Answer:
The answer is below
Explanation:
Both a gage and a manometer are attached to a gas tank to measure its pressure. If the reading on the pressure gage is 65 kPa, determine the distance between the two fluid levels of the manometer if the fluid is a) mercury b) water
Solution:
A manometer is a device used to measure pressure. A manometer is made up of a U shaped tube containing liquid. The difference of pressure in the two arms causes the liquid to reach different heights.
a) The density of mercury ([tex]\rho_{Hg}[/tex]) = 13600 kg/m³, Pressure (P) = 65 kPa and g = 9.8 m/s², h = distance between the two fluid levels
[tex]P=\rho_{Hg}*g*h\\\\h=\frac{P}{\rho_{Hg}*g} =\frac{65*10^3\ Pa}{13600*9.81}=0.487\ m[/tex]
b) For water, [tex]\rho_w[/tex] = 1000 kg/m³, hence:
[tex]P=\rho_{w}*g*h\\\\h=\frac{P}{\rho_{w}*g} =\frac{65*10^3\ Pa}{1000*9.81}=6.6\ m[/tex]
For automobile engines, identify the best choice of motor oil.
A. High viscosity for Maine in the winter and low viscosity for Florida in the summer.
B. Low viscosity for Maine in the winter and low viscosity for Florida in the summer.
C. Low viscosity for Maine in the winter and high viscosity for Florida in the summer.
D. High viscosity for Maine in the winter and high viscosity for Florida in the summer.
E. It does not matter what the rating is for the motor oil.
Answer:
C. Low viscosity for Maine in the winter and high viscosity for Florida in the summer.
Explanation:
The choice of motor oil or engine oil depends on the type of engine and also on the type of climate on which the engine runs.
In winter climates, we should use oil with low viscosity as at lower temperatures, the it flows more readily if its viscosity is low.
But the summer season needs a relatively thicker oil so as to reduce the thinning effect of the oil out of the engine.
Thus for Maine in the winter season, we need a low viscosity oil and for Florida a high viscosity oil in the summer season.
Therefore, option (c) is correct.
what is the difference between a series circuit and a parallel circuit?
Answer:
In a parallel circuit, the voltage across each of the components is the same, and the total current is the sum of the currents flowing through each component. ... In a series circuit, every device must function for the circuit to be complete. If one bulb burns out in a series circuit, the entire circuit is broken.
Explanation:
1.1.2
Energy
1.1.3
Mass
1.1.4
Temperature
Power
1.1.5
1.2 State Ohm's law
1.3 State Joule's law
1.5 Name four factors that9 determine the resistance of the material
1.6 What is the SI Unit for current?
QUESTION 2
Answer:
the energy is sgdrh35679
"All data types are keywords but all keywords are not data types", justify this statement.
Keywords Are Reserved Words Which Are Not Use As Normal Cases But Used For Special Purpose In Our Program whereas, Data Type Tells The Compiler And Interpreter How The Program Is Going To Be Executed And Can Be Used At Every Cases.
Hope This Helps You ❤️Based on how they are stored in the computer, the types produced by these keywords can be categorized into two families, integer types and floating-point types.
What is the relation between data and keyword?Bit, byte, and word are terminology that can be used to refer to either memory or data storage units in computers.
The main distinction between text fields and keyword fields is that text fields are examined during indexing, whereas keyword fields are not.
This means that while keyword fields are indexed exactly as is, text fields are split down into their constituent phrases at indexing to allow for partial matching.
A word or collection of words that an Internet user enters into a search engine or search bar to conduct a search is referred to as a keyword in the context of digital marketing.
Therefore, All data types are keywords, but all keywords are not data types.
Learn more about data and keywords here:
https://brainly.com/question/9588905
#SPJ2
A projectile is fired horizontally with an initial speed of 50.0 m/s. Neglect air resistance.a) What is the magnitude of the displacement of the projectile 3.00 s after it is fired?b) What is the speed of the projectile 3.00 s after it is fired?c) What is the magnitude of the acceleration of the projectile 3.00 s after it is fired?
Answer:
a) 156 meters
b) 58 m/s
c) 9.8 m/s^2
Explanation:
a) The horizontal displacement X = V *t
X = 50 * 3 = 150 meters
Vertical displacement = y = – g * t² / 2
Y = -9.8 *3*3/2 = -4.9*9 = 44.1
Net Displacement = Sqrt (X^2 +Y^2) = 156.34 = 156 meters
b) Speed of the projectile
vx = 50 m/s
vy = t*g = 9.8*3 = 29.4
V = Sqrt (vx^2 + vy^2) = 58 m/s
c) Acceleration is the acceleration due to gravity = 9.8 m/s^2
The magnitude of the displacement of the projectile is equal to 156 meters.
Given the following data:
Initial speed = 50.0 m/s. Time = 3.00 seconds.Scientific data:
Acceleration due to gravity (g) = [tex]9.8 m/s^2.[/tex]How to calculate the displacement.Mathematically, the magnitude of the displacement of a projectile is given by this formula:
[tex]Horizontal\;displacement = Vt\\\\Horizontal\;displacement = 50.0 \times 3.00[/tex]
Horizontal displacement = 150.0 meters.
[tex]Vertical displacement =\frac{1}{2} gt^2\\\\Vertical displacement =\frac{1}{2} \times 9.8 \times 3^2\\\\Vertical displacement =\frac{1}{2} \times 9.8 \times 9[/tex]
Vertical displacement = 44.1 meters.
[tex]D^2 = X^2 +Y^2\\\\D =\sqrt{44.1^2+150^2}[/tex]
D = 156.34 ≈ 156 meters.
b. For the speed of the projectile:
Vertical speed = tg
[tex]V_y = tg = 9.8\times3\\\\ V_y = 29.4\;m/s[/tex]
[tex]D^2 = V_x^2 +V_y^2\\\\D =\sqrt{50^2+29.4^2}[/tex]
D = 58 m/s.
c) The magnitude of the acceleration of the projectile is equal to the acceleration due to gravity ([tex]9.8 \;m/s^2[/tex]).
Read more on acceleration here: brainly.com/question/247283
SN1 reactions usually proceed with ________. A) equal amounts of inversion and retention at the center undergoing substitution B) slightly more inversion than retention at the center undergoing substitution C) slightly more retention then inversion at the center undergoing substitution D) complete inversion at the center undergoing substitution E) complete retention at the center undergoing substitution complete retention at the center undergoing substitution slightly more retention then inversion at the center undergoing substitution complete inversion at the center undergoing substitution equal amounts of inversion and retention at the center undergoing substitution slightly more inversion than retention at the center undergoing substitution
Answer:
equal amounts of inversion and retention at the center undergoing substitution
Explanation:
In an SN1 reaction, the rate determining step is the formation of a carbonation which is flat and planar.
This means that both faces of the carbo cation are equally available for attack by the nucleophile.
Attack on either of the faces may occur equally thereby yielding a racemic mixture.
Your new team is working hard, but they are all less experienced than you and don't complete their tasks as quickly.What would you be most and least likely to do? (A). Reach out to your manager to discuss the situation.Try to identify the best way to support the new associates. (B).Remind your coworkers of performance expectations and that they need to be working harder to complete tasks. (C). Offer to help others complete their tasks; observe their work process and provide some tips that might help them. (D). Give your coworkers more time to figure out how to do the task; they likely just need more practice with what they've already learned.