A concrete slab shown in Figure 5 is being lifted by using three cables connected to the slab at points A, B and C. The slab is in the xy plane. The vertical force required to lift this slab is 60 kN (F 60 kN). Find the tensions in cables DA, DB and DC (show all your workings that you do to find these)

Explanation:

Given that,

Initial speed of the rock, u = 30 m/s

The acceleration due to gravity at the surface of the moon is 1.62 m/s².

We need to find the time when the rock is ascending at a height of 180 m.

The rock is projected from the surface of the moon. The equation of motion in this case is given by :

[tex]h=ut-\dfrac{1}{2}gt^2\\\\180=30t-\dfrac{1}{2}\times 1.62t^2[/tex]

It is a quadratic equation, after solving whose solution is given by:

t = 7.53 s

or

t = 8 seconds

(e)If it is decending, v = -20 m/s

Now t' is the time of descending. So,

[tex]v=-u+gt\\\\t=\dfrac{v+u}{g}\\\\t=\dfrac{20+30}{1.62}\\\\t=30.86\ s[/tex]

Let h' is the height of the rock at this time. So,

[tex]h'=ut-\dfrac{1}{2}gt^2\\\\h'=30\times 30.86-\dfrac{1}{2}\times 1.62\times 30.86^2\\\\h'=154.40\ m[/tex]

or

h' = 155 m

Answer:

A. 30.38°

B 5.04N

Explanation:

Using

F= ILBsin theta

2 .55N= 8.4Ax 0.5mx 1.2T x sintheta

Theta = 30.38°

B. If theta is 90°

Then

F= 8.4Ax 0.5mx 1.2x sin 90°

F= 5.04N

Answer:

Option 2 (observing, measuring, testing, and explaining their ideas) is the correct choice.

Explanation:

The other three choices have no relation to a particular task. So the option given here is just the right one.

Answer:

physical feature of a wave is related to the depth of the wave base is The circular orbital motion

B. The wave base is the depth, and the still water level is the horizontal level

Answer:

60 km/hour.

Explanation:

We'll begin by calculating the total distance traveled by the car. This is illustrated below:

Total distance traveled = sum of distance between PQRST

Total distance = 10 + 5 + 10 + 5

Total distance = 30 km

Next, we shall convert 30 mins to hour. This can obtained as follow:

Recall:

60 mins = 1 hour

Therefore,

30 mins = 30/60 = 0.5 hour.

Finally, we shall determine the average speed of the car as follow:

Distance = 30 km

Time = 0.5 hour

Speed =?

Speed = distance /time

Speed = 30/0.5

Speed = 60 km/hour

Therefore, the speed of the car is 60 km/hour.

Answer:

Speed of the electron is 2.46 x 10^8 m/s

Explanation:

momentum of the electron before relativistic effect = [tex]M_{0} V[/tex]

where [tex]M_{0}[/tex] is the rest mass of the electron

V is the velocity of the electron.

under relativistic effect, the mass increases.

under relativistic effect, the new mass M will be

M = [tex]M_{0}/ \sqrt{1 - \beta ^{2} }[/tex]

where

[tex]\beta = V/c[/tex]

c  is the speed of light = 3 x 10^8 m/s

V is the speed with which the electron travels.

The new momentum will therefore be

==> [tex]M_{0}V/ \sqrt{1 - \beta ^{2} }[/tex]

It is stated that the relativistic momentum is 1.75 times the non-relativistic momentum. Equating, we have

1.75[tex]M_{0} V[/tex] = [tex]M_{0}V/ \sqrt{1 - \beta ^{2} }[/tex]

the equation reduces to

1.75 = [tex]1/ \sqrt{1 - \beta ^{2} }[/tex]

square both sides of the equation, we have

3.0625 = 1/[tex](1 - \beta ^{2} )[/tex]

3.0625 - 3.0625[tex]\beta ^{2}[/tex] = 1

2.0625 = 3.0625[tex]\beta ^{2}[/tex]

[tex]\beta ^{2}[/tex] = 0.67

β = 0.819

substitute for  [tex]\beta = V/c[/tex]

V/c = 0.819

V = c x 0.819

V = 3 x 10^8 x 0.819 = 2.46 x 10^8 m/s

Answer:

The reason for the increase or decrease of the moon is due to the angular perception of the moon.

Explanation:

Also called lunar illusion, this phenomenon is due to the position in which the moon is, it can be at the zenith or on the horizon, both distances are different from each other with respect to the position of the person.

The zenith is the highest part of the sky and the horizon the lowest.

When there are landmarks such as trees, buildings or mountains on the horizon, the illusion of closeness is given and the illusion of distance is misinterpreted.

But when looking up at the sky as there is no reference point there will be a failure in the perception of size.

Answer:

T = 3.14 hours

Explanation:

We need to find the orbital period (in hours) of an observation satellite in a circular orbit 1,787 km above Mars.

We know that the radius of Mars is 3,389.5 km.

So, r = 1,787 + 3,389.5 = 5176.5 km

Using Kepler's law,

[tex]T^2=\dfrac{4\pi ^2}{GM}r^3[/tex]

M is mass of Mars, [tex]M=6.39\times 10^{23}\ kg[/tex]

So,

[tex]T^2=\dfrac{4\pi ^2}{6.67\times 10^{-11}\times 6.39\times 10^{23}}\times (5176.5 \times 10^3)^3\\\\T=\sqrt{\dfrac{4\pi^{2}}{6.67\times10^{-11}\times6.39\times10^{23}}\times(5176.5\times10^{3})^{3}}\\\\T=11334.98\ s[/tex]

or

T = 3.14 hours

So, the orbital period is 3.14 hours

Answer: R=24.2Ω

Explanation: Power is rate of work being done in an electric circuit. It relates to voltage, current and resistance through the following formulas:

P=V.i

P=R.i²

[tex]P=\frac{V^{2}}{R}[/tex]

The resistance of the system is:

[tex]P=\frac{V^{2}}{R}[/tex]

[tex]R=\frac{V^{2}}{P}[/tex]

[tex]R=\frac{110^{2}}{500}[/tex]

R = 24.2Ω

For the device, resistance is 24.2Ω.

Answer:

8 seconds

Explanation:

Answer:

Explanation:

Going up

Time taken to reach maximum height= usin∅/g

=3 secs

Maximum height= H+[(usin∅)²/2g]

=80+[(60sin30)²/20]

=125 meters

Coming Down

Maximum height= ½gt²

125= ½(10)(t²)

t=5 secs

Answer: f ≈ 8.5Hz

Explanation: The phenomenon known as Doppler Shift is characterized as a change in frequency when one observer is stationary and the source emitting the frequency is moving or when both observer and source are moving.

For a source moving and a stationary observer, to determine the frequency:

[tex]f_{0} = f_{s}.\frac{c}{c-v_{s}}[/tex]

where:

[tex]f_{0}[/tex] is frequency of observer;

[tex]f_{s}[/tex] is frequency of source;

c is the constant speed of sound c = 340m/s;

[tex]v_{s}[/tex] is velocity of source;

Rearraging for frequency of source:

[tex]f_{0} = f_{s}.\frac{c}{c-v_{s}}[/tex]

[tex]f_{s} = f_{0}.\frac{c-v_{s}}{c}[/tex]

Replacing and calculating:

[tex]f_{s} = 9.(\frac{340-20}{340})[/tex]

[tex]f_{s} = 9.(0.9412)[/tex]

[tex]f_{s} =[/tex] 8.5

Frequency the horns emit is 8.5Hz.

Answer:

E = 2.48 eV

Explanation:

The energy of a photon is given by the following formula:

E = hυ

where,

E = Energy of Photon = ?

h = Plank's Constant = 6.626 x 10⁻³⁴ J.s

υ = frequency of photon = c/λ

Therefore,

E = hc/λ

where,

c = speed of light = 3 x 10⁸ m/s

λ = wavelength of light = 500 nm = 5 x 10⁻⁷ m

Therefore,

E = (6.626 x 10⁻³⁴ J.s)(3 x 10⁸ m/s)/(5 x 10⁻⁷ m)

E = (3.97 x 10⁻¹⁹ J)(1 eV/1.6 x 10⁻¹⁹ J)

E = 2.48 eV

A photon of visible light that has a wavelength of 500 nm, has an energy of 2.48 eV.

We can calculate the energy (E) of a photon with a wavelength (λ) of 500 nm using the Planck's-Einstein relation.

[tex]E = \frac{h \times c}{\lambda } = \frac{(6.63 \times 10^{-34}J.s ) \times (3.00 \times 10^{8}m/s )}{500 \times 10^{-9}m } = 3.98 \times 10^{-19} J[/tex]

where,

We can convert 3.98 × 10⁻¹⁹ J to eV using the conversion factor 1 J = 6.24 × 10¹⁸ eV.

[tex]3.98 \times 10^{-19} J \times \frac{6.24 \times 10^{18} eV }{1J} = 2.48 eV[/tex]

A photon of visible light that has a wavelength of 500 nm, has an energy of 2.48 eV.

Learn more: https://brainly.com/question/2058557

Answer

The effect is that it Decreases the field current IF and increases slope K1

Answer:

a barometer is used to measure atmospheric pressure, and a manometer is used to measure gauge pressure.

Explanation:

A barometer measures air pressure at any locality with sea level as the reference.

However, a manometer is used to measure all pressures especially gauge pressures. Thus, if the aim is to measure the pressure at any point below a fluid surface, a barometer is used to determine the air pressure. The manometer may now be used to determine the gauge pressure

The algebraic sum of these two values gives the absolute pressure.

Answer:

221 lines per millimetre

Explanation:

We know that for a diffraction grating, dsinθ =mλ where d = spacing between grating, θ = angle to maximum, m = order of maximum and λ = wavelength of light.

Since the grating is 42.0 cm from the screen and its first order maximum (m = 1) is at 6.09 cm from the center of the pattern,

tanθ = 6.09 cm/42.0 cm = 0.145

From trig ratios, cot²θ + 1 = cosec²θ

cosecθ = √((1/tanθ)² + 1) = √((1/0.145)² + 1) = √48.562 = 6.969

sinθ = 1/cosecθ = 1/6.969 = 0.1435

Also, sinθ = mλ/d at the first-order maximum, m = 1. So

sinθ = (1)λ/d = λ/d

Equating both expressions we have  

0.1435 = λ/d

d = λ/0.1435

Now, λ = 650 nm = 650 × 10⁻⁹ m

d = 650 × 10⁻⁹ m/0.1435

d = 4529.62 × 10⁻⁹ m per line

d = 4.52962 × 10⁻⁶ m per line

d = 0.00452962 × 10⁻³ m per line

d = 0.00452962 mm per line

Since d = width of grating/number of lines of grating

Then number of lines per millimetre = 1/grating spacing

= 1/0.00452962

= 220.77 lines per millimetre

≅ 221 lines per millimetre since we can only have a whole number of lines.

a. I've attached a plot of the surface. Each face is parameterized by

• [tex]\mathbf s_1(x,y)=x\,\mathbf i+y\,\mathbf j[/tex] with [tex]0\le x\le2[/tex] and [tex]0\le y\le6-x[/tex];

• [tex]\mathbf s_2(u,v)=u\cos v\,\mathbf i+u\sin v\,\mathbf k[/tex] with [tex]0\le u\le2[/tex] and [tex]0\le v\le\frac\pi2[/tex];

• [tex]\mathbf s_3(y,z)=y\,\mathbf j+z\,\mathbf k[/tex] with [tex]0\le y\le 6[/tex] and [tex]0\le z\le2[/tex];

• [tex]\mathbf s_4(u,v)=u\cos v\,\mathbf i+(6-u\cos v)\,\mathbf j+u\sin v\,\mathbf k[/tex] with [tex]0\le u\le2[/tex] and [tex]0\le v\le\frac\pi2[/tex]; and

• [tex]\mathbf s_5(u,y)=2\cos u\,\mathbf i+y\,\mathbf j+2\sin u\,\mathbf k[/tex] with [tex]0\le u\le\frac\pi2[/tex] and [tex]0\le y\le6-2\cos u[/tex].

b. Assuming you want outward flux, first compute the outward-facing normal vectors for each face.

[tex]\mathbf n_1=\dfrac{\partial\mathbf s_1}{\partial y}\times\dfrac{\partial\mathbf s_1}{\partial x}=-\mathbf k[/tex]

[tex]\mathbf n_2=\dfrac{\partial\mathbf s_2}{\partial u}\times\dfrac{\partial\mathbf s_2}{\partial v}=-u\,\mathbf j[/tex]

[tex]\mathbf n_3=\dfrac{\partial\mathbf s_3}{\partial z}\times\dfrac{\partial\mathbf s_3}{\partial y}=-\mathbf i[/tex]

[tex]\mathbf n_4=\dfrac{\partial\mathbf s_4}{\partial v}\times\dfrac{\partial\mathbf s_4}{\partial u}=u\,\mathbf i+u\,\mathbf j[/tex]

[tex]\mathbf n_5=\dfrac{\partial\mathbf s_5}{\partial y}\times\dfrac{\partial\mathbf s_5}{\partial u}=2\cos u\,\mathbf i+2\sin u\,\mathbf k[/tex]

Then integrate the dot product of f with each normal vector over the corresponding face.

[tex]\displaystyle\iint_{S_1}\mathbf f(x,y,z)\cdot\mathrm d\mathbf S=\int_0^2\int_0^{6-x}f(x,y,0)\cdot\mathbf n_1\,\mathrm dy\,\mathrm dx[/tex]

[tex]=\displaystyle\int_0^2\int_0^{6-x}0\,\mathrm dy\,\mathrm dx=0[/tex]

[tex]\displaystyle\iint_{S_2}\mathbf f(x,y,z)\cdot\mathrm d\mathbf S=\int_0^2\int_0^{\frac\pi2}\mathbf f(u\cos v,0,u\sin v)\cdot\mathbf n_2\,\mathrm dv\,\mathrm du[/tex]

[tex]\displaystyle=\int_0^2\int_0^{\frac\pi2}-u^2(2\sin v+\cos v)\,\mathrm dv\,\mathrm du=-8[/tex]

[tex]\displaystyle\iint_{S_3}\mathbf f(x,y,z)\cdot\mathrm d\mathbf S=\int_0^2\int_0^6\mathbf f(0,y,z)\cdot\mathbf n_3\,\mathrm dy\,\mathrm dz[/tex]

[tex]=\displaystyle\int_0^2\int_0^60\,\mathrm dy\,\mathrm dz=0[/tex]

[tex]\displaystyle\iint_{S_4}\mathbf f(x,y,z)\cdot\mathrm d\mathbf S=\int_0^2\int_0^{\frac\pi2}\mathbf f(u\cos v,6-u\cos v,u\sin v)\cdot\mathbf n_4\,\mathrm dv\,\mathrm du[/tex]

[tex]=\displaystyle\int_0^2\int_0^{\frac\pi2}-u^2(2\sin v+\cos v)\,\mathrm dv\,\mathrm du=\frac{40}3+6\pi[/tex]

[tex]\displaystyle\iint_{S_5}\mathbf f(x,y,z)\cdot\mathrm d\mathbf S=\int_0^{\frac\pi2}\int_0^{6-2\cos u}\mathbf f(2\cos u,y,2\sin u)\cdot\mathbf n_5\,\mathrm dy\,\mathrm du[/tex]

[tex]=\displaystyle\int_0^{\frac\pi2}\int_0^{6-2\cos u}12\,\mathrm dy\,\mathrm du=36\pi-24[/tex]

c. You can get the total flux by summing all the fluxes found in part b; you end up with 42π - 56/3.

Alternatively, since S is closed, we can find the total flux by applying the divergence theorem.

[tex]\displaystyle\iint_S\mathbf f(x,y,z)\cdot\mathrm d\mathbf S=\iiint_R\mathrm{div}\mathbf f(x,y,z)\,\mathrm dV[/tex]

where R is the interior of S. We have

[tex]\mathrm{div}\mathbf f(x,y,z)=\dfrac{\partial(3x)}{\partial x}+\dfrac{\partial(x+y+2z)}{\partial y}+\dfrac{\partial(3z)}{\partial z}=7[/tex]

The integral is easily computed in cylindrical coordinates:

[tex]\begin{cases}x(r,t)=r\cos t\\y(r,t)=6-r\cos t\\z(r,t)=r\sin t\end{cases},0\le r\le 2,0\le t\le\dfrac\pi2[/tex]

[tex]\displaystyle\int_0^2\int_0^{\frac\pi2}\int_0^{6-r\cos t}7r\,\mathrm dy\,\mathrm dt\,\mathrm dr=42\pi-\frac{56}3[/tex]

as expected.

Explanation:

Consider a loop of wire, which has an area of [tex]A=14 \mathrm{cm}^{2}[/tex] and [tex]N=250[/tex] turns, it is initially placed perpendicularly in the earth magnetic field. Then it is rotated from this position to a position where its plane is parallel to the field as shown in the following figure in [tex]\Delta t=0.030[/tex] s. Given that the earth's magnetic field at the position of the loop is [tex]B=5.0 \times 10^{-5} \mathrm{T}[/tex], the flux through the loop before it is rotated is,

[tex]\Phi_{B, i} &=B A \cos \left(\phi_{i}\right)=B A \cos \left(0^{\circ}\right[/tex]

[tex]=\left(5.0 \times 10^{-5} \mathrm{T}\right)\left(14 \times 10^{-4} \mathrm{m}^{2}\right)(1)[/tex]

[tex]=7.0 \times 10^{-8} \mathrm{Wb}[/tex]

[tex]\quad\left[\Phi_{B, i}=7.0 \times 10^{-8} \mathrm{Wb}\right[/tex]

after it is rotated, the angle between the area and the magnetic field is [tex]\phi=90^{\circ}[/tex] thus,

[tex]\Phi_{B, f}=B A \cos \left(\phi_{f}\right)=B A \cos \left(90^{\circ}\right)=0[/tex]

[tex]\qquad \Phi_{B, f}=0[/tex]

(b) The average magnitude of the emf induced in the coil equals the change in the flux divided by the time of this change, and multiplied by the number of turns, that is,

[tex]{\left|\mathcal{E}_{\mathrm{av}}\right|=N\left|\frac{\Phi_{B, f}-\Phi_{B, i}}{\Delta t}\right|}{=} & \frac{1.40 \times 10^{-5} \mathrm{Wb}}{0.030 \mathrm{s}}[/tex]

[tex]& 3.6 \times 10^{-4} \mathrm{V}=0.36 \mathrm{mV}[/tex]

[tex]\mathbb{E}=0.36 \mathrm{mV}[/tex]

(a) The initial and final flux through the coil is 1.75 × 10⁻⁵ Wb and 0 Wb

(b) The induced EMF in the coil is 0.583 mV

Given that the coil has N = 250 turns

and an area of A = 14cm² = 1.4×10⁻³m².

It is rotated for a time period of Δt = 0.030s such that it is parallel with the earth's magnetic field that is B = 5×10⁻⁵T

(a) The flux passing through the coil is given by:

Ф = NBAcosθ

where θ is the angle between area vector and the magnetic field

The area vector is perpendicular to the plane of the coil.

So, initially, θ = 0°, as area vector and earth's magnetic field both are perpendicular to the plane of the coil

So the initial flux is:

Φ = NABcos0° = NAB

Ф = 250×1.4×10⁻³×5×10⁻⁵ Wb

Ф = 1.75 × 10⁻⁵ Wb

Finally, θ = 90°, and since cos90°, the final flux through the coil is 0

(b) The EMF induced is given by:

E = -ΔФ/Δt

E = -(0 - 1.75 × 10⁻⁵)/0.030

E = 0.583 × 10⁻³ V

E = 0.583 mV

Learn more about magnetic flux:

https://brainly.com/question/15359941?referrer=searchResults

Complete Question

At what rate must Uranium 235 undergo fission by neutron bombardment to generate energy at a rate of 100 W (1 W = 1 J/s)? Assume each fission reaction releases 200 MeV of energy.

Answer

a. Approximately [tex]5*10^{10}[/tex] fissions per second.

b. Approximately [tex]6*10^{12 }[/tex]fissions per second.

c. Approximately [tex]4*10^{11}[/tex] fissions per second.

d. Approximately [tex]3*10^{12}[/tex] fissions per second.

e. Approximately[tex]3*10^{14}[/tex] fissions per second.

Answer:

The correct option is  d

Explanation:

From the question we are told that

       The energy released by each fission reaction [tex]E = 200 \ MeV = 200 *10^{6} * 1.60 *10^{-19} =3.2*10^{-11} \ J /fission[/tex]

Thus to generated  [tex]100 \ J/s[/tex] i.e  (100 W  ) the rate of fission is  

              [tex]k = \frac{100}{3.2 *10^{-11} }[/tex]

              [tex]k =3*10^{12} fission\ per \ second[/tex]

Answer:

The time taken is  [tex]t = 2.739 *10^{8} \ s[/tex]

Explanation:

From the question we are told that

    The speed of the spacecraft is [tex]v = 0.99c[/tex]

    where c is the speed of light with value [tex]c = 3.0*10^{8} \ m/s[/tex]

    =>   [tex]v = 0.99 * 3.0 *10^{8 } = 2.97*10^{8}\ m/s[/tex]

    The distance of Sirius is [tex]d = 8.6 \ light-years = 8.6 * 9.461*10^{15}= 8.135*10^{16} \ m[/tex]

Generally the time taken is mathematically represented as

       [tex]t = \frac{d}{v}[/tex]

substituting values

      [tex]t = \frac{8.136 *10^{16}}{2.97 *10^{8}}[/tex]

      [tex]t = 2.739 *10^{8} \ s[/tex]

CHECK COMPLETE QUESTION BELOW

you stood on a planet having a mass four times that of earth mass and a radius two times of earth radius , you would weigh?

A) four times more than you do on Earth.

B) two times less than you do on Earth.

C) the same as you do on Earth

D) two times more than you do on Earth

Answer:

OPTION C is correct

The same as you do on Earth

Explanation :

According to law of gravitation :

F=GMm/R^2......(a)

F= mg.....(b)

M= mass of earth

m = mass of the person

R = radius of the earth

From law of motion

Put equation b into equation a

mg=GMm/R^2

g=GMm/R^2

g=GM/R^2

We know from question a planet having a mass four times that of earth mass and a radius two times of earth radius if we substitute we have

m= 4M

r=(2R)^2=4R^2

g= G4M/4R^2

Then, 4in the denominator will cancel out the numerator we have

g= GM/R^2

Therefore, g remain the same

Answer: 156.02 metre.

Explanation:

Give that a certain car traveling 33.0mph skids to a stop in 39m from the point where the brakes were applied.

Let us use third equation of motion,

V^2 = U^2 + 2as

Since the car is decelerating, V = 0

And acceleration a will be negative.

U = 33 mph

S = 39 m

Substitute both into the formula

0 = 33^2 - 2 × a × 39

0 = 1089 - 78a

78a = 1089

a = 1089 / 78

a = 13.96 m/h^2

If we assume that the car decelerate at the same rate.

the distance the car will stop had it been going 66.0mph will be achieved by using the same formula

V^2 = U^2 + 2as

0 = 66^2 - 2 × 13.96 × S

4356 = 27.92S

S = 4356 / 27.92

S = 156.02 m

Therefore, the car would stop at

156.02 m

Answer:

 Good Diet: ! gallon of water a day, Fruits, Vegetables, White meats(Chicken), Don't eat past 3 PM.

Bad Diet: Pizza, Red meat, Baked goods, Eating at late hours.

Explanation: I know the difference because, When you drink water first thing in the morning it gets your metabolism running. Than means you can digest foods better, you want to feed your body good foods but you should not eat until you feel stuffed. You should eat until you are no longer starving. Than you should drink a cup of water in between meals. I know you should not eat past 3 pm because your body needs time to digest foods because you should never go to sleep with a full stomach. I know the difference between good food and bad food because when you eat healthy food and a balanced diet, your body will have more energy and you wont feel tired afterwards. Eating bad foods and food with artificial sugars will clump up in your kidneys, and your body will have small bursts of energy but you will feel lazy afterwards...Your body is supposed to stay energized from a healthy meal in order to give you the energy your body needs to exercise. If you feel droopy all the time and you don't want to do anything, than you are unhealthy.

Answer:

A vegetarian diet is an example of a good fad diet if you do it correctly. It can help you get lots of veggies and good nutrients from them while still following the non-meat diet you want. This can be effective and good for weight loss becasue you are still eating and getting all the good nutrients and calories from less fatty foods. 

Vegan diet (some can be successful but many people fail and do not do good that is why I choose this) The problem with this fad diet is that it can cause nutritional deficiencies and lead to a host of additional health problems, including negatively impacting hormonal health and metabolism. Many people also struggle to find healthy vegan food and end up eating bad and fatty foods instead. 

Explanation:

Got a 100

Answer:

. The loop is pushed to the right, away from the magnetic field

Explanation

This decrease in magnetic strength causes an opposing force that pushes the loop away from the field

Answer:

4.635 *10^12 Neutrinos

Explanation:

Here in this question, we are to determine the number of neutrinos in billions produced, given the power generated by the proton-proton cycle.

We proceed as follows;

In proton-proton cycle generates 26.7 MeV of energy and in this cycle two neutrinos are produced.

From the question, we are given that

Power P = 9.9 watts = 9.9 J/s

Watts is same as J/s

The number of proton-proton cycles required to generate E energy is N = E / E '

Where E ' = Energy generated in proton-proton cycle which is given as 26.7 Mev in the question

Converting Mev to J, we have

= 26.7 x1.6 x10 -13 J

To get the number N which is the number of proton-proton cycle required, we have;

N = 9.9 /(26.7 x1.6 x10^-13) = 2.32 * 10^12

Since we have two proton cycles( proton-proton), it automatically means 2 neutrinos will be produced.

Therefore number of neutrions produced = 2 x Number of proton-proton cycles = 2 * 2.32 * 10^12 = 4.635 * 10^12 neutrinos

Answer:

The electron will get at about 0.388 cm (about 4 mm) from the negative plate before stopping.

Explanation:

Recall that the Electric field is constant inside the parallel plates, and therefore the acceleration the electron feels is constant everywhere inside the parallel plates, so we can examine its motion using kinematics of a constantly accelerated particle. This constant acceleration is (based on Newton's 2nd Law:

[tex]F=m\,a\\q\,E=m\,a\\a=\frac{q\,E}{m}[/tex]

and since the electric field E in between parallel plates separated a distance d and under a potential difference [tex]\Delta V[/tex], is given by:

[tex]E=\frac{\Delta\,V}{d}[/tex]

then :

[tex]a=\frac{q\,\Delta V}{m\,d}[/tex]

We want to find when the particle reaches velocity zero via kinematics:

[tex]v=v_0-a\,t\\0=v_0-a\,t\\t=v_0/a[/tex]

We replace this time (t) in the kinematic equation for the particle displacement:

[tex]\Delta y=v_0\,(t)-\frac{1}{2} a\,t^2\\\Delta y=v_0\,(\frac{v_0}{a} )-\frac{a}{2} (\frac{v_0}{a} )^2\\\Delta y=\frac{1}{2} \frac{v_0^2}{a}[/tex]

Replacing the values with the information given, converting the distance d into meters (0.01 m), using [tex]\Delta V=100\,V[/tex], and the electron's kinetic energy:

[tex]\frac{1}{2} \,m\,v_0^2= (11.2)\,\, 1.6\,\,10^{-19}\,\,J[/tex]

we get:

[tex]\Delta\,y= \frac{1}{2} v_0^2\,\frac{m (0.01)}{q\,(100)} =11.2 (1.6\,\,10^{-19})\,\frac{0.01}{(1.6\,\,10^{-19})\,(100)}=\frac{11.2}{10000} \,meters=0.00112\,\,meters[/tex]Therefore, since the electron was initially at 0.5 cm (0.005 m) from the negative plate, the closest it gets to this plate is:

0.005 - 0.00112 m = 0.00388 m [or 0.388 cm]

Complete question is;

The place you get your hair cut has two nearly parallel mirrors 6.50 m apart. As you sit in the chair, your head is 3.00 m from the nearer mirror. Looking toward this mirror, you first see your face and then, farther away, the back of your head. (The mirrors need to be slightly nonparallel for you to be able to see the back of your head, but you can treat them as parallel in this problem.) How far away does the back of your head appear to be?

Answer:

13 m

Explanation:

We are given;

Distance between two nearly parallel mirrors; d = 6.5 m

Distance between the face and the nearer mirror; x = 3 m

Thus, the distance between the back-head and the mirror = 6.5 - 3 = 3.5m

Now, From the given values above and using the law of reflection, we can find the distance of the first reflection of the back of the head of the person in the rear mirror.

Thus;

Distance of the first reflection of the back of the head in the rear mirror from the object head is;

y' = 2y

y' = 2 × 3.5

y' = 7

The total distance of this image from the front mirror would be calculated as;

z = y' + x

z = 7 + 3

z = 10

Finally, the second reflection of this image will be 10 meters inside in the front mirror.

Thus, the total distance of the image of the back of the head in the front mirror from the person will be:

T.D = x + z

T.D = 3 + 10

T.D = 13m

Answer:

b. The current in the loop always flows in a counterclockwise direction.

Explanation:

When a magnet falls through a loop of wire, it induces an induced current on the loop of wire. This induced current is due to the motion of the magnet through the loop, which cause a change in the flux linkage of the magnet. According to Lenz law, the induced current acts in such a way as to repel the force or action that produces it. For this magnet, the only opposition possible is to stop its fall by inducing a like pole on the wire loop to repel its motion down. An induced current that flows counterclockwise in the wire loop has a polarity that is equivalent to a north pole on a magnet, and this will try to repel the motion of the magnet through the coil. Also, when the magnet goes pass the wire loop, this induced north pole will try to attract the south end of the magnet, all in a bid to stop its motion downwards.

The current in the loop always flows in a counterclockwise direction. Hence, option (b) is correct.

The given problem is based on the concept and fundamentals of magnetic bars. When a magnet falls through a loop of wire, it induces an induced current on the loop of wire. There is some magnitude of current induced in the wire.

Thus, we can say that the current in the loop always flows in a counterclockwise direction. Hence, option (b) is correct.

Learn more about the magnetic field here:

https://brainly.com/question/14848188

Answer:

The time difference is 2.97 sec.

Explanation:

Given that,

Tension = 29 N

Mass per unit length [tex]\mu_{1}=19\ kg/m[/tex]

Mass per unit length [tex]\mu_{2}=45\ kg/m[/tex]

Length of first section = 2.5 m

Length of second section = 2.8 m

We need to total distance of first pulse

Using formula for distance

[tex]d=2.5+2.5[/tex]

[tex]d_{1}=5.0\ m[/tex]

We need to total distance of second pulse

Using formula for distance

[tex]d=2.8+2.8[/tex]

[tex]d_{2}=5.6\ m[/tex]

We need to calculate the speed of pulse in the first string

Using formula of speed

[tex]v_{1}=\sqrt{\dfrac{T}{\mu_{1}}}[/tex]

Put the value into the formula

[tex]v_{1}=\sqrt{\dfrac{29}{19}}[/tex]

[tex]v_{1}=1.24\ m/s[/tex]

We need to calculate the speed of pulse in the second string

Using formula of speed

[tex]v_{2}=\sqrt{\dfrac{T}}{\mu_{2}}}[/tex]

Put the value into the formula

[tex]v_{2}=\sqrt{\dfrac{29}{45}}[/tex]

[tex]v_{2}=0.80\ m/s[/tex]

We need to calculate the time for first pulse

Using formula of time

[tex]t_{1}=\dfrac{d_{1}}{v_{1}}[/tex]

Put the value into the formula

[tex]t_{1}=\dfrac{5.0}{1.24}[/tex]

[tex]t_{1}=4.03\ sec[/tex]

We need to calculate the time for second pulse

Using formula of time

[tex]t_{2}=\dfrac{d_{1}}{v_{1}}[/tex]

Put the value into the formula

[tex]t_{2}=\dfrac{5.6}{0.80}[/tex]

[tex]t_{2}=7\ sec[/tex]

We need to calculate the time difference

Using formula of time difference

[tex]\Delta t=t_{2}-t_{1}[/tex]

Put the value into the formula

[tex]\Delta t=7-4.03[/tex]

[tex]\Delta t=2.97\ sec[/tex]

Hence, The time difference is 2.97 sec.

Answer:

0.6 m/s

Explanation:

2Hz = 2^-1 = 2 /s

30cm = .3m

Velocity is in the units m/s, so multiplying wavelength in meters by the frequency will give you the velocity.

(.3m)*(2 /s) = 0.6 m/s