A single-slit diffraction pattern is formed on a distant screen. Assume the angles involved are small. Part A By what factor will the width of the central bright spot on the screen change if the wavelength is doubled

Answers

Answer 1

Answer:

If the wavelength is doubled, the width of the central bright spot on the screen will increase by a factor of 2 (that is, it will also double).

Explanation:

For a single-slit diffraction, diffraction patterns are found at angles θ for which

w sinθ = mλ

where w is the width

λ is wavelength

m is an integer, m = 1,2,3, ....

From the equation, w sinθ = mλ

For the first case, where nothing was changed

w₁ = mλ₁ / sinθ

Now, If the wavelength is doubled, that is, λ₂ = 2λ₁

The equation becomes

w₂ = mλ₂ / sinθ

Then, w₂ = m(2λ₁) / sinθ

w₂ = 2(mλ₁) / sinθ

Recall that, w₁ = mλ₁ / sinθ

Therefore, w₂ = 2w₁

Hence, If the wavelength is doubled, the width of the central bright spot on the screen will increase by a factor of 2 (that is, it will also double).


Related Questions

You are holding on to one end of a long string that is fastened to a rigid steel light pole. After producing a wave pulse that was 5 mm high and 4 em wide, you want to produce a pulse that is 4 cm wide but 7 mm high. You must move your hand up and down once,
a. a smaller distance up, but take a shorter time.
b. the same distance up as before, but take a shorter time.
c. a greater distance up, but take a longer time.
d. the same distance up as before, but take a longer time.
e. a greater distance up, but take the same time.

Answers

Answer:

It will take. the same distance up as before, but take a longer time

hat a 15 kg body is pulled along a horizontal fictional table by a force of 4N what is the acceleration of the body ​

Answers

Answer:

Acceleration of the body is:

[tex]a=0.27\,\,m/s^2[/tex]

Explanation:

Use Newton's second Law to solve for the acceleration:

[tex]F=m\,\,a\\a=\frac{F}{m} \\a=\frac{4\,N}{15\,\,kg} \\a=0.27\,\,m/s^2[/tex]

A 384 Hz tuning fork produces standing waves with a wavelength of 0.90 m inside a resonance tube. The speed of sound at experimental conditions is

Answers

Answer:

v = 345.6m/s

Explanation:

v = 384 x 0.9 = 345.6

v = 345.6m/s

During the spin cycle of your clothes washer, the tub rotates at a steady angular velocity of 31.7 rad/s. Find the angular displacement Δθ of the tub during a spin of 98.3 s, expressed both in radians and in revolutions.

Answers

Answer:

[tex]\Delta \theta = 3116.11\,rad[/tex] and [tex]\Delta \theta = 495.944\,rev[/tex]

Explanation:

The tub rotates at constant speed and the kinematic formula to describe the change in angular displacement ([tex]\Delta \theta[/tex]), measured in radians, is:

[tex]\Delta \theta = \omega \cdot \Delta t[/tex]

Where:

[tex]\omega[/tex] - Steady angular speed, measured in radians per second.

[tex]\Delta t[/tex] - Time, measured in seconds.

If [tex]\omega = 31.7\,\frac{rad}{s}[/tex] and [tex]\Delta t = 98.3\,s[/tex], then:

[tex]\Delta \theta = \left(31.7\,\frac{rad}{s} \right)\cdot (98.3\,s)[/tex]

[tex]\Delta \theta = 3116.11\,rad[/tex]

The change in angular displacement, measured in revolutions, is given by the following expression:

[tex]\Delta \theta = (3116.11\,rad)\cdot \left(\frac{1}{2\pi} \frac{rev}{rad} \right)[/tex]

[tex]\Delta \theta = 495.944\,rev[/tex]

Two waves are traveling in the same direction along a stretched string. The waves are 45.0° out of phase. Each wave has an amplitude of 7.00 cm. Find the amplitude of the resultant wave.

Answers

Answer:

The amplitude of the resultant wave is 12.93 cm.

Explanation:

The amplitude of resultant of two waves, y₁ and y₂, is given as;

Y = y₁ + y₂

Let y₁ = A sin(kx - ωt)

Since the wave is out phase by φ, y₂ is given as;

y₂ = A sin(kx - ωt + φ)

Y = y₁ + y₂ = 2A Cos (φ / 2)sin(kx - ωt + φ/2 )

Given;

phase difference, φ = 45°

Amplitude, A = 7.00 cm

Y = 2(7) Cos (45 /2) sin(kx - ωt + 22.5° )

Y = 12.93 cm

Therefore, the amplitude of the resultant wave is 12.93 cm.

If two identical wires carrying a certain current in the same direction are placed parallel to each other, they will experience a force of repulsion.
a) true
b) false

Answers

Answer:

The answer is B.  false

Explanation:

Current in the same direction

 When current flow through to parallel conductors of a given length, when the current flows in the same direction

1. A force of attraction between the wires occurs and this tends to draw the wires inward

2. A magnetic field in the same direction is produced.

Current in opposite direction

when the current is in opposite direction

1. Force of repulsion between the two wires occurs, draws the wire outward

2. A magnetic field in opposite direction occurs

What happens to the deflection of the galvanometer needle (due to moving the magnet) when you increase the number of loops

Answers

Answer:

If the magnet is moved, the galvanometer needle will deflect, showing that current is flowing through the coil which will increase total induced electromotive force

Explanation:

galvanometer is an instrument that can detect and measure small current in an electrical circuit.

If the magnet is moved, the galvanometer needle will deflect, showing that current is flowing through the coil. If it is move in a way into the coil,the needle deflect in that way and if it move in another way, it will deflect in the other way.

The total induced emf is equal to the emf induced in each loop by the changing magnetic flux, then multiplied by the number of loops and an increase in the number of loops will cause increase in the total induced emf.

A race-car drives around a circular track of radius RRR. The race-car speeds around its first lap at linear speed v_iv i ​ v, start subscript, i, end subscript. Later, its speed increases to 4v_i4v i ​ 4, v, start subscript, i, end subscript. How does the magnitude of the car's centripetal acceleration change after the linear speed increases

Answers

Answer:

The magnitude of the centripetal acceleration increases by 16 times when the linear speed increases by 4 times.

Explanation:

The initial centripetal acceleration, a of the race-car around the circular track of radius , R with a linear speed v is a = v²/R.

When the linear speed of the race-car increases to v' = 4v, the centripetal acceleration a' becomes a' = v'²/R = (4v)²/R = 16v²/R.

So the centripetal acceleration, a' = 16v²/R.

To know how much the magnitude of the car's centripetal acceleration changes, we take the ratio a'/a = 16v²/R ÷ v²/R = 16

a'/a = 16

a' = 16a.

So the magnitude of the centripetal acceleration increases by 16 times when the linear speed increases by 4 times.


A load of 1 kW takes a current of 5 A from a 230 V supply. Calculate the power factor.

Answers

Answer:

Power factor = 0.87 (Approx)

Explanation:

Given:

Load = 1 Kw = 1000 watt

Current (I) = 5 A

Supply (V) = 230 V

Find:

Power factor.

Computation:

Power factor = watts / (V)(I)

Power factor = 1,000 / (230)(5)

Power factor = 1,000 / (1,150)

Power factor = 0.8695

Power factor = 0.87 (Approx)

Coherent light from a sodium-vapor lamp is passed through a filter that blocks everything except for light of a single wavelength. It then falls on two slits separated by 0.490 mm . In the resulting interference pattern on a screen 2.12 m away, adjacent bright fringes are separated by 2.86 mm . For related problem-solving tips and strategies, you may want to view a Video Tutor Solution of Determining wavelength. Part A What is the wavelength of the light that falls on the slits

Answers

Answer:

λ = 6.61 x 10⁻⁷ m = 661 nm

Explanation:

From the Young's Double Slit experiment, the the spacing between adjacent bright or dark fringes is given by the following formula:

Δx = λL/d

where,

Δx = fringe spacing = 2.86 mm = 2.86 x ⁻³ m

L = Distance between slits and screen = 2.12 m

d = slit separation = 0.49 mm = 0.49 x 10⁻³ m

λ = wavelength of light = ?

Therefore,

2.86 x 10⁻³ m = λ(2.12 m)/(0.49 x 10⁻³ m)

(2.86 x 10⁻³ m)(0.49 x 10⁻³ m)/(2.12 m) = λ

λ = 6.61 x 10⁻⁷ m = 661 nm

If 50 mL of each of the liquids in the answer choices were poured into a 250 mL beaker, which layer would be directly above a small rubber ball with a density of 0.960 g/mL? A. sea water – density of 1.024 g/mL B. mineral oil – density of 0.910 g/mL C. distilled water – density of 1.0 g/mL D. petroleum oil – density of 0.820 g/mL

Answers

Answer:

B. mineral oil – density of 0.910 g/mL.

Explanation:

Hello,

In this case, since the density is known as the degree of compactness a body has (mass in the occupied volume), the higher the density, the higher the weight of the body, therefore, if submerged into a liquid it could float if less dense than the liquid or sink if more dense than the liquid.

In such a way, since the rubber is more dense than mineral (0.960 g/mL > 0.910 g/mL) oil but less dense than distilled water (0.960 g/mL < 1.0 g/mL) we can say that B. mineral oil – density of 0.910 g/mL is directly above it when submerged.

Best regards.

A double-convex thin lens is made of glass with an index of refraction of 1.52. The radii of curvature of the faces of the lens are 60 cm and 72 cm. What is the focal length of the lens

Answers

Answer:

63 cm

Explanation:

Mathematically;

The focal length of a double convex lens is given as;

1/f = (n-1)[1/R1 + 1/R2]

where n is the refractive index of the medium given as 1.52

R1 and R2 represents radius of curvature which are given as 60cm and 72cm respectively.

Plugging these values into the equation, we have:

1/f = (1.52-1)[1/60 + 1/72)

1/f = 0.0158

f = 1/0.0158

f = 63.29cm which is approximately 63cm

What will be the nature of the image formed from both a convex lens and a concave
lens of 20 centimeter focus distance, when the object is placed at a distance of
10 centimeters?​

Answers

Answer:

Explanation:

Using the lens formula

1//f = 1/u+1/v

f is the focal length of the lens

u is the object distance

v is the image distance

For convex lens

The focal length of a convex lens is positive and the image distance can either be negative or positive.

Given f = 20cm and u = 10cm

1/v = 1/f - 1/u

1/v = 1/20-1/10

1/v = (1-2)/20

1/V = -1/20

v = -20/1

v = -20 cm

Since the image distance is negative, this shows that the nature of the image formed by the convex lens is a virtual image

For concave lens

The focal length of a concave lens is negative and the image distance is negative.

Given f = -20cm and u = 10cm

1/v = 1/f - 1/u

1/v = -1/20-1/10

1/v = (-1-2)/20

1/V = -3/20

v = -20/3

v = -6.67 cm

Since the image distance is negative, this shows that the nature of the image formed by the concave lens is a virtual image

Sammy is 5 feet and 5.3 inches tall. What is Sammy's height in inches? ​

Answers

Answer:

[tex]\boxed{\sf 65.3 \ inches}[/tex]

Explanation:

1 foot = 12 inches

Sammy is 5 feet tall.

5 feet = ? inches

Multiply the feet value by 12 to find in inches.

5 × 12

= 60

Add 5.3 inches to 60 inches.

60 + 5.3

= 65.3

65.3 Inches.
12 (1 Foot) X 5= 60 + 5.3 = 65.3

¿Cómo podrías utilizar el sistema de posicionamiento global para proponer recorridos alternativos para llegar a un lugar específico (centro educativo, supermercado, el hogar, el parque, entre otros)?

Answers

Answer:

El sistema de posicionamiento global (conocido mundialmente como GPS) podría utilizarse para proponer recorridos alternativos para llegar a un lugar específico, como un parque, a través de la creación de un recorrido guiado por una aplicación móvil con diferentes rutas de acceso al lugar.

Así, por ejemplo, se crearían diferentes rutas de acceso desde un punto A hasta un punto B, teniendo en cuenta factores como: rapidez, congestión vehicular, pago o no de peajes, posibilidad de acceso a pie y determinados factores extra que influyan en la forma de llegar al lugar. Todo ello plasmado en un mapa interactivo en el cual se señalen las rutas disponibles mediante el marcado del mapa en cuestión.

Find the average magnitude of the induced emf if the change in shape occurs in 0.125 ss and the local 0.504-TT magnetic field is perpendicular to the plane of the loop.

Answers

Complete Question

An emf is induced in a conducting loop of wire 1.12m long as its shape is.

changed from square to circular. Find the average magnitude of the induced emf if the change in shape occurs in 0.125 ss and the local 0.504-TT magnetic field is perpendicular to the plane of the loop.

Answer:

The induced emf is  [tex]\epsilon = 0.0863 \ V[/tex]

Explanation:

From the question we are told that

      The  time taken is  [tex]\Delta t = 0.125 \ s[/tex]

       The magnitude of the magnetic field is  B =  0.504 T

        The length of the loop wire is  [tex]l = 1.12 \ m[/tex]

Generally the circumference of the wire when in circular form is  

          [tex]C = 2 \pi r[/tex]

=>        [tex]l = 2 \pi r[/tex]

=>         [tex]r =[/tex][tex]\frac{l}{2 \pi}[/tex]

=>          [tex]r =[/tex][tex]\frac{1.12}{2 * 3.142}[/tex]

=>        [tex]r =[/tex][tex]0.1782 \ m[/tex]

Now the area of the wire as a circle is

           [tex]A = \pi r^2[/tex]

    =>     [tex]A = 3.142 * (0.1782)^2[/tex]      

     =>    [tex]A = 0.0998 \ m^2[/tex]

The  length of one side of the square is

         [tex]b = \frac{l}{4}[/tex]

         [tex]b = \frac{1.12}{4}[/tex]

         [tex]b = 0.28 \ m[/tex]

Now the area of the wire as a square is

          [tex]A_s = b^2[/tex]

=>          [tex]A_s =(0.28 )^2[/tex]

             [tex]A_s = 0.0784 \ m^2[/tex]

Generally the induced emf is mathematically represented as

        [tex]\epsilon = \frac{B * [A - A_s ]}{\Delta t }[/tex]

=>      [tex]\epsilon = \frac{0.504 * [0.0998 - 0.0784 ]}{0.125 }[/tex]

=>      [tex]\epsilon = 0.0863 \ V[/tex]

   

A vertical spring stretches 3.8 cm when a 13-g object is hung from it. The object is replaced with a block of mass 20 g that oscillates in simple harmonic motion. Calculate the period of motion.

Answers

Answer:

The period of motion is 0.5 second.

Explanation:

Given;

extension of the spring, x = 3.8 cm = 0.038 m

mass of the object, m = 13 g = 0.013 kg

Determine the force constant of the spring, k;

F = kx

k = F / x

k = mg / x

k = (0.013 x 9.8) / 0.038

k = 3.353 N/m

When the object is replaced with a block of mass 20 g, the period of motion is calculated as;

[tex]T = 2\pi\sqrt{\frac{m}{k} } \\\\T = 2\pi\sqrt{\frac{0.02}{3.353} } \\\\T = 0.5 \ second[/tex]

Therefore, the period of motion is 0.5 second.

Warm blooded animals are homeothermic; that is, they maintain an approximately constant body temperature. (Forhumans it's about 37 oC.) When they are in an environment that is below their optimum temperature, they use energy derived from chemical reactions within their bodies to warm them up. One of the ways that animals lose energy to their environment is through radiation. Every object emits electromagnetic radiation that depends on its temperature. For very hot objects like the sun, that radiation is visible light. For cooler objects, like a house or a person, that radiation is in the infrared and is invisible. Nonetheless, it still carries energy. Other ways that energy is lost by a warm animal to a cool environment includes conduction (direct touching of a cooler object) and convection (cooler air moving and carrying thermal energy away). See Heat Transfer for a discussion of all three.

For this problem, we'll just consider how much energy an animal needs to burn (obtain from internal chemical reactions) in order to stay warm just from radiation losses. The rate at which an object loses energy through radiation is given by the Stefan-Boltzmann equation:

Rate of energy loss = AεσT4



where T is the absolute (Kelvin) temperature, A is the area of the object, ε is the emissivity (unitless and =1 for a perfect emitter, less for anything else), and σ is the Stefan-Boltzmann constant:

σ = 5.67 x 10-8 J/(s m2 K4)



Consider a patient trying to sleep naked in a cool room (55 oF = 13 oC). Assume that the person being considered is a perfect emitter and absorber of radiation (ε = 1), has a surface area of about 2.5 m2, and a mass of 80 kg.

a. A person emits thermal radiation at a rate corresponding to a temperature of 37 oC and absorbs radiation at a rate (from the air and walls) corresponding to a temperature of 13 oC. Calculate the individual's net rate of energy loss due to radiation (in Watts = Joules/second).
net rate of energy loss = Watts

b. Assume the patient produces no energy to keep warm. If they have a specific heat about equal to that of water (1 Cal/kg-oC) how much would their temperature fall in one hour? (1 Cal = 1kcal = 103 cal)
ΔT = oC

c. Given that the energy density of fat is about 9 Cal/g, how many grams of fat would the person have to utilize to maintain their body temperature in that environment for one hour?
amount of fat needed = g

Answers

Answer:

a) 360.7 J/s

b) 16.23 °C

c) 34.48 g

Explanation:

The mass of the person = 80 kg

The person is a perfect emitter, ε = 1

surface area of the person = 2.5 m^2

a) If he emits radiation at 37 °C, [tex]T_{out}[/tex] = 37 + 273 = 310 K

and receives radiation at 13 °C, [tex]T_{in}[/tex] = 13 + 273 = 286 K

Rate of energy loss E = Aεσ([tex]T^{4} _{out}[/tex] - [tex]T^{4} _{in}[/tex] )

where σ = 5.67 x 10^-8 J/(s m^2 K^4)

substituting values, we have

E = 2.5 x 1 x 5.67 x 10^-8 x ([tex]310^{4}[/tex] - [tex]286^{4}[/tex]) = 360.7 J/s

b) If they have specific heat about equal to that of water = 1 Cal/kg-°C

but 1 Cal = 1 kcal = 10^3 cal

specific heat of person is therefore = 10^3 cal/kg-°C

heat loss = 360.7 J/s = 360.7 x 3600 = 1298520 J/hr

heat lost in 1 hour = 1 x 1298520 = 1298520 J

This heat lost = mcΔT

where ΔT is the temperature fall

m is the mass

c is the specific heat equivalent to that of water

the specific heat is then = 10^3 cal/kg-°C

equating, we have

1298520 = 80 x 10^3 x ΔT

1298520 = 80000ΔT

ΔT = 1298520/80000 = 16.23 °C

c) 1298520 J = 1298520/4184 = 310.35 Cal

density of fat = 9 Cal/g

gram of fat = 310.35/9 = 34.48 g

In a double‑slit interference experiment, the wavelength is lambda=487 nm , the slit separation is d=0.200 mm , and the screen is D=48.0 cm away from the slits. What is the linear distance Δx between the eighth order maximum and the fourth order maximum on the screen?

Answers

Answer:

Δx = 4.68 x 10⁻³ m = 4.68 mm

Explanation:

The distance between the consecutive maxima, in Young's Double Slit Experiment is given bu the following formula:

Δx = λD/d

So, the distance between the eighth order maximum and the fourth order maximum on the screen will be given as:

Δx = 4λD/d

where,

Δx = distance between eighth order maximum and fourth order maximum=?

λ = wavelength = 487 nm = 4.87 x 10⁻⁷ m

d = slit separation = 0.2 mm = 2 x 10⁻⁴ m

D = Distance between slits and screen = 48 cm = 0.48 m

Therefore,

Δx = (4)(4.87 x 10⁻⁷ m)(0.48 m)/(2 x 10⁻⁴ m)

Δx = 4.68 x 10⁻³ m = 4.68 mm

g One of the harmonics in an open-closed tube has frequency of 500 Hz. The next harmonic has a frequency of 700 Hz. Assume that the speed of sound in this problem is 340 m/s. a. What is the length of the tube

Answers

Answer:

The length of the tube is 85 cm

Explanation:

Given;

speed of sound, v = 340 m/s

first harmonic of open-closed tube is given by;

N----->A , L= λ/₄

λ₁ = 4L

v = Fλ

F = v / λ

F₁ = v/4L

Second harmonic of open-closed tube is given by;

L = N-----N + N-----A, L = (³/₄)λ

[tex]\lambda = \frac{4L}{3}\\\\ F= \frac{v}{\lambda}\\\\F_2 = \frac{3v}{4L}[/tex]

Third harmonic of open-closed tube is given by;

L = N------N + N-----N + N-----A, L = (⁵/₄)λ

[tex]\lambda = \frac{4L}{5}\\\\ F= \frac{v}{\lambda}\\\\F_3 = \frac{5v}{4L}[/tex]

The difference between second harmonic and first harmonic;

[tex]F_2 -F_1 = \frac{3v}{4L} - \frac{v}{4L}\\\\F_2 -F_1 = \frac{2v}{4L} \\\\F_2 -F_1 =\frac{v}{2L}[/tex]

The difference between third harmonic and second harmonic;

[tex]F_3 -F_2 = \frac{5v}{4L} - \frac{3v}{4L}\\\\F_3 -F_2 = \frac{2v}{4L} \\\\F_3 -F_2 =\frac{v}{2L}[/tex]

Thus, the difference between successive harmonic of open-closed tube is

v / 2L.

[tex]700H_z- 500H_z= \frac{v}{2L} \\\\200 = \frac{v}{2L}\\\\L = \frac{v}{2*200} \\\\L = \frac{340}{2*200}\\\\L = 0.85 \ m\\\\L = 85 \ cm[/tex]

Therefore, the length of the tube is 85 cm

A wire of 5.8m long, 2mm diameter carries 750ma current when 22mv potential difference is applied at its ends. if drift speed of electrons is found then:_________.
(a) The resistance R of the wire(b) The resistivity p, and(c) The number n of free electrons per unit volume.​

Answers

Explanation:

According to Ohms Law :

V = I * R

(A) R (Resistance) = 0.022 / 0.75 = 0.03 Ohms

Also,

[tex]r = \alpha \frac{length}{area} = \alpha \frac{5.8}{3.14 \times 0.001 \times 0.001} [/tex]

(B)

[tex] \alpha(resistivity) = 1.62 \times {10}^{ - 8} [/tex]

Drift speed is missing. It is given as;

1.7 × 10^(-5) m/s

A) R = 0.0293 ohms

B) ρ = 1.589 × 10^(-8)

C) n = 8.8 × 10^(28) electrons

This is about finding, resistance and resistivity.

We are given;

Length; L = 5.8 m

Diameter; d = 2mm = 0.002 m

Radius; r = d/2 = 0.001 m

Voltage; V = 22 mv = 0.022 V

Current; I = 750 mA = 0.75 A

Area; A = πr² = 0.001²π

Drift speed; v_d = 1.7 × 10^(-5) m/s

A) Formula for resistance is;

R = V/I

R = 0.022/0.75

R = 0.0293 ohms

B) formula for resistivity is given by;

ρ = RA/L

ρ = (0.0293 × 0.001²π)/5.8

ρ = 1.589 × 10^(-8)

C) Formula for current density is given by;

J = n•e•v_d

Where;

J = I/A = 0.75/0.001²π A/m² = 238732.44 A/m²

e is charge on an electron = 1.6 × 10^(-19) C

v_d = 1.7 × 10^(-5) m/s

n is number of free electrons per unit volume

Thus;

238732.44 = n(1.6 × 10^(-19) × 1.7 × 10^(-5))

238732.44 = (2.72 × 10^(-24))n

n = 238732.44/(2.72 × 10^(-24))

n = 8.8 × 10^(28)

Read more at; brainly.com/question/17005119

A lamp in a child's Halloween costume flashes based on an RC discharge of a capacitor through its resistance. The effective duration of the flash is 0.220 s, during which it produces an average 0.520 W from an average 3.00 V.
A. How much charge moves through the lamp (C)?
B. Find the capacitance (F).
C. What is the resitance of the lamo?

Answers

Answer:

A. 0.0374C

B. 0.012F

C. 18 ohms

Explanation:

See attached file

How much energy is required to accelerate a spaceship with a rest mass of 121 metric tons to a speed of 0.509 c?

Answers

Answer

1.07E22 Joules

Explanation;

We know that mass expands by a factor

=>>1/√[1-(v/c)²]

But v= 0.509c

So

1/√(1 - 0.509²)

=>>> 1/√(1 - 0.2591)

= >> 1/√(0.7409) = 1.16

But given that 121 tons is rest mass so 121- 1.16= 119.84 tons is kinetic energy

And we know that rest mass-energy equivalence is 9 x 10^19 joules per ton.

So Multiplying by 119.84

Kinetic energy will be 1.07x 10^22 joules

An object on a level surface experiences a horizontal force of 12.7 N due to kinetic friction. The coefficient of kinetic friction is 0.42.
What is the mass of the object? (Express your answer to two significant figures)kg

Answers

Answer:

The mass of the object is 3.08 kg.

Explanation:

The horizontal force is12.7 N and the coefficient of the kinetic fraction are 0.42. Now we have to compute the mass of the object. Thus, use the below formula to find the mass of the object.

Let the mass of the object = m.

The coefficient of kinetic friction, n = 0.42

Therefore,  

Force, F = n × mg

12.7 = 0.42 × 9.8 × m

m = 3.08 kg

The mass of the object is 3.08 kg.

All household circuits are wired in parallel. A 1140-W toaster, a 270-W blender, and a 80-W lamp are plugged into the same outlet. (The three devices are in parallel when plugged into the same outlet.) Assume that this is the standard household 120-V circuit with a 15-A fuse.
a. What current is drawn by each device?
b. To see if this combination will blow the 15-A fuse, find the total current used when all three appliances are on.

Answers

Answer:

total current = 12.417 A

so it will not fuse as current is less than 15 A

Explanation:

given data

toaster = 1140-W

blender = 270-W

lamp = 80-W

voltage = 120 V

solution

we know that current is express as

current = power ÷ voltage   ......................1

here voltage is same in all three device

so

current by toaster is

I = [tex]\frac{1140}{120}[/tex]

I = 9.5 A

and

current by blender

I = [tex]\frac{270}{120}[/tex]

I = 2.25 A

and

current by lamp is

I = [tex]\frac{80}{120}[/tex]

I = 0.667 A

so here device in parallel so

total current is = 9.5 A + 2.25 A + 0.667 A

total current = 12.417 A

so it will not fuse as current is less than 15 A

UVC light used in sterilizers, has wavelengths between 100 to 280 nm. If a certain UVC wave has a wavelength of 142.9 nm, what is the energy of one of its photons in J

Answers

Answer:

The energy of one of its photons is 1.391 x 10⁻¹⁸ J

Explanation:

Given;

wavelength of the UVC light, λ = 142.9 nm = 142.9 x 10⁻⁹ m

The energy of one photon of the UVC light is given by;

E = hf

where;

h is Planck's constant = 6.626 x 10⁻³⁴ J/s

f is frequency of the light

f = c / λ

where;

c is speed of light = 3 x 10⁸ m/s

λ  is wavelength

substitute in the value of f into the main equation;

E = hf

[tex]E = \frac{hc}{\lambda} \\\\E = \frac{6.626*10^{-34} *3*10^{8}}{142.9*10^{-9}} \\\\E = 1.391*10^{-18} \ J[/tex]

Therefore, the energy of one of its photons is 1.391 x 10⁻¹⁸ J

A 70 kg man floats in freshwater with 3.2% of his volume above water when his lungs are empty, and 4.85% of his volume above water when his lungs are full.

Required:
a. Calculate the volume of air he inhales - called his lung capacity - in liters.
b. Does this lung volume seem reasonable?

Answers

Answer:

Explanation:

A) Vair = 1.3 L

B) Volume is not reasonable

Explanation:

A)

Assume

m to be total mass of the man

mp be the mass of the man that pulled out of the water

m1 be the mass above the water with the empty lung

m2 be the mass above the water with full lung

wp be the weight that the buoyant force opposes as a result of the air.

Va be the volume of air inside man's lungs

Fb be the buoyant force due to the air in the lung

given;

m = 78.5 kg

m1 = 3.2% × 78.5 = 2.5 kg

m2 = 4.85% × 78.5 = 3.8kg

But, mp = m2- m1

mp = 3.8 - 2.5

mp = 1.3kg

So using

Archimedes principle, the relation for formula for buoyant force as;

Fb = (m_displaced water)g = (ρ_water × V_air × g)

Where ρ_water is density of water = 1000 kg/m³

Thus;

Fb = wp = 1.3× 9.81

Fb = 12.7N

But

Fb = (ρ_water × V_air × g)

So

Vair = Fb/(ρ_water × × g)

Vair = 12.7/(1000 × 9.81)

V_air = 1.3 × 10^(-3) m³

convert to litres

1 m³ = 1000 L

Thus;

V_air = 1.3× 10^(-3) × 1000

V_air = 1.3 L

But since the average lung capacity of an adult human being is about 6-7litres of air.

Thus, the calculated lung volume is not reasonable

Explanation:

Which of
of
these
following material is
used as fuse material?
carbon,
silver
Copper
Aluminium

Answers

The provided question is not correct as, there is more than one options are correct, however the explaining every correct option -

Answer:

The correct answer are - silver, copper and aluminium all three used as fuse material.

Explanation:

A safety device in any electric circuit of that prevents the electric system in case of short circuit by breaking the connection of electric system or circuit termed as the Fuse or fuse element. Normally the fuse are made up of wire or element of material that are low in melting point and high in resistance.

Zinc, lead, tin, silver, copper, aluminium, and alloy of tin and alloy are used as fuse element or material for their low melting point and high resistance these are easily breaks the electric path in case of short circuit.

A toroidal solenoid has 590 turns, cross-sectional area 6.20 cm^2 , and mean radius 5.00 cm .Part A. Calcualte the coil's self-inductance.Part B. If the current decreases uniformly from 5.00 A to 2.00 A in 3.00 ms, calculate the self-induced emf in the coil.Part C. The current is directed from terminal a of the coil to terminal b. Is the direction of the induced emf froma to b or from b to a?

Answers

Complete Question

A toroidal solenoid has 590 turns, cross-sectional area 6.20 cm^2 , and mean radius 5.00 cm .

Part A. Calculate  the coil's self-inductance.

Part B. If the current decreases uniformly from 5.00 A to 2.00 A in 3.00 ms, calculate the self-induced emf in the coil.

Part C. The current is directed from terminal a of the coil to terminal b. Is the direction of the induced emf from a to b or from b to a?

Answer:

Part A  

       [tex]L = 0.000863 \ H[/tex]

Part B  

       [tex]\epsilon = 0.863 \ V[/tex]

Part C

    From terminal a to terminal b

Explanation:

From the question we are told that

      The  number of turns is  [tex]N = 590 \ turns[/tex]

      The cross-sectional area is  [tex]A = 6.20 cm^2 = 6.20 *10^{-4} \ m[/tex]

      The  radius is [tex]r = 5.0 \ cm = 0.05 \ m[/tex]

       

Generally the coils self -inductance is mathematically represented as

              [tex]L = \frac{ \mu_o N^2 A }{2 \pi * r }[/tex]

Where [tex]\mu_o[/tex] is the permeability of  free space with value [tex]\mu_o = 4\pi * 10^{-7} N/A^2[/tex]

substituting values

             [tex]L = \frac{ 4\pi * 10^{-7} * 590^2 6.20 *10^{-4} }{2 \pi * 0.05 }[/tex]

             [tex]L = \frac{ 2 * 10^{-7} * 590^2 6.20 *10^{-4} }{ 0.05 }[/tex]

             [tex]L = 0.000863 \ H[/tex]

Considering the Part B

      Initial current is [tex]I_1 = 5.00 \ A[/tex]

      Current at time t is [tex]I_t = 3.0 \ A[/tex]

       The  time taken is  [tex]\Delta t = 3.00 ms = 0.003 \ s[/tex]

The self-induced emf is mathematically evaluated as

          [tex]\epsilon = L * \frac{\Delta I}{ \Delta t }[/tex]          

=>         [tex]\epsilon = L * \frac{ I_1 - I_t }{ \Delta t }[/tex]

substituting values

             [tex]\epsilon = 0.000863 * \frac{ 5- 2 }{ 0.003 }[/tex]  

             [tex]\epsilon = 0.863 \ V[/tex]

The direction of the induced emf is  from a to b because according to Lenz's law the induced emf moves in the same direction as the current

This question involves the concepts of the self-inductance, induced emf, and Lenz's Law

A. The coil's self-inductance is "0.863 mH".

B. The self-induced emf in the coil is "0.58 volts".

C. The direction of the induced emf is "from b to a".

A.

The self-inductance of the coil is given by the following formula:

[tex]L=\frac{\mu_oN^2A}{2\pi r}[/tex]

where,

L = self-inductance = ?

[tex]\mu_o[/tex] = permeability of free space = 4π x 10⁻⁷ N/A²

N = No. of turns = 590

A = Cross-sectional area = 6.2 cm² = 6.2 x 10⁻⁴ m²

r = radius = 5 cm = 0.05 m

Therefore,

[tex]L=\frac{(4\pi\ x\ 10^{-7}\ N/A^2)(590)^2(6.2\ x\ 10^{-4}\ m^2)}{2\pi(0.05\ m)}[/tex]

L = 0.863 x 10⁻³ H = 0.863 mH

B.

The self-induced emf is given by the following formula:

[tex]E=L\frac{\Delta I}{\Delta t}\\\\[/tex]

where,

E = self-induced emf = ?

ΔI = change in current = 2 A

Δt = change in time = 3 ms = 0.003 s

Therefore,

[tex]E=(0.000863\ H)\frac{2\ A}{0.003\ s}[/tex]

E = 0.58 volts

C.

According to Lenz's Law, the direction of the induced emf always opposes the change in flux that causes it. Hence, the direction of the induced emf will be from b to a.

Learn more about Lenz's Law here:

https://brainly.com/question/12876458?referrer=searchResults

A string of holiday lights has 15 bulbs with equal resistances. If one of the bulbs
is removed, the other bulbs still glow. But when the entire string of bulbs is
connected to a 120-V outlet, the current through the bulbs is 5.0 A. What is the
resistance of each bulb?

Answers

Answer:

Resistance of each bulb = 360 ohms

Explanation:

Let each bulb have a resistance r .

Since, even after removing one of the bulbs, the circuit is closed and the other bulbs glow. Therfore, the bulbs are connected in Parallel connection.

[tex] \frac{1}{r(equivalent)} = \frac{1}{r1} + \frac{1}{r2} + + + + \frac{1}{r15} [/tex]

[tex] \frac{1}{r(equivalent)} = \frac{15}{r} [/tex]

R(equivalent) = r/15

Now, As per Ohms Law :

V = I * R(equivalent)

120 V = 5 A * r/15

r = 360 ohms

Other Questions
What happens to the rate of dissolution as the temperature is increased in a gas solution?A. The rate stays the same.B. The rate decreases.C. The rate increases.D. There is no way to tell. is the sentence, " around the corner" a clause or is it a phrase? The block moves up an incline with constant speed. What is the total work WtotalWtotalW_total done on the block by all forces as the block moves a distance LLL the standard form: four and sixty-eight hundredths Each year, public schools are rewarded with bigger budgets for achieving a rating of "excellent" or "recommended" and are punished for rating "needs improvement." These ratings are based on meeting thresholds on a broad set of measures such as attendance rates, graduation rates, standardized test scores, SAT scores, and so on. True or False: This funding structure incentivizes schools to seek out and serve lower-performing students. True False Shortly after receiving a traffic ticket for speeding, Fred made numerous comments about the road signs being inadequate and is GPS telling him a different speed limit. This would be an example of: Loreto quera decorar un viejo tambor metlico para usarlo de paragero. Para ello, contaba con un grueso cordn que pretenda pegar en el contorno del borde superior del tambor. Sabiendo que el dimetro de este era 58,5 cm, cort el cordn, dejando el trozo ms largo de 175,5 cm de longitud de modo que le alcanzara justo, pero le faltaron 7 cm. Cul fue el error de Loreto? Your friend Stacy has given you the following algebraic expression: "Subtract 20times a number n from twice the cube of the number. What is the expression that yourfriend is saying? 60 POINTS!! I NEED HELP ASAP PLEASE!!!! ILL GIVE 5 STAR+BRAINLIEST!! SOMEBODY HAVE THE ANSWERS TO THIS ENTIRE CHART??(it is edmentum) In this task, you will further explore some of the issues you learned about in the unit. You will also research the UN agencies that work on resolving these issues. Complete the table with the following information for each global issue: Write a description of the issue in your own words. These issues were covered in the unit, but you may need to research them for further clarity. Identify the UN agencies that are involved in resolving each issue. To research the agencies, consult this list of UN agencies. Keep in mind that more than one UN agency may be assigned to deal with some problems. The issue of population is addressed in the first row of the table as an example. Ou Esaplain different form of oxygen? brain is considered as the centre of all senses, why ? Manuel made at least one error as he found the value of this expression. Identify the step in which Manuel made his first error. After identifying the step with the first error, explain the corrected steps and find the final answer. PLEASE HELPRead this passage from Giovanna's evaluation of an argument claiming that climate change is not affected by human activity. Niemand's article on climate change in the editorial section of today's newspaper offers a weak argument. His reasoning consists of little more than unsubstantiated assertions that climate change is not affected by human activity. In an effective evaluation, which element would follow this statement? a summary of Niemand's claim text evidence from Niemand's argument a restatement of Giovanna's evaluation the name and source of Niemand's article Dave loves a bargain and buys a feather boa whichhas been reduced in price by 70%. If the sale priceis 2.85, what was the original price of the boa? Choose one jazz musician and discuss his/her contributions to jazz. What influence did this person have on the development and evolution of jazz music? Why did tensions develop between Great Britain and China in the mid-19th century Pauley Company needs to determine a markup for a new product. Pauley expects to sell 15,000 units and wants a target profit of $22 per unit. Additional information is as follows:Variable product cost per unit $19Variable administrative cost per unit 11Total fixed overhead 13,500Total fixed administrative 21,000Using the variable cost method, what markup percentage to variable cost should be used? If a diode at 300K with a constant bias current of 100A has a forward voltage of 700mV across it, what will the voltage drop across this same diode be if the bias current is increased to 1mA? g Mayte, qu gorras te gustan, las rojas o las anaranjadas? Mayte, qu gorras le gustan, las rojas o las anaranjadas? Mayte, qu gorras te gusta, las rojas o las anaranjadas? Mayte, qu gorras le gusta, las rojas o las anaranjadas? What is hand sanitizer