Answer: her rotational kinetic energy increases
Which of these cannot be a resistor in a series or parallel circuit?
A)switch
B) battery
C) light bulb
D) all of these are resistors
Answer:
it is going to D. all of these are resistors
A Cannonball is shot at an angle of 35.0 degrees and is in flight for 11.0 seconds before hitting the ground at the same height from which it was shot.
A. What is the magnitude of the inital velocity?B. What was the maximum height reached by the cannonball?C. How far, horizontally, did it travel?
Answer:
Explanation:
According to Equations of Projectile motion :
[tex]Time\ of\ Flight = \frac{2vsin(x)}{g}[/tex]
vsin(x) = 11 * 9.8 / 2 = 53.9 m/sec
(A) v (Initial velocity) = 11 * 9.8 / 2 * sin(35) = 94.56 m/sec
[tex]Maximum Height = \frac{(vsinx)^{2} }{2g}[/tex]
(B) Maximum Height = 53.9 * 53.9 / 2 * 9.8 = 142.2 m
[tex]Horizontal Range = vcosx * t[/tex]
(C) Horizontal Range = 94.56 * 0.81 * 11 = 842.52 m
Water pressurized to 3.5 x 105 Pa is flowing at 5.0 m/s in a horizontal pipe which contracts to 1/2 its former radius. a. What are the pressure and velocity of the water after the contraction
Answer:
Explanation:
Using the Continuity equation
v X A = v' xA'
so if A is 1/2of A' then A velocity must be 2 times the A'
after-contraction v = 2 x 5.0m/s = 10m/s
Using the Bernoulli equation
p₁ + ½ρv₁² + ρgh₁ = p₂ + ½ρv₂² + ρgh₂
, the "h" terms cancel
3.5 x 10^ 5Pa + ½ x 1000kg/m³x (5.0m/s)² = p₂ + ½ x 1000kg/m³ x (10m/s)²
p₂ = 342500pa
In the lab, you shoot an electron towards the south. As it moves through a magnetic field, you observe the electron curving upward toward the roof of the lab. You deduce that the magnetic field must be pointing:_______.
a. to the west.
b. upward.
c. to the north.
d. to the east.
e. downward.
Answer:
a. to the west.
Explanation:
An electron in a magnetic field always experience a force that tends to change its direction of motion through the magnetic field. According to Lorentz left hand rule (which is the opposite of Lorentz right hand rule for a positive charge), the left hand is used to represent the motion of an electron in a magnetic field. Hold out the left hand with the fingers held out parallel to the palm, and the thumb held at right angle to the other fingers. If the thumb represents the motion of the electron though the field, and the other fingers represent the direction of the field, then the palm will push in the direction of the force on the particle.
In this case, if we point the thumb (which shows the direction we shot the electron) to the south (towards your body), with the palm (shows the direction of the force) facing up to the roof, then the fingers (the direction of the field) will point west.
A ball is thrown upward from a height of 432 feet above the ground, with an initial velocity of 96 feet per second. From physics it is known that the velocity at time t is v (t )equals 96 minus 32 t feet per second. a) Find s(t), the function giving the height of the ball at time t. b) How long will the ball take to reach the ground? c) How high will the ball go?
Answer;
A)S(t)=96t-16t² +432
B)it will take 9 seconds for the ball to reach the ground.
C)864feet
Explanation:
We were given an initial height of 432 feet.
And v(t)= 96-32t
A) we are to Find s(t), the function giving the height of the ball at time t
The position, or heigth, is the integrative of the velocity. So
S(t)= ∫(96-32)dt
S(t)=96t-16t² +K
S(t)=96t-16t² +432
In which the constant of integration K is the initial height, so K= 432
b) we need to know how long will the ball take to reach the ground
This is t when S(t)= 0
S(t)=96t-16t² +432
-16t² +96t +432=0
This is quadratic equation, if you solve using factorization method we have
t= -3 or t= 9
Therefore, , t is the instant of time and it must be a positive value.
So it will take 9 seconds for the ball to reach the ground.
C)V=s/t
Velocity= distance/ time
=96=s/9sec
S=96×9
=864feet
By applying the integrations,
(a) [tex]S = 96t-16t^2+432[/tex]
(b) Time will be "t = 9".
(c) Height will be "576"
Given:
Height,
423 feetInitial velocity,
96 feet/secAccording to the question,
(a)
Integrate v:
[tex]S = 96t-16t^2+C[/tex]Initial Condition,
→ [tex]S = 96t-16t^2+432[/tex]
(b)
Hits the ground when,
S = 0→ [tex]0=96t-16t^2+432[/tex]
→ [tex]t =9[/tex]
(c)
Maximum height when,
v = 0→ [tex]0 = 96-32 t[/tex]
→ [tex]t = 3[/tex]
Now,
→ [tex]S = 96\times 3-16\times 3^2+432[/tex]
[tex]= 576[/tex]
Thus the answer above is correct.
Learn more:
https://brainly.com/question/16105731
A fish is 80 cm below the surface of a pond. What is the apparent depth (in cm) when viewed from a position almost directly above the fish
Answer:
Apparent depth (Da) = 60.15 cm (Approx)
Explanation:
Given:
Distance from fish (D) = 80 cm
Find:
Apparent depth (Da)
Computation:
We know that,
Refractive index of water (n2) = 1.33
So,
Apparent depth (Da) = D(n1/n2)
Apparent depth (Da) = 80 (1/1.33)
Apparent depth (Da) = 60.15 cm (Approx)
The apparent depth of the fish is 60 cm.
To calculate the apparent depth of the fish, we use the formula below.
Formula:
R.F(water) = Real depth(D)/Apparent depth(D')R.F = D/D'.................... Equation 1Where:
R.F = Refractive index of waterMake D' The subject of the equation.
D' = D/R.F................... Equation 2From the question,
Given:
D = 80 cmR.F = 1.333Substitute these values into equation 2
D' = 80/1.33D' = 60.01D' = 60 cmHence, the apparent depth of the fish is 60 cm
Learn more about apparent depth here: https://brainly.com/question/24319677
Two 1.0 nF capacitors are connected in series to a 1.5 V battery. Calculate the total energy stored by the capacitors.
Answer:
1.125×10⁻⁹ J
Explanation:
Applying,
E = 1/2CV²................... Equation 1
Where E = Energy stored in the capacitor, C = capacitance of the capacitor, V = Voltage of the battery.
Given; C = 1.0 nF, = 1.0×10⁻⁹ F, V = 1.5 V
Substitute into equation 1
E = 1/2(1.0×10⁻⁹×1.5²)
E = 1.125×10⁻⁹ J
Hence the energy stored by the capacitor is 1.125×10⁻⁹ J
A double-convex thin lens is made of glass with an index of refraction of 1.52. The radii of curvature of the faces of the lens are 60 cm and 72 cm. What is the focal length of the lens
Answer:
63 cm
Explanation:
Mathematically;
The focal length of a double convex lens is given as;
1/f = (n-1)[1/R1 + 1/R2]
where n is the refractive index of the medium given as 1.52
R1 and R2 represents radius of curvature which are given as 60cm and 72cm respectively.
Plugging these values into the equation, we have:
1/f = (1.52-1)[1/60 + 1/72)
1/f = 0.0158
f = 1/0.0158
f = 63.29cm which is approximately 63cm
Which of the following explains why a “control” is important in a case-control study of a disease? The researchers need to control the bias that those who contracted the disease may create when they talk to others. The researchers need to compare those who contracted the disease to those who did not. The researchers need to compare those who contracted the disease to those who contracted previous diseases. The researchers need to control the disease so that it is not spread further.
The researchers need to compare those who contracted the disease to those who did not.
Question 18(Multiple Choice Worth 2 polnis)
When riding your skateboard you crash into a curb, the skateboard stops, and you continue moving forward. Which law of
motion is being described in this scenario?
O Law of Universal Gravitation
o Newton's Second Law of Motion
o Law of Conservation of Energy
o Newton's First Law of Motion
(a) Determine the capacitance of a Teflon-filled parallel-plate capacitor having a plate area of 1.80 cm2 and a plate separation of 0.010 0 mm.
pF
(b) Determine the maximum potential difference that can be applied to a Teflon-filled parallel-plate capacitor having a plate area of 1.80 cm2 and a plate separation of 0.010 0 mm.
kV
Explanation:
(a) Given that,
Area of a parallel plate capacitor, [tex]A=1.8\ cm^2=1.8\times 10^{-4}\ m^2[/tex]
The separation between the plates of a capacitor, [tex]d=0.01\ mm = 10^{-5}\ m[/tex]
The dielectric constant of, k = 2.1
When a dielectric constant is inserted between parallel plate capacitor, the capacitance is given by :
[tex]C=\dfrac{k\epsilon_o A}{d}[/tex]
Putting all the values we get :
[tex]C=\dfrac{2.1\times 8.85\times 10^{-12}\times 1.8\times 10^{-4}}{0.01\times 10^{-3}}\\\\C=3.345\times 10^{-10}\ F\\\\C=334.5\ pF[/tex]
(b) We know that the Teflon has dielectric strength of 60 MV/m, [tex]E=60\times 10^6\ V/m[/tex]
The voltage difference between the plates at this critical voltage is given by :
[tex]V=Ed\\\\V=60\times 10^6\times 0.01\times 10^{-3} \\\\V=600\ V[/tex]
or
V = 0.6 kV
We have that the Capacitance and potential difference is mathematically given as
[tex]Vmax=\frac{Q}{334.68pF}[/tex]C=334.68pF
Capacitance &potential differenceQuestion Parameters:
having a plate area of 1.80 cm2 and a plate separation of 0.010 0 mm
having a plate area of 1.80 cm2 and a plate separation of 0.010 0 mm.
a)
Generally the equation for the Capacitance is mathematically given as
[tex]C=\frac{ke_0A}{d}\\\\Therefore\\\\C=\frac{2.1*1.80e-4*8.85e12}{0.01e-3}\\\\[/tex]
C=334.68pF
b)
Generally the equation for the Capacitance is mathematically given as
[tex]Vmax=\frac{Q}{C}[/tex]
Where
Q is the charge on the plates, and hence not given
Therefore, maximum potential difference is
[tex]Vmax=\frac{Q}{334.68pF}[/tex]
For more information on potential difference visit
https://brainly.com/question/14883923
At what speed (in m/s) will a proton move in a circular path of the same radius as an electron that travels at 7.45 ✕ 106 m/s perpendicular to the Earth's magnetic field at an altitude where the field strength is 1.10 ✕ 10−5 T
Answer:
The speed of the proton is 4059.39 m/s
Explanation:
The centripetal force on the particle is given by;
[tex]F = \frac{mv^2}{r}[/tex]
The magnetic force on the particle is given by;
[tex]F = qvB[/tex]
The centripetal force on the particle must equal the magnetic force on the particle, for the particle to remain in the circular path.
[tex]\frac{mv^2}{r} = qvB\\\\r = \frac{mv^2}{qvB} \\\\r = \frac{mv}{qB}[/tex]
where;
r is the radius of the circular path moved by both electron and proton;
⇒For electron;
[tex]r = \frac{(9.1*10^{-31})(7.45*10^6)}{(1.602*10^{-19})(1.1*10^{-5})}\\\\r = 3.847 \ m[/tex]
⇒For proton
The speed of the proton is given by;
[tex]r = \frac{mv}{qB}\\\\mv = qBr\\\\v = \frac{qBr}{m} \\\\v = \frac{(1.602*10^{-19})(1.1*10^{-5})(3.847)}{1.67*10^{-27}} \\\\v = 4059.39 \ m/s[/tex]
Therefore, the speed of the proton is 4059.39 m/s
The molecules in Tyler are composed of carbon and other atoms that share one or more electrons between two atoms, forming what is known as a(n) _____ bond.
Answer:
covalent
Explanation:
covalent bonds share electrons
Specific heat is a measurement of the amount of heat energy input required for one gram of a substance to increase its temperature by one degree Celsius. Solid lithium has a specific heat of 3.5 J/g·°C. This means that one gram of lithium requires 3.5 J of heat to increase 1°C. Plot the temperature of 1g of lithium after 3.5, 7, and 10.5 J of thermal energy are added.
Answer:
ΔT = 1ºC , 2ºCand 3ºC
Explanation:
In this exercise they indicate the specific heat of lithium
let's calculate the temperature increase as a function of the heat introduced
Q = m [tex]c_{e}[/tex] ΔT
ΔT = Q / m c_{e}
calculate
for Q = 3.5 J
ΔT = 3.5 / (1 3.5)
ΔT = 1ºC
For Q = 7.0 J
ΔT = 7 / (1 3.5)
ΔT = 2ºC
for Q = 10.5 J
ΔD = 10.5 / (1 3.5)
ΔT = 3ºC
we see that this is a straight line, see attached
A small helium-neon laser emits red visible light with a power of 5.40 mW in a beam of diameter 2.30 mm.
Required:
a. What is the amplitude of the electric field of the light? Express your answer with the appropriate units.
b. What is the amplitude of the magnetic field of the light?
c. What is the average energy density associated with the electric field? Express your answer with the appropriate units.
d. What is the average energy density associated with the magnetic field? Express your answer with the appropriate units.
E) What is the total energy contained in a 1.00-m length of the beam? Express your answer with the appropriate units.
Answer:
A. 990v/m
B.330x10^-8T
C.2.19x10^-6J/m³
D.1.45x10^-11J
Explanation:
See attached file
A 2.0 m × 4.0 m flat carpet acquires a uniformly distributed charge of −10 μC after you and your friends walk across it several times. A 5.0 μg dust particle is suspended in midair just above the center of the carpet.
Required:
What is the charge on the dust particle?
Answer:
The charge on the dust particle is [tex]q_d = 6.94 *10^{-13} \ C[/tex]
Explanation:
From the question we are told that
The length is [tex]l = 2.0 \ m[/tex]
The width is [tex]w = 4.0 \ m[/tex]
The charge is [tex]q = -10\mu C= -10*10^{-6} \ C[/tex]
The mass suspended in mid-air is [tex]m_a = 5.0 \mu g = 5.0 *10^{-6} \ g = 5.0 *10^{-9} \ kg[/tex]
Generally the electric field on the carpet is mathematically represented as
[tex]E = \frac{q}{ 2 * A * \epsilon _o}[/tex]
Where [tex]\epsilon _o[/tex] is the permittivity of free space with value [tex]\epsilon_o = 8.85*10^{-12} \ \ m^{-3} \cdot kg^{-1}\cdot s^4 \cdot A^2[/tex]
substituting values
[tex]E = \frac{-10*10^{-6}}{ 2 * (2 * 4 ) * 8.85*10^{-12}}[/tex]
[tex]E = -70621.5 \ N/C[/tex]
Generally the electric force keeping the dust particle on the air equal to the force of gravity acting on the particles
[tex]F__{E}} = F__{G}}[/tex]
=> [tex]q_d * E = m * g[/tex]
=> [tex]q_d = \frac{m * g}{E}[/tex]
=> [tex]q_d = \frac{5.0 *10^{-9} * 9.8}{70621.5}[/tex]
=> [tex]q_d = 6.94 *10^{-13} \ C[/tex]
A circular conducting loop of radius 31.0 cm is located in a region of homogeneous magnetic field of magnitude 0.700 T pointing perpendicular to the plane of the loop. the loop is connected in series with a resistor of 265 ohms. The magnetic field is now increased at a constant rate by a factor of 2.30 in 29.0 s.
Calculate the magnitude of induced emf in the loop while the magnetic field is increasing.
With the magnetic field held constant a ts its new value of 1.61 T, calculate the magnitude of its induced voltage in the loop while it is pulled horizontally out of the magnetic field region during a time interval of 3.90s.
Answer:
(a) The magnitude of induced emf in the loop while the magnetic field is increasing is 9.5 mV
(b) The magnitude of the induced voltage at a constant magnetic field is 124.7 mV
Explanation:
Given;
radius of the circular loop, r = 31.0 cm = 0.31 m
initial magnetic field, B₁ = 0.7 T
final magnetic field, B₂ = 2.3B₁ = 2.3 X 0.7 T = 1.61 T
duration of change in the field, t = 29
(a) The magnitude of induced emf in the loop while the magnetic field is increasing.
[tex]E = A*\frac{\delta B}{\delta t} \\\\[/tex]
[tex]E = A*\frac{B_2 -B_1}{\delta t}[/tex]
Where;
A is the area of the circular loop
A = πr²
A = π(0.31)² = 0.302 m²
[tex]E = A*\frac{B_2 -B_1}{\delta t} \\\\E = 0.302*\frac{1.61-0.7}{29} \\\\E = 0.0095 \ V\\\\E = 9.5 \ mV[/tex]
(b) the magnitude of the induced voltage at a constant magnetic field
E = A x B/t
E = (0.302 x 1.61) / 3.9
E = 0.1247 V
E = 124.7 mV
Therefore, the magnitude of the induced voltage at a constant magnetic field is 124.7 mV
If a disk rolls on a rough surface without slipping, the acceleration of the center of gravity (G) will _ and the friction force will b
Answer:
Will be equal to alpha x r; less than UsN
An electric device delivers a current of 5.0 A to a circuit. How many electrons flow through this circuit in 5 s?
Answer:
1.6×10²⁰
Explanation:
An ampere is a Coulomb per second.
1 A = 1 C / s
The amount of charge after 5 seconds is:
5.0 A × 5 s = 25 C
The number of electrons is:
25 C × (1 electron / 1.6×10⁻¹⁹ C) = 1.6×10²⁰ electrons
The power lines are at a high potential relative to the ground, so there is an electric field between the power lines and the ground. To maximize the potential difference between one end of the fluorescent tube and the other, how should the tube be held?a. The tube should be held horizontally, parallel to the ground b. The potential difference between the ends of the tube does not depend on the tube's orientation. c. The tube should be held vertically perpendicular to the ground
Answer:
b) True. potencial diferencie does not depend on orientation
Explanation:
In this exercise we are asked to show which statements are true.
The expression the potential with respect to earth or the electric field with respect to earth refers to the potential or electric charge of the planet that is assumed to be very large and does not change in value during work.
It does not refer to the height of the system.
We can now review the claims
a) False. Potential not to be refers to height
b) True. Does not depend on orientation
c) False The potential does not refer to the altitude but to the Earth's charge
Convert 76.2 kilometers to meters?
Answer
76200meters
Explanation:
we know that 1km=1000meters
to convert km into meters we we divide km by meters
=76.2/1000
=76200meters
Intelligent beings in a distant galaxy send a signal to earth in the form of an electromagnetic wave. The frequency of the signal observed on earth is 2.2% greater than the frequency emitted by the source in the distant galaxy. What is the speed vrel of the galaxy relative to the earth
Answer:
Vrel= 0.75c
Explanation:
See attached file
A load of 1 kW takes a current of 5 A from a 230 V supply. Calculate the power factor.
Answer:
Power factor = 0.87 (Approx)
Explanation:
Given:
Load = 1 Kw = 1000 watt
Current (I) = 5 A
Supply (V) = 230 V
Find:
Power factor.
Computation:
Power factor = watts / (V)(I)
Power factor = 1,000 / (230)(5)
Power factor = 1,000 / (1,150)
Power factor = 0.8695
Power factor = 0.87 (Approx)
If the x-position of a particle is measured with an uncertainty of 1.00×10-10 m, then what is the uncertainty of the momentum in this same direction? (Useful constant: h-bar = 1.05×10-34 Js.)
Answer:
The uncertainty in momentum is 5.25x 10^25Jsm
Explanation:
We know that
h bar = h/2π
So
1.05x 10^34=h/2pπ
h=1.05x 10^ 34(2π)=6.597x 10^-34Js
dp=(6.597x10^-34/4pπ)/(1x10^-10)
=5.25x10^-25 Jsm
hi guys!!! i have no more points, can someone nice guess all of these for me? :)
1.What happens to the ocean water before the precipitation part of the water cycle
2.During which stage of the water cycle does water from the ocean form clouds?
3.what is a runoff??
4.Which statement about oceans is incorrect? A.Evaporation occurs when water is warmed by the sun. B.Most evaporation and precipitation occur over the ocean. C.97 percent of Earth's water is fresh water from the ocean. D.Water leaves the ocean by the process of evaporation
5.How does most ocean water return to the ocean in the water cycle
tysm to u who answers :)
1. The ocean water collects back in the ocean.
2. Condensation is the process by which water vapor in the air is changed into liquid water. Condensation is crucial to the water cycle because it is responsible for the formation of clouds.
3. an excessive amount of water flowing from downslope along earths surface
4. A.Evaporation occurs when water is warmed by the sun.
5. The water returns into the ocean by the water cycle . It evaporates , then it condensates , then it participates ( Rains ) and then goes back into the ocean.
Hope this answer correct ✌️
The advantage of a hydraulic lever is A : it transforms a small force acting over a large distance into a large force acting over a small distance. B : it transforms a small force acting over a small distance into a large force acting over a large distance. C : it allows you to exert a larger force with less work. D : it transforms a large force acting over a large distance into a small force acting over a small distance. E : it transforms a large force acting over a small distance into a small force acting over a large distance.
Answer:
A) it transforms a small force acting over a large distance into a large force acting over a small distance.
Explanation:
The hydraulic lever works based on Pascal's law of transmission of pressure through a fluid. In the hydraulic lever, the pressure transmitted is the same.
Pressure transmitted P = F/A
where F is the force applied
and A is the area over which the force is applied.
This pressure can be manipulated on the input end as a small force applied over a small area, and then be transmitted to the output end as a large force over a large area.
F/A = f/a
where the left side of the equation is for the output, and the right side is for the input.
The volume of the displaced fluid will be the same on both ends of the hydraulic lever. Since we know that
volume V = (area A) x (distance d)
this means that the the piston on the input smaller area of the hydraulic lever will travel a greater distance, while the piston on the larger output area of the lever will travel a small distance.
From all these, we can see that the advantage of a hydraulic lever is that it transforms a small force acting over a large distance into a large force acting over a small distance.
light of wavelength 550 nm is incident on a diffraction grating that is 1 cm wide and has 1000 slits. What is the dispersion of the m = 2 line?
Answer:
The dispersion is [tex]D = 2.01220 *10^{5} \ rad/m[/tex]
Explanation:
From the question we are told that
The wavelength of the light is [tex]\lambda = 550 \ = 550 *10^{-9} \ n[/tex]
The width of the grating is[tex]k = 1\ cm = 0.01 \ m[/tex]
The number of slit is N = 1000 slits
The order of the maxima is m = 2
Generally the spacing between the slit is mathematically represented as
[tex]d = \frac{k}{N}[/tex]
substituting values
[tex]d = \frac{ 0.01}{1000}[/tex]
[tex]d = 1.0 *10^{-5} \ m[/tex]
Generally the condition for constructive interference is
[tex]d\ sin(\theta ) = m * \lambda[/tex]
substituting values
[tex]1.0 *10^{-5} sin (\theta) = 2 * 550 *10^{-9}[/tex]
[tex]\theta = sin^{-1} [\frac{ 2 * 550 *10^{-9}}{ 1.0 *10^{-5}} ][/tex]
[tex]\theta = 6.315^o[/tex]
Generally the dispersion is mathematically represented as
[tex]D = \frac{ m }{d cos(\theta )}[/tex]
substituting values
[tex]D = \frac{ 2 }{ 1.0 *10^{-5} cos(6.315 )}[/tex]
[tex]D = 2.01220 *10^{5} \ rad/m[/tex]
Without actually calculating any logarithms, determine which of the following intervals the sound intensity level of a sound with intensity 3.66×10^−4W/m^2 falls within?
a. 30 and 40
b. 40 and 50
c. 50 and 60
d. 60 and 70
e. 70 and 80
f. 80 and 90
g. 90 and 100
Answer:
f. 80 and 90
Explanation:
1 x 10⁻¹² W/m² sound intensity falls within 0 sound level
1 x 10⁻¹¹ W/m² sound intensity falls within 10 sound level
1 x 10⁻¹⁰ W/m² sound intensity falls within 20 sound level
1 x 10⁻⁹ W/m² sound intensity falls within 30 sound level
1 x 10⁻⁸ W/m² sound intensity falls within 40 sound level
1 x 10⁻⁷ W/m² sound intensity falls within 50 sound level
1 x 10⁻⁶ W/m² sound intensity falls within 60 sound level
1 x 10⁻⁵ W/m² sound intensity falls within 70 sound level
1 x 10⁻⁴ W/m² sound intensity falls within 80 sound level
1 x 10⁻³ W/m² sound intensity falls within 90 sound level
Given sound intensity (3.66 x 10⁻⁴ W/m²) falls with 1 x 10⁻⁴ W/m² of intensity which is within 80 and 90 sound level.
f. 80 and 90
An electric train operates on 800 V. What is its power consumption when the current flowing through the train's motor is 2,130 A?
Answer:
1704 kWExplanation:
To solve for the power consumed by the trains motor we have to employ the formula for power which is
Power= current * voltage
Given that
voltage V= 800 V
current I= 2130 A
Substituting in the formula for power we have
Power= 2130*800= 1704000 watt
Power = 1704 kW
This is the amount of energy consumed, transferred or converted per unit of time
Hence the power consumed by the trains motor is 1704 kW
If you wish to observe features that are around the size of atoms, say 5.5 × 10^-10 m, with electromagnetic radiation, the radiation must have a wavelength of about the size of the atom itself.
Required:
a. What is its frequency?
b. What type of electromagnetic radiation might this be?
Answer:
a) 5.5×10^17 Hz
b) visible light
Explanation:
Since the wavelength of the electromagnetic radiation must be about the size of the about itself, this implies that;
λ= 5.5 × 10^-10 m
Since;
c= λ f and c= 3×10^8 ms-1
f= c/λ
f= 3×10^8/5.5 × 10^-10
f= 5.5×10^17 Hz
The electromagnetic wave is visible light
