A horizontal force of magnitude 35.0N pushes a block of mass 4.00kg across a floor where the coefficient of kinetic friction is 0.600. (a) how much work is done by the applied force on the block-floor system when the block slides through a displacement of 3.00m across the floor? (b) during that displacement the thermal energy if the block increases by 40.0J. what is the increase in thermal energy of the floor? (c) what is the increase in the kinetic energy of the block?

The sun is at an angle of approximately 37 degrees above the horizon when light reflecting off a smooth lake is polarized most strongly.

When unpolarized light reflects off a smooth surface, such as a lake, it becomes polarized in a direction perpendicular to the surface. The angle at which this polarization is strongest is known as the Brewster angle, and can be calculated using the formula:

θB = arctan(n2/n1)

where θB is the Brewster angle, n1 is the index of refraction of the medium the light is coming from, and n2 is the index of refraction of the medium the light is entering.

For water, the index of refraction is approximately 1.33, and for air it is approximately 1.00. Plugging these values into the formula, we get:

θB = arctan(1.33/1.00) = 53.1 degrees

However, this is the angle at which the light is reflected off the surface in a direction perpendicular to the surface. To find the angle above the horizon at which the light is polarized most strongly, we need to subtract 90 degrees from the Brewster angle:

37 degrees = 90 degrees - 53.1 degrees

Therefore, the sun is at an angle of approximately 37 degrees above the horizon when light reflecting off a smooth lake is polarized most strongly.

For more similar questions on Brewster angle:

brainly.com/question/29428422

#SPJ11

(a) The current in the 8.00 Ω resistor connected to a battery that has an internal resistance of 0.15 Ω and a terminal voltage of 9.00 V is 1.0 A.

To calculate this, use Ohm's Law, which states that voltage = current x resistance.

Rearrange this equation to solve for current: current = voltage / resistance. Plug in the values for voltage and resistance to get:

current = 9.00 V / 8.00 Ω + 0.15 Ω = 1.0 A.

(b) The EMF (electromotive force) of the battery is 9.00 V. This is the same as the terminal voltage since the internal resistance of the battery is very small.

Learn more about resistance at : https://brainly.com/question/24119414

#SPJ11

The net charge of a solid plastic cylinder of radius 2.33 cm and length 6.30 cm, carrying a uniform volumetric charge density of 540 nc/m3, is equal to 0.0583 nC (nanocoulombs)

To determine the net charge of a cylinder, the formula Q =ρV has to be used where Q is the net charge, ρ is the uniform volumetric charge density, and V is the volume of the cylinder.

ρ is given as 540 nc/m³.

V is calculated using the formula

V = πr²h

where r is the radius and h is the length.

π is approximated to be 3.14.  

h is given as 6.30cm

r is 2.33cm

so the calculation for V becomes;

V = πr²h

V = 3.14 x 2.33² x 6.3

V = 108.02 cm³ or 108.02 x 10⁻⁶ m³.

Substitute the values of Q and V into the equation and solve for Q:

Q = ρVQ = 540 nc/m³ x 108.02 x 10⁻⁶ m³

Q = 0.0583 nc (to 3 decimal places)

Therefore the net charge of this cylinder, in nc (nanocoulombs) is 0.0583nc.

Learn more about net charge at https://brainly.com/question/26036371

#SPJ11

Acceleration due to gravity is 9.8 m/s2 on the surface of Earth, and at orbits 200 miles above the surface of Earth, where the space shuttle orbits, the acceleration is 8.78 m/s².

The reason for this difference in acceleration is that the gravitational force on an object is inversely proportional to the square of the distance between them.

Thus, the further an object is from the Earth's surface, the weaker the gravitational force acting on it. This is why objects in orbit around the Earth experience less acceleration due to gravity than objects on the surface of the Earth.

To know more about gravitational force:

https://brainly.com/question/3009841

#SPJ11

Answer:

Yo dude, if you had a beaker of liquid in outer space, it wouldn't push down on the bottom or the sides of the beaker like it would on Earth. In space, there's no gravity to make the liquid settle down, so it forms a round shape because of surface tension. So basically, the liquid would just float around in a ball inside the beaker. If you moved the beaker around, the liquid would just roll around with it like a bouncy ball.

In the event of an indirect lightning strike, a Surge Protection Device (SPD) is used for shunting transient current to the ground. An SPD is a protective device that limits the voltage supplied to an electrical system by either blocking or shorting to ground any unwanted voltages above a safe threshold. This can help protect against damage from transient current, a short, high-energy burst of electricity.

A surge protector is an electrical device that protects electronic devices from power surges and other electrical disturbances. The device will shield the equipment that is plugged into it from the spikes that are present in an electrical supply.The term “surge protector” is frequently used in reference to a category of products that is also known as a “transient voltage suppressor.” This name provides insight into how these devices work. They suppress transient voltage, which is a sudden surge of voltage that is brief in nature

.How do surge protectors work?

Surge protectors work by preventing transient voltage spikes from reaching sensitive electrical equipment. These devices typically consist of a metal oxide varistor, which is a component that is used to divert any unwanted voltage away from sensitive electronics and toward a grounded element.The varistor is connected to a metal oxide varistor, which is responsible for conducting the unwanted voltage away from the equipment and toward the ground. Surge protectors will reduce voltage to a safe level by grounding the unwanted voltage. Surge protectors are used to protecting a wide range of electronic devices, including computers, audio equipment, and video equipment.

For more details go through the link: https://brainly.com/question/30869810

#SPJ11

Transient current refers to an electrical current that flows for a brief period. Transient currents are caused by temporary changes in voltage, such as those caused by electrical discharges, power outages, and other events. Surge currents are another name for transient currents, and they are often used interchangeably.

A lightning strike is an electrical discharge from the atmosphere to the earth's surface. Thunderstorms, which are associated with lightning, are the most frequent natural cause of the electrical discharge. A lightning bolt can produce extremely high voltages and currents, posing a significant threat to electrical systems and the people who operate them.

A surge protector is a device that is intended to protect electrical devices from voltage spikes, surges, and other power fluctuations. Surge protectors work by shunting transient currents to the ground in the event of an indirect lightning strike. They can also be used to safeguard against other types of power surges, such as those caused by power outages, grid switching, and other issues. Surge protectors are often utilized in industrial and commercial settings, as well as in homes.

For more information regarding this topic, you can click the below link

https://brainly.com/question/1100341

#SPJ11

A 0.400 kg mass hangs from a string with a length of 0.9 m, forming a conical pendulum. the period of the pendulum in a perfect circle is 1.4 s then the angle of pendulum is 14.68°.

Given:

Mass of the object = 0.4kg

Length of string = 0.9m

Period of conical pendulum = 1.4s

The angle of pendulum is calculated by using this formula :

T = 2π(r/g)1/2

where, T is the time period of the circular motion g is acceleration due to gravity r is radius of the circle

Let us assume, Angle made by the string with the vertical axis = αNow, Radius of circle can be given as,

R = l.sinα

Given the period of the conical pendulum as 1.4s

we can find the acceleration due to gravity as follows = 2π(r/g)1/2r = l.sinα2π(r/g)1/2 = Tg = 4π2(l.sinα)2/T2g = 4π2(l2sin2α)/T2sinα = gT2/4π2l2Sinα = (9.8 m/s2× 1.4 s2)/(4π2 × (0.9 m)2)Sinα = 0.253α = sin-1(0.253)α = 14.68°

Hence, the angle made by the string with the vertical axis is 14.68°.

To know more about Pendulum please visit :

https://brainly.com/question/29225143

#SPJ11

The correct option is A, A block of ice of the same mass is set sliding across the floor with the same speed along a parallel line The ice has more kinetic energy.

Kinetic energy is a type of energy that an object possesses by virtue of its motion. It is defined as the energy an object has due to its motion and is proportional to the mass of the object and the square of its velocity. The formula for kinetic energy is KE = 1/2mv², where m is the mass of the object and v is its velocity.

Kinetic energy is a scalar quantity and has units of joules in the International System of Units (SI). It is a fundamental concept in physics and is used to describe many physical phenomena, including the motion of particles, the behavior of gases, and the motion of waves. In many cases, kinetic energy can be transformed into other forms of energy. For example, when a ball is thrown upwards, its kinetic energy is gradually converted into gravitational potential energy as it moves higher and higher.

To learn more about Kinetic energy visit here:

brainly.com/question/26472013

#SPJ4

Complete Question:

Basketball rolls across a floor without slipping, with its center of mass moving at a certain velocity. A block of ice of the same mass is set sliding across the floor with the same speed along a parallel line.(a) How do their energies compare?

A). The ice has more kinetic energy.

B). They have equal kinetic energies.

C). The basketball has more kinetic energy.

Ceteris paribus, a decrease in capital productivity is the event that would cause both the equilibrium interest rate and the equilibrium quantity of investment to fall. The correct answer is option C.

Ceteris paribus is a Latin expression that means "all other things being equal." Ceteris paribus is a model in which economists use to analyze the effect of one independent variable on a dependent variable while keeping all other independent variables constant. This implies that only one variable is allowed to change while all other variables are held constant at their current level or position.

Therefore, Ceteris paribus, an increase in investor confidence, an increase in cosmetic income and wealth, and a strength of time preference will not cause both the equilibrium interest rate and the equilibrium quantity of investment to fall. However, a decrease in capital productivity is an event that would cause both the equilibrium interest rate and the equilibrium quantity of investment to fall.

When capital productivity is low, firms are unable to produce goods and services efficiently, and as a result, the demand for investment falls. When the demand for investment falls, the equilibrium quantity of investment will also decrease, leading to a decrease in the equilibrium interest rate.

To know more about Ceteris paribus, refer here:

https://brainly.com/question/13864080#

#SPJ11

Alpha particle emission, beta particle emission, and electron capture are all common types of radioactive decay.The correct answer is D.

They are common types of radioactive decay's because:

Option D includes all of these types of radioactive decay (alpha particle emission, beta particle emission, and electron capture), so it is the correct answer

To learn more about radioactive decay:

https://brainly.com/question/11117468

#SPJ11

Answer:

Explanation:

Using Kirchhoff's laws, we can solve for the current i:

At the node where the 2Ω and 4Ω resistors meet, the current is split into two branches, i and i1. Applying Kirchhoff's current law (KCL), we have:

i + i1 = 12/2 = 6 A

At the loop with the 2Ω, 4Ω, and 5Ω resistors, applying Kirchhoff's voltage law (KVL), we have:

-20 + 2i + 4i1 + 5i1 = 0

-20 + 6i1 + 2i = 0

6i1 + 2i = 20

3i1 + i = 10

We can solve this system of equations by substitution, which gives:

i = 2 A

Therefore, the current through the 2Ω resistor is 2 A. The answer is (A) 2 A.

There are 7.86 x 10²³ electrons in a 30.0 cm length of 12-gauge copper wire with a diameter of 2.05 mm.

To calculate the number of electrons in a 30.0 cm length of 12-gauge copper wire (diameter 2.05 mm), you can use the following equation:

n = ρV / m

where:

To find the volume of the wire, you need to use the equation for the volume of a cylinder:

Where:

Therefore, V = π(1.025 mm)²(30.0 cm) = 9.30 cm³The mass of one copper atom is 63.55 g/mol or 1.054 x 10⁻²² g. To find m, you need to use Avogadro's number (6.02 x 10^23 atoms/mol):m = (63.55 g/mol) / (6.02 x 10^23 atoms/mol) = 1.055 x 10⁻²² g

Now, you can plug in the values:

n = (8.96 g/cm³)(9.30 cm³) / (1.055 x 10⁻²² g) = 7.86 x 10²³ electrons

Therefore, there are 7.86 x 10²³ electrons in a 30.0 cm length of 12-gauge copper wire with a diameter of 2.05 mm. This should be rounded to 2 significant figures, so the final answer is 7.9 x 10²³ electrons.

Learn more about electrons: https://brainly.com/question/26084288

#SPJ11

Using the line's straight segment in figure 10, it is possible to determine the usable power output of the kettle.

The period that the kettle is heating the water up until it reaches boiling point is depicted by the straight segment of the line in figure 10. Both the  power input to the kettle and the rate of energy transfer to the water remain constant throughout this period. Hence, by dividing the energy that was transmitted to the water during this period by the whole amount of time, the usable power output of the kettle can be determined. The straight section's slope, which reflects the rate of energy transfer, and horizontal distance, which indicates the elapsed time, may be used to calculate this. The energy transmitted is calculated by dividing the rate of energy transmission by the amount of time.

learn more about  power here:

https://brainly.com/question/22285866

#SPJ4

Running on a treadmill is slightly easier than running outside because there is no drag force to work against. Suppose a 60 kg runner completes a 5.0 km race in 22 minutes. The drag force on the runner during the race is 13.4 N.

Running on a treadmill is slightly easier than running outside because there is no drag force to work against. Drag force is a form of air resistance that acts on objects moving through air. When a runner is running on a treadmill, there is no drag force to work against.

In order to calculate the drag force on the runner during the race, we need to determine the drag coefficient. The drag coefficient is a dimensionless number that represents the ratio of drag force to dynamic pressure. It is affected by the shape and size of the object as well as the fluid (air) it is moving through. Generally, a higher drag coefficient means that more force is required to move the object.

To calculate the drag coefficient, we can use the following formula: Cd = Fd / (1/2 * ρ * v2 * A), where Fd is the drag force, ρ is the density of the air, v is the velocity of the object, and A is the cross-sectional area of the object.

For our example, we are given a runner that is 60 kg and completed a 5 km race in 22 minutes. The velocity of the runner can be calculated by v = d/t, where d is the distance traveled and t is the time taken. This gives us a velocity of 8.3 m/s. The density of the air is given to be 1.2 kg/m3 and the cross-sectional area is 0.72 m2.

Plugging these values into the formula gives us a drag coefficient of 0.385. This means that for every 1 unit of dynamic pressure, the drag force is 0.385. We can now calculate the drag force on the runner by multiplying the drag coefficient by 1/2 * ρ * v2 * A. In this case, the drag force is 13.4 N.

In conclusion, the drag force on the runner during the race is 13.4 N. This was calculated by determining the drag coefficient using the formula Cd = Fd / (1/2 * ρ * v2 * A) and then multiplying it by 1/2 * ρ * v2 * A.

For more such questions on Drag force.

https://brainly.com/question/12774964#

#SPJ11

Answer:

A diameter is also a double of radius

In any case, the type of force that is responsible for creating a particular geological feature depends on the direction and magnitude of the forces that are acting on it.

Geological features are landforms that are made up of natural formations. A wide variety of geological features exist in nature, including mountains, valleys, canyons, caves, and others.

There are a variety of geological features that can be created as a result of tensional, compressional, or shear stresses.

Let's take a closer look at each type of stress:

Tensional: Tensional forces act to pull rocks apart. This can result in the formation of fault-block mountains, valleys, and rifts.

Compressional: Compressional forces act to push rocks together. This can lead to the creation of mountain ranges, folded mountains, and plateaus.

Shear Stresses: Shear stresses act to twist or bend rocks. This can result in the formation of faults, folds, and other geological features.

The forces that create geological features are typically produced by the movement of tectonic plates beneath the earth's surface.

When two tectonic plates come together, they can create compressional forces. When they move apart, they can create tensional forces.

When they slide past each other, they can create shear stresses. Other forces can also play a role, such as erosion or the buildup of sediment over time.

To know more about Geological features:https://brainly.com/question/19925491

#SPJ11

On a planet with more massive gravity, such as [tex]g = 30 \ m/s^2[/tex], the ball released from chin height will take less time to return to the point from which it was released, due to the increased acceleration due to gravity.

It will take less time to return to the point from which it was released. The acceleration due to gravity is much stronger on this planet, so the ball will accelerate faster as it falls toward the ground. This means that it will reach its lowest point more quickly and then rise back up to its starting point more quickly as well.

Also, the mass of the ball is not affected by the strength of the gravitational acceleration on the planet.

Learn more about acceleration:

https://brainly.com/question/460763

#SPJ11

The angular acceleration of the fan is 0.740 rad/s^2,

Angular acceleration which represents the rate at which the angular velocity changes over time. The unit used to measure angular acceleration is radians per square second (rad/s2), according to the International System of Units. The Greek alphabet symbol alpha (α) is used to denote angular acceleration.

To calculate the angular acceleration of the fan, the formula α = Δω/Δt is used. Here, α represents angular acceleration, Δω represents the change in angular speed, and Δt represents the change in time.

In this scenario, Δω is equal to 10.0 - 6.30 = 3.70 rad/s, and Δt is equal to 5.00 s. By substituting these values into the formula, we obtain α = 3.70/5.00 = 0.740 rad/s^2.

To gain more knowledge about angular acceleration, refer to brainly.com/question/21278452.

#SPJ11

Explanation:

Refer to pic...........

The center of mass of the two-car system can be found by taking the weighted average of the velocities of the two cars.

The velocity of the center of mass is the average of the two cars' velocities, weighted by their masses. The velocity of the center of mass is:

Velocity of Center of Mass = (1.27 x 103 kg x 11.6 m/s + 1.70 x 103 kg x 11.6 m/s) / (1.27 x 103 kg + 1.70 x 103 kg) = 11.60 m/s.

Read more about the topic velocity:

https://brainly.com/question/80295?source=archive

#SPJ11

A bar magnet falls under the influence of gravity along the axis of a long copper tube. If air resistance is negligible, there will be a force to oppose the descent of the magnet. The magnet will reach a terminal velocity. Here's why:

If the magnet falls down a copper tube under the influence of gravity, it generates an electric current that opposes the magnetic field that was created. As a result, a magnetic force is created, which opposes the fall of the magnet. As a result, there is a force opposing the descent of the magnet.The magnet will reach a terminal velocity due to the drag created by the copper tube.

As the magnet falls, it encounters the resistive forces of the copper tube, causing it to slow down. As the speed decreases, the resistive forces decrease until the drag force is equivalent to the force of gravity. The magnet then reaches a steady state called the terminal velocity. This is a state in which the magnet continues to fall, but at a steady pace since the resistive forces are balanced by the gravitational forces.

Learn more about magnetic force: https://brainly.com/question/29252577

#SPJ11

Log2(100) is 6.64 to 2 decimal places. Rounded up to the next highest integer, it is 7. Based on the tests done, the maximum number of iterations used for quick search on a collection of 100 items is 7 iterations.

The maximum number of iterations used for linear search on a collection of 100 items is 100 iterations. The big O of quick search is O(n log n).

log2(100) is the same as x in 2^x=100

This means 2^6.64=100

To solve for 6.64, take the logarithm of both sides.

log(2^6.64)=log(100)

6.64log(2)=log(100)

6.64=2log(10)+2log(5)

log(2)+log(1.25)+log(10)=6.64

log(2)+log(1.25)=6.64-log(10)

log(2)+log(1.25)=2.02

log(2x1.25)=2.02x2^(log(2)+log(1.25))=2.02 x 2^(log(10))=7 (rounded up)

The maximum number of iterations used for quick search on a collection of 100 items is 7 iterations.

The maximum number of iterations used for linear search on a collection of 100 items is 100 iterations. In big O notation, the time complexity of linear search is O(n).

To learn more about "log2(100)", visit: https://brainly.com/question/15602305

#SPJ11

i) The velocity of the particle at 17 sec is 17m/s.

ii) The total distance travelled is 190 m.

iii) The total displacement is -10m.

Distance is the length of any path connecting any two places. As measured along the shortest path between any two points, displacement is the direct distance between them.

The direction is ignored when calculating distance. The direction is accounted for in the displacement calculation.

Since it solely depends on magnitude and not direction, distance is a scalar number. Since displacement varies on both magnitude and direction, it is a vector quantity.

Distance provides specific directions that must be taken when moving from one location to another. Displacement only provides a partial description of the route because it pertains to the quickest way.

Velocity of particle = Slope of the object =Δ [tex]\frac{y}{x}[/tex]

Velocity = [tex]\frac{95-10}{20-15}[/tex] = 17m/s

To know more about Displacement, visit:

https://brainly.com/question/11934397

#SPJ1

a.  the depth of cut  is 0.625 inches.

b. the material removal rate is 0.003125 cubic inches per minute.

c. the time required to complete the cutting pass is 20 minutes.

a) The required depth of cut can be determined by :

DOC = (4 in - 2.75 in)/2 = 0.625 in

Therefore, the depth of cut is  0.625 inches.

b) The material removal rate can be found by applying:

MRR = DOC x Width of cut x Feed rate

assuming we are using a standard carbide insert tool with a width of cut of 0.5 inches.

MRR = 0.625 in x 0.5 in x 0.010 in/rev = 0.003125 cubic inches per minute

c) The time required to complete the cutting pass is determined by:

Time = Length of cut / (Cutting speed x Width of cut x Feed rate)

Time = 48 in / (400 ft/min x (0.5 in) x (0.010 in/rev) x (1/12 ft/in)) = 20 minutes

Learn more about material removal rate  at: https://brainly.com/question/13106351

#SPJ1

Price elasticity of demand for radios is 1 and total revenue from radio sales will remain constant.

Price elasticity of demand is calculated as the percentage change in quantity demanded divided by the percentage change in price. Using this formula, we can calculate the price elasticity of demand for radios as follows:

Price elasticity of demand = (percentage change in quantity demanded) / (percentage change in price)

Given that when the price of radios decreases by 5%, quantity demanded increases by 5%.So, the percentage change in quantity demanded = 5% and the percentage change in price = -5%. (Because price has decreased by 5%.)Price elasticity of demand = (5% / -5%) = -1.The negative sign indicates that the demand is elastic. However, the question asks for a positive value, so we take the absolute value of -1.Price elasticity of demand = 1.

Therefore, the price elasticity of demand for radios is 1.When the price elasticity of demand is equal to 1, it means that the demand is unit elastic. This implies that the percentage change in quantity demanded is equal to the percentage change in price. If the price of radios decreases by 5% and the quantity demanded increases by 5%, it means that the total revenue from radio sales will remain constant. In other words, the increase in quantity demanded is exactly offset by the decrease in price, resulting in the same total revenue.

More price elasticity: https://brainly.com/question/22716533

#SPJ11

The best example that shows the potential energy is a body at rest from some height from the ground, thus the correct answer is option b.

Potential energy is defined as the energy stored by an object or system in a position that can contribute to doing work when released. It is the stored energy of an object or system.

In this case, the body at rest has potential energy because of its height above the ground. As it falls, the potential energy is converted to kinetic energy.

Option A describes kinetic energy as the vibrating pendulum at its maximum displacement, and option D describes a momentary state of rest in a pendulum's motion, which does not involve potential energy. Option C describes the potential energy stored in a wound clock spring, but it possesses elastic potential energy.

Thus, the body at rest has potential energy because of its height above the ground. Thus, option b is correct.

Learn more about Potential energy here:

https://brainly.com/question/14427111

#SPJ11

A change in velocity in short period of time means the acceleration is large, hence the net force must be proportionately large as well.

A force is a physical quantity that induces a body to undergo an alteration in speed, direction of motion, or shape. A force can be classified as a push or a pull. When forces are equal, the forces are balanced and the object is not moving. Otherwise, if the forces are not equal, making it unbalanced will not give the object any movement.

The force that induces the change in the speed or direction of an object is referred to as a net force. The net force is equal to the product of the mass of the object and its acceleration. Newton (N) is the unit of measurement for force.

When a ball bounces against a wall, there will be a large change in velocity in a short period of time. This means the acceleration is large, hence the net force must be proportionately large as well.

Learn more about acceleration here: https://brainly.com/question/26408808

#SPJ11

a. To calculate the probability of a defect, we need to find the area under the normal distribution curve that falls outside the control limits of 11.664 and 12.336 ounces. We can calculate the z-scores for these limits as follows:

[tex]z_1 = (11.664 - 12) / 0.14 = -2.4[/tex]

[tex]z_2 = (12.336 - 12) / 0.14 = 2.4[/tex]

Using a standard normal distribution table or calculator, we can find that the probability of a defect is approximately 0.0115 (to 4 decimals).

To find the expected number of defects in a production run of 1000 parts, we can use the formula for the binomial distribution:

[tex]P(X = k) = C(n, k) \times p^k \times (1-p)^{(n-k)}[/tex]

where P(X = k) is the probability of exactly k defects in a run of n parts, p is the probability of a single defect (0.0115 in this case), and C(n, k) is the binomial coefficient (the number of ways to choose k defects from n parts).

For k = 0, 1, 2, ..., we can calculate the probabilities and add them up to find the expected number of defects:

E(X) = sum(k=0 to n) [ P(X = k) ] = n * p

Substituting n = 1000 and p = 0.0115, we get:

[tex]E(X) = 1000 \times 0.0115 = 11.5[/tex]

So we can expect to find approximately 12 defects (to the nearest whole number) in a production run of 1000 parts.

b. With a reduced process standard deviation of 0.12, the z-scores for the control limits remain the same as in part a:

[tex]z_1 = (11.664 - 12) / 0.12 = -2.8[/tex]

[tex]z_2 = (12.336 - 12) / 0.12 = 2.8[/tex]

Using a standard normal distribution table or calculator, we can find that the probability of a defect is approximately 0.0004 (to 4 decimals).

To find the expected number of defects in a production run of 1000 parts, we can use the same formula as in part a:

[tex]E(X) = n \times p[/tex]

Substituting n = 1000 and p = 0.0004, we get:

[tex]E(X) = 1000 \times 0.0004 = 0.4[/tex]

So we can expect to find approximately 0 defects (to the nearest whole number) in a production run of 1000 parts.

However, it's important to note that this assumes the process is operating exactly at the mean weight of 12 ounces and there is no other source of variation. In practice, there may still be some small amount of variation that could result in a few defects.

Learn more about normal distribution:

https://brainly.com/question/4079902

#SPJ11

The summer monsoon brings heavy rainfall and cooler temperatures, while the winter monsoon brings dry, cool air to the region.

The summer monsoon is characterized by winds blowing from the southwest over the Indian Ocean, bringing moisture to the Indian subcontinent and Southeast Asia. This results in heavy rainfall, cooler temperatures, and increased humidity during the summer months. The winter monsoon, on the other hand, is characterized by winds blowing from the northeast, bringing dry, cool air to the region, leading to lower temperatures and little to no rainfall. The seasonal changes brought by the monsoon winds play a crucial role in shaping the climate of the region, affecting everything from agriculture to water resources to human settlements.

To know more about monsoons, here

brainly.com/question/22831604

#SPJ4

The maximum energy of photoelectrons from aluminium is 2.3 eV for radiation of 2000 Å and 0.90 eV for radiation of 3130 Å.

To calculate Planck's constant and the work function of aluminium, we need to use the equation:

 h = E2 - E1/ λ2 - λ1

Where h is Planck's constant, E1 and E2 are the maximum energy of photoelectrons for each wavelength, and λ1 and λ2 are the wavelengths.

Using the given data, we have:

h = (2.3 - 0.90) / (2000 - 3130)

Therefore, h = -1.4 eV / -930 Å, which simplifies to h = 0.0015 eVÅ.

The work function of aluminium is equal to the maximum energy of the photoelectrons for the longest wavelength, in this case, 0.90 eV. Therefore, the work function of aluminium is 0.90 eV.

Learn more  about photoelectrons  at brainly.com/question/16772624

#SPJ11