A hydraulic lift raises a 2 000-kg automobile when a 500-N force is applied to the smaller piston. If the smaller piston has an area of 10 cm2, what is the cross-sectional area of the larger piston

Answers

Answer 1

Answer:

The cross-sectional area of the larger piston is 392 cm²

Explanation:

Given;

output mass of the piston, m₀ = 2000 kg

input force of the piston, F₁ = 500 N

input area of the piston, A₁ = 10 cm² = 0.001 m²

The output force is given by;

F₀ = m₀g

F₀ = 2000 x 9.8

F₀ = 19600 N

The cross-sectional area of the larger piston or output area of the piston will be calculated by applying the following equations;

[tex]\frac{F_i}{A_i} = \frac{F_o}{A_o} \\\\A_o= \frac{F_o A_i}{F_i} \\\\A_o = \frac{19600*0.001}{500} \\\\A_o = 0.0392 \ m^2\\\\A_o = 392 \ cm^2[/tex]

Therefore, the cross-sectional area of the larger piston is 392 cm²


Related Questions

What is the reason for the increase and decrease size of the moon and write down in a paragraph.

Answers

Answer:

The reason for the increase or decrease of the moon is due to the angular perception of the moon.

Explanation:

Also called lunar illusion, this phenomenon is due to the position in which the moon is, it can be at the zenith or on the horizon, both distances are different from each other with respect to the position of the person.

The zenith is the highest part of the sky and the horizon the lowest.

When there are landmarks such as trees, buildings or mountains on the horizon, the illusion of closeness is given and the illusion of distance is misinterpreted.

But when looking up at the sky as there is no reference point there will be a failure in the perception of size.

Equal currents of magnitude I travel into the page in wire M and out of the page in wire N. The direction of the magnetic field at point P which is at the same distance from both wires is

Answers

Answer:

The direction of the magnetic field on point P, equidistant from both wires, and having equal magnitude of current flowing through them will be pointed perpendicularly away from the direction of the wires.

Explanation:

Using the right hand grip, the direction of the magnet field on the wire M is counterclockwise, and the direction of the magnetic field on wire N is clockwise. Using this ideas, we can see that the magnetic flux of both field due to the currents of the same magnitude through both wires, acting on a particle P equidistant from both wires will act in a direction perpendicularly away from both wires.

Monochromatic light is incident on a pair of slits that are separated by 0.220 mm. The screen is 2.60 m away from the slits. (Assume the small-angle approximation is valid here.)
(a) If the distance between the central bright fringe and either of the adjacent bright fringes is 1.97 cm, find the wavelength of the incident light.
(b) At what angle does the next set of bright fringes appear?

Answers

Answer:

a

   [tex]\lambda = 1.667 nm[/tex]

b

     [tex]\theta = 0.8681^o[/tex]

Explanation:

From the question we are told that

   The distance of separation is [tex]d = 0.220 \ mm = 0.00022 \ m[/tex]

    The  is distance of the screen from the slit is  [tex]D = 2.60 \ m[/tex]

    The distance between the central bright fringe and either of the adjacent bright   [tex]y = 1.97 cm = 1.97 *10^{-2}\ m[/tex]

Generally  the condition for constructive interference is  

      [tex]d sin \tha(\theta ) = n \lambda[/tex]

From the question we are told that small-angle approximation is valid here.

So    [tex]sin (\theta ) = \theta[/tex]

=>        [tex]d \theta = n \lambda[/tex]

=>        [tex]\theta = \frac{n * \lambda }{d }[/tex]

Here n is the order of maxima and the value is  n =  1 because we are considering the central bright fringe and either of the adjacent bright fringes

Generally the distance between the central bright fringe and either of the adjacent bright  is mathematically represented as

         [tex]y = D * sin (\theta )[/tex]

From the question we are told that small-angle approximation is valid here.

So

       [tex]y = D * \theta[/tex]

=>   [tex]\theta = \frac{ y}{D}[/tex]

So

     [tex]\frac{n * \lambda }{d } = \frac{y}{D}[/tex]

     [tex]\lambda =\frac{d * y }{n * D}[/tex]

substituting values

       [tex]\lambda = \frac{0.00022 * 1.97*10^{-2} }{1 * 2.60 }[/tex]

        [tex]\lambda = 1.667 *10^{-6}[/tex]

        [tex]\lambda = 1.667 nm[/tex]

In the b part of the question we are considering the next set of bright fringe so  n=  2

    Hence

     [tex]dsin (\theta ) = n \lambda[/tex]

    [tex]\theta = sin^{-1}[\frac{ n * \lambda }{d} ][/tex]

    [tex]\theta = sin^{-1}[\frac{ 2 * 1667 *10^{-9}}{ 0.00022} ][/tex]

    [tex]\theta = 0.8681^o[/tex]

The momentum of an electron is 1.75 times larger than the value computed non-relativistically. What is the speed of the electron

Answers

Answer:

Speed of the electron is 2.46 x 10^8 m/s

Explanation:

momentum of the electron before relativistic effect = [tex]M_{0} V[/tex]

where [tex]M_{0}[/tex] is the rest mass of the electron

V is the velocity of the electron.

under relativistic effect, the mass increases.

under relativistic effect, the new mass M will be

M = [tex]M_{0}/ \sqrt{1 - \beta ^{2} }[/tex]

where

[tex]\beta = V/c[/tex]

c  is the speed of light = 3 x 10^8 m/s

V is the speed with which the electron travels.

The new momentum will therefore be

==> [tex]M_{0}V/ \sqrt{1 - \beta ^{2} }[/tex]

It is stated that the relativistic momentum is 1.75 times the non-relativistic momentum. Equating, we have

1.75[tex]M_{0} V[/tex] = [tex]M_{0}V/ \sqrt{1 - \beta ^{2} }[/tex]

the equation reduces to

1.75 = [tex]1/ \sqrt{1 - \beta ^{2} }[/tex]

square both sides of the equation, we have

3.0625 = 1/[tex](1 - \beta ^{2} )[/tex]

3.0625 - 3.0625[tex]\beta ^{2}[/tex] = 1

2.0625 = 3.0625[tex]\beta ^{2}[/tex]

[tex]\beta ^{2}[/tex] = 0.67

β = 0.819

substitute for  [tex]\beta = V/c[/tex]

V/c = 0.819

V = c x 0.819

V = 3 x 10^8 x 0.819 = 2.46 x 10^8 m/s

In a physics laboratory experiment, a coil with 250 turns enclosing an area of 14 cm2 is rotated in a time interval of 0.030 s from a position where its plane is perpendicular to the earth's magnetic field to a position where its plane is parallel to the field. The earth's magnetic field at the lab location is 5.0×10^−5 T.Required:a. What is the total magnetic flux through the coil before it is rotated? After it is rotated? b. What is the average emf induced in the coil?

Answers

Explanation:

Consider a loop of wire, which has an area of [tex]A=14 \mathrm{cm}^{2}[/tex] and [tex]N=250[/tex] turns, it is initially placed perpendicularly in the earth magnetic field. Then it is rotated from this position to a position where its plane is parallel to the field as shown in the following figure in [tex]\Delta t=0.030[/tex] s. Given that the earth's magnetic field at the position of the loop is [tex]B=5.0 \times 10^{-5} \mathrm{T}[/tex], the flux through the loop before it is rotated is,

[tex]\Phi_{B, i} &=B A \cos \left(\phi_{i}\right)=B A \cos \left(0^{\circ}\right[/tex]

[tex]=\left(5.0 \times 10^{-5} \mathrm{T}\right)\left(14 \times 10^{-4} \mathrm{m}^{2}\right)(1)[/tex]

[tex]=7.0 \times 10^{-8} \mathrm{Wb}[/tex]

[tex]\quad\left[\Phi_{B, i}=7.0 \times 10^{-8} \mathrm{Wb}\right[/tex]

after it is rotated, the angle between the area and the magnetic field is [tex]\phi=90^{\circ}[/tex] thus,

[tex]\Phi_{B, f}=B A \cos \left(\phi_{f}\right)=B A \cos \left(90^{\circ}\right)=0[/tex]

[tex]\qquad \Phi_{B, f}=0[/tex]

(b) The average magnitude of the emf induced in the coil equals the change in the flux divided by the time of this change, and multiplied by the number of turns, that is,

[tex]{\left|\mathcal{E}_{\mathrm{av}}\right|=N\left|\frac{\Phi_{B, f}-\Phi_{B, i}}{\Delta t}\right|}{=} & \frac{1.40 \times 10^{-5} \mathrm{Wb}}{0.030 \mathrm{s}}[/tex]

[tex]& 3.6 \times 10^{-4} \mathrm{V}=0.36 \mathrm{mV}[/tex]

[tex]\mathbb{E}=0.36 \mathrm{mV}[/tex]

(a) The initial and final flux through the coil is 1.75 × 10⁻⁵ Wb and 0 Wb

(b) The induced EMF in the coil is 0.583 mV

Flux and induced EMF:

Given that the coil has N = 250 turns

and an area of A = 14cm² = 1.4×10⁻³m².

It is rotated for a time period of Δt = 0.030s such that it is parallel with the earth's magnetic field that is B = 5×10⁻⁵T

(a) The flux passing through the coil is given by:

Ф = NBAcosθ

where θ is the angle between area vector and the magnetic field

The area vector is perpendicular to the plane of the coil.

So, initially, θ = 0°, as area vector and earth's magnetic field both are perpendicular to the plane of the coil

So the initial flux is:

Φ = NABcos0° = NAB

Ф = 250×1.4×10⁻³×5×10⁻⁵ Wb

Ф = 1.75 × 10⁻⁵ Wb

Finally, θ = 90°, and since cos90°, the final flux through the coil is 0

(b) The EMF induced is given by:

E = -ΔФ/Δt

E = -(0 - 1.75 × 10⁻⁵)/0.030

E = 0.583 × 10⁻³ V

E = 0.583 mV

Learn more about magnetic flux:

https://brainly.com/question/15359941?referrer=searchResults

Now the friends are ready to tackle a homework problem. A pulse is sent traveling along a rope under a tension of 29 N whose mass per unit length abruptly changes, from 19 kg/m to 45 kg/m. The length of the rope is 2.5 m for the first section and 2.8 m for the second, and the second rope is rigidly fixed to a wall. Two pulses will eventually be detected at the origin: the pulse that was reflected from the medium discontinuity and the pulse that was originally transmitted, which hits the wall and is reflected back and transmitted through the first rope. What is the time difference, Δt, between the two pulses detected at the origin? s

Answers

Answer:

The time difference is 2.97 sec.

Explanation:

Given that,

Tension = 29 N

Mass per unit length [tex]\mu_{1}=19\ kg/m[/tex]

Mass per unit length [tex]\mu_{2}=45\ kg/m[/tex]

Length of first section = 2.5 m

Length of second section = 2.8 m

We need to total distance of first pulse

Using formula for distance

[tex]d=2.5+2.5[/tex]

[tex]d_{1}=5.0\ m[/tex]

We need to total distance of second pulse

Using formula for distance

[tex]d=2.8+2.8[/tex]

[tex]d_{2}=5.6\ m[/tex]

We need to calculate the speed of pulse in the first string

Using formula of speed

[tex]v_{1}=\sqrt{\dfrac{T}{\mu_{1}}}[/tex]

Put the value into the formula

[tex]v_{1}=\sqrt{\dfrac{29}{19}}[/tex]

[tex]v_{1}=1.24\ m/s[/tex]

We need to calculate the speed of pulse in the second string

Using formula of speed

[tex]v_{2}=\sqrt{\dfrac{T}}{\mu_{2}}}[/tex]

Put the value into the formula

[tex]v_{2}=\sqrt{\dfrac{29}{45}}[/tex]

[tex]v_{2}=0.80\ m/s[/tex]

We need to calculate the time for first pulse

Using formula of time

[tex]t_{1}=\dfrac{d_{1}}{v_{1}}[/tex]

Put the value into the formula

[tex]t_{1}=\dfrac{5.0}{1.24}[/tex]

[tex]t_{1}=4.03\ sec[/tex]

We need to calculate the time for second pulse

Using formula of time

[tex]t_{2}=\dfrac{d_{1}}{v_{1}}[/tex]

Put the value into the formula

[tex]t_{2}=\dfrac{5.6}{0.80}[/tex]

[tex]t_{2}=7\ sec[/tex]

We need to calculate the time difference

Using formula of time difference

[tex]\Delta t=t_{2}-t_{1}[/tex]

Put the value into the formula

[tex]\Delta t=7-4.03[/tex]

[tex]\Delta t=2.97\ sec[/tex]

Hence, The time difference is 2.97 sec.

an electric device is plugged into a 110v wall socket. if the device consumes 500 w of power, what is the resistance of the device

Answers

Answer: R=24.2Ω

Explanation: Power is rate of work being done in an electric circuit. It relates to voltage, current and resistance through the following formulas:

P=V.i

P=R.i²

[tex]P=\frac{V^{2}}{R}[/tex]

The resistance of the system is:

[tex]P=\frac{V^{2}}{R}[/tex]

[tex]R=\frac{V^{2}}{P}[/tex]

[tex]R=\frac{110^{2}}{500}[/tex]

R = 24.2Ω

For the device, resistance is 24.2Ω.

which category would a person who has an IQ of 84 belong ?

Answers

answer: below average

An astronomer is measuring the electromagnetic radiation emitted by two stars, both of which are assumed to be perfect blackbody emitters. For each star she makes a plot of the radiation intensity per unit wavelength as a function of wavelength. She notices that the curve for star A has a maximum that occurs at a shorter wavelength than does the curve for star B. What can she conclude about the surface temperatures of the two stars

Answers

Answer:

Star A has a higher surface temperature than star B.

Explanation:

The effective temperature of a star can be determined by means of its spectrum and Wien's displacement law:

[tex]T = \frac{2.898x10^{-3} m. K}{\lambda max}[/tex] (1)

Where T is the effective temperature of the star and [tex]\lambda_{max}[/tex] is the maximum peak of emission.  

A body that is hot enough emits light as a consequence of its temperature. For example, if an iron bar is put in contact with fire, it will start to change colors as the temperature increase, until it gets to a blue color, that scenario is known as Wien's displacement law. Which establishes that the peak of emission for the spectrum will be displaced to shorter wavelengths as the temperature increase and higher wavelengths as the temperature decreases.

Therefore, star A has a higher surface temperature than star B, as it is shown in equation 1 since T and [tex]\lambda max[/tex] are inversely proportional.

B. CO
A wave has frequency of 2 Hz and a wave length of 30 cm. the velocity of the wave is
A. 60.0 ms
B. 6.0 ms
D. 0.6 ms​

Answers

Answer:

0.6 m/s

Explanation:

2Hz = 2^-1 = 2 /s

30cm = .3m

Velocity is in the units m/s, so multiplying wavelength in meters by the frequency will give you the velocity.

(.3m)*(2 /s) = 0.6 m/s

The answer is 0.6 ms

A lab technician uses laser light with a wavelength of 650 nmnm to test a diffraction grating. When the grating is 42.0 cmcm from the screen, the first-order maxima appear 6.09 cmcm from the center of the pattern. How many lines per millimeter does this grating have?

Answers

Answer:

221 lines per millimetre

Explanation:

We know that for a diffraction grating, dsinθ =mλ where d = spacing between grating, θ = angle to maximum, m = order of maximum and λ = wavelength of light.

Since the grating is 42.0 cm from the screen and its first order maximum (m = 1) is at 6.09 cm from the center of the pattern,

tanθ = 6.09 cm/42.0 cm = 0.145

From trig ratios, cot²θ + 1 = cosec²θ

cosecθ = √((1/tanθ)² + 1) = √((1/0.145)² + 1) = √48.562 = 6.969

sinθ = 1/cosecθ = 1/6.969 = 0.1435

Also, sinθ = mλ/d at the first-order maximum, m = 1. So

sinθ = (1)λ/d = λ/d

Equating both expressions we have  

0.1435 = λ/d

d = λ/0.1435

Now, λ = 650 nm = 650 × 10⁻⁹ m

d = 650 × 10⁻⁹ m/0.1435

d = 4529.62 × 10⁻⁹ m per line

d = 4.52962 × 10⁻⁶ m per line

d = 0.00452962 × 10⁻³ m per line

d = 0.00452962 mm per line

Since d = width of grating/number of lines of grating

Then number of lines per millimetre = 1/grating spacing

= 1/0.00452962

= 220.77 lines per millimetre

≅ 221 lines per millimetre since we can only have a whole number of lines.

The A block, with negligible dimensions and weight P, is supported by the coordinate point (1.1/2) of the parabolic fixed grounded surface, from equation y = x^2/2 If the block is about to slide, what is the coefficient of friction between it and the surface; determine the force F tangent to the surface, which must be applied to the block to start the upward movement.

Answers

Answer:

μ = 1

F = P√2

Explanation:

The parabola equation is: y = ½ x².

The slope of the tangent is dy/dx = x.

The angle between the tangent and the x-axis is θ = tan⁻¹(x).

At x = 1, θ = 45°.

Draw a free body diagram of the block.  There are three forces:

Weight force P pulling down,

Normal force N pushing perpendicular to the surface,

and friction force Nμ pushing up tangential to the surface.

Sum of forces in the perpendicular direction:

∑F = ma

N − P cos 45° = 0

N = P cos 45°

Sum of forces in the tangential direction:

∑F = ma

Nμ − P sin 45° = 0

Nμ = P sin 45°

μ = P sin 45° / N

μ = tan 45°

μ = 1

Draw a new free body diagram.  This time, friction force points down tangential to the surface, and applied force F pushes up tangential to the surface.

Sum of forces in the tangential direction:

∑F = ma

F − Nμ − P sin 45° = 0

F = Nμ + P sin 45°

F = (P cos 45°) μ + P sin 45°

F = P√2

Determine the orbital period (in hours) of an observation satellite in a circular orbit 1,787 km above Mars.

Answers

Answer:

T = 3.14 hours

Explanation:

We need to find the orbital period (in hours) of an observation satellite in a circular orbit 1,787 km above Mars.

We know that the radius of Mars is 3,389.5 km.

So, r = 1,787 + 3,389.5 = 5176.5 km

Using Kepler's law,

[tex]T^2=\dfrac{4\pi ^2}{GM}r^3[/tex]

M is mass of Mars, [tex]M=6.39\times 10^{23}\ kg[/tex]

So,

[tex]T^2=\dfrac{4\pi ^2}{6.67\times 10^{-11}\times 6.39\times 10^{23}}\times (5176.5 \times 10^3)^3\\\\T=\sqrt{\dfrac{4\pi^{2}}{6.67\times10^{-11}\times6.39\times10^{23}}\times(5176.5\times10^{3})^{3}}\\\\T=11334.98\ s[/tex]

or

T = 3.14 hours

So, the orbital period is 3.14 hours

Distinguish between physical and chemical changes. Include examples in your explanations.

Answers

Answer:

Chemical changes are recognized when a substance changes its properties permanently and it cannot be the same substance as before.

Instead the physical changes implies that if you can return to the same substance through a reverse process.

Explanation:

A chemical change is, by example, a combustion, if a sheet of paper burns, its result is ashes, the ashes cannot go back to being a sheet of paper because its properties changed, heat energy was generated that changed matter permanently.

A physical change, by example, is that of freezing water, the water becomes ice, but this can easily become water again if the temperature is increased, its properties do not change and the chemistry of the substance does not change.

A chemical change takes place when a chemical reaction takes place, while when a matter changes forms but not the chemical identity then a physical change takes place.  

A product or a new compound formation takes place from a chemical change as the rearrangement of atoms takes place to produce novel chemical bonds.  

• In a chemical change always a chemical reaction takes place.  

• Some of the chemical changes examples are souring milk, burning wood, digesting food, mixing acid and base, cooking food, etc.  

• In a physical change no new chemical species form.  

• The changing of the state of a pure substance between liquid, gas, or solid is a physical change as there is no change in the identity of the matter.  

• Some of the physical changes are melting of ice, tempering of steel, breaking a bottle, crumpling a sheet of aluminum foil, boiling water, and shredding paper.  

Thus, a new substance is formed during a chemical change, while a physical change does not give rise to a new substance.  

To know more about:

https://brainly.com/question/7279398

: A spaceship is traveling at the speed 2t 2 1 km/s (t is time in seconds). It is pointing directly away from earth and at time t 0 it is 1000 kilometers from earth. How far from earth is it at one minute from time t 0

Answers

Answer:

145060km

Explanation: Given that

speed = dx/dt = 2t^2 +1

integrate

x = 2/3t^3 + t + c (c is constant, x is in km, t is in second)

given that at t=0, x = 1000

so 1000 = 2/3 X (0)^3 + 0 + c

or c = 1000

So x = 2/3t^3 + t + 1000

for t = 1 min = 60s

x = 2/3 X 60^3 + 60 + 1000

x = 2/3×216000+ 1060

x = 144000+1060

= 145060km

At one minute, it will be 145060km far from the earth

Scientists today learn about the world by _____. 1. using untested hypotheses to revise theories 2. observing, measuring, testing, and explaining their ideas 3. formulating conclusions without testing them 4. changing scientific laws

Answers

Answer:

Option 2 (observing, measuring, testing, and explaining their ideas) is the correct choice.

Explanation:

A traditional perception of such a scientist is those of an individual who performs experiments in some kind of a white coat. The reality of the situation is, a researcher can indeed be described as an individual interested in the comprehensive as well as a recorded review of the occurrences occurring in nature but perhaps not severely constrained to physics, chemistry as well as biology alone.

The other three choices have no relation to a particular task. So the option given here is just the right one.

A projectile is shot from the edge of a cliff 80 m above ground level with an initial speed of 60 m/sec at an angle of 30° with the horizontal. Determine the time taken by the projectile to hit the ground below.

Answers

Answer:

8 seconds

Explanation:

Answer:

Explanation:

Going up

Time taken to reach maximum height= usin∅/g

=3 secs

Maximum height= H+[(usin∅)²/2g]

=80+[(60sin30)²/20]

=125 meters

Coming Down

Maximum height= ½gt²

125= ½(10)(t²)

t=5 secs

A rectangular conducting loop of wire is approximately half-way into a magnetic field B (out of the page) and is free to move. Suppose the magnetic field B begins to decrease rapidly in strength

Requried:
What happens to the loop?

1. The loop is pushed to the left, toward the magnetic field.
2. The loop doesn’t move.
3. The loop is pushed downward, towards the bottom of the page.
4. The loop will rotate.
5. The loop is pushed upward, towards the top of the page.
6. The loop is pushed to the right, away from the magnetic field

Answers

Answer:

. The loop is pushed to the right, away from the magnetic field

Explanation

This decrease in magnetic strength causes an opposing force that pushes the loop away from the field

If a transformer has 50 turns in the primary winding and 10 turns on the secondary winding, what is the reflected resistance in the primary if the secondary load resistance is 250 W?

Answers

Answer:

The reflected resistance in the primary winding is 6250 Ω

Explanation:

Given;

number of turns in the primary winding, [tex]N_P[/tex] = 50 turns

number of turns in the secondary winding, [tex]N_S[/tex] = 10 turns

the secondary load resistance, [tex]R_S[/tex] = 250 Ω

Determine the turns ratio;

[tex]K = \frac{N_P}{N_S} \\\\K = \frac{50}{10} \\\\K = 5[/tex]

Now, determine the reflected resistance in the primary winding;

[tex]\frac{R_P}{R_S} = K^2\\\\R_P = R_SK^2\\\\R_P = 250(5)^2\\\\R_P = 6250 \ Ohms[/tex]

Therefore, the reflected resistance in the primary winding is 6250 Ω

A solid block is attached to a spring scale. When the block is suspended in air, the scale reads 21.2 N; when it is completely immersed in water, the scale reads 18. 2 N. What are the volume and density of the block?

Answers

Answer:

7066kg/m³

Explanation:

The forces in these cases (air and water) are: Fa =mg =ρbVg Fw =(ρb −ρw)Vg where ρw = 1000 kg/m3 is density of water and ρb is density of the block and V is its density. We can find it from this two equations:

Fa /Fw = ρb / (ρb −ρw) ρb = ρw (Fa /Fa −Fw) =1000·(1* 21.2 /21.2 − 18.2)

= 7066kg/m³

Explanation:

Answer:

The volume of the block is 306 cm³

The density of the block is 7.07 g/cm³

Explanation:

Given;

weight of block in air, [tex]W_a[/tex] = 21.2 N

Weight of block in water, [tex]W_w[/tex] = 18.2 N

Mass of the block in air;

[tex]W_a = mg[/tex]

21.2 = m x 9.8

m = 21.2 / 9.8

m = 2.163 kg

mass of the block in water;

[tex]W_w = mg[/tex]

18.2 = m x 9.8

m = 18.2 / 9.8

m = 1.857 kg

Apply Archimedes principle

Mass of object in air  - mass of object in water = density of water   x  volume                  of object

2.163 kg - 1.857 kg = 1000 kg/m³ x Volume of block

0.306 kg = 1000 kg/m³ x Volume of block

Volume of the block = [tex]\frac{0.306 \ kg}{1000 \ kg/m^3}[/tex]

Volume of the block = 3.06 x 10⁻⁴ m³

Volume of the block = 306 cm³

Determine the density of the block

[tex]Density = \frac{mass}{volume} \\\\Density =\frac{2163 \ g}{306 \ cm^3} \\\\Density = 7.07 \ g/cm^3[/tex]

Two sources of light of wavelength 700 nm are 9 m away from a pinhole of diameter 1.2 mm. How far apart must the sources be for their diffraction patterns to be resolved by Rayleigh's criterion

Answers

Answer:

The distance is  [tex]D = 0.000712 \ m[/tex]

Explanation:

From the question we are told that

    The wavelength of  the  light source is  [tex]\lambda = 700 \ nm = 700 *10^{-9} \ m[/tex]

     The distance from a pin hole is  [tex]x = 9\ m[/tex]

       The  diameter of the pin  hole is  [tex]d = 1.2 \ mm = 0.0012 \ m[/tex]

     

Generally the distance which the light source need to be in order for their diffraction patterns to be resolved by Rayleigh's criterion is

mathematically represented as

              [tex]D = \frac{1.22 \lambda }{d }[/tex]

substituting values

             [tex]D = \frac{1.22 * 700 *10^{-9} }{ 0.0012 }[/tex]

             [tex]D = 0.000712 \ m[/tex]

Six automobiles are initially traveling at the indicated velocities. The automobiles have different masses and velocities. The drivers step on the brakes and all automobiles are brought to rest.Automobile 1: 500kg, 10m/sAutomobile 2: 2000kg, 5m/sAutomobile 3: 500kg, 20m/sAutomobile 4: 1000kg, 20m/sAutomobile 5: 1000kg, 10m/sAutomobile 6: 4000kg, 5m/sRequired:a. Rank these automobiles based on the magnitude of their momentum before the brakes are applied, from largest to smallest.b. Rank these automobiles based on the magnitude of the impulse needed to stop them, from largest to smallest.c. Rank the automobiles based on the magnitude of the force needed to stop them, from largest to smallest.

Answers

Answer:

A. largest: (4000 kg, 5 m/s; 1000 kg, 20 m/s)

medium: (2000 kg, 5 m/s; 500 kg, 20 m/s; 1000 kg, 10 m/s)

smallest: (500 kg, 10 m/s)

B. largest: (4000 kg, 5 m/s; 1000 kg, 20 m/s)

medium: (2000 kg, 5 m/s; 500 kg, 20 m/s; 1000 kg, 10 m/s)

smallest: (500 kg, 10 m/s)

C. You can't say anything about the forces required until we know about the time frames required for each one to stop. So If they all stopped in the same time interval, then the rankings are the same.

If you stood on a planet having a mass four times higher than Earth's mass, and a radius two times 70) lon longer than Earth's radius, you would weigh:________
A) four times more than you do on Earth.
B) two times less than you do on Earth.
C) the same as you do on Earth
D) two times more than you do on Earth.

Answers

CHECK COMPLETE QUESTION BELOW

you stood on a planet having a mass four times that of earth mass and a radius two times of earth radius , you would weigh?

A) four times more than you do on Earth.

B) two times less than you do on Earth.

C) the same as you do on Earth

D) two times more than you do on Earth

Answer:

OPTION C is correct

The same as you do on Earth

Explanation :

According to law of gravitation :

F=GMm/R^2......(a)

F= mg.....(b)

M= mass of earth

m = mass of the person

R = radius of the earth

From law of motion

Put equation b into equation a

mg=GMm/R^2

g=GMm/R^2

g=GM/R^2

We know from question a planet having a mass four times that of earth mass and a radius two times of earth radius if we substitute we have

m= 4M

r=(2R)^2=4R^2

g= G4M/4R^2

Then, 4in the denominator will cancel out the numerator we have

g= GM/R^2

Therefore, g remain the same

Two automobiles are equipped with the same singlefrequency horn. When one is at rest and the other is moving toward the first at 20 m/s , the driver at rest hears a beat frequency of 9.0 Hz.

Requried:
What is the frequency the horns emit?

Answers

Answer: f ≈ 8.5Hz

Explanation: The phenomenon known as Doppler Shift is characterized as a change in frequency when one observer is stationary and the source emitting the frequency is moving or when both observer and source are moving.

For a source moving and a stationary observer, to determine the frequency:

[tex]f_{0} = f_{s}.\frac{c}{c-v_{s}}[/tex]

where:

[tex]f_{0}[/tex] is frequency of observer;

[tex]f_{s}[/tex] is frequency of source;

c is the constant speed of sound c = 340m/s;

[tex]v_{s}[/tex] is velocity of source;

Rearraging for frequency of source:

[tex]f_{0} = f_{s}.\frac{c}{c-v_{s}}[/tex]

[tex]f_{s} = f_{0}.\frac{c-v_{s}}{c}[/tex]

Replacing and calculating:

[tex]f_{s} = 9.(\frac{340-20}{340})[/tex]

[tex]f_{s} = 9.(0.9412)[/tex]

[tex]f_{s} =[/tex] 8.5

Frequency the horns emit is 8.5Hz.

At what rate must Uranium 235 undergo fission by neutron bombardment to generate energy at a rate of 100 W (1 W

Answers

Complete Question

At what rate must Uranium 235 undergo fission by neutron bombardment to generate energy at a rate of 100 W (1 W = 1 J/s)? Assume each fission reaction releases 200 MeV of energy.

Answer

a. Approximately [tex]5*10^{10}[/tex] fissions per second.

b. Approximately [tex]6*10^{12 }[/tex]fissions per second.

c. Approximately [tex]4*10^{11}[/tex] fissions per second.

d. Approximately [tex]3*10^{12}[/tex] fissions per second.

e. Approximately[tex]3*10^{14}[/tex] fissions per second.

Answer:

The correct option is  d

Explanation:

From the question we are told that

       The energy released by each fission reaction [tex]E = 200 \ MeV = 200 *10^{6} * 1.60 *10^{-19} =3.2*10^{-11} \ J /fission[/tex]

Thus to generated  [tex]100 \ J/s[/tex] i.e  (100 W  ) the rate of fission is  

              [tex]k = \frac{100}{3.2 *10^{-11} }[/tex]

              [tex]k =3*10^{12} fission\ per \ second[/tex]

Can you come up with a mathematical relationship, based on your data that shows the relationship between distance from the charges and electric field strength?

Answers

Answer:

Explanation:

This question appears incomplete because of the absence of the data been talked about in the question. However, there is a general ruling here and it can be applied to the data at hand.

If an increase in the distance of charges (let's denote with "d") causes the electric field strength (let's denote with"E") to increase, then the mathematical representation can be illustrated as d ∝ E (meaning distance of charge is directly proportional to electric field strength).

But if an increase in the distance of the charges causes the electric field strength to decrease, then the mathematical representation can be illustrated as d ∝ 1/E (meaning distance of charge is inversely proportional to electric field strength).

A scatterplot can also be used to determine this. If there is a positive correlation (correlation value is greater than zero but less than or equal to 1) on the graph, then it is illustrated as "d ∝ E" BUT if there is a negative correlation (correlation value is less than zero but greater than or equal to -1), then it can be illustrated as "d ∝ 1/E".

Give an example of a fad diet that is not healthy and one that is healthy. Explain how you know the difference.

Answers

Answer:

 Good Diet: ! gallon of water a day, Fruits, Vegetables, White meats(Chicken), Don't eat past 3 PM.

Bad Diet: Pizza, Red meat, Baked goods, Eating at late hours.

Explanation: I know the difference because, When you drink water first thing in the morning it gets your metabolism running. Than means you can digest foods better, you want to feed your body good foods but you should not eat until you feel stuffed. You should eat until you are no longer starving. Than you should drink a cup of water in between meals. I know you should not eat past 3 pm because your body needs time to digest foods because you should never go to sleep with a full stomach. I know the difference between good food and bad food because when you eat healthy food and a balanced diet, your body will have more energy and you wont feel tired afterwards. Eating bad foods and food with artificial sugars will clump up in your kidneys, and your body will have small bursts of energy but you will feel lazy afterwards...Your body is supposed to stay energized from a healthy meal in order to give you the energy your body needs to exercise. If you feel droopy all the time and you don't want to do anything, than you are unhealthy.

Answer:

A vegetarian diet is an example of a good fad diet if you do it correctly. It can help you get lots of veggies and good nutrients from them while still following the non-meat diet you want. This can be effective and good for weight loss becasue you are still eating and getting all the good nutrients and calories from less fatty foods. 

Vegan diet (some can be successful but many people fail and do not do good that is why I choose this) The problem with this fad diet is that it can cause nutritional deficiencies and lead to a host of additional health problems, including negatively impacting hormonal health and metabolism. Many people also struggle to find healthy vegan food and end up eating bad and fatty foods instead. 

Explanation:

Got a 100

The place you get your hair cut has two nearly parallel mirrors 6.5 m apart. As you sit in the chair, your head is

Answers

Complete question is;

The place you get your hair cut has two nearly parallel mirrors 6.50 m apart. As you sit in the chair, your head is 3.00 m from the nearer mirror. Looking toward this mirror, you first see your face and then, farther away, the back of your head. (The mirrors need to be slightly nonparallel for you to be able to see the back of your head, but you can treat them as parallel in this problem.) How far away does the back of your head appear to be?

Answer:

13 m

Explanation:

We are given;

Distance between two nearly parallel mirrors; d = 6.5 m

Distance between the face and the nearer mirror; x = 3 m

Thus, the distance between the back-head and the mirror = 6.5 - 3 = 3.5m

Now, From the given values above and using the law of reflection, we can find the distance of the first reflection of the back of the head of the person in the rear mirror.

Thus;

Distance of the first reflection of the back of the head in the rear mirror from the object head is;

y' = 2y

y' = 2 × 3.5

y' = 7

The total distance of this image from the front mirror would be calculated as;

z = y' + x

z = 7 + 3

z = 10

Finally, the second reflection of this image will be 10 meters inside in the front mirror.

Thus, the total distance of the image of the back of the head in the front mirror from the person will be:

T.D = x + z

T.D = 3 + 10

T.D = 13m

What is the angle between a wire carrying an 8.40 A current and the 1.20 T field it is in, if 50.0 cm of the wire experiences a magnetic force of 2.55 N? ° (b) What is the force (in N) on the wire if it is rotated to make an angle of 90° with the field? N

Answers

Answer:

A. 30.38°

B 5.04N

Explanation:

Using

F= ILBsin theta

2 .55N= 8.4Ax 0.5mx 1.2T x sintheta

Theta = 30.38°

B. If theta is 90°

Then

F= 8.4Ax 0.5mx 1.2x sin 90°

F= 5.04N

You shine unpolarized light with intensity 52.0 W/m2 on an ideal polarizer, and then the light that emerges from this polarizer falls on a second ideal polarizer. The light that emerges from the second polarizer has intensity 15.0 W/m2. Find the intensity of the light that emerges from the first polarizer.

Answers

Answer:

The intensity of light from the first polarizer  is [tex]I_1 = 26 W/m^2[/tex]

Explanation:

  The intensity of the unpolarized light is  [tex]I_o = 52.0 \ W/m^2[/tex]

   

Generally the intensity of light that emerges from the first polarized light is

            [tex]I_1 = \frac{I_o}{2 }[/tex]

 substituting values

             [tex]I_1 = \frac{52. 0}{2 }[/tex]

             [tex]I_1 = 26 W/m^2[/tex]

Other Questions
Who is the King of Kuwait Katherine Johnson reached for the stars long before she helped send humans into space. Born on August 26, 1918 in West Virginia, Johnson had a gift for numbers. As Johnson later described, she spent her life countingcounting the steps she walked, the dishes she washed. Anything that could be counted, I did, she once said. School came easily for Johnson, and she completed eighth grade by the age of 10. After that, she couldnt continue learning locally because her county denied African American students access to secondary education. Johnsons father, Joshua, moved the family 120 miles away so she could attend high school. By 18, she graduated with honors from West Virginia State College, receiving degrees in mathematics and French. She then went on to teach these subjects at a public school. After teaching for many years, one job posting changed the arc of her life. The National Advisory Committee for Aeronautics (NACA) was looking to hire women to fill unique positions. The job title: Computer. Based at Langley Research Center, these human calculators checked the math done by NACAs male engineers and mathematicians. Johnsons sharp intellect and resourcefulness were quickly recognized at Langley; she was promoted after only two weeks. Nonetheless, Johnson faced barriers at the agency. At the time, many workplaces werent integrated, and Johnson and her African American colleagues were segregated within an area of Langley named West Computers. Regardless, she steadfastly asked questions and made her voice heard. In 1958, NACA began to focus more on space travel, and the agency was newly dubbed the National Aeronautics and Space Administration (NASA). Johnsons career flourished at NASA. In 1961, Johnson plotted astronaut Alan Shepards path into space. Then in 1962, Johnson helped astronaut John Glenn to be the first American to orbit the Earth. Even though NASA had started using electronic computers, Johnson was the one to double-check the machines calculations before blast-off. Additionally, Johnson contributed to Apollo 11s milestone 1969 moon landing. She also helped Apollo 13 return safely home after an equipment malfunction. Later in her career, Johnson worked on calculations for NASAs space shuttles and satellites. Even with such stellar contributions, many people in America didnt know Johnsons name until long after her retirement. In 2016, writer Margot Lee Shetterly published Hidden Figures, a chronicle of Johnson and two of her fellow mathematicians work at NASA. Later that year, shetterlys bestselling book was turned into a movie of the same name. Finally, the whole world saw the magnificent trajectory of Katherine Johnsons career. Read the excerpt. Even with such stellar contributions, many people in America didnt know Johnsons name until long after her retirement. In 2016, writer Margot Lee Shetterly published Hidden Figures, a chronicle of Johnson and two of her fellow mathematicians work at NASA. Choose the two synonyms that have the same meaning as the word figures as its used in the title of Shetterlys book. Choose 2 answers: (Choice A) A definitions (Choice B) B answers (Choice C) C numbers (Choice D) D questions (Choice E) E shapes (Choice F) F people In the rational choice decision process model, which of the following immediately follows the step where possible choices have been discovered or developed? a. Discover possible choices. b. Select the choice with the highest value. c. Implement the selected choice d. Evaluate the selected choice. The ancient Greek Eratosthenes found that the Sun casts different lengths of shadow at different points on Earth. There were no shadows at midday in Aswan as the Sun was directly overhead. 800 kilometers north, in Alexandria, shadow lengths were found to show the Sun at 7.2 degrees from overhead at midday. Use these measurements to calculate the radius of Earth. Explain why only the lone pairs on the central atom are taken into consideration when predicting molecular shape Geoscientists use ___________ to explore the deep layers of the Earth that humans can not yet dig down into. Geoscientists obtain seismic data from: (Mark All that Apply).the tides human-induced explosions naturally occurring earthquakes the coriolis force How are Earthquakes Measured? Magnitude Scale Richter Scale Fujita Scale Saffir-Simpson Scale The outer brittle shell of the Earth is the ______ that forms the "skin" of the lithosphere. mantle outer core inner core crustWhat is the deepest that humans have been able to dig into Earth? 7.6 miles 16.2 miles 1.7 miles 170.2 miles Streams of charged particles ejected from the sun are called ____________. electromagnetic storms magnetosphere radio waves solar wind A baseball has a mass of 135 grams and a softball has a mass of 270 grams. In which of the following situations would they have the same momentum? The baseball and softball are thrown at the same speed in the same direction. Determine if the matrix below is invertible. Use as few calculations as possible. Justify your answer. [Start 4 By 4 Matrix 1st Row 1st Column 4 2nd Column 5 3rd Column 7 4st Column 5 2nd Row 1st Column 0 2nd Column 1 3rd Column 4 4st Column 6 3rd Row 1st Column 0 2nd Column 0 3rd Column 3 4st Column 8 4st Row 1st Column 0 2nd Column 0 3rd Column 0 4st Column 1 EndMatrix ] What steps are needed for word to create an index A baseball (m=145g) traveling 35 m/s moves a fielder's glove backward 23 cm when the ball is caught. What was the average force exerted by the ball on the glove? Write the equation of the line which passesthrough the points (4,2) and (-3, 1) Why is the continental divide important US history A sequence starts at 200 and 30 is subtracted each time . 200 , 170, 140 ...What are the first two numbers in the sequence that are less than zero ? light bulb is connected to a 110-V source. What is the resistance of this bulb if it is a 100-W bulb 1. Find the area of a triangle (PLEASE ONLY in CM) 2. Seven squared equals seven times ......... At what minimum angle will you get total internal reflection of light traveling in diamond and reflected from ethanol? A professor, with dumbbells in his hands and holding his arms out, is spinning on a turntable with an angular velocity. What happens after he pulls his arms inwards Use the motion map to answer the question.Which scenario could be represented by the motionmap?O A car speeds up to merge onto the freeway andthen continues at a constant velocityO A car speeds up to pass a truck, then slows downto a constant velocity.O A car slows to stop at a stop sign. Once traffic isclear, the car speeds up.O A car slows to makes a U-turn, then continues inthe opposite direction. We need to understand the past so that we might better assess the: challenges of the past and the present challenges of the present and the future opportunities of the present and the future opportunities of the past and the present ASAP How can I divide decimals and fin the correct quotient and remainder.?