Two long straight wires are suspended vertically. The wires are connected in series, and a current from a battery is maintained in them. What happens to the wires? What happens if the battery is replaced by an a-c source?
Answer:
(i) When a battery is connected inseries to two long parallel wires, the currents in the two wires will be in opposite directions. Due to which a force of repulsion will be acting between them and they are moving further apart.
(ii) When a battery is connected in parallel to two long parallel wires, the currents in the two wires will be in same direction. Due to it, a force of attraction will be acting between them and they are coming closer to each other.
hope it's help you ....!!!!!
plz mark as brain list and follow me #rishu...!!!!
Explanation:
Hope it will helps you lot!
Two circular coils are concentric and lie in the same plane.The inner coil contains 120 turns of wire, has a radius of 0.012m,and carries a current of 6.0A. The outer coil contains 150turns and has a radius of 0.017 m. What must be the magnitudeand direction (relative to the current in the inner coil) ofthe current in the outer coil, such that the net magnetic field atthe common center of the two coils is zero?
Answer:
[tex]I_2=6.8A[/tex]
Explanation:
From the question we are told that:
Turns of inner coil [tex]N_1=120[/tex]
Radius of inner coil [tex]r_1=0.012m[/tex]
Current of inner coil [tex]I_1=6.0A[/tex]
Turns of Outer coil [tex]N_2=150[/tex]
Radius of Outer coil [tex]r_2=0.017m[/tex]
Generally the equation for Magnetic Field is mathematically given by
[tex]B =\frac{ \mu N I}{2R}[/tex]
Therefore
Condition for the net Magnetic field to be zero
[tex]\frac{N_1* I_1}{( 2 * r_1 )}=\frac{N_2 * I_2}{2 * r_2}[/tex]
[tex]I_2=\frac{(N_1* I_1)*(( 2 * r_2)}{( 2 * r_1)*N_2}[/tex]
[tex]I_2=\frac{(120*6.0)*(( 2 * 0.017)}{( 2 * 0.012)*150}[/tex]
[tex]I_2=6.8A[/tex]
Consider a 200-ft-high, 1200-ft-wide dam filled to capacity. Determine (a) the hydrostatic force on the dam and (b) the force per unit area of the dam near the top and near the bottom. Note: we will see that the resultant hydrostatic force will be
Answer:
a) [tex]F_g=1.5*10^9Ibf[/tex]
b) [tex]F_t=12490Ibf/ft^2[/tex]
[tex]F_b=0[/tex]
Explanation:
From the question we are told that:
Height [tex]h=200ft[/tex]
Width [tex]w=1200ft[/tex]
a)
Generally the equation for Dam's Hydro static force is mathematically given by
[tex]F_g=\rho*g*\frac{h}{2}(w*h)[/tex]
Where
[tex]\rho=Density\ of\ water[/tex]
[tex]\rho=62.4Ibm/ft^3[/tex]
Therefore
[tex]F_g=62.4*32.2*\frac{200}{2}(1200*200)[/tex]
[tex]F_g=1.5*10^9Ibf[/tex]
b)
Generally the equation for Dam's Force per unit area is mathematically given by
[tex]F=\rho*g*h[/tex]
For Top
[tex]F_t=\rho*g*h[/tex]
[tex]F_t=62.4*32.2*200[/tex]
[tex]F_t=12490Ibf/ft^2[/tex]
For bottom
[tex]Here \\H=0 zero[/tex]
Therefore
[tex]F_b=0[/tex]
The hydrostatic force on the dam is [tex]2.995 \times 10^9 \ lbF[/tex].
The force per unit area near the top is 86.74 psi.
The force per unit area near the bottom is zero.
Hydrostatic force
The hydrostatic force on the dam is the force exerted on the dam by the column of the water.
[tex]F = PA\\\\F = (\rho gh) \times (wh)\\\\F = (62.4 \times 32.17 \times 200) \times (1200 \times 200)\\\\F = 9.636 \times 10^{10} \ lb-ft/s^2\\\\1 \ lbF = 32.17\ lb-ft/s^2\\\\F = 2.995 \times 10^9 \ lbF[/tex]
Force per unit area near the topThe force per unit area is the pressure exerted near the top of the dam.
[tex]P = \rho gh\\\\P = 0.052 \times \rho h[/tex]
where;
P is pressure in PSI
ρ is density of water in lb/gal
h is the vertical height in ft
[tex]P = 0.052 \times 8.34 \times 200\\\\P = 86.74 \ Psi[/tex]
The pressure near the bottom is zero, become the vertical height is zero.
Learn more about hydrostatic pressure here: https://brainly.com/question/11681616
Two different galvanometers G1 and G2, have internal resistances r1and r2. The galvanometers G1 and G2 require the same current IC1=IC2 for a full-scale deflection of their pointers. These galvanometers G1 and G2 are used to build lab-made ammeters A1 and A2 . Both ammeters A1 and A2 have the same maximum scale reading Imax1=Imax2=Imax. To build A1 ,shunt resistor of resistance Rsh1is used and to build A2 , shunt resistor of resistance Rsh2 is used. The value of these shunt resistor resistances are such that: Rsh1=3Rsh2. What is the ratio oftheir internal resistances: r1:r2?
Answer:
there are 3 photos attached. so check
Explanation:
A race car goes from a complete stop at the start line to 150 miles per hour in 5 seconds. What is its acceleration? Show your work.
Answer:
Explanation:
150/5 = 30
30mph per 1 second
True or false : conservation of energy gives a relationship between the speed of a falling object and the height from which it was dropped
Answer:
truee
Explanation:
elastic wire extend by 1.ocm when a load on 20g range from It, what additional load will it be required Cause the futher extension of 2.0cm
Answer:
40g
Explanation:
20g range > 1.0cm
Therefore,
40g range > 2.0cm
One charge is fixed q1 = 5 µC at the origin in a coordinate system, a second charge q2 = -3.2 µC the other is at a distance of x = 90 m from the origin.
What is the potential energy of this pair of charges?
Answer:
5.4uC
Explanation:
Derive the dimension of coefficient of linear expansivity
Answer:
The SI unit of coefficient of linear expansion can be expressed as °C-1 or °K-1. ... The dimension of coefficient of linear expansion will be M0L0T0K−1.
A cylindrical wire made of an unknown alloy hangs from a support in the ceiling. You measure the relaxed length of the wire to be 16 m long; and the radius of the wire to be 3.5 m. When hang a 5 kg mass from the wire, you measure that it stretches a distance of 4 x 10 m The average bond length between atoms is 2.3 x 10^0 m for th alloy.
Required:
What is the stiffness of a typical interatomic bond in the alloy
Answer: hello some of your values are wrongly written hence I will resolve your question using the right values
answer:
stiffness = 1.09 * 10^-6 N/m
Explanation:
Given data:
Length ( l ) = 16 m
radius of wire ( r ) = 3.5 m
mass ( m ) = 5kg
Distance stretched ( Δl ) = 4 * 10^-3 m ( right value )
average bond length ( between atoms ) = 2.3 * 10^-10 m ( right value)
first step : calculate the area
area ( A ) = πr^2 = π * ( 3.5)^2 = 38.48 m^2
γ = MgL / A Δl
= [ (5 * 9.81 * 16 ) / ( 38.48 * (4.3*10^-3) ) ]
= 784.8 / 0.165 = 4756.36 N/m^2
hence : stiffness = γ * bond length
= 4756.36 * 2.3 * 10^-10 = 1.09 * 10^-6 N/m
a volcano that may erupt again at some time in the distant future is
Assume that a friend hands you a 10-newton box to hold for her. If you hold the box without moving it at a height of 10 meters above the ground, how much work do you do
Answer:
100 Joules
Explanation:
Applying,
W = mgh................... Equation 1
Where W = workdone to hold the box above the ground, mg = weight of the box, h = height of the box.
From the question,
Given: mg = 10 newtons, h = 10 meters.
Substitute these values into equation 1
W = 10×10
W = 100 Joules.
Hence the amount of workdone is 100 Joules
A surveyor measures the distance across a straight river by the following method: Starting directly across from a tree on the opposite bank, he walks x = 106 m along the riverbank to establish a baseline. Then he sights across to the tree. The angle from his baseline to the tree is = 32.8°. How wide is the river?
Answer:
x = 68.3 m
Explanation:
tan 32.8 = x / 106
krichoffs law of current questions
Answer:
Explanation:
Kirchhoff's Current Law, often shortened to KCL, states that “The algebraic sum of all currents entering and exiting a node must equal zero.
#I AM ILLITERATE
g Light that is incident upon the eye is refracted several times before it reaches the retina. As light passes through the eye, at which boundary does most of the overall refraction occur?
Answer
Explanation
:giác mạc
a standard bathroom scale is placed on an elevator. A 34 kg boy enters the elevator on the first floor and steps on the scale. What will the scale read (in newtons) when the elevator begins to accelerate upward at 0.4 m/s2
Answer:F = 255 N
Explanation:
It is given that,
Mass of the boy, m = 25 kg
Acceleration of the elevator,
The elevator is accelerating in upward direction. The net force acting on the boy is given by :
g is the acceleration due to gravity
F = 255 N
The scale reading is 255 N as it begins to accelerate upward. hence, this is the required solution.
For example, we can take Water
In (A) Water has same mass and great volume
In (B) Water has same mass and lower volume
Will there be any change in its density then?
Answer:
yes there will be change in its density
What is science?Give two examples of living beings?
Answer:
the study of the past
Explanation:
dogs and cats
potential diffetence
Answer:
6v
Explanation:
V=IR
V= 2* 3
V= 6 volts
The cart travels the track again and now experiences a constant tangential acceleration from point A to point C. The speeds of the cart are 11.0 ft/s at point A and 18.0 ft/s at point C. The cart takes 5.00 s to go from point A to point C, and the cart takes 1.30 s to go from point B to point C. What is the cart's speed at point B
Answer:
The speed at B is 16.18 ft/s .
Explanation:
Speed at A, u = 11 ft/s
Speed at C, v' = 18 ft/s
Time from A to C = 5 s
Time from B to C = 1.3 s
Let the speed of car at B is v.
Let the acceleration is a.
From A to B
Use first equation of motion
v = u + a t
18 = 11 + a x 5
a = 1.4 ft/s^2
Let the time from A to B is t' .
t' = 5 - 1.3 = 3.7 s
Use first equation of motion from A to B
v = 11 + 1.4 x 3.7 = 16.18 ft/s
Choose one. 5 points
Use the equation from week 3:
frequency =
wavespeed
wavelength
and the wavelength you found in #3 to calculate the frequency of this photon (remember the speed of
light is 3E8 m/s);
7.6E14 Hz
6.0E14 Hz
4,6E14 Hz
The frequency is 4,6E14 Hz.
What is the frequency?
Frequency is the fee at which modern changes direction in step with 2nd. it's far measured in hertz (Hz), a worldwide unit of degree wherein 1 hertz is identical to 1 cycle in line with 2d. Hertz (Hz) = One hertz is the same as 1 cycle in step with the second. Cycle = One entire wave of alternating present-day voltage.
Frequency describes the number of waves that pass a hard and fast place in a given quantity of time. So if the time it takes for a wave to skip is half of 2d, the frequency is 2 per 2nd. If it takes 1/one hundred of an hour, the frequency is a hundred in step with hour.
Learn more about frequency here:-https://brainly.com/question/254161
#SPJ2
Electromagnetic radiation with a wavelength of 525 nm appears as green light to the human eye. Calculate the frequency of this light. Be sure to include units in your answer.
Answer:
5.71×10¹⁴ Hz
Explanation:
Applying,
v = λf................. Equation 1
Where v = speed of the electromagnetic radiation, λ = wavelength of the electromagnetic radiation, f = frequency
make f the subject of the equation
f = v/λ............. Equation 2
From the question,
Given: λ = 525 nm = 5.25×10⁻⁷ m,
Constant: Speed of electromagnetic wave (v) = 3.0×10⁸ m/s
Substitute these values into equation 2
f = (3.0×10⁸)/(5.25×10⁻⁷)
f = 5.71×10¹⁴ Hz
Hence the frequency of light is 5.71×10¹⁴ Hz
In the diagram, the crest of the wave is show by:
A
B
C
D
Answer:
D.
Explanation:
The crest of a wave refers to the highest point of a wave. This is illustrated by D.
A large metal sphere has three times the diameter of a smaller sphere and carries three times the charge. Both spheres are isolated, so their surface charge densities are uniform. Compare (a) the potentials (relative to infinity) and (b) the electric field strengths at their surfaces.
Answer:
A. Equals to that of the smaller sphere
B. 3 times less than that of the smaller sphere
Explanation:
(a) Equals to that of the smaller sphere
The potential of an isolated metal sphere, with charge Q and radius R, is kQ=R, so a sphere with charge 3Q and radius 3R has the same potential
b) 3 times less than that of the smaller sphere
However, the electric field at the surface of the smaller sphere is ?=? 0 = kQ=R2 , so tripling Q and R reduces the surface field by a factor of 1/3
Earth’s Moon has a diameter of 3,474 km and orbits at an average distance of 384,000 km. At that distance it subtends and angle just slightly larger than half a degree in Earth’s sky. Pluto’s moon Charon has a diameter of 1,186 km and orbits at a distance of 19,600 km from the dwarf planet. Compare the appearance of Charon in Pluto’s skies with the Moon in Earth’s skies. Describe where in the sky Charon would appear as seen from various locations on Pluto.
The reason for arriving at the above solutions is as follows:
The given dimensions and distance from the Earth of the Moon are;
The diameter of the Moon, d = 3,474 km
The average distance of the Moon from the Earth, R = 384,000 km
Required:
The comparison between Charon's appearance in Pluto and the Moon's appearance on Earth Earth
Solution:
The distance of the Moon's travels in an orbit, C = 2·π·R
∴ C = 2 × π × 384,000 km
The angle subtended by the Moon, θ = d/C × 360°
∴ θ = 3,474/(2 × π × 384,000) × 360° ≈ 0.518°
Pluto's moon Charon, has the following parameters;
The diameter of the Charon, d₂ = 1,186 km
The average distance of the Charon from Pluto, R₂ = 19,600 km
Therefore, the distance of the Moon's travels in an orbit, C₂ = 2·π·R₂
∴ C₂ = 2 × π × 19,600 km
The angle subtended by the Moon, θ₂ = d₂/C₂ × 360°
∴ θ₂ = 1,186/(2 × π × 19,900) × 360° ≈ 3.415°
The angle subtended by Charon in Pluto's sky ≈ 3.415°
Charon therefore, appears 7 times larger in Pluto's skies than the Moon's appearance in Earth's skies
Required:
The appearance of Charon as seen from different locations on Pluto
Solution:
Charon is gravitationally locked to Pluto, therefore, the same side of Pluto is faced with the same side of Charon
Therefore;
Charon appears constantly overhead from the side of Pluto locked to CharonCharon appears constantly at the horizon from the poles on either side of the axis of rotation of Pluto and CharonLearn more about Pluto's moon Charon here:
https://brainly.com/question/3920772
https://brainly.com/question/21590852
https://brainly.com/question/17177801
Electron A is fired horizontally with speed 1.00 Mm/s into a region where a vertical magnetic field exists. Electron B is fired along the same path with speed 2.00 Mm/s. (i) Which electron has a larger magnetic force exerted on it
B will have the greater force
Fc=MV2 /R=Fm
The A particle has less centipetal force and larger radius so larger curve
A proton traveling at 17.6° with respect to the direction of a magnetic field of strength 3.28 mT experiences a magnetic force of 9.14 × 10-17 N. Calculate (a) the proton's speed and (b) its kinetic energy in electron-volts.
Answer:
a) The proton's speed is 5.75x10⁵ m/s.
b) The kinetic energy of the proton is 1723 eV.
Explanation:
a) The proton's speed can be calculated with the Lorentz force equation:
[tex] F = qv \times B = qvBsin(\theta) [/tex] (1)
Where:
F: is the force = 9.14x10⁻¹⁷ N
q: is the charge of the particle (proton) = 1.602x10⁻¹⁹ C
v: is the proton's speed =?
B: is the magnetic field = 3.28 mT
θ: is the angle between the proton's speed and the magnetic field = 17.6°
By solving equation (1) for v we have:
[tex]v = \frac{F}{qBsin(\theta)} = \frac{9.14 \cdot 10^{-17} N}{1.602\cdot 10^{-19} C*3.28 \cdot 10^{-3} T*sin(17.6)} = 5.75 \cdot 10^{5} m/s[/tex]
Hence, the proton's speed is 5.75x10⁵ m/s.
b) Its kinetic energy (K) is given by:
[tex] K = \frac{1}{2}mv^{2} [/tex]
Where:
m: is the mass of the proton = 1.67x10⁻²⁷ kg
[tex] K = \frac{1}{2}mv^{2} = \frac{1}{2}1.67 \cdot 10^{-27} kg*(5.75 \cdot 10^{5} m/s)^{2} = 2.76 \cdot 10^{-16} J*\frac{1 eV}{1.602 \cdot 10^{-19} J} = 1723 eV [/tex]
Therefore, the kinetic energy of the proton is 1723 eV.
I hope it helps you!
Light of a given wavelength is used to illuminate the surface of a metal, however, no photoelectrons are emitted. In order to cause electrons to be ejected from the surface of this metal you should: ___________
a. use light of the same wavelength but increase its intensity.
b. use light of a shorter wavelength.
c. use light of the same wavelength but decrease its intensity.
d. use light of a longer wavelength.
Answer:
use light of the same wavelength but decrease it's intensity
If a proton and electron both move through the same displacement in an electric field, is the change in potential energy associated with the proton equal in magnitude and opposite in sign to the change in potential energy associated with the electron?
a. The magnitude of the change is smaller for the proton.
b. The magnitude of the change is larger for the proton.
c. The signs Of the two changes in potential energy are opposite.
d. They are equal in magnitude.
e. The signs of the two changes in potential energy are the same.
Answer: They are equal in magnitude.
- The signs of the two changes in potential energy are opposite
Explanation:
When the proton and electron both move through the same displacement in an electric field, the change in potential energy that is associated with the proton is equal in magnitude.
Also, it should be noted that the signs of the two changes in potential energy are opposite.
Do you believe in ghost
Answer:
well its about our thinking but i do believe in ghost a little
