For calculation of potential energy mass of the apple , average acceleration of the apple and height of apple is required.
Energy While for calculation of kinetic energy volume of the apple and time the apple was in air, the average velocity of the apple and amount of energy lost to friction is required.Based on the force exerted on the two objects, the potential energy equation is determined. P.E. = mgh, where m is the mass in kilograms, g is the acceleration caused by gravity (9.8 m/s2 at the earth's surface), and h is the height in meters, is the formula for gravitational force.The relationship between kinetic energy and an object's mass and squared velocity is given by K.E. = 1/2 m v2. If the mass is measured in kilograms and the speed is measured in meters per second, the kinetic energy is measured in kilogram-meters squared per second squared.For more information on kinetic and potential energy kindly visit to
https://brainly.com/question/11749818
#SPJ1
if the leftover energy in the previous problem is 134.9 j (it's not, don't go back and try to use this value) and the mass is 2 kg, what speed (in m/s) does the block have at the bottom of its slide? revisit the definition of ke if needed.
The speed of the block at the bottom of its slide is 16.4 m/s.
In the previous problem, the kinetic energy of the block was found to be 135 J.
The formula for kinetic energy is
KE = 1/2mv²,
Where:
m is the mass of the object and v is its velocity.Now we can use the same formula to find the velocity of the block at the bottom of its slide.
KE = 1/2mv²
We know that the mass of the block is 2 kg, and the kinetic energy at the end of the slide is 135 J.
KE = 135 Jm = 2 kg1/2mv² = 135 Jv² = 2(135 J) / 2 kgv² = 270 JV = sqrt(270 J) / 2 kgV = 16.4 m/s
Therefore, the speed of the block at the bottom of its slide is 16.4 m/s.
Learn more about kinetic energy: https://brainly.com/question/8101588
#SPJ11
The temperature of a gas stream is to be measured by a thermocouple whose junction can be approximated as a 1.2-mm-diameter sphere. The properties of the junction are k = 35 W/m °C, rho= 8500 kg/m3 ,and Cp = 320 J/kg °C, and the heat transfer coefficient between the junction and the gas is h = 65 W/m2 °C. Determine how long it will take for the thermocouple to read %95 of the initial temperature difference.
It will take about 12.12 minutes for the thermocouple to read 95% of the initial temperature difference of the sphere. This is due to difference in temperature.
What is the time required to read 95% of initial temperature difference?
In order to determine how long it will take for the thermocouple to read 95% of the initial temperature difference, the following formula is used:
t = (rho × V × Cp)/(h × pi × D) × ln ((Tinitial - T∞) / (Tinitial - Tcutoff))
where, t = time (s), ρ = density (kg/m³), V = volume (m³), Cp = specific heat capacity (J/kg °C), h = heat transfer coefficient (W/m²°C), D = diameter (m), Tinitial = initial temperature (°C), T∞ = surrounding temperature (°C), Tcutoff = temperature at which the thermocouple reading is 95% of the initial temperature difference (°C).
Substituting the given values into the above formula:
t = (8500 kg/m³ × (4/3 × pi × (0.0006 m)³)) / (65 W/m2 °C × pi × 0.0012 m) × ln ((100 °C - 25 °C) / (100 °C - 95 °C))
t = 727.31 s or 12.12 minutes.
Therefore, it will take approximately 12.12 minutes for the thermocouple to read 95% of the initial temperature difference.
Learn more about Thermocouple here:
https://brainly.com/question/14555057
#SPJ11
as a 4.4-kg object moves from (2 i 5 j) m to (6 i - 2 j) m, the constant resultant force acting on it is equal to (4 i - 3 j) n. if the speed of the object at the initial position is 4.9 m/s, what is the work done by the force, and what is its kinetic energy at its final position? as your answer in canvas, write the kinetic energy in joules.\
The kinetic energy of the object at its final position is 90.98 J.Given,Mass, m = 4.4 kg Initial position, r1 = (2 i + 5 j) m, Final position, r2 = (6 i − 2 j) m ,Initial velocity, u = 4.9 m/s ,Constant resultant force, F = (4 i − 3 j) N .To find the work done by the force,First, we need to find the displacement vector = r2 - r1= (6 i − 2 j) - (2 i + 5 j)= (6 - 2) i + (-2 - 5) j= 4 i - 7 j
Magnitude of the displacement vector,= √(4² + (-7)²)= √65 m Now, we can find the work done by the force,W = F.s= (4 i - 3 j) . (4 i - 7 j)= 4(4) + 3(7)= 37 J
Therefore, the work done by the force is 37 J.
To find the kinetic energy of the object at its final position,First, we need to find the final velocity of the object by using the work-energy principle.Initial kinetic energy, K1 = (1/2)mu²= (1/2) × 4.4 × (4.9)²= 53.98 J
Work done by the force, W = 37 JFinal kinetic energy, K2 = K1 + W= 53.98 + 37= 90.98 JTherefore, the kinetic energy of the object at its final position is 90.98 J.
For such more questions on displacement
https://brainly.com/question/28952425
#SPJ11
The electric potential at a distance d
from a certain point charge is V relative to infinity. What is the potential (relative to infinity) at half the distance for the same charge?
A. V/4
B. 2 V
C. V/2
D. 4 V
The electric potential from a certain point charge when the distance is halve for the same charge will be V/2. Thus, the correct option will be C.
According to the Coulomb's law, the electric field is the gradient of the electric potential. And, the electric potential V is given by:V = kQ/r, where Q is the charge, r is the distance between the charge and the point where the potential is being calculated, and k is Coulomb's constant. Here, the electric potential at a distance d from a certain point charge is V relative to infinity.
The electric potential (relative to infinity) at half the distance for the same charge is the distance r/2, so:
V' = kQ/r
2V' = kQ/(d/2)
V' = 2kQ/d
V' = V/2
Therefore, the electric potential at half the distance for the same charge is V/2.
Learn more about Electric potential here:
https://brainly.com/question/12645463
#SPJ11
an electromagnetic wave is transporting energy in the positive y direction. at one point and one instant the magnetic field is in the positive x direction. the electric field at that point and instant points in the
Energy is being transported in the positive y direction by an electromagnetic wave. The magnetic field is in the positive x direction at one spot and one moment. At that precise moment, the electric field is oriented in the "negative z" direction.
The given electromagnetic wave is transporting energy in the positive y direction. At one point and one instant, the magnetic field is in the positive x direction. Now we have to find the direction of the electric field at that point and instant. According to the right-hand rule, when the magnetic field is directed towards the positive x-axis, the electric field will be directed downwards along the negative z-axis. Therefore, the electric field at that point and instant points in the negative z direction.
To know more about electromagnetic wave:https://brainly.com/question/75996
#SPJ11
Two charges, -2.1 μC and -5.6 μC , are located at (-0.50 m , 0) and (0.50 m , 0), respectively. There is a point on the x-axis between the two charges where the electric field is zero. Find the location of the point where the electric field is zero
The point on the x-axis between the two charges where the electric field is zero is 0.747 m, when the charges -2.1 μC and -5.6 μC are located at (-0.50 m , 0) and (0.50 m , 0), respectively.
An electric field is defined as the electric force per unit charge. It is a field of force surrounding electrically charged particles, such as electrons or protons in motion, that exerts force on surrounding matter. It is represented by the symbol E.
The electric field E at any point (x,y) on the x-axis due to the charge Q1 at (-0.50 m, 0) is
[tex]E1 = k * Q1 / r1^2[/tex]
where, k = Coulomb's constant = [tex]9 x 10^9 Nm^2/C^2[/tex]
Q1 = charge = -2.1 μC
r1 = distance between Q1 and
(x,y) = (0.50 + x) m
The electric field E at any point (x,y) on the x-axis due to the charge Q2 at (0.50 m, 0) is
[tex]E2 = k * Q2 / r2^2[/tex]
where,
Q2 = charge = -5.6 μC
r2 = distance between Q2 and (x,y) = (0.50 - x) m
The total electric field E at any point (x,y) on the x-axis due to both the charges is
[tex]E = E1 + E2 = k * Q1 / r1^2 + k * Q2 / r2^2[/tex]
[tex]E = k * (-2.1 * 10^-6) / (0.5 + x)^2 + k * (-5.6 * 10^-6) / (0.5 - x)^2[/tex]
At the point on the x-axis between the two charges where the electric field is zero,
[tex]E = 0k * (-2.1 * 10^-6) / (0.5 + x)^2 + k * (-5.6 * 10^-6) / (0.5 - x)^2 = 0[/tex]
Simplifying, we get [tex](0.5 + x)^2 / (0.5 - x)^2 = 2.667x^2 + 2.667x - 0.50 = 0[/tex]
Solving for x, we get
x = -1.74 m or
x = 0.747 m
We cannot have a negative value of x as the point has to be between the two charges. So, the location of the point where the electric field is zero is x = 0.747 m.
Learn more about electric field: https://brainly.com/question/14372859
#SPJ11
given what you learned from the figure, rank these types of light in order of increasing energy. 1. radio 2. infrared 3. orange 4. green 5. ultraviolet
Answer:
✓ 1. radio 2. infrared 3. orange 4. green 5. ultraviolet
Explanation:
for a given mass of gas at constant temperature, the volume of the gas varies inversely with pressure.a. 3Pb. P/3c. 3P/Td. 9P
The volume of the gas varies inversely with pressure, and the correct answer is (b) P/3.
According to Boyle's Law, at a constant temperature, the volume of a gas is inversely proportional to its pressure. Mathematically, this can be expressed as:
PV = k
where P is the pressure of the gas, V is its volume, and k is a constant.
If we assume that the mass of the gas remains constant, then k is also constant. So we can write:
[tex]P_1V_1 = k and P_2V_2 = k[/tex]
where[tex]P_1 and V_1[/tex] are the initial pressure and volume, and [tex]P_2 and V_2[/tex] are the final pressure and volume.
If we divide these two equations, we get:
[tex]P_1V_1/P_2V_2 = 1[/tex]
Since[tex]V_1[/tex] is inversely proportional to [tex]P_1[/tex], we can write:
[tex]V_1 = k/P_1[/tex]
Similarly, [tex]V_2 = k/P_2.[/tex]
Substituting these values in the above equation, we get:
[tex](k/P_1)/(k/P_2) = 1[/tex]
Simplifying this, we get:
[tex]P_2/P_1 = V_1/V_2[/tex]
Since we are given that the temperature remains constant, we can assume that k is constant, and therefore:
[tex]V_1/P_1 = V_2/P_2[/tex]
If we let [tex]P_2 = 3P_1[/tex], then we get:
[tex]V_1/P_1 = V_2/(3P_1)[/tex]
Simplifying this, we get:
[tex]V_1/V_2 = 1/3[/tex]
for such more question on volume
https://brainly.com/question/14197390
#SPJ11
Let the mass of the sled be m and the magnitude of the net force acting on the sled be Fnet . The sled starts from rest. Consider an interval of time during which the sled covers a distance s and the speed of the sled increases from v1 to v2 . We will use this information to find the relationship between the work done by the net force (otherwise known as the net work) and the change in the kinetic energy of the sled. Use W = F s cos (theta) to find the net work Wnet done on the sled. Express your answer in terms of some or all of the variables m ,v1 and v2 .
Total work done is Wnet = 1/2mv₂² - 1/2mv₁²
Let the mass of the sled be m and the magnitude of the net force acting on the sled be Fnet .
The sled starts from rest. Consider an interval of time during which the sled covers a distance s and the speed of the sled increases from v₁ to v₂ . We will use this information to find the relationship between the work done by the net force (otherwise known as the net work) and the change in the kinetic energy of the sled.
Use W = F s cos (theta) to find the net work Wnet done on the sled. Express your answer in terms of some or all of the variables m ,v₁ and v₂.Using the work-energy principle, we can calculate the work done on an object in terms of its change in kinetic energy. Consider the sled being acted upon by a force Fnet.
W = ΔK is used to calculate the work done on the sled as it moves from rest to velocity v₁ and then to velocity v₂ over a distance s.
Considering the sled to be the system under study, we can write the net work done on the sled as Wnet = ΔK.Wnet = 1/2mv₂² - 1/2mv₁² = Fnet s cos θWnet = Fnet s cos θ = 1/2mv₂² - 1/2mv₁²
To know more about net force click on below link:
https://brainly.com/question/29261584#
#SPJ11
what is the acceleration of an object flying upward during free fall?
During free fall, an object is subject to the force of gravity and its acceleration is equal to the acceleration due to gravity (g), which is approximately 9.81 meters per second squared (m/s²) near the surface of the Earth.
If an object is flying upward during free fall, its acceleration will still be equal to -9.81 m/s² (note the negative sign indicating that the acceleration is downward). This is because the direction of the acceleration due to gravity is always toward the center of the Earth.
Even if an object is moving upward, it is still subject to the gravitational force, which causes it to decelerate until it reaches its highest point and then starts to fall back down.
To learn more about acceleration refer to:
brainly.com/question/30762941
#SPJ4
which of the following actions will cause the relative humidity of an air parcel to increase? select all that apply
a. Keep the parcel’s temperature constant and increase the parcel’s dew point
b. Decrease the parcels temperature and increasethe parcels dew point
c. Keep the parcel’s temperature constant and keep the parcels dew point constant
d. Increase the parcels temperature and increase the parcels dew point
e. Keep the parcels dew point constant and increase the parcels temperature
The relative humidity of an air parcel will increase if any of the following actions are taken:
Keep the parcel’s temperature constant and increase the parcel’s dew pointDecrease the temperature of the parcel and increase the parcels dew pointIncrease the temperature of the parcel and increase the parcels dew pointKeep the parcels dew point constant and increase the temperature of the parcelWhat is relative humidity?To understand this further, we can look at the formula for relative humidity, which is the amount of water vapor in the air divided by the amount of water vapor that can exist at a particular temperature. When the temperature is kept constant and the dew point increases, the amount of water vapor in the air increases, resulting in an increase in relative humidity.
The followings are the given options and the actions they will take that will cause the relative humidity of an air parcel to increase:
Option A: Keep the parcel's temperature constant and increase the parcel's dew point. This action would increase the RH of the air parcel because it will increase the quantity of water vapor in the air parcel. As the parcel's temperature is constant, the ability of the air to hold water vapor also remains constant.
Option B: Decrease the parcel's temperature and increase the parcel's dew point. This action would also increase the RH of the air parcel. As the temperature of the parcel decreases, the amount of moisture that the air can contain also decreases. When the dew point is raised, the quantity of water vapor in the air parcel rises relative to the amount it can carry.
Option C: Keep the parcel's temperature constant and keep the parcel's dew point constant. In this case, there will be no increase in RH because the quantity of water vapor in the air parcel will remain the same as the ability of the air to hold water vapor remains constant.
Option D: Increase the parcel's temperature and increase the parcel's dew point. Increasing the parcel's temperature will raise the ability of the air to hold water vapor, but it will not increase the amount of water vapor in the air parcel. As a result, the RH of the air parcel will decrease.
Option E: Keep the parcel's dew point constant and increase the parcel's temperature. This action will also decrease the RH of the air parcel as it will increase the amount of moisture that the air can hold. Thus, the relative humidity will decrease.
To know more about relative humidity follow
https://brainly.com/question/13275394
#SPJ11
2.1 [2] As more resistors are added in series, the equivalent resistance of the circuit approaches infinity. In contrast, as more resistors are added in parallel, the equivalent resistance a. approaches infinity b. approaches zero c. becomes zero d. approaches 1 Ω
2.2 [2] Kirchhoff's loop rule is equivalent to which of the following principles? a. conservation of charge b. conservation of energy c. conservation of mass d. conservation of force
2.1 As more resistors are added in parallel, the equivalent resistance approaches zero
2.2 Kirchhoff's loop rule is equivalent to the conservation of energy principle.
As more resistors are added in series, the equivalent resistance of the circuit approaches infinity. In contrast, as more resistors are added in parallel, the equivalent resistance approaches zero. This statement is TRUE. The equivalent resistance, Req, of a parallel combination of resistors is less than any of the resistors in the combination, while for a series combination it is equal to the sum of the resistances.
Kirchhoff's loop rule is equivalent to the conservation of energy principle. Kirchhoff's loop rule or Kirchhoff's voltage law (KVL) is a result of the conservation of energy principle. The principle of conservation of energy states that energy can neither be created nor destroyed, it can only be transformed from one form to another. In a closed loop, the total energy gained is equal to the total energy lost, according to the principle of conservation of energy.
Learn more about Kirchhoff's loop rule and equivalent resistance at : https://brainly.com/question/30580929
#SPJ11
A dragster is travelling east when the parachute opens and slows the dragster for 4.5 seconds at a rate of 10 m/s2 west. What was the dragster's change in velocity due to the parachute?
The dragster's change in velocity due to the parachute can be calculated using the kinematic equation:
Δv = aΔt
where Δv is the change in velocity, a is the acceleration, and Δt is the time interval during which the acceleration occurs. In this case, the dragster is initially travelling east, so its velocity is positive, and the parachute applies a force in the opposite direction, resulting in a negative acceleration.
Given that the acceleration is -10 m/s² (westward) and the time interval is 4.5 seconds, we can calculate the change in velocity as:
Δv = (-10 m/s²) x (4.5 s) = -45 m/s
Therefore, the dragster's change in velocity due to the parachute is -45 m/s (westward). This means that the dragster's velocity is reduced by 45 m/s in the westward direction over the 4.5-second interval during which the parachute is deployed.
To know more about velocity , visit :
https://brainly.com/question/17127206
#SPJ1
The change in velocity due to the parachute is -45 m/s east
What is velocity ?
Velocity is a vector quantity that describes the speed and direction of motion of an object. In other words, velocity is the rate at which an object changes its position in a specific direction.
Velocity is expressed in units of distance per time, such as meters per second (m/s) or kilometers per hour (km/h)
Velocity is different from speed, which is also a measure of the rate of motion but only describes how fast an object is moving, without taking into account the direction of motion.
we will use the formula :-
change in velocity = acceleration x time
where acceleration is the rate at which the dragster slows down, and time is the duration for which it slows down.
Here, the dragster is travelling east, and the parachute applies a force in the opposite direction (west), causing it to slow down. So, the acceleration is -10 m/s^2 (negative because it's in the opposite direction to the velocity).
The time for which the dragster slows down is 4.5 seconds.
Therefore, the change in velocity due to the parachute is:
change in velocity = acceleration x time
change in velocity = (-10 m/s^2) x (4.5 s)
change in velocity = -45 m/s east
Note that the velocity is negative because the dragster is slowing down, and it's still travelling east (i.e., in the positive direction).
To know more about velocity visit :-
https://brainly.com/question/80295
#SPJ1
hydroelectric dams generate electricity by question 20 options: a. using the energy of the river to produce steam. b. using run-of-the-river systems, in which turbines are placed into the natural water flow. c. water impoundment, in which dam operators control the rate of water flow to turbines. d. using generators that are placed on the bottom of a river. e. converting the kinetic energy of the water impounded behind a dam into potential energy.
Hydroelectric dams generate electricity through water impoundment, in which dam operators control the rate of water flow to turbines.
c is the correct option.
Hydroelectric dams are dams used to produce electricity. The movement of water drives turbines, which power generators that generate electricity.
The movement of water, generated by gravity, is what drives turbines. Hydroelectric dams are the most widely used renewable energy source, accounting for approximately 16% of global electricity production.
Hydroelectric dams generate electricity through water impoundment, in which dam operators control the rate of water flow to turbines.
This is the process of using turbines that are powered by the movement of water that has been dammed to generate electricity.
Turbines are powered by water that has been dammed to generate electricity, which is then sent to a power station to be used.
The electricity generated from hydroelectric dams is clean and safe, making it an important part of the renewable energy mix. They are also an essential part of the global infrastructure because they provide reliable, low-cost power.
They also assist in the management of rivers, flood control, and irrigation systems in various parts of the world.
To know more about Hydroelectric dams: https://brainly.com/question/18776929
#SPJ11
ercury's perihelion slowly precesses around the sun by a bit less than 2 degrees per century. this precession can be fully accounted for by newton's theory of gravity, although general relativity also gives the same answer. group of answer choices true false
The statement is true. Mercury's precession can be fully accounted for by both Newton's theory of gravity and general relativity.
Newton's law of universal gravitation states that any two bodies in the universe are attracted to each other with a force that is directly proportional to the product of their masses and inversely proportional to the square of the distance between them. This force can explain why the perihelion of Mercury is slowly precessing around the sun. According to Einstein's general theory of relativity, gravity is caused by the curvature of space-time around a massive body, such as the sun. This curvature of space-time causes Mercury to precess around the sun.
Newton's theory of gravity and general relativity provide equivalent explanations for the precession of Mercury's perihelion, which is a phenomenon in celestial mechanics. The precession of Mercury's perihelion is the slow rotation of the planet's elliptical orbit around the Sun's perihelion (the point of closest approach).It is well-known that Mercury's perihelion rotates by 42.98 arcseconds per century, or 1.39 degrees per century. This is caused by the gravitational influence of other planets, such as Venus and Jupiter, which produce small changes in Mercury's orbit. However, when this is taken into account, a tiny residual effect remains that cannot be accounted for using Newton's theory of gravity. This additional precession, known as the anomalous precession, can only be explained by general relativity.
The statement "Mercury's perihelion slowly precesses around the sun by a bit less than 2 degrees per century. This precession can be fully accounted for by Newton's theory of gravity, although general relativity also gives the same answer." is true.
To know more about Newton's theory of gravity please visit :
https://brainly.com/question/11490572
#SPJ11
A bus engine transfers chemical potential energy into ___ so that the bus moves.
a. kinetic energy
b. thermal energy
c. gravitational potential energy
d. electrical energy
the concentration of which component of the atmosphere varies the most?
The concentration of water vapor varies the most in the atmosphere.
The atmosphere is a thin layer of gas that surrounds the Earth. The atmosphere is composed of roughly 78% nitrogen and 21% oxygen, with trace amounts of other gases like argon and carbon dioxide. In addition, water vapor and aerosols are also present in the atmosphere.
Water vapor is the atmospheric component that fluctuates the most in concentration. It has a critical role in the planet's climate and is present in varying amounts in all parts of the atmosphere. Water vapor concentration is essential in the Earth's energy balance since it is a greenhouse gas that captures radiation from the sun and heats the planet's surface.
The amount of water vapor in the atmosphere can vary greatly depending on the temperature, location, and other environmental factors. Warm air can hold more water vapor than cold air, and areas with higher humidity can have more water vapor than arid regions. Overall, the concentration of water vapor in the atmosphere is constantly changing and fluctuating.
To learn more about water vapor, visit: https://brainly.com/question/1361830
#SPJ11
An electroscope is a device with a metal knob, a metal stem, and freely hanging metal leaves used to detect charges. The diagram below shows a positively charged leaf electroscope.
As a positively charged glass rod is brought near the knob of the electroscope, the separation of the leaves will
remain the same
increase
As a positively charged glass rod is brought near the knob of the electroscope, the separation of the leaves will increase.
What is Charge?
Charge is a fundamental property of matter that determines how objects interact with each other through the electromagnetic force. It is a physical property that can be positive or negative and can be measured in coulombs (C).
This is because the positively charged glass rod will induce a negative charge on the metal knob of the electroscope. The negative charges will repel the electrons in the metal leaves, causing them to move away from each other and increasing their separation. The greater the amount of charge on the glass rod, the greater the separation between the leaves will be.
Learn more about Charge from given link
https://brainly.com/question/18102056
#SPJ1
A ball rolls across the floor, slowing down with constant acceleration of magnitude . The ball has positive velocity ???? after rolling a distance x across the floor.
Calculate the ball's initial speed ????0 if ????= 4.51 m/s2, ????=11.17 m/s, and x=2.66 m.
A ball rolls across the floor, slowing down with a constant acceleration of magnitude a = 4.51 m/s2.
The ball has positive velocity v after rolling a distance x = 2.66 m across the floor.
To calculate the ball's initial speed v0 if
v = 11.17 m/s.
The initial velocity of the ball, v0 =?
The final velocity of the ball, v = 11.17 m/s
The acceleration of magnitude a = 4.51 m/s2
Distance travelled, x = 2.66 m
If an object has initial velocity v0, constant acceleration a, and travelled distance x, then its final velocity is given by:
v2 = v0² + 2ax
Here, the ball's initial velocity is v0, and its final velocity is v.
After substituting the given values, we have:
v2 = v0² + 2ax
=> (11.17)²
= v0² + 2(4.51)(2.66)
=> 124.57
= v0² + 25.39
=> v0² = 124.57 - 25.39
=> v0² = 99.18 => v0 = √99.18
=> v0 = 9.96 m/s
Hence, the initial velocity of the ball is v0 = 9.96 m/s.
To know more about velocity:
https://brainly.com/question/29519833
#SPJ11
greenhouse gases in the atmosphere selectively absorb radiation at what wavelength?
Answer:
They absorb radiation in the ultraviolet area - somewhat less than 4000 Angstroms or 400 mμ.
The reduction of the ozone layer in the upper atmosphere causes more of the shorter wavelengths to reach the surface of the earth and then to be reradiated at longer wavelengths causing global warming.
If I heated up a glass of 100 grams of water, and the temperature changed from 25℃ to 31℃, how much heat was needed to do that (in calories)?
Answer:
6° because some heat is released out of surrounding. if 100 over six which is equal to sixtenn point four
what device is used through ureteroscope to capture an inact calculus or fragments if fractured by laser
The device used through a ureteroscope to capture an intact calculus or fragments if fractured by laser is called a basket retrieval device.
A ureteroscope is a specialized tool that is used to examine and treat the inside of the ureter and kidney. It is made up of a long, thin tube with a camera and a light source at the end, which is inserted into the patient's urinary tract through the urethra. The physician will be able to examine the lining of the bladder, ureters, and kidneys during this examination.
A basket retrieval device is a specialized tool that is used during ureteroscopy, which is a minimally invasive surgical technique used to examine the inside of the urinary tract. It is used to remove kidney stones or any fragments that have been broken down by laser lithotripsy.The basket retrieval device works by capturing the stones or fragments with its metal "basket" and then removing them from the body. The physician will then be able to extract the stones or fragments by retracting the basket into the ureteroscope's working channel. The stones will be disposed of or sent to a lab for further testing.
More on ureteroscope: https://brainly.com/question/28170411
#SPJ11
1 80 kg scaffold is 5.80 m long. it is hanging with two wires, one from each end. a 580 kg box sits 1 m from the left end. what is the tension in the right hand side wire?
The tension in the right-hand side wire is 6525 N.
Given:
Weight of the scaffold = 180 kgLength of the scaffold = 5.8 mWeight of the box = 580 kgDistance of the box from left end = 1 mLet the tension in the left wire = T1Let the tension in the right wire = T2To find: Tension in the right-hand side wireWe know that the sum of forces acting in a vertical direction should be equal to 0 as there is no acceleration in the vertical direction. ∑Fv = 0In the horizontal direction, there are no forces acting on the system.
∑Fh = 0Now considering forces in the vertical direction: T1 + T2 = (Weight of scaffold + Weight of the box) gT1 + T2 = (180 + 580) x 9.8T1 + T2 = 7644 N1. From the diagram, we can see that the box is nearer to the left side. Hence, the tension force in the left wire is greater than the tension force in the right wire.
T1 > T22. Let's take moments about the right end of the scaffold as shown in the figure below.
∑Mr = 0T1 × 5.8 = T2 × 1T2 = 5.8/1 × T1T2 = 5.8T1Now, we can substitute the value of T2 in equation (1):
T1 + T2 = 7644N6.8 T1 = 7644 N T1 = 1125 NTo find T2, we can substitute the value of T1 in equation (2):
T2 = 5.8 × T1T2 = 5.8 × 1125 N T2 = 6525 NTherefore, the tension in the right-hand side wire is 6525 N.
Learn more tension: https://brainly.com/question/4001686
#SPJ11
What are water droplets that act as a prism?
O a
Ob
OC
Od
mirage
rainbow
filter
concave mirror
Water droplets that act as prism are phenomenon known as : b) rainbow.
What are water droplets that act as prism?When light enters water droplet and is refracted, it is dispersed into its component colors due to difference in the index of refraction of each color of light. This results in band of colors in the shape of arc with red on outer edge and violet on inner edge, with other colors of spectrum in between. This is the same effect as prism which disperses light in the same way.
Rainbows appear in seven colors because water droplets break sunlight into seven colors of spectrum and you get the same result when sunlight passes through prism. Water droplets in the atmosphere act as prism though traces of light are very complex.
To know more about rainbow, refer
https://brainly.com/question/1550509
#SPJ1
basic behavior: according to your data, does this resistance increase or decrease with voltage? a reasonable (and correct) thought is that the impact is really with temperature, as the light bulb heats up with more power going into it. how does your data imply resistance varies with temperature?
Based on the given question, the resistance will: increase with the increase in voltage.
The reason behind this is that resistance and voltage have a direct relationship. As the voltage increases, the resistance also increases. This can be explained by Ohm’s Law which states that V= IR where V is voltage, I is current and R is resistance. As per the second part of the question, it is implied that the resistance varies with temperature.
The resistance of any material depends upon temperature, and a rise in temperature increases the resistance of the material. The light bulb acts as a resistor, and its resistance will increase as the temperature increases due to an increase in the temperature of the filament of the bulb.
The resistance is directly proportional to the temperature of the bulb, and it is represented by the equation
R = R₀ (1 + αt),
where R is resistance, R₀ is the resistance at a particular temperature, α is the temperature coefficient of resistance, and t is the temperature difference in Celsius.
Therefore, based on the data provided, it can be concluded that resistance increases with the increase in temperature which results in the heating of the light bulb, which is a resistor.
To know more about resistance refer here:
https://brainly.com/question/29427458#
#SPJ11
When the rock hlt Cesar, the impact was softened by several protective features of the head. Which of the following structures would have helped to protect the brain from the external force? View Available Hint() Bone Oligodendrocytes Cerebrospinal fluid Basal ganglia Hair Dura mater White matter
The structure that would have helped to protect the brain from the external force when the rock hit Cesar are as follows: Dura mater and Cerebrospinal fluid.
What is the central nervous system? The central nervous system (CNS) is responsible for processing incoming stimuli from the peripheral nervous system and producing a coordinated response. It includes the brain and the spinal cord.
The brain is the largest component of the CNS, comprising 2% of the body's weight but consuming about 20% of its oxygen and nutrients. It consists of three main parts: the brainstem, the cerebellum, and the cerebrum.
The brainstem is responsible for regulating critical functions like respiration, circulation, and digestion; the cerebellum controls motor coordination, and the cerebrum is the area of the brain responsible for sensory perception, emotion, and movement.
What is external force? External forces, also known as contact forces, are forces that act on an object as a result of its interaction with its surroundings. Forces that do not require contact to take effect, such as gravitational and magnetic forces, are not considered external forces.
Examples of external forces are gravity, air resistance, tension, and friction. Dura mater and Cerebrospinal fluid as the structure that would have helped to protect the brain from the external force when the rock hit Cesar. When a rock hits Cesar, the external force created by it must be transferred to the skull, and ultimately the brain.
However, several protective features of the head help to reduce the severity of the impact. The brain is protected by two main structures: the dura mater and the cerebrospinal fluid.
The dura mater is the outermost layer of the meninges, which is a protective membrane covering the brain and spinal cord. It acts as a cushion, absorbing some of the external force generated by the impact.
Cerebrospinal fluid is a clear liquid that flows throughout the central nervous system, filling the space between the brain and the skull. It acts as a shock absorber, reducing the impact's intensity by distributing the force more evenly.
To know more about central nervous system, refer here:
https://brainly.com/question/29974261#
SPJ11#
g as a prank, someone drops a water-filled balloon out of a window. the balloon is released from rest at a height of 10.0 m above the ears of a man who is the target. then, because of a guilty conscience, the prankster shouts a warning after the balloon is released. the warning will do no good, however, if shouted after the balloon reaches a certain point, even if the man could react infinitely quickly. assuming that the air temperature is 20 c and ignoring the effect of air resistance on the balloon, determine how far above the man's ears this point is.
The point at which the warning will do no good is 7.50 m above the man's ears.
When a water-filled balloon is released from rest at a height of 10.0 m above the ears of a man, the warning will do no good if shouted after the balloon reaches a certain point. Assuming that the air temperature is 20°C and ignoring the effect of air resistance, this point is 7.50 m above the man's ears.
The vertical displacement (d) can be determined using the equation [tex]d = \frac{vf2}{2g}[/tex], where vf is the final velocity and g is the acceleration due to gravity (9.81 m/s2).
Since the balloon was released from rest, the initial velocity is 0 m/s. Therefore, [tex]d = \frac{02 }{ 2} (\frac{9.81 m}{s2} ) = 0[/tex]m. Since the initial height was 10.0 m, the final height is 10.0 m + 0 m = 10.0 m.
The point at which the warning will do no good is 7.50 m above the man's ears, so the final height of the balloon must be 10.0 m - 7.50 m = 2.50 m.
Therefore, the point at which the warning will do no good is 7.50 m above the man's ears.
Learn more about vertical displacement: brainly.com/question/2289543
#SPJ11
what are two characteristics of net forces that are balanced
Balanced net forces have equal and opposing forces that cancel each other out and provide a net force of zero, which does not alter the motion of an item.
An object's velocity remains constant and motion is unaltered when the net forces acting on it are balanced. This indicates that the thing is either stationary or moving continuously. When the forces exerted on an item are opposing in direction and of equal magnitude, they are said to be balanced forces. The forces in this situation cancel one another out, leaving a net force of zero. This can happen when one force is applied to an item and that object applies an equal and opposite force in the opposite direction to another object. It can also happen when two or more forces are applied in opposing directions and of equal magnitude. Understanding equilibrium and stability in physics requires a knowledge of the idea of balanced forces.
learn more about Balanced net forces here:
https://brainly.com/question/29769471
#SPJ4
suppose that one particle of the flow approaches a plate of a capacitor. explain what happens to the other plate of the capacitor?
The other plate of the capacitor is induced with an opposite charge through electrostatic induction as the particle of the flow approaches one plate.
As the particle of the flow approaches one plate of the capacitor, it induces an opposite charge on the other plate of the capacitor through the process of electrostatic induction. The electric field produced by the charge on the approaching plate pushes the electrons on the other plate away from the approaching plate, resulting in an accumulation of charge of the opposite sign on the other plate.
This process continues until the potential difference between the plates becomes large enough to produce a discharge, after which the process of electrostatic induction ceases. The discharge may occur in the form of a spark or a breakdown of the dielectric material separating the plates, depending on the strength of the electric field and the dielectric strength of the material.
Overall, the other plate of the capacitor experiences a temporary polarization and a buildup of charge of the opposite sign due to the approaching particle.
To know more about capacitor, refer here:
https://brainly.com/question/30889004#
#SPJ11
Describes depolarizing vs nondepolarizing neuromuscular blockers
Acetylcholine and non-depolarizing blockers battle it out for receptors in order to function. They assist with surgery and mechanical ventilation. Depolarizing substances.
On the other hand, result in prolonged activation and consequent desensitisation of the receptors.
Non-depolarizing neuromuscular blockers (nNMBs) are given as adjuvant therapy in the management of critically sick patients as well as as primary therapy to facilitate endotracheal intubations. nNMBs (rocuronium, vecuronium, pancuronium, atracurium, cisatracurium, mivacurium) are primarily used during routine and emergency intubations to facilitate airway management and lower the risk of laryngeal injury. This activity describes the indications, mode of action, administration techniques, significant adverse effects, contraindications, monitoring, and toxicity of nNMBs so that healthcare professionals can guide patient therapy towards the best results possible during anaesthesia and other medical procedures where nNMBs are beneficial therapeutically.
Learn more about Depolarizing here:
https://brainly.com/question/25533751
#SPJ4
