d. Write the symbol for the nucleus that completes each nuclear equation. (1 point each)
Answer:
Ra, 88
Ru, 44
Cr, 24
Explanation:
i
the remaining mass number is 224(228 - 4), and it's atomic number is 88(90 - 2). The element is Radium, Ra
ii
the remaining mass number is 98(98 - 0), and it's atomic number is 44(45 - 1). The element is Ruthenium, Ru
iii
The remaining mass number is 52(52 - 0), and it's atomic number is 24(23 - -1). The element is Chromium, Cr
why do i need physics for zoology
Answer:
No, buddy physics is not important for zoology you should take biology ok...Hope you like it please thank me and follow me
What is the difference between cytology and histology
Explanation:
what is the difference between cytology and histology
Histology involves the study of tissue and Cytology involves the study of cells, both of which are derived from various organs of the human body. The Histology laboratory is responsible for the preparation of tissue for diagnosis by Pathologists.
Select the correct answer. Ben has $10 to spend on dinner. He can have a pizza delivered, drive to a burger place, or go to the grocery store to get ingredients for a fresh salad. In the end, he goes with the salad. If each meal would have cost him the same amount, what is Ben’s incentive for choosing salad? A. to eat a healthier meal B. to help the local economy C. to save gas D. to save on his telephone bill
Answer:
A. to eat a healthier meal
Explanation:
The answer would be A, to eat a healthier meal. Eating a serving of mixed greens can enable Ben to shed pounds in the event that it encourages you to diminish your aggregate calorie admission. Pick filling fixings with the goal that you are not as ravenous and eat less, and keep your plates of mixed greens low in calories so they give fewer calories than the feast or tidbit that they are supplanting.
Systemic circulation requires help from which of the following bones, lungs, arteries and veins, or muscles
Answer:
Artery and viens
Explanation:
A uniform horizontal beam with a length of 8m and weigh of 200N is attached to a wall by a pin connection ..Its far end is supported by the cable tha makes an angle of 53.0 with the beam. If 600N person stands 2m from the wall , find the tension in the cable as well as the magnitude and direction of the force exerted by the wall on the beam.
Answer:
The tension in the cable is approximately 1440.0 N
Explanation:
The length of the beam = 8 m
The weight of the beam = 200 N
The angle made by the beam support cable = 53°
The weight of the person = 600 N
The position where the person stands = 2 m
The forces acting are the weight of the cable acting at the center of the beam and the weight of the person acting at 2 m from the wall
Therefore, we have;
Sum of moments = 0, which gives;
2000 × 4 + 2 × 600 - 8 × [tex]T_y[/tex] = 0
2000 × 4 + 2 × 600 = 8 × [tex]T_y[/tex]
[tex]T_y[/tex] = 9200/8 = 1150 N
The tension in the cable, T = The component of the force in the cable
The vertical component of the tension [tex]T_y[/tex] = T×sin(53)
Therefore;
T = [tex]T_y[/tex]/(sin(53)) = 1150/(sin(53 degrees)) = 1439.96 ≈ 1440 N
The tension in the cable, T is approximately 1440 N.
Which statement describes a property of a proton?
Answer:
They have no charge and are present in the nucleus of an atom. They have a negative charge and travel around the nucleus of an atom. They have a positive charge and travel around the nucleus of an atom
Explanation:
The electrons, which are negatively charged particles, are drawn to the protons because they have a positive electric charge. This keeps them in an orbit around the nucleus. A proton, therefore, possesses the quality of a positive charge.
What is proton?The proton is a stable subatomic particle with a rest mass of 1.67262 1027 kg, or 1,836 times the mass of an electron, with a positive charge that is equal to one electron's charge in magnitude.
All atomic nuclei, except for the hydrogen nucleus, are composed of protons and neutrons, which are electrically neutral particles (which consist of a single proton). A given chemical element's nuclei all contain the same number of protons.
They exist in the atom's nucleus and are not charged. They move around the atomic nucleus and have a negative charge. Likewise, they move about an atom's nucleus and have a positive charge.
Typically, a proton is made up of three quarks, which are tiny subatomic particles.
The protons are the electrically charged atom-nucleus particles that help hold the nucleus of an atom together.
To know more about Proton:
https://brainly.com/question/14604678
#SPJ6
Look at the diagram below. The value of equivalent resistor is: A. 4 Ω B. 6 Ω C. 8 Ω D. 10 Ω
Answer:
R=4Ω
Explanation:
R1 and R3 are parrallel
so we have : R=R1*R2/R1+R2
R=6*3/6+3
R=18/9
R=2Ω
R2 and 2Ω are in series,so we have
R=R2+2
R=2+2
R=4Ω
Water floats on a liquid called "carbon tetrachloride." The two liquids do not mix. A light ray passing from water into carbon tetrachloride has an incident angle of 45.0° and an angle of refraction of 40.1°. If the index of refraction of water is 1.33, what is the index of refraction of carbon tetrachloride?
Answer:
1.26
Explanation:
[tex]index \: of \: refraction \: = \: \ \frac{ \sin(angle \: of \: incidence) }{ \sin(angle \: of \: refraction) } [/tex]
[tex] \frac{ \sin(45.0) }{ \sin(40.1) } [/tex]
= 1.26
Refractive index is defined as the ratio of speed of light in the vacuume and in the medium.The index of refraction of carbon tetrachloride is 1.26.
Refractive index:
It is defined as the ratio of speed of light in the vacuume and in the medium.
[tex]\bold { n={\dfrac {c}{v}}}[/tex]
where
c -speed of light in vacuum
v - phase velocity of light in the medium.
It can also be calculated by the angle of refration,
[tex]\bold { n={\dfrac {sin\ i}{sin\ r}}}[/tex]
Where,
Sin i - angle of incidence = 45.0
sin r - angle of refraction = 40.1
Put the values in the formula,
[tex]\bold { n= {\dfrac {45.0}{40.1 }}}\\\\\bold { n= 1.26}[/tex]
Thereforew, the index of refraction of carbon tetrachloride is 1.26.
To know more about index of refraction,
https://brainly.com/question/4084792
How do FITT principles help you on your sports related activity
Answer:
F.I.T.T. stands for frequency, intensity, time and type. These four key aspects of your workout program will help you achieve your athletic goal, whether it's to increase your endurance, strength or speed. Here is an in-depth look at what each means and how to modify it to make athletic gains on the field...
How has the games changed over the years?
Answer:
The definition of the particular circumstance consists provided in the subsection on the interpretation elsewhere here.
Explanation:
Throughout the past 10-20 years, the computer games industry is experiencing some insane shifts. Several of the adjustments are responsible for the observed market developments, while others are related to just the tech boom as well as technological development across the global economy. Here is another glimpse at some instances of how and why the gaming industry has evolved in just the last few decades.What is the density of a 15 kg block of wood with a volume of 1.5 cubic meters;
d=m/v?
A)10
B)150
C)20
Answer: A) 10
Explanation:
I plugged in the numbers into a calculator.
Ex:
The formula for density is d=m/v so I divided 15 by 1.5 and it gave me 10.
Which value would complete the last cell?
(1 point)
3.0
100.0
25.0
4.0
Answer:
4.0
Explanation:
The following data were obtained from the question:
Force (F) = 20 N
Mass (m) = 5 kg
Acceleration (a) =.?
Force is simply defined as the product of mass and acceleration. Mathematically, it is expressed as
Force (F) = mass (m) x acceleration (a)
F = ma
With the above formula, we can obtain th acceleration of the body as follow:
Force (F) = 20 N
Mass (m) = 5 kg
Acceleration (a) =.?
F = ma
20 = 5 x a
Divide both side by 5
a = 20/5
a = 4 m/s²
Therefore, the value that will complete the last cell in the question above is 4.
When the hydraulic conductivity Ks = 10 mm/hr; effective matrix potential Ns = 20 mm, and rainfall intensity I = 30 mm/hr , determine the amount of runoff generated when the runoff rate reaches 15 mm/hr?( 2.7 mm or 0.21 mm or 18 mm or 0.67 mm)
Answer:
[tex]t = 0.75 \ hr = 0.75 *60 = 45 \ minutes[/tex]
Explanation:
From the question we are told that
The hydraulic conductivity is [tex]Ks = 10\ mm/hr[/tex]
The effective matrix potential [tex]Ns = 20 \ mm[/tex]
The intensity of rainfall is [tex]I = 30 \ mm/hr[/tex]
The runoff rate [tex]R = 15 \ mm/hr[/tex]
Generally the run off rate is mathematically represented as
[tex]R = (I - Ks) t[/tex]
Here t is the amount of runoff generated
=> [tex]15 = (30 - 10) t[/tex]
=> [tex]t = 0.75 \ hr[/tex]
converting to minutes
[tex]t = 0.75 \ hr = 0.75 *60 = 45 \ minutes[/tex]
A disk-shaped dough is initially spinning at 2 rotations per second (1 rotation = 360°). As time goes on, it slowly deforms, and is now spinning at a different angular speed. The dough changed radius from 16 cm to 17 cm, and its mass remained constant throughout. What is its final angular speed in degrees/s?
Answer:
10.44° per sec
Explanation:
Initial angular speed N = 2 rotations per minute
converting to rad/s ω = 2πN/60 = (2 x 3.142 x 2)/60 = 0.21 rad/s
the initial radius of the disk = 16 cm = 0.16 m
final radius = 17 cm = 0.17 m
Angular momentum = [tex]I[/tex]ω
where [tex]I[/tex] = rotational inertia = mass x [tex]radius^{2}[/tex]
ω = angular speed
For the initial case
[tex]I[/tex] = m x [tex]0.16^{2}[/tex] = 0.0256m
Angular momentum = 0.0256m x 0.21 = 0.0054m
For second case
[tex]I[/tex] = m x [tex]0.17^{2}[/tex] = 0.0289m
Angular momentum = 0.0289m x ω = 0.0289mω
For conservation of rotational momentum, initial angular momentum must be equal to the final angular momentum
0.0054m = 0.0289mω
m cancels out, we have
0.0054 = 0.0289ω
ω = 0.187 rad/s
converting back to rpm, we have
N = 0.187/2π = 0.029 rotations per sec
0.029 x 360 = 10.44° per sec
1
A force 2ON acts at a distance of 2n from a pivot.
what is the moment
force about the pivot
Answer:
[tex]\large \boxed{\mathrm{40 \ Nm}}[/tex]
Explanation:
[tex]\sf Moment \ (Nm) = Force \ (N) \times Distance \ from \ pivot \ (m)[/tex]
[tex]M=20 \times 2[/tex]
[tex]M=40[/tex]
Compared to other planets in the solar system, Earth has a wider range of temperature conditions, which contributes to Earth's ability to support life.
Answer:
Goldilocks zone of habitability.
Explanation:
Earth is the third planet in the solar system next to venus and is followed by mars as the red planet. Due to the nature and characteristics of the earth its called the blue planet as it supports life and this is possible due to the presence of the adequate temperatures and pressure conditions that were created some 4 billion years ago. The earth has an adequate amount of temperature that is considered to be sufficient for life on the planet to exist and is called the goldilocks zone. As the earth is neither too far nor too close to the sun.You put a piece of ice into a glass of lemonade at room temperature. Which statements explains the heat flow in this scenario? A. Heat flows in both directions. B. Heat flows from the ice to the lemonade. C. Heat flows from the lemonade to the ice. D. Heat flows from the ice to the lemonade to the glass.
Answer:
C. Heat flows from lemonade to the ice
Explanation:
Transfer of heat from the drink to the ice is what melts the ice and cools the drink.
What evidence supported the inflation theory? (the big bang theory one pls)
Answer:
The comic microwave background
Explanation:
The cosmic microwave background is said to be part of the remnant of the Big Bang that happened which resulted in the formation of the universe. This is because the universe was thought to be a very hot place which resulted in the expansion of it.
The heat was said to have resulted in the cooling of gases present and the remnant of the heat is what formed the radiation called the cosmic wave background.
Be careful of the wire size application chart you use, because many of them allow up to a ____ voltage drop over the length of the wire, which is more than is allowed in most automotive circuits. Group of answer choices
Answer: 0.1
Explanation: The wire size is very important when making decisions on the wiring of any equipment,house and other things. It has also been found that the size of the wire determines the load that can be allowed through it.
The right wire size application chart should always be considered before selecting the wiring diagram or system for any building or equipment as it can help to determine the amount of voltage that can be effectively carried through it.
If you go to a nutrition store and buy a supplement you can count on the fact that it is pure and safe because supplements are regulated controlled and inspected by the FDA
Answer:
The answer is False.
Explanation: The FDA (food and drug administration) is a regulatory agency of the United state Government, they regulate the production and distribution of food and drugs within the United States of America, ensuring that standards are met and followed.
Most of the approvals given to food and drugs by FDA are done based on random sampling of products which may not be able to capture all the defective products in a given lot or batch of supplies, which is why it very necessary to take other measures to verify the wholesomeness, authenticity etc of a given product before purchasing or making use of such products.
Answer:
false
Explanation:
got right on egd
The quantum state of a particle can be specified by giving a complete set of quantum numbers (n,l, ml,ms). How many different quantum states are possible if the principal quantum number is n=3?
Explanation:
We need to find the quantum state of a particle can be specified by giving a complete set of quantum numbers (n,l, ml,ms).
We have the principal quantum number, n = 3
The value of l = n-1
l = 0,1,2,3
The value of [tex]m_l[/tex]
[tex]m_l=-l\ \text{to}\ +l\\\\m_l=-3,-2,-1,0,1,2,3[/tex]
The value of [tex]m_s[/tex]
[tex]m_s=\dfrac{-1}{2},\dfrac{+1}{2}[/tex]
Hence, this is the required solution.
Every time Dylan takes his dog Frisbee for a walk, the dog always pulls hard on the leash. This nearly pulls Dylan's arm out of its socket and Frisbee almost chokes himself! Explain these effects in terms of Newton's third law.
Answer:
See explanation below for Newton's third law of "action generates reaction" for this example
Explanation:
From Newton's third law: "For every action there is an equal and opposite reaction."
Frisbee is pulling on the leash with force F which is felt by Dylan as a tension force in the leash trying to pull his arm out of its socket, and Frisbee feels an equal and opposite tension force from the leash chocking him.
A round steel plate with a diameter of 20 cm is supplied with heat in such a way that its temperature changes from 22 ° C to 150 ° C. How much does its area increase?
Answer:
1.05×10⁻⁴ m²
Explanation:
ΔA = 2 A₀ α ΔT,
where ΔA is the change in area,
A₀ is the initial area,
α is the linear expansion coefficient,
and ΔT is the change in temperature.
A₀ = π (0.20 m / 2)² = 0.0314 m².
For steel, α = 13×10⁻⁶ /°C.
ΔT = 150°C − 22°C = 128°C.
ΔA = 2 (0.0314 m²) (13×10⁻⁶ /°C) (128°C)
ΔA = 1.05×10⁻⁴ m²
Hi please, I Have An attachment on Waves, Just two Objective Questions Whoever Answers Will be Marked Brainliest thank you.
Answer:
The first answer is W and Z, since they appear to be a period apart. Dont know the second question. I did what I could, hope someone can answer the second.
A physical inventory on December 31 shows 3500 units on hand. Bonita sells the units for $15 each. The company has an effective tax rate of 20%. Bonita uses the periodic inventory method. The weighted-average cost per unit is
A bullet of mass m, moving horizontally with speed u, meets a block of wood of mass M, travelling along the same line but in the opposite direction with speed ,U, and remains embedded in it. Show that the loss of kinetic energy is of the form 1/2kMm, where k is in terms of u, U, m, M and find the loss in KE when the bullet of mass 4.0g, travelling at 890ms^-1 hits a block of wood, mass 4.0kg moving at 7.0ms^-1
Answer:
Explanation:
First of all we shall calculate the velocity of composite mass . Let it be v . Applying law of conservation of momentum
mu - MU = ( m + M ) v
v = mu - MU / ( m + M )
loss of kinetic energy
= 1/ 2 mu² + 1/2 MU² - 1/2 ( M +m ) v²
= 1/ 2 mu² + 1/2 MU² - 1/2 ( M +m ) (mu - MU)² / ( m + M )²
= 1/ 2 mu² + 1/2 MU² - 1/2 (mu - MU)² / ( m + M )
= 1/2 [ m²u² + mMu² +mMU² + m²U² - m²u² - M²U² - 2 muMU ] / ( m + M )
= 1 / 2 [ mMu² + mMU² - 2 muMU ] / ( m + M )
= 1 / 2mM [ (u² + U² - 2 uU) / ( m + M )]
= 1/2 mM x k
where
k = [ (u² + U² - 2 uU) / ( m + M )]
Given
m = .004 kg
M = 4 kg
u = 890 ms⁻¹
U = 7 ms⁻¹
k = ( 890² + 7² - 2 x 890 x 7 ) / 4.004
= ( 792100 + 49 - 12460 ) / 4.004
= 194727.52
loss of kinetic energy
= 1/2 mM x k
= .5 x .004 x 4 x 194727.52
= 1557.82 J .
Suppose that you have been chosen for a space mission to a distant planet. Due to the length of time you'll be away from Earth you must carry out physical activity every day. On earth your, strength and conditioning trainer has determined you must do 90 minutes of exercise every day. If the vehicle is travelling at 0.80 c how much time, according to a timer on the space vehicle should you be active to meet your physical activity requirement?
Answer:
I should be active for 15 hours to meet the physical activity requirement.
Explanation:
Since time dilates in moving objects, we use the formula t = t₀/√(1 - β²) where t = time in space vehicle, t₀ = time on earth = 9 hours and β = v/c where v = speed of space vehicle = 0.8c.
So, t = t₀/√(1 - β²)
t = 9/√(1 - (v/c)²)
= 9/√(1 - (0.8c/c)²)
= 9/√(1 - (0.8)²)
= 9/√(1 - (0.64)
= 9/√0.36
= 9/0.6
= 15 hr
So, according to a timer on the space vehicle, I should be active for 15 hours to meet the physical activity requirement.
An object is to be dropped from an aeroplane so as to hit a target on the ground. If the aeroplane is travelling horizontally at 80m/s at a height of 2000m, calculate the position of the aeroplane when the object is released
Answer:
you live it will be around 23 to 82% angle
Explanation:
just think about yourself going in the high-speed and then jumping and then just think of all know that person just jumping without being going to high speed
(a) Calculate the rate of heat conduction through house walls that are 13.0 cm thick and that have an average thermal conductivity twice that of glass wool. Assume there are no windows or doors. The surface area of the walls is 120 m2 and their inside surface is at 18.0 oC, while their outside surface is at 5.0 oC. (b) How many 1-kW room heaters would be needed to balance the heat transfer due to conduction
Answer:
a. 960 W b. One 1 kW room heater
Explanation:
a. The rate of heat conduction P = kA(T₂ - T₁)/d where k = 2 × 0.040 W/m-K = 0.080 W/m-K since the thermal conductivity of glass wool is 0.040 W/m-K and that of the material is twice the thermal conductivity of glass wool, A = area of walls = 120 m², T₁ = outside surface temperature = 5.0 °C, T₂ = inside surface temperature = 18.0 °C and d = thickness of wall = 13.0 cm = 0.13 m
P = kA(T₂ - T₁)/d
= 0.080 W/m-K × 120 m²(18.0 °C - 5.0 °C)/0.13 m
= 9.6 Wm/K × 13 K/0.13 m
= 124.8 Wm/0.13 m
= 960 W
b. The number of 1 kW room heater required will be
n = rate of heat conduction/power of one room heater = 960 W/ 1 kW = 960 W/1000 W = 0.96 ≅ 1
So we need only one 1 kW room heater.
