Answer:
The emf of a cell is the sum of the electric potential differences (PDs) produced by a separation of charges (electrons or ions) that can occur at each phase boundary (or interface) in the cell. The magnitude of each PD depends on the chemical nature of the two contacting phases.
Explanation:
pls mark brainliest
which is part of the convection cycle in earths atmosphere?
a. hot, denser air rises
b. cold, denser air rises
c. hot, less-dense air rises
d. cold, less-dense air falls
Answer pls. This is for People like me with this Question . Help!!! Question 3 of 20 What happens to the electric force between two particles if the distance between them is reduced by half? O A. It decreases to half the original force. OB. It increases to twice the original force. O C. It increases to 4 times the original force. O D. It decreases to 1/4 of the original force.
Answer:
It increases twice the original
A frictionless pulley used to lift 8000N of concrete. What is the minimum effort required to raise the block
Answer: 8000N
Explanation: since it is frictionless that means it has 100% efficiency therefore the mechanical advantage is 1 meaning the load equals to the effort
Can someone help me with this Physics question please?
Q. The half-life of tritium (hydrogen-3) is 12.3 years. If 48.0mg of tritium is released from a nuclear power plant during the course of a mishap, what mass of the sample will remain after 49.2 years?
Answer:
Explanation:
The formula for this, the easy one, is
[tex]N=N_0(\frac{1}{2})^{\frac{t}{H}[/tex] where No is the initial amount of the element, t is the time in years, and H is the half life. Filling in:
[tex]N=48.0(\frac{1}{2})^{\frac{49.2}{12.3}[/tex] and simplifying a bit:
[tex]N=48.0(.5)^4[/tex] and
N = 48.0(.0625) so
N = 3 mg left after 12.3 years
How many half-lifes is 49.2 years ?
(49.2 years) / (12.3 years per half-life) = 4 half-lifes.
In 4 half-lifes, (1/2) · (1/2) · (1/2) · (1/2) of the original sample remains.
That's (1/2⁴) or (1/16) of the original.
(1/16) of 48.0 mg = 3 mg .
=======================
Step-by-step:
== Start with 48 mg .
== After one half-life, 24 mg remains.
== Then, after the second half-life, 12 mg remains.
== Then, after the third half-life, 6 mg remains.
== Then, after the fourth half-life, 3 mg remains.
Why is a flower not a good blackbody radiator?
Answer:
A flower emits only visible light
A flower reflects much of the light that hits it
write the relation of m² with its a multiple
Explanation:
The square meter is the SI-derived unit of area. It has a symbol m² (33A1 in Unicode). It is defined as the area of a square whose sides measure exactly one metre.
Convertir 25 km/h a m/s
Answer:
6.9 m/s
Explanation:
1000m = 1km
3600s = 1hr
25000m/3600s
6.9m/s
Different nutrients play different roles in our bodies. Which is the energy-storing nutrient?
O carbohydrates
O minerals
O proteins
O fats
Answer:
D. Fats
Explanation:
they are the long term energy storing nutrient carbohydrates are a quick way for energy minerals dont contain any energy and neither do proteins
fats
Explanation:
it is nutrient kept in the body
Cuánto demorará un cuerpo en alcanzar su máxima altura, sabiendo que fue lanzado, verticalmente hacia arriba, con una velocidad cuyo valor fue de 90 m/s?
Answer:
The maximum height reached is 413.27 m.
Explanation:
How long will it take for a body to reach its maximum height, knowing that it was thrown, vertically upwards, with a velocity whose value was 90 m / s?
initial velocity , u = 90 m/s
gravity, g = 9.8 m/s^2
Let the maximum height is h.
At maximum height the velocity v = 0
Use third equation of motion
[tex]v^2 = u^2 - 2 gh\\\\0 = 90\times 90 - 2 \times 9.8 \times h\\\\h = 413.27 m[/tex]
The engine starter and a headlight of a car are connected in parallel to the 12.0-V car battery. In this situation, the headlight operates at 38 W and the engine starter operates at 2.40 kW. If the headlight and starter were then rewired to be in series with each other, what total power would they consume when connected to the 12.0-V battery
Answer:
The total power they will consume in series is approximately 2.257 W
Explanation:
The connection arrangement of the headlight and the engine starter = Parallel to the battery
The voltage of the battery, V = 12.0 V
The power at which the headlight operates in parallel, [tex]P_{headlight}[/tex] = 38 W
The power at which the kick starter operates in parallel, [tex]P_{kick \ starter}[/tex] = 2.40 kW
We have;
P = V²/R
Where;
R = The resistance
V = The voltage = 12 V (The voltage is the same in parallel circuit)
For the headlight, we have;
R₁ = V²/[tex]P_{headlight}[/tex] = 12²/38 = 72/19
R₁ = 72/19 Ω
For the kick starter, we have;
R₂ = V²/[tex]P_{kick \ starter}[/tex] = 12²/2.4 = 60
R₂ = 60 Ω
When the headlight and kick starter are rewired to be in series, we have;
Total resistance, R = R₁ + R₂
Therefore;
R = ((72/19) + 60) Ω = (1212/19) Ω
The current flowing, I = V/R
∴ I = 12 V/(1212/19) Ω = (19/101) A
We note that power, P = I²R
In the series connection, we have;
[tex]P_{headlight}[/tex] = I² × R₁
∴ [tex]P_{headlight}[/tex] = ((19/101) A)² × 72/19 Ω = 1368/10201 W ≈ 0.134 W
The power at which the headlight operates in series, [tex]P_{headlight, S}[/tex] ≈ 0.134 W
[tex]P_{kick \ starter}[/tex] = ((19/101) A)² × 60 Ω = 21660/10201 W ≈ 2.123 W
The power at which the kick starter operates in series, [tex]P_{kick \ starter, S}[/tex] ≈ 2.123 W
The total power they will consume, [tex]P_{Total}[/tex] = [tex]P_{headlight, S}[/tex] + [tex]P_{kick \ starter, S}[/tex]
Therefore;
[tex]P_{Total}[/tex] ≈ 0.134 W + 2.123 W = 2.257 W
which best describes how air moves during convection?
a. cool air warms as it mixes with denser air
b. warm air cools as it mixes with cooler, denser air
c. warm air is displaced by cooler denser air
a. cool air warms as it mixes with denser air
Explanation:
c. warm air is displaced by cooler denser air
rjeheheuwyeydyevevevrvdvev4hdj374gdddfeh4uarjtsk5sk5ek6eel5os5je5ie663i63iw64niw4h8
what is the source of energy
A 25.0 kg probe fell freely with acceleration of 2.00 m/s^2 just before it landed on a distant planet. What is the weight of the space probe on that planet
Answer:
The weight of the probe is 50 Newtons
Explanation:
Newtons second law states that F = ma
Given the mass of 25kg, and the acceleration of 2m/s^2, we can substitute both values into the equation to find the weight force.
[tex]F = ma[/tex]
[tex]F = 25 * 2[/tex]
[tex]F = 50N[/tex]
The weight of the probe is 50 Newtons
Is a nanoliter greater then one liter?
Which wave has the smallest amplitude?
Answer:
C. C
Explanation:
A wave can be defined as a disturbance in a medium that progressively transports energy from a source location to another location without the transportation of matter.
In Science, there are two (2) types of wave and these include;
I. Electromagnetic waves: it doesn't require a medium for its propagation and as such can travel through an empty space or vacuum. An example of an electromagnetic wave is light.
II. Mechanical waves: it requires a medium for its propagation and as such can't travel through an empty space or vacuum. An example of a mechanical wave is sound.
A crest can be defined as the highest (vertically) point on a waveform.
On a related note, a trough is the lowest (vertically) on a waveform.
An amplitude can be defined as a waveform that's measured from the center line (its origin or equilibrium position) to the bottom of a trough or top of a crest. Thus, the vertical axis (y-axis) is the amplitude of a waveform i.e it's measured vertically.
In this scenario, waveform C which is represented by a blue curvy line has the smallest amplitude in comparison with the other waveforms because it has the minimum height when measured from the origin.
In contrast, waveform A represented by a purple line has the highest amplitude because it has the maximum height when measured from the origin.
Mathematically, the amplitude of a wave is given by the formula;
x = Asin(ωt + ϕ)
Where;
x is displacement of the wave measured in meters.A is the amplitude.ω is the angular frequency measured in rad/s.t is the time period measured in seconds.ϕ is the phase angle.Answer:
The answer is indeed D as the comment above suggests.
Explanation:
Simply put, wave D's highest point is closer to the line than all of the other high points of A, B and C
what is the power of ideal sunglass
URGENT
A river flows toward 90°. Mark, a riverboat
pilot, heads the boat at 297º and is able to go
straight across the river at 6.0 m/s.
a. What is the velocity of the current?
b. What is the velocity of the boat as seen
from the river bank?
tại sao trái đất lại có trọng lực
Answer:
wew uhh uhh uhh uhh haha btw thanks po sa points pa brainliest po please po
Firing a small rocket that starts at rest, the VMS-2 rises vertically under uniform acceleration, and in 50 seconds all the fuel is burned out. What is the maximum height at which the rocket rises?
An ice-skater with a mass of 80kg is holding a bowling ball with a mass of 8 kg. Suppose that the skater tosses the bowling ball forward with a speed of 6 m/s. What is the skater's reactive velocity? Show all work.
Answer:
0.6 m/s
Explanation:
The details of the masses and velocities are;
The mass of the ice skater, m₁ = 80 kg
The mass of the ball, m₂ = 8 kg
The speed with which the skater tosses the ball forward, v₂ = 6 m/s
Therefore;
According to the principle of conservation of linear momentum, we have;
m₁·v₁ = m₂·v₂
Where;
v₁ = The skater's reactive velocity
Therefore, we get;
80 kg × v₁ = 8 kg × 6 m/s
v₁ = 8 kg × 6 m/s/(80 kg) = 0.6 m/s
The skater's reactive velocity, v₁ = 0.6 m/s.
What uses non-renewable energy?
A)a gematrical heating system
B)a nuclear power station
C)a solar panel
D)a wind turbine
Uma pilha AA (pilha de controle remoto) fornece ao circuito 1,5V, já uma bateria de carro fornece 12V. Qual a relação entre a energia fornecida entre esses elementos de circuito?
Answer:
The ratio of energy of AA battery to the car battery is 0.0156.
Explanation:
An AA battery (remote control battery) supplies the circuit with 1.5V, while a car battery supplies 12V. What is the relationship between the energy supplied between these circuit elements?
Supply by AA battery = 1.5 V
Supply by car battery = 12 V
The resistance of the circuit is R.
The energy supplied = V^2/R
The energy supplied by the AA battery is
E = 1.5 x 1.5 / R = 2.25/R
The energy supplied by the car battery is
E' = 12 x 12/ R = 144 / R
So, the ratio of
E : E' = 2.25 : 144 = 0.0156
What conditions can impact the ecological tolerance of a species?
Pls Answer,30 points
Answer:
climatic changes
ambient changes
human interferance and the growt of cities and human civilization
and invasive especies
Explanation:
Many different physical factors can impact the ecological tolerance of a species like:-
temperature humidity soil chemistry pHsalinity oxygen levelsHow physical factors impact the ecological tolerance of a species?Climatic factors such as temperature and precipitation are key drivers to control species distribution directly.Topographic features such as slope and elevation can impact local climate as well as soil conditions that in turn have varied effects on vegetation structure.The relative distance from a water source can also affect the composition and distribution of woody vegetation because of the resulting varying amount of water available for growth. Physical and chemical soil properties can inform vegetation patterns on a local scale.What is a tolerance range?The portion of the abiotic factor's range of variation which a species can survive and function in is commonly defined as the tolerance range.
To know more about ecological tolerance here
https://brainly.com/question/26471341
#SPJ2
Which wave has the largest amplitude?
A.D
B.B
C.C
D.A
Answer:
D. A
General Formulas and Concepts:
Simple Harmonic Motion
Parts of a wave
PeriodAmplitudeWavelengthCrest/TroughExplanation:
The amplitude is the distance from the horizon to either the crest or trough of a wave.
In layman's terms, it is how high the wave is.
The "highest" wave would be wave A.
∴ our answer is D.
Topic: AP Physics 1 Algebra-Based
Unit: SMH
Answer:
A (The wave)
Explanation:
Wave A
You are trying to hold your 550 g physics books with your hand against a vertical wall. Using a force sensor you know that the force you are applying is 10.0 N. Below the book on the floor you have placed a motion sensor. The position time graph for the book is given. Find the coefficient of kinetic friction.
The book's position is changing linearly with time, so its velocity is constant. This means that the net force acting on the book in the direction parallel to the surface is
∑ F = 10.0 N - n = 0
where n is the magnitude of the normal force on the book due to the wall, and the net force perpedicular to the surface is
∑ F = f - (0.550 kg) g = 0
where f is the mag. of kinetic friction, and f = µn where µ is the coefficient of kinetic friction.
Then
• n = 10.0 N
• f = (0.550 kg) g = 5.39 N
• 5.39 N = µ (10.0 N)
==> µ = 0.539
Answer:
Above answer
Explanation:
The book's position is changing linearly with time, so its velocity is constant. This means that the net force acting on the book in the direction parallel to the surface is
∑ F = 10.0 N - n = 0
where n is the magnitude of the normal force on the book due to the wall, and the net force perpedicular to the surface is
∑ F = f - (0.550 kg) g = 0
where f is the mag. of kinetic friction, and f = µn where µ is the coefficient of kinetic friction.
Then
• n = 10.0 N
• f = (0.550 kg) g = 5.39 N
• 5.39 N = µ (10.0 N)
==> µ = 0.539
Which symbol and unit of measurement are used for electric current?
symbol. A, unit: 1
symbol: C, unit: A
symbol l; unit C
symbol: 1; unitA
Answer: Symbol is I and unit A
Explanation: A represents Amperes
HOPE THIS HELPS!!!!!!!!
A stone is thrown vertically upwards with an initial velocity of 20m/sec. Find the maximum height ot reaches and the time taken by it to reach the height. (g=10m/s2)
plz short numerical ASAP
Answer:
The height reached is 20m, The time taken to reach 20m is 2 seconds
Explanation:
Observing the equations of motion we can see that the following equation will be most helpful for this question.
[tex]v^{2} = u^{2} + 2as[/tex]
We are given initial velocity, u
We know that the stone will stop at its maximum height, so final velocity, v
Acceleration, a
And we are looking for the displacement (height reached), s
Substitute the values we are given into the equation
[tex]0^{2} = 20^{2} + 2(10)s[/tex]
Rearrange for s
[tex]0^{2} -20^{2} =20s[/tex]
[tex]-400=20s[/tex]
[tex]\frac{-400}{20} =s[/tex]
s = -20 (The negative is just showing direction, it can be ignored for now)
The height reached is 20m
Use a different equation to find the time taken
[tex]s = vt - \frac{1}{2} at^{2}[/tex]
Substitute in the values we have
[tex]-20=(0)t - \frac{1}{2} (10)t^{2}[/tex]
Rearrange for t
[tex]-20 =0 -5 t^{2}[/tex]
[tex]\frac{-20}{-5} =t^{2}[/tex]
[tex]4 = t^{2}[/tex]
t = 2s
The time taken to reach 20m is 2 seconds
the internal resistance of each of the following cells E1 and E2 shown in the figure above is 2ohms. calculate the total current in the circuit
Answer:
The total current in the circuit is 0.8 A.
Explanation:
internal resistance of each battery = 2 ohm
Total emf of the circuit, E = E1 + E2 = 2 = 2 = 4 V
Now total internal resistance is
[tex]r = \frac{2\times 2}{2 + 2}= 1 ohm[/tex]
Total resistance, R = 4 = 1 = 5 ohm
Let the current is I.
E = I R
4 = I x 5
I = 0.8 A
please answer me my question
the direction of applied force has to be_____ to the distance in order to say work is done
Answer:
Explanation:
The direction of the applied force has to be parallel to the distance an object moved in order to say that work has been done.
