A reversible power cycle R and an irreversible power cycle I operate between the same hot and cold thermal reservoirs. Cycle I has a thermal efficiency equal to one third the thermal efficiency of R.

a. If each cycle receives the same amout of energy by heat transfer from the hot reservor, detrmine which cycle:
1. develops greater net work.
2. discharges greater energy by heat transfer to the cold reservoir

b. If each cycle develops the same net work, determine which cycle:
1. receives greater net energy by heat transfer from the hot reservoir
2. discharges greater energy by heat transfer to the cold reservoir.

Answer:

80⁰C

Explanation:

80°C.

Normal flat plate collectors can deliver heat at temperatures up to 80°C. Deficiency rates for normal flat plate collectors can be classified as visual losses, which produce with cumulative angles of the incident sunshine, and thermal losses, which upsurge fast with the working temperature intensities

Answer: The tracer lathe is a roughing operation for the output shaft on rear wheel drive transmissions.

Explanation:

Answer:

No it is not permitted

Explanation:

It is not permitted  because as per NEC 410.21 policy no other conductor is allowed to be passed through integral junction box luminaries unless such conductor supply recessed luminaries.

The marking will show that the Luminaries is of the right construction or right installation to ensure that the the conductors ( in the outer boxes ) will not be exposed to temperatures greater than the conductor rating, hence the lack of marking makes it not to be permitted.

Answer:

Explanation:

Minerals and rocks are the same. Aggregates of minerals form rocks. Minerals determine the texture of a rock. Most rocks are made of a single mineral type.

Answer:

Answer to the following question is as follows;

Explanation:

It is critical to communicate well during negotiations and conversation in order to attain your objectives. Communication also becomes essential in business and corporation . Effective communication may help you as well as your employees develop a strong professional relationship, which can boost morale and efficiency.

Answer:

Voltage Regulator

Technician A is correct.

Explanation:

Technician B is not correct.  The voltage regulator is not installed between the output terminal of the alternator and the positive terminal of the battery as claimed by Technician B.  Technician A's opinion that the voltage regulator controls the strength of the rotor's magnetic field is correct.  The computer can also be used to control the output of the alternator by controlling the field current.

Answer:

Data Rate Signaling

Answer:

hey. its a big question. solved from *c hegg

Explanation:

Self induction and Mutual induction

If the current through the coil changes, the flux through the coil changes and an emf is induced. Since the emf is induced in the coil due to its own field, it is called self–induced emf and the phenomenon is called self–induction.

Answer:

Self induced EMF is the electro-motive force that is generated due to change in flux in the coil caused by the change in current in the same coil.

Complete Question

Nitrogen (N2) flows through a pipe, entering at at 4 m/sec at 1000 kPa, 2270C. For a pipe inside diameter of 3 cm, find the volumetric flow rate (m3/sec) and the mass flow rate of the gas (kg/sec) assuming you have an ideal gas Then using your ideal gas mass flow rate find the rate at which enthalpy enters the pipe (kJ/sec) NO Cp, Cv, k permitted

Answer:

[tex]H=9.91kJ/sec[/tex]

Explanation:

From the question we are told that:

Velocity [tex]v=4 m/sec[/tex]

Pressure [tex]P=1000kPa[/tex]

Temperature [tex]T=227 \textdegree C[/tex]

Diameter [tex]d=3cm=>0.03m[/tex]

Generally the equation for volumetric Flow Rate is mathematically given by

[tex]V_r=(\frac{\pi*d^2}{4}v)[/tex]

[tex]V_r=(\frac{\pi*(0.03)^2}{4} *4)[/tex]

[tex]V_r=0.002827m^3/s[/tex]

Generally the equation for mass Flow Rate is mathematically given by

[tex]m_r=\frac{PV_r}{RT}[/tex]

[tex]m_r=\frac{1000*0.002827}{0.297*(227+273)}[/tex]

[tex]m_r=0.019kg/sec[/tex]

Generally the equation for mass Flow Rate is mathematically given by

Using gas Table for enthalpy Value

[tex]T=500K=>h=520.75kg[/tex]

Therefore

[tex]H=mh[/tex]

[tex]H=0.019*520.75[/tex]

[tex]H=9.91kJ/sec[/tex]

Complete question:

A steel component with a tensile strength of 800 MPa and fracture toughness Kic=20 MPa Nm is known to contain internal cracks (also called tunnel cracks) with the maximum length of 1.4 mm. This steel is being considered for use in a cyclic loading application for which the designed stresses vary from 0 to 420 MPa. Would you recommend using this steel in this application?

a. Not sure. Because cyclic loading is applied. Fatigue test is needed in order to make the recommendation.

b. Yes, this because the tensile strength of steel is much higher than the applied highest stress of 420 MPa.

c. Yes, this because the calculated critical stress to fracture for the cracks is higher than the highest applied stress of 420 MPa and the steel can withstand the stress of 420 MPa.

d. No. Although the calculated critical stress to fracture for the cracks is slightly higher than the highest applied stress of 420 MPa and the steel may withstand the static stress of 420 MPa, the cyclic loading may cause rapid fatigue fracture.

Answer:

A. Not sure. Because cyclic loading is applied. Fatigue test is needed in order to make the recommendation.

Explanation:

we are not sure if to recommend this alloy for this application given that this material has already been left to experience fatigue degradation. the cyclic load application brings about a growth in the crack. We know that cyclic loading is continuous loading that is useful for the testing of fatigue. Therefore the answer to this question is option a. We cannot make recommendations except fatigue testing has been carried out.

thank you!

Answer:

Explanation:

Increased by the constant. Take a very simple case.

4  +  5 +  6 = 15

The mean is 5  (obtained by dividing the total (15) by the number of terms (3).

Now add a constant say 6

4 + 6 = 10

5 + 6 = 11

6 + 6 = 12

Total = 33/3 = 11

So the mean 5 is increased by the constant 6.

Now do the same thing more symbolically.

4 + c

5 + c

6 + c

Total = 15 + 3c

Divide by 3 you get 5 + c

If you want a more formal proof involving n terms, leave a note.

Answer:

forward voltage triggering

temperature triggering

dv/dt triggering

light triggering

gate triggering

Then turning off;

Turn off is accomplished by a "negative voltage" pulse between the gate and cathode terminals

Explanation:

hope it helps

Answer:

The moment of inertia is basically a physical quantity which describes how easy it is for a body to rotate itself around a given axis.

In easier wording: Moment of Inertia is a body and when it starts rotating or moving, it will keep doing so until we stop it by force.

Explanation:

For example, a car that is moving and active will continue to move even if you were to switch the engine off.

Answer:

I didn't understand your question or is it a fun fact

Answer:

[tex]T_2=315.69k[/tex]

Explanation:

Initial Temperature [tex]T_1=500K[/tex]

Initial Pressure [tex]P_1=1000kPa[/tex]

Final Pressure [tex]P_2=200kPa[/tex]

Generally the gas equation is mathematically given by

[tex]\frac{T_2}{T_1}=\frac{P_2}{P_1}^{\frac{n-1}{n}}[/tex]

Where

n for [tex]CO=1.4[/tex]

Therefore

[tex]\frac{T_2}{500}=\frac{200}{1000}^{\frac{1.4-1}{1.4}}[/tex]

[tex]T_2=315.69k[/tex]

Answer:

c +5

Explanation:

we have difference in energy =

2.18x10⁻¹⁸ x z² / n²

now n = 1

amount of energy absorbed Δdelta = 7.84×10−17 J

7.84×10⁻¹⁷ = 2.18x10⁻¹⁸ x z²

we divide through by 2.18x10⁻¹⁸

z² = 7.84×10⁻¹⁷ / 2.18x10⁻¹⁸

z² = 35.9633

z = √35.9633

z = 5.9969

≈ 6

charge = atomic number 6 - number of electrons available in the element 1

= 6-1 = 5

from the calculations above, the charge of the one electron specie would be c +5

Answer:

It is created on Microsoft Edge

Explanation:

GIS

The full for GIS is : Geographic Information System.

The GIS is a system of mapping that is used to create, analyze, manage and map all the types of data.

It is a method capturing, checking as well as displaying all the data that is related to the position of the surface of earth.

Remote Sensing

Remote sensing is defined as a process where the various physical characteristics of an area are constantly monitored and detected by a process of measuring the reflection of the emitted radiations at ta distance.

The snow covered areas of the Kabul basin can be monitored and analyzed by using the process of GIS and remote sensing.

They provide a continuous source of information and data about snow covered peaks, the amount of snow to the authorities.

Learn More :

https://brainly.in/question/1556256?__cf_chl_captcha_tk__=pmd_2d2d9994422ca43d3cbbcf6322e6c34da175405a-1628654009-0-gqNtZGzNAvijcnBszQ3i

Answer:

you have to report to the federal aviation administration upon request

Explanation:

An unmanned aircraft can also be a drone it is an aircraft that does not have passengers or a human pilot.

Such an aircraft could be fully autonomous but most times they have a human pilot who controls it remotely.

Now you have to report this deviation to the federal aviation administration. This body is responsible for the enforcement of regulations that have to do with the manufacture, operation and maintenance of aircrafts. The body makes sure there is an efficient and safe system for a navigation and they also control air traffic.

Answer:

maybe take a really common toy kids play with or often see, find the average height for the toy and do the math to see how many of those toys stacked ontop of eachother would make up 2000 feet. For example (this isn't accurate btw just an idea of what it would sound like but) "Have you ever seen a barbie doll? well if you stack 400 barbie dolls ontop of their head it would be equal to 2000 feet."

Explanation:

sometimes taking common or beloved objects children have into your examples makes them have a better image of how small or how big something is.

Answer:

Explanation:

% Clears variables and screen

clear; clc

% Asks user for input

n = input('Total number of objects: ');

r = input('Size of subgroup: ');

% Computes and displays permutation according to basic formulas

p = 1;

for i = n - r + 1 : n

   p = p*i;

end

str1 = [num2str(p) ' permutations'];

disp(str1)

% Computes and displays combinations according to basic formulas

str2 = [num2str(p/factorial(r)) ' combinations'];

disp(str2)

=================================================================================

Example: check

How many permutations and combinations can be made of the 15 alphabets, taking four at a time?

The answer is:

32760 permutations

1365 combinations

==================================================================================

Answer:

  5.9 watts

Explanation:

The secondary voltage is the primary voltage multiplied by the turns ratio:

  (120 V)(41) = 4920 V

The power is the product of voltage and current:

  (4920 V)(1.2·10^-3 A) = (4.92)(1.2) W = 5.904 W

The power consumed is about 5.9 watts.

Answer:

hola

Explanation:

Explanation:

so its an question?..........

Answer: all of the above

Explanation:

To drive safely in the station, the correct option is D. All of the above.

It should be noted that when a person is driving, it's essential for the person to drive carefully in a station.

One should not smoke in a station. Also, it's important that the driver should turn on their hazard lights

Furthermore, it's important for one to roll their windows down, turn off the radio and also maintain idle speed.

In conclusion, the correct option is D.

Read related link on:

https://brainly.com/question/18889428