Các đặc điểm chính của đường dây dài siêu cao áp .

Answer:

ay man ima be real, i just need the points yo

78950W the answer

Explanation:

A 75- kw, 3-, Y- connected, 50-Hz 440- V cylindrical synchronous motor operates at rated condition with 0.8 p.f leading. the motor efficiency excluding field and stator losses, is 95%and X=2.5ohms. calculate the mechanical power developed, the Armature current, back e.m.f, power angle and maximum or pull out torque of the motor

A 75- kw, 3-, Y- connected, 50-Hz 440- V cylindrical synchronous motor operates at rated condition with 0.8 p.f leading. the motor efficiency excluding field and stator losses, is 95%and X=2.5ohms. calculate the mechanical power developed, the Armature current, back e.m.f, power angle and maximum or pull out torque of the motor

Answer: hello some data related to your question is missing attached below is the missing data

answer:

T2 = 265°C

Explanation:

First step : calculate sum of vertical forces

∑ y = 0

Fmg - 2(0.5 Fst ) = 0

∴Fmg = ( 12 * 10^6 ) ( 2 * π/4 (0.01)^2 )

          = 1884.96 N

Also determine the Compatibility equation in order to determine the change in Temperature

ΔT = 250°C

therefore Temperature at which average normal stress becomes 12.0 MPa

ΔT = T2 - T1

250°C = T2 - 15°C

T2 = 250 + 15 = 265°C

attached below is the detailed solution

Answer:

0.2063

Explanation:

Given data:

packing factor = 0.5

percentage of reduction of powders = 70%

Calculate the final porosity

after sintering Bulk specific volume = 0.9 * 0.7 = 0.63

assuming true specific volume = 1

packing factor = 0.5 , bulk specific volume = 2

packing factor after pressing and sintering

= 1 / ( 2 * 0.63 ) = 0.7937

hence : porosity = 1 - packing factor

                            = 1 - 0.7937 = 0.2063

Answer:

Answer:

1 NAND gate

Explanation:

The minimum number of 2 input NAND gates that can be used to implement the combinational circuit = 1

The only true combinations conditions that can produce a false result ( i.e. condition/result different from the expected result as stated in the question )

Sensor 2 activated + Emergency switch pressed = False ( Line will keep moving )

Answer:

1.2727 stokes

Explanation:

specific gravity of fluid A = 1.65

Dynamic viscosity = 210 centipoise

Calculate the kinematic viscosity of Fluid A

First step : determine the density of fluid A

Pa = Pw * Specific gravity =  1000 * 1.65 = 1650 kg/m^3

next : convert dynamic viscosity to kg/m-s

210 centipoise = 0.21 kg/m-s

Kinetic viscosity of Fluid A = dynamic viscosity / density of fluid A

                                            = 0.21 / 1650 = 1.2727 * 10^-4 m^2/sec

Convert to stokes = 1.2727 stokes

Answer:

Option C = Only 1 path for current to flow.

Answer:

The volume for this is 29.7

Explanation:

Trust me on this I'm an expert

Answer:

a. 6.6 Mpsi

b. 5.64 Mpsi

c. i. 0.095  ii. -0.095

Explanation:

a. The true stress in tension is:

The true stress in tension, σ = σ'(1 + ε) where σ' = engineering stress in tension = 6 Mpsi and ε = engineering strain under tension = (L₁ - L₀)/L₀ where L₀ = gage length = 2 inches and L₁ = length at elongation under tension = 2.2 inches. So,  ε = (L₁ - L₀)/L₀ = (2.2 - 2)/2 = 0.2/2 = 0.1

So, σ = σ'(1 + ε)

σ = 6 Mpsi(1 + 0.1)

σ = 6 Mpsi(1.1)

σ = 6.6 Mpsi

b. The true stress in compression is:

The true stress in tension, σ₁ = σ"(1 + ε) where σ' = engineering stress in tension = 6 Mpsi and ε' = engineering strain under tension = (L₂ - L₀)/L₀ where L₀ = gage length = 2 inches and L₂ = length at elongation under compression = 1.818 inches. So,  ε' = (L₂ - L₀)/L₀ = (1.818 - 2)/2 = -0.182/2 = -0.091

So, σ₁ = σ'(1 + ε')

σ₁ = 6.2 Mpsi[1 + (-0.091)]

σ₁ = 6.2 Mpsi[1 - 0.091)

σ₁ = 6.2 Mpsi(0.909)

σ₁ = 5.64 Mpsi

c. The true strains in both tension and compression are :

i. The true strain in tension

The true strain in tension ε" = ㏑(1 + ε) where ε = engineering strain in tension = 0.1

So, ε" = ㏑(1 + ε)

ε" = ㏑(1 + 0.1)

ε" = ㏑(1.1)

ε" = 0.095

ii. The true strain in compression

The true strain in tension ε₁ = ㏑(1 + ε') where 'ε = engineering strain in compression = -0.091

So, ε₁ = ㏑(1 + ε')

ε₁ = ㏑[1 + (-0.091)]

ε₁ = ㏑(1 - 0.091)

ε₁ = ㏑(0.909)

ε₁ = -0.095

Answer:

60000 H

Explanation:

We are given;

Number of turns; N = 3000 turns

Change in flux = 900 - 860 = 40 Wb

Change in current = 9 - 7 = 2 A

Now, the formula for incremental inductance is given as:

L = N(Change in flux/Change in current) where;

N is Number of turns

Plugging in the relevant values, we have;

L = 3000(40/2)

L = 60000 H.

Answer: hello attached below is the question properly written

a) 2670 Kw

b) product will be made up of vapor and liquid

c) Product will be a super cooled liquid

Explanation:

mass Flow rate ( m ) = 175 kg/min

pressure = 1 atm

molecular weight of ethylene glycol ( mw ) = 62.07 g/mol

enthalpy of vaporization ( ΔHv ) = 56.9 KJ/mol

Using values from the table 8.1 related to the question

a) Determine the rate at which heat must be transferred from condenser

Using values from the table 8.1 related to the question

ΔH = 2670 Kw

b) If heat is transferred  at a lower temperature the product will be made up of vapor and liquid

c) If heat was transferred at a higher temperature the product will be a super cooled liquid

False, Good housekeeping eliminates accident and fire hazards. It also maintains safe, healthy work conditions; saves time, money, materials, space, and effort; improves productivity and quality; boosts morale; and reflects an image of a well-run, successful organization.

Hope it helps you❤️

Explanation:

sory sorry sorry sorrysorrysorry

Answer:

The view factor for radiation emitted by surface 2 to surface 1 is 0.1

Explanation:

Given

[tex]F_{12} = 0.4[/tex]

[tex]A_1 = 0.01m^2[/tex]

[tex]A_2 = 0.04m^2[/tex]

Required

Determine [tex]F_{21}[/tex]

To do this, we make use of the following equivalent ratio

[tex]A_1 * F_{12} = A_2 * F_{21}[/tex]

Make [tex]F_{21[/tex] the subject

[tex]F_{21} = \frac{A_1 * F_{12}}{ A_2}[/tex]

Substitute values into the equation

[tex]F_{21} = \frac{0.01m^2 * 0.4}{0.04m^2}[/tex]

[tex]F_{21} = \frac{0.01 * 0.4}{0.04}[/tex]

[tex]F_{21} = \frac{0.004}{0.04}[/tex]

[tex]F_{21} = 0.1[/tex]

Answer:

In the clevis shown in Fig. 1-11b, find the minimum bolt diameter and the minimum thickness of each yoke that will support a load P = 14 kips without exceeding a shearing stress of 12 ksi and a bearing stress of 20 ksi.

127-clevis-double-shear-bolt.gif

Solution 127

Hide Click here to show or hide the solution

127-fbd-clevis-double-shear-bolt.gifFor shearing of rivets (double shear)

P=τA

14=12[2(14πd2)]

d=0.8618in → diameter of bolt answer

For bearing of yoke:

P=σbAb

14=20[2(0.8618t)]

t=0.4061in → thickness of yoke answer

Answer:

Answer to the following is as follows;

Explanation:

A request for proposal is a documentation that invites prospective contractors to submit business opportunities to an agency or corporation interested in procuring a commodities, product, or valuable resource through a bid procedure.

A request for proposal (RFP) is a commercial document that introduces a project, defines it, and invites eligible contractors to compete on its completion.

Answer:

The type of succession is:

Primary succession

Explanation:

This is a type of succession that occurs after a volcanic eruption or earthquake; it involves the breakdown of rocks by lichens to create new, nutrient rich soils.

Primary succession is one of the two types of succession we have. It begins on rock formations, such as volcanoes or mountains, or in a place with no organisms or soil.

Answer:

bood ekogcd gcaerh is an American fbnuxc

Answer:

a. True

b. False

Explanation:

a. Since true stress, σ' = σ(1 + ε) where σ = engineering stress and ε = engineering strain.

Also under tension ε > 0, so, (1 + ε) > 1

Since (1 + ε) = σ'/σ > 1, ⇒ σ' > σ

So, the true stress is greater than the engineering stress.

So, the statement is true

b. Creep is a time-dependent deformation under certain applied load.

Creep occurs at high temperatures under different types of stress.

But, Creep test is carried out at constant high temperature and constant stress.

This statement is false.

Answer:

Calcium Chloride

Brine Wash

Drierite

Explanation:

Removal of small amounts of water from a polar solvent is Calcium Chloride

Removal of visible pockets of water from an organic solvent is Brine Wash

Storage of solvents or other materials in a desiccator is Drierite

Answer:

here you go.

screenshot 2 should give you some basic idea

Answer:

Following are the program to the given question:

def calculate_storage(filesize):#definging a method calculate_storage that takes filesize as a parameter  

 block_size = 4096#definging block_size that holds value

 full_blocks = filesize//block_size#definging full_blocks that divides the value and hold integer part

 partial_block_remainder = filesize%block_size#definging partial_block_remainder that holds remainder value

 if partial_block_remainder > 0:#definging if that compare the value

   return block_size*full_blocks+block_size#return value

 return block_size*full_blocks#return value

print(calculate_storage(1))    # calling method by passing value

print(calculate_storage(4096)) # calling method by passing value

print(calculate_storage(4097)) # calling method by passing value

Output:

4096

4096

8192

Explanation:

In this code, a method "calculate_storage" is declared that holds a value "filesize" in its parameters, inside the method "block_size" is declared that holds an integer value, and defines "full_blocks and partial_block_remainder" variable that holds the quotient and remainder value and use it to check its value and return its calculated value. Outside the method, three print method is declared that calls the method and prints its return value.

Solution :

For R-134a, we are given :

[tex]$T_i = 25^\circ C$[/tex]

[tex]$P_i=750 \ kPa$[/tex]

[tex]$P_e=165 \ kPa$[/tex]

Now we have one inlet and one exit flow, no work and no heat transfer. The energy equation is :

[tex]$h_e+\frac{1}{2}.v_e^2= h_i+\frac{1}{2}.v_i^2 $[/tex]

We also know that the gas is throttled and there is no change in the kinetic energy.

So, [tex]$v_e=v_i$[/tex]

Now from the energy equation above, we can see that the inlet and the exit enthalpies are also the same. Therefore,

[tex]$h_i=h_e$[/tex]

From the saturated R-134a table, corresponding to [tex]P_e = 165 \ kPa[/tex], we can find the exit saturation temperature.

[tex]$T_e=-15^\circ C$[/tex]

From the saturated R-134a table, corresponding to [tex]P_e = 165 \ kPa[/tex], we can find the specific enthalpies :

[tex]$h_f = 180.19 \ kJ/kg$[/tex]

[tex]$h_{fg} = 209 \ kJ/kg$[/tex]

Calculating the exit flow quality factor,

[tex]$x_e=\frac{h_e-h_f}{h_{fg}}$[/tex]

    [tex]$=\frac{234.59-180.19}{209}$[/tex]

   = 0.26

From the saturated R-134a table, corresponding to [tex]P_e = 165 \ kPa[/tex], we can find the specific volumes :

[tex]$v_f = 0.00746 \ m^3/kg$[/tex]

[tex]$v_{fg} = 0.11932 \ m^3/kg$[/tex]

Calculating the exit specific volume :

[tex]$v_e=v_f+x_e(v_{fg})$[/tex]

   = 0.000746 + 0.26 (0.11932)

   = 0.0318 [tex]m^3/kg[/tex]

The mass flow is equal to :

[tex]$\dot{m} = A_i . \frac{v}{v_i}$[/tex]

  [tex]$=A_e . \frac{v}{v_e}$[/tex]

So, [tex]$\frac{A_e}{A_i}=\frac{v_e}{v_i}$[/tex]

Therefore, the ratio of the exit pipe and the inlet pipe diameter is equal to

[tex]$\frac{D_e}{D_i}=\sqrt{\frac{A_e}{A_i}}$[/tex]

[tex]$\frac{D_e}{D_i}=\sqrt{\frac{v_e}{v_i}}$[/tex]

[tex]$\frac{D_e}{D_i}=\sqrt{\frac{0.0318}{0.000829}}$[/tex]

[tex]$\frac{D_e}{D_i}=6.19$[/tex]

Answer:

Minimum city gas mileage is 15

Explanation:

Minimum city gas mileage among 13 different car sizes in 2008 is 15.

Answer:

The answer is below

Explanation:

a) The work done is equal to the loss in kinetic energy (KE)

Change in kinetic energy (ΔKE) = Final kinetic energy - initial kinetic energy

Final KE = [tex]\frac{1}{2}mv_f^2[/tex]

But the final velocity is 0 (at rest). Hence:

Final KE = [tex]\frac{1}{2}mv_f^2=\frac{1}{2}m(0)^2=0[/tex]

ΔKE = 0 - K = -K

W = ΔKE = -K

Also, the work done (W) = charge (q) * distance (d) * electric field intensity (E)

W = qEd

but q = -e, hence:

W = -e * E * d

Using:

W = ΔKE

-e * E * d = -K

E= K / (e * d)

b) The electric field is in the direction of the electrons motion

Answer:

a) 4-input XOR, input data-1001  = 0 Even parity Bit

b)  5-input XOR, input data-10010 = 0 Even parity Bit  

c) 6-input XOR, input data-101001 = 1 Even parity Bit

d) 7-input XOR, input data 1011011 = 1 Even parity Bit

Explanation:

a) 4-input XOR, input data-1001  ;  generates 0 Even parity Bit

b)  5-input XOR, input data-10010 ; generates 0 Even parity Bit  

c) 6-input XOR, input data-101001 ; generates 1 Even parity Bit

d) 7-input XOR, input data 1011011 ; generates 1 Even parity Bit

Attached below is the Logic circuits of the data inputs

A find the ganeral solution to this equation

An object moving through the water has an initial velocity of 40 m/s. Two seconds later, the velocity has decreased to 30 m/s. The velocity after ten seconds is 0.

Velocity is defined as the speed at which an object's position changes in relation to time and a frame of reference.  Speed is the rate at which an object travels along a path over time, whereas velocity is the speed and direction of an item's motion. In other words, speed is a scalar value, but velocity is a vector.

As given

Initial velocity = 40 m / sec

Velocity after 2 seconds = 30 m / sec

So the velocity after 10 seconds will be = 0 m / sec

That is the object will stop moving.

Thus. an object moving through the water has an initial velocity of 40 m/s. Two seconds later, the velocity has decreased to 30 m/s. The velocity after ten seconds is 0.

To learn more about velocity, refer to the link below:

https://brainly.com/question/28738284

#SPJ2

Your question is incomplete, but probably your complete question was