A fixed 11.2-cm-diameter wire coil is perpendicular to a magnetic field 0.53 T pointing up. In 0.10 s , the field is changed to 0.24 T pointing down. What is the average induced emf in the coil?

Answers

Answer 1

Answer:

The average induced emf in the coil is 0.0286 V

Explanation:

Given;

diameter of the wire, d = 11.2 cm = 0.112 m

initial magnetic field, B₁ = 0.53 T

final magnetic field, B₂ = 0.24 T

time of change in magnetic field, t = 0.1 s

The induced emf in the coil is calculated as;

E = A(dB)/dt

where;

A is area of the coil = πr²

r is the radius of the wire coil = 0.112m / 2 = 0.056 m

A = π(0.056)²

A = 0.00985 m²

E = -0.00985(B₂-B₁)/t

E = 0.00985(B₁-B₂)/t

E = 0.00985(0.53 - 0.24)/0.1

E = 0.00985 (0.29)/ 0.1

E = 0.0286 V

Therefore, the average induced emf in the coil is 0.0286 V

Answer 2

We have that for the Question, it can be said that the average induced emf in the coil is

E=0.028565V

From the question we are told

A fixed 11.2-cm-diameter wire coil is perpendicular to a magnetic field 0.53 T pointing up. In 0.10 s , the field is changed to 0.24 T pointing down. What is the average induced emf in the coil?

Generally the equation for the Average emf induced   is mathematically given as

[tex]Emf_a=-NA\frac{dB}{dt}\\\\Where\\\\Area\\\\a=\pir^2\\\\a=\pi(0.056)^2\\\\a=0.00985\\\\[/tex]

Hence

[tex]dB=0.24-0.53\\\\dB=-0.29T[/tex]

Therefore

[tex]E=-\frac{1*0.00985*-0.29 }{0.10}[/tex]

E=0.028565V

For more information on this visit

https://brainly.com/question/23379286


Related Questions

Three resistors, each having a resistance, R, are connected in parallel to a 1.50 V battery. If the resistors dissipate a total power of 3.00 W, what is the value of R

Answers

Answer:

The value of resistance of each resistor, R is 2.25 Ω

Explanation:

Given;

voltage across the three resistor, V = 1.5 V

power dissipated by the resistors, P = 3.00 W

the resistance of each resistor, = R

The effective resistance of the three resistors is given by;

R(effective) = R/3

Apply ohms law to determine the current delivered by the source;

V = IR

I = V/R

I = 3V/R

Also, power is calculated as;

P = IV

P = (3V/R) x V

P = 3V²/R

R = 3V² / P

R = (3 x 1.5²) / 3

R = 2.25 Ω

Therefore, the value of resistance of each resistor, R is 2.25 Ω

An expensive vacuum system can achieve a pressure as low as 1.53 ✕ 10−7 N/m2 at 26°C. How many atoms are there in a cubic centimeter at this pressure and temperature?

Answers

Answer:

The  value is  [tex]N = 3.708*10^{7} \ \ atoms[/tex]

Explanation:

From the question we are told that

    The pressure is  [tex]P = 1.53 *10^{-7} \ N/m^2[/tex]

    The  temperature is  [tex]T = 26 + 273 = 299 \ K[/tex]

     The volume is  1 cubic cm = [tex]1 * 10^{-6} m^3[/tex]

Generally according to the ideal gas law we have that

      [tex]PV = NkT[/tex]

here  k is the Boltzmann constant with a value  [tex]k = 1.38 *10^{-23} \ J/K[/tex]

  =>  [tex]N = \frac{PV}{ k T}[/tex]

=>     [tex]N = \frac{ 1.53 *10^{-7} * (1* 10^{-6})}{ 1.38*10^{-23} * 299}[/tex]

=>    [tex]N = 3.708*10^{7} \ \ atoms[/tex]

     

A 500 nm wavelength light illuminates a soap film with an index of refraction 1.33 to make it look bright. If the beam of light is incident normal on the film, what is the minimum thickness of the film

Answers

Answer:

t(min) = 94nm

Explanation:

The wavelength of the light incident is 500 nm.

The refractive index of the film is 1.33.

The minimum thickness of the soap film required for constructive interference.

The thickness of the film for the constructive interference is given by:

2*t= (m + 1/2) λ′

Now, λ′ = λ/μ = 500/1.33 = 376nm

The minimum thickness of the film

′t′ will be at m=0 :

2*t(min) = (0 + 1/2) 376

t(min) = 94nm

A chemist must dilute 55.6 ml of 1.48 M aqueous silver nitrate (AgNO3)solution until the concentration falls to 1.00 M. He'll do this by adding distilled water to the solution until it reaches a certain final volume. Calculate this final volume, in milliliters. Round your answer to 3 significant digits.

Answers

Answer:

82.2 mL

Explanation:

The process of adding water to a solution to make it more dilute is known as dilution. The formula for dilution is;

C1V1=C2V2

Where;

C1= concentration of stock solution

V1= volume of stock solution

C2= concentration of dilute solution

V2= volume of dilute solution

V2= C1V1/C2

V2= 1.48 × 55.6/ 1.0

V2= 82.2 mL

Describe how, using a positively-charged rod and two neutral metal spheres, we canmake one sphere positive without touching it to the rod. You might want to draw adiagram to help you.

Answers

Answer:

se the principle of induction.

place the two metallic spheres together,  now we bring the positively charged bar closer to the first sphere.

The charge that was induced in the sphere is distributed as infirm as possible,

At this time I separate the spheres and move the bar away, by separating the spheres the excess positive

Explanation:

For this exercise we will use that the electric charge is not created, it is not destroyed and charges of the same sign repel.

Let's use the principle of induction. We place the two metallic spheres together, one in front of the other, now we bring the positively charged bar closer to the first sphere.

Here the positive charge of the bar repels the positive charge of the sphere, but as this is mocil it moves as far away as possible, until the negative charge that remains neutralizes the positive charge of the bar.

The charge that was induced in the sphere is distributed as infirm as possible, most of it in the furthest sphere, since the Coulomb force decreases.

At this time I separate the spheres and move the bar away, by separating the spheres the excess positive charge in the last sphere cannot be neutralized, therefore this sphere remains with a positive charge.

Physical properties of a mineral are a result of the arrangement of the atoms in the mineral. Use this fact to explain the following:_________
A. One mineral has a density of 2.7 g/ml while another has a density of 5.1 g/ml
B. The mineral mica cleaves into thin flat sheets while olivine does not show cleavage

Answers

Explanations:

a) The physical properties of a mineral is as a result of the arrangement of the atoms in the minerals. The reason behind one mineral having a density of 2.1 g/ml which is lower than that of another mineral with density of 5.1 g/ml is the packing density of the minerals. Minerals with high density have their atoms more closely packed together, leaving less space between the atoms. This characteristics means that they have more atomic mass per unit volume for a given molecular space, when compared to another mineral with its atoms less closely packed.

b) The property of cleavage is due to the crystalline structure of a mineral species. Cleavage is used to describe the ease with which minerals cleaves. Cleavage is due to a weak bonding strength between the molecules of the mineral, or a due to a greater lattice spacing across the the cleavage plane than in other planes within the crystal. The greater the lattice spacing, the weaker the strength of the bond across a plane.

From these, we can clearly see that the property of cleavage is due to the physical properties of the crystalline structure of the mineral species.

A Cannonball is shot at an angle of 35.0 degrees and is in flight for 11.0 seconds before hitting the ground at the same height from which it was shot.
A. What is the magnitude of the inital velocity?B. What was the maximum height reached by the cannonball?C. How far, horizontally, did it travel?

Answers

Answer:

Explanation:

According to Equations of Projectile motion :

[tex]Time\ of\ Flight = \frac{2vsin(x)}{g}[/tex]

vsin(x) = 11 * 9.8 / 2 = 53.9 m/sec

(A) v (Initial velocity) = 11 * 9.8 / 2 * sin(35) = 94.56 m/sec

[tex]Maximum Height = \frac{(vsinx)^{2} }{2g}[/tex]

(B) Maximum Height = 53.9 * 53.9 / 2 * 9.8 = 142.2 m

[tex]Horizontal Range = vcosx * t[/tex]

(C) Horizontal Range = 94.56 * 0.81 * 11 = 842.52 m

wo 10-cm-diameter charged rings face each other, 25.0 cm apart. Both rings are charged to + 20.0 nC . What is the electric field strength

Answers

Complete question:

Two 10-cm-diameter charged rings face each other, 25.0cm apart. Both rings are charged to +20.0nC. What is the electric field strength at:

a) the midpoint between the two rings?

b) the center of the left ring?

Answer:

a) the electric field strength at the midpoint between the two rings is 0

b) the electric field strength at the center of the left ring is 2712.44 N/C

Explanation:

Given;

distance between the two rings, d = 25 cm = 0.25 m

diameter of each ring, d = 10 cm = 0.1 m

radius of each ring, r = [tex]\frac{0.1}{2} = 0.05 \ m[/tex]

the charge on each ring, q = 20 nC

Electric field strength for a ring with radius r and distance x from the center of the ring is given as;

[tex]E = \frac{kxQ}{(x^2 +r^2)^{3/2}}[/tex]

The electric field strength at the midpoint;

the distance from the left ring to the mid point , x = 0.25 m / 2 = 0.125 m

[tex]E = \frac{kxQ}{(x^2 +r^2)^{3/2}} \\\\E = \frac{8.99*10^{9}*0.125*20*10^{-9}}{(0.125^2 + 0.05^2)^{3/2}} \\\\E = 9210.5 \ N/C[/tex]

[tex]E_{left} = 9210.5 \ N/C[/tex]

The electric field strength due to right ring is equal in magnitude to left ring but opposite in direction;

[tex]E_{right} = -9210.5 \ N/C[/tex]

The electric field strength at the midpoint;

[tex]E_{mid} = E_{left} + E_{right}\\\\E_{mid} = 9210.5 \ N/C - 9210.5 \ N/C\\\\E_{mid} = 0[/tex]

(b)

The distance from the right ring to center of the left ring, x = 0.25 m.

[tex]E = \frac{KxQ}{(x^2 +r^2)^{3/2}} \\\\E = \frac{8.99*10^{9} *0.25*20*10^{-9}}{(0.25^2 + 0.05^2)^{3/2}} \\\\E = 2712.44 \ N/C[/tex]

3. El tambor de una lavadora que gira a 3 000 revoluciones por minuto (rpm) se acelera uniformemente hasta que alcanza las 6 000 rpm, completando un total de 12 revoluciones.

d. Determina la aceleración tangencial, centrípeta y la total en m.s-2 cuando el tambor a alcanzado los 60000 rpm

e. Explica lo que ocurre con la magnitud y dirección de los vectores aceleración tangencial, aceleración centrípeta, aceleración total, aceleración angular, velocidad angular cuando la lavadora ha girado desde 3000 rpm hasta 6000 rpm.

Answers

Answer:

d)    α = 1693.5 rad / s² , a = 392.7 m / s² ,   a_total = α √(R² +1) ,

e)   tan θ = a / α

Explanation:

This is an exercise in linear and angular kinematics.

We initialize reduction of all the magnitudes to the SI system

   w₀ = 3000 rev / min (2π rad / 1rev) (1min / 60s) = 314.16 rad / s

   w = 6000 rev / mi = 628.32 rad / s

   θ = 12 rev = 12 rev (2π rad / 1 rev) = 75.398 rad

d) ask for centripetal, tangential and total acceleration.

Let's start by looking for centripetal acceleration, let's use the formula

          w² = w₀² + 2 α θ

          α = (w²- w₀²) / 2θ

we calculate

           α = (628.32²2 - 314.16²) / 2 75.398

           α = 1693.5 rad / s²

the quantity is linear and angular are related

         

the linear or tangential acceleration is

            a =    α  R

where R is the radius of the drum

            a = 1693.5 R

Unfortunately you do not give the radius of the drum for a complete calculation, but suppose it is a washing machine drum R = 20 cm = 0.20 m

           a = 1693.5 0.20

           a = 392.7 m / s²

the total acceleration is

           a_total = √(a² + α²)

           a_total = √ (α² R² + α²)

           a_total = α √(R² +1)

e) The centripetal acceleration is directed towards the center of the movement is radial and its magnitude is constant

Tangential acceleration is tangency to radius and its value varies proportionally radius

the total accelracicon is the result of the vector sum of the two accelerations and their directions given by trigonometry

            tan θ = a / α

the angular velocity increases linearly when with centripetal acceleration

A 5.2 cm diameter circular loop of wire is in a 1.35 T magnetic field. The loop is removed from the field in 0.29 sec. Assume that the loop is perpendicular to the magnetic field. What is the average induced emf?

Answers

Answer:

9.88 milivolt

Explanation:

Given: diameter d = 5.2 cm

magnetic field B_1 = 1.35 T, final magnetic field B_2 =0 T

t = 0.29 sec.

we know emf =  - dΦ/dt

and flux Φ = BA

A= area

therefore emf ε = -A(B_2-B_1)/Δt

[tex]=-\pi(d/2)^2\frac{B_2-B_1}{\Delta t} \\=-\pi(0.052/2)^2\frac{0-1.35}{0.29} \\=98.8\times10^4\\=9.88 mV[/tex]

The equivalent resistance of two resistors connected in series is always greater than the equivalent resistance of the same two resistors connected in parallel. True False

Answers

Answer:

True

Explanation:

Because the resistors in series is the sum of the two resistors given as

R= R1+R2

While that of resistors in parallel is the sum of the reciprocal of the resistance given as

1/R = 1/ R1+ 1/R2

So that of series connection will be greater

A satellite in geostationary orbit is used to transmit data via electromagnetic radiation. The satellite is at a height of 35,000 km above the surface of the earth, and we assume it has an isotropic power output of 1.0 kW (although, in practice, satellite antennas transmit signals that are less powerful but more directional).

Required:
a. Reception devices pick up the variation in the electric field vector of the electromagnetic wave sent out by the satellite. Given the satellite specifications listed in the problem introduction, what is the amplitude E0 of the electric field vector of the satellite broadcast as measured at the surface of the earth? Use ϵ0=8.85×10^−12C/(V⋅m) for the permittivity of space and c=3.00×10^8m/s for the speed of light.

b. Imagine that the satellite described in the problem introduction is used to transmit television signals. You have a satellite TV reciever consisting of a circular dish of radius R which focuses the electromagnetic energy incident from the satellite onto a receiver which has a surface area of 5 cm^2. How large does the radius R of the dish have to be to achieve an electric field vector amplitude of 0.1 mV/m at the receiver?

Answers

Answer:

1. 6.99x 10^-6V/m

2. 18m

Explanation:

See attached file

An electron moves on a circular orbit in a uniform magnetic field of 7.83×10-4 T. The kinetic energy of the electron is 55.3 eV. What is the diameter of the orbit?

Answers

Answer:

3.9E-8

Explanation:

We know that

Mv²/r = Bqv

So

r= mv/Bq

But E is 1/2mv² which is 5.53eV

m²v² =2m x 5.53eV

mv = √( 2 x 9.1E-31)

So

r= √( 2 x9.1E-31 x 5.53)/ 7.83x10^-4 x1.6E-19

= 3.9x10-8cm

Explanation:

Water is pumped with a 120 kPa compressor entering the lower pipe (1) and flows upward at a speed of 1 m/s. Acceleration due to gravity is 10 m/s and water density is1000 kg/m-3. What is the water pressure on the upper pipe (II).

Answers

Answer:

The water pressure on the upper pipe is 92.5 kPa.

Explanation:

Given that,

Pressure in lower pipe= 120 kPa

Speed of water in lower pipe= 1 m/s

Acceleration due to gravity = 10 m/s²

Density of water = 1000 kg/m³

Radius of lower pipe = 12 m

Radius of uppes pipe = 6 m

Height of upper pipe = 2 m

We need to calculate the velocity in upper pipe

Using continuity equation

[tex]A_{1}v_{1}=A_{2}v_{1}[/tex]

[tex]\pi r_{1}^2\times v_{1}=\pi r_{2}^2\times v_{2}[/tex]

[tex]v_{2}=\dfrac{r_{1}^2\times v_{1}}{r_{2}^2}[/tex]

Put the value into the formula

[tex]v_{2}=\dfrac{12^2\times1}{6^2}[/tex]

[tex]v_{2}=4\ m/s[/tex]

We need to calculate the water pressure on the upper pipe

Using bernoulli equation

[tex]P_{1}+\dfrac{1}{2}\rho v_{1}^2+\rho gh_{1}=P_{2}+\dfrac{1}{2}\rho v_{2}^2+\rho gh_{2}[/tex]

Put the value into the formula

[tex]120\times10^{3}+\dfrac{1}{2}\times1000\times1^2+1000\times10\times0=P_{2}+\dfrac{1}{2}\times1000\times(4)^2+1000\times10\times2[/tex]

[tex]120500=P_{2}+28000[/tex]

[tex]P_{2}=120500-28000[/tex]

[tex]P_{2}=92500\ Pa[/tex]

[tex]P_{2}=92.5\ kPa[/tex]

Hence, The water pressure on the upper pipe is 92.5 kPa.

Find the average magnitude of the induced emf if the change in shape occurs in 0.125 ss and the local 0.504-TT magnetic field is perpendicular to the plane of the loop.

Answers

Complete Question

An emf is induced in a conducting loop of wire 1.12m long as its shape is.

changed from square to circular. Find the average magnitude of the induced emf if the change in shape occurs in 0.125 ss and the local 0.504-TT magnetic field is perpendicular to the plane of the loop.

Answer:

The induced emf is  [tex]\epsilon = 0.0863 \ V[/tex]

Explanation:

From the question we are told that

      The  time taken is  [tex]\Delta t = 0.125 \ s[/tex]

       The magnitude of the magnetic field is  B =  0.504 T

        The length of the loop wire is  [tex]l = 1.12 \ m[/tex]

Generally the circumference of the wire when in circular form is  

          [tex]C = 2 \pi r[/tex]

=>        [tex]l = 2 \pi r[/tex]

=>         [tex]r =[/tex][tex]\frac{l}{2 \pi}[/tex]

=>          [tex]r =[/tex][tex]\frac{1.12}{2 * 3.142}[/tex]

=>        [tex]r =[/tex][tex]0.1782 \ m[/tex]

Now the area of the wire as a circle is

           [tex]A = \pi r^2[/tex]

    =>     [tex]A = 3.142 * (0.1782)^2[/tex]      

     =>    [tex]A = 0.0998 \ m^2[/tex]

The  length of one side of the square is

         [tex]b = \frac{l}{4}[/tex]

         [tex]b = \frac{1.12}{4}[/tex]

         [tex]b = 0.28 \ m[/tex]

Now the area of the wire as a square is

          [tex]A_s = b^2[/tex]

=>          [tex]A_s =(0.28 )^2[/tex]

             [tex]A_s = 0.0784 \ m^2[/tex]

Generally the induced emf is mathematically represented as

        [tex]\epsilon = \frac{B * [A - A_s ]}{\Delta t }[/tex]

=>      [tex]\epsilon = \frac{0.504 * [0.0998 - 0.0784 ]}{0.125 }[/tex]

=>      [tex]\epsilon = 0.0863 \ V[/tex]

   

A high school physics student claims her muscle car can achieve a constant acceleration of 10 ft/s/s. Her friend develops an accelerometer to confirm the feat. The accelerometer consists of a 1 ft long rod (mass=4 kg) with one end attached to the ceiling of the car, but free to rotate. During acceleration, the rod rotates. What will be the angle of rotation of the rod during this acceleration? Assume the road is flat and straight.

Answers

Answer: Ф = 17.2657 ≈ 17°

Explanation:

we simply apply ET =0 about the ending of the rod

so In.g.L/2sinФ - In.a.L/2cosФ = 0

g.sinФ - a.cosФ = 0

g.sinФ = a.cosФ

∴ tanФ = a/g

Ф =  tan⁻¹ a / g

Ф = tan⁻¹ ( 10 / 32.17405)

Ф = tan⁻¹ 0.31080948777

Ф = 17.2657 ≈ 17°

Therefore the angle of rotation of the rod during this acceleration is 17.2657 ≈ 17°

Two instruments produce a beat frequency of 5 Hz. If one has a frequency of 264 Hz, what could be the frequency of the other instrument

Answers

Answer:

259 Hz or 269 Hz

Explanation:

Beat: This is the phenomenon obtained when two notes of nearly equal frequency are sounded together. The S.I unit of beat is Hertz (Hz).

From the question,

Beat = f₂-f₁................ Equation 1

Note: The frequency of the other instrument is either f₁ or f₂.

If the unknown instrument's frequency is f₁,

Then,

f₁ = f₂-beat............ equation 2

Given: f₂ = 264 Hz, Beat = 5 Hz

Substitute into equation 2

f₁ = 264-5

f₁ = 259 Hz.

But if the unknown frequency is f₂,

Then,

f₂ = f₁+Beat................. Equation 3

f₂ = 264+5

f₂ = 269 Hz.

Hence the beat could be 259 Hz or 269 Hz

This problem explores the behavior of charge on conductors. We take as an example a long conducting rod suspended by insulating strings. Assume that the rod is initially electrically neutral. For convenience we will refer to the left end of the rod as end A, and the right end of the rod as end B. In the answer options for this problem, "strongly attracted/repelled" means "attracted/repelled with a force of magnitude similar to that which would exist between two charged balls.A. A small metal ball is given a negative charge, then brought near (i.e., within about 1/10 the length of the rod) to end A of the rod. What happens to end A of the rod when the ball approaches it closely this first time?
What happens to end A of the rod when the ball approaches it closely this first time?a. It is strongly repelled.b. It is strongly attracted.c. It is weakly attracted.d. It is weakly repelled.e. It is neither attracted nor repelled.

Answers

Answer:

e. It is neither attracted nor repelled.

Explanation:

Electrostatic attraction or repulsion occurs between two or more charged particles or conductors. In this case, if the negatively charged ball is brought close to the neutral end A of the rod, there would be no attraction or repulsion between the rod end A and the negatively charged ball. This is because a charged particle or conductor has no attraction or repulsion to a neutral particle or conductor.

What is the maximum speed (in units of m/s) with which a car can round a
flat horizontal curve of radius (r=60 m), if the coefficient of static friction between tires and
road is (0.4)?
A) 5
B) 15.5
€) 240
D) 25.1​

Answers

Answer:

B)  15.5 m/s

Explanation:

r = 60m

μs = 0.4

using the formula max V = √r*g*μs (flat roadway)

v = sqrt(60 * 10 * 0.4)

v = 15.5 m/s

A diver shines an underwater searchlight at the surface of a pond (n = 1.33). At what angle (relative to the surface) will the light be totally reflected?

Answers

Answer:

41.2°

Explanation:

Total internal reflection is the reflection of the incident ray at the interface between two media in which one of the media has a lower refractive index than the other. It occurs when the angle of incidence in the denser medium exceeds the critical angle.

The critical angle is the angle of incidence in the denser medium when the angle of incidence in the less dense medium is 90°.

Since

n= 1/sin C

C= sin^-(1/n)

C= sin^-(1/1.33)

C= 48.8°

Hence angle of incidence= 90-48.8 = 41.2°

What is the maximum wavelength of incident light that can produce photoelectrons from silver? The work function for silver is Φ=2.93 eV.

Answers

Answer:

The maximum wavelength of incident light that can produce photoelectrons from silver is 423.5 nm.

Explanation:

Given;

work function of silver, Φ = 2.93 eV = 2.93 x 1.602 x 10⁻¹⁹ J = 4.6939 x 10⁻¹⁹ J

Apply Einstein Photo electric effect;

E = K.E + Ф

Where;

E is the energy of the incident light

K.E is the kinetic of electron

Ф is the work function of silver surface

For the incident light to have maximum wavelength, the kinetic energy of the electron will be zero.

E = Ф

hf = Ф

[tex]h\frac{c}{\lambda} = \phi[/tex]

where;

c is speed of light = 3 x 10⁸ m/s

h is Planck's constant, = 6.626 x 10⁻³⁴ J/s

λ is the wavelength of the incident light

[tex]\lambda = \frac{hc}{\phi}\\\\\lambda =\frac{6.626*10^{-34} *3*10^8}{4.6939*10^{-19}} \\\\\lambda = 4.235 *10^{-7} \ m\\\\\lambda = 423.5 *10^{-9} \ m\\\\\lambda = 423.5 \ nm[/tex]

Therefore, the maximum wavelength of incident light that can produce photoelectrons from silver is 423.5 nm.

Two ice skaters, Paula and Ricardo, initially at rest, push off from each other. Ricardo weighs more than Paula.
A. Which skater, if either, has the greater momentum after the push-off? Explain.
B. Which skater, if either, has the greater speed after the push-off? Explain.

Answers

Answer:

the two ice skater have the same momentum but the are in different directions.

Paula will have a greater speed than Ricardo after the push-off.

Explanation:

Given that:

Two ice skaters, Paula and Ricardo, initially at rest, push off from each other. Ricardo weighs more than Paula.

A. Which skater, if either, has the greater momentum after the push-off? Explain.

The law of conservation of can be applied here in order to determine the skater that possess a greater momentum after the push -off

The law of conservation of momentum states that the total momentum of two  or more objects acting upon one another will not change, provided there are no external forces acting on them.

So if two objects in motion collide, their total momentum before the collision will be the same as the total momentum after the collision.

Momentum is the product of mass and velocity.

SO, from the information given:

Let represent the mass of Paula with [tex]m_{Pa}[/tex] and its initial velocity with [tex]u_{Pa}[/tex]

Let represent the mass of Ricardo with [tex]m_{Ri}[/tex] and its initial velocity with [tex]u_{Ri}[/tex]

At rest ;

their velocities will be zero, i.e

[tex]u_{Pa}[/tex] = [tex]u_{Ri}[/tex] = 0

The initial momentum for this process can be represented as :

[tex]m_{Pa}[/tex][tex]u_{Pa}[/tex] +  [tex]m_{Ri}[/tex][tex]u_{Ri}[/tex] = 0

after push off from each other then their final velocity will be [tex]v_{Pa}[/tex] and [tex]v_{Ri}[/tex]

The we can say their final momentum is:

[tex]m_{Pa}[/tex][tex]v_{Pa}[/tex] +   [tex]m_{Ri}[/tex][tex]v_{Ri}[/tex] = 0

Using the law of conservation of momentum as states earlier.

Initial momentum = final momentum = 0

[tex]m_{Pa}[/tex][tex]u_{Pa}[/tex] +  [tex]m_{Ri}[/tex][tex]u_{Ri}[/tex] =  [tex]m_{Pa}[/tex][tex]v_{Pa}[/tex] +   [tex]m_{Ri}[/tex][tex]v_{Ri}[/tex]

Since the initial velocities are stating at rest then ; u = 0

[tex]m_{Pa}[/tex](0) + [tex]m_{Pa}[/tex](0) = [tex]m_{Pa}[/tex][tex]v_{Pa}[/tex] +   [tex]m_{Ri}[/tex][tex]v_{Ri}[/tex]

[tex]m_{Pa}[/tex][tex]v_{Pa}[/tex] +   [tex]m_{Ri}[/tex][tex]v_{Ri}[/tex]  = 0

[tex]m_{Pa}[/tex][tex]v_{Pa}[/tex] = - [tex]m_{Ri}[/tex][tex]v_{Ri}[/tex]

Hence, we can conclude that the two ice skater have the same momentum but the are in different directions.

 B. Which skater, if either, has the greater speed after the push-off? Explain.

Given that Ricardo weighs more than Paula

So [tex]m_{Ri} > m_{Pa}[/tex] ;

Then [tex]\mathsf{\dfrac{{m_{Ri}}}{m_{Pa} }= 1}[/tex]

The magnitude of their momentum which is a product of mass and velocity can now be expressed as:

[tex]m_{Pa}[/tex][tex]v_{Pa}[/tex] =  [tex]m_{Ri}[/tex][tex]v_{Ri}[/tex]

The ratio is

[tex]\dfrac{v_{Pa}}{v_{Ri}} =\dfrac{m_{Ri}}{m_{Pa}} = 1[/tex]

[tex]v_{Pa} >v_{Ri}[/tex]

Therefore, Paula will have a greater speed than Ricardo after the push-off.

(A) Both the skaters have the same magnitude of momentum.

(B) Paula has greater speed after push-off.

Conservation of momentum:

Given that two skaters Paula and Ricardo are initially at rest.

Ricardo weighs more than Paula.

Let us assume that the mass of Ricardo is M, and the mass of Paula is m.

Let their final velocities be V and v respectively.

(A) Initially, both are at rest.

So the initial momentum of Paula and Ricardo is zero.

According to the law of conservation of momentum, the final momentum of the system must be equal to the initial momentum of the system.

Initial momentum = final momentum

0 = MV + mv

MV = -mv

So, both of them have the same magnitude of momentum, but in opposite directions.

(B) If we compare the magnitude of the momentum of Paula and Ricardo, then:

MV = mv

M/m = v/V

Now, we know that M>m

so, M/m > 1

therefore:

v/V > 1

v > V

So, Paula has greater speed.

Learn more about conservation of momentum:

https://brainly.com/question/2141713?referrer=searchResults

if a 1-m diameter sewer pipe is flowing at a depth of 0.4 m and has a flow rate of 0.15 m^3/s, what will be the flow rate when the pipe flows full?

Answers

Answer:

0.35 m³/s

Explanation:

When the pipe's depth is 0.4 m, the area of the circular segment is:

A = ½ R² (θ − sin θ)

The depth of the water is:

h = R (1 − cos(θ/2))

Solving for θ:

0.4 = 0.5 (1 − cos(θ/2))

0.8 = 1 − cos(θ/2)

cos(θ/2) = 0.2

θ/2 = acos(0.2)

θ = 2 acos(0.2)

θ ≈ 2.74 rad

The area is therefore:

A = ½ (0.5 m)² (2.74 − sin 2.74)

A = 0.338 m²

The cross-sectional area when the pipe is full is:

A = π (0.5 m)²

A = 0.785 m²

The flow velocity is constant:

v = v

Q / A = Q / A

(0.15 m³/s) / (0.338 m²) = Q / (0.785 m²)

Q = 0.35 m³/s

An LR circuit consists of a 35-mH inductor, ac resistance of 12 ohms, an 18-V battery, and a switch. What is the current 5.0 ms after the switch is closed

Answers

Answer:

 I = 1.23 A

Explanation:

In an RL circuit current passing is described by

           I = E / R (1 - [tex]e^{-Rt/L}[/tex])

Let's reduce the magnitudes to the SI system

        L = 35 mH = 35 10⁻³ H

        t = 5.0 ms = 5.0 10⁻³ s

let's calculate

         I = 18/12 (1 - [tex]e^{-12 .. 5 {10}^{-3}/35 .. {10}^{-3} }[/tex]e (- 5 10-3 12/35 10-3))

         I = 1.5 (1- [tex]e^{-1.715}[/tex])

         I = 1.23 A

A ceiling fan is spinning at 45 revolutions per minute when it is switched to a higher speed. It accelerates uniformly, and 2.0 seconds later it is spinning at 110 revolutions per minute. Through how many radians did it rotate during the transition of speeds

Answers

Answer:

θ = 16.2 rad

Explanation:

First we find the angular acceleration by using first equation of motion in angular form:

ωf = ωi + αt

where,

ωf =final angular speed = (110 rev/min)(2π rad/1 rev)(1 min/60 s) = 11.5 rad/s

ωi =initial angular speed = (45 rev/min)(2π rad/1 rev)(1 min/60 s) = 4.7 rad/s

α = angular acceleration = ?

t = time = 2 s

Therefore,

11.5 rad/s = 4.7 rad/s + α(2 s)

α = (6.8 rad/s)/(2 s)

α = 3.4 rad/s²

Now, we use 2nd equation of motion:

θ = ωi t + (1/2)αt²

where,

θ = rotation = ?

Therefore,

θ = (4.7 rad/s)(2 s) + (1/2)(3.4 rad/s²)(2 s)²

θ = 9.4 rad + 6.8 rad

θ = 16.2 rad

What would happen in a State if its citizens lack relevant knowledge, skills
and positive attitude?​

Answers

Answer:

If the older generation is lacking, the younger generation would likely have knowledge, skill, or a positive attitude in some combination, but it is relative to the culture.

The simple reason is the desirability for genetic variation using recessive genes.

In other words, if the older generation lacks something, it tends to be something they don’t need, but something that will look good on young people. But mostly relative to the culture and education system.

Hope this helps

Two hoops, staring from rest, roll down identical incline planes. The work done by nonconservative forces is zero. The hoops have the same mass, but the larger hoop has twice the radius. Which hoop will have the greater total kinetic energy at the bottom

Answers

Answer:

They both have the same total K.E at the bottom

Explanation:

This Is because If assuming no work is done by non conservative forces, total mechanical energy must be conserved

So

K1 + U1 = K2 + U2

But If both hoops start from rest, and and at the bottom of the incline the level for gravitational potential energy is zero for reference

thus

K1 = 0 , U2 = 0

ΔK = ΔU = m g. h

But if the two inclines have the same height, and both hoops have the same mass m,

So difference in kinetic energy, must be the same for both hoops.

In the lab , you have an electric field with a strength of 1,860 N/C. If the force on a particle with an unknown charge is 0.02796 N, what is the value of the charge on this particle.

Answers

Answer:

The charge is  [tex]q = 1.50 *10^{-5} \ C[/tex]

Explanation:

From the question we are told that

   The electric field strength is  [tex]E = 1860 \ N/C[/tex]

    The force is  [tex]F = 0.02796 \ N[/tex]

Generally the charge on this particle is mathematically represented as

     [tex]q = \frac{F}{E}[/tex]

=>   [tex]q = \frac{0.02796}{ 1860}[/tex]

=>   [tex]q = 1.50 *10^{-5} \ C[/tex]

Nine tree lights are connected inparallel across 120-V potential difference. The cord to the wall socket carries a current of 0.43 A. Required:a. Detrmine the resistance of one of the bulbs.b. What would the current be if the bulbs were connected in series?

Answers

Answer:

a)3000ohm

b)4.44mA

Explanation:

a) we were given a Nine tree lights connected inparallel across 120-V potential difference, since the resistor are in parallel we use the expresion below

1/R(total)= 1/R₁ + 1/R₂ + 1/R₃ + 1/R₃ +.... 1/R₉

But according to ohm'law which can be expressed below

V=IR

R=V/I

R(total)= 120/0.36

= 333.33ohm

1/R(total)= 1/R₁ + 1/R₂ + 1/R₃ + 1/R₃ +.... 1/R₉

R₁=R₂ =R₃ =R₄= R₅=R₆=R₇=R₈=R₉

1/R(total)=9/R

1/333.33= 9/R

R= 3000ohm

Therefore, the resistance is 3000ohm

b)the bulbs were connected in series here, then for series connection we use below expression

R₁=R₂ =R₃ =R₄= R₅=R₆=R₇=R₈=R₉

R(total)=9R

= 9*3000

=27000ohm

I=VR

I=V/R

I= 120/27000

= 4.44*10⁻³A

4.44mA

Therefore, the current is 4.4mA

A resistor and a capacitor are connected in series to an ideal battery of constant terminal voltage. At the moment contact is made with the battery, the voltage across the resistor is

Answers

Answer:

At the moment contact is made with the battery, the voltage across the resistor is equal to the batteries terminal voltage

Explanation;

Because at series connection the battery and resistor have equal voltage

Other Questions
PLS ANYONE IT'S URGENT Explain eubacteria ? How many multiples of 4, that are smaller than 1,000, do not contain any of the digits 6, 7, 8, 9 or 0? I really need a answer. Name the quadrants in which of the following points (3, 0) (-9,-3) lie. can u help me with this problem PLEASE HELP ASAP YOU WILL GET BRAINLIST!!!!!! 20 POINTS!!!!!!!!!! What is the South American word for mountains? sierras cordillera cotopaxi altiplanos A battery establishes a voltage V on a parallel-plate capacitor. After the battery is disconnected, the distance between the plates is doubled without loss of charge. Accordingly:_____.a. stay same b. increases c. decreases d. the capacitance decreases and the voltage between the plates increases. Assume you have a margin account with a 50% initial margin. You purchase 100 shares of stock at $80 per share. The price increases to $100 per share. What is the net value of your investment (margin) now What is a major problem in Paraguay? A space rocket accelerates uniformly from rest to 160ms^-1 upwards in 4.0s, then travels with a constant speed of 160ms^-1 for the next 5.0s.What is the initial acceleration of the rocket? The amortization of bond premium on long-term debt should be presented in a statement of cash flows (using the indirect method for operating activities) as a(n) The master budget of Sheffield Corp. shows that the planned activity level for next year is expected to be 50000 machine hours. At this level of activity, the following manufacturing overhead costs are expected: Indirect labor$730000 Machine supplies200000 Indirect materials220000 Depreciation on factory building120000 Total manufacturing overhead $1270000 A flexible budget for a level of activity of 60000 machine hours would show total manufacturing overhead costs of Applying ACh to the small intestine will cause a smooth muscle ______, which is through activation of ______ receptors. Think of two methods used to improve productivity in business. Discuss your reasons for choosing these methods A developer buys the last five vacant lots in a subdivision and constructs a large, expensive home on each lot. The homes sell for what are record-setting high prices for the area. The owners of the older, lesser-valued houses in the neighborhood may find that the values of their homes are affected by what principle Which two examples would be categorized as a tragicomedy? a dramatic work with a happy ending a dramatic work with a tragic ending a tragedy with humorous qualities a tragedy with a dramatic ending a comedy with humorous qualities Consider a triangle ABC like the one below. Suppose that b=27, c=66, and B=130. (The figure is not drawn to scale.) Solve the triangle.Carry your intermediate computations to at least four decimal places, and round your answers to the nearest tenth.If no such triangle exists, enter "No solution." If there is more than one solution, use the button labeled "or". Nadiya determines that there are no fractions equivalent to StartFraction 2 Over 10 EndFraction with a denominator greater than 10, but less than 20, that have a whole number numerator and denominator. Is Nadiya correct?Yes, Nadiya is correct. By multiplying the numerator and denominator by 2, the first fraction equivalent to StartFraction 2 Over 10 EndFraction is StartFraction 4 Over 20 EndFraction.Yes, Nadiya is correct. By multiplying the whole fraction by any whole number, each equivalent fraction will continue to have a denominator of 10.No, Nadiya is incorrect. She could multiply both the numerator and denominator of the unit fraction equivalent to StartFraction 2 Over 10 EndFraction by 3 and arrive at the equivalent fraction StartFraction 3 Over 15 EndFraction.No, Nadiya is incorrect. She could add any number between 1 and 8 to the numerator and denominator and arrive at an equivalent fraction with a denominator greater than 10 but less than 20. Suppose Earths axis was perpendicular to the plane of Earths orbit around the Sun. How would the climate at the place you live differ from the climate today? How would it change if Earths orbit became much more elliptical? A low-noise transistor for use in computing products is being developed. It is claimed that the mean noise level will be below the 2.5-dB level of products currently in use. It is believed that the noise level is approximately normal with a standard deviation of .8. find 95% CI The nurse is teaching a nursing student about infection. Which is an example of a reservoir of infection?