Answer:
A
Explanation:
Consider a question you may not have considered before. Suppose you have a mole of sodium in a container that contains nothing that it will react with. A mole of anything is 6.02 * 10^23 (in this case atoms).
Suppose that every one of those atoms has contributed 1 electron to something.
Do you think it would be safe to touch the container knowing that there are 6.02 * 10^23 positive charges all eager to get another electron, because they don't like repelling each other.
Safe or not? I'll give you a hint. A lightning bolt does not contain anywhere near 6.02*10^23 charges. No where near.
So -- since you never get a shock from just touching anything, There must not be electrons or ions present.
The answer is A
When your vehicle turns a corner, the tracks made by the rear tires are always: a) Outside of those made by your front tires b) Inside of those made by your front tires c) On top of those made by your front tires d) None are correct
Answer:
I think it's D
Explanation:
because I have seen the tracks of the tires
Capacitance (C) is measured in farads, where 1 farad is equivalent to 1 coulomb per volt. Resistance (R) is measured in ohms, and 1 ohm is equal to 1 volt per ampère. The coulomb is defined as the amount of charge passing when a current of 1 ampère flows for 1 second. What is the unit of RC expressed in its simplest form?
When fundamental units are combined, they result in derived units. RC (which means Resistance Capacitance) is a derived unit and its unit in the simplest form is Coulomb per Ampere (C/A)
Given that:
Capacitance (C) [tex]\to[/tex] Farads (f)
and
[tex]1f = 1\frac CV[/tex] ----- 1 farad = 1 capacitance per volt
Resistance (R) [tex]\to[/tex] Ohms [tex]\Omega[/tex]
[tex]1 \Omega = 1\frac{V}{A}[/tex]
The unit of RC is the product of the unit of R by the unit of C.
i.e.
[tex]RC = 1f \times 1\Omega[/tex]
Substitute [tex]1f = 1\frac CV[/tex]
[tex]RC = 1\frac CV \times 1\Omega[/tex]
Substitute [tex]1 \Omega = 1\frac{V}{A}[/tex]
[tex]RC = 1\frac CV \times 1\frac VA[/tex]
Cancel out volts (V)
[tex]RC = 1\frac CA[/tex]
[tex]\frac CA[/tex] means Coulomb per Ampere
Hence, the unit of RC is Coulomb per Ampere.
Read more about units at:
https://brainly.com/question/10167613
In 'coin on card' experiment a smooth card is used.
Answer:
In coin card experiment smooth card is used so that the card can slide easily from glass
How does the construction of dams positively affect natural resources?
by providing water for irrigation and restoring trees to areas where forests once existed
by creating reservoirs, preventing flooding, and renewing destroyed ecosystems
by preventing flooding, creating reservoirs, and providing water for irrigation
by renewing destroyed ecosystems and restoring trees to areas where forest once existed
Other person is incorrect, I did the test on edg.
Answer:
A. by providing water for irrigation and restoring trees to areas where forests once existed
The construction of dams positively affect natural resources by providing water for irrigation.
What is natural resources?Natural resources serves as materials thst is found in nature which are used by humans. These natural substances are soil, water.
Therefore, building of dams can help irrigation by using water which is a natural resources.
Learn more about natural resources at;
https://brainly.com/question/24623157
Calculate surface tension of an enlarged radius of 4cm to 6cm and amount of work necessary for enlargement was 1.5×10^-4 joules
Answer:
[tex]T=7.5*10^{-5}[/tex]
Explanation:
From the question we are told that:
Radius [tex]r=2cm[/tex]
Work done [tex]W=1.5×10^-4 joules[/tex]
Generally the equation for Work done is mathematically given by
[tex]W=T.dA[/tex]
Therefore
[tex]T=\frac{W}{dr}[/tex]
[tex]T=\frac{1.5*10^{-4}}{2}[/tex]
[tex]T=7.5*10^{-5}[/tex]
What is meant by measurement? l
Answer:
The action of measuring the size, length, or amount of something, as established is called measurement.
Explanation:
“Measurement” is the act of determining a target's size, length, weight, capacity, or other aspect. ... To use measurement tools as necessary. It is also appropriate to say that measurement is done by a worker using a measurement system, and instrumentation is done by a technician.
