affect the amount and rate the alcohol reaches the
bloodstream.

Answer:

assuming factor of safety of 2  

Se = 118.858 MPa

Explanation:

Torque = ± 100 N m

length of solid round steel shaft = 1-m

Angular deflection = 2°

shear modulus of elasticity = 80 GPa

Calculate Fatigue strength of material

apply Von-miss effective stress rule to determine the Von mises stress  

max torque = 100 + 0

assuming a  factor of safety of 2  

Se(fatigue strength of material ) = Von mises stress * Fs

                                                     = 59.429 * 2 = 118.858 MPa

Answer:

the minimum power input required for this air-conditioning system is 1.20 hp

Explanation:

Given the data in the question;

Temperature inside ( Sink ) T[tex]_L[/tex] = 70°F = ( 70 + 460 )R = 530 R

temperature outside ( source )T[tex]_H[/tex] = 100°F = ( 100 + 460 )R = 560 R

[tex]Q_W[/tex] = 800 Btu/min

[tex]Q_L[/tex] = 100  Btu/min

Now, from the equation of coefficient of performance of refrigerator;

[tex]COP_{Ref[/tex] = Desired output / Required input

[tex]COP_{Ref[/tex] = [tex]Q_{out[/tex] / [tex]W_{net[/tex] --------- let this be equation 1

[tex]COP_{Ref[/tex] = ( [tex]Q_L + Q_W[/tex] ) / [tex]W_{net[/tex]

where [tex]Q_W[/tex] is the rate heat gained through the wall

[tex]Q_L[/tex] is the heat generation from people and lights and appliances.

Now, lets consider the equation coefficient of performance of refrigerator in terms of temperatures;

[tex]COP_{Ref[/tex] = [tex]T_L[/tex] / ( [tex]T_H[/tex] - [tex]T_L[/tex] )

we substitute

[tex]COP_{Ref[/tex] = 530 / ( 560 - 530 )

[tex]COP_{Ref[/tex] = 530 / 30

[tex]COP_{Ref[/tex] = 17.667

so we substitute into equation 1;

[tex]COP_{Ref[/tex] = [tex]Q_{out[/tex] / [tex]W_{net[/tex] ---------

[tex]COP_{Ref[/tex] = ( [tex]Q_L + Q_W[/tex] ) / [tex]W_{net[/tex]

17.667 = ( 100 + 800 ) / [tex]W_{net[/tex]

17.667 = 900 / [tex]W_{net[/tex]

[tex]W_{net[/tex] = 900 / 17.667

[tex]W_{net[/tex] = 50.94 Btu/min

[tex]W_{net[/tex] = ( 50.94 / 42.53 ) hp

[tex]W_{net[/tex] = 1.198 hp ≈ 1.20 hp

Therefore, the minimum power input required for this air-conditioning system is 1.20 hp

Answer:

the answer is equal to 2.5cos(4t +53.1)

Answer:

do you have to make the right decisions to be a person who has been a member who is not the first time a great person who has a job in a day of his life or

Answer:

Take a 3 to 8 decoder with active low outputs

Assuming you are familiar with the functioning of decoders,

The three inputs of decoder of course are the first, second and the carry bit which you feed to the subtractor.

Next we examine the truth table of the full subtractor i formatted in the picture.

Then write the minterms for the difference output and borrow output from the given truth table picture I have mentioned before!!

Explanation:

hopi it to help you!!

Answer:

All of the above

Explanation:

firstly, a creep can be explained as the gradual deformation of a material over a time period. This occurs at a fixed load with the temperature the same or more than the recrystallization temperature.

Once the material gets loaded, the instantaneous creep would start off and it is close to electric strain. in the primary creep area, the rate of the strain falls as the material hardens. in the secondary area, a balance between the hardening and recrystallization occurs. The material would get to be fractured hen recrstallization happens.  As temperature is raised the recrystallization gets to be more.

Answer:

The correct answer is "1341.288 W/m".

Explanation:

Given that:

T₁ = 300 K

T₂ = 500 K

Diameter,

d = 0.2 m

Length,

l = 1 m

As we know,

The shape factor will be:

⇒ [tex]SF=\frac{2 \pi l}{ln[\frac{1.08 b }{d} ]}[/tex]

By putting the value, we get

⇒       [tex]=\frac{2 \pi l}{ln[\frac{1.08\times 1}{0.2} ]}[/tex]

⇒       [tex]=3.7258 \ l[/tex]

hence,

The heat loss will be:

⇒ [tex]Q=SF\times K(T_2-T_1)[/tex]

       [tex]=3.7258\times 1\times 1.8\times (500-300)[/tex]

       [tex]=3.7258\times 1.8\times (200)[/tex]

       [tex]=1341.288 \ W/m[/tex]

Answer:

2,160,000

Explanation:

8/100 × 200000/1 = 8/1 × 2000/1

2000 × 8 = 16,000 = interest

200,000 + 16,000 = 216,000

216,000 × 10 = 2,160,000 = amount in bank account

Answer:

the energy is sgdrh35679

Keywords Are Reserved Words Which Are Not Use As Normal Cases But Used For Special Purpose In Our Program whereas, Data Type Tells The Compiler And Interpreter How The Program Is Going To Be Executed And Can Be Used At Every Cases.

Based on how they are stored in the computer, the types produced by these keywords can be categorized into two families, integer types and floating-point types.

Bit, byte, and word are terminology that can be used to refer to either memory or data storage units in computers.

The main distinction between text fields and keyword fields is that text fields are examined during indexing, whereas keyword fields are not.

This means that while keyword fields are indexed exactly as is, text fields are split down into their constituent phrases at indexing to allow for partial matching.

A word or collection of words that an Internet user enters into a search engine or search bar to conduct a search is referred to as a keyword in the context of digital marketing.

Therefore, All data types are keywords, but all keywords are not data types.

Learn more about data and keywords here:

https://brainly.com/question/9588905

#SPJ2

Answer:

The outer diameter of the spacers that yields the most economical and safe design is 25.03 mm

Explanation:

For steel bolt

Stress = 210 MPa or 210 N/mm2

Pressure = Stress* Area

Pbolt = 210 N/mm2 * 16^2 *(pi)/4

Pbolt = 210 N/mm2 * 200.96 mm^2 = 42201.6  N

For Brass spacer

Pressure = 42201.6  N

Area of Brass spacer = Pressure/Stress

Area of Brass spacer = 42201.6  N/145 N/mm^2 = 291.044 mm^2

Area of Brass spacer = (pi) (d^2 - 16^2)/4 =  291.044 mm^2

d^2 - 16^2 = 291.044 mm^2* 4/(pi) = 370.758

d^2 =  370.758 + 16^2

d^2 =   626.758

d = 25.03 mm

The outer diameter of the spacers that yields the most economical and safe design is 25.03 mm

Answer: Increase in the population of lower organisms.

Explanation: Raccoons are mesopredators found in the middle levels of food webs and have critical impacts on the dynamics of many other species. Thus, they greatly contribute to the functioning of the ecosystem.

They are naturally equipped to checkmate the population size of other organism that are below them (i.e., their preys) in the food web. They are; predators, pathogen carriers (such as rabies), and competitors, as they compete with some specialist in the food web.

Hence, the decrease in the population of raccoons will lead to the increase in the population size of lower organisms they prey on in the food web or chain.

Answer:

In a parallel circuit, the voltage across each of the components is the same, and the total current is the sum of the currents flowing through each component. ... In a series circuit, every device must function for the circuit to be complete. If one bulb burns out in a series circuit, the entire circuit is broken.

Explanation:

Answer:

the order higher is 3p79g5t88=yv5379

Answer:

Safety check is defined as rounding to make sure that the patients and the milieu (patients living quarters) is secured and free of harmful items that can be used to hurt someone.

Answer:

hdwhifniuewohfoyyhyeiudhwbwuxvgusvfgcvxg

Explanation:

Answer:

Electric current is the movement of electrons through a wire. Electric current is measured in amperes (amps) and refers to the number of charges that move through the wire per second. If we want current to flow directly from one point to another, we should use a wire that has as little resistance as possible.Current is directly proportional to voltage, inversely proportional to resistance. One of the most common electrical measurements you'll use is the watt, a unit of electrical power: W (Watts) = E (Volts) x I (Amperes). The quantity of electric charge is measured in coulombs.They can even pass through bones and teeth. This makes gamma rays very dangerous. They can destroy living cells, produce gene mutations, and cause cancer.

Explanation:

hey mate this is the best answer if you're studying engineering!

Answer:

The answer is below

Explanation:

Both a gage and a manometer are attached to a gas tank to measure its pressure. If the reading on the pressure gage is 65 kPa, determine the distance between the two fluid levels of the manometer if the fluid is a) mercury b) water

Solution:

A manometer is a device used to measure pressure. A manometer is made up of a U shaped tube containing liquid. The difference of pressure in the two arms causes the liquid to reach different heights.

a) The density of mercury ([tex]\rho_{Hg}[/tex]) = 13600 kg/m³, Pressure (P) = 65 kPa and g = 9.8 m/s², h = distance between the two fluid levels

[tex]P=\rho_{Hg}*g*h\\\\h=\frac{P}{\rho_{Hg}*g} =\frac{65*10^3\ Pa}{13600*9.81}=0.487\ m[/tex]

b) For water, [tex]\rho_w[/tex] = 1000 kg/m³, hence:

[tex]P=\rho_{w}*g*h\\\\h=\frac{P}{\rho_{w}*g} =\frac{65*10^3\ Pa}{1000*9.81}=6.6\ m[/tex]

Answer:

True

Explanation:

Tensile testing which is also referred to as tension testing is a process which materials are subjected to so as to know how well it can be stretched before it reaches breaking point. Hence, the statement in the question is true

so long so long so long so long so long

Explanation:

so long so long so long so long so long so long so long so long so long so long

Answer:

a) 156 meters

b) 58 m/s

c) 9.8 m/s^2

Explanation:

a) The horizontal displacement X = V *t

X = 50 * 3 = 150 meters

Vertical displacement = y = – g * t² / 2

Y = -9.8 *3*3/2 = -4.9*9 = 44.1

Net Displacement = Sqrt (X^2 +Y^2) = 156.34 = 156 meters

b) Speed of the projectile

vx = 50 m/s

vy = t*g = 9.8*3 = 29.4

V = Sqrt (vx^2 + vy^2) = 58 m/s

c) Acceleration is the acceleration due to gravity = 9.8 m/s^2

The magnitude of the displacement of the projectile is equal to 156 meters.

Given the following data:

Scientific data:

Mathematically, the magnitude of the displacement of a projectile is given by this formula:

[tex]Horizontal\;displacement = Vt\\\\Horizontal\;displacement = 50.0 \times 3.00[/tex]

Horizontal displacement = 150.0 meters.

[tex]Vertical displacement =\frac{1}{2} gt^2\\\\Vertical displacement =\frac{1}{2} \times 9.8 \times 3^2\\\\Vertical displacement =\frac{1}{2} \times 9.8 \times 9[/tex]

Vertical displacement = 44.1 meters.

[tex]D^2 = X^2 +Y^2\\\\D =\sqrt{44.1^2+150^2}[/tex]

D = 156.34 ≈ 156 meters.

b. For the speed of the projectile:

Vertical speed = tg

[tex]V_y = tg = 9.8\times3\\\\ V_y = 29.4\;m/s[/tex]

[tex]D^2 = V_x^2 +V_y^2\\\\D =\sqrt{50^2+29.4^2}[/tex]

D = 58 m/s.

c) The magnitude of the acceleration of the projectile is equal to the acceleration due to gravity ([tex]9.8 \;m/s^2[/tex]).

Read more on acceleration here: brainly.com/question/247283

$255 per hour

Total number of employed people = 16

(i) 5 people earn $15 per hour

That means that the total amount earned by those 5 is;

5 x $15 = $75 per hour

(ii) 4 people earn $17 per hour

That means that the total amount earned by those 4 is;

4 x $17 = $68 per hour

(iii) The remaining people earn $16 per hour.

There are 7 people remaining. i.e

16 - 5 - 4 = 7

That means that the total amount earned by those remaining (7) is;

7 x $16 = $112 per hour

The total hourly wage is therefore the sum of all the results in i, ii and iii. i.e

Total = $75 + $68 + $112

Total = $255

Therefore, the total hourly wage earned by all 16 people is $255

Answer:

C. Low viscosity for Maine in the winter and high viscosity for Florida in the summer.

Explanation:

The choice of motor oil or engine oil depends on the type of engine and also on the type of climate on which the engine runs.

In winter climates, we should use oil with low viscosity as at lower temperatures, the it flows more readily if its viscosity is low.

But the summer season needs a relatively thicker oil so as to reduce the thinning effect of the oil out of the engine.

Thus for Maine in the winter season, we need a low viscosity oil and for Florida a high viscosity oil in the summer season.

Therefore, option (c) is correct.

Answer:

Timing Diagrams 15 pts. A 10 MHz clock that generates a 0 to 5V pulse train with a 30% duty cycle is connected to input X of a two input OR gate that has a 20nS propagation delay. The clock also goes to an inverter with a 10 ns propagation delay. The output of the inverter goes to the Y input of the OR gate. a) Draw the circuit. 2 pts. b) Plot the output of the clock for two cycles. Show times and voltages. 5 pts. c) On the same page as part (b) plot the output of the inverter. Show times and voltages. 3 pts. d) On the same page as parts (b & c) plot the output of the OR gate. Show times and voltages. 5 pts.

Answer:

When employees follow procedures, they perform tasks correctly and provide consistent customer service. This enhances the quality of your organization's products and services. And, in turn, improves your company's reputation. Employees can know they are fulfilling their roles and take pride in their work.

Answer:

The main reason for the existence of an organization is to generate profits, but it is increasingly required through the legal and social obligation that companies are not only profitable entities, but promoters of the well-being and development of society.

Therefore, the balance between the resources for its financial goals and objectives and social responsibility goals will be achieved through the adoption of processes that include environmental and social management as an integral and important part of the general administration, which is not an exclusion for generation profitability, but a tool that will help achieve organizational goals and objectives.

Environmental and social management through certifications, programs and management systems, provides policies and procedures that help companies reduce their costs, eliminate waste, improve productivity, generate stakeholder satisfaction and several other benefits that promote continuous improvement and consequently the improvement in the company's positioning in the market.

Answer:

it’s IGS

Explanation:

because i read

Answer:

snap trap baits

Explanation: its kind of obvi, but i took the test and got it right.

Answer:

a) 158.4 HP.

b) 1235.6 °F.

Explanation:

Hello there!

In this case, according to the given information, it turns out possible for us to set up an energy balance for the turbine's inlets and outlets:

[tex]m_{in}h_{in}=W_{out}+m_{out}h_{out}[/tex]

Whereas the mass flow is just the same, which means we have:

[tex]W_{out}=m_{out}(h_{out}-h_{in})[/tex]

And the enthalpy and entropy of the inlet stream is obtained from steam tables:

[tex]h_{in}=1860.7BTU/lbm\\\\s_{in}= 2.2096BTU/lbm-R[/tex]

Now, since we assume the 80% accounts for the isentropic efficiency for this adiabatic gas turbine, we assume the entropy is constant so that:

[tex]s_{out}= 2.2096BTU/lbm-R[/tex]

Which means we can find the temperature at which this entropy is exhibited at 15 psia, which gives values of temperature of 1200 °F (s=2.1986 BTU/lbm-K) and 1400 °F (s=2.2604 BTU/lbm-K), and thus, we interpolate for s=2.2096 to obtain a temperature of 1235.6 °F.

Moreover, the enthalpy at the turbine's outlet can be also interpolated by knowing that at 1200 °F h=1639.8 BTU/lbm and at 1400 °F h=174.5 BTU/lbm, to obtain:

[tex]h_{out}=1659.15BUT/lbm[/tex]

Then, the isentropic work (negative due to convention) is:

[tex]W_{out}=2500lbm/h(1659.15BUT/lbm-1860.7BUT/lbm)\\\\W_{out}=-503,875BTU[/tex]

And the real produced work is:

[tex]W_{real}=0.8*-503875BTU\\\\W_{real}=-403100BTU[/tex]

Finally, in horsepower:

[tex]W_{real}=-403100BTU/hr*\frac{1HP}{2544.4336BTU/hr} \\\\W_{real}=158.4HP[/tex]

Regards!

Answer:

tie es que sumar restar y multiplicar

Explanation:

espero que sea así