares outstanding. What is the net asset value (NAV) of these shares Which of the following goes through the largest volumetric change? Question 4 options: A) Water when it's heated from 1oC to 99oC B) Water when it freezes into ice C) Ice when it melts into water D) Water when it boils into steam the/to/company/dubai/goods/exports