A roller coaster uses 800 000 J of energy to get to the top of the first hill. During this climb, it gains 500 000 J of potential energy and pauses (velocity = 0) for a fraction of a second at the very top before heading down the other side.
a) Draw a sankey diagram for a roller coaster's climb.
Answers
A roller coaster uses 800 000 J of energy to get to the top of the first hill. During this climb, it gains 500 000 J of potential energy and pauses for a fraction of a second at the very top before heading down the other side. At the top of the hill total, the kinetic energy of the roller coaster would be zero as the velocity is zero at the top of the hill, therefore the total mechanical energy is only because of potential energy.
What is mechanical energy?Mechanical energy is the combination of all the energy in motion represented by total kinetic energy and the total stored energy in the system which is represented by total potential energy.
The expression for total mechanical energy is as follows
ME= KE+PE
As total mechanical energy is the sum of all the kinetic as well as potential energy stored in the system.As given in the problem a roller coaster uses 800000 J of energy to get to the top of the first hill. During this climb, it gains 500 000 J of potential energy which means 300000 J of energy is lost in the frictional energy while climbing the hill,
Thus at the top of the hill, the total energy of the roller coasters is only due to the potential energy.
Learn more about mechanical energy from here brainly.com/question/12319302
#SPJ2
Related Questions
Air is compressed polytropically from 150 kPa, 5 meter cube to 800 kPa. The polytropic exponent for the process is 1.28. Determine the work per unit mass of air required for the process in kilojoules
a) 1184
b) -1184
c) 678
d) -678
Answers
Answer:
wegkwe fhkrbhefdb
Explanation:B
How do you know that a liquid exerts pressure?
Answers
Answer:
The pressure of water progressively increases as the depth of the water increases. The pressure increases as the depth of a point in a liquid increases. The walls of the vessel in which liquids are held are likewise subjected to pressure. The sideways pressure exerted by liquids increases as the liquid depth increases.
A painter sets up a uniform plank so that he can paint a high wall. The plank is 2 m long and weighs 400 N. The two supports holding up the plank are placed 0.2 m from either end. Show that the upwards force on each of the planks is 200 N. Draw a sketch.
Answers
The upward force on each supporting plank is 200 N
The given parameters include;
weight of the plank, W₁ = 400 Nlength of the plank, l = 2 mupward force of each supporting plank, = W₂ and W₃To show that the upward force of each supporting plank is 200 N, make the following sketch.
W₂ W₃
↑ ↑
-----------------------------------------------------------------------
0.2m ↓ 0.2m
400 N
The two supporting planks keeps the 2m plank in equilibrium position. If the plank is in equilibrium position the sum of the upward forces equals sum of the downward force.W₂ + W₃ = 400 N
But the distance of each supporting plank from the end is equal, (0.2m).
Then, W₂ = W₃
2W₂ = 400 N
W₂ = 400N/2
W₂ = 200 N
W₃ = 200 N
Therefore, the upward force on each supporting plank that keeps the plank in equilibrium position is 200 N.
To learn more about equilibrium forces visit: https://brainly.com/question/12582625
Cuando el pistón tiene un volumen de 2x10^-4 m^3, el gas en el pistón está a una presión de 150 kPa. El área del pistón es 0.00133 m^2. Calcular la fuerza que el gas ejerce sobre el embolo del pistón.
Answers
Answer:
F = 1.128 10⁸ Pa
Explanation:
Pressure is defined by
P = F / A
If the gas is ideal for equal force eds on all the walls, so on the piston area we have
F = P A
We reduce the pressure to the SI system
P = 150 kpa (1000 Pa / 1kPa = 150 103 Pa
we calculate
F = 150 10³ / 0.00133
F = 1.128 10⁸ Pa
What is the volume of a metal block 3cm long by 2cm wide by 4cm high? What would be the volume of a block twice as long, wide, and high?
Answers
Answer:
Volume of a metal block = 24 cm^3
Volume of a block twice as long, wide and high = 192 cm^3
Explanation:
Volume of a block is measured in l*w*h and in the first block, the sides are 3, 2 and 4 and 3*2*4 = 24
Second block, just double each of the lengths to get 6*4*8 = 192
A man standing in an elevator holds a spring scale with a load of 5 kg suspended from it. What would be the reading of the scale, if the elevator is accelerating downward with an acceleration 3.8 m/s?.
Answers
Answer:
3.1 kg
Explanation:
Applying,
R = m(g-a)..................... Equation 1
Where R = weight of the scale when the elevator is coming down, a = acceleration of the elevator, g = acceleration due to gravith.
From the question,
Given: m = 5 kg, a = 3.8 m/s²
Constant: g = 9.8 m/s²
Substitute these values into equation 1
R = 5(9.8-3.8)
R = 5(6)
R = 30 N
Hence the spring scale is
m' = R/g
m' = 30/9.8
m' = 3.1 kg
A 1.5kg block slides along a frictionless surface at 1.3m/s . A second block, sliding at a faster 4.3m/s , collides with the first from behind and sticks to it. The final velocity of the combined blocks is 2.0m/s . What was the mass of the second block?
Answers
Answer:
The mass of the second block=0.457 kg
Explanation:
We are given that
m1=1.5 kg
v1=1.3m/s
v2=4.3 m/s
V=2.0 m/s
We have to find the mass of the second block.
[tex]m_1v_1+m_2v_2=(m_1+m_2)V[/tex]
Let m2=m
Substitute the values
[tex]1.5(1.3)+m(4.3)=(1.5+m)(2)[/tex]
[tex]1.95+4.3m=3+2m[/tex]
[tex]4.3m-2m=3-1.95[/tex]
[tex]2.3m=1.05[/tex]
[tex]m=\frac{1.05}{2.3}[/tex]
[tex]m=0.457 kg[/tex]
Hence, the mass of the second block=0.457 kg
In the diagram, the crest of the wave is show by:
A
B
C
D
Answers
Answer:
D.
Explanation:
The crest of a wave refers to the highest point of a wave. This is illustrated by D.
I need help with this please!!!!
Answers
Answer:
1.84 hours
I hope it's helps you
which characteristic of nuclear fission makes it hazardous?
Answers
Answer:The radioactive waste
Explanation:Fission is the splitting of a heavy unstable nucleus into two Lighter nuclei
Steel railway tracks are laid at 8oC. What size of expansion gap are needed 10m long rail sections if the ambient temperature varies from -10oC to 50oC? [Linear expansivity of steel = 12 x]
Answers
Answer:
Gap left = Change in length on heating
Gap=Initial length×Coefficient of linear expansion×change in temperature
Gap=10×0.000012×15m
⟹Gap=0.0018 m
this is an example u have to put your equation in it
A cylinder is given a push and then rolls up an inclined plane. If the origin is the starting point, sketch the position, velocity, and acceleration of the cylinder vs. time as it goes up and then down the plane.
Answers
Rays of light coming from the sun (a very distant object) are near and parallel to the principal axis of a concave mirror. After reflecting from the mirror, where will the rays cross each other at a single point?
The rays __________
a. will not cross each other after reflecting from a concave mirror.
b. will cross at the center of curvature.
c. will cross at the point where the principal axis intersects the mirror.
d. will cross at the focal point. will cross at a point beyond the center of curvature.
Answers
A concave mirror is an example of curved mirrors. So that the appropriate answer to the given question is option D. The rays will cross at the focal point.
A concave mirror is a type of mirror in which its inner part is the reflecting surface, while its outer part is the back of the mirror. This mirror reflects all parallel rays close to the principal axis to a point of convergence. It can also be referred to as the converging mirror.
In this type of mirror, all rays of light parallel to the principal axis of the mirror after reflection will cross at the focal point.
Therefore, the required answer to the given question is option D. i.e The rays will cross at the focal point.
For reference: https://brainly.com/question/20380620
A space ship has four thrusters positioned on the top and bottom, and left and right as shown below. The thrusters can be operated independently or together to help the ship navigate in all directions.
Initially, the Space Probe is floating towards the East, as shown below, with a velocity, v. The pilot then turns on thruster #2.
Select one:
a.
Space ship will have a velocity to the West and will be speeding up.
b.
Space ship will have a velocity to the East and will be speeding up.
c.
Space ship will have a velocity to the East and will be slowing down.
d.
Space ship will have a velocity to the West and will be slowing down.
e.
Ship experiences no change in motion.
Answers
Answer:
The correct answer is - c. Spaceship will have a velocity to the East and will be slowing down.
Explanation:
In this case, if turned on thruster #2 then it will exert force on the west side as thruster 2 is on the east side and it can be understood by Newton's third law that says each action has the same but opposite reaction.
As the spaceship engine applies force on the east side then according to the law the exhauster gas applies on towards west direction. It will try to decrease the velocity of the spaceship however, the direction of floating still be east side initally.
. A ball of mass 0.50 kg is rolling across a table top with a speed of 5.0 m/s. When the ball reaches the edge of the table, it rolls down an incline onto the floor 1.0 meter below (without bouncing). What is the speed of the ball when it reaches the floor?
Answers
Answer:
4
Explanation:
5. Steve is driving in his car to take care of some errands. The first errand has him driving to a location 2 km East and 6 km North of his starting location. Once he completes that errand, he drives to the second one which is 4 km East and 2 km South of the first errand. What is the magnitude of the vector that describes how far the car has traveled from its starting point, rounded to the nearest km?
Answers
Answer:
gshshs
Explanation:
hshsksksksbsbbshd
a person lifts 60kg on the surface of the earth, how much mass can he lift on the surface of the moon if he applies same magnitude of force
Answers
Explanation:
Hey there!
According to the question;
A person can lift mass of 60 kg on earth.
mass(m1) = 60kg
acceleration due to gravity on earth (a) = 9.8m/s²
Now;
force (f) = m.a
= 60*9.8
= 588 N
Since, there is application of same magnitude of force on moon,
mass(m) =?
acceleration due to gravity on moon (a) = 1.67m/s²
Now;
force (f) = m.a
588 = m*1.67
m = 352.09 kg
Therefore, the person who can lift the mass of 60 kg on earth can lift mass of 352 kg on moon.
Hope it helps!
A car accelerates from 0 m/s to 25 m/s in 5 seconds. What is the average acceleration of the car.
Answers
Answer:
5 m/s I hope it will help you
Explanation:
mark me as a brainlist answer
The potential difference between the plates of a capacitor is 234 V. Midway between the plates, a proton and an electron are released. The electron is released from rest. The proton is projected perpendicularly toward the negative plate with an initial speed. The proton strikes the negative plate at the same instant the electron strikes the positive plate. Ignore the attraction between the two particles, and find the initial speed of the proton.
I have tried looking at the cramster.com solution manual and do not like the way it is explained. Simply put, I cannot follow what is going on and I am looking for someone who can explain it in plain man's terms and help me understand and get the correct answer. I am willing to give MAX karma points to anyone who can help me through this. Thank you kindly.
Answers
Answer:
The speed of proton is 2.1 x 10^5 m/s .
Explanation:
potential difference, V = 234 V
let the initial speed of the proton is v.
The kinetic energy of proton is
KE = q V
[tex]0.5 mv^2 = e V \\\\0.5\times 1.67\times 10^{-27} v^2 = 1.6\times 10^{-19} \times 234\\\\v=2.1\times 10^5 m/s[/tex]
trong cùng một nhiệt độ, lượng năng lượng trên mỗi mol của chất khí nào lớn nhất
a) Khí đơn nguyên tử
b) Khí có từ ba nguyên tử
c) Khí lưỡng nguyên tử
Answers
One charge is fixed q1 = 5 µC at the origin in a coordinate system, a second charge q2 = -3.2 µC the other is at a distance of x = 90 m from the origin.
What is the potential energy of this pair of charges?
Answers
Answer:
5.4uC
Explanation:
the plane of a 5.0 cm by 8.0 cm rectangular loop wire is parallel to a 0.19 t magnetic field. if the loop carries a current of 6.2 amps, what is the magnitude of the torque on the loop
Answers
Convert 385k to temperature of
Answers
Answer:
233.33°F
Explanation:
(385K - 273.15) * 9/5 + 32 = 233.33°F
Cho dòng điện xoay chiều trong sản xuất và sinh hoạt ở nước ta có tần số f = 50Hz. Tính chu kỳ T và tần số góc ω?
Answers
Answer:
T = 1/f = 1/50(s)
ω = 2πf = 100π (rad/s)
(vote 5 sao nhó :3 )
A circular parallel-plate capacitor whose plates have a radius of 25 cm is being charged with a current of 1.3 A. What is the magnetic field 11 cm from the center of the plates
Answers
The magnetic field at 11 cm from the center of the plates is 2.364 x 10⁻⁷ T.
Given;
radius of the circular plate, d = 25 cm = 0.25 m
current in the plate, I = 1.3 A
distance from the center of the circular plate, r = 11 cm = 0.11 m
To find:
magnetic field (B)The magnetic field from the given distance is calculated as from Biot Savart equation:
[tex]B = \frac{\mu_o I}{2\pi r} \\\\where;\\\\\mu_o \ is \ permeability \ of \ free \ space \ 4\pi \times 10^{-7} \ T.m/A\\\\B = \frac{(4\pi \times 10^{-7} ) \times (1.3)}{2\pi \times 0.11} \\\\B = 2.364 \ \times 10^{-6} \ T[/tex]
Therefore, the magnetic field 11 cm from the center of the plates is 2.364 x 10⁻⁷ T.
Learn more here: https://brainly.com/question/17035710
Choose one. 5 points
Use the equation from week 3:
frequency =
wavespeed
wavelength
and the wavelength you found in #3 to calculate the frequency of this photon (remember the speed of
light is 3E8 m/s);
7.6E14 Hz
6.0E14 Hz
4,6E14 Hz
Answers
Good luck
The frequency is 4,6E14 Hz.
What is the frequency?
Frequency is the fee at which modern changes direction in step with 2nd. it's far measured in hertz (Hz), a worldwide unit of degree wherein 1 hertz is identical to 1 cycle in line with 2d. Hertz (Hz) = One hertz is the same as 1 cycle in step with the second. Cycle = One entire wave of alternating present-day voltage.
Frequency describes the number of waves that pass a hard and fast place in a given quantity of time. So if the time it takes for a wave to skip is half of 2d, the frequency is 2 per 2nd. If it takes 1/one hundred of an hour, the frequency is a hundred in step with hour.
Learn more about frequency here:-https://brainly.com/question/254161
#SPJ2
state the laws of reflection
Answers
Answer:
Explanation:
The law of reflection says that the reflected angle (measured from a vertical line to the surface called the normal) is equal to the reflected angle measured from the same normal line.
All other properties of reflection flow from this one statement.
Vector a has a magnitude of 8 and makes an angle of 45 with positive x axis vector B has also the same magnitude of 8 units and direction along the
Answers
Answer:
prove that Sin^6 ϴ-cos^6ϴ=(2Sin^2ϴ-1)(cos^2ϴ+sin^4ϴ)
please sove step by step with language it is opt maths question
A + B = 6,123 units at angle 112,5 degrees.
A - B = 14,782 units at angle 22,5 degrees.
A car is driving towards an intersection when the light turns red. The brakes apply a constant force of 1,398 newtons to bring the car to a complete stop in 25 meters. If the weight of the car is 4,729 newtons, how fast was the car going initially
Answers
Answer:
the initial velocity of the car is 12.04 m/s
Explanation:
Given;
force applied by the break, f = 1,398 N
distance moved by the car before stopping, d = 25 m
weight of the car, W = 4,729 N
The mass of the car is calculated as;
W = mg
m = W/g
m = (4,729) / (9.81)
m = 482.06 kg
The deceleration of the car when the force was applied;
-F = ma
a = -F/m
a = -1,398 / 482.06
a = -2.9 m/s²
The initial velocity of the car is calculated as;
v² = u² + 2ad
where;
v is the final velocity of the car at the point it stops = 0
u is the initial velocity of the car before the break was applied
0 = u² + 2(-a)d
0 = u² - 2ad
u² = 2ad
u = √2ad
u = √(2 x 2.9 x 25)
u =√(145)
u = 12.04 m/s
Therefore, the initial velocity of the car is 12.04 m/s
Q)what are convex mirrors?
Answers
Answer:
A curved mirror is a mirror with a curved reflecting surface. The surface may be either convex or concave. Most curved mirrors have surfaces that are shaped like part of a sphere, but other shapes are sometimes used in optical devices.
A convex mirror (or lens) is one constructed so that it is thicker in the middle than it is at the edge.
