Answer:
Explanation:
When plastic balloon is rubbed with wool , charges are created on both balloon and silk in equal amount . Rubber balloon will acquire negative charge and silk will acquire positive charge .
Now when balloon is brought near a wall , there is induction of charge on the wall due to charge on the balloon . On the near surface of wall positive charge is produced and on the surface deep inside the wall negative charge is produced . The charge deep inside goes inside the earth but the positive charge near the surface of wall can not escape . It remains trapped by negative charge on the balloon .
hence there is mutual attraction between balloon and surface of wall is just like attraction between opposite charges . But once the ballon due to mutual attraction comes in contact with the wall , the charge on balloon and on wall neutralises each other and hence after some time the balloon falls off from the wall on the ground . It does not remain attracted to wall for ever . It happens due to neutralisation of charges on balloon and wall .
PLEASE HELP FAST Five-gram samples of brick and glass are at room temperature. Both samples receive equal amounts of energy due to heat flow. The specific heat capacity of brick is 0.22 cal/g°C and the specific heat capacity of glass is 0.22 cal/g°C. Which of the following statements is true? 1.The temperature of each sample will increase by the same amount. 2.The temperature of each sample will decrease by the same amount. 3.The brick will get hotter than the glass. 4.The glass will get hotter than the brick.
Answer:
1.The temperature of each sample will increase by the same amount
Explanation:
This is because, since their specific heat capacities are the same and we have the same mass of each substance, and the same amount of energy due to heat flow is supplied to both the glass and brick at room temperature, their temperatures would thereby increase by the same amount.
This is shown by the calculation below
Q = mcΔT
ΔT = Q/mc where ΔT = temperature change, Q = amount of heat, m = mass of substance and c = specific heat capacity of substance.
Since Q, m and c are the same for both substances, thus ΔT will be the same.
So, the temperature of each sample will increase by the same amount
With the same block-spring system from above, imagine doubling the displacement of the block to start the motion. By what factor would the following change?
A. Kinetic energy when passing through the equilibrium position.
B. Speed when passing through the equilibrium position.
Answer:
A) K / K₀ = 4 b) v / v₀ = 4
Explanation:
A) For this exercise we can use the conservation of mechanical energy
in the problem it indicates that the displacement was doubled (x = 2xo)
starting point. At the position of maximum displacement
Em₀ = Ke = ½ k (2x₀)²
final point. In the equilibrium position
[tex]Em_{f}[/tex] = K = ½ m v²
Em₀ = Em_{f}
½ k 4 x₀² = K
(½ K x₀²) = K₀
K = 4 K₀
K / K₀ = 4
B) the speed value
½ k 4 x₀² = ½ m v²
v = 4 (k / m) x₀
if we call
v₀ = k / m x₀
v = 4 v₀
v / v₀ = 4
A bungee cord with a spring constant of 800 StartFraction N over m EndFraction stretches 6 meters at its greatest displacement. How much elastic potential energy does the bungee cord have? The bungee cord has J of elastic potential energy.
Explanation:
EE = ½ kx²
EE = ½ (800 N/m) (6 m)²
EE = 14,400 J
Answer:
14,400 J
Explanation:
Its the answer
A metal sphere A of radius a is charged to potential V. What will be its potential if it is enclosed by a spherical conducting shell B of radius b and the two are connected by a wire?
Answer:
The potential will be Va/b
Explanation:
So Let sphere A charged Q to potential V.
so, V= KQ/a. ....(1
Thus, spherical shell B is connected to the sphere A by a wire, so all charge always reside on the outer surface.
therefore, potential will be ,
V ′ = KQ/b = Va/b... That is from .....(1), KQ=Va]
The molecules in Tyler are composed of carbon and other atoms that share one or more electrons between two atoms, forming what is known as a(n) _____ bond.
Answer:
covalent
Explanation:
covalent bonds share electrons
A single-slit diffraction pattern is formed on a distant screen. Assuming the angles involved are small, by what factor will the width of the central bright spot on the screen change if the slit width is doubled
Answer:
y ’= y / 2
thus when the slit width is doubled the pattern width is halved
Explanation:
The diffraction of a slit is given by the expressions
a sin θ = m λ
where a is the width of the slit, λ is the wavelength and m is an integer that determines the order of diffraction.
sin θ = m λ / a
If this equation
a ’= 2 a
we substitute
2 a sin θ'= m λ
sin θ'= (m λ / a) 1/2
sin θ ’= sin θ / 2
We can use trigonometry to find the width
tan θ = y / L
as the angle is small
tan θ = sin θ / cos θ = sin θ
sin θ = y / L
we substitute
y ’/ L = y/L 1/2
y ’= y / 2
thus when the slit width is doubled the pattern width is halved
A girl is sitting on the edge of a pier with her legs dangling over the water. Her soles are 80.0 cm above the surface of the water. A boy in the water looks up at her feet and wants to touch them with a reed. (nwater =1.333). He will see her soles as being:____
a. right at the water surface.
b. 53.3 cm above the water surface.
c. exactly 80.0 cm above the water surface.
d. 107 cm above the water surface.
e. an infinite distance above the water surface.
Answer:
d. 107 cm above the water surface.
Explanation:
The refractive index of water and air = 1.333
The real height of the girl's sole above water = 80.0 cm
From the water, the apparent height of the girl's sole will be higher than it really is in reality by a factor that is the refractive index.
The boy in the water will therefore see her feet as being
80.0 cm x 1.333 = 106.64 cm above the water
That is approximately 107 cm above the water
At what speed (in m/s) will a proton move in a circular path of the same radius as an electron that travels at 7.45 ✕ 106 m/s perpendicular to the Earth's magnetic field at an altitude where the field strength is 1.10 ✕ 10−5 T
Answer:
The speed of the proton is 4059.39 m/s
Explanation:
The centripetal force on the particle is given by;
[tex]F = \frac{mv^2}{r}[/tex]
The magnetic force on the particle is given by;
[tex]F = qvB[/tex]
The centripetal force on the particle must equal the magnetic force on the particle, for the particle to remain in the circular path.
[tex]\frac{mv^2}{r} = qvB\\\\r = \frac{mv^2}{qvB} \\\\r = \frac{mv}{qB}[/tex]
where;
r is the radius of the circular path moved by both electron and proton;
⇒For electron;
[tex]r = \frac{(9.1*10^{-31})(7.45*10^6)}{(1.602*10^{-19})(1.1*10^{-5})}\\\\r = 3.847 \ m[/tex]
⇒For proton
The speed of the proton is given by;
[tex]r = \frac{mv}{qB}\\\\mv = qBr\\\\v = \frac{qBr}{m} \\\\v = \frac{(1.602*10^{-19})(1.1*10^{-5})(3.847)}{1.67*10^{-27}} \\\\v = 4059.39 \ m/s[/tex]
Therefore, the speed of the proton is 4059.39 m/s
A toroidal solenoid with 400 turns of wire and a mean radius of 6.0 cm carries a current of 0.25 A. The relative permeability of the core is 80.
(a) What is the magnetic field in the core?
(b) What part of the magnetic field is due to atomic currents?
Answer:
A) 0.0267 T
B) 0.0263 T
Explanation:
Given that
The number of turns, N = 400
Radius of the wire, r = 6 cm = 0.06 m
Current in the wire, I = 0.25 A
Relative permeability, K(m) = 80
See the attached picture for the calculation
A car moving at 36 m/s passes a stationary police car whose siren has a frequency of 500 Hz. What is the change in the frequency (in Hz) heard by an observer in the moving car as he passes the police car? (The speed of sound in air is 343 m/s.)
Answer:
Change in the frequency (in Hz) = 104.96 Hz
Explanation:
Given:
Speed of sound in air (v) = 343 m/s
Speed of car (v1) 36 m/s
Frequency(f) = 500 Hz
Find:
Change in the frequency (in Hz)
Computation:
Frequency hear by the observer(before)(f1) = [f(v+v1)] / v
Frequency hear by the observer(f1) = [500(343+36)] / 343
Frequency hear by the observer(f1) = 552.48 Hz
Frequency hear by the observer(after)(f2) = [f(v-v1)] / v
Frequency hear by the observer(f2) = [500(343-36)] / 343
Frequency hear by the observer(f2) = 447.52 Hz
Change in the frequency (in Hz) = f1 - f2
Change in the frequency (in Hz) = 552.48 Hz - 447.52 Hz
Change in the frequency (in Hz) = 104.96 Hz
a car moves for 10 minutes and travels 5,280 meters .What is the average speed of the car?
Answer:use the formular distance over time i.e distance/time. Make sure to convert the distance from metres to kilometers and time from minutes to hours .
Explanation:
The average speed of the car is 31,680 meters per hour.
To calculate the average speed of the car, you need to divide the total distance traveled by the time it took to travel that distance.
Given:
Time taken (t) = 10 minutes = 10 minutes × (1 hour / 60 minutes) = 10/60 hours = 1/6 hours
Distance traveled (d) = 5,280 meters
Average Speed (v) = Distance (d) / Time (t)
Average Speed (v) = 5280 meters / (1/6) hours
To simplify, when you divide by a fraction, it's equivalent to multiplying by its reciprocal:
Average Speed (v) = 5280 meters × (6/1) hours
Average Speed (v) = 31,680 meters per hour
Hence, the average speed of the car is 31,680 meters per hour.
To know more about average speed here
https://brainly.com/question/17661499
#SPJ2
A small helium-neon laser emits red visible light with a power of 5.40 mW in a beam of diameter 2.30 mm.
Required:
a. What is the amplitude of the electric field of the light? Express your answer with the appropriate units.
b. What is the amplitude of the magnetic field of the light?
c. What is the average energy density associated with the electric field? Express your answer with the appropriate units.
d. What is the average energy density associated with the magnetic field? Express your answer with the appropriate units.
E) What is the total energy contained in a 1.00-m length of the beam? Express your answer with the appropriate units.
Answer:
A. 990v/m
B.330x10^-8T
C.2.19x10^-6J/m³
D.1.45x10^-11J
Explanation:
See attached file
An electrostatic paint sprayer contains a metal sphere at an electric potential of 25.0 kV with respect to an electrically grounded object. Positively charged paint droplets are repelled away from the paint sprayer's positively charged sphere and towards the grounded object. What charge must a 0.168-mg drop of paint have so that it will arrive at the object with a speed of 18.8 m/s
Answer:
The charge is [tex]Q = 2.177 *10^{-9} \ C[/tex]
Explanation:
From the question we are told that
The electric potential is [tex]V = 25.0 \ kV = 25.0 *10^{3}\ V[/tex]
The mass of the drop is [tex]m = 0.168 \ m g = 0.168 *10^{-3} \ g = 0.168 *10^{-6}\ kg[/tex]
The speed is [tex]v = 18.8 \ m/s[/tex]
Generally the charge on the paint drop due to the electric potential which will give it the speed stated in the question is mathematically represented as
[tex]Q = \frac{m v^2 }{ 2 * V }[/tex]
Substituting values
[tex]Q = \frac{0.168 *10^{-6} (18)^2 }{ 2 * 25*10^3 }[/tex]
[tex]Q = 2.177 *10^{-9} \ C[/tex]
Two blocks A and B have a weight of 11 lb and 5 lb , respectively. They are resting on the incline for which the coefficients of static friction are μA = 0.16 and μB = 0.23. Determine the incline angle θ for which both blocks begin to slide. Also find the required stretch or compression in the connecting spring for this to occur. The spring has a stiffness of k = 2.1 lb/ft .
Answer:
[tex]\theta=10.20^{\circ}[/tex]
[tex]\Delta l=0.10 ft[/tex]
Explanation:
First of all, we analyze the system of blocks before starting to move.
[tex]\Sum F_{x}=P_{A}sin(\theta)+P_{B}sin(\theta)-F_{fA}-F_{fB}=0[/tex]
[tex]\Sum F_{x}=11sin(\theta)+5sin(\theta)-0.16N_{A}-0.23N_{B}=0[/tex]
[tex]11sin(\theta)+5sin(\theta)-0.16P_{A}cos(\theta)-0.23P_{B}cos(\theta)=0[/tex]
[tex]11sin(\theta)+5sin(\theta)-0.16*11cos(\theta)-0.23*5cos(\theta)=0[/tex]
[tex]11sin(\theta)+5sin(\theta)-0.16*11cos(\theta)-0.23*5cos(\theta)=0[/tex]
[tex]16sin(\theta)-2.91cos(\theta)=0[/tex]
[tex]tan(\theta)=0.18[/tex]
[tex]\theta=arctan(0.18)[/tex]
[tex]\theta=10.20^{\circ}[/tex]
Hence, the incline angle θ for which both blocks begin to slide is 10.20°.
Now, if we do a free body diagram of block A we have that after the block moves, the spring force must be taken into account.
[tex]P_{A}sin(\theta)-F_{fA}-F_{spring}=0[/tex]
Where:
[tex]F_{spring} = k\Delta l=2.1\Delta l[/tex]
[tex]P_{A}sin(\theta)-0.16*11cos(\theta)-2.1\Delta l=0[/tex]
[tex]\Delta l=\frac{11sin(\theta)-0.16*11cos(\theta)}{2.1}[/tex]
[tex]\Delta l=0.10 ft[/tex]
Therefore, the required stretch or compression in the connecting spring is 0.10 ft.
I hope it helps you!
(a) The inclined angle for which both blocks begin to slide is 10.3⁰.
(b) The compression of the spring is 0.22 ft.
The given parameters;
mass of block A, = 11 lbmass of block B, = 5 lbcoefficient of static friction for A, = 0.16coefficient of static friction for B, = 0.23 spring constant, k = 2.1 lb/ftThe normal force on block A and B:
[tex]F_n_A = m_Agcos \ \theta\\\\F_n_B = m_Bgcos \ \theta[/tex]
The frictional force on block A and B:
[tex]F_f_A = \mu_s_AF_n_A \\\\F_f_B = \mu_s_BF_n_A[/tex]
The net force on the blocks when they starts sliding;
[tex](m_Ag sin \theta+ m_Bgsin\theta) - (F_f_A + F_f_B) = 0\\\\m_Ag sin \theta+ m_Bgsin\theta = F_f_A + F_f_B\\\\m_Ag sin \theta+ m_Bgsin\theta = \mu_Am_Agcos\theta \ + \ \mu_Bm_Bgcos\theta\\\\gsin\theta(m_A + m_B) = gcos\theta (\mu_Am_A + \mu_Bm_B)\\\\\frac{sin\theta}{cos \theta} = \frac{\mu_Am_A\ + \ \mu_Bm_B}{m_A\ + \ m_B} \\\\tan\theta = \frac{(0.16\times 11) \ + \ (0.23 \times 5)}{11 + 5} \\\\tan\theta = 0.1819\\\\\theta = tan^{-1}(0.1819)\\\\\theta = 10.3 \ ^0[/tex]
The change in the energy of the blocks is the work done in compressing the spring;
[tex]\Delta E = W\\\\F_A (sin \theta )d- \mu F_n d= \frac{1}{2} kd^2\\\\F_A sin\theta \ - \ \mu F_A cos\theta = \frac{1}{2} kd\\\\d = \frac{2F_A(sin\theta - \mu cos \theta) }{k} \\\\d = \frac{2\times 11(sin \ 10.3\ - \ 0.16\times cos \ 10.3) }{2.1} \\\\d = 0.22 \ ft[/tex]
Learn more here:https://brainly.com/question/16892315
Equipotential lines are lines with equal electric potential (for example, all the points with an electric potential of 5.0 V). Using the plot tool that comes with voltmeter (pencil icon) make two equipotential lines at r = 0.5 m and r = 1.5 m. Enable electric field vectors in the simulation. Put an electric field sensor at different points on the equipotential line and note the direction of the electric field vector. What can you conclude about the direction of the electric field vector in relation to the equipotential lines?
The direction for each field vector is perpendicular to equipotential lines.
Take a snapshot of the simulation showing equipotential lines and paste to a word document.
....................
The advantage of a hydraulic lever is A : it transforms a small force acting over a large distance into a large force acting over a small distance. B : it transforms a small force acting over a small distance into a large force acting over a large distance. C : it allows you to exert a larger force with less work. D : it transforms a large force acting over a large distance into a small force acting over a small distance. E : it transforms a large force acting over a small distance into a small force acting over a large distance.
Answer:
A) it transforms a small force acting over a large distance into a large force acting over a small distance.
Explanation:
The hydraulic lever works based on Pascal's law of transmission of pressure through a fluid. In the hydraulic lever, the pressure transmitted is the same.
Pressure transmitted P = F/A
where F is the force applied
and A is the area over which the force is applied.
This pressure can be manipulated on the input end as a small force applied over a small area, and then be transmitted to the output end as a large force over a large area.
F/A = f/a
where the left side of the equation is for the output, and the right side is for the input.
The volume of the displaced fluid will be the same on both ends of the hydraulic lever. Since we know that
volume V = (area A) x (distance d)
this means that the the piston on the input smaller area of the hydraulic lever will travel a greater distance, while the piston on the larger output area of the lever will travel a small distance.
From all these, we can see that the advantage of a hydraulic lever is that it transforms a small force acting over a large distance into a large force acting over a small distance.
A fan rotating with an initial angular velocity of 1500 rev/min is switched off. In 2.5 seconds, the angular velocity decreases to 400 rev/min. Assuming the angular acceleration is constant, answer the following questions.
How many revolutions does the blade undergo during this time?
A) 10
B) 20
C) 100
D) 125
E) 1200
Answer:
The blade undergoes 40 revolutions, so neither of the given options is correct!
Explanation:
The revolutions can be found using the following equation:
[tex]\theta_{f} = \theta_{i} + \omega_{i}*t + \frac{1}{2}\alpha*t^{2}[/tex]
Where:
α is the angular acceleration
t is the time = 2.5 s
[tex]\omega_{i}[/tex] is the initial angular velocity = 1500 rev/min
First, we need to find the angular acceleration:
[tex] \alpha = \frac{\omega_{f} - \omega_{i}}{t} = \frac{400 rev/min*2\pi rad*1 min/60 s - 1500 rev/min *2\pi rad*1 min/60 s}{2.5 s} = -46.08 rad/s^{2} [/tex]
Now, the revolutions that the blade undergo are:
[tex]\theta_{f} - \theta_{i} = \omega_{i}*t + \frac{1}{2}\alpha*t^{2}[/tex]
[tex]\Delta \theta = 1500 rev/min *2\pi rad*1 min/60 s*2.5 s - \frac{1}{2}*(46.08 rad/s^{2})*(2.5)^{2} = 248.7 rad = 39.9 rev[/tex]
Therefore, the blade undergoes 40 revolutions, so neither of the given options is correct!
I hope it helps you!
A semi-circular loop consisting of one turn of wire is place in the x-y plane. A constant magnetic field B=1.7T points along the negative z-axis(into the page), and a current I=0.7A flows counterclockwisefrom the positive z-axis. The net magnetic force on the circular section of the loop points in what direction? What is the net magnetice force on the circular section of the loop?
Answer:
The direction of net magnetic force on the circular section of the loop is in the positive y-axis
The net magnetic force on the circular section of the loop is 3.74 N
Explanation:
The magnetic field strength [tex]B[/tex] = 1.7 T
the current [tex]I[/tex] = 0.7 A
The diameter of the loop = 2 m
the length of the circular section of the semi-circular loop [tex]l[/tex] = πd/2
==> [tex]l[/tex] = (3.142 x 2)/2 = 3.142 m
The force on the semi-circular is given as
F = [tex]BIl[/tex] sin ∅
but the loop is perpendicular to the field, therefore
sin ∅ = sin 90° = 1
F = 1.7 x 0.7 x 3.142 x 1 = 3.74 N
The right hand rule states that "if the fingers of the right hand are held parallel to each other in the direction of the magnetic field, and the thumb is held at right angle to the other fingers in the direction of the flow of current. The palm will push in the direction of the magnetic force on the conductor".
According to the right hand rule, the direction of net magnetic force on the circular section of the loop is in the positive y-axis
Two football teams, the Raiders and the 49ers are engaged in a tug-of-war. The Raiders are pulling with a force of 5000N. Which of the following is an accurate statement?
A. The tension in the rope depends on whether or not the teams are in equilibrium.
B. The 49ers are pulling with a force of more than 5000N because of course they’d be winning.
C. The 49ers are pulling with a force of 5000N.
D. The tension in the rope is 10,000N.
E. None of these statements are true.
Answer:
E. None of these statements are true.
Explanation:
We can't say the exact or approximate amount of tension on the rope, since we do know for sure from the statement who is winning.
for A, the tension on the rope does not depend on if both teams pull are in equilibrium.
for B, the 49ers would be pulling with a force more than 5000 N, if they were winning. The problem is that we can't say with all confidence that they'd be winning.
for C, we don't know how much tension exists on the rope, and its direction, so we can't work out how much tension the 49ers are pulling the rope with.
for D, just as for C above, we can't work out how much tension there is on the rope, since we do not know how much force the 49ers are pulling with.
we go with option E.
A Cannonball is shot at an angle of 35.0 degrees and is in flight for 11.0 seconds before hitting the ground at the same height from which it was shot.
A. What is the magnitude of the inital velocity?B. What was the maximum height reached by the cannonball?C. How far, horizontally, did it travel?
Answer:
Explanation:
According to Equations of Projectile motion :
[tex]Time\ of\ Flight = \frac{2vsin(x)}{g}[/tex]
vsin(x) = 11 * 9.8 / 2 = 53.9 m/sec
(A) v (Initial velocity) = 11 * 9.8 / 2 * sin(35) = 94.56 m/sec
[tex]Maximum Height = \frac{(vsinx)^{2} }{2g}[/tex]
(B) Maximum Height = 53.9 * 53.9 / 2 * 9.8 = 142.2 m
[tex]Horizontal Range = vcosx * t[/tex]
(C) Horizontal Range = 94.56 * 0.81 * 11 = 842.52 m
A merry-go-round spins freely when Diego moves quickly to the center along a radius of the merry-go-round. As he does this, it is true to say that
Answer:
A) the moment of inertia of the system decreases and the angular speed increases.
Explanation:
The complete question is
A merry-go-round spins freely when Diego moves quickly to the center along a radius of the merry-go-round. As he does this, It is true to say that
A) the moment of inertia of the system decreases and the angular speed increases.
B) the moment of inertia of the system decreases and the angular speed decreases.
C) the moment of inertia of the system decreases and the angular speed remains the same.
D) the moment of inertia of the system increases and the angular speed increases.
E) the moment of inertia of the system increases and the angular speed decreases
In angular momentum conservation, the initial angular momentum of the system is conserved, and is equal to the final angular momentum of the system. The equation of this angular momentum conservation is given as
[tex]I_{1} w_{1} = I_{2} w_{2}[/tex] ....1
where [tex]I_{1}[/tex] and [tex]I_{2}[/tex] are the initial and final moment of inertia respectively.
and [tex]w_{1}[/tex] and [tex]w_{2}[/tex] are the initial and final angular speed respectively.
Also, we know that the moment of inertia of a rotating body is given as
[tex]I = mr^{2}[/tex] ....2
where [tex]m[/tex] is the mass of the rotating body,
and [tex]r[/tex] is the radius of the rotating body from its center.
We can see from equation 2 that decreasing the radius of rotation of the body will decrease the moment of inertia of the body.
From equation 1, we see that in order for the angular momentum to be conserved, the decrease from [tex]I_{1}[/tex] to [tex]I_{2}[/tex] will cause the angular speed of the system to increase from [tex]w_{1}[/tex] to [tex]w_{2}[/tex] .
From this we can clearly see that reducing the radius of rotation will decrease the moment of inertia, and increase the angular speed.
A brick weighs 50.0 N, and measures 30.0 cm × 10.0 cm × 4.00 cm. What is the maximum pressure it can exert on a horizontal surface due to its weight?
Answer:
Pressure, P = 1250 Pa
Explanation:
Given that,
Weight of a brick, F = 50 N
Dimension of the brick is 30.0 cm × 10.0 cm × 4.00 cm
We need to find the maximum pressure it can exert on a horizontal surface due to its weight. Pressure is equal to the force acting per unit area. Pressure exerted is inversely proportional to the area of cross section. So, we need to minimize area. Taking to smaller dimensions.
A = 40 cm × 10 cm = 400 cm² = 0.04 m²
So,
Pressure,
[tex]P=\dfrac{50\ N}{0.04\ m^2}\\\\P=1250\ Pa[/tex]
So, the maximum pressure of 1250 Pa it can exert on a horizontal surface.
The maximum pressure it can exert on a horizontal surface due to its weight will be 1250 Pascal.
What is pressure?The force applied perpendicular to the surface of an item per unit area across which that force is spread is known as pressure. It is denoted by P.
The given data in the problem is;
W is the weight of a brick = 50 N
The dimension of the brick = 30.0 cm × 10.0 cm × 4.00 cm
A is the area,
The area is found as;
A=40 cm × 10 cm = 400 cm² = 0.04 m²
The pressure is the ratio of the force and area
[tex]\rm P = \frac{F}{A} \\\\ \rm P = \frac{50}{0.04} \\\\ \rm P =1250 \ Pascal[/tex]
Hence the maximum pressure it can exert on a horizontal surface due to its weight will be 1250 Pascal.
To learn more about the pressure refer to the link;
https://brainly.com/question/356585
The difference between a DC and an AC generator is that
a. the DC generator has one unbroken slip ring.
b. the AC generator has one unbroken slip ring
c. the DC generator has one slip ring splitin two halves.
d. the AC generator has one slip ring split in two halves.
e The DC generator has twounbroken sip rings
Answer:
The AC generator has one unbroken slip ring
Explanation:
In physics, the application of electromagnetic induction can be seen in generators and dynamos. Electromagnetic induction is the process of generating electricity using magnets. It found applications in generators and the types of generator they found application is in AC and DC generator.
An AC generator is also called a Dynamo. A DC generator contains what is called a SPLIT RING fixed to the end of the coil which can be separated and coupled back according to the name "split". An AC generator also called a Dynamo makes use of a SLIP ring which cannot be divided into two. It comes as an entity. The presence of this rings is what differentiates a DC generator from an AC generator.
We can replace split rings with slip rings when converting a DC generator to an AC generator and vice versa.
It can therefore be concluded that the difference between a DC and an AC generator is that the AC generator has one unbroken slip ring.
An electron moving in the direction of the +x-axis enters a magnetic field. If the electron experiences a magnetic deflection in the -y direction, the direction of the magnetic field in this region points in the direction of the:______
Answer:
-z axis
Explanation:
According to the left hand rule for an electron in a magnetic field, hold the thumb of the left hand at a right angle to the rest of the fingers, and the rest of the fingers parallel to one another. If the thumb represents the motion of the electron, and the other fingers represent the direction of the field, then the palm will push in the direction of the force on the electron. In this case, the left hand will be held out with the thumb pointing to the right (+x axis), and the palm facing your body (-y axis). The magnetic field indicated by the other fingers will point down in the the -z axis.
The earth has a vertical electric field at the surface,pointing down, that averages 102 N/C. This field is maintained by various atmosphericprocesses, including lightning.
What is the excess charge on the surface of the earth? inC
Answer:
[tex]q = -461532.5 \ C[/tex]
Explanation:
From the question we are told that
The electric filed is [tex]E = 102 \ N/C[/tex]
Generally according to Gauss law
=> [tex]E A = \frac{q}{\epsilon_o }[/tex]
Given that the electric field is pointing downward , the equation become
[tex]- E A = \frac{q}{\epsilon_o }[/tex]
Here [tex]q[/tex] is the excess charge on the surface of the earth
[tex]A[/tex] is the surface area of the of the earth which is mathematically represented as
[tex]A = 4\pi r^2[/tex]
Where r is the radius of the earth which has a value [tex]r = 6.3781*10^6 m[/tex]
substituting values
[tex]A = 4 * 3.142 * (6.3781*10^6 \ m)^2[/tex]
[tex]A =5.1128 *10^{14} \ m^2[/tex]
So
[tex]q = -E * A * \epsilon _o[/tex]
Here [tex]\epsilon_o[/tex] s the permitivity of free space with value
[tex]\epsilon_o = 8.85*10^{-12} \ m^{-3} \cdot kg^{-1}\cdot s^4 \cdot A^2[/tex]
substituting values
[tex]q = -102 * 5.1128 *10^{14} * 8.85 *10^{-12}[/tex]
[tex]q = -461532.5 \ C[/tex]
On a separate sheet of paper, tell why scientists in different countries can easily compare the amount of matter in similar objects in their countries
Answer: no u
Explanation: no u
Question 18(Multiple Choice Worth 2 polnis)
When riding your skateboard you crash into a curb, the skateboard stops, and you continue moving forward. Which law of
motion is being described in this scenario?
O Law of Universal Gravitation
o Newton's Second Law of Motion
o Law of Conservation of Energy
o Newton's First Law of Motion
Which statement about friction is true? (1 point)
o
Static friction and kinetic friction in a system always act in opposite directions of each other and in the same direction as the
applied force
Static friction and kinetic friction in a system always act in the same direction as each other and in the opposite direction of the
applied force
Static friction and kinetic friction in a system always act in opposite directions of each other and in the opposite direction of the
applied force
O
Static friction and kinetic friction in a system always act in the same direction as each other and in the same direction as the
applied force.
Answer:static friction and kinetic friction in a system always act in the same direction as each other and n the opposite direction of the applie force . Is the correct answer
Explanation:
Static friction and kinetic friction in a system always act in the same direction as each other and in the opposite direction of the applied force. The correct option is B.
What is friction?Friction is the force that prevents one hard material from scooting or rolling over the other.
Frictional forces, such as the locomotion required to walk without dropping, are advantageous, but they also create a significant amount of resistance to motion.
We can control cars because of friction between the tires and the road: more precisely, because there are three types of friction: rolling friction, starting friction, and sliding friction.
Friction reduces the speed of moving objects and can even stop them from moving. The friction between the objects generates heat. As a result, energy is wasted in the machines. Friction will cause wear and tear on the machine parts.
In a system, static and kinetic friction always act in the same direction and in the opposite direction of the applied force.
Thus, the correct option is B.
For more details regarding friction, visit:
https://brainly.com/question/28356847
#SPJ2
Consider a wire of a circular cross-section with a radius of R = 3.17 mm. The magnitude of the current density is modeled as J = cr2 = 9.00 ✕ 106 A/m4 r2. What is the current (in A) through the inner section of the wire from the center to r = 0.5R?
Answer:
The current is [tex]I = 8.9 *10^{-5} \ A[/tex]
Explanation:
From the question we are told that
The radius is [tex]r = 3.17 \ mm = 3.17 *10^{-3} \ m[/tex]
The current density is [tex]J = c\cdot r^2 = 9.00*10^{6} \ A/m^4 \cdot r^2[/tex]
The distance we are considering is [tex]r = 0.5 R = 0.001585[/tex]
Generally current density is mathematically represented as
[tex]J = \frac{I}{A }[/tex]
Where A is the cross-sectional area represented as
[tex]A = \pi r^2[/tex]
=> [tex]J = \frac{I}{\pi r^2 }[/tex]
=> [tex]I = J * (\pi r^2 )[/tex]
Now the change in current per unit length is mathematically evaluated as
[tex]dI = 2 J * \pi r dr[/tex]
Now to obtain the current (in A) through the inner section of the wire from the center to r = 0.5R we integrate dI from the 0 (center) to point 0.5R as follows
[tex]I = 2\pi \int\limits^{0.5 R}_{0} {( 9.0*10^6A/m^4) * r^2 * r} \, dr[/tex]
[tex]I = 2\pi * 9.0*10^{6} \int\limits^{0.001585}_{0} {r^3} \, dr[/tex]
[tex]I = 2\pi *(9.0*10^{6}) [\frac{r^4}{4} ] | \left 0.001585} \atop 0}} \right.[/tex]
[tex]I = 2\pi *(9.0*10^{6}) [ \frac{0.001585^4}{4} ][/tex]
substituting values
[tex]I = 2 * 3.142 * 9.00 *10^6 * [ \frac{0.001585^4}{4} ][/tex]
[tex]I = 8.9 *10^{-5} \ A[/tex]
You want the current amplitude through a 0.450 mH inductor (part of the circuitry for a radio receiver) to be 1.50 mA when a sinusoidal voltage with an amplitude of 13.0 V is applied across the inductor. What frequency is required?
Answer:
3.067MHzExplanation:
The formula for calculating the voltage across an inductor is expressed as
[tex]V_l = IX_l\\\\Since\ X_l = 2\pi fL\\V_l = I(2\pi fL)[/tex]
Given parameters
current amplitude I = 1.50mA = 1.5*10⁻³A
inductance L = 0.450mH = 0.450*10⁻³H
Voltage across the inductor [tex]V_l[/tex] = 13.0V
Required
frequency f
Substituting the given parametres into the formula, we have;
[tex]V_l = I(2\pi fL)\\\\13 = 1.50*10^{-3}(2*3.14*f*0.450*10^{-3})\\\\13 = 4.239*10^{-6}f\\\\f = \frac{13}{4.239*10^{-6}} \\\\f = 3,066,761 Hertz\\\\f = 3.067MHz[/tex]
Hence, the frequency required is 3.067MHz
