Answer: Plot of [tex]\log y[/tex] vs [tex]x[/tex] would be linear with a slope of 4.
Explanation:
Given
Equation is [tex]y=10^{4x}[/tex]
Taking log both sides
[tex]\Rightarrow \log y=4x\log (10)\\\Rightarrow \log y=4x[/tex]
It resembles with linear equation [tex]y=mx+c[/tex]
Here, slope of [tex]\log y[/tex] vs [tex]x[/tex] is 4.
To avoid a possible collision with a manned airplane, you climb your unmanned aircraft to yield the right of way. In doing so, your unmanned aircraft reached an altitude greater than 600 feet AGL. To whom must you report the deviation?
Answer:
you have to report to the federal aviation administration upon request
Explanation:
An unmanned aircraft can also be a drone it is an aircraft that does not have passengers or a human pilot.
Such an aircraft could be fully autonomous but most times they have a human pilot who controls it remotely.
Now you have to report this deviation to the federal aviation administration. This body is responsible for the enforcement of regulations that have to do with the manufacture, operation and maintenance of aircrafts. The body makes sure there is an efficient and safe system for a navigation and they also control air traffic.
once scientist has asked a question conducted an investigation and analyzed the data his or hwr goalis to
Answer:
hola
Explanation:
Explanation:
so its an question?..........
A 40kg steel casting (Cp=0.5kJkg-1K-1) at a temperature of 4500C is quenched in 150kg of oil (Cp=2.5kJkg-1K-1) at 250C. If there are no heat losses, what is the change in entropy of?
(i) The casing.
(ii) The oil.
(iii) Both considered.
I want to explain what 2000 feet looks like to young children so that they can imagine it in class
Answer:
maybe take a really common toy kids play with or often see, find the average height for the toy and do the math to see how many of those toys stacked ontop of eachother would make up 2000 feet. For example (this isn't accurate btw just an idea of what it would sound like but) "Have you ever seen a barbie doll? well if you stack 400 barbie dolls ontop of their head it would be equal to 2000 feet."
Explanation:
sometimes taking common or beloved objects children have into your examples makes them have a better image of how small or how big something is.
By using order of magnitude analysis, the continuity and Navier-Stokes equations can be simplified to the Prandtl boundary-layer equations. For steady, incompressible, and two-dimensional flow, neglecting gravity, the result is delta u/ delta x + delta v/ delta y= 0; u delta u/ delta x +v delta u/ delta y= -1/p(delta u/ delta x)+ v delta^2 u/ delta y^2 Use L and V0 as characteristic length and velocity, respectively. Non-dimensionalize these equations and identify the similarity parameters that result.
Answer: Attached below is the well written question and solution
answer:
i) Attached below
ii) similar parameter = [tex]\frac{V}{VoL } = 1 / Re[/tex]
Explanation:
Using ; L as characteristic length and Vo as reference velocity
i) Nondimensionalize the equations
ii) Identifying similarity parameters
the similar parameters are = [tex]\frac{V}{VoL } = 1 / Re[/tex]
Attached below is the detailed solution
Hãy trình bày các bộ phận chính trong một bộ điều khiển điện tử (ECU) dùng trên ô tô. Cho biết công dụng của từng thành phần.
Answer:
sorry but I can't understand this Language.
Explanation:
unable to answer sorry
Question 1 of 8.
What should you do to drive safely in the station?
Turn on your hazard lights
Roll your windows down and turn off the radio
Maintain idle speed (below 5mph)
All of the above
Mark for follow up
Answer: all of the above
Explanation:
To drive safely in the station, the correct option is D. All of the above.
It should be noted that when a person is driving, it's essential for the person to drive carefully in a station.
One should not smoke in a station. Also, it's important that the driver should turn on their hazard lights
Furthermore, it's important for one to roll their windows down, turn off the radio and also maintain idle speed.
In conclusion, the correct option is D.
Read related link on:
https://brainly.com/question/18889428
Tech A says that the voltage regulator controls the strength of the rotor s magnetic field. Tech B says that the voltage regulator is installed between the output terminal of the alternator and the positive terminal of the battery. Who is correct?
Answer:
Voltage Regulator
Technician A is correct.
Explanation:
Technician B is not correct. The voltage regulator is not installed between the output terminal of the alternator and the positive terminal of the battery as claimed by Technician B. Technician A's opinion that the voltage regulator controls the strength of the rotor's magnetic field is correct. The computer can also be used to control the output of the alternator by controlling the field current.
On calculating which of the following quantities , does the body have an effect in simple projectile motion?
Answer:
Force is a kinetic quantity. Force = m x a. Hence, the mass of the body has an effect on force calculation.
The number-average molecular weight of a poly (styrene-butadiene) alternating copolymer is 1,350,000 g/mol. What is the average number of styrene and butadiene repeat units per molecule.
a) 6,806
b) 6,944
c) 4,801
d) 8,544
Question in Statistics and Probability 2
Petrol samples were taken at three different stations along a national highway to determine whether the octane rating varied from one station to another. Six petrol specimens of the same category were randomly selected at each station in different days. We are interested to know if there is sufficient evidence to indicate a difference in the mean octane rating at the different stations.
State the Null and the Alternative Hypotheses.
Which of the following is not a category of electrical burns
If OSHA determines that an employer's response to a non-formal complaint is adequate, what options does the employee filing the non-formal complaint have?
Which statement describes the relay between minerals and rocks ?
Answer:
•○●□■hey hi!■□●○•Explanation:
Minerals and rocks are the same. Aggregates of minerals form rocks. Minerals determine the texture of a rock. Most rocks are made of a single mineral type.
☆♡hope this helps♡☆Plexiglas, polymethylmethacrylate (PMMA), is often used as display windows and cases in art galleries and museums. If its flame imparts 32 kW/m^2 to the surface when it burns estimate the energy release rate of a 3 m^2 square sheet (one side). Assume its vaporization temperature is 350°C. Calculate with units, provide work.
This question is incomplete, the complete question is;
Plexiglas, polymethylmethacrylate (PMMA), is often used as display windows and cases in art galleries and museums. If its flame imparts 32 kW/m^2 to the surface when it burns estimate the energy release rate of a 3 m^2 square sheet (one side). Assume its vaporization temperature is 350°C. Calculate with units, provide work.
a ⇒ [tex]q_{rad[/tex] = σT⁴, where σ = 5.67 × 10⁻¹¹ kW/m².K⁴
b ⇒ [tex]q"[/tex] = [tex]q_{flame[/tex] - [tex]q_{rad[/tex]
c ⇒ [tex]m"[/tex] = [tex]q"[/tex]/L, where L = 1.6 kJ/g
d ⇒ Q = [tex]m"[/tex] × A × ΔHc, where ΔHc is 24.9 kJ/g
Answer:
a) [tex]q_{rad[/tex] = 8.54 kW/m²
b) [tex]q"[/tex] = 23.46 kW/m²
c) [tex]m"[/tex] = 14.6625 g/m²
d) Q = 1095.2888 kJ
Explanation:
Given the data in the question;
[tex]q_{flame[/tex] = 32 kW/m²
Area; A = 3m²
vaporization temperature; T = 350°C = ( 350 + 273 )K = 623 K
Now,
a) ⇒ [tex]q_{rad[/tex] = σT⁴, where σ = 5.67 × 10¹¹ kW/m².K⁴
we substitute
[tex]q_{rad[/tex] = ( 5.67 × 10⁻¹¹ kW/m².K⁴ ) × ( 623 K)⁴
[tex]q_{rad[/tex] = ( 5.67 × 10⁻¹¹ kW/m².K⁴ ) × 150644120641 K⁴
[tex]q_{rad[/tex] = 8.54 kW/m²
b) ⇒ [tex]q"[/tex] = [tex]q_{flame[/tex] - [tex]q_{rad[/tex]
we substitute
[tex]q"[/tex] = 32 kW/m² - 8.54 kW/m²
[tex]q"[/tex] = 23.46 kW/m²
c) ⇒ [tex]m"[/tex] = [tex]q"[/tex]/L, where L = 1.6 kJ/g
we substitute
[tex]m"[/tex] = 23.46 / 1.6
[tex]m"[/tex] = 14.6625 g/m²
d) ⇒ Q = [tex]m"[/tex] × A × ΔHc, where ΔHc is 24.9 kJ/g
we substitute
Q = 14.6625 × 3 × 24.9
Q = 1095.2888 kJ
The load on a bolt consists of an axial pull of 10 KN together with a transverse shear force of 5 KN. Find the diameter of bolt required according to I. Maximum principal stress theory; 2. Maximum shear stress theory; 3. Maximum principal strain theory, 4. Maximum strain energy theory, and 5 Maximum distortion energy theory. Take permissible tensile stress at elastic limit = 100 MPa and poisson's ratio = 0.3
Answer:
hey. its a big question. solved from *c hegg
Explanation:
determine if the fluid is satisfied
1025 steel wire is stretched with a stress of 70 MPa at room temperature 20 C. If th length is held constant, to what temperature in 'C and 'F must the wire be heated to reduce the stres to 17 MPa?
Check attached pictureCheck attached pictureCheck attached pictureCheck attached picture
Explain moment of inertia
Answer:
The moment of inertia is basically a physical quantity which describes how easy it is for a body to rotate itself around a given axis.
In easier wording: Moment of Inertia is a body and when it starts rotating or moving, it will keep doing so until we stop it by force.
Explanation:
For example, a car that is moving and active will continue to move even if you were to switch the engine off.
A systems analyst is concerned that the current authentication system may not provide the appropriate level of security. The company has integrated WAYF within its federation system and implemented a mandatory two-step authentication system. Some accounts are still becoming compromised via phishing attacks that redirect users to a fake portal, which is automatically collecting and replaying the stolen credentials.
Which of the following is a technical solution that would BEST reduce the risk of similar compromises?
A. Security awareness training
B. Push-based authentication
C. Software-based TOPT
D. OAuth tokens
E. Shibboleth
Report of invertor to convert 12 volt to 220 volt.
______ is not a type of digital signaling technique
Answer:
Data Rate Signaling
Consider CO at 500 K and 1000 kPa at an initial state that expands to a final pressure of 200 kPa in an isentropic manner. Report the final temperature in units of K and using three significant digits.
Answer:
[tex]T_2=315.69k[/tex]
Explanation:
Initial Temperature [tex]T_1=500K[/tex]
Initial Pressure [tex]P_1=1000kPa[/tex]
Final Pressure [tex]P_2=200kPa[/tex]
Generally the gas equation is mathematically given by
[tex]\frac{T_2}{T_1}=\frac{P_2}{P_1}^{\frac{n-1}{n}}[/tex]
Where
n for [tex]CO=1.4[/tex]
Therefore
[tex]\frac{T_2}{500}=\frac{200}{1000}^{\frac{1.4-1}{1.4}}[/tex]
[tex]T_2=315.69k[/tex]
8.50 nC of charge is uniformly distributed along a thin rod of length L = 9.20 cm, which is then bent into a semicircle. What is the magnitude of the electric field at the center of the circle
Solve using Matlab the problems:
One using the permutation of n objects formula
One using the permutation of r objects out of n objects
You can pick these problems from the textbook or you can make up your own questions.
Help me pleaseeeee
Answer:
Explanation:
% Clears variables and screen
clear; clc
% Asks user for input
n = input('Total number of objects: ');
r = input('Size of subgroup: ');
% Computes and displays permutation according to basic formulas
p = 1;
for i = n - r + 1 : n
p = p*i;
end
str1 = [num2str(p) ' permutations'];
disp(str1)
% Computes and displays combinations according to basic formulas
str2 = [num2str(p/factorial(r)) ' combinations'];
disp(str2)
=================================================================================
Example: check
How many permutations and combinations can be made of the 15 alphabets, taking four at a time?
The answer is:
32760 permutations
1365 combinations
==================================================================================
Flat plate collector can provide temperature upto_____
Answer:
80⁰C
Explanation:
80°C.
Normal flat plate collectors can deliver heat at temperatures up to 80°C. Deficiency rates for normal flat plate collectors can be classified as visual losses, which produce with cumulative angles of the incident sunshine, and thermal losses, which upsurge fast with the working temperature intensities
Hãy tính phản lực liên kết tại ngàm A, bản lề C và gói di động D biết p=400N/m
P1=100N
P2=200
P3=300
M1=100N/m
N2=200N/m
Answer:
say in English plz I don't understand
Can you help me check on which platform is this website created on -
https://www.virtualoplossing.info/
Answer:
It is created on Microsoft Edge
Explanation:
A one electron species, Xm, where m is the charge of the one electron species and X is the element symbol, loses its one electron from its ground state when it absorbs 7.84×10−17 J of energy. Using the prior information, the charge of the one electron species is?
Answer:
c +5
Explanation:
we have difference in energy =
2.18x10⁻¹⁸ x z² / n²
now n = 1
amount of energy absorbed Δdelta = 7.84×10−17 J
7.84×10⁻¹⁷ = 2.18x10⁻¹⁸ x z²
we divide through by 2.18x10⁻¹⁸
z² = 7.84×10⁻¹⁷ / 2.18x10⁻¹⁸
z² = 35.9633
z = √35.9633
z = 5.9969
≈ 6
charge = atomic number 6 - number of electrons available in the element 1
= 6-1 = 5
from the calculations above, the charge of the one electron specie would be c +5
State three types of maintenance.
Answer:
Tradicionalmente, se han distinguido 5 tipos de mantenimiento, que se diferencian entre sí por el carácter de las tareas que incluyen:
Explanation:
Mantenimiento Correctivo: Es el conjunto de tareas destinadas a corregir los defectos que se van presentando en los distintos equipos y que son comunicados al departamento de mantenimiento por los usuarios de los mismos.
Mantenimiento Preventivo: Es el mantenimiento que tiene por misión mantener un nivel de servicio determinado en los equipos, programando las intervencions de sus puntos vulnerables en el momento más oportuno. Suele tener un carácter sistemático, es decir, se interviene aunque el equipo no haya dado ningún síntoma de tener un problema.
Mantenimiento Predictivo: Es el que persigue conocer e informar permanentemente del estado y operatividad de las instalaciones mediante el conocimiento de los valores de determinadas variables, representativas de tal estado y operatividad. Para aplicar este mantenimiento, es necesario identificar variables físicas (temperatura, vibración, consumo de energía, etc.) cuya variación sea indicativa de problemas que puedan estar apareciendo en el equipo. Es el tipo de mantenimiento más tecnológico, pues requiere de medios técnicos avanzados, y en ocasiones, de fuertes conocimientos matemáticos, físicos y/o técnicos.
Mantenimiento Cero Horas (Overhaul): Es el conjunto de tareas cuyo objetivo es revisar los equipos a intervalos programados bien antes de que aparezca ningún fallo, bien cuando la fiabilidad del equipo ha disminuido apreciablemente de manera que resulta arriesgado hacer previsiones sobre su capacidad productiva. Dicha revisión consiste en dejar el equipo a Cero horas de funcionamiento, es decir, como si el equipo fuera nuevo. En estas revisiones se sustituyen o se reparan todos los elementos sometidos a desgaste. Se pretende asegurar, con gran probabilidad un tiempo de buen funcionamiento fijado de antemano.
Mantenimiento En Uso: es el mantenimiento básico de un equipo realizado por los usuarios del mismo. Consiste en una serie de tareas elementales (tomas de datos, inspecciones visuales, limpieza, lubricación, reapriete de tornillos) para las que no es necesario una gran formación, sino tal solo un entrenamiento breve. Este tipo de mantenimiento es la base del TPM (Total Productive Maintenance, Mantenimiento Productivo Total).
