A wave interaction that occurs when two waves are in the same place at the same time

Answer:

Yo dude, if you had a beaker of liquid in outer space, it wouldn't push down on the bottom or the sides of the beaker like it would on Earth. In space, there's no gravity to make the liquid settle down, so it forms a round shape because of surface tension. So basically, the liquid would just float around in a ball inside the beaker. If you moved the beaker around, the liquid would just roll around with it like a bouncy ball.

Answer:B

Explanation:The ray above makes a 90 degree angle. The ray below makes a 60 degree angle.

a.  the depth of cut  is 0.625 inches.

b. the material removal rate is 0.003125 cubic inches per minute.

c. the time required to complete the cutting pass is 20 minutes.

a) The required depth of cut can be determined by :

DOC = (4 in - 2.75 in)/2 = 0.625 in

Therefore, the depth of cut is  0.625 inches.

b) The material removal rate can be found by applying:

MRR = DOC x Width of cut x Feed rate

assuming we are using a standard carbide insert tool with a width of cut of 0.5 inches.

MRR = 0.625 in x 0.5 in x 0.010 in/rev = 0.003125 cubic inches per minute

c) The time required to complete the cutting pass is determined by:

Time = Length of cut / (Cutting speed x Width of cut x Feed rate)

Time = 48 in / (400 ft/min x (0.5 in) x (0.010 in/rev) x (1/12 ft/in)) = 20 minutes

Learn more about material removal rate  at: https://brainly.com/question/13106351

#SPJ1

A) The capacitance of the spherical capacitor is 1.45 pF (picofarads), B) The radius of the inner sphere is 3.60 cm. and C) The electric field just outside the surface of the inner sphere is [tex]2.36 * 10^6 V/m[/tex] (volts per meter).

To calculate the capacitance, we can use the formula C = Q/V, where Q is the charge and V is the potential difference. Plugging in the values, we get [tex]C = (3.20 * 10^{-9} C)/(250 V) = 1.28 * 10^{-11} F[/tex].

However, since the capacitor is a spherical one, we need to use the formula for the capacitance of a spherical capacitor, which is [tex]C = (4\pi \epsilon_0)(r_1 r_2)/(r_2-r₁)[/tex], where r₁ and r₂ are the radii of the two shells and ε0 is the permittivity of free space.

Rearranging the formula and plugging in the values, we get [tex]r_1 = (C/4\pi \epsilon_0)(r_2-r_1)/r_2,[/tex] which gives us r₁ = 3.60 cm.

To calculate the electric field just outside the surface of the inner sphere, we can use the formula

E = [tex]\frac{Q}{4\pi\epsilon_0 r^2}[/tex], where r is the radius of the inner sphere.

Plugging in the values, we get [tex]E = (3.20 * 10^{-9} C)/(4\pi\epsilon_0(0.0460 m)^2) = 2.36 * 10^6 V/m.[/tex]

This electric field arises due to the charge on the inner sphere and induces an opposite charge on the outer shell of the capacitor.

To know more about spherical capacitor, refer here:

https://brainly.com/question/15550772#

#SPJ11

Unproven theories ultimately cannot be regarded as scientific facts or principles and are not generally recognised by the scientific community.

A well-supported explanation of a natural occurrence in science that has passed rigorous examination and is backed by empirical data is referred to as a theory. A hypothesis, however, cannot be regarded as a scientific fact or principle if it is not backed up by empirical data or if it has not undergone extensive testing and verification. The scientific community frequently rejects unproven notions with scant empirical backing and may even label them as pseudoscientific or non-scientific. This is so that scientific theories and findings may be evaluated and verified frequently. Science does this by using evidence-based reasoning and critical thinking. Unproven theories are therefore eventually not regarded as being a part of the corpus of scientific knowledge.

learn more about theories here:

https://brainly.com/question/1759635

#SPJ4

Given equal-sized samples (volumes) of galena and quartz, the Galena sample will feel heavier because of its higher specific gravity. Thus, the correct option is A.

Specific gravity is the ratio of the density of a substance to the density of a standard substance in physics. It's typically applied to liquids and solids, but it may also be applied to gases. The most often utilized standard material for liquids and solids is water at 4°C. A substance's specific gravity is dimensionless and is often represented by the Greek symbol ρ.

Relative Density of the given substances:

Galena's specific gravity is 7.5, Quartz's specific gravity is 2.65, and Liquid mercury's specific gravity is 13.6. An object with a specific gravity greater than 1 sinks in water, while one with a specific gravity less than 1 floats in water. The specific gravity of water is 1.0. An object with a specific gravity greater than 1 sinks in water, while one with a specific gravity less than 1 floats in water.

We can conclude from the values above that liquid mercury is heavier than galena, which is in turn heavier than quartz. Therefore, since both quartz and galena are being measured with equal sizes or volumes, galena will feel heavier than quartz.

Therefore, the correct option is A.

Learn more about Specific gravity here:

https://brainly.com/question/9100428

#SPJ11

Of the three states of matter (solid, liquid, and gas), gas has the most kinetic energy. This is because the particles in a gas have the highest average speed compared to the particles in solids and liquids.

In a gas, the particles are in constant motion, colliding with each other and the walls of the container. This motion generates kinetic energy, which is proportional to the speed and mass of the particles. In contrast, solids have the lowest kinetic energy because their particles are tightly packed and have limited movement. The particles in a solid vibrate around a fixed position, and only experience small oscillations. Liquids have an intermediate amount of kinetic energy. The particles in a liquid are less tightly packed than in a solid, and can move more freely, resulting in more kinetic energy. However, liquids have more intermolecular forces between the particles compared to gases, which restricts their movement and reduces their average speed. Therefore, of the three states of matter, gases have the most kinetic energy, followed by liquids and then solids.

Learn more about kinetic energy here:

https://brainly.com/question/26472013

#SPJ4

The researcher's observation that more auxin collects in the sides of stems and roots that are not exposed to light is likely due to the phenomenon of phototropism.

In the process of phototropism, light influences the direction and rate of growth of plant cells. In particular, light induces the cells on one side of a stem or root to create less auxin than the cells on the shaded side. Less auxin is produced on the lighted side and more auxin is produced on the shaded side as a result. The hormone auxin is essential for controlling the growth and development of plants. Auxin generally promotes cell growth and elongation at greater concentrations while inhibiting cell elongation at lower concentrations. Since the cells on the lighted side of the stem or root will contain less auxin when there is light.

Learn more about auxin here:

https://brainly.com/question/21591280

#SPJ4

Answer:

4 km/hr^2

Explanation:

We can use the formula for acceleration:

a = (v_f - v_i) / t

where:

a = acceleration

v_f = final velocity

v_i = initial velocity

t = time taken

Substituting the given values, we get:

a = (70 km/hr - 50 km/hr) / 5 hr

a = 20 km/hr / 5 hr

a = 4 km/hr^2

The maximum gain of an amplifier that produces an output voltage amplitude of 50 Vpp with an input voltage amplitude of 200 mVpp is 25. The formula to calculate gain is output voltage amplitude divided by input voltage amplitude.

In this case, we are given an input voltage of 200 mVpp, so the maximum gain of this amplifier can be calculated as follows:

Gain = Output Voltage/Input Voltage = Output Voltage/200 mVpp

Therefore, the maximum gain of this amplifier is equal to the output voltage. In other words, the maximum gain of this amplifier is equal to the voltage output of the amplifier.

To calculate the output voltage of the amplifier, we need to know the supply voltage and the resistance of the load. Assuming the supply voltage is 5V and the load resistance is 10k ohms, the output voltage can be calculated as follows:

Output Voltage = Supply Voltage * Load Resistance / (Load Resistance + Output Resistance) = 5V * 10k ohms / (10k ohms + 10k ohms) = 5V

Therefore, the maximum gain of this amplifier is 5V/200 mVpp = 25.

To summarize, the maximum gain of this amplifier is 25, calculated by dividing the output voltage by the input voltage. The output voltage can be calculated by knowing the supply voltage and load resistance.

For more such questions on Maximum voltage gain.

https://brainly.com/question/31086456#

#SPJ11

A change in velocity in short period of time means the acceleration is large, hence the net force must be proportionately large as well.

A force is a physical quantity that induces a body to undergo an alteration in speed, direction of motion, or shape. A force can be classified as a push or a pull. When forces are equal, the forces are balanced and the object is not moving. Otherwise, if the forces are not equal, making it unbalanced will not give the object any movement.

The force that induces the change in the speed or direction of an object is referred to as a net force. The net force is equal to the product of the mass of the object and its acceleration. Newton (N) is the unit of measurement for force.

When a ball bounces against a wall, there will be a large change in velocity in a short period of time. This means the acceleration is large, hence the net force must be proportionately large as well.

Learn more about acceleration here: https://brainly.com/question/26408808

#SPJ11

In the case where the car is traveling in the -x direction and decreasing in speed, it has a negative velocity and a positive acceleration. Therefore, option D is the correct answer. In this case, the car is traveling in the - direction and decreasing in speed. Therefore, it has a negative velocity and a positive acceleration.

Let's discuss the given options one by one:

(A) In this case, the car is traveling in the -x direction at a constant speed. Therefore, it has a negative velocity and zero acceleration. This option is incorrect.

(B) In this case, the car is traveling in the - direction and increasing its speed. Therefore, it has a negative velocity and a positive acceleration. However, the given direction is not specified, and thus this option is not accurate.

(C) In this case, the car is traveling in the +x direction and increasing in speed. Therefore, it has a positive velocity and a positive acceleration. This option is incorrect.

(D) In this case, the car is traveling in the - direction and decreasing in speed. Therefore, it has a negative velocity and a positive acceleration. This option is correct.

(E) In this case, the car is traveling in the +x direction and decreasing in speed. Therefore, it has a positive velocity and a negative acceleration. This option is incorrect.

Therefore, Option D ( - direction decreasing in speed) is correct.

To know more about negative velocity and positive acceleration, refer here:

https://brainly.com/question/12015984#

#SPJ11

The battery has to supply more power when two resistors are connected in series than when only one resistor is connected. This is because the power dissipated in a series circuit is equal to the sum of the power dissipated in each resistor.

When two identical resistors are connected in series to a battery, the battery has to supply more power than when only one of the resistors is connected. This is because the resistors offer resistance, which results in the dissipation of energy as heat. The higher the resistance of a resistor, the more power it requires to operate.Resistors consume energy as they offer resistance to the flow of current. The power supplied by the battery is converted to heat energy in the resistor, and the amount of heat energy dissipated is determined by the resistance of the resistor. The greater the resistance of the resistor, the more power it requires to function.

As a result, when two identical resistors are connected in series to a battery, the battery has to supply more power than when only one of the resistors is connected, to produce the same current through the circuit. Therefore, if two resistors of equal value are connected in series, the total power dissipated is twice that of when a single resistor is connected.

Read more about resistors :

https://brainly.com/question/13606415

#SPJ11

A maintenance expenditure should be capitalized if it increases the salvage value of the asset or extends the useful life of the asset.

An expenditure is a payment made in return for a product or service. Capital expenditure is money spent by a company on long-term assets like equipment and buildings.

Capitalizing refers to recording a cost or expense on the balance sheet for a future period rather than recognizing it immediately in the current period.

Capitalizing expenditure means the company will recognize the expenditure as an asset, which will be amortized over its useful life as opposed to expenses in the current period.

Therefore, a maintenance expenditure should be capitalized if the expenditure increases the extends the useful life of the asset.

Learn more about expenditure here:

https://brainly.com/question/935872

#SPJ11

The kinetic energy of the trunk increases by ½ mvf² = ½ m(10.65 m/s)²= 71.44 J during the displacement.

Net work = ΔK

W = Fd cosθ

W1 = F1d cosθ = (5.86 N)(3.010 m) cos(67.8°) = 6.99 J

W2 = F2d cosθ = (9.180 N)(3.010 m) cos(67.8°) = 10.97 J

W3 = F3d cosθ = (3.850 N)(3.010 m) cos(67.8°) = 4.58 J

Net work = W1 + W2 + W3 = 6.99 J + 10.97 J + 4.58 J = 22.54 J

Therefore, the net work done on the trunk by the three forces is 22.54 J.

ΔK = ½ mvf² - ½ mvi²

Since the trunk moves a distance of 3.010 m and is initially at rest, we can use the equation:

vf² = 2ad

where a is the acceleration of the trunk, which is given by:

a = ΣF / m

where ΣF is the net force on the trunk, which we can find using:

ΣF = F1 + F2 + F3

ΣF = (5.86 N + 9.180 N + 3.850 N) = 18.89 N

Therefore, the acceleration of the trunk is:

a = ΣF / m = 18.89 N / m

Since the trunk moves leftward, the acceleration is also leftward, so we can use a negative value for a.

Substituting the values for a and d, we get:

vf² = -2(-18.89 N / m)(3.010 m) = 113.51 (m/s)²

Taking the square root, we get:

vf = 10.65 m/s

Therefore, the change in kinetic energy of the trunk is:

ΔK = ½ mvf² - ½ mvi² = ½ m(10.65 m/s)²- 0 = ½ mvf²

Kinetic energy is a type of energy that an object possesses by virtue of its motion. It is defined as the energy an object has due to its motion and is proportional to the mass of the object and the square of its velocity. The formula for kinetic energy is KE = 1/2mv^2, where m is the mass of the object and v is its velocity.

Kinetic energy is a scalar quantity and has units of joules in the International System of Units (SI). It is a fundamental concept in physics and is used to describe many physical phenomena, including the motion of particles, the behavior of gases, and the motion of waves. In many cases, kinetic energy can be transformed into other forms of energy. For example, when a ball is thrown upwards, its kinetic energy is gradually converted into gravitational potential energy as it moves higher and higher.

To learn more about Kinetic energy visit here:

brainly.com/question/26472013

#SPJ4

The Periodic Table of Elements served as the inspiration for this scavenger hunt. The exercise consists of two sets of questions, each of which has 28 questions that must be answered using the Periodic Table.

Students are tasked with identifying elements in the first set of questions using information from their attributes, such as the element's position on the periodic table, atomic mass, or quantity of electrons, protons, or neutrons. The objectives of the questions are to familiarise students with the properties of various elements and the structure of the Periodic Table. The second series of questions is comparable to the first, but more difficult because it asks students to identify components using less obvious cues, like their chemical symbol or a chemical formula. In order to succeed in their future studies of chemistry and other related sciences, students will benefit from being more familiar with the structure of the periodic table and the characteristics of various elements.

learn more about Periodic Table here:

https://brainly.com/question/11155928

#SPJ4

The angular acceleration of the fan is 0.740 rad/s^2,

Angular acceleration which represents the rate at which the angular velocity changes over time. The unit used to measure angular acceleration is radians per square second (rad/s2), according to the International System of Units. The Greek alphabet symbol alpha (α) is used to denote angular acceleration.

To calculate the angular acceleration of the fan, the formula α = Δω/Δt is used. Here, α represents angular acceleration, Δω represents the change in angular speed, and Δt represents the change in time.

In this scenario, Δω is equal to 10.0 - 6.30 = 3.70 rad/s, and Δt is equal to 5.00 s. By substituting these values into the formula, we obtain α = 3.70/5.00 = 0.740 rad/s^2.

To gain more knowledge about angular acceleration, refer to brainly.com/question/21278452.

#SPJ11

Ceteris paribus, a decrease in capital productivity is the event that would cause both the equilibrium interest rate and the equilibrium quantity of investment to fall. The correct answer is option C.

Ceteris paribus is a Latin expression that means "all other things being equal." Ceteris paribus is a model in which economists use to analyze the effect of one independent variable on a dependent variable while keeping all other independent variables constant. This implies that only one variable is allowed to change while all other variables are held constant at their current level or position.

Therefore, Ceteris paribus, an increase in investor confidence, an increase in cosmetic income and wealth, and a strength of time preference will not cause both the equilibrium interest rate and the equilibrium quantity of investment to fall. However, a decrease in capital productivity is an event that would cause both the equilibrium interest rate and the equilibrium quantity of investment to fall.

When capital productivity is low, firms are unable to produce goods and services efficiently, and as a result, the demand for investment falls. When the demand for investment falls, the equilibrium quantity of investment will also decrease, leading to a decrease in the equilibrium interest rate.

To know more about Ceteris paribus, refer here:

https://brainly.com/question/13864080#

#SPJ11

Answer:

The four planets were approximately aligned on one side of the Sun and we used the gravity of each planet to speed up the spacecraft to get to the next one in its path

Explanation:

All the Options 1, 2, 3, 4  are true about the Voyager 2 spacecraft to make a "tour" of all four of the jovian planets in the late 1970's and the 1980's.

The Voyager 2 spacecraft was able to make a "tour" of all four of the jovian planets in the late 1970's and the 1980's due to the following:

Learn more about "NASA and spacecraft" at: https://brainly.com/question/16538247

#SPJ11

"The colours on an oil slick are caused by reflection and interference." Correct option is B.

Different bands of the oil slick create different colours as the oil film progressively thins from the centre to the edges.

Interference is what gives an oil slick drifting on water or a soap bubble in the sun their vibrant colours. The colours that interact most positively are the ones that are most vibrant. Thin film interference is the name given to the phenomenon because it occurs when light reflected from various thin film surfaces interferes with one another.

The most crucial interfering principle is the superposition principle.

This hair colour procedure primarily uses jewel tones and rainbow colours, including burgundy, royal blue, deep purple, green, and deep red. Alternating the colours that give your hair an oil spill appearance is the best method to make your skin tone and hair look good together. Best choice is B.

To know more about interference:

https://brainly.com/question/1463425

#SPJ4

Answer: The motion of a body with constant speed in a circular path is said to be accelerated, because it is moving with uniform speed, but not with uniform velocity, as velocity is a vector quantity, it can be represented in magnitude as well the direction.

Explanation:

If a tsunami warning is issued for the island, they will have approximately 11.7 hours before the waves arrive.

What is Magnitude?

Magnitude is a measure of the strength or intensity of a physical quantity or phenomenon, such as an earthquake or a sound wave. It is often expressed using a numerical scale, with higher values indicating greater strength or intensity. In the case of earthquakes, magnitude is typically measured using the Richter scale or the moment magnitude scale, which take into account the amplitude of seismic waves and the energy released by the earthquake.

To calculate the time it takes for a tsunami to travel from Japan to the island, we can use the following formula:

t = (2 * pi * d) / g * ln(1 + sqrt(h/d))

where t is the time it takes for the tsunami to travel, d is the average water depth, h is the wave height, and g is the acceleration due to gravity (9.8 m/s^2).

Magnitude of the earthquake: 8.5

Wavelength of the tsunami: 200 km = 200,000 m

Average water depth: 4,900 m

To calculate the wave height, we can use the following formula:

h = (M / 5) * (D / 10)^1/2

where M is the magnitude of the earthquake and D is the distance between the earthquake epicenter and the observation point (in this case, the island). Note that this formula is an approximation and may not be accurate for all cases.

Using the given values, we get:

D = 8,000 km = 8,000,000 m

h = (8.5 / 5) * ((8,000,000 / 10)^1/2) = 2,738.6 m

Substituting these values into the formula for t, we get:

t = (2 * pi * 4,900) / 9.8 * ln(1 + sqrt(2,738.6/4,900)) = 11.7 hours

Learn more about Magnitude from given link

https://brainly.com/question/24468862

#SPJ1

The wavelength of the radio waves is approximately 0.579 m or 57.9 cm

Wavelength is the distance covered by an electromagnetic wave while propagating through space. The relationship between the wavelength and the frequency of an electromagnetic wave is given by the formula;

Wavelength = speed of light / frequency = c / f

where c is the speed of light and f is the frequency of the wave.

To calculate the wavelength of a VHF television station assigned to channel 22 that transmits its signal using radio waves with a frequency of 518 MHz, we substitute the known values into the equation above.

Wavelength = c / f = (3 x 10⁸ m/s) / (518 x 10⁶ Hz) = 0.579 m or 57.9 cm (rounded to three significant digits)

Therefore, the wavelength of the radio waves transmitted by the VHF television station assigned to channel 22 is 0.579 m or 57.9 cm (rounded to three significant digits).

Learn more about wavelength here: https://brainly.com/question/10728818.

#SPJ11

The translational speed of the cylinder when it reaches the foot of the incline is approximately 9.43 m/s.

We can use conservation of energy to solve this problem. The initial energy of the cylinder is all potential energy, and the final energy is all kinetic energy. The potential energy at the bottom of the incline is zero.

The potential energy of the cylinder at the top of the incline is given by:

PE = mgh

where m is the mass of the cylinder, g is the acceleration due to gravity, and h is the height of the incline. Substituting the given values, we get:

PE = (mass of cylinder) x (acceleration due to gravity) x (height of incline) = mgh

The kinetic energy of the cylinder at the bottom of the incline is given by:

KE = (1/2)mv^2

where v is the translational speed of the cylinder at the bottom of the incline.

According to the conservation of energy, the initial potential energy is equal to the final kinetic energy, so we can set these two expressions equal to each other:

mgh = (1/2)mv^2

We can cancel the mass of the cylinder from both sides, and solve for v:

v = sqrt(2gh)

Substituting the given values, we get:

v = sqrt(2 x 9.81 m/s^2 x 7.20 m) ≈ 9.43 m/s

Therefore, the translational speed of the cylinder when it reaches the foot of the incline is approximately 9.43 m/s.

For more such questions on Cylinder

https://brainly.com/question/23935577

#SPJ11

Isometric pushes against a wall made of concrete, Isotonic running up a hill. isotonic freestyle swimming, bicycle pedalling on a level surface: isotonic.

Static muscle contractions, in which the length of the muscle does not change during the workout, are called isometric exercises. This indicates that during the activity, there is no discernible movement or alteration in joint angle. Instead, the muscles are tense against a constant force or maintained still for a certain period of time. Exercises that are isometric include pushing against a wall, keeping a plank position, and tightening a hand grasp. Exercises that are isometric can help to increase joint stability and balance as well as muscular strength and endurance. They can also be incorporated into normal workout routines for general health and strength training. They are frequently used in physical therapy to aid patients in recovering from injuries or surgery.

Learn more about Isometric here:

https://brainly.com/question/17102666

#SPJ4

Force will become  2.25 x 10^N. because, According to Coulomb's Law, the force between two point charges is directly proportional to the product of their charges and inversely proportional to the square of the distance between them.

Thus, if the distance between two point charges is doubled, the force between them will decrease by a factor of 4. This is because the inverse square relationship means that the force decreases rapidly with distance. Therefore, if the force between two point charges is 9 x 10^N when they are 1 meter apart, when the distance is doubled to 2 meters, the force will become 9 x 10^N / 4 = 2.25 x 10^N.

To know more about  Coulomb's Law, here

brainly.com/question/506926

#SPJ4

The maximum energy of photoelectrons from aluminium is 2.3 eV for radiation of 2000 Å and 0.90 eV for radiation of 3130 Å.

To calculate Planck's constant and the work function of aluminium, we need to use the equation:

 h = E2 - E1/ λ2 - λ1

Where h is Planck's constant, E1 and E2 are the maximum energy of photoelectrons for each wavelength, and λ1 and λ2 are the wavelengths.

Using the given data, we have:

h = (2.3 - 0.90) / (2000 - 3130)

Therefore, h = -1.4 eV / -930 Å, which simplifies to h = 0.0015 eVÅ.

The work function of aluminium is equal to the maximum energy of the photoelectrons for the longest wavelength, in this case, 0.90 eV. Therefore, the work function of aluminium is 0.90 eV.

Learn more  about photoelectrons  at brainly.com/question/16772624

#SPJ11

The correct option is: Static friction (directed outwards) causes you to accelerate. (Option C)

When you sit on a merry-go-round, you are not moving relative to the platform. Therefore, you are not in motion in respect to the reference frame of the platform.

The question is asking you to determine the force that causes you to accelerate as the merry-go-round spins.

Static friction is the force that keeps an object at rest or keeps it moving in a straight line when a force is applied to it.

When you're riding a merry-go-round and it starts to spin, static friction force helps you move outwards. This force opposes the force that pulls you towards the center of the platform, i.e., centripetal force.

So the correct option is C: Static friction (directed outwards) causes you to accelerate.

To know more about "Static friction" refer here:

https://brainly.com/question/13828735#

#SPJ11

A particle's velocity is described by the function vx=kt2 , where vx is in m/s , t is in s , and k is a constant. The particle's position at t0=0s is x0 = -5.40 m. At t1 = 2.00 s , the particle is at x1 = 5.80 m. The value of k is 2.80 m/s2.

The given equation describes the velocity of a particle in terms of a constant, k, and time, t. The velocity, vx, is given in m/s. The initial position of the particle at t0=0s is x0=-5.40 m, and at t1=2.00 s the particle is at x1=5.80 m. To find the value of the constant k, we can solve the equation for the change in velocity Δvx.

Δvx = vx1 – vx0 = k(t12 – t02)
Δvx = 5.80 – (-5.40) = 11.20 m/s

k = (11.20 m/s) / (2.002 s2) = 2.80 m/s2

Now that we have found the value of the constant k, we can use it to find the velocity of the particle at any time t. For example, at t2=4.00 s the velocity of the particle is vx2=11.20 m/s. This can be calculated using the equation vx2 = k(t22) = 2.80(4.002) = 11.20 m/s.

From the velocity equation, we can also calculate the position of the particle at any time t. The position of the particle at t2=4.00 s is x2= 11.20(4.00) = 44.80 m. We can also calculate the position of the particle at any other time t, by simply substituting in the corresponding value of t into the equation.

In conclusion, the equation vx = kt2 describes the velocity of a particle in terms of a constant, k, and time, t. Using this equation, we can calculate the velocity and position of the particle at any given time.

For more such questions on Velocity.

https://brainly.com/question/14528397#

#SPJ11

Complete Question:

A particle’s velocity is described by the function vx = [tex]kt^2m/s[/tex], where k is a constant and t is in s. The particle’s position at [tex]t_0[/tex] = 0s is [tex]x_0[/tex] = -5.40 m. At [tex]t_1[/tex] = 2.00 s, the particle is at [tex]x_1[/tex] = 5.80 m. Determine the value of the constant k. Be sure to include the proper units