Car tires are generally considered insulators because they have a very high resistance to the flow of electricity. Insulators are materials that do not allow electric current to flow through them easily.
A substance that conducts heat or energy poorly is known as an insulator. It is a material that has a high electrical resistance, which means that it resists the passage of electric current through it. In electrical circuits, insulators are used to isolate conductors from one another and stop electricity from flowing between them.
Since it prohibits electrons from moving easily through it and has a very high resistivity, the rubber used in car tires functions well as an insulator. This makes it difficult for electric current to pass through the tire, lowering the possibility of electric shock and helping to avoid static electricity buildup.
To know more about tires:
https://brainly.com/question/17407784
#SPJ4
A student wants to use the output from the aux port on their phone to play music from their speakers. The aux port supplies 5v and a max current of 0.015A, but the speakers need 12v and a max current of 1.5A. You decide to use a power transistor to amplify the signal from the aux port. What does the beta value of your chosen transistor need to be to amplify the current enough?
pls explain or elaborate the answer if u can!!
Answer:The beta value of a transistor represents the current gain, which is the ratio of the collector current to the base current. In this case, we want to use the transistor as an amplifier to increase the current from the 0.015A supplied by the phone to the 1.5A required by the speakers.
The required current gain can be calculated using the following formula:
Beta = (Ic / Ib)
Where:
Beta is the current gain of the transistor
Ic is the collector current (output current)
Ib is the base current (input current)
To find the required beta value, we need to first calculate the base current required to drive the transistor. We can use Ohm's Law to do this:
Ib = V / R
Where:
Ib is the base current
V is the voltage supplied by the phone (5V)
R is the input resistance of the transistor circuit
Assuming an input resistance of 1kΩ, the base current required is:
Ib = V / R = 5 / 1000 = 0.005A (5mA)
Now, we can calculate the required collector current using the maximum current required by the speakers:
Ic = 1.5A
Finally, we can calculate the required beta value:
Beta = Ic / Ib = 1.5 / 0.005 = 300
Therefore, we need to choose a power transistor with a beta value of at least 300 to amplify the current from the aux port enough to drive the speakers.
Explanation:
A small block with mass 0.0400 kg slides in a vertical circle of radius R = 0.500 m on the inside of a circular track. During one of the revolutions of the block, when the block is at the bottom of its path, point A, the normal force exerted on the block by the track has magnitude 3.95 N. In this same revolution, when the block reaches the top of its path, point B, the normal force exerted on the block has magnitude 0.680 N. How much work is done on the block by friction during the motion of the block from point A to point B?
The work done on the block by friction during the motion of the block from point A to point B is 2.49 J.
The normal force acting on the block at point A and point B is different. We can find the weight of the block at points A and point B using the following formula:
Weight = mg,
where m is the mass of the block and g is the acceleration due to gravity.
Weight at point A = m × g
Weight at point B = m × g
Now, the normal force acting on the block at point A is given as 3.95 N.
Therefore, we can write the equation for the weight and normal force as:
Weight at point A - Normal force at point A = m × a
Now, at point A, the acceleration acting on the block is the centripetal acceleration a = v²/R where v is the velocity of the block at point A.
We can write the equation for the weight and normal force as:
m × g - 3.95 = m × v²/R
Similarly, at point B, we can write the equation for the weight and normal force as:
m × g - 0.680 = m × v²/R
Now, we can solve both the equations for the velocity of the block at point A and point B:
Velocity at point A, v₁ = √(gR - 3.95/m)
Velocity at point B, v₂ = √(gR - 0.680/m)
The change in kinetic energy during the motion from point A to point B is given by:
∆KE = KE₂ - KE₁
= (1/2)mv₂² - (1/2)mv₁²
We know that work done, W = ∆KE
So, the work done on the block by friction during the motion of the block from point A to point B is given by:
W = (1/2)m(v₂² - v₁²)
Substituting the values in the above equation:
W = (1/2) × 0.0400 × ((√(9.81 × 0.500 - 0.680/0.0400))² - (√(9.81 × 0.500 - 3.95/0.0400))²)
W = 2.49 J
Therefore, the work done on the block by friction is 2.49 J.
Learn more about Friction here:
https://brainly.com/question/24338873
#SPJ11
b) If the observation point on the z axis is far enough away from the center of this ring, the ring should start to look and behave as a particle of charge Q at the origin. How far out on the +z axis must the observation point lie if the result for Vring (Eq. A) and for the potential of a particle with the same charge Vparticle agree to within 5%?
The potential due to a ring of charge at a point on the z-axis a distance z away from the center of the ring is given by the equation:
Vring = kQ / √(R^2 + z^2)
where k is Coulomb's constant, Q is the charge on the ring, R is the radius of the ring, and z is the distance from the center of the ring to the observation point.
If the ring behaves like a point particle of charge Q at the origin, the potential at the same observation point on the z-axis would be:
Vparticle = kQ / z
To find the distance z where these two potentials agree to within 5%, we can set up the following equation:
|Vring - Vparticle| / Vparticle ≤ 0.05
Substituting the expressions for Vring and Vparticle and simplifying, we get:
|√(R^2 + z^2) - z| / z ≤ 0.05
Squaring both sides and rearranging, we get:
(R^2 / z^2) ≤ 0.0025
Taking the square root of both sides, we get:
R / z ≤ 0.05
Solving for z, we get:
z ≥ R / 0.05
Therefore, the observation point on the +z axis must be at a distance z of at least R / 0.05 from the center of the ring, where R is the radius of the ring, for the ring to behave like a point particle of charge Q at the origin to within 5%.
For more questions like charge visit the link below:
https://brainly.com/question/30510441
#SPJ11
lab 4: newton's second law: the atwood machine pre-lab questions: 1. what happens to the acceleration of our system when the mass of the system increases but the net force stays constant? 2. what happens to the acceleration of our system when the net applied force increases but the mass of the system does not change? 3. explain, in your own words, potential sources of error in today's experiment.
According to Newton's second law, the acceleration of a system is directly proportional to the net force applied to it and inversely proportional to its mass. Therefore, if the net force stays constant but the mass of the system increases, the acceleration of the system will decrease.
Similarly, if the mass of the system remains constant but the net applied force increases, the acceleration of the system will increase.
There are several potential sources of error in the Atwood machine experiment. For example, friction in the pulley or air resistance could cause the system to accelerate at a different rate than predicted by theory. Additionally, the masses used in the experiment may not be perfectly accurate, which could introduce small errors into the measurements. The string connecting the two masses could also stretch or have varying elasticity, which could affect the results. Finally, human error in measuring the time or the distances traveled by the masses could lead to inaccuracies in the calculated values of acceleration or tension in the string.
for more such question on acceleration
https://brainly.com/question/10425898
#SPJ11
what is the minimum angular velocity (in rpm ) for swinging a bucket of water in a vertical circle without spilling any? the distance from the handle to the bottom of the bucket is 35 cm . express your answer in revolutions per minute.
The minimum angular velocity (in rpm) for swinging a bucket of water in a vertical circle without spilling any is 5.56 rpm.
The minimum angular velocity (in rpm) for swinging a bucket of water in a vertical circle without spilling any is given by the formula; Vmin=√g/R
where:
Vmin = minimum angular velocity (in rpm)g = acceleration due to gravity (9.81 m/s²)R = radius of the circular path or distance from the handle to the bottom of the bucket (35 cm)To express the answer in revolutions per minute, the radius of the circle must be converted to meters;R = 35 cm = 0.35 m
Substituting the values given above into the formula;
Vmin=√g/R Vmin=√9.81/0.35 Vmin = 5.56 rpmTherefore, the minimum angular velocity (in rpm) for swinging a bucket of water in a vertical circle without spilling any is 5.56 rpm.
Learn more about velocity: https://brainly.com/question/25749514
#SPJ11
X-ray pulses from Cygnus X-1, a celestial x-ray source, have been recorded during high-altitude rocket flights. The signals can be interpreted as originating when a blob of ionized matter orbits a black hole with a period of 7.84 ms. If the blob were in a circular orbit about a black hole whose mass is 13.5 times the mass of the Sun, what is the orbit radius? The value of the gravitational constant is 6.67259×10−11N⋅m2/kg2 and the mass of the Sun is 1.991×1030 kg. Answer in units of km.
The orbit radius is 6.225 × 10^5 km.
The x-ray pulses from Cygnus X-1, a celestial x-ray source, have been recorded during high-altitude rocket flights. The signals can be interpreted as originating when a blob of ionized matter orbits a black hole with a period of 7.84 ms. And also, it is given that the blob were in a circular orbit about a black hole whose mass is 13.5 times the mass of the Sun. We need to determine the orbit radius.
The formula to be used to find the orbit radius is given by:
G(M+m)T2/4π2= r3
Where,
G = Gravitational constant = 6.67259×10−11 N⋅m2/kg2
M = Mass of the black hole
m = Mass of the blob
T = Time period of the orbit = 7.84 ms = 7.84 × 10^-3 s
r = Orbit radius
Substitute the given values in the above formula, we get:
r3 = G(M+m)T2/4π2
r3 = 6.67259×10−11 * [13.5(1.991×10^30) + m] * (7.84×10−3)2 / 4π2
r3 = 5.7919 × 10^15 m^3
Taking cube root on both sides, we get:
r = [5.7919 × 10^15 m^3] 1/3
r = 6.225 × 10^8 m
1 km = 1000 m
Therefore, the orbit radius in km is:
r = 6.225 × 10^8 m * 1 km / 1000 m
r = 6.225 × 10^5 km
Hence, the orbit radius is 6.225 × 10^5 km.
To know more about Cygnus X-1, refer here:
https://brainly.com/question/15705839#
#SPJ11
Which of the following correctly compares the Sun's energy generation process to the energy generation process in human-built nuclear power plants?
Both processes involve nuclear fusion, but the Sun fuses hydrogen while nuclear power plants fuse uranium.
The Sun generates energy by fusing small nuclei into larger ones, while our power plants generate energy by the fission (splitting) of large nuclei.
The Sun generates energy through nuclear reactions while nuclear power plants generate energy through chemical reactions.
The Sun generates energy through fission while nuclear power plants generate energy through fusion.
The correct comparison of the energy generation processes is "The Sun generates energy by fusing small nuclei into larger ones, while our power plants generate energy by the fission (splitting) of large nuclei". Thus, the correct options are A and B.
What is Nuclear power?Nuclear reactions involve the alteration of an atom's nucleus in both cases. Nuclear power plants and the sun both use energy generated by these nuclear reactions to produce electricity. The difference is in the type of nuclear reaction that takes place.
In the Sun, nuclear fusion is the process by which atomic nuclei of low atomic number fuse to form a heavier nucleus with the release of energy. The energy produced in this way is what makes the Sun so hot and bright. In a nuclear power plant, nuclear fission is the process by which the nucleus of an atom is split into two smaller nuclei.
The energy that is released in the process is used to heat water, creating steam that drives a turbine, which in turn drives a generator to produce electricity.
Therefore, the correct options are A and B.
Learn more about Nuclear power here:
https://brainly.com/question/18769119
#SPJ11
A straight 2.40 m wire carries a typical household current of 1.50 A (in one direction) at a location where the earth's magnetic field is 0.550 gauss from south to north. *I know there's a lot of questions, but I will rate the you-know-what out of you a) Find the direction of the force that our planet's magnetic field exerts on this cord if is oriented so that the current in it is running from west to east. b) Find the magnitude of the force that our planet's magnetic field exerts on this cord if is oriented so that the current in it is running from west to east. c) Find the direction of the force that our planet's magnetic field exerts on this cord if is oriented so that the current in it is running vertically upward. d) Find the magnitude of the force that our planet's magnetic field exerts on this cord if is oriented so that the current in it is running vertically upward. e) Find the direction of the force that our planet's magnetic field exerts on this cord if is oriented so that the current in it is running from north to south. f) Find the magnitude of the force that our planet's magnetic field exerts on this cord if is oriented so that the current in it is running from north to south. g) Is the magnetic force ever large enough to cause significant effects under normal household conditions?
a) If the current is running from west to east, the force that our planet's magnetic field exerts on this cord is directed upwards
b) The magnitude of the force that our planet's magnetic field exerts on this cord if it is oriented so that the current in it is running from west to east is F =2.64 x 10^-4 N
c) If the current is running vertically upward, the force that our planet's magnetic field exerts on this cord is directed to the left. west
d) The magnitude of the force that our planet's magnetic field exerts on this cord if it is oriented so that the current in it is running vertically upward is F = 0 zero
e) If the current is running from north to south, the force that our planet's magnetic field exerts on this cord is directed east.
f) The magnitude of the force that our planet's magnetic field exerts on this cord if it is oriented so that the current in it is running from north to south is F = 2.64 x 10^-4 N
g) The magnetic force is not large enough to cause significant effects under normal household conditions.
EXPLANATION
a) The direction of the force that our planet's magnetic field exerts on the cord is perpendicular to both the direction of the current and the direction of the magnetic field, according to the right-hand rule. In this case, if the current is running from west to east, and the magnetic field is from south to north, the force will be directed upwards.
b) The magnitude of the force can be calculated using the formula:
F = BIL sin(theta)
where B is the magnitude of the magnetic field, I is the current, L is the length of the wire, and theta is the angle between the direction of the current and the direction of the magnetic field. In this case, theta is 90 degrees, so sin(theta) = 1. Substituting the given values, we get:
F = (0.550 x 10^-4 T) x (1.50 A) x (2.40 m) x 1
= 2.64 x 10^-4 N
Therefore, the magnitude of the force is 2.64 x 10^-4 N.
c) If the current in the wire is running vertically upward, the force will be directed towards the west.
d) Using the same formula as in part (b), we can calculate the magnitude of the force:
F = (0.550 x 10^-4 T) x (1.50 A) x (2.40 m) x sin(90)
= 0
Therefore, the magnitude of the force is zero.
e) If the current in the wire is running from north to south, the force will be directed towards the east.
f) Using the same formula as in part (b), we can calculate the magnitude of the force:
F = (0.550 x 10^-4 T) x (1.50 A) x (2.40 m) x 1
= 2.64 x 10^-4 N
Therefore, the magnitude of the force is 2.64 x 10^-4 N.
g) The magnitude of the magnetic force in this case is quite small, and under normal household conditions, it is unlikely to cause significant effects. However, in some situations, such as in electrical power transmission systems, the effects of the magnetic force may need to be taken into account.
For more such questions on magnetic field
https://brainly.com/question/13689629
#SPJ11
write the equations for the balance of the forces in the horizontal and vertical directions for block a and for block b (four equations). start with the force exerted on block a in the horizontal direction.
The equations for the balance of forces in the horizontal and vertical directions for Block A and Block B are: Horizontal direction of Block A: T = 12.5 N,Vertical direction of Block A: W = 24.5 N,Horizontal direction of Block B: T = 22.5 N and Vertical direction of Block B: W = 44.1 N.
The forces acting on Block A are: Force of tension (T) and Force of gravity (W).The forces acting on Block B are: Force of tension (T) and Force of gravity (W).For Block A in the horizontal direction, the force exerted will be the force of tension (T).
Therefore: Horizontal direction of Block A: T = mA a ………………….. (1) For Block A in the vertical direction, the force exerted will be the force of gravity (W).
Therefore: Vertical direction of Block A: W = mA g ………………….. (2) For Block B in the horizontal direction, the force exerted will also be the force of tension (T).
Therefore: Horizontal direction of Block B: T = mB b ………………….. (3) For Block B in the vertical direction, the force exerted will be the force of gravity (W).
Therefore: Vertical direction of Block B: W = mB g ………………….. (4)
The equations can be solved by substituting the values of the masses and the acceleration due to gravity. Therefore, equations (1) to (4) will become:
Horizontal direction of Block A: T = 2.5 (5) = 12.5 N Vertical direction of Block A: W = 2.5 (9.8) = 24.5 N Horizontal direction of Block B: T = 4.5 (5) = 22.5 N Vertical direction of Block B: W = 4.5 (9.8) = 44.1 N
Therefore, the equations for the balance of forces in the horizontal and vertical directions for Block A and Block B are:
Horizontal direction of Block A: T = 12.5 N Vertical direction of Block A: W = 24.5 N Horizontal direction of Block B: T = 22.5 N Vertical direction of Block B: W = 44.1 N
More on forces: https://brainly.com/question/14932990
#SPJ11
a suspicious-looking man runs as fast as he can along a moving sidewalk from one end to the other, taking 2.00 s. then security agents appear, and the man runs as fast as he can back along the sidewalk to his starting point, taking 12.6 s. what is the ratio of the man's running speed to the sidewalk's speed?
The ratio of the man's running speed to the sidewalk's speed is 6.3.
To solve the problem, we can start by using the formula:
distance = speed × time
Let's assume that the length of the moving sidewalk is L, and the speed of the man is v and the speed of the sidewalk is u.
When the man runs along the sidewalk from one end to the other, his speed relative to the ground is (v + u), and the distance he covers is L. Therefore, we have:
L = (v + u) × 2.00 s
When the man runs back along the sidewalk to his starting point, his speed relative to the ground is (v - u), and the distance he covers is also L. Therefore, we have:
L = (v - u) × 12.6 s
Now we can solve for v/u by dividing the two equations:
(v + u)/(v - u) = 2.00/12.6
Solving for v/u gives:
v/u = (2.00/12.6 + 1)/(2.00/12.6 - 1) = 6.3
Therefore, the ratio of the man's running speed to the sidewalk's speed is 6.3.
For more similar questions on distance:
brainly.com/question/12356021
#SPJ11
The electric flux through a spherical surface is4.3×104 N⋅m2/C. What is the net charge enclosed by the surface? The net charge enclosed by the surface isμC. The electric flux through a cubical box34 cmon a side is7.5×103 N⋅m2/C. What is the total charge enclosed by the box? The total charge enclosed by the box isμC
For the electric flux through a spherical surface is 4.3 x 10⁴ N⋅m²/C, then the net charge enclosed by the surface is μC, and for the electric flux through a cubical box 34 cm on a side is 7.5 x 10³ N⋅m²/C, the total charge enclosed by the box is μC.
The electric flux through a spherical surface is 4.3 x 10⁴ N⋅m²/C.
The net charge is Electric Flux = Charge / Surface Area,
so the net charge enclosed is 4.3 x 10⁴ / (4πr²) where r is the radius of the sphere.
Therefore, the net charge enclosed by the surface is μC.
The electric flux through a cubical box 34 cm on a side is 7.5 x 10³ N⋅m²/C.
The total charge is Electric Flux = Charge / Surface Area,
so the total charge enclosed is 7.5 x 10³ / (6a²)
where a is the length of one side of the cube.
Therefore, the total charge enclosed by the box is μC.
Learn more about electric flux here:
https://brainly.com/question/2664005
#SPJ11
Rank the objects from left to right based on their average distance from the Sun, from farthest to closest. (Not to scale.)Pluto, Saturn, Jupiter, Mars, Earth, Mercury
From farthest to closest, the ranking of the planets based on their average distance from the Sun would be:
Pluto, Saturn, Jupiter, Mars, Earth, Mercury
Note that the objects are not to scale, so this ranking may not be perfectly accurate in terms of relative distances. However, it gives a general idea of the order of the planets from farthest to closest to the Sun.
The eight planets in our solar system, listed in order from the Sun, are:
Mercury
Venus
Earth
Mars
Jupiter
Saturn
Uranus
Neptune
These eight planets are also known as the "classical planets," and are the largest and most massive objects in orbit around the Sun. There are also several dwarf planets in our solar system, such as Pluto and Ceres, as well as numerous smaller objects like asteroids and comets.
Learn more about planets:
https://brainly.com/question/11023671
#SPJ11
does air move from areas of high pressure to low pressure
Explanation: Gases move from high-pressure areas to low-pressure areas. And the bigger the difference between the pressures, the faster the air will move from the high to the low pressure.
write an expression for the magnitude of the force, f, exerted on the firefighter by the pole. answer in terms of the variables from the problem statement as well as g for the acceleration due to gravity.
The expression for the magnitude of the force exerted on the firefighter by the pole can be expressed as F = mg + ma.
Where m is the mass of the firefighter,
g is the acceleration due to gravity, and
a is the acceleration of the pole
In order to find an expression for the magnitude of the force, F, exerted on the firefighter by the pole, we need to consider the forces acting on the firefighter.
According to Newton's second law of motion, the force acting on an object is equal to its mass multiplied by its acceleration. In this case, the forces acting on the firefighter are the gravitational force, which is pulling the firefighter downwards with a force of mg, and the force exerted on the firefighter by the pole, which is pushing the firefighter upwards with a force of ma. Therefore, the total force acting on the firefighter is given by the sum of these two forces, which is: F = mg + ma
Thus, this expression gives us the magnitude of the force exerted on the firefighter by the pole. Here, m is the mass of the firefighter, g is the acceleration due to gravity, and a is the acceleration of the pole. if the pole is not accelerating (i.e., if a = 0), then the expression reduces to F = mg, which is the gravitational force acting on the firefighter.
To know more about Magnitude please visit :
https://brainly.com/question/30337362
#SPJ11
a flat, circular loop has 17 turns. the radius of the loop is 12.5 cm and the current through the wire is 0.60 a. determine the magnitude of the magnetic field at the center of the loop (in t).
The magnetic field at the center of the loop is calculated to be 0.159 T.
The magnetic field at the center of a flat, circular loop with 17 turns, a radius of 12.5 cm, and a current of 0.60 A can be determined by using the equation B = µ₀.n.I/2.π.r, where
B is the magnitude of the magnetic field, µ₀ is the permeability of free space, n is the number of turns, I is the current, and r is the radius of the loop.Using this equation, the magnetic field at the center of the loop is calculated to be 0.159 T.
Learn more about magnitude of the magnetic field: brainly.com/question/30640184
#SPJ11
a cross section across a diameter of a long cylindrical conductor of radius a=2 cm carrying uniform current 170 A. What is the magnitude of the current's magnetic field at radial distance (a) 0, (b) 1 cm, (c) 2 cm (wire's surface), and (d) 4 cm
The magnitude of the current's magnetic field at radial distances (a) 0, (b) 1cm, (c) 2cm (wire's surface), and (d) 4cm are undefined, 1.7 * 10^-3 Tesla, 1.7 * 10^-3 Tesla, and 8.5 * 10^-4 Tesla, respectively.
The question is about finding the magnitude of magnetic fields at different radial distances across a diameter of a long cylindrical conductor of radius a=2 cm carrying uniform current 170A.
Let's solve it step by step.
(a) At radial distance 0:
At the center of the conductor, r = 0, the magnetic field is zero.
It can be found by using the formula for the magnetic field at the center of the wire:
B = (μ_0 * I) / (2 * π * r)
= (4π * 10^-7 * 170) / (2π * 0)
= undefined.
Therefore, the magnetic field at r = 0 is undefined.
(b) At radial distance 1cm:
Using the formula for the magnetic field at a point P located at a radial distance r from the center of the wire:
B = (μ_0 * I) / (2 * π * r)
= (4π * 10^-7 * 170) / (2π * 0.01)
= 1.7 * 10^-3 Tesla.
(c) At radial distance 2cm:
The magnetic field at r = a (i.e., the surface of the wire) can be determined by substituting the value of r = 2cm into the magnetic field formula:
B = (μ_0 * I) / (2 * π * r)
= (4π * 10^-7 * 170) / (2π * 0.02)
= 1.7 * 10^-3 Tesla.
(d) At radial distance 4cm:
Again, we use the formula for the magnetic field at a point P located at a radial distance r from the center of the wire:
B = (μ_0 * I) / (2 * π * r)
= (4π * 10^-7 * 170) / (2π * 0.04)
= 8.5 * 10^-4 Tesla.
For similar question on magnetic field
https://brainly.com/question/26257705
#SPJ11
What technological improvement in the 1920s allowed more goods to be produced at one time?
Automobile
Assembly line
Telephone
Motion picture
Answer: Telephone
Explanation:
The technological improvement that allowed more goods to be produced at one time in the 1920s was the development and widespread use of assembly line production. This was pioneered by companies such as Ford Motor Company, which introduced the assembly line to its automobile factories. The assembly line method allowed for the mass production of standardized products using specialized machines and workers performing specific tasks. By breaking down the manufacturing process into smaller, simpler tasks, and optimizing the movement of workers and materials, the assembly line significantly increased production efficiency and output. This led to the growth of mass production industries, increased affordability of goods, and a significant shift in the nature of work in the 20th century.
A student standing on the ground throws a ball straight up. The ball leaves the student's hand with a speed of 11 m/s when the hand is 1.8 m above the ground. How long is the ball in the air before it hits the ground? (The student moves her hand out of the way.)
The ball is in the air for about 1.8 seconds before it hits the ground after it leaves the student's hand with a speed of 11 m/s when the hand is 1.8 m above the ground.
Projectile motion is a kind of movement experienced by an object or particle (a projectile) that is projected near the Earth's surface and moves along a curved path under the gravity of the Earth. In general, projectile motion refers to a free-body's motion influenced only by gravity. A student throws a ball straight up while standing on the ground. When her hand is 1.8 m above the ground, the ball leaves her hand at a speed of 11 m/s. The time the ball is in the air before it hits the ground is calculated as follows:Using the equation:
∆y = v0yt + 1/2gt² Where ∆y is the displacement (in this case, -1.8 m) of the projectile along the vertical axis, v0y is the initial vertical velocity (in this case, 11 m/s), t is the time of flight, and g is the acceleration due to gravity (9.81 m/s²):-1.8 m = (11 m/s)t + (1/2)(-9.81 m/s²)t².Rearranging the equation, we get:-4.905t² + 11t - 1.8 = 0.
Using the quadratic formula, we get:t = (-11 ± sqrt(11² - 4(-4.905)(-1.8))) / (2(-4.905))= 1.77 s or t = 0.20 s. Since the ball is in the air for approximately 1.77 s before it hits the ground, and the student's hand is 1.8 m above the ground, the ball is in the air for about 1.8 seconds before it hits the ground. Therefore, the correct answer is the option C, 1.8 seconds.
More on Projectile motion: https://brainly.com/question/29325336
#SPJ11
f the initial energy of a conservative system is ei and the final energy is ef, what can we say about the relationship between these two energies in such a system?
In a conservative system, the total energy is conserved, which means that the initial energy (ei) is equal to the final energy (ef).
What are conservative system?Conservative systems are those where the total energy remains constant over time, such as in a pendulum swinging back and forth or a planet orbiting a star under the influence of gravity.
In such systems, the energy can be converted from one form to another, but the total amount of energy remains constant.
Therefore, we can say that in a conservative system, the initial energy (ei) and the final energy (ef) are equal. This means that any changes in the system's energy, such as potential energy being converted into kinetic energy, must be balanced by an equal and opposite change in some other form of energy, such as potential energy being converted into kinetic energy.
Learn more about conservation of energy here: https://brainly.com/question/166559
#SPJ1
A battery-powered toy car pushes a stuffed rabbit across the floor.Part ADraw a free-body diagram for a car (assume that it is moving from left to the right).Draw the force vectors with their tails at the dot. The orientation of your vectors will be graded. The exact length of your vectors will not be graded but the relative length of one to the other will be graded.Part BDraw a free-body diagram for a rabbit.Draw the force vectors with their tails at the dot. The orientation of your vectors will be graded. The exact length of your vectors will not be graded but the relative length of one to the other will be graded.
Part A: Thrust acts on the right in the direction of motion. Gravity acts downward.
Part B: The direction of air resistance is opposite to the direction of motion, which is shown towards the left. Gravity acts downwards.
Part A:
A free-body diagram for a car is as follows:
The direction of friction is opposite to the direction of motion, which is shown towards the left.
The diagram shows three forces acting on the toy car that is battery-powered, which is as follows:
The force due to friction is labeled as [tex]f_K[/tex].
The force of thrust is labeled as [tex]f_T[/tex]. The force of gravity is labeled as [tex]f_g[/tex].
Part B:
A free-body diagram for a rabbit is as follows:
The diagram shows three forces acting on the stuffed rabbit that is being pushed by a toy car that is battery-powered, which is as follows:
The direction of friction is opposite to the direction of motion, which is shown towards the right.
The force due to friction is labeled as [tex]f_K[/tex]. The force due to air resistance is labeled as fair. The force of gravity is labeled as [tex]f_g[/tex].
For similar question on Gravity
https://brainly.com/question/557206
#SPJ11
a test tube standing verticslly in a test tube rack contains 2.5 cm of oil and 6.5 cm of water. what is the pressur eon the bottom of the tube
The pressure on the bottom of the test tube which contain both the oil and water molecules is about 641.65 Pa + 220.725 Pa = 862.375 Pa.
What is the pressure in test tube?The pressure at the bottom of the test tube is the result of two factors: the weight of the oil and the weight of the water molecules. The pressure is equal to the density of each liquid multiplied by the height of each liquid, multiplied by the gravitational acceleration (g).
The pressure at the bottom of the test tube is given by the density of the fluids and also the height of the column above the bottom region. The pressure at the bottom of the test tube is calculated by multiplying the density of the fluids by the height of the column above the bottom. Here's how to calculate the pressure:
P = pgh
where P = Pressure, p = Density of fluid, g = Acceleration due to gravity, and h = Height of the column.
The pressure at the bottom of the test tube is the pressure which is exerted by the water and oil above it. The water is more dense than that of the oil, therefore it exerts more pressure on the bottom of the test tube. The pressure at the bottom of the test tube is given by the formula
The density of water is 1000 kg/m³, and the density of oil is 900 kg/m³. The height of the column of water is 6.5 cm, and the height of the column of oil is 2.5 cm.
Using the above formula: P = pgh
P (Water) = 1000 × 9.81 × 0.065
P (Water) = 641.65 Pa
P (Oil) = 900 × 9.81 × 0.025
P (Oil) = 220.725 Pa
Therefore, the pressure on the bottom of the tube is 641.65 Pa + 220.725 Pa = 862.375 Pa.
Learn more about Pressure here:
https://brainly.com/question/29672166
#SPJ11
Help asaaap it's about doppler effect
The frequency that the bad guy hear is 12000 hz when the police car is moving with speed of 80m/s.
Frequencyfo=fs(vvov), where fo is the observed frequency, fs is the source frequency, v is the speed of sound, vo is the observer's speed, the top sign indicates the observer is approaching the source, and the bottom sign indicates the observer is leaving the source.Equation fo=800(80-65) fo = 12000 after substituting the variablesThe apparent change in frequency of a wave as a result of an observer moving with respect to the wave source is known as the Doppler effect or Doppler shift. It bears the name of the Austrian physicist Christian Doppler, who first described the phenomenon in 1842.For more information on doppler effect kindly visit to
https://brainly.com/question/15318474
#SPJ1
What happens to the reaction rate when the concentration (absorbance) of the reactants is doubled? Determine the reaction order by solving the following equations. Show a sample computation in your lab notebook. rate; – [CV3]* = CV.x = x= _ rate4 _ [CV4]* Ox= ratez [CV]* rates _ [CVs]* rates CV.* rate, x=
The reaction rate will double when the concentration of the reactants is doubled. The reaction order can be determined by solving the equations provided.
For example, if the initial rate is given by:
Rate = [CV3]* = CV.x = x = rate4 [CV4]* Ox= ratez [CV]* rates [CVs]* rates CV.* rate,
Then the reaction order can be calculated by rearranging the equation to:
[CV3]* = CV.x/x = rate4 [CV4]* Ox/x = ratez [CV]* rates [CVs]* rates CV.* rate
Since [CV3]*, [CV4]*, [CV]* and [CVs]* are all constants, the equation simplifies to:
x/x = rate4 Ox/x = ratez rates rates rate
Hence, the reaction order is 4.
"reaction rate", https://brainly.com/question/31131380
#SPJ11
Given the definition of EER, find the EER of an 8000 Btu/hour air conditioner that requires a power input of 1500 W. Express your answer numerically in British thermal units per hour per watt. EER = __________(Btu/hour)/W
EER is defined as the Energy Efficiency Ratio which is the ratio of cooling capacity in BTU/hr to the power input in watts.
The EER of the given 8000 Btu/h air conditioner is 5.33 Btu/hour per watt.
In the case of the given 8000 Btu/h air conditioner that requires a power input of 1500 W, the EER can be calculated as follows:
EER = (cooling capacity in Btu/hr) / (power input in watts)
EER = 8000 Btu/hour / 1500 W = 5.33 Btu/hour per wat.
Energy efficiency ratio (EER) is used in the USA and is defined as the system output in Btu/h per watt of electrical energy.
Coefficient of performance (COP) is the equivalent measure using SI units, which is widely used in the UK. A COP of 1.0 equates to an EER of 3.4.
To know more about power:https://brainly.com/question/11569624
#SPJ11
A ball is thrown upwards and caught when it comes back down. In the presence of air resistance, the speed with which it is caught is:
(A) more than the speed it had when thrown upwards.
(B) the same as the speed it had when thrown upwards.
(C) less than the speed it had when thrown upwards.
A ball is thrown upwards and caught when it comes back down. In the presence of air resistance, the speed with which it is caught is C. less than the speed it had when thrown upwards.
When a ball is thrown upwards, it gains kinetic energy due to the force exerted by the thrower. Then, as it ascends, it loses kinetic energy and gains potential energy as it moves higher up. Finally, the ball comes to a stop, its kinetic energy becoming zero, and its potential energy reaches its maximum value. At the top, the ball begins to fall back to the ground.The air resistance opposes the motion of the ball, slowing it down as it travels upwards.
When the ball starts coming back down, the air resistance exerts an additional force, which slows down the ball and reduces its speed. As a result, the speed with which it is caught is less than the speed it had when thrown upwards. Hence, option (C) is correct.
Learn more about kinetic energy at:
https://brainly.com/question/22174271
#SPJ11
The capacity of a battery to deliver charge, and thus power, decreases with temperature. The same is not true of capacitors. For sure starts in cold weather, a truck has a 500 F capacitor alongside a battery. The capacitor is charged to the full 13.8 V of the truck's battery. How much energy does the capacitor store? What is the ratio between the energy density per unit mass of the 9.0 kg capacitor system and the 130,000 J/kg of the truck's battery.
The energy stored in the capacitor is calculated as 630150 J. The ratio between the energy density per unit mass of the 9.0 kg capacitor system and the 130,000 J/kg of the truck's battery is 70.17
The formula to calculate the energy stored in a capacitor is expressed by the formula:
E = (1/2)CV²
where E is energy, C is capacitance, and V is voltage.
The question mentions that the capacitor is fully charged to 13.8 V. Therefore, the energy stored in the capacitor is given by the formula:
[tex]E = (1/2)CV^2 \\= (1/2)\times (500 F)\times {(13.8 V)}^2\\= 630150 J[/tex]
The ratio between the energy density per unit mass of the 9.0 kg capacitor system and the 130,000 J/kg of the truck's battery can be computed by dividing the energy density of the capacitor system by the energy density of the truck's battery.
We know that energy density = energy / mass of the system.
Thus, the formula to calculate the ratio is:
[tex]Ratio = \dfrac{energy density per unit mass of capacitor system}{ energy density per unit mass of truck's battery}\\Ratio= \dfrac{630150 J / 9 kg}{ 130,000 J / 1 kg}= 70.017[/tex]
Therefore, the ratio of energy density per unit mass of the capacitor system to that of the truck's battery is 70.017.
To know more about capacitor, kindly click the below link:
https://brainly.com/question/29100869
#SPJ11
Which term describes the energy an object has due to the motion of its
particles?
A. Magnetic energy
B. Chemical energy
C. Elastic energy
D. Thermal energy
Answer: The answer is D. Thermal Energy.
Explanation:
Thermal energy is a type of kinetic energy owing to the fact that it results from the movement of particles.
a 35.0-g bullet moving at 475 m/s strikes a 4.4-kg bag of flour that is on ice, at rest. the bullet passes through the bag, leaving at 220 m/s. how fast is the bag moving when the bullet exits?
When the 35.0-g bullet moving at 475 m/s strikes the 4.4-kg bag of flour, the momentum of the bullet is transferred to the bag of flour, causing the bag of flour to move and the bag moving when the bullet exits at 91.3 m/s.
What is the speed of bag moving when the bullet exits?We can calculate the velocity of the bag of flour after the collision using conservation of momentum:
Here we have the following data as :
Momentum of bullet before collision = Momentum of bullet and bag after collision
m bullet × v bullet, before = (m bullet + m bag) bag × v bag, after
We can solve for v bag ,after:
v bag ,after = (m bullet × v bullet, before) / (m bullet + m bag)
v bag, after = (35.0 g × 475 m/s) / (35.0 g + 4.4 kg) = 91.3 m/s
Therefore, the bag of flour is moving at 91.3 m/s when the bullet exits.
Read more about mass here:
https://brainly.com/question/1838164
#SPJ11
what happens after the helium flash in the core of a star?
After the helium flash in a star, the core quickly heats up and expands.
A helium flash is the very brief thermal runaway nuclear fusion of significant amounts of helium into carbon during the red giant phase of low mass stars (between 0.8 solar masses (M) and 2.0 M). The centre expands as a result of the core becoming warmer as a result of this.
Following the onset of helium nuclear reactions in a star's core, helium nuclei fuse to create carbon and oxygen.
Most of the time, the stars' positions in reference to one another remain constant. Convergence between Orion and Taurus is ongoing. Ursa Minor is never far from Draco. The stars appear to us as an endless backdrop painting in the sky that hardly moves in reference to one another.
To know more about stars:
https://brainly.com/question/29572549
#SPJ4
We always see the same side of the Moon because a. the Moon does not rotate on its axis. b. the Moon rotates on its axis once for each revolution around Earth. c. when t…
We always see the same side of the Moon because
a. the Moon does not rotate on its axis.
b. the Moon rotates on its axis once for each revolution around Earth.
c. when the other side of the Moon is facing Earth, it is unlit.
d. when the other side of the Moon is facing Earth, it is on the opposite side of Earth.
e. none of the above
We always see the same side of the Moon because the "Moon rotates on its axis once for each revolution around Earth." Thus, the correct option will be B.
How does the Moon rotates?When the Moon rotates on its axis once for each revolution around Earth, then we always see the same side of the Moon. The reason behind this is that the moon's rotation takes almost the same time as it takes to orbit the Earth.
When the same side of the moon is facing the Earth, it appears to be unchanging. That is why we always see the same side of the moon from Earth. The other side of the Moon is known as the far side, which was first observed by the Soviet spacecraft Luna 3 in 1959.
Therefore, the correct option will be B.
Learn more about Moon here:
https://brainly.com/question/13538936
#SPJ11
