A condition that lifts a parcel of air to form cumulus clouds is
Answer
a. differential heating.
b. mountain barriers.
c. a cold front.
d. All of the above.

Answers

Answer 1

A condition that lifts a parcel of air to form cumulus clouds is  differential heating.

Thus, Differential heating of the land and the water. Water changes temperature more slowly because it has a high specific heat, like the ocean. Land, particularly sandy beaches, has a low specific heat, therefore it warms up faster than water with the same amount of heat.

Our beach towels are blown away by this land-and-water combination, but it is also to blame for more extreme weather like monsoons and thunderstorms and heat.

The typical afternoon thunderstorm might be produced by sea breezes. For instance, the Florida peninsula is bordered by the ocean on both sides. Cool air from the Gulf of Mexico blows inland on the western side as a sea breeze. A sea wind from the Atlantic Ocean causes the same thing to occur on the eastern side and differential heating.

Thus, A condition that lifts a parcel of air to form cumulus clouds is  differential heating.

Learn more about Heat, refer to the link:

https://brainly.com/question/30603212

#SPJ4


Related Questions

A 2000 Hz sound wave passes through a wall with two narrow openings 30 cm apart. If sound travels on average 334 m/s, find the following. (a) What is the angle of the first order maximum? ° (b) Find the slit separation when you replace the sound wave with a 2.25 cm microwave, and the angle of the first order maximum remains unchanged. m (c) If the slit separation is 1.00 µm, what frequency of light gives the same first order maximum angle? Hz

Answers

We have f = v/λ = 3 × 10⁸ / (1 × 10⁻⁶) = 3 × 10¹⁴ Hz (c)The frequency of light that gives the same first order maximum angle is 3 × 10¹⁴ Hz.

Given,Speed of sound, v = 334 m/sFrequency of sound wave, f = 2000 HzDistance between the two narrow openings, d = 30 cm = 0.3 Let us calculate the angle of the first order maximum angle of the sound wave. The formula used to find the angle of the first order maximum is given by sinθ = λ/d Where λ is the wavelength of the wave.We know that the velocity of sound wave, v = fλ⇒ λ = v/f = 334/2000 = 0.167 m

Using the above values in the formula, we have sinθ = λ/d⇒ θ = sin⁻¹(λ/d) = sin⁻¹(0.167/0.3) = 31.87° (a)The angle of the first order maximum is 31.87°.Now, we need to find the slit separation when we replace the sound wave with a 2.25 cm microwave, and the angle of the first order maximum remains unchanged.The formula used to find the slit separation is given by d = λ/ sinθLet λ1 be the wavelength of the microwave after replacing the sound wave.

We know that the angle of the first order maximum remains unchanged. Therefore,d/sinθ = d1/sinθ1⇒ d1 = d(sinθ1/sinθ)Let λ1 = 2.25 cm = 0.0225 m.Using the above values, we have d = λ/ sinθ⇒ d1 = d(sinθ1/sinθ) = (0.167/ sin31.87°) (sin31.87°) / (0.0225) = 4.67 m (b)The slit separation is 4.67 m.Now, we need to calculate the frequency of light that gives the same first order maximum angle. The formula used to calculate the frequency of light is given by f = v/λWe know that the wavelength of light = 1.00 µm = 1 × 10⁻⁶ m.

Using the above values, we have f = v/λ = 3 × 10⁸ / (1 × 10⁻⁶) = 3 × 10¹⁴ Hz (c)The frequency of light that gives the same first order maximum angle is 3 × 10¹⁴ Hz.

To learn more about frequency visit;

https://brainly.com/question/31992754

#SPJ11

what outcomes are in the event e, that the number of batteries examined is an even number?

Answers

The set of outcomes that is included in the event E, that the number of batteries examined is an even number, are as follows: {0, 2, 4, 6, 8, 10}.An event refers to a subset of the entire sample space of a random experiment that constitutes the collection of all possible outcomes. In this case, n(E) = 6 and n(S) = 11. Therefore, P(E) = 6 / 11

The event E indicates that the number of batteries examined is an even number. Therefore, only even numbers that are less than or equal to ten and greater than or equal to zero are a part of the event E, which includes 0, 2, 4, 6, 8, and 10. The sample space of this random experiment is the set of all possible outcomes.

If we assume that a total of 10 batteries are tested, the sample space is {0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10}.

So, the event E is a proper subset of the sample space, and the probability of E can be computed as:

P(E) = n(E) / n(S)

where n(E) is the number of outcomes in E, and n(S) is the number of outcomes in the sample space.

In this case, n(E) = 6 and n(S) = 11.

to know more about probability visit:

https://brainly.com/question/32117953

#SPJ11

determine the time it takes to achieve an angular velocity of ω = 198 rad/s . when t = 0, θ = 1 rad .

Answers

To determine the time it takes to achieve an angular velocity of ω = 198 rad/s, given that at t = 0, θ = 1 rad, we can use the equation of angular motion.

The equation that relates angular displacement, angular velocity, and time is θ = ω₀t + (1/2)αt², where θ is the angular displacement, ω₀ is the initial angular velocity, t is the time, α is the angular acceleration, and t² denotes t squared.

In this case, we are given that ω₀ = 0 since the initial angular velocity is not provided. Assuming there is no angular acceleration mentioned, we can simplify the equation to θ = (1/2)αt².

Rearranging the equation to solve for time, we have t = sqrt((2θ) / α).

Substituting the given values, θ = 1 rad and ω = 198 rad/s, we need additional information on the angular acceleration (α) to calculate the time it takes to achieve the given angular velocity.

To know more about  angular acceleration, click here:

https://brainly.com/question/30237820

#SPJ11

the force per meter between the two wires of a jumper cable being utilized to start a stalled van is 0.215 n/m.

Answers

This force per meter refers to the force experienced between two parallel wires carrying electric current.

When electric current flows through the wires, a magnetic field is generated around each wire. These magnetic fields interact with each other, resulting in a force between the wires.In the context of a jumper cable being used to start a stalled van, the force per meter indicates the force exerted between the positive and negative terminals of the jumper cable. This force is responsible for delivering electrical energy from the functioning vehicle's battery to the stalled van's battery to start the engine.

To know more about energy visit :

https://brainly.com/question/1932868

#SPJ11

(20%) (a) (4%) Explain the coherence of wave and state its importance for interference. (b) (4 %) How to improve the interference result if you use a white-light bulb as the light source in Young's double slit experiment? (c) (4%) Explain why the degree of coherence of a laser is better than a light bulb. (d) (4%) A thin film of ZnS (n=2.37) is used to coat a camera lens (ng-1.53) so that it is antireflecting at a wavelength of 550 nm under normal incidence. Find the minimum thickness of the thin film. (e) (4%) A thin film of MgF2 (n= 1.38) is used to coat a camera lens (ng-1.53) so that it is antireflecting at a wavelength of 580 nm under normal incidence. What wavelength is minimally reflected when the light is incident instead at 45⁰?

Answers

A wave's ability to produce stationary interference is known as coherence.

Thus, Coherence is explained through several different ideas. Although these phenomena are uncommon in reality, they provide a basic grasp of waves. It has developed into a crucial idea in quantum physics and wave.

Thus, The term "coherence" refers to the characteristics of the correlation between the physical parameters of a single wave, a group of waves, or a wave packet.

For example, two parallel slits that are illuminated by a single laser beam can be categorized as two coherent sources. The photons of coherent light are in perfect time with one another. The phase shift for the light beam happens simultaneously.

Thus, A wave's ability to produce stationary interference is known as coherence.

Learn more about Wave, refer to the link:

https://brainly.com/question/3639648

#SPJ4

Q3: Please show your complete solution and explanation. Thank
you!
3. One mole of an ideal gas is expanded isothermally to twice its initial volume a) calculate AS. b) What would be the value of AS if five moles of an ideal gas were doubled in volume isothermally?

Answers

One mole of an ideal gas is expanded isothermally to twice its initial volume a) ΔS is equal to  (8.314 J/K) ln(2). b)  The value of ΔS would be approximately 41.57 ln(2) J/K if five moles of an ideal gas were doubled in volume isothermally.

a) The change in entropy (ΔS) for the isothermal expansion of one mole of an ideal gas, we can use the equation:

ΔS = nR ln(Vf/Vi)

Where:

ΔS is the change in entropy,

n is the number of moles of gas (1 mole in this case),

R is the ideal gas constant (8.314 J/(mol·K)),

Vf is the final volume,

Vi is the initial volume.

Since the volume is expanded to twice its initial value, we have Vf = 2Vi.

Plugging these values into the equation, we get:

ΔS = (1 mole)(8.314 J/(mol·K)) ln(2Vi/Vi)

      = (8.314 J/K) ln(2)

b) If five moles of an ideal gas were doubled in volume isothermally, we can calculate the change in entropy (ΔS) using the same equation as above, but with n = 5:

ΔS = (5 moles)(8.314 J/(mol·K)) ln(2Vi/Vi)

      = (41.57 J/K) ln(2)

Therefore, the value of ΔS would be approximately 41.57 ln(2) J/K for five moles of an ideal gas when doubled in volume isothermally.

To learn more about isothermally refer here:

https://brainly.com/question/31828834#

#SPJ11

A 6.70-C charge of mass 4.10 x 10-12 kg is moving with a speed of 1.60 x 105 m/s in a 0.400-T uniform magnetic field. Y Part A - Determine the magnitude of the magnetic force on the charge if it is mo

Answers

The magnitude of the magnetic force on the charge is 4.97 x 10^-4 N. This calculation is based on the charge of 6.70 C, the velocity of 1.60 x 10^5 m/s, and the magnetic field of 0.400 T.

The magnetic force on a charged particle moving in a magnetic field can be calculated using the equation:

Force = Charge × Velocity × Magnetic Field

Given that the charge is 6.70 C, the velocity is 1.60 x 10^5 m/s, and the magnetic field is 0.400 T, we can calculate the magnitude of the magnetic force:

Force = (6.70 C) × (1.60 x 10^5 m/s) × (0.400 T)

= 4.97 x 10^-4 N

The magnetic force is perpendicular to both the velocity of the charge and the magnetic field direction, following the right-hand rule.

The magnitude of the magnetic force on the charge is 4.97 x 10^-4 N. This calculation is based on the charge of 6.70 C, the velocity of 1.60 x 10^5 m/s, and the magnetic field of 0.400 T. The force is determined using the equation that relates charge, velocity, and magnetic field strength. The magnetic force acts perpendicular to both the velocity of the charge and the direction of the magnetic field.

To know more about magnetic visit:

https://brainly.com/question/26257705

#SPJ11

The 300 gram billiard ball of 30 mm radius is struck by a cue stick that exerts an average force of 600 N horizontally over a 0.005 s interval. Immediately after being hit, the billiard ball rolls without slipping. Determine (a) the height h for the cue stick, and (b) the velocity of the ball after the impact.

Answers

If the 300 gram billiard ball of 30 mm radius is struck by a cue stick that exerts an average force of 600 N horizontally over a 0.005 s interval. Immediately after being hit, the billiard ball rolls without slipping. Then the height and velocity is 2.85 m & 7.5 m/s.

Given data:The mass of the billiard ball, m = 300 g = 0.3 kgRadius of the billiard ball, r = 30 mm = 0.03 mAverage force exerted by the cue stick, F = 600 N

Duration of the collision, t = 0.005 s Let's determine the height of the cue stick using the principle of conservation of energy.According to the principle of conservation of energy, the initial energy of the ball and the cue stick system should be equal to the final energy of the system.

Energy of the system before collision = Potential energy = mghEnergy of the system after the collision = Kinetic energy = (1/2)mv²

Now, equating both the energies, we get:mgh = (1/2)mv²... (1)

where h is the height of the cue stick and v is the velocity of the ball after the impact.Let's determine the velocity of the ball using the principle of impulse and momentum.

According to the principle of impulse and momentum, the impulse experienced by the ball is equal to the change in momentum of the ball.Impulse = F × t Change in momentum = mv - 0... (2

)Here, v is the velocity of the ball after the impact.Now, equating both the equations (1) and (2), we get:

mgh = (1/2)mv²⇒ v² = 2gh... (3)And,F × t = mv... (4)

Squaring both sides of equation (4), we get:(Ft)² = m²v² ⇒ v² = (Ft)²/m²... (5)Substituting the value of v² from equation (5) into equation (3), we get:

(Ft)²/m² = 2gh⇒ h = (Ft)²/2mg... (6)Substituting the given values into equation (6), we get:h = [(600 N × 0.005 s)²/(2 × 0.3 kg × 9.8 m/s²)] = 2.85 m

Therefore, the height of the cue stick is 2.85 m.Now, substituting the value of h into equation (3), we get:v² = 2gh⇒ v² = 2 × 9.8 m/s² × 2.85 m = 56.28 m²/s²⇒ v = √56.28 = 7.5 m/s Therefore, the velocity of the ball after the impact is 7.5 m/s.

To know more about velocity visit :

https://brainly.com/question/23855996

#SPJ11

what is the highest order dark fringe, , that is found in the diffraction pattern for light that has a wavelength of 629 nm and is incident on a single slit that is 1480 nm wide?

Answers

The highest order dark fringe, n is approximately equal to 2 for light that has a wavelength of 629 nm and is incident on a single slit that is 1480 nm wide.

The highest order dark fringe, n can be determined using the equation:

n λ = a sin θ

where,λ = 629 nma = 1480 nm

Given data:

wavelength (λ) = 629 nmsingle slit width (a) = 1480 nm

The highest order dark fringe, n can be determined using the equation:n λ = a sin θThe first dark fringe corresponds to n = 1, second dark fringe corresponds to n = 2, and so on.

For the highest order dark fringe, we need to find the largest value of n which gives a valid value of

sin θ.n λ = a sin θ ⇒ sin θ = (n λ) / a

For the highest order dark fringe, sin θ = 1 which gives:

n λ = a sin θ⇒ n λ = a⇒ n = a / λ

We have,a = 1480 nmλ = 629 nm

Substituting the values in the equation, we get:

n = a / λ= 1480 nm / 629 nm= 2.35 or 2 (approx)Therefore, the highest order dark fringe, n is approximately equal to 2

The highest order dark fringe, n is approximately equal to 2 for light that has a wavelength of 629 nm and is incident on a single slit that is 1480 nm wide.

To know more about dark fringe, visit:

https://brainly.com/question/31576174

#SPJ11

Consider a vertical pipe through which humid air flows. The pipe is kept at 5 oC, which is cooler than
the air and, importantly, below the 8 oC dew point of the air. As a result, water condenses on the
inner walls to maintain a thin layer of liquid water. Though the water layer would eventually get
thick enough that it would fall due to gravity, you can neglect that here.
a. Draw a picture of the physical system, select the coordinate system that best describes the
transfer process, and state at least five reasonable assumptions of the mass-transfer aspects of
the process.
b. What is the simplified form of the general differential equation for mass transfer in terms of the
flux of water vapor, NA?
c. What is the simplified differential form of Fick’s flux equation for water vapor?
d. What is the simplified form of the general differential equation for mass transfer in terms of the
molar concentration of water vapor, cA?

Answers

Assumptions: Assumptions are an important part of the process of modeling since they allow you to focus on the essential physics of the problem.

Correct option is a. Picture of the physical system:

Below are some of the assumptions made for the given system:It can be assumed that the flow of air is laminar.

The concentration of water vapor in the gas stream does not change as a result of the transfer process. The temperature at any location in the system is uniform and constant. The air does not undergo any significant change in pressure.

The only mass transfer process that occurs is evaporation and condensation.

b. The simplified form of the general differential equation for mass transfer in terms of the flux of water vapor, NA is,

c) The simplified differential form of Fick’s flux equation for water vapor is given by

d) The simplified form of the general differential equation for mass transfer in terms of the molar concentration of water vapor, cA is given by [tex]$\frac{\partial \frac{N_{A}}{\rho_{g}}}{\partial t}[/tex]

=[tex]\frac{\partial}{\partial z}\left[\frac{D_{AB}}{\rho_{g}}\frac{\partial c_{A}}{\partial z}\right]$[/tex]

To know more about laminar flow, visit:

https://brainly.com/question/23008935

#SPJ11

Suppose a pair of reading glasses found on the rack in a pharmacy has a power of 1.6 D. What is the focal length f, in centimeters? Numeric:

Answers

Given, Power of the reading glasses (P) = 1.6 D. Hence, the focal length of the pair of reading glasses found on the rack in a pharmacy is 62.5 cm.

To find, Focal length (f)Formula used,

Power of the reading glasses (P) = 1/f

where, Power (P) is measured in diopters, Focal length (f) is measured in meters.

Solving the above equation for focal length (f), we get:

focal length (f) = 1/P

focal length (f) = 1/1.6 D

focal length (f) = 0.625 meters

focal length (f) = 62.5 cm

to know more about focal length visit:

https://brainly.com/question/31755962

#SPJ11

What is the work done to slow a 1.8 x 10^5 kg train car from 60 m/s to 20 m/s? O-2.9 x 10^8 J O-1.3 x 10^3 J O 3.1 x 10^5 J O 6.1 x 10^4 J 2.9 x 10^6 J

Answers

The work done to slow the 1.8 x 10^5 kg train car from 60 m/s to 20 m/s is approximately -2.88 x 10^8 J = -2.9 x 10^8J

The work done to slow down a train car can be calculated using the formula:

Work = (1/2) * mass * (final velocity^2 - initial velocity^2)

Mass of the train car (m) = 1.8 x 10^5 kg

Initial velocity (u) = 60 m/s

Final velocity (v) = 20 m/s

Using the formula, we can calculate the work done:

Work = (1/2) * (1.8 x 10^5 kg) * [(20 m/s)^2 - (60 m/s)^2]

= (1/2) * (1.8 x 10^5 kg) * (400 m^2/s^2 - 3600 m^2/s^2)

= (1/2) * (1.8 x 10^5 kg) * (-3200 m^2/s^2)

= -2.88 x 10^8 J

Therefore, the work done to slow down the train car from 60 m/s to 20 m/s is approximately -2.88 x 10^8 J.

The correct option from the given choices is: O-2.9 x 10^8 J

When the train car slows down, the work done on the car is negative because the force applied is in the opposite direction to the displacement. The work done is equal to the change in kinetic energy of the car. In this case, the initial kinetic energy is higher than the final kinetic energy, hence the negative sign.

The work done to slow the 1.8 x 10^5 kg train car from 60 m/s to 20 m/s is approximately -2.88 x 10^8 J = -2.9 x 10^8J

To know more about work visit:

https://brainly.com/question/28356414

#SPJ11

Martha is viewing a distant mountain with a telescope that has a 120-cm-focal-length objective lens and an eyepiece with a 2.0 cm focal length. She sees a bird that's 42 m distant and wants to observe it. To do so, she has to refocus the telescope.
Part A
By how far must she move the eyepiece in order to focus on the bird?

Answers

To determine how far Martha must move the eyepiece in order to focus on the bird, we can use the lens formula.

To focus on the bird, Martha needs to adjust the eyepiece by a distance that brings the final image distance (v) to 50 m. The exact calculation for the movement of the eyepiece will depend on the specific values of u and the corresponding value of v.To determine the distance by which Martha must move the eyepiece in order to focus on the bird, we need to calculate the change in the position of the eyepiece.The change in the position of the eyepiece can be found by subtracting the initial position of the eyepiece from the final position.

To know more about eyepiece visit :

https://brainly.com/question/24547418

#SPJ11

How much work does the electric field do in moving a -6.4x10-6 charge from ground to a point whose potential is 92 V higher?

Answers

The work done by the electric field in moving a -6.4x10^-6 charge from ground to a point 92 V higher is -5.888x10^-4 J.

The work done by an electric field in moving a charge can be calculated using the formula:

Work = q * ΔV

Where:

Work is the work done (in joules)

q is the charge (in coulombs)

ΔV is the change in potential (in volts)

q = -6.4x10^-6 C

ΔV = 92 V

Substituting these values into the formula, we get:

Work = (-6.4x10^-6 C) * (92 V)

= -5.888x10^-4 J

The work done by the electric field in moving a -6.4x10^-6 charge from ground to a point whose potential is 92 V higher is -5.888x10^-4 J. The negative sign indicates that the electric field does work against the motion of the charge, as the charge is moving to a higher potential.

To know more about Work, visit

brainly.com/question/25573309

#SPJ11

The fundamental frequency of a pipe that is open at both ends is 594 Hz .
How long is this pipe?
If one end is now closed, find the wavelength of the newfundamental.
If one end is now closed, find the frequency of the newfundamental.

Answers

When one end is closed, the new wavelength is 1.154 m and the new fundamental frequency is 297 Hz.

The fundamental frequency of a pipe that is open at both ends is 594 Hz. In order to calculate the length of this pipe, we will use the formula v = fλ where v is the speed of sound, f is the frequency and λ is the wavelength.

The speed of sound in air is approximately 343 m/s.

We will therefore have: 594 = (343/λ)λ = (343/594)m = 0.577m or 57.7cm.

If one end of the pipe is now closed, it will act as a closed-end resonator which means that the wavelength will now be twice the length of the pipe.

Therefore, the new wavelength will be 2(0.577) = 1.154 m or 115.4 cm.

Using the formula v = fλ and substituting the new wavelength and speed of sound, we have 343 = f(1.154) which gives us the new fundamental frequency f as:

f = 297 Hz.

Thus, the length of the pipe that is open at both ends is 57.7 cm. When one end is closed, the new wavelength is 1.154 m and the new fundamental frequency is 297 Hz.

Learn more about fundamental frequency here:

https://brainly.com/question/31314205

#SPJ11

_______ increases when air faces greater resistance against an object with a larger surface area. (4 letters)

Answers

The term that increases when air faces greater resistance against an object with a larger surface area is drag.

The drag force is created when a solid object moves through a fluid (liquid or gas), such as air, and experiences resistance to its motion.Drag can be affected by various factors, including the object's shape and surface area. In general, objects with larger surface areas will experience more drag than those with smaller surface areas because they create more friction with the surrounding fluid. For example, a flat, wide object like a barn door will experience more drag than a narrow object like a pencil because it has a larger surface area. Similarly, a parachute will experience a large amount of drag because of its large surface area, which creates a significant amount of friction with the air molecules around it.In order to minimize drag and increase efficiency, engineers and designers often try to create streamlined objects with minimal surface area. This can be seen in the design of cars, airplanes, and even swimsuits used by competitive swimmers. By minimizing drag, these objects are able to move more quickly and with less effort through their respective fluids.

for such more questions on  resistance

https://brainly.com/question/28135236

#SPJ8

how does an atom of sulfur-36 become a sulfide ion with a -2 charge?

Answers

To understand how an atom of sulfur-36 becomes a sulfide ion with a -2 charge, because it has two more electrons than protons.

An atom of sulfur-36 has 16 electrons, 16 protons, and 20 neutrons. In order for the atom to become a sulfide ion with a -2 charge, it needs to gain two electrons. This is because when an atom gains or loses electrons, it becomes an ion with a positive or negative charge.

The atom of sulfur-36 becomes a sulfide ion with a -2 charge by gaining two electrons. These electrons come from another element, such as oxygen, which can give up two electrons to form an ionic bond with sulfur. The resulting compound is called sulfide, and it has a -2 charge because it now has two more electrons than protons.

An atom of sulfur-36 can become a sulfide ion with a -2 charge by gaining two electrons. This happens through an ionic bond with another element, such as oxygen, which gives up two electrons to form the compound. The resulting sulfide ion has a -2 charge because it has two more electrons than protons.

For more information on electrons kindly visit to

https://brainly.com/question/32031925

#SPJ11

what is the approximate boiling pressure of refrigerant oil in a system?

Answers

Refrigerant oil boiling pressure The boiling pressure of refrigerant oil is determined by the temperature of the system. This temperature varies depending on the pressure exerted on the oil. The refrigerant oil will boil at a different temperature for each refrigerant.

The boiling point of refrigerant oil can be estimated by determining the boiling pressure at a certain temperature of the system. The approximate boiling pressure of refrigerant oil in a system ranges from 20 to 30 psig. However, this value may vary depending on the type of refrigerant used in the system. The refrigerant oil can also be changed depending on the type of refrigerant used in the system.The type of refrigerant used in the system will also affect the boiling pressure of refrigerant oil. A refrigerant is a substance that changes from a liquid state to a gaseous state at a specific temperature. It is used in refrigeration systems to transfer heat from one location to another. The refrigerant oil is added to the system to ensure that all parts of the system are lubricated. This prevents the parts from grinding together and causing damage.

To know more about boiling pressure visit :

brainly.com/question/30512444

#SPJ11

A +13 nC charge is located at the origin.
A)What is the electric field at the position (x1,y1)=(5.0 cm, 0 cm)? Write electric field vector in component form.Enter the x and y components of the electric field separated by a comma. B)What is the electric field at the position (x2,y2)=(-5.0 cm, 5.0 cm)? Write electric field vector in component form.Enter the x and y components of the electric field separated by a comma.

Answers

Therefore, the electric field at the position (5.0 cm, 0 cm) is 1.144 N/C in the x-direction and the electric field at the position (-5.0 cm, 5.0 cm) is 0.468 N/C in both x and y directions.

A +13 nC charge is located at the origin. The expression to find the electric field at a given position is

E=KQ / r²,

where K is Coulomb's constant, Q is the charge and r is the distance between the charge and the point where we want to find the electric field.

So, A) The position at which electric field is to be calculated is

(x1,y1)= (5.0 cm, 0 cm).

Hence, distance

r = [tex]\sqrt{((5.0 cm)^{2} + (0 cm)^{2})}[/tex]

= 5.0 cm (as the point lies on x-axis).

Now, Electric field vector E = KQ / r²

= [tex]9 *10^{9} N.m² / C² * 13 * 10{-9}C / (5.0 * 10{-2} m)^{2}[/tex]

= 1.144 N/C

In component form, E = Exi + Eyj, where i and j are the unit vectors in the x and y directions respectively.

Therefore, E = Exi

= 1.144 N/C (as the electric field is only in the x-direction and there is no component of electric field in the y-direction)Hence, the main answer is: 1.144, 0

Electric field vector E = KQ / r²

= [tex]9 *10^{9} N.m² / C² * 13 * 10{-9}C / (5.0 * 10{-2} m)^{2}[/tex]

= 1.144 N/C

In component form, E = Exi + Eyj, where i and j are the unit vectors in the x and y directions respectively. Therefore,

E = Exi = 1.144 N/C (as the electric field is only in the x-direction and there is no component of electric field in the y-direction)B) The position at which electric field is to be calculated is (x2,y2)=(-5.0 cm, 5.0 cm).

Hence, distance

r = [tex]\sqrt{((-5.0 cm)^{2}+ (5.0 cm)^{2})}

= 7.07 cm.

Now, Electric field vector

E = KQ / r²

= [tex]9 *10^{9} N.m² / C² * 13 * 10{-9}C / (7.07 * 10{-2} m)^{2}[/tex]

= 0.659 N/C

In component form, E = Exi + Eyj, where i and j are the unit vectors in the x and y directions respectively.

Therefore, E = 0.468i + 0.468j (as the electric field makes an angle of 45° with both the x-axis and y-axis) answer is: 0.468

Therefore, the electric field at the position (5.0 cm, 0 cm) is 1.144 N/C in the x-direction and the electric field at the position (-5.0 cm, 5.0 cm) is 0.468 N/C in both x and y directions.

For more information on electric field  kindly visit to

https://brainly.com/question/14300841

#SPJ11

how deep is the shipwreck if echoes were detected 0.36 s after the sound waves were emitted?

Answers

If echoes were detected 0.36 s after the sound waves were emitted, the depth of the shipwreck is 65.52 meters. This can be calculated using the formula:distance = speed × timeWhere speed is the speed of sound in water, which is approximately 1481 meters per second.

The time is 0.36 seconds, as given in the problem.Therefore:

distance = speed × time

distance = 1481 × 0.36

distance = 532.56 meters

However, this distance is the total distance traveled by the sound wave, which includes both the distance from the ship to the bottom and the distance from the bottom to the surface. Since the sound wave travels twice this distance (down to the bottom and back up to the surface), we need to divide by 2 to find the depth of the shipwreck. So, the depth of the shipwreck is:

depth = distance / 2

depth = 532.56 / 2

depth = 265.28 meters

This means that the shipwreck is 265.28 meters deep.

For more information on shipwreck visit:

brainly.com/question/30244941

#SPJ11

determine the angular velocity of link bc at the instant shown. take ωab = 18 rad/s

Answers

According to the question we have the angular velocity of link BC at the instant shown is 0.06 rad/s.

Given, Angular velocity of link AB, ωAB = 18 rad/s Angular velocity of link BC, ωBC = ?We know that,For link AB:ωAB = θ˙1For link BC:ωBC = θ˙2For link CD:ωCD = θ˙3 .

We know that, Velocity analysis by instantaneous center method for mechanism given below: Velocity of link AB = Velocity of link BC Relative velocity of links AB and BC is given by:VAB/BC = NCWhere, NC is the perpendicular from the instantaneous center to the path of link BC.

VAB/BC = rA/RBC∴ rAωAB = RBCωBCrA/RBC = L1/L2 = 75/150 = 0.5 ∴ rA = 0.5RBCThe link BC moves downwards. Therefore, the perpendicular to the link BC will be in the upward direction and the perpendicular to link AB will be in the downward direction. Angular velocity of link BC = ωBC= rAωAB/RBC= 0.5×18/150= 0.06 rad/s

Therefore, the angular velocity of link BC at the instant shown is 0.06 rad/s.

To know more about Velocity  visit :

https://brainly.com/question/30559316

#SPJ11

(0)

If investors are enthusiastic about the future, the spread between yields on high-grade and low-grade bonds

Multiple Choice

1-stays the same.

2-increases.

3-None of these options are true.

4-decreases.

Answers

The answer is option 2 - increases. When investors are optimistic about the future, the demand for low-grade bonds falls, and the demand for high-grade bonds increases.

As a result, the price of high-grade bonds increases, causing the yield to decrease, and the price of low-grade bonds decreases, causing the yield to increase. The difference between the yields on high-grade and low-grade bonds, also known as the spread, increases as a result of this.

The spread is a measure of the risk associated with investing in a bond. When investors are optimistic, they are willing to take on more risk, resulting in a wider spread. Conversely, when investors are pessimistic, they are risk-averse, resulting in a narrower spread. Therefore, option 2 - increases is the correct answer.

To know more about Investors  visit :

https://brainly.com/question/31483087

#SPJ11

Calculate the work (kJ) done during a reaction in which the internal volume expands from 19 L to 48 L againts an outside pressure of 2.5 atm. W=-PdeltaV and atm.L= 101.235J
A) -7.3 kJ
B) 17 kJ
C) 7.3 kJ
D) -17 kJ
E) 0 kJ; No work is done

Answers

The work done during the reaction is approximately -7.3 kJ.

Hence, the correct option is A.

To calculate the work done during the reaction, we can use the formula:

W = -P * ΔV

Where:

W is the work done (in joules),

P is the external pressure (in atmospheres),

ΔV is the change in volume (in liters).

Given:

ΔV = 48 L - 19 L = 29 L

P = 2.5 atm

Substituting the values into the formula:

W = -2.5 atm * 29 L

Since 1 atm·L = 101.235 J, we can convert the units

W = -2.5 atm * 29 L * 101.235 J/(atmL)

W = -7365.08375 J

To convert the result to kilojoules, we divide by 1000:

W = -7.3 kJ

Therefore, the work done during the reaction is approximately -7.3 kJ. Hence, the correct option is A.

To know more about work done here

https://brainly.com/question/17032152

#SPJ4

what is the magnitude of the magnetic field in the shaded region

Answers

The magnitude of the magnetic field in the shaded region is determined as 1.3 T.

What is magnetic field?

A magnetic field is a picture that we use as a tool to describe how the magnetic force is distributed in the space around and within something magnetic.

Also, a magnetic field is a vector field in the neighborhood of a magnet, electric current, or changing electric field in which magnetic forces are observable.

From the given question, if the magnitude of the magnetic field is uniform, then, the value of the magnetic field in the shaded region will remain the same.

The magnitude of the magnetic field in the shaded region is calculated as follows;

B = B₀ x d₀/d₁

where;

B₀ is the initial magnetic fieldd is the distance of the charge

B = 1.3T  x 8 cm / 8 cm

B = 1.3 T

Learn more about magnitude of magnetic field here: https://brainly.com/question/30880745

#SPJ4

for the following exothermic reaction at equilibrium: h2o (g) co (g) co2(g) h2(g) decide if each of the following changes will increase the value of k (t = temperature)

Answers

For the given exothermic reaction at equilibrium:H2O(g) + CO(g) ⇌ CO2(g) + H2(g)Changes in pressure, temperature, or concentration may shift the equilibrium position, but they do not affect the value of Kc, which is constant for a given reaction at a given temperature. Hence, Kc is independent of any changes in the concentrations of reactants and products, as well as changes in the reaction conditions, as long as the temperature remains constant.To assess the effect of each change on the equilibrium constant, we must use Le Chatelier's principle to predict which direction the reaction will proceed to reestablish equilibrium. The shift in the equilibrium can cause Kc to vary when the system comes to equilibrium at the new conditions.A change in pressure will influence the equilibrium position of a gaseous reaction since gases are extremely responsive to pressure. If the pressure is increased on one side of an equilibrium reaction, the reaction will shift to the opposite side of the equation to balance the pressure. The equilibrium constant (Kc) will not change, but the pressure will influence the mole fractions of reactants and products, which will have an impact on the direction of the equilibrium shift and the rate at which it occurs. Increasing the pressure by decreasing the volume of the container in which the equilibrium reaction is occurring will result in a shift towards the side of the equation with fewer gas molecules, and the system will attempt to balance the pressure. Therefore, the reaction will shift to the left, resulting in a decrease in Kc. Since the reverse reaction, which is exothermic, is favored at lower temperatures, an increase in the value of Kc is not expected as the temperature is lowered. This means that the first option will not result in an increase in Kc. If the volume is increased, the reaction will shift towards the side with more gas molecules to compensate, resulting in an increase in Kc. This means that the second option will lead to an increase in Kc.

To know more about Le Chatelier's principle visit

https://brainly.com/question/29009512

#SPJ11

Exothermic reactions at equilibrium: In an exothermic reaction, the energy is released to the surrounding as heat. An exothermic reaction always has a negative sign for ΔH. An exothermic reaction at equilibrium means that the reactants and products are still reacting, but at the same rate. The reaction quotient, Qc, is equal to the equilibrium constant, Kc. The given exothermic reaction is: H2O (g) + CO (g) ⇌ CO2(g) + H2(g)The balanced equation is as follows: H2O(g) + CO(g) ⇌ CO2(g) + H2(g)Decide if each of the following changes will increase the value of K (T = temperature): Increasing the temperature The given reaction is exothermic.

An increase in temperature will favor the backward reaction and oppose the forward reaction to attain equilibrium. According to Le Chatelier’s principle, if stress is applied to an equilibrium system, it will react to counteract the effect of that stress. Hence, an increase in temperature will cause the equilibrium to shift towards the reactants, as it is an endothermic process. Therefore, the value of Kc will decrease. Decreasing the pressure CO and H2 are gaseous reactants, whereas CO2 and H2O are gaseous products. A decrease in pressure will favor the side of the reaction with more number of gaseous molecules to oppose the change. Therefore, the equilibrium will shift towards the reactants to balance the pressure. Hence, the value of Kc will increase. Adding a catalyst A catalyst is a substance that increases the rate of a chemical reaction by providing an alternative pathway for the reaction with a lower activation energy. A catalyst does not affect the equilibrium position of the reaction, but it helps in achieving the equilibrium state at a faster rate. Hence, adding a catalyst will not affect the value of Kc, as it is independent of the rate of the reaction. The following changes will increase the value of K (T = temperature): Decreasing the temperature Increasing the pressure Therefore, the decrease in temperature and increase in pressure will increase the value of Kc.

To get more information about Le Chatelier’s principle visit:

https://brainly.com/question/29009512

#SPJ11

the following appear on a physician's intake form. identify the level of measurement: (a) happiness on a scale of 0 to 10 (b) family history of illness (c) age (d) temperature

Answers

(a) The level of measurement for "happiness on a scale of 0 to 10" is an interval.

The happiness scale from 0 to 10 represents an interval measurement. The scale has equal intervals between the numbers, but it does not have a true zero point. The absence of happiness (0) does not indicate the complete absence of the attribute being measured. Therefore, it is an interval level of measurement.

(b) The level of measurement for "family history of illness" is nominal.

Family history of illness is a qualitative variable that represents categories or groups. It does not have a numerical order or magnitude. It is simply a classification of whether or not there is a family history of illness. Hence, it is a nominal level of measurement.

(c) The level of measurement for "age" is a ratio.

Age is a quantitative variable that has a meaningful zero point and a numerical order. Ratios between values are also meaningful. For example, someone who is 20 years old is half the age of someone who is 40 years old. Age satisfies all the properties of a ratio level of measurement.

(d) The level of measurement for "temperature" is an interval.

Temperature is a quantitative variable that can be measured on a scale such as Celsius or Fahrenheit. While temperature has equal intervals between the values, it does not have a true zero point (absolute absence of temperature). Therefore, it is an interval level of measurement.

To learn more about magnitude click here

https://brainly.com/question/29766788

#SPJ11

Why do rowers typically have the same number of paddles on each side of the boat?
a) It provides balance and symmetry in rowing.
b) It allows for efficient distribution of power.
c) It helps maintain stability and control.
d) All of the above

Answers

Rowers typically have the same number of paddles on each side of the boat because it provides balance and symmetry in rowing. The correct option is (a) It provides balance and symmetry in rowing.

Balance and symmetry are key components of effective rowing. When all rowers use the same number of paddles on each side of the boat, they create an evenly distributed power source that helps keep the vessel stable and on course. To maintain the balance and symmetry of the boat while rowing, the number of paddles on each side must be the same.

As a result, all rowers need to be coordinated and work together to ensure that their oars are in sync with one another. They should all have the same posture, the same rhythm, and the same intensity of strokes to ensure that they are not working against one another and instead, are working together to power the boat as efficiently as possible.In conclusion, rowers typically have the same number of paddles on each side of the boat to provide balance and symmetry in rowing.

To know more about balance  visit:-

https://brainly.com/question/27154367

#SPJ11

Our Sun, a type G star, has a surface temperature of 5800 K. We know, therefore, that it is cooler than a type O star and hotter than a type M star Othersportta coos tracking id: ST-630-45-4466-38345. In accordance with Expert TA's Terms of Service copying this information t 50% Part (a) How many times hotter than our Sun is the hottest type O star, which has a surface temperature of about 40,000 K? Number of times hotter sin() cos() tan() asin() acos() B12 SOAL atan() acotan() sinh() cotanh() tanh) Degrees O Radians cotan() cosh() (1) 7 4 1 Hint 8 9 5 6 2 3 + 0 VO CONCE . CLEAK Submit I give up! Hints: 0% deduction per hint. Hints remaining: 1 Feedback: 1% deduction per feedback. 50% Part (b) How many times hotter is our Sun than the coolest type M star, which has a surface temperature of 2400 K?

Answers

(a) The hottest type O star is approximately 6.90 times hotter than our Sun.

(b) Our Sun is approximately 2.42 times hotter than the coolest type M star.

How many times hotter than our Sun is the hottest type O star with a surface temperature of about 40,000 K, and how many times hotter is our Sun than the coolest type M star with a surface temperature of 2400 K?

Part (a) To determine how many times hotter the hottest type O star is compared to our Sun, we can calculate the temperature ratio as follows:

Temperature ratio = Temperature of the type O star / Temperature of our Sun

                = 40,000 K / 5,800 K

                ≈ 6.90

Therefore, the hottest type O star is approximately 6.90 times hotter than our Sun.

Part (b) To determine how many times hotter our Sun is compared to the coolest type M star, we can calculate the temperature ratio as follows:

Temperature ratio = Temperature of our Sun / Temperature of the type M star

                = 5,800 K / 2,400 K

                ≈ 2.42

Therefore, our Sun is approximately 2.42 times hotter than the coolest type M star.

Learn more about hottest type

brainly.com/question/30049280

#SPJ11

A box with a mass of 25 kg rests on a horizontal surface. The coefficient of static friction between the box and the surface is 0.20. What horizontal force must be applied to the box for it to start s

Answers

To start the box sliding along the surface in the positive x direction, a horizontal force greater than 49 N in the positive x direction must be applied.

The maximum static friction force can be calculated using the equation:

f_static_max = μ_static * N

where μ_static is the coefficient of static friction and N is the normal force acting on the box. In this case, since the box is on a horizontal surface, the normal force is equal to the weight of the box:

N = m * g

Substituting the given values:

N = 25 kg * 9.8 m/s² = 245 N

Now, we can determine the maximum static friction force:

f_static_max = 0.20 * 245 N = 49 N

This is the maximum force that can be exerted before the box starts sliding. Therefore, to overcome the static friction and initiate sliding in the positive x direction, a horizontal force greater than 49 N in the positive x direction must be applied. The exact value of the force will depend on the magnitude of the static friction and the force applied.

To know more about static friction refer here:

https://brainly.com/question/30886698#

#SPJ11

Complete Question:

A box with a mass of 25 kg rests on a horizontal surface. The coefficient of static friction between the box and the surface is 0.20. What horizontal force must be applied to the box for it to start sliding along the surface in the positive x direction? Use g = 9.8 m/s². O A horizontal force greater than 49 N in the positive x direction. O A horizontal force equal to 49 N in the positive x direction. O A horizontal force less than 49 N in the positive x direction. O A horizontal force that is either equal to or greater than 49 N in the positive x direction. O None of the other answers

Two parallel plates are held 10cm from one another. The potential difference between the plates is held at 100V. In this problem, ignore edge effects. (a) Find the electric field between the plates. (

Answers

The electric field between the plates is 1,000 V/m.

The electric field between parallel plates is given by the equation E = V/d, where E is the electric field, V is the potential difference, and d is the distance between the plates.

In this problem, the potential difference between the plates is 100V, and the distance between the plates is 10cm, which is equal to 0.1m.

Substituting these values into the equation, we have E = 100V / 0.1m = 1,000 V/m.

The electric field represents the force experienced by a unit positive charge placed between the plates. In this case, the electric field is constant and uniform between the plates since edge effects are ignored.

The electric field lines are directed from the positive plate to the negative plate.

The magnitude of the electric field is directly proportional to the potential difference between the plates and inversely proportional to the distance between the plates.

Therefore, increasing the potential difference or decreasing the distance between the plates will result in a stronger electric field.

To know more about "Electric field" refer here:

https://brainly.com/question/12118166#

#SPJ11

Other Questions
the small, semisolid mass of food formed during mastication is called a 1. i. Force is equal to mass x acceleration and is typically expressed in units of Newtons (kg m s-2). Acceleration is the rate of change of velocity. If gravitational acceleration is equal to 9.8 m s-2, then what is the gravitation force experienced by the mass of air in the box in: a. kg m s-2? b. Newtons (N)? (Note: again, this question does not involve a conversion but rather use of an equation.) ii. Pressure is equal to force divided by the area over which the force is applied and is typically expressed in units of Nm-2 (Pa). If the box from the previous questions rests on the Earth's surface, what is the pressure exerted by the gravitational force over the bottom area of the box (16 m2) in: a. N m-2? b. Pa? iii. Pressure on weather maps is usually expressed in units of bars, where one bar (100,000 Pa) approximates the average sea-level pressure (101,325 Pa or approximately 100,000 Pa). Using this and other aids (see appendix), convert 1 mb to Pa. determine the mean and variance of the random variable with the following probability mass function. f(x)=(64/21)(1/4)x, x=1,2,3 round your answers to three decimal places (e.g. 98.765). Arabian Gulf Corporation reports the following stockholders' equity section on December 31, 2020 - Common stock; $10 par value; 500,000 shares authorized; 200,000 shares issued and outstanding $ 2,000,000 - Paid in capital in excess of par value, common stock - Retained earnings... 400,000 900,000 Total $3,300,000 The Corporation completed the following transactions in 2021. 1-Jan 10, Directors declared a $1 per share cash dividend payable on March 15 to the Jan 31 stockholders of record 2- Mar 01, Purchased 10,000 shares of its own common for $15 per share. 3- Mar 15, Paid the cash dividend declared on Jan. 10. 4- May 01, Sold 6,000 of its treasury shares at $15 cash per share. 5- Sep 30, Directors declared a 30% stock dividend when the share market price is $16. 6- Nov 01, Distributed stock dividends declared on Sep. 30. 7- Nov 15, The company implemented 5-for-1 stock split for the common stock. Required: Prepare journal entries to record each of these transactions for 2021. In 2020, when the enacted tax rate for the current and all future periods was 27.5%, Garza Corp. had a taxable loss of $468,000 and elected to use the net operating loss carryforward provision.In 2021, the tax rate changed to 25.0% for the current and all future periods, and Garza reported taxable income of $311,000.In 2022, Garza reported taxable income of $664,000. Garza has no book-tax differences.What amount will Garza report as current income tax expense on its 2022 income statement? Computing job costs and overhead rate; assigning costs to inventory C1 P3 At the end of June, the job cost sheets at Ace Roofers show the following costs accumulated on three jobs. Additional information a. Job 5 was started in May, and the following costs were assigned to it in May: direct materials, $6,000; direct labor, $1,800; and applied overhead, $900. Job 5 was finished in June. c. b. Job 6 and Job 7 were started in June; Job 6 was finished in June, and Job 7 is to be completed in July. Overhead cost is applied with a predetermined rate based on direct labor cost. The predetermined overhead rate did not change across these months. Required 1. What is the total cost of direct materials requisitioned in June? 2. What is the total cost of direct labor used in June? 3. What is the predetermined overhead rate? 4. What is the total cost transferred to Finished Goods Inventory in June? I need help with the following assignment???? pleaseeeeDeliverable 3See Security Risk Assessment GuidelinesSecurity Risk Assessment Rubric (1)Security Risk Assessment Rubric (1)Criteria Ratings Pts This criterion is linked to a Learning OutcomeUnderstanding 15 pts Demonstrates a complete understanding of the topic and issues. Able to clearly and succinctly state the problem and issues. 5 pts Demonstrates an understanding of the topic and issues. Able to state the problem and most issues. 0 pts Demonstrates a confused or muddled understanding of the topic and issues. Unable to state the problem or issues. 15 pts This criterion is linked to a Learning OutcomeAnalysis & evaluation 15 pts Presents an insightful and thorough analysis of all issues identified. 5 pts Presents a thorough analysis of all issues identified. 0 pts Does not provide an adequate analysis of all issues. 15 pts This criterion is linked to a Learning OutcomeRecommendations 15 pts Supports recommendations with strong arguments and evidence; presents a balanced and critical view; interpretation is both reasonable and objective. Makes appropriate and powerful connections between the issues identified and the concepts studied in the course. 5 pts Supports recommendations with good arguments and evidence; interpretation is mostly reasonable and objective. Makes appropriate connections between the issues identified and the concepts studied in the course. 0 pts Recommendations are not provided or are supported with weak arguments and evidence; interpretation is questionable. Makes inappropriate connections or does not make any connection between the issues identified and the concepts studied in the course. 15 pts This criterion is linked to a Learning OutcomeCompleteness and consistency 10 pts Report is thorough and contains all necessary details and relevant data and information; extremely wellorganized and consistent formatting throughout. 5 pts Report includes most necessary details, data, and information; wellorganized and consistent formatting throughout. 0 pts Report does not includes most necessary details, data, and information; sloppy organization; inconsistent formatting throughout. 10 pts This criterion is linked to a Learning OutcomeGrammar & Spelling 10 pts The submission was free from spelling and grammatical errors. 6 pts The submission contained fewer than three spelling and grammatical errors. 0 pts The submission contained three or more spelling and grammatical errors. 10 pts This criterion is linked to a Learning OutcomeAPA 10 pts Uses APA guidelines accurately and consistently to cite sources 0 pts Sources were not cited per APA. Reference list not provided or did not follow APA guidelines. In 2014, the per capita GDP of the five richest countries was 70 times higher than that of the five poorest, i.e. y rich/y poor = 70. if Ak^1/3 and (k rich/k poor)^1/3 = 5, then the ratio of TFPs across countries, rich /Apoor' , to explain income differences is A. 1 B. 5 C. 14 D. 48 E. 77 What are 5 key terms that describe cloud computing Question 2 (8 marks) A fruit growing company claims that only 10% of their mangos are bad. They sell the mangos in boxes of 100. Let X be the number of bad mangos in a box of 100. (a) What is the dist .Problem 7-40 (LO. 5)Blue Corporation, a manufacturing company, decided to develop a new line of merchandise. The project began in 2019. Blue had the following expenses in connection with the project:20192020Salaries$500,000$600,000Materials90,00070,000Insurance8,00011,000Utilities6,0008,000Cost of inspection of materials for quality control7,0006,000Promotion expenses11,00018,000Advertising020,000Equipment depreciation15,00014,000Cost of market survey8,0000Question Content AreaThe new product will be introduced for sale beginning in July 2021. Determine the amount of the deduction for research and experimental expenditures for 2019, 2020, 2021, and 2022.If an amount is zero, enter "0". Calculate the monthly expense to the nearest dollar and use in subsequent computations.a. If Blue Corporation elects to expense the research and experimental expenditures, what will the amount of the deduction be?201920202021 and 2022Amount of the deduction$ 619,000$703,000$ 0b. If Blue Corporation elects to amortize the research and experimental expenditures over 60 months, what will the amount of the deduction be?2019202020212022Amount of the deduction$ 0$ 0$132,198$264,396c. How would your answer change if Blue Corporation incurred the expenses in 2022 and 2023 (rather than 2019 and 2020)?20222023Amount of the deduction$?$? How fast do you have to throw the rock so that it never comes back to the asteroid and ends up traveling at a speed of 10 m/s when it is very far away? When preparing the report to analyze a proposed quality improvement program, which of the following costs are included in the total costs of not undertaking the quality improvement program?A.inspection of finished goodsB.preventive maintenanceC.sales returnsD.total appraisal costs distinguish between the exocrine and endocrine secretions of the pancreas What data should be plotted to show that experimental concentration data fits a zero-order reaction? Select one: a. 1/[reactant) vs. time b. In(k) vs. Ea c. In(k) vs. 1/T d. In[reactant] vs. time e. [reactant) vs. time Let's say you want to construct a 90% confidence interval forthe true proportion of voters who support Karol for city treasurer.Previously, it is estimated that 60% support Karol. How large doesthe For each of the following strong base solutions, determine [OH][OH] and [H3O+][H3O+] and pHpH and pOHpOH.For 5.21045.2104 MM Ca(OH)2Ca(OH)2, determine [OH][OH] and [H3O+][H3O+]. When applying the co-terminated assumption: A study period equal to the minimum common multiple of the lives of the two alternatives is selected and used to evaluate both alternatives Each alternative is evaluated with its own study period which is equal to its life time A study period equal to the average of the life times of both alternatives is selected to be able to compare them with economic equivalence methods O A study period equal to the life of one of the alternatives is selected, and the life of the other alternative is adjusted to the same study period Kindly assist me with specific objectives/research questionsunder this general objective "to establish the effects of e-bankingon customer service delivery". What process in plant cells is similar to animals eating food for energy?A.Vacuoles storing energy for later use in plant growthB.Chloroplasts using radiant energy to allow the cell to function.C.Ribosomes moving energy to different parts of the cell.D.Nuclei create DNA to use to make new plant cells.