Answer:
41.2°
Explanation:
Total internal reflection is the reflection of the incident ray at the interface between two media in which one of the media has a lower refractive index than the other. It occurs when the angle of incidence in the denser medium exceeds the critical angle.
The critical angle is the angle of incidence in the denser medium when the angle of incidence in the less dense medium is 90°.
Since
n= 1/sin C
C= sin^-(1/n)
C= sin^-(1/1.33)
C= 48.8°
Hence angle of incidence= 90-48.8 = 41.2°
Compare the value for the inductor when the current was increasing vs decreasing. Which statement matches the expected results. The inductance should be the same regardless of whether the current is increasing or decreasing. The inductance should be greater while the current is increasing. The inductance should be greater while the current is decreasing.
Answer:
see that the inductance depends on the variation with respect to time of the current, therefore it is independent, increase decreases,
Explanation:
The express for inductance is
[tex]E_{L}[/tex]= L dI / dt
L = E_{L} (di / dt)⁻¹
where L is the inductance, E_{L} the induced electromotive force, di/dt the variation of the current as a function of time.
When analyzing this equation we see that the inductance depends on the variation with respect to time of the current, therefore it is independent, increase decreases,
Correct answer the inductance must be the same regardless of whether the current increases or decreases.
An object is placed in a fluid and then released. Assume that the object either floats to the surface (settling so that the object is partly above and partly below the fluid surface) or sinks to the bottom. Answer the following question:
The magnitude of the buoyant force is equal to the weight of fluid displaced by the object. Under what circumstances is this statement true?
a. for every object submerged partially or completely in a fluid
b. only for an object that is floating
c. only for an object that is fully submerged and is sinking.
d. for no object submerged in a fluid
Answer:
Answer:
A. for every object submerged partially or completely in a fluid
Explanation:
This is following Archimedes principle which states that the upward buoyant force that is exerted on a body immersed in a fluid, whether FULLYor PARTIALLY submerged, is equal to the weight of the fluid that the body displaces.
Explanation:
Intelligent beings in a distant galaxy send a signal to earth in the form of an electromagnetic wave. The frequency of the signal observed on earth is 2.2% greater than the frequency emitted by the source in the distant galaxy. What is the speed vrel of the galaxy relative to the earth
Answer:
Vrel= 0.75c
Explanation:
See attached file
What is the reason for the increase and decrease size of the moon and write down in a paragraph.
Answer:
The reason for the increase or decrease of the moon is due to the angular perception of the moon.
Explanation:
Also called lunar illusion, this phenomenon is due to the position in which the moon is, it can be at the zenith or on the horizon, both distances are different from each other with respect to the position of the person.
The zenith is the highest part of the sky and the horizon the lowest.
When there are landmarks such as trees, buildings or mountains on the horizon, the illusion of closeness is given and the illusion of distance is misinterpreted.
But when looking up at the sky as there is no reference point there will be a failure in the perception of size.
A system gains 767 kJ of heat, resulting in a change in internal energy of the system equal to +151 kJ. How much work is done?
Answer:
The work done on the system is -616 kJ
Explanation:
Given;
Quantity of heat absorbed by the system, Q = 767 kJ
change in the internal energy of the system, ΔU = +151 kJ
Apply the first law of thermodynamics;
ΔU = W + Q
Where;
ΔU is the change in internal energy
W is the work done
Q is the heat gained
W = ΔU - Q
W = 151 - 767
W = -616 kJ (The negative sign indicates that the work is done on the system)
Therefore, the work done on the system is -616 kJ
At TTT = 14 ∘C∘C, how long must an open organ pipe be to have a fundamental frequency of 262 HzHz ? The speed of sound in air is v≈(331+0.60T)m/sv≈(331+0.60T)m/s, where TT is the temperature in ∘C∘C.
Answer:
Length of pipe organ(L) = 0647 m (Approx)
Explanation:
Given:
Temperature (T) = 14°C
Fundamental frequency (F) = 262 Hz
Speed of sound (v) = 331 + 0.60(T) m/s
Find:
Length of pipe organ(L)
Computation:
Speed of sound (v) = 331 + 0.60(14) m/s
Speed of sound (v) = 339.4
Length of pipe organ(L) = Speed of sound (v) / 2(Fundamental frequency)
Length of pipe organ(L) = 339.4 / 2 (262)
Length of pipe organ(L) = 0647 m (Approx)
A 5.0 kg block hangs from a spring with spring constant 2000 N/m. The block is pulled down 5.0 cm from the equilibrium position and given an initial velocity of 1.0 m/s back towards equilibrium. a) What is the total mechanical energy of the motion
Answer:
Explanation:i think this would help u
IMPORTANT ANSWER ALL 3 PLEASE!
Answer:
4. Liters
5. Celsius
6. Grams
A projectile is shot from the edge of a cliff 80 m above ground level with an initial speed of 60 m/sec at an angle of 30° with the horizontal. Determine the time taken by the projectile to hit the ground below.
Answer:
8 seconds
Explanation:
Answer:
Explanation:
Going up
Time taken to reach maximum height= usin∅/g
=3 secs
Maximum height= H+[(usin∅)²/2g]
=80+[(60sin30)²/20]
=125 meters
Coming Down
Maximum height= ½gt²
125= ½(10)(t²)
t=5 secs
In order to waken a sleeping child, the volume on an alarm clock is doubled. Under this new scenario, how much more energy will be striking the child's ear drums each second?
Answer:4 times more energy will be striking the childbearing
Explanation:
Because Volume is directly proportional to amplitude of sound. Energy is proportional to amplitude squared. If you triple the amplitude, you multiply the energy by 4
The charger for your electronic devices is a transformer. Suppose a 60 Hz outlet voltage of 120 V needs to be reduced to a device voltage of 3.0 V. The side of the transformer attached to the electronic device has 45 turns of wire.
How many turns are on the side that plugs into the outlet?
Answer:
N₁ = 1800 turns
So, the side of the transformer that plugs into the outlet has 1800 turns.
Explanation:
The transformer turns ratio is given by the following equation:
V₁/V₂ = N₁/N₂
where,
V₁ = Voltage of outlet = 120 V
V₂ = Device Voltage = 3 V
N₁ = No. of turns on outlet side = ?
N₂ = No. of turns on side of device = 45
Therefore,
120 V/3 V = N₁/45
N₁ = (40)(45)
N₁ = 1800 turns
So, the side of the transformer that plugs into the outlet has 1800 turns.
A damped oscillator is released from rest with an initial displacement of 10.00 cm. At the end of the first complete oscillation, the displacement reaches 9.05 cm. When 4 more oscillations are completed, what is the displacement reached
Answer:
The displacement is [tex]A_r = 6.071 \ cm[/tex]
Explanation:
From the question we are told that
The initial displacement is [tex]A_o = 10 \ cm[/tex]
The displacement at the end of first oscillation is [tex]A_d = 9.05 \ cm[/tex]
Generally the damping constant of this damped oscillator is mathematically represented as
[tex]\eta = \frac{A_d}{A_o}[/tex]
substituting values
[tex]\eta = \frac{9.05}{10}[/tex]
[tex]\eta = 0.905[/tex]
The displacement after 4 more oscillation is mathematically represented as
[tex]A_r = \eta^4 * A_d[/tex]
substituting values
[tex]A_r = (0.905)^4 * (9.05)[/tex]
[tex]A_r = 6.071 \ cm[/tex]
Answer:
Displacement reached is 6.0708 cm
Explanation:
Formula for damping Constant "C"
[tex]C^n=\frac{A_2}{A_1}[/tex] where n=1,2,3,........n
Where:
[tex]A_2[/tex] is the displacement after first oscillation
[tex]A_1\\[/tex] is the initial Displacement
[tex]A_1=10\ cm\\A_2=9.05\ cm\\[/tex]
In our case, n=1.
[tex]C=\frac{9.05}{10}\\C=0.905[/tex]
After 4 more oscillation, n=4:
[tex]C^4=\frac{A_6}{A_2}[/tex]
Where:
[tex]A_6[/tex] is the final Displacement after 4 more oscillations.
[tex]A_6=(0.905)^4*(9.05)\\A_6=6.0708\ cm[/tex]
Displacement reached is 6.0708 cm
What is 3/4 of 12 and 24
Answer:
3/4 of 12 = 16
3/4 of 24 = 32
Those are the answers based on how your question sounded
Explanation:
Answer:
27
Explanation:
3/4 of (12 and 24)
of means ×
and means +
therefore,3/4× (12+24)
3/4×(36)
3×9
27
An object is placed in a room where the temperature is 20 degrees C. The temperature of the object drops by 5 degrees C in 4 minutes and by 7 degrees C in 8 minutes. What was the temperature of the object when it was initially placed in the room
Answer:
28.3°C
Explanation:
Using
T(t) = (T(0) - 20)*(e^(-k*t)) + 20
for some positive number k, and some initial temperature T(0).
Boundary conditions:
T(4) = T(0) - 5 _______ (i)
T(8) = T(0) - 7 _______ (ii)
==> solving for T(0) and k :
(i):
(T(0) - 20)*(e^(-k*4)) + 20 = T(0) - 5 ==>
(T(0) - 20)*(e^(-k*4)) = T(0) - 20 - 5
(T(0) - 20)*(e^(-k*4)) = (T(0) - 20) - 5
5 = (T(0) - 20) - (T(0) - 20)*(e^(-k*4))
5 = (T(0) - 20) * ( 1 - e^(-k*4) )
(ii):
(T(0) - 20)*(e^(-k*8)) + 20 = T(0) - 7
(T(0) - 20)*(e^(-k*8)) = (T(0) - 20) - 7
7 = (T(0) - 20) - (T(0) - 20)*(e^(-k*8))
7 = (T(0) - 20) * (1 - e^(-k*8))
In both results, subsitute x = e^(-4k) and C = (T(0) - 20)
(i): 5 = C * (1 - x)
(ii): 7 = C * (1 - x^2) = C * (1-x)*(1+x)
Substitute C*(1-x) from (i) into (ii):
(ii): 7 = 5*(1+x) ==> (1+x) = 7/5 ==> x = 2/5
back into (i):
(i): 5 = C * (1 - 2/5) ==> 5 = C * 3/5 ==> C = 25/3
C = T(0) - 20 ==>
T(0) = C + 20 = 25/3 + 20 = 25/3 + 60/3 = 85/3
= 28.3°C
Given a double slit apparatus with slit distance 2 mm, what is the theoretical maximum number of bright spots that I would see when I shine light with a wavelength 500 nm on the slits
Answer:
The values is [tex]m_{max} = 8001 \ bright \ spots[/tex]
Explanation:
From the question we are told that
The slit distance is [tex]d = 2 \ mm = 2*10^{-3} \ m[/tex]
The wavelength is [tex]\lambda = 500 \ nm = 500 *10^{-9} \ m[/tex]
At the first half of the screen from the central maxima
The number of bright spot according to the condition for constructive interference is
[tex]n = \frac{d * sin (\theta )}{\lambda}[/tex]
For maximum number of spot [tex]\theta = 90^o[/tex]
So
[tex]n = \frac{2*10^{-3} * sin (90 )}{500 *10^{-9}}[/tex]
[tex]n =4000[/tex]
Now for the both sides plus the central maxima we have
[tex]m_{max} = 2 * n + 1[/tex]
substituting values
[tex]m_{max} = 2 * 4000 + 1[/tex]
[tex]m_{max} = 8001 \ bright \ spots[/tex]
A person, with his ear to the ground, sees a huge stone strike the concrete pavement. A moment later two sounds are heard from the impact: one travels in the air and the other in the concrete, and they are 0.50 s apart. The speed of sound in air is 343 m/s, and in concrete is 3000 m/s.
Required:
How far away did the impact occur?
Answer:
The distance is [tex]d = 193.6 \ m[/tex]
Explanation:
From the question we are told that
The time interval between the sounds is k[tex]t_1 = k + t_2[/tex] = 0.50 s
The speed of sound in air is [tex]v_s = 343 \ m/s[/tex]
The speed of sound in the concrete is [tex]v_c = 3000 \ m/s[/tex]
Generally the distance where the collision occurred is mathematically represented as
[tex]d = v * t[/tex]
Now from the question we see that d is the same for both sound waves
So
[tex]v_c t = v_s * t_1[/tex]
Now
So [tex]t_1 = k + t[/tex]
[tex]v_c t = v_s * (t+ k)[/tex]
=> [tex]3000 t = 343* (t+ 0.50)[/tex]
=> [tex]3000 t = 343* (t+ 0.50)[/tex]
=> [tex]t = 0.0645 \ s[/tex]
So
[tex]d = 3000 * 0.0645[/tex]
[tex]d = 193.6 \ m[/tex]
The work function of a certain metal is φ = 3.55 eV. Determine the minimum frequency of light f0 for which photoelectrons are emitted from the metal. (Planck's constant is: h = 4.1357×10-15 eVs.)
Answer:
Explanation:
Let f₀ be the frequency .
energy of photons having frequency of f₀
= hf₀ where h is plank's constant
for electron to get ejected , work function should be equal to energy of photon
hf₀ = 3.55
4.1357 x 10⁻¹⁵ x f₀ = 3.55
f₀ = 8.58 x 10¹⁴ Hz .
A 25 cm diameter circular saw blade spins at 3500 rpm. How fast would you have to push a straight hand saw to have the teeth move through the wood at the same rate as the circular saw teeth
Answer:
The answer is "45.79 m/s"
Explanation:
Given values:
diameter= 25 cm
w= 3500 rpm
Formula:
[tex]\boxed{v=w \times r} \ \ \ \ \ \ _{where} \ \ \ w = \frac{rad}{s} \ \ \ and \ \ \ r = meters[/tex]
Calculating r:
[tex]r= \frac{diameter}{2}[/tex]
[tex]=\frac{25}{2}\\\\=12.5 \ cm[/tex]
converting value into meters: [tex]12.5 \times 10^{-2} \ \ meter[/tex]
calculating w:
[tex]w= diameter \times \frac{2\pi}{60}\\[/tex]
[tex]= 3500 \times \frac{2\times 3.14}{60}\\\\= 3500 \times \frac{2\times 314}{6000}\\\\= 35 \times \frac{314}{30}\\\\= 35 \times \frac{314}{30}\\\\=\frac{10990}{30}\\\\=\frac{1099}{3}\\\\=366.33[/tex]
w= 366.33 [tex]\ \ \frac{rad}{s}[/tex]
Calculating v:
[tex]v= w\times r\\[/tex]
[tex]= 366.33 \times 12.5 \times 10^{-2}\\\\= 366.33 \times 12.5 \times 10^{-2}\\\\= 4579.125 \times 10^{-2}\\\\\boxed{=45.79 \ \ \frac{m}{s}}[/tex]
an electromagnetic wave propagates in a vacuum in the x-direction. In what direction does the electric field oscilate
Answer:
The electric field can either oscillates in the z-direction, or the y-direction, but must oscillate in a direction perpendicular to the direction of propagation, and the direction of oscillation of the magnetic field.
Explanation:
Electromagnetic waves are waves that have an oscillating magnetic and electric field, that oscillates perpendicularly to one another. Electromagnetic waves are propagated in a direction perpendicular to both the electric and the magnetic field. If the wave is propagated in the x-direction, then the electric field can either oscillate in the y-direction, or the z-direction but must oscillate perpendicularly to both the the direction of oscillation of the magnetic field, and the direction of propagation of the wave.
Currents in DC transmission lines can be 100 A or higher. Some people are concerned that the electromagnetic fields from such lines near their homes could pose health dangers.
A. For a line that has current 150 A and a height of 8.0 m above the ground, what magnetic field does the line produce at ground level? Express your answer in teslas.
B. What magnetic field does the line produce at ground level as a percent of earth's magnetic field which is 0.50 G?
C. Is this value of magnetic field cause for worry? Choose your answer below.
i. Yes. Since this field does not differ a lot from the earth's magnetic field, it would be expected to have almost the same effect as the earth's field.
ii. No. Since this field is much lesser than the earth's magnetic field, it would be expected to have less effect than the earth's field.
iii. Yes. Since this field is much greater than the earth's magnetic field, it would be expected to have more effect than the earth's field.
iv. No. Since this field does not differ a lot from the earth's magnetic field, it would be expected to have almost the same effect as the earth's field.
Answer:
Explanation:
magnetic field due to an infinite current carrying conductor
B = k x 2I / r where k = 10⁻⁷ , I is current in conductor and r is distance from wire
putting the given data
B = 10⁻⁷ x 2 x 100 / 8
= 25 x 10⁻⁷ T .
B )
earth's magnetic field = .5 gauss
= .5 x 10⁻⁴ T
= 5 x 10⁻⁵ T
percent required = (25 x 10⁻⁷ / 5 x 10⁻⁵) x 100
= 5 %
C )
ii. No. Since this field is much lesser than the earth's magnetic field, it would be expected to have less effect than the earth's field.
A 2.0 m × 4.0 m flat carpet acquires a uniformly distributed charge of −10 μC after you and your friends walk across it several times. A 5.0 μg dust particle is suspended in midair just above the center of the carpet.
Required:
What is the charge on the dust particle?
Answer:
The charge on the dust particle is [tex]q_d = 6.94 *10^{-13} \ C[/tex]
Explanation:
From the question we are told that
The length is [tex]l = 2.0 \ m[/tex]
The width is [tex]w = 4.0 \ m[/tex]
The charge is [tex]q = -10\mu C= -10*10^{-6} \ C[/tex]
The mass suspended in mid-air is [tex]m_a = 5.0 \mu g = 5.0 *10^{-6} \ g = 5.0 *10^{-9} \ kg[/tex]
Generally the electric field on the carpet is mathematically represented as
[tex]E = \frac{q}{ 2 * A * \epsilon _o}[/tex]
Where [tex]\epsilon _o[/tex] is the permittivity of free space with value [tex]\epsilon_o = 8.85*10^{-12} \ \ m^{-3} \cdot kg^{-1}\cdot s^4 \cdot A^2[/tex]
substituting values
[tex]E = \frac{-10*10^{-6}}{ 2 * (2 * 4 ) * 8.85*10^{-12}}[/tex]
[tex]E = -70621.5 \ N/C[/tex]
Generally the electric force keeping the dust particle on the air equal to the force of gravity acting on the particles
[tex]F__{E}} = F__{G}}[/tex]
=> [tex]q_d * E = m * g[/tex]
=> [tex]q_d = \frac{m * g}{E}[/tex]
=> [tex]q_d = \frac{5.0 *10^{-9} * 9.8}{70621.5}[/tex]
=> [tex]q_d = 6.94 *10^{-13} \ C[/tex]
A small insect viewed through a convex lens is 1.5 cmcm from the lens and appears 2.5 times larger than its actual size. Part A What is the focal length of the lens
Answer:
The focal length of the lens is 2.5 cm
Explanation:
Use the two equations for thin lenses combined: the one for magnification (m), and the one that relates distances of object [tex]d_o[/tex], of image [tex]d_i[/tex], and focal length;
[tex]m=\frac{h_i}{h_o} =-\frac{d_i}{d_o} \\ \\\frac{1}{d_i} +\frac{1}{d_o} =\frac{1}{f}[/tex]
Since we know the value of the magnification (m), we can write the image distance in terms of the object distance, and then use it to replace the image distance in the second equation:
[tex]m=-\frac{d_i}{d_o} \\2.5=-\frac{d_i}{d_o}\\d_i=-2.5\,d_o[/tex]
then, solving for the focal distance knowing that the object distance is 1.5 cm:
[tex]\frac{1}{d_i} +\frac{1}{d_o} =\frac{1}{f}\\-\frac{1}{2.5\,d_o} +\frac{1}{d_o} =\frac{1}{f}\\(2.5\,d_o\,f)\,(-\frac{1}{2.5\,d_o} +\frac{1}{d_o}) =\frac{1}{f}\,(2.5\,d_o\,f)\\-f+2.5\,f=2.5\,d_o\\1.5\,f=2.5\,d_o\\f=\frac{2.5\,d_o}{1.5} \\f=\frac{2.5\,(1.5\,\,cm)}{1.5}\\f=2.5\,\,cm[/tex]
An airplane flies 1,592 miles east from Phoenix, Arizona, to Atlanta, Georgia, in 3.68 hours.
What is the average velocity of the airplane? Round your answer to the nearest whole number.
Answer:
433
Explanation:
the charge density in an insulateed solid sphere of radius find the electric field at a distance of from the center of the solid
Answer:
Assuming the charged density in the insulated solid sphere of radius 3.1m is 8.8e-9, the electric field at 5.2 meters is 73.1256 [tex]i[/tex].
Explanation:
The electric charge linear density is equal to 8.8 x[tex]10^{-9}[/tex]
the radius of the sphere is 3.1m
The magnitude of the electric field at the radius of the sphere equal to 5.2 meters can be calculated with the formula ;
- E = λ / 4πε₀ [ r / α ( α + r ) ] [tex]i[/tex]
Solution:
E = 8.8 x[tex]10^{-9}[/tex] / 4πε₀ [ 3.1/ 5.2( 5.2 + 3.1) ] [tex]i[/tex]
= 1018.0995 [0.07183] [tex]i[/tex]
= 73.1256 [tex]i[/tex]
Determine the orbital period (in hours) of an observation satellite in a circular orbit 1,787 km above Mars.
Answer:
T = 3.14 hours
Explanation:
We need to find the orbital period (in hours) of an observation satellite in a circular orbit 1,787 km above Mars.
We know that the radius of Mars is 3,389.5 km.
So, r = 1,787 + 3,389.5 = 5176.5 km
Using Kepler's law,
[tex]T^2=\dfrac{4\pi ^2}{GM}r^3[/tex]
M is mass of Mars, [tex]M=6.39\times 10^{23}\ kg[/tex]
So,
[tex]T^2=\dfrac{4\pi ^2}{6.67\times 10^{-11}\times 6.39\times 10^{23}}\times (5176.5 \times 10^3)^3\\\\T=\sqrt{\dfrac{4\pi^{2}}{6.67\times10^{-11}\times6.39\times10^{23}}\times(5176.5\times10^{3})^{3}}\\\\T=11334.98\ s[/tex]
or
T = 3.14 hours
So, the orbital period is 3.14 hours
HELP!!! 35 point question. answer at least 3 correctly. please include equations and how you did it
Answer:
9. (B) ¼ Mv²
10. (A) √(3gL)
11. 20 N
12. 5 m/s²
Explanation:
9. The rotational kinetic energy is:
RE = ½ Iω²
RE = ½ (½ MR²) (v/R)²
RE = ¼ Mv²
10. Energy is conserved.
Initial potential energy = rotational energy
mgh = ½ Iω²
Mg(L/2) = ½ (⅓ ML²) ω²
g(L/2) = ½ (⅓ L²) ω²
gL = ⅓ L² ω²
g = ⅓ L ω²
ω² = 3g / L
ω = √(3g / L)
The velocity of the top end is:
v = ωL
v = √(3gL)
11. Sum of torques about the hinge:
∑τ = Iα
-(Mg) (L/2) + (T) (r) = 0
T = MgL / (2r)
T = (3.00 kg) (10 m/s²) (1.60 m) / (2 × 1.20 m)
T = 20 N
12. Sum of forces on the block in the -y direction:
∑F = ma
mg − T = ma
Sum of torques on the pulley:
∑τ = Iα
TR = (½ MR²) (a / R)
T = ½ Ma
Substitute:
mg − ½ Ma = ma
mg = (m + ½ M) a
a = mg / (m + ½ M)
Plug in values:
a = (3.0 kg) (10 m/s²) / (3.0 kg + ½ (6.0 kg))
a = 5 m/s²
Suppose a certain laser can provide 82 TW of power in 1.1 ns pulses at a wavelength of 0.24 μm. How much energy is contained in a single pulse?
Answer:
The energy contained in a single pulse is 90,200 J.
Explanation:
Given;
power of the laser, P = 82 TW = 82 x 10¹² W
time taken by the laser to provide the power, t = 1.1 ns = 1.1 x 10⁻⁹ s
the wavelength of the laser, λ = 0.24 μm = 0.24 x 10⁻⁶ m
The energy contained in a single pulse is calculated as;
E = Pt
where;
P is the power of each laser
t is the time to generate the power
E = (82 x 10¹²)(1.1 x 10⁻⁹)
E = 90,200 J
Therefore, the energy contained in a single pulse is 90,200 J
A simple series circuit consists of a 120 Ω resistor, a 21.0 V battery, a switch, and a 3.50 pF parallel-plate capacitor (initially uncharged) with plates 5.0 mm apart. The switch is closed at t =0s .
Required:
a. After the switch is closed, find the maximum electric flux through the capacitor.
b. After the switch is closed, find the maximum displacement current through the capacitor.
c. Find the electric flux at t =0.50ns.
d. Find the displacement current at t =0.50ns.
Answer
Integral EdA = Q/εo =C*Vc(t)/εo = 3.5e-12*21/εo = 4.74 V∙m <----- A)
Vc(t) = 21(1-e^-t/RC) because an uncharged capacitor is modeled as a short.
ic(t) = (21/120)e^-t/RC -----> ic(0) = 21/120 = 0.175A <----- B)
Q(0.5ns) = CVc(0.5ns) = 2e-12*21*(1-e^-t/RC) = 30.7pC
30.7pC/εo = 3.47 V∙m <----- C)
ic(0.5ns) = 29.7ma <----- D)
What is the displacement of the object after 3 seconds?
Answer:
3 meters
Explanation:
A radar pulse returns 3.0 x 10-4 seconds after it is sent out, having been reflected by an object. What is the distance between the radar antenna and the object
Answer:
The distance is [tex]D = 45000 \ m[/tex]
Explanation:
From the question we are told that
The time taken is [tex]t = 3.0 *10^{-4 } \ s[/tex]
Generally the speed of the radar is equal to the speed of light and this has a value
[tex]c = 3.0*10^{8} \ m /s[/tex]
Now the distance covered by the to and fro movement of the radar is mathematically evaluated as
[tex]d = c * t[/tex]
=> [tex]d = 3.0*10^{8} * 3.0*10^{-4}[/tex]
=> [tex]d = 90000 \ m[/tex]
Therefore the distance between the radar antenna and the object is
[tex]D = \frac{d}{2}[/tex]
[tex]D = \frac{ 90000}{2}[/tex]
[tex]D = 45000 \ m[/tex]
The distance between the radar antenna and the object will be 45000 m.
What is a radar antenna?A radar antenna is a device that sends out radio waves and listens for their reflections. The ability of an antenna to identify the exact direction in which an item is placed determines its performance.
The given data in the problem is;
t is the time= 3.0 x 10⁻⁴
d is the distance between the radar antenna and the object=?
c is the peed of light=3×10⁸ m/sec
The radar's speed is usually equal to the speed of light, and this has a value. The distance covered by the radars to and fro movement is now calculated mathematically as
[tex]\rm d= c \times t \\\\ \rm d= 3.0 \times 10^8 \times 3.0 \times 10^{-4} \\\\ d=90000 \ m[/tex]
As a result, the radar antenna's distance from the target is
[tex]\rm D=\frac{d}{2} \\\\ \rm D=\frac{90000}{2} \\\\ \rm D=\ 45000 \ m[/tex]
Hence the distance between the radar antenna and the object will be 45000 m.
To learn more about the radar antena refer to the link;
https://brainly.com/question/24067190
