A fixed mass of saturated water vapor at 400 kpa is isothermally cooled until it is a saturated liquid. Calculate the amount of heat rejected during this process in kJ/kg.

Answer:

A) Flow depth = 2.46 m, Froude number after jump = 0.464

B) head loss = 0.572 m

C) dissipation ratio = 0.173

Explanation:

Given data :

Velocity before jump ( v1 ) = 7 m/s

flow depth before jump ( y1 ) = 0.8 m

g = 9.81 m/s

Esi = 3.3 m ( calculated )

attached below is a detailed solution of the problem

Answer:

  Put a 10.0-ohm resistor in the circuit. Measure the current in the circuit. Replace the 10.0-ohm resistor with a 20.0-ohm resistor. Measure the new current. Continue replacing the resistor with a different resistor of known resistance. Measure the current for each resistor. Record all data.

Explanation:

The only design that has resistance varying with everything else remaining the same is the first design. That would be what you'd want to do if you're exploring the effect of resistance on current.

Answer: the half-angle "alpha" of the Mach cone = 30⁰

Explanation:

To calculate the  half-angle "alpha" of the Mach cone.

we say ;

Sin∝ = 1 / Ma

given that Ma = 2

now we substitute

Sin∝ = 1 / 2

Sin∝ = 0.5

∝ = Sin⁻¹ 0.5

∝ = 30⁰

Therefore, the half-angle "alpha" of the Mach cone is 30⁰

Answer:

C) a winding connected in series with the armature.

Explanation:

In a series motor, an electromagnet is used as a stator to generate its magnetic field. The field coil of this stator are connected through a commutator in series with the rotor windings. This stator which is the armature windings will conduct AC even on a DC machine, due to the  periodically reverses current direction (commutation) or due to electronic commutation (as in brushless DC motors).

Answer:

  resistance

Explanation:

A strain gauge changes resistance with applied strain.

Answer:

Both Technician A and technician B are correct.

Explanation: A transistor must have a P-N junction as that is where the positive and negative charges are connected.

A transistor also can be described as a semiconductor which acts as a switch and can be used to amplify currents. Transistors are very key and vital to electronic devices especially the mobile phones in recent times, it helps to ensure that electronic systems perform optimally.

The charges in the P-N junction is controlled by the availability of Positive and negative electrons.

Answer:both

Explanation:

Answer: A prototype

Explanation:

The scale model that proves the initial concept is called a domain model.

A copy or depiction of something where all parts have the same dimensions as the original. A scale model is an image or copy of an object that is either larger or smaller than the object being represented's actual size.

A domain model is a type of conceptual model that is used to depict the structural elements and conceptual constraints within a domain of interest.

A domain model will include all of the entities, their attributes, and relationships, as well as the constraints that govern the conceptual integrity of the structural model elements that comprise that problem domain.

Therefore, a domain model is the scale model that proves the initial concept.

To learn more about the scale model, refer to the below link:

https://brainly.com/question/14341149

#SPJ2

Answer:

the torque required to RAISE the load is Tr = 18.09 Nm

the torque required to LOWER the load is Tl = 10.069 ≈ 10.07 Nm

the Overall Efficiency e = 0.2199 ≈ 0.22

Explanation:

Given that; F = 5 kN, p = 5mm, d = 35mm

Dm = d - p/2

Dm = 35 - ( 5/2) = 35 - 2.5

DM = 32.5mm

So the torque required to RAISE the load is

Tr = ( 5 × 32.5)/2 [(5 + (π × 0.09 × 32.5)) / ( (π × 32.5) - ( 0.09 × 5))] + [( 5 × 0.06 × 45)/2]

Tr = 81.25 × (14.1892 / 101.6518) + 6.75

Tr = 11.3414 + 6.75

Tr = 18.09 Nm

the torque required to LOWER the load is

Tl =  ( 5 × 32.5)/2 [(π × 0.09 × 32.5) - 5) / ( (π × 32.5) + ( 0.09 × 5))] + [( 5 × 0.06 × 45)/2]

Tl = 81.25 × 4.1892 / 102.5518 + 6.75

Tl = 3.3190 + 6.75

Tl = 10.069 ≈ 10.07 Nm

So since torque required to LOWER the load is positive

that is, the thread is self locking

Therefore the efficiency is

e = ( 5 × 5 ) / ( 2π × 18.09 )

e = 25 / 113.6628

e = 0.2199 ≈ 0.22

Answer:

A)  ( N ) = 1.54

B)  N ( Goodman ) = 1.133,  N ( Morrow) = 1.35

Explanation:

width of steel bar = 25-mm

thickness of steel bar = 10-mm

diameter = 6-mm

load on plate = between 12 kN AND 28 kN

notch sensitivity = 0.83

A ) Fatigue factor of safety based on yielding criteria

= δa + δm = [tex]\frac{Syt}{n}[/tex]   =  91.03 + 227.58 = 490 / N

therefore Fatigue number of safety ( N ) = 1.54

δa (amplitude stress ) = kf ( Fa/A) = 2.162 * ( 8*10^3 / 190 ) = 91.03 MPa

A = area of steel bar = 190 mm^2 , Fa = amplitude load = 8 KN , kf = 2.162

δm (mean stress ) = kf ( Fm/A ) = (2.162 * 20*10^3 )/ 190 = 227.58 MPa

Fm = mean load  = 20 *10^3

B) Fatigue factor of safety based on Goodman and Morrow criteria

δa / Se + δm / Sut = 1 / N

= 91.03 / 183.15 + 227.58 / 590 = 1 /N

Hence N = 1.133 ( based on Goodman criteria )

note : Se = endurance limit (calculated) = 183.15 , Sut = 590

applying Morrow criteria

N =   1 / ( δa/Se) + (δm/ δf )

   = 1 / ( 91.03 / 183.15 ) + (227.58 / 935 )  

   = 1.35

Answer:

Explanation:

In a particular application involving airflow over a heated surface, the boundary layer temperature distribution, T(y), may be approximated as:

[ T(y) - Ts / T∞ - Ts ] = 1 - e^( -Pr (U∞y / v) )

where y is the distance normal to the surface and the Prandtl number, Pr = Cpu/k = 0.7, is a dimensionless fluid property. a.) If T∞ = 380 K, Ts = 320 K, and U∞/v = 3600 m-1, what is the surface heat flux? Is this into or out of the wall? (~-5000 W/m2 , ?). b.) Plot the temperature distribution for y = 0 to y = 0.002 m. Set the axes ranges from 380 to 320 for temperature and from 0 to 0.002 m for y. Be sure to evaluate properties at the film temperature.

Answer:

V2= 1666.6 volts

Explanation:

Given data

primary turns N1= 100 turns

secondary turns N2= 1500 turns

primary voltage V1= 110 volts

secondary voltage V2= ?

We can solve for the output voltage using the turns ration sated below

  Turns Ratio = N1 / N2 = V1 / V2

Substituting our given data into the expression we have

100/1500= 110/V2

Making V2 subject of formula we have

V2= 110/(100/1500)=  1666.6 volts

V2= 1666.6 volts

Hence the secondary voltage is 1666.6 volts

Answer:

minimum current level required =  8975.95 amperes

Explanation:

Given data:

diameter = 5.5 mm

length = 5.0 mm

T = 0.3

unit melting energy = 9.5 j/mm^3

electrical resistance = 140 micro ohms

thickness of each of the two sheets = 3.5mm

Determine the minimum current level required

first we calculate the volume of the weld nugget

v = [tex]\frac{\pi }{4} * D^2 * l[/tex] = [tex]\frac{\pi }{4} * 5.5^2 * 5[/tex] = 118.73 mm^3

next calculate the required melting energy

= volume of weld nugget * unit melting energy

= 118.73 * 9.5 = 1127.94 joules

next find the actual required electric energy

= required melting energy / efficiency

= 1127 .94 / ( 1/3 )  = 3383.84 J

TO DETERMINE THE CURRENT LEVEL REQUIRED  use the relation below

electrical energy =  I^2 * R * T

3383.84 / R*T = I^2

3383.84 / (( 140 * 10^-6 ) * 0.3 ) = I^2

therefore  8975.95 = I ( current )

Answer: a = change in w =0.00656

b = q = 5.1kj/kg

Explanation:

Find explanation in the attached file

The amount of steam added to the air  a = change in w =0.00656 b = q = 5.1kj/kg

The digital game retail and distribution service Steam is provided by Valve. In order to allow Valve to automatically update its games, it was first released as a software client in September 2003. In late 2005, it was expanded to include the distribution and sale of games from other publishers.

a) We can use the absolute humidity we and wg to determine the amount

of moisture added Aw.

Aww3-W2

Aw= 0.01291 -0.00635

Aw= 0.00656

b) To determine the heat transfer q we will need the enthalpies h and h2.

kJ

kg 9 = 36.2

kJ  kg

31.1

q=5.1

kJ

kg

RESULT

Do = 0.00656

kJ

kg

9 = 5.1

Therefore, The amount of steam added to the air  a = change in w =0.00656 b = q = 5.1kj/kg

Learn more about steam here:

https://brainly.com/question/15447025

#SPJ2

Answer:

a. 115

b. 135

c. 220

d. 185

Explanation:

Spheriodite is microscopic constituents in some steels which is composed of spherically shaped cementide particle. It is most ductile and softest type of steel. Pearlite is two phased lamellar compose of alternating layer of ferrite and cementite. It is hard and strong but not tough. It is applied on cutting tools like chopper, blades and knives.

Answer: hello attached below is the diagram which is part of your question

Total entropy change  = entropy change in cold reservoir + entropy change in hot reservoir = -0.166 + 0.083 = -0.0837 kj/k  it violates Clausius increase of entropy which is Sgen > 0

Explanation:

Clausius statement states that it is impossible to transfer heat energy from a cooler body to a hotter body in a cycle or region without any other external factors affecting it .  

applying the increase in entropy principle to prove this

temp of cold reservoir (t hot)= 600 k

temp of hot reservoir(t cold) = 1220 k

energy (q) = 100 kj

total entropy change  = entropy change in cold reservoir + entropy change in hot reservoir = -0.166 + 0.083 = -0.0837 kj/k

entropy change in cold reservoir = Q/t cold = 100 / 600 = -0.166 kj/k

entropy change in hot reservoir = Q / t hot = 100 / 1220 = 0.083 kj/k

hence it violates  Clausius inequality of increase of entropy principle which is states that generated entropy has to be > 0

Answer:

Explanation:

The only vertical force that can be applied at joint D is that of link CD. Since joint D is stationary, there must be no vertical force. Hence the force in link CD must be zero, as must the force in link DE.

At joint E, the only horizontal force is that applied by link EF, so it, too, must be zero.

Then link CE has 15 N tension.

The downward force in CE must be balanced by an upward force in CF. Of that force, only 1/√2 of it will be vertical, so the force in CF is a compression of 15√2 N.

In order for the horizontal forces at C to be balanced the 15 N horizontal compression in CF must be balanced by a 15 N tension in BC.

At joint F, the 15 N horizontal compression in CF must be balanced by a 15 N compression in FA. CF contributes a downward force of 15 N at joint F. Together with the external load of 10 N, the total downward force at F is 25 N. Then the tension in BF must be 25 N to balance that.

At joint B, the 25 N downward vertical force in BF must be balanced by the vertical component of the compressive force in AB. That component is 2/√5 of the total force in AB, which must be a compression of 25√5/2 N.

The horizontal forces at joint B include the 15 N tension in BC and the 25/2 N compression in AB. These are balanced by a (25/2+15) N = 55/2 N tension in BG.

In summary, the link forces are ...

_____

Note that the forces at the pins of G and A are in accordance with those that give a net torque about those point of 0, serving as a check on the above calculations.

Answer:

Electrical conductivity or specific conductance is the reciprocal of electrical resistivity. It represents a material's ability to conduct electric current. It is commonly signified by the Greek letter σ (sigma), but κ (kappa) (especially in electrical engineering) and γ (gamma) are sometimes used.

Answer:

There are five (5) unknown support reactions in this problem.

Explanation:

A roller joint rotates and translates along the surface on which the roller rests. The resulting reaction force is always a single force that is perpendicular to, and away from, the surface. This allows the roller to move in a single plane along the surface where it rests.

A cable support provides support in one direction, parallel, and in opposite direction to the load on it. There exists a single reaction from the cable pointed upwards.

A ball-and-socket joint have  reaction forces in all 3 cardinal  directions. This allows it to move in the x-y-z plane.

The total unknown reactions on the member are five in number.

Answer:

A) flow depth after jump = 2.46 m,  Froude number after jump = 0.464

B) head loss = 0.572 m

C) dissipation ratio = 0.173

Explanation:

Given data :

width of channel = 10-m

velocity of before jump (V1) = 7 m/ s

flow depth before jump (y1) = 0.8 m

A) determining the flow depth and the Froude's number after the jump

attached below is the solution

B) head loss

HL = Y1 -Y2 + [tex]\frac{V_{1} ^2 - V_{2} ^2}{2g}[/tex] = 0.8 - 2.46 + [tex]\frac{49 - 5.1984}{19.62}[/tex] = 0.572

C) dissipation ratio

HL / Es1 = 0.572 / 3.3 = 0.173

Es1 = 0.8 + [tex]\frac{7^2}{2*9.81}[/tex] = 0.173

Answer:

  11.94 V

Explanation:

Generally the regulated voltage drops as load increases. When the voltage has dropped by 0.5%, it will be 60 mV less than the nominal value:

  12.0 V - 0.06 V = 11.94 V . . . . full load voltage

Answer:

The Remaining Bulbs will either burn out( draw more current ) or Not burn out depending on the arrangement of the bulbs in the circuit

Explanation:

The Remaining Bulbs will either burn more brightly ( draw more current ) or Burn less brightly ( draw less current).and this depends on the arrangement of the light bulbs in the various circuit.

If the light bulbs are connected in series the remaining bulbs will burn out as soon as  any light bulb burns out and this is because bulbs connected in series receive the same amount of current ,

If the light bulbs are connected in parallel the remaining bulbs will not burn out because each bulb receives current based on its resistance.

Answer:

moment of inertia = 4.662 * 10^6 [tex]mm^4[/tex]

Explanation:

Given data :

Mass of machine = 400 kg = 400 * 9.81 = 3924 N

length of span = 3.2 m

E = 200 * 10^9 N/m^2

frequency = 9.3 Hz

Wm ( angular frequency ) = 2 [tex]\pi f[/tex] = 58.434 rad/secs

also Wm = [tex]\sqrt{\frac{g}{t} }[/tex]  ------- EQUATION 1

g = 9.81

deflection of simply supported beam

t = [tex]\frac{wl^3}{48EI}[/tex]

insert the value of t into equation 1

W[tex]m^2[/tex] = [tex]\frac{g*48*E*I}{WL^3}[/tex]   make I the subject of the equation

I ( Moment of inertia about the neutral axis ) = [tex]\frac{WL^3* Wn^2}{48*g*E}[/tex]

I = [tex]\frac{3924*3.2^3*58.434^2}{48*9.81*200*10^9}[/tex]  = 4.662 * 10^6 [tex]mm^4[/tex]

Answer:

As the asteroid falls closer to the Earth's surface its Gravitational Potential energy decreases and its Kinetic energy increases.

Answer:

the rate of heat loss from the duct to the attic space = 1315.44 W

the pressure difference between the inlet and outlet sections of the duct  = 7.0045 N/m²

Explanation:

We know that properties of air 80⁰C  and 1atm  (from appendix table) are;

density p = 0.9994 kg/m³, Specifice heat Cp = 1008 J/kg.⁰C

Thermal conductivity k = 0.02953 W/m.⁰C, Prandtl number Pr = 0.7154,

Kinematic viscosity v = 2.097 × 10⁻⁵ m²/s

haven gotten that, we calculate the hydraulic diameter of square duct

Dh = 4Ac / P      { Ac = is cross sectional area of duct and P = perimeter}

now we substitute a² for Ac and 4a for P ( we know from the question that a = 0.2 m)

Dh = 4a² / 4a

Dh = 4(0.2)² / 4(0.2)

Dh = 0.2 m

Now we calculate the average velocity of air

Vₐ = Vˣ / Ac        { vˣ = volume flow rate of air}

Vₐ = Vˣ / a²      { Ac = a² }, we know that a = 0.2m₂, Vˣ = 0.15 m³

Vₐ = 0.15 / (0.2)²

Vₐ = 3.75 m/s

Next we calculate the Reynolds number

Re = Vₐ Dh / V

Re = (3.75 × 0.2) / 2.097× 10⁻⁵

Re = 35765.379

The  Reynolds number IS GREATER than 10,000

so the flow is turbulent and entry length in this case is nearly 10 times the hydraulic diameter

Lh ≈ Lt ≈ 10D

= 10 × 0.2

= 2m

As this length is quite small when compared to the total of tube, we assume fully developed flow for the entire tube length.

Now we calculate the Nusselt number from this relation;

Nu =  0.023 Re⁰'⁸ Pr⁰'³

so we substitute for Re and Pr

Nu = 0.023(35765.379)⁰'⁸ (0.7154)⁰'³

Nu = 91.4

Now calculate the convective heat transfer coefficient

h = Nu × K/ Dh

we substitute

h = 91.4 × 0.02953 W/m.°C / 0.2 m

h = 13.5 W/m².°C

We calculate the surface area of the square duct

Aₓ = 4aL       { L= length of duct}

we substitute

Aₓ = 4 × 0.2 × 8

Aₓ = 6.4 m²

Mass flow rate of air

m = pVˣ

we substitute again ( from our initials)

m = 0.9994 kg/m₃ × 0.15 m³/s

m= 0.150 kg/s

We calculate the exit temperature of the air from the duct

Te = Ts - (Ts -Ti) exp ( - hAₓ / mCp)

we know that

Ts = 60°C , Ti = 80°C, h = 13.5 W/m².°C , Aₓ = 6.4m², m = 0.150 kg/s , Cp = 1008 J/kg.°C

we substitute

Te = 60 - (60-80) exp(- ((13.5 × 6.4)/(0.15 × 1008))

Te = 71.3°

Now we calculate the rate of heat loss from the duct.

Q = mCp ( Ti -Te )

we substitute again

Q = 0.150 × 1008 × ( 80 - 71.3 )

Q = 1315.44 W

Next we calculate the estimated friction factors by using Haaland equation

1/√f = - 1.8log₁₀ [ 6.9/Re + (E/D)/3.7)¹'¹¹]

we know that E/D = relative roughness = 10⁻³

we substitute

so

1/√f = - 1.8log₁₀ [ (6.9/35765.379) + ( 10⁻³/3.7)¹'¹¹]

1/√f = - 1.8log₁₀ { 0.000192924 + 0.00010947}

1/√f = - 1.8log₁₀ 0.000302324  

√f =   1/6.334

f = (1/6.334)²

f = 0.02492

We calculate the pressure difference between inlet and outlet sections of the duct

ΔPl = fLPVa² / Dh × 2

ΔPl = {0.02492 × 8 × 0.9994 × (3.75)²} / 0.2 × 2

ΔPl = 2.8018 / 0.4

ΔPl = 7.0045 N/m²

Therefore pressure deference is 7.0045 N/m²

Answer:

Average heat transfer coefficient =  31 kw/m^2 k

Heat transfer rate per meter length of pipe =  116.808 KW

Explanation:

water temperature = 20⁰c,  

free-stream velocity = 1.5 m/s

circular pipe diameter = 2.0 cm = 0.02 m

surface temperature = 80⁰c

A) calculate average heat transfer coefficient

we apply the formula below :

m = αAv

A (area) = [tex]\pi /4 (d)^2[/tex]

m = 10^3 * [tex]\pi / 4 ( 0.02)^2[/tex] * 1.5

   = 10^3 * 0.7857( 0.0004) * 1.5

   = 0.4714 kg/s

Average heat transfer coefficient  

h = [tex]\frac{m(cp)}{A}[/tex]  ,  A = [tex]\pi DL[/tex]

L = 1 m , m = 0.4714 kgs , cp = 4.18

back to equation

h = [tex]\frac{0.4714*4.18}{\pi * 0.02 }[/tex]   = 1.970 / 0.0628 = 31.369 ≈ 31 kw/m^2 k

B) Heat transfer rate per meter length of pipe

Q = ha( ΔT ),  a = [tex]\pi DL[/tex]

   = 31 * 0.0628 * ( 80 - 20 )

  = 31 * 0.0628 * 60 = 116.808 KW

Answer:

a. myMethod() has access to and can use myField.

Explanation:

Logic programming is a kind of programming which is largely based on formal logic.  The statement are written in logical forms which express rules about the domain. In the given scenario the my method will have access to my field which is private field. My method non static public field can also use my field class.

Answer:

It's easier to buy one, but you can search for a tutorial on how to make one on Yuotube.

There are quite a few videos on how to make one.