A resistor made of Nichrome wire is used in an application where its resistance cannot change more than 1.35% from its value at 20.0°C. Over what temperature range can it be used (in °C)?

Answers

Answer 1

Answer:

Pls seeattached file

Explanation:

A Resistor Made Of Nichrome Wire Is Used In An Application Where Its Resistance Cannot Change More Than
Answer 2

A resistor made of Ni chrome wire is used in an application where its resistance cannot be more than 1.35 % so its temperature range will be from 33.75 to -33.75 °C.

What is Resistance?

Electrical resistance, or resistance to electricity, is a force that opposes the flow of current. Ohms are used to expressing resistance values.

When there is an electron difference between two terminals, electricity will flow from high to low. In opposition to that flow is resistance. As resistance rises, the current declines. On the other side, when the resistance falls, the current rises.

According to the question,

R = R₀ (1 + α ΔT)

(1 + 0.0135)R₀ = R₀(1 + α ΔT)

ΔT = (1 + 0.0135) / α

= 0.0135 / 0.0004

= 33.75 °C.

ΔT = [(1 - 0.0135) -1]/0.004

= -33.75 °C

To get more information about Resistance :

https://brainly.com/question/11431009

#SPJ5


Related Questions

A skull believed to belong to an ancient human being has a carbon-14 decay rate of 5.4 disintegrations per minute per gram of carbon (5.4 dis/min*gC). If living organisms have a decay rate of 15.3 dis/min*gC, how old is this skull

Answers

Answer:

9.43*10^3 year

Explanation:

For this question, we ought to remember, or know that the half life of carbon 14 is 5730, and that would be vital in completing the calculation

To start with, we use the formula

t(half) = In 2/k,

if we make k the subject of formula, we have

k = in 2/t(half), now we substitute for the values

k = in 2 / 5730

k = 1.21*10^-4 yr^-1

In(A/A•) = -kt, on rearranging, we find out that

t = -1/k * In(A/A•)

The next step is to substitite the values for each into the equation, giving us

t = -1/1.21*10^-4 * In(5.4/15.3)

t = -1/1.21*10^-4 * -1.1041

t = 0.943*10^4 year

Several books are placed on a table. These books have a combined weight of 25 N and cover an area of 0.05 m2. How much pressure do the books exert on the table? The pressure the books apply to the table top is __ Pa.

Answers

Answer:

500 Pascals

Explanation:

[tex]Force = 25N\\Area = 0.05m^2\\\\Pressure = \frac{Force}{Area}\\ \\Pressure = \frac{25}{0.05}\\\\ Pressure = 500 Pascals[/tex]

"If a beam of monochromatic light is passed though a slit of width 15 μm and the second order dark fringe of the diffraction pattern is at an angle of 5.2o from the central axis, what is the wavelength of the light?"

Answers

Answer:

  λ= 5.4379 10⁻⁷ m = 543.79 nm

Explanation:

The phenomenon of diffraction is described by the expression for destructive diffraction is

           a sin θ = (m + 1/2) λ

           λ = a sin θ / (m + 1/2)

let's reduce the magnitudes to the SI system

           a = 15 um = 15 10⁻⁶ m

           m = 2

           θ = 5.2º

Let's calculate

          λ = 15 10⁻⁶ sin 5.2 / (2 +1/2)

         λ = 5.4379 10⁻⁷ m

Let's reduce to nm

          λ= 5.4379 10⁻⁷ m = 543.79 nm

a toy propeller fan with a moment of inertia of .034 kg x m^2 has a net torque of .11Nxm applied to it. what angular acceleration does it experience

Answers

Answer:

The  angular acceleration is  [tex]\alpha = 3.235 \ rad/s ^2[/tex]

Explanation:

From the question we are told that

    The moment of inertia is  [tex]I = 0.034\ kg \cdot m^2[/tex]

     The  net torque is  [tex]\tau = 0.11\ N \cdot m[/tex]

Generally the net torque is mathematically represented as

           [tex]\tau = I * \alpha[/tex]

Where [tex]\alpha[/tex] is the angular acceleration so  

        [tex]\alpha = \frac{\tau }{I}[/tex]

substituting values

         [tex]\alpha = \frac{0.1 1}{ 0.034}[/tex]

        [tex]\alpha = 3.235 \ rad/s ^2[/tex]

A single slit 1.5 mm wide is illuminated by 420- nm light. Part A What is the width of the central maximum (in cm ) in the diffraction pattern on a screen 4.5 m away

Answers

Answer:

The width is [tex]w_c = 0.00252 \ m[/tex]

Explanation:

From the question we are told that

  The  width of the single slit is  [tex]a = 1.5 \ mm = 1.5 *10^{-3} \ m[/tex]

   The  wavelength is  [tex]\lambda = 420 *10^{-9} \ m[/tex]

   The distance of the screen is  [tex]D = 4.5 \ m[/tex]

Generally the width of the central maximum is  

        [tex]w_c = 2 * y[/tex]

where y is the width of the first maxima which is mathematically represented as

       [tex]y = \frac{\lambda * D}{a}[/tex]

=>   [tex]y = \frac{ 420 *10^{-9} * 4.5}{ 1.5*10^{-3}}[/tex]

=>  [tex]y = 0.00126 \ m[/tex]

So

    [tex]w_c = 2 *0.00126[/tex]

    [tex]w_c = 0.00252 \ m[/tex]

Lamar has been running sprints to prepare for his next football game.He has found that he can maintain his maximum speed for 45 yards.He’s thinking of running in a 5km race in a few months,but doesn’t know if he can maintain his maximum speed for the entire 5 km.Can you help him determine how far he can?

Answers

Answer:

Kindly check explanation

Explanation:

Length of race = 5km

Maximum speed = 45 yards

Converting from yards to kilometer :

1km = 1093.613 yards

x = 45 yards

(1093.613 * x) = 45

x = 45 / 1093.613

x = 0.0411480 km

Where x = maximum length for which he can maintain his maximum speed expressed in kilometers.

Therefore, with the available information, it can be concluded that Lamar cannot maintain his maximum speed for the entire 5km race and will only be able maintain his maximum speed for 0.0411 kilometers.

Lamar cannot maintain his maximum speed for the entire 5km race and will only be able maintain his maximum speed for 0.0411 kilometers.

The calculation is as follows;

Length of race = 5km

Maximum speed = 45 yards

Converting from yards to kilometer :

1km = 1093.613 yards

x = 45 yards

[tex](1093.613 \times x) = 45[/tex]

[tex]x = 45 \div 1093.613[/tex]

x = 0.0411480 km

here x represent maximum length for which he can maintain his maximum speed expressed in kilometers.

Learn more: https://brainly.com/question/3617478?referrer=searchResults

It's nighttime, and you've dropped your goggles into a 3.2-m-deep swimming pool. If you hold a laser pointer 1.2 m above the edge of the pool, you can illuminate the goggles if the laser beam enters the water 2.0 m from the edge.
How far are the goggles from the edge of the pool?

Answers

Answer:

Explanation:

Laser angle with water surface is given by: Tan α = 1/2.0= 0.5/

α = 26.56°

Laser angle with Normal = 90 - 26.56 = 63.44 °

Assuming a red laser, refractive index in water is 1.331.

Angle of refraction in water is given by:

Ref Ind = Sin i / Sin r

1.331 = Sin 63.44 / Sin r

Sin r = 0.8945 / 1.331 = 0.6721

Angle r = 42.22°

For the path in water:

Tan 42.22 = x / 3.2

x = 2.9m where x is the lateral displacement of the laser ince it hits the water

So the goggles are 2.0 + 2.9 = 4.9 m from edge of pool

(4) Use the preliminary observations to answer these questions; Compared to no polarizer or analyzer in the optical path, by what percent does the light intensity decrease when (a) The polarizer is introduced into the optical path? (b) The both polarizer and analyzer are introduced into the optical path?

Answers

Answer:

a)   I = I₀/2, b)  I = I₀/2 cos² θ

Explanation:

To answer these questions, let's analyze a little the way of working of a polarized

* When a non-polarized light hits a polarizer, the electric field that is not in the direction of the polarizer is absorbed, so the transmitted light is

          i = I₀ / 2

and is polarized in the direction of the polarizer

* when a polarized light reaches the analyzer it must comply with Malus's law

          I = I₁ cos² θ

where the angle is between the polarized light and the analyzer.

With this, let's answer the questions

a) When a polarizer is placed in the non-polarized light path, half of it is absorbed and only the light that has polarization in the direction of the polarizer is transmitted with an intensity of

                  I = I₀/2

b) when a polarizer and an analyzer are fitted, the intensity of the light transmitted by the analyzer is

                I = I₀/2 cos² θ

where the final value depends on the angle between the polarizer and the analyzer.

Let's look at two extreme cases

θ = 0          I = Io / 2

θ = 90º      I = 0

The Curiosity rover now on Mars analyzed rocks and found magnesium to have the following isotopic composition.
79.70% Mg-24 (23.9872 amu), 10.13% Mg-25 (24.9886 amu), and 10.17% Mg-26 (25.9846 amu).
A. How many neutrons are in Mg-25?
B. What is the average atomic mass of magnesium in these rocks?
C. Is the magnesium composition on Mars the same as that on Earth? Explain.

Answers

Answer:

A.   number of neutrons of Magnesium Mg = 13

B.   The average mass of Mg = 22.29 amu

C.   the magnesium composition on Mars is not the same as that on Earth.

Explanation:

Isotopes are atoms with the same atomic number but different mass number. This is due to the difference in mass of the neutrons.

The atomic number of Magnesium Mg = 12

The atomic number of an element is the number of protons present in the atomic nucleus of the element

i.e Atomic number = number of protons = 12

The mass number of an element is the sum of the protons and neutrons in the atomic nucleus of the element.

Mass number = number of protons + number of neutrons

Given that the mass number of Mg = 25

Then;

25 = 12 + number of neutrons

25 - 12 = number of neutrons

13 = number of neutrons

number of neutrons of Magnesium Mg = 13

B. What is the average atomic mass of magnesium in these rocks?

The average atomic mass of an element which exhibit isotopy is the average mass of its various isotopes as they occur naturally in any quantity of the element.

Therefore the average atomic mass of magnesium can be calculated as:

= [tex]\mathtt{\dfrac{(23.9872 \times 79.70) + ( 24.9886 \times 10.13) + (25.9846 \times 10.17) }{79.7 + 10.13 +10.17}}[/tex]

= [tex]\mathtt{\dfrac{(1911.77984) + ( 53.134518) + (264.263382) }{100}}[/tex]

= [tex]\mathtt{\dfrac{2229.17774 }{100}}[/tex]

The average mass of Mg = 22.29 amu

C. Is the magnesium composition on Mars the same as that on Earth? Explain.

The average atomic weight of magnesium on Earth is said to be 24.305 amu while that of Mars is 22.29 amu.

There difference in the average atomic weight result into difference in their composition. Therefore,the magnesium composition on Mars is not the same as that on Earth.

how many stars are in our solar system?

Answers

Answer:

there are over 100 billion stars in our galaxy.

The generator in a purely inductive AC circuit has an angular frequency of 363 rad/s. If the maximum voltage is 169 V and the inductance is 0.0937 H, what is the rms current in the circuit

Answers

Answer:

The rms current in the circuit is 3.513 A

Explanation:

Given;

angular frequency of the inductor, ω = 363 rad/s

maximum voltage of the inductive AC, V₀ = 169 V

Inductance of the inductor, L = 0.0937 H

Inductive reactance is given by;

[tex]X_L = 2\pi f L= \omega L[/tex]

[tex]X_L = 363 *0.0937\\\\X_L = 34.0131 \ ohms[/tex]

The rms voltage is given by;

[tex]V_{rms} = \frac{V_o}{\sqrt{2} } \\\\V_{rms} =\frac{169}{\sqrt{2} } \\\\V_{rms} = 119.5 \ V[/tex]

The rms current in the circuit is given by;

[tex]I_{rms} = \frac{V_{rms}}{X_L} \\\\I_{rms} = \frac{119.5}{34.0131} \\\\I_{rms} = 3.513 \ A[/tex]

Therefore, the rms current in the circuit is 3.513 A

Three capacitors C1 = 10.7 µF, C2 = 23.0 µF, and C3 = 29.3 µF are connected in series. To avoid breakdown of the capacitors, the maximum potential difference to which any of them can be individually charged is 125 V. Determine the maximum energy stored in the series combination.

Answers

Answer:

E = 1336.71875 J

Explanation:

We are given;. Capacitance of Capacitor 1; C1 = 10.7 µF

Capacitor 2; C2 = 23.0 µF

Capacitor 3; C3 = 29.3 µF

Supply voltage;V = 125 V

Formula for capacitance in series is;

Capacitors in series circuit: C(eq) = 1/C(1) +1/C(2) +1/C(3) .......

Thus, equivalent capacitance is;

C(eq) = (1/10.7) + (1/23) + (1/29.3) = 0.1711 µF = 0.1711 × 10^(6) F

Now, the formula for maximum energy stored is;

E = ½ × C(eq) × V²

E = ½ × 0.1711 × 10^(-6) × 125²

E = 1336.71875 J

A fan rotating with an initial angular velocity of 1500 rev/min is switched off. In 2.5 seconds, the angular velocity decreases to 400 rev/min. Assuming the angular acceleration is constant, answer the following questions.
How many revolutions does the blade undergo during this time?
A) 10
B) 20
C) 100
D) 125
E) 1200

Answers

Answer:

The blade undergoes 40 revolutions, so neither of the given options is correct!

Explanation:

The revolutions can be found using the following equation:

[tex]\theta_{f} = \theta_{i} + \omega_{i}*t + \frac{1}{2}\alpha*t^{2}[/tex]

Where:

α is the angular acceleration

t is the time = 2.5 s

[tex]\omega_{i}[/tex] is the initial angular velocity = 1500 rev/min                

First, we need to find the angular acceleration:

[tex] \alpha = \frac{\omega_{f} - \omega_{i}}{t} = \frac{400 rev/min*2\pi rad*1 min/60 s - 1500 rev/min *2\pi rad*1 min/60 s}{2.5 s} = -46.08 rad/s^{2} [/tex]

Now, the revolutions that the blade undergo are:

[tex]\theta_{f} - \theta_{i} = \omega_{i}*t + \frac{1}{2}\alpha*t^{2}[/tex]

[tex]\Delta \theta = 1500 rev/min *2\pi rad*1 min/60 s*2.5 s - \frac{1}{2}*(46.08 rad/s^{2})*(2.5)^{2} = 248.7 rad = 39.9 rev[/tex]        

Therefore, the blade undergoes 40 revolutions, so neither of the given options is correct!

I hope it helps you!                              

A large reflecting telescope has an objective mirror with a 14.0 m radius of curvature. What angular magnification in multiples does it produce when a 3.25 m focal length eyepiece is used? ✕

Answers

Answer:

The magnification is  [tex]m = -2.15[/tex]

Explanation:

From the question we are told that

   The  radius is  [tex]r = 14.0 \ m[/tex]

    The  focal length eyepiece is  [tex]f_e = 3.25 \ m[/tex]

Generally the objective focal length is mathematically represented as

        [tex]f_o = \frac{r}{2}[/tex]

=>     [tex]f_o = \frac{14}{2}[/tex]

=>     [tex]f_o = 7 \ m[/tex]

The  magnification is mathematically represented as

      [tex]m = - \frac{f_o }{f_e }[/tex]

=>    [tex]m = - \frac{7 }{ 3.25 }[/tex]

=>   [tex]m = -2.15[/tex]

what happened when aniline is treated with benzene diazonium chloride​

Answers

Answer:

p-aminoazobenzene is formed

Explanation:

The reaction of benzene diazonium chloride and aniline takes place in a basic medium and leads to the formation of an azo compound which is also a dye. The terminal diazonium nitrogen of the benzene diazonium ion is coupled to the aniline at the para-position. The product of the reaction, p-aminoazobenzene is a yellow dye.

Benzene diazonium chloride is prepared by diazotization of aniline in the presence of hydrochloric acid. The full reaction of aniline and benzene diazonium chloride​ is shown in the image attached to this answer.

A particle moves along line segments from the origin to the points (1, 0, 0), (1, 5, 1), (0, 5, 1), and back to the origin under the influence of the force field. F(x, y, z)= z^2i + 4xyj + 5y^2kFind the work done.

Answers

Answer:

0 J

Explanation:

Since work done W = ∫F.dr and F(x, y, z)= z²i + 4xyj + 5y²k and dr = dxi + dyj + dzk

F.dr = (z²i + 4xyj + 5y²k).(dxi + dyj + dzk) = z²dx + 4xydy + 5y²dz

W = ∫F.dr = ∫z²dx + 4xydy + 5y²dz = z²x + 2xy² + 5y²z

We now evaluate the work done for the different regions

W₁ = work done from (0,0,0) to (1,0,0)

W₁ = {z²x + 2xy² + 5y²z}₀₀₀¹⁰⁰ = 0²(1) + 2(1)(0)² + 5(0)²(0) - [(0)²(0) + 2(0)(0)² + 5(0)²(0)] = 0 - 0 = 0 J

W₂ = work done from (1,0,0) to (1,5,1)

W₂ = {z²x + 2xy² + 5y²z}₁₀₀¹⁵¹ =   (1)²(1) + 2(1)(5)² + 5(5)²(1) - [0²(1) + 2(1)(0)² + 5(0)²(0)] =  1 + 50 + 125 - 0 = 176 J

W₃ = work done from (1,5,1) to (0,5,1)

W₃ = {z²x + 2xy² + 5y²z}₁₅₁⁰⁵¹ =   1²(0) + 2(0)(5)² + 5(5)²(1) - [(1)²(1) + 2(1)(5)² + 5(5)²(1)]  = 125 - (1 + 50 + 125) = 125 - 176 = -51 J

W₄ = work done from (0,5,1) to (0,0,0)

W₄ = {z²x + 2xy² + 5y²z}₁₅₁⁰⁰⁰ =   (0)²(0) + 2(0)(0)² + 5(0)²(0) - [1²(0) + 2(0)(5)² + 5(5)²(1)] = 0 - 125 = -125 J

The total work done W is thus

W = W₁ + W₂ + W₃ + W₄

W = 0 J + 176 J - 51 J - 125 J

W = 176 J - 176 J

W = 0 J

The total work done equals 0 J

A doctor counts 68 heartbeats in 1.0 minute. What are the corresponding period and frequency of the heart rhythm

Answers

Answer:

[tex]f=1.13s^{-1}=1.13Hz[/tex]

Explanation:

Hello,

In this case, a frequency stands for a rate in which some action is done per unit of time. In this case, for the heartbeat, since 68 actions (heartbeats) occur in 1.0, the frequency turns out:

[tex]f=\frac{68}{1.0min}=68min^{-1}[/tex]

Or as most commonly used in Hz ([tex]s^{-1}[/tex]):

[tex]f=68\frac{1}{min} *\frac{1min}{60s}=1.13s^{-1}=1.13Hz[/tex]

Best regards.

What happens when two polarizers are placed in a straight line, one behind the other? A. They allow light to pass only if they are polarized in exactly the same direction. B. They block all light if they are polarized in exactly the same direction. C. They allow light to pass only if their directions of polarizations are exactly 90° apart. D. They block all light if their directions of polarizations are exactly 90° apart. E. They block all light if their directions of polarizations are either exactly the same or exactly 90° apart.

Answers

Answer:

C

They allow light to pass only if their directions of polarizations are exactly 90° apart.

A fisherman in a stream 39 cm deep looks downward into the water and sees a rock on the stream bed. How deep does the stream appear to the fisherman

Answers

Answer:

30cm

Explanation:

assume that the eyes are substantially above the water so that sin(theta) is approximately theta.

( small angle approximation).

The point at which a ray leaving the fish hits the surface of the water is x to the side of the centreline and the depth of the water is d

x/d = sin( angle of incidence)

if the apparent depth of the water is h then

x/h = sin( angle of refraction)

and applying snells law

1 sin ( theta air) = 1.33 sin( theta water)

1 * x/h = 1.33 * x/d

d/h = 1.33

or h/d = 1/1.33

h/39 = 1.33

h = 39 /1.33 so that is the apparent depth of the stream assuming:-

1. Your eyes are almost directly overhead

and

2. your eyes are a significant distance above the surface of the water.

x/d = 1.33 x/h

h/d =39/1.3

= 30cm

A laser used for many applications of hard surface dental work emits 2780-nm wavelength pulses of variable energy (0-300 mJ) about 20 times per second.part a. Determine the number of photons in one 80-mJ pulse.part b. Determine the average power of photons in one 80-mJ pulse during 1 s.

Answers

Answer:

a

    [tex]n = 1.119 *10^{18} \ photons[/tex]

b

  [tex]P = 1.6 \ W[/tex]

Explanation:

From the question we are told that

    The wavelength is  [tex]\lambda = 2780 nm = 2780 *10^{-9} \ m[/tex]

     The  energy  is  [tex]E = 80 mJ = 80 *10^{-3} \ J[/tex]

This energy is mathematically represented as

     [tex]E = \frac{n * h * c }{\lambda }[/tex]

Where  c is the speed of light with a value  [tex]c = 3.0 *10^{8} \ m/s[/tex]

             h is the Planck's  constant with the value  [tex]h = 6.626 *10^{-34} \ J \cdot s[/tex]

             n is the number of pulses

So

      [tex]n = \frac{E * \lambda }{h * c }[/tex]

substituting values

       [tex]n = \frac{80 *10^{-3} * 2780 *10^{-9}}{6.626 *10^{-34} * 3.0 *10^{8} }[/tex]

       [tex]n = 1.119 *10^{18} \ photons[/tex]

Given that the pulses where emitted 20 times in one second then the period of the pulse is

       [tex]T = \frac{1}{20}[/tex]

      [tex]T = 0.05 \ s[/tex]

Hence the average power of photons in one 80-mJ pulse during 1 s is mathematically represented as

       [tex]P = \frac{E}{T}[/tex]

substituting values

       [tex]P = \frac{ 80 *10^{-3}}{0.05}[/tex]

        [tex]P = 1.6 \ W[/tex]

A bullet is fired from a rifle pointed 45 degrees above horizontal. The bullet leaves the muzzle traveling 1400 m/s. How many seconds does it take the bullet to reach the high point of its trajectory?

Answers

The bullet's vertical velocity at time [tex]t[/tex] is

[tex]v=1400\dfrac{\rm m}{\rm s}-gt[/tex]

where [tex]g=9.80\frac{\rm m}{\mathrm s^2}[/tex] is the acceleration due to gravity.

At its highest point, the bullet's vertical velocity is 0, which happens

[tex]0=1400\dfrac{\rm m}{\rm s}-gt\implies t=\dfrac{1400\frac{\rm m}{\rm s}}g\approx\boxed{142.857\,\mathrm s}[/tex]

(or about 140 s, if you're keeping track of significant figures) after being fired.

a radio antenna emits electromagnetic waves at a frequency of 100 mhz and intensity of what is the photon density

Answers

Answer:

photon density = 1.0 × [tex]10^{16}[/tex] photon/m³

Explanation:

given data

frequency f = 100 mhz = 100 × [tex]10^{6}[/tex] Hz

we consider here intensity I = 0.2 W/m²

solution

we take here plank constant is h i.e = 6.626 × [tex]10^{-34}[/tex] s

and take energy density is E

so here

E × C = I  

E = [tex]\frac{I}{C}[/tex]   ................1

here C = 3 × [tex]10^{8}[/tex] m/s

so photon density is

photon density = [tex]\frac{I}{C} \times \frac{1}{f \times h}[/tex]     ...............2

photon density = [tex]\frac{0.2}{3 \times 10^8} \times \frac{1}{100 \times 10^6 \times 6.626 \times 10^{-34} }[/tex]

photon density = 1.0 × [tex]10^{16}[/tex] photon/m³


A non-ideal battery has a 6.0-V emf and an internal resistance of 0.6 l. Determine the terminal voltage (in volts) when the current drawn from the battery is 1.0 A

Answers

V=I x R = i.0 A x 0.6 ohms = 0.6 volts term = battery V -- int V
=6,0 --0.6 =5.4 volts terminal volts 5.4 volts

what are the applications of pascal's principle​

Answers

Explanation:

The applications are, hydraulic lift- to transmit equal pressure throughout a fluid.Hydraulic jack- used in the braking system of cars.use of a straw- to suck fluids, which goes because of air pressure.The question simply asks, where pressure can be applied. There are many others, such as lift pump.

Warm blooded animals are homeothermic; that is, they maintain an approximately constant body temperature. (Forhumans it's about 37 oC.) When they are in an environment that is below their optimum temperature, they use energy derived from chemical reactions within their bodies to warm them up. One of the ways that animals lose energy to their environment is through radiation. Every object emits electromagnetic radiation that depends on its temperature. For very hot objects like the sun, that radiation is visible light. For cooler objects, like a house or a person, that radiation is in the infrared and is invisible. Nonetheless, it still carries energy. Other ways that energy is lost by a warm animal to a cool environment includes conduction (direct touching of a cooler object) and convection (cooler air moving and carrying thermal energy away). See Heat Transfer for a discussion of all three.

For this problem, we'll just consider how much energy an animal needs to burn (obtain from internal chemical reactions) in order to stay warm just from radiation losses. The rate at which an object loses energy through radiation is given by the Stefan-Boltzmann equation:

Rate of energy loss = AεσT4



where T is the absolute (Kelvin) temperature, A is the area of the object, ε is the emissivity (unitless and =1 for a perfect emitter, less for anything else), and σ is the Stefan-Boltzmann constant:

σ = 5.67 x 10-8 J/(s m2 K4)



Consider a patient trying to sleep naked in a cool room (55 oF = 13 oC). Assume that the person being considered is a perfect emitter and absorber of radiation (ε = 1), has a surface area of about 2.5 m2, and a mass of 80 kg.

a. A person emits thermal radiation at a rate corresponding to a temperature of 37 oC and absorbs radiation at a rate (from the air and walls) corresponding to a temperature of 13 oC. Calculate the individual's net rate of energy loss due to radiation (in Watts = Joules/second).
net rate of energy loss = Watts

b. Assume the patient produces no energy to keep warm. If they have a specific heat about equal to that of water (1 Cal/kg-oC) how much would their temperature fall in one hour? (1 Cal = 1kcal = 103 cal)
ΔT = oC

c. Given that the energy density of fat is about 9 Cal/g, how many grams of fat would the person have to utilize to maintain their body temperature in that environment for one hour?
amount of fat needed = g

Answers

Answer:

a) 360.7 J/s

b) 16.23 °C

c) 34.48 g

Explanation:

The mass of the person = 80 kg

The person is a perfect emitter, ε = 1

surface area of the person = 2.5 m^2

a) If he emits radiation at 37 °C, [tex]T_{out}[/tex] = 37 + 273 = 310 K

and receives radiation at 13 °C, [tex]T_{in}[/tex] = 13 + 273 = 286 K

Rate of energy loss E = Aεσ([tex]T^{4} _{out}[/tex] - [tex]T^{4} _{in}[/tex] )

where σ = 5.67 x 10^-8 J/(s m^2 K^4)

substituting values, we have

E = 2.5 x 1 x 5.67 x 10^-8 x ([tex]310^{4}[/tex] - [tex]286^{4}[/tex]) = 360.7 J/s

b) If they have specific heat about equal to that of water = 1 Cal/kg-°C

but 1 Cal = 1 kcal = 10^3 cal

specific heat of person is therefore = 10^3 cal/kg-°C

heat loss = 360.7 J/s = 360.7 x 3600 = 1298520 J/hr

heat lost in 1 hour = 1 x 1298520 = 1298520 J

This heat lost = mcΔT

where ΔT is the temperature fall

m is the mass

c is the specific heat equivalent to that of water

the specific heat is then = 10^3 cal/kg-°C

equating, we have

1298520 = 80 x 10^3 x ΔT

1298520 = 80000ΔT

ΔT = 1298520/80000 = 16.23 °C

c) 1298520 J = 1298520/4184 = 310.35 Cal

density of fat = 9 Cal/g

gram of fat = 310.35/9 = 34.48 g

A satellite of mass m circles a planet of mass M and radius R in an orbit at a height 2R above the surface of the planet. What minimum energy is required to change the orbit to one for which the height of the satellite is 3R above the surface of the planet

Answers

Answer:

ΔE = GMm/24R

Explanation:

centripetal acceleration a = V^2 / R = 2T/mr

T= kinetic energy

m= mass of satellite, r= radius of earth

= gravitational acceleration = GM / r^2

Now, solving for the kinetic energy:

T = GMm / 2r = -1/2 U,

where U is the potential energy

So the total energy is:

E = T+U = -GMm / 2r

Now we want to find the energy difference as r goes from one orbital radius to another:

ΔE = GMm/2 (1/R_1 - 1/R_2)

So in this case, R_1 is 3R (planet's radius + orbital altitude) and R_2 is 4R

ΔE = GMm/2R (1/3 - 1/4)

ΔE = GMm/24R

A diffraction grating with 161 slits per centimeter is used to measure the wavelengths emitted by hydrogen gas. At what angles in the first-order spectrum would you expect to find the two violet lines of wavelength 434 nm and of wavelength 410 nm

Answers

Answer:

[tex]\theta_1 = 0.400^o[/tex]

[tex]\theta_2 =0.378^o[/tex]

Explanation:

From the question we are told that

    The  number of slits per cm is  k =  [tex]161\ slits\ per\ cm = 161 \ slits\ per\ 0.01 m[/tex]

    The order of the maxima is  n =  1

    The wavelength are  [tex]\lambda_1 = 434 nm = 434 *10^{-9} \ m \ \ \ , \lambda_2 = 410nm = 410 *10^{-9} \ m[/tex]

The  spacing between the slit is mathematically represented as

           [tex]d = \frac{ 0.01}{k}[/tex]

=>       [tex]d = \frac{ 0.01}{161}[/tex]

=>         [tex]d = 6.211 *10^{-5} \ m[/tex]

Generally the condition for constructive interference is  

        [tex]n\lambda = d \ sin \theta[/tex]

At  [tex]\lambda_1[/tex]

      [tex]\theta _1 = sin^{-1} [ \frac{1 * 434 *10^{-9}}{6.211 *10^{-5}} ][/tex]

      [tex]\theta_1 = 0.400^o[/tex]

At  [tex]\lambda_2[/tex]

       [tex]\theta _2 = sin^{-1} [ \frac{1 * 410 *10^{-9}}{6.211 *10^{-5}} ][/tex]

       [tex]\theta_2 =0.378^o[/tex]

The earth has a vertical electric field at the surface,pointing down, that averages 102 N/C. This field is maintained by various atmosphericprocesses, including lightning.
What is the excess charge on the surface of the earth? inC

Answers

Answer:

[tex]q = -461532.5 \ C[/tex]

Explanation:

From the question we are told that

     The  electric filed is  [tex]E = 102 \ N/C[/tex]  

Generally according to Gauss law

=>   [tex]E A = \frac{q}{\epsilon_o }[/tex]

Given that  the electric field is pointing downward  , the equation become

    [tex]- E A = \frac{q}{\epsilon_o }[/tex]

Here   [tex]q[/tex] is the excess charge on the surface of the earth

          [tex]A[/tex] is the surface  area of the of the earth which is mathematically represented as

     [tex]A = 4\pi r^2[/tex]

Where r is the radius of the earth which has a value [tex]r = 6.3781*10^6 m[/tex]

 substituting values

    [tex]A = 4 * 3.142 * (6.3781*10^6 \ m)^2[/tex]

    [tex]A =5.1128 *10^{14} \ m^2[/tex]

So

   [tex]q = -E * A * \epsilon _o[/tex]

Here [tex]\epsilon_o[/tex] s the permitivity of free space with value

          [tex]\epsilon_o = 8.85*10^{-12} \ m^{-3} \cdot kg^{-1}\cdot s^4 \cdot A^2[/tex]

substituting values

     [tex]q = -102 * 5.1128 *10^{14} * 8.85 *10^{-12}[/tex]

     [tex]q = -461532.5 \ C[/tex]

Some radar systems detect the size and shape of objects such as aircraft and geological terrain. Approximately what is the smallest observable detail (in m) utilizing 495 MHz radar?

Answers

Answer:

0.61 m

Explanation:

The smallest observable length by the radar must be at least equal to or greater than the wavelength of the radar.

using the relationship

c = fλ

where

c is the speed of light in vacuum = 3 x 10^8 m/s

f is the frequency of the wave = 495 MHz = 4.95 x 10^8 Hz

λ is the wavelength = ?

λ = c/f = (3 x 10^8)/(4.95 x 10^8) = 0.61 m

answer to your question is 0.6m

A) A 2-N force is applied to a spring, and there is displacement of 0.4 m. How much would the spring be displaced if a 5-N force was applied? (1 point)
1 m
4 m
0.08 m
2 m

Answers

Answer:

Option (A) : 1m

Explanation:

According to Hooke's law:

F (spring elastic force) =

k( spring const.) * x(displacement)

Case-1

2 N = k * 0.4m

k = 5

Case- 2

5 N = 5 * x

x ( displacement) = 1 m

The displacement of the spring if a 5-N force was applied is equal to 1m. Therefore, option (1) is correct.

What is Hooke's law?

The strain and stress are proportional to each other, and this is called Hooke’s Law. Hooke’s law states that the strain is proportional to the stress applied within the elastic limit of the material.

When the materials are stretched, the atoms or molecules deform and when the stress is removed, they will return to their original state.

The mathematical equation for Hooke's law is as follows:

F = –kx

where F is the force, x is displacement, and k is the spring constant in N/m.

Given, F = 2N and x = 0.4m

F = -kx

2 N = - k (0.4m)

k = 5 N/m where the negative sign is omitted.

Now, the spring constant of the spring, k = 5 N/m and F = 5N

F = -kx

5 N = - (5 N/m)(x)

x = - 1m

Therefore, the displacement of the spring is 1 m.

Learn more about Hooke's law, here:

https://brainly.com/question/13348278

#SPJ2

Other Questions
What do you think that David would have predictedbased on his hypothesis? (Set it up as an IFTHEN statement) Using the FOIL method, find the product of x - 2 and x - 3 . Which of the following gulfs are in Southeast Asia? A. the Gulf of Aden and the Gulf of Bahrain B. the Gulf of Mexico and the Gulf of California C. the Gulf of Thailand and the Gulf of Tonkin D. the Gulf of Suez and the Gulf of Oman Explain the accommodation sector of the hospitality industry 1 person = 40 min = 1 bag, 4 person = ? min = 1575 bags In trying to understand the evacuation of the World Trade Center when it was first bombed in 1993, B. E. Aguirre, Dennis Wenger, and Gabriela Vigo argue that the more "the search for meaning in the milling process focuses upon defining the situation as serious, the quicker should be the mobilization of people and the initiation of collective behavior." What type of theory are they using to make this prediction? What does it mean for a government to have a bicameral legislature? if the fed sells $2 million of bonds to the First National bank, what happens to reserves and the monetary base The velocities of light in air and glass are 3.0 x 10^8ms and 2.010^8ms respectively. If the angle of refraction is 30, the sine of the angle of incidence is?Pls help Why princess Margaret couldn't marry Peter Townsend ? Which of these conditions helped establish the foundation for a market revolution in the United States The minimal passing score for a test is 80%. There are 12 exercises on the test. What is the minimum number of correct exercises needed to earn a passing score? Editing work occurs first. Check for wordiness and other sentence mistakes before you worry about content. Select one: True False 1. What does the acronym LASER stand for? What characteristic of a laser makes it suitable for today's experiment? the temperature at which water freezes on the celsius scale is 0 degrees C. It freezes at 32 degrees F on the Fahrenheit scale, write opposites fo these two numbers as integers. Which does not account for the fact that fish can survive the winter in ponds in temperate climate zones? 1. the density of ice versus that of water 2. the unique properties of water 3. the intermolecular bonding of water 4. the tendency for water to freeze from the bottom up In January 2008, the temperature in parts of Minnesota fell from 48 F degrees to -12 F degrees over a 24 hour period. What was the average temperature change per hour? Define enlightenment A. found of Buddhism B. wisdom C. the Buddha's word for release from selfishness and pain D. Nirvana how does the mask help if you well? Aaron wants to mulch his garden. His garden is x^2+18x+81 ft^2 One bag of mulch covers x^2-81 ft^2 . Divide the expressions and simplify to find how many bags of mulch Aaron needs to mulch his garden.