A hypothetical A-B alloy of composition 53 wt% B-47 wt% A at some temperature is found to consist of mass fractions of 0.5 for both and phases. If the composition of the phase is 92 wt% B-8 wt% A, what is the composition of the phase
Answer:
the composition of the ∝ phase C∝ = 14 or [ 14 wt% B-86 wt% A ]
Explanation:
Given the data in the question;
Co = 53 or [ 53 wt% B-47 wt% A ]
W∝ = 0.5 = Wβ
Cβ = 92 or [ 92 wt% B-8 wt% A ]
Now, lets set up the Lever rule for W∝ as follows;
W∝ = [ Cβ - Co ] / [ Cβ - C∝ ]
so we substitute our given values into the expression;
0.5 = [ 92 - 53 ] / [ 92 - C∝ ]
0.5 = 39 / [ 92 - C∝ ]
0.5[ 92 - C∝ ] = 39
46 - 0.5C∝ = 39
0.5C∝ = 46 - 39
0.5C∝ = 7
C∝ = 7 / 0.5
C∝ = 14 or [ 14 wt% B-86 wt% A ]
Therefore, the composition of the ∝ phase C∝ = 14 or [ 14 wt% B-86 wt% A ]
Classify each molecule as an alcohol, ketone, or aldehyde based on its name. Propanone (acetone) Choose... Ethanal Choose... 3-phenyl-2-propenal Choose... Butanone Choose... Ethanol Choose... 2-propanol Choose...
Answer:
1.) Propanone (ketone)
2.) Ethanal( aldehyde)
3.) 3-phenyl-2-propenal (aldehyde)
4.) Butanone (ketone)
5.) Ethanol ( alcohol)
6.) 2-propanol (alcohol)
Explanation:
In organic chemistry, ALCOHOL ( also known as alkanol) are compounds in which hydroxyl groups are linked to alkyl groups. They can be considered as being derived from the corresponding alkanes by replacing the hydrogen atoms with hydroxyl groups. The hydroxyl group is the functional group of the alcohol as it is responsible for their characteristic chemical properties. A typical example of alcohol is ethanol and 2-propanol.
Alkanals or ALDEHYDES have the general formula RCHO while alkanones or KETONES have the general formula RR'CO where R and R' may be alkyl or aryl groups. The main similarity between these two classes of compounds is the presence of the carbonyl group. In aldehydes, there is a hydrogen atom attached to the carbon In the carbonyl group while there is none on the ketones.
Some common examples of ketones are Propanone, Butanone while examples of aldehydes are Ethanal and 3-phenyl-2-propenal
When 250. mg of eugenol, the molecular compound responsible for the odor of oil of cloves, was added to 100. g of camphor, it lowered the freezing point of camphor by 0.62 8C. Calculate the molar mass of eugenol.
Answer:
Molar mass for eugenol is 161.3 g/mol
Explanation:
This question talks about freezing point depression:
Our solute is eugenol.
Our solvent is camphor.
Formula to state the freezing point depression difference is:
ΔT = Kf . m . i where
ΔT = Freezing T° of pure solvent - Freezing T° of solution
In this case ΔT = 0.62°C
Kf for camphor is: 37°C /m
As eugenol is an organic compund, i = 1. No ions are formed.
To state the molar mass, we need m (molal)
Molal are the moles of solute in 1kg of solvent. Let's replace data:
0.62°C = 40 °C/m . m . 1
0.62°C / 40 m/°C = 0.0155 m
We convert mass of camphor from g to kg = 100 g . 1kg / 1000g = 0.1 kg
0.0155 molal = moles of solute / 0.1 kg
0.0155 m/kg . 0.1 kg = 0.00155 moles
We know that these moles are contained in 250 mg, so the molar mass will be:
0.25 g / 0.00155 mol = 161.3 g/mol
Notice, we convert mg to g, for the units!
Determine the empirical formula of a compound containing 47.37 grams of carbon, 10.59 grams of hydrogen, and 42.04 grams of oxygen.
In an experiment, the molar mass of the compound was determined to be 228.276 g/mol. What is the molecular formula of the compound?
For both questions, show your work or explain how you determined the formulas by giving specific values used in calculations. (10 points)
Answer:
Mass of C = 47.37g
Mass of H = 10.59g
Mass of O = 42.04g
The total mass of these elements is 100g, taking a proportion of their molar masses.
C = 47.37/12= 3.95
H = 10.59/1 = 10.59
O = 42.04/16= 2.63.
Dividing through with the smallest proportion which is 2.63
C=3.95/2.63 = 1.5
H =10.59/2.63 =4
O = 2.63/2.63= 1
Multiplying through by 2 to get a whole number.
C = 1.5x2 = 3
H= 4x2 = 8
O = 1x2= 2
The empirical formula is C3H6O2
(Empirical formula)n= molecular mass
(C3H8O2)n =228.276
(12x3 +8+16x2)n= 228.276
76n = 228.276
n = 228.276/76
n = 3
Molecular formula = Empirical formula
=(C3H8O2)3 = C9H24O6
The molecular formula is C9H24O6
once formed, how are coordinate covalent bonds different from other covalent bonds?
Answer:
[tex]\boxed {\boxed {\sf {One \ atom \ donates \ both \ electrons \ in \ a \ pair}}}[/tex]
Explanation:
A covalent bond involves the sharing of electrons to make the atoms more stable, and so they satisfy the Octet Rule (8 valence electrons).
Typically each atom contributes an electron to form an electron pair. This is a single bond. There are also double bonds (two pairs of electrons), triple bonds (three pairs of electrons), and coordinate covalent bonds.
Sometimes, to satisfy the Octet Rule and achieve stability, one atom contributes both of the electrons in an electron pair. This is different from other covalent bonds because usually each of the 2 atoms contributes an electron to make a pair.
Which intermolecular force plays a pivotal role in biological molecules such as proteins and DNA ?
•hydrogen bonding
•dispersion force
•dipole-dipole force
•Ion-dipole force
Answer:
hydrogen bonding
Explanation:
just took the test :D
In the given range,at what temperature does oxy gen have the highest solubility?
A student prepares a aqueous solution of acetic acid . Calculate the fraction of acetic acid that is in the dissociated form in his solution. Express your answer as a percentage. You will probably find some useful data in the ALEKS Data resource.
Answer:
10.71%
Explanation:
The dissociation of acetic acid can be well expressed as follow:
CH₃COOH ⇄ CH₃COO⁻ + H⁺
Let assume that the prepared amount of the aqueous solution is 14mM since it is not given:
Then:
The I.C.E Table is expressed as follows:
CH₃COOH ⇄ CH₃COO⁻ + H⁺
Initial 0.0014 0 0
Change - x +x +x
Equilibrium (0.0014 - x) x x
Recall that:
Ka for acetic acid CH₃COOH = 1.8×10⁻⁵
∴
[tex]K_a = \dfrac{[x][x]]}{[0.0014-x]}[/tex]
[tex]1.8*10^{-5} = \dfrac{[x][x]]}{[0.0014-x]}[/tex]
[tex]1.8*10^{-5} = \dfrac{[x]^2}{[0.0014-x]}[/tex]
[tex]1.8*10^{-5}(0.0014-x) = x^2[/tex]
[tex]2.52*10^{-8} -1.8*10^{-5}x = x^2[/tex]
[tex]2.52*10^{-8} -1.8*10^{-5}x - x^2 =0[/tex]
By rearrangement:
[tex]- x^2 -1.8*10^{-5}x +2.52*10^{-8}= 0[/tex]
Multiplying through by (-) and solving the quadratic equation:
[tex]x^2 +1.8*10^{-5}x-2.52*10^{-8}= 0[/tex]
[tex](-0.00015 + x) (0.000168 + x) =0[/tex]
x = 0.00015 or x = -0.000168
We will only consider the positive value;
so x=[CH₃COO⁻] = [H⁺] = 0.00015
CH₃COOH = (0.0014 - 0.00015) = 0.00125
However, the percentage fraction of the dissociated acetic acid is:
[tex]= \dfrac{ 0.00015}{0.0014}\times 100[/tex]
= 10.71%
What is the specific rotation of 13g of a molecule dissolved in 10 mL of solvent that gives an observed rotation of 23 degrees in a sample tube of 10 cm.
Answer:
[tex]\alpha=17.7[/tex]
Explanation:
From the question we are told that:
Mass [tex]m=13g[/tex]
Volume [tex]V=10mL[/tex]
Angle [tex]\theta=23[/tex]
Sample Tube=10cm
Generally the equation for concentration is mathematically given by
[tex]C=m/v[/tex]
[tex]C=\frac{13}{10}\\C=1.3g/mL[/tex]
Therefore the Specific Rotation
[tex]\alpha=frac{\theta }{m*l}[/tex]
[tex]\alpha=frac{23 }{1.3*1.0}[/tex]
[tex]\alpha=17.7[/tex]
What is the energy change when 78.0 g of Hg melt at −38.8°C
Answer:
The correct answer is - 2.557 KJ
Explanation:
In this case, Hg is melting, the process is endothermic, so the energy change will have a positive sign.
we can calculate this energy by the following formula:
Q = met
where, m = mass,
e = specific heat
t = temperature
then,
Q = 78*0.14* (273-38.8)
here 0.14 = C(Hg)
= 2.557 Kj
How can a Bose-Einstein condensate be formed? A. B super-heating a gas. B. By super-cooling certain types of solid. C. By super-cooling certain types of plasma. D. By super-heating a plasma
Answer:
C. By super-cooling certain types of plasma.
Explanation:
Bose-Einstein condensate is a state of matter whereby atoms or particles become cooled to a very low energy state leading to their condensation to give a single quantum state.
Note that plasma refers to atoms that have had some or even all of its electrons stripped away leaving only positively charged ions. Simply put, plasma is ionized matter.
When certain types of plasma are super cooled, Bose-Einstein condensate are formed.
Consider the reaction “2 SO2 (g) + O2 (g) = 2 SO3 was 0.175 M. After 50 s the concentration of SO2 Date: (g)”. Initial concentration of SO2 (g) (g) became 0.0500 M. Calculate rate of the reaction
Answer:
The answer is "[tex]1.25 \times 10^{-3} \ \frac{m}{s}[/tex]"
Explanation:
Calculating the rate of the equation:
[tex]=-\frac{1}{2} \frac{\Delta [SO_2]}{\Delta t} =-\frac{\Delta [O_2]}{\Delta t}= +\frac{1}{2} \frac{\Delta [SO_3]}{\Delta t}\\\\=\frac{\Delta [SO_2]}{\Delta t}=\frac{0.0500-0.175\ M}{505}= -2.5 \times 10^{-3} \ \frac{m}{s}\\\\[/tex]
Rate:
[tex]=\frac{-2.5 \times 10^{-3}}{2}=1.25 \times 10^{-3} \ \frac{m}{s}[/tex]
Consider the following reaction:
CO(g)+2H2(g)⇌CH3OH(g)
A reaction mixture in a 5.15-L flask at a certain temperature initially contains 26.6 g CO and 2.36 g H2. At equilibrium, the flask contains 8.63 g CH3OH.
Part A
Calculate the equilibrium constant (Kc) for the reaction at this temperature.
Answer:
26.6
Explanation:
Step 1: Calculate the molar concentrations
We will use the following expression.
M = mass solute / molar mass solute × liters of solution
[CO]i = 26.6 g / (28.01 g/mol) × 5.15 L = 0.184 M
[H₂]i = 2.36 g / (2.02 g/mol) × 5.15 L = 0.227 M
[CH₃OH]e = 8.63 g / (32.04 g/mol) × 5.15 L = 0.0523 M
Step 2: Make an ICE chart
CO(g) + 2 H₂(g) ⇄ CH₃OH(g)
I 0.184 0.227 0
C -x -2x +x
E 0.184-x 0.227-2x x
Since [CH₃OH]e = x, x = 0.0523
Step 3: Calculate all the concentrations at equilibrium
[CO]e = 0.184-x = 0.132 M
[H₂]e = 0.227-2x = 0.122 M
[CH₃OH]e = 0.0523 M
Step 4: Calculate the equilibrium constant (Kc)
Kc = [CH₃OH] / [CO] [H₂]²
Kc = 0.0523 / 0.132 × 0.122² = 26.6
What direction would equilibrium moves towards based on the following if we increased the volume of the container.
[tex]2A_{(g)} + 5B_{(g)} + 12C_{(g)}[/tex] ↔ [tex]14AC_{(g)} + 5B_{(s)}[/tex]
Answer choices:
a) reactants
b) no change
c) products
d) decrease in volume
Please help!
To answer this question, we will first find out the number of gaseous moles on each side of the equilibrium
on the left:
we have 2 moles of A, 5 moles of B and 12 moles of C
which gives us a grand total of 19 gaseous moles
on the right:
here, we have 14 moles of AC gas, we will not count the number of moles of B because it's a solid
giving us 14 gaseous moles on the right
Where does the reaction shift?
more gaseous moles means more space taken, because gas likes to fill all the space it can
if we have more volume, more gas can move around without colliding (reacting) with each other
Hence more volume favors the side with more gaseous moles
here, the left has more gaseous moles. So we can say that the reaction will shift towards the left, or the reactants side
Answer:
Explanation:
given reversible chemical reaction:
2A(g) + 5B(g) + 12C(g) ↔ 14AC(g) + 5B(s)
chemicals in solid form do not take up a lot of volume so change in container volume has no effect
look at chemicals in gas form only:
the total no. of moles of reactants in gas form = 2 + 5 + 12 = 19
the total no. of moles of products in gas form = 14
so an increase in volume of the container will favor the reaction direction with higher volume n high volume means higher no. of moles
the ans is the equilibrium will move towards a) reactants
Question In nickel-cadmium batteries: Select the correct answer below: the anodes are nickel-plated and the cathodes are cadmium-plated the anodes are cadmium-plated and the cathodes are nickel-plated both the anodes and cathodes are plated with a nickel-cadmium alloy none of the above
Answer:
the anodes are cadmium-plated and the cathodes are nickel-plated
Explanation:
Nickel cadmium battery works on the principle as by the other cell. There is anode and a cathode which is separated by a separator (spiral shaped inside the case). The anode is negative and is cadmium plated while the cathode is positive and is nickel plated. An electrolyte is also used.
So the correct answer is : "The anodes are cadmium-plated and the cathodes are nickel-plated."
Read the chemical equation.
N2 + 3H2 - 2NH3
Using the volume ratio, determine how many liters of NH3 is produced if 4.2 liters of H2 reacts with an excess of N2
if all measurements are taken at the same temperature and pressure?
A 2.8 liters
B 3.2 liters
C 5.4 liters
D 6.3 liters
Answer:
A 2.8 liters
Explanation:
Step 1: Write the balanced equation
N₂ + 3 H₂ ⇄ 2 NH₃
Step 2: Establish the appropriate volume ratio
At the same temperature and pressure, the volume ratio of H₂ to NH₃ is 3:2.
Step 3: Calculate the volume of ammonia produced from 4.2 L of hydrogen
4.2 L H₂ × 2 L NH₃/3 L H₂ = 2.8 L
Determine the equilibrium constant, Keq, at 25°C for the reaction
2Br- (aq) + I2(s) <--> Br2(l) + 2I- (aq)
Eocell = (0.0257/n) lnKeq, Calculate Eocell from Use this equation to calculate K value.
Eo (I2/I-) = +0.53, Eo (Br2/Br-) = +1.07,
Explanation:
The given chemical reaction is:
[tex]2Br^- (aq) + I_2(s) <-> Br_2(l) + 2I^- (aq)[/tex]
[tex]E^ocell=oxidation potential of anode + reduction potential of cathode\\[/tex]
The relation between Eo cell and Keq is shown below:
[tex]deltaG=-RTlnK_e_q\\delta=-nFE^o cell\\=>nFE^o cell=RTlnK_e_q\\lnK_e_q=\frac{nF}{RT} E^o cell[/tex]
The value of Eo cell is:
Br- undergoes oxidation and I2 undergoes reduction.
Reduction takes place at cathode.
Oxidation takes place at anode.
Hence,
[tex]E^ocell= (-1.07+0.53)V\\=-0.54V[/tex]
F=96485 C/mol
n=2 mol
R=8.314 J.K-1.mol-1
T=298K
Substitute all these values in the above formula:
[tex]ln K_e_q=\frac{2mol* 96485 C/mol}{8.314 J.K^-^1.mol^-^1x298K} \\\\lnK_e_q=77.8\\K_e_q=e^7^7^.^8\\=>K_e_q=6.13x10^3^3[/tex]
Answer:
Keq=6.13x10^33
A uniform plastic block floats in water with 50.0 % of its volume above the surface of the water. The block is placed in a second liquid and floats with 23.0 % of its volume above the surface of the liquid.
What is the density of the second liquid?
Express your answer with the appropriate units.
Answer:
density of second liquid = 650 kg/m³
Explanation:
Given that:
The volume of the plastic block submerged inside the water = 0.5 V
The force on the plastic block = [tex]\rho_1V_1g[/tex]
[tex]= 0.5p_1 V_g[/tex]
when the block is floating, the weight supporting the force (buoyancy force) is:
W [tex]= 0.5p_1 V_g[/tex]
[tex]\rho Vg = 0.5p_1 V_g[/tex]
[tex]\rho = 0.5 \rho _1[/tex]
where;
water density [tex]\rho _1[/tex] = 1000
[tex]\rho = 0.5 (1000)[/tex]
[tex]\rho = 500 kg/m^3[/tex]
In the second liquid, the volume of plastic block in the water = (100-23)%
= 77% = 0.7 V
The force on the plastic block is:
[tex]= 0.77p_2 V_g[/tex]
when the block is floating, the weight supporting the force (buoyancy force) is:
[tex]W = 0.77p_2 V_g[/tex]
[tex]\rho Vg = 0.77 \rho_2 V_g \\ \\ \rho = 0.77 \rho_2 \\ \\ 500 = 0.77 \rho_2 \\ \\ \rho_2 = 500/0.77[/tex]
[tex]\mathbf{ \rho_2 \simeq 650 \ kg/m^3}[/tex]
Write a net ionic equation for the overall reaction that occurs when aqueous solutions of carbonic acid and sodium hydroxide are combined. Assume excess base.
Answer:
[tex]H_2CO_3(aq)+2OH^-(aq)\rightarrow (CO_3)^{2-}(aq)+2H_2O(l)[/tex]
Explanation:
Hello there!
In this case, according to the given information, it turns out possible for us to set up this net ionic equation, by firstly setting up the complete molecular equation as follows:
[tex]H_2CO_3(aq)+2NaOH(aq)\rightarrow Na_2CO_3(aq)+2H_2O(l)[/tex]
Thus, since carbonic acid is weak it merely ionizes whereas sodium hydroxides ionizes for the 100 % as it is strong; thus, we can write the complete ionic equation:
[tex]H_2CO_3(aq)+2Na^+(aq)+2OH^-(aq)\rightarrow 2Na^+(aq)+(CO_3)^{2-}(aq)+2H_2O(l)[/tex]
Whereas sodium ions act as the spectator ones to be cancelled out for us to obtain:
[tex]H_2CO_3(aq)+2OH^-(aq)\rightarrow (CO_3)^{2-}(aq)+2H_2O(l)[/tex]
Regards!
A sample of oxygen occupies 1.00 L. If the temperature remains constant, and the pressure on the oxygen is decreased to one third the original pressure, what is the new volume
Answer:
3.00 L
Explanation:
P₁V₁ = P₂V₂
V₁ = 1.00 L
P₁ = (x) atm
P₂ = [tex]\frac{1}{3}[/tex] · (P₁) = [tex]\frac{x}{3}[/tex]
V₂ = unknown
(x atm)(1.00 L) = ( [tex]\frac{x}{3}[/tex] atm)(V₂)
divide both sides by ( [tex]\frac{x}{3}[/tex] atm)
( 1.00x )( [tex]\frac{3}{x}[/tex] ) = V₂
x cancels out
(1.00)(3) = V₂
V₂ = 3.00 L
Write a balanced half-reaction for the oxidation of liquid water to aqueous hydrogen peroxide in basic aqueous solution. Be sure to add physical state symbols where appropriate.
Answer:
O2(g) + 2H2O(l) --------> 2H2O2(aq) + 2e
Explanation:
An oxidation reaction reaction refers to a reaction in which electrons are lost. In this case, we are about to see the full balanced half-reaction for the oxidation of liquid water to aqueous hydrogen peroxide in basic aqueous solution.
The full equation is;
O2(g) + 2H2O(l) --------> 2H2O2(aq) + 2e
So, two electrons were lost in the process.
What is "X" in the following reaction?
For each of the following compounds, indicate the pH at which 50% of the compound will be in a form that possesses a charge and at which pH more than 99% of the compound will be in a form that possesses a charge.
ClCH2COOH (pKa = 2.86)
CH3CH2NH+3 (pKa = 10.7)
Express your answer using two decimal places
a. Determine a pH at which 50% of ClCH2COOH will be in a form that possesses a charge.
b. Determine a pH at which pH more than 99% of ClCH2COOH will be in a form that possesses a charge.
c. Determine a pH at which 50% of CH3CH2NH+3 will be in a form that possesses a charge.
d. Determine a pH at which pH more than 99% of CH3CH2NH+3 will be in a form that possesses a charge.
Answer:
a. 2..86 b. 4.86 c. 10.7 d. 8.7
Explanation:
a. Determine a pH at which 50% of ClCH2COOH will be in a form that possesses a charge.
Using the Henderson-Hasselbalch equation,
pH = pKa + log[A⁻]/[HA]
where [A⁻] = concentration of conjugate base (or charged form) and [HA] = concentration of acid.
At 50% concentration, [A⁻] = [HA] ⇒ [A⁻]/[HA] = 1
So, pH = pKa + log[A⁻]/[HA]
pH = pKa + log1
pH = pKa = 2.86
b. Determine a pH at which pH more than 99% of ClCH2COOH will be in a form that possesses a charge.
Let x be the concentration of the acid. Since 99% of it should possess a charge, the basic concentration is 0.99x while the acidic concentration is remaining 1 % (1 - 0.99)x = 0.01x
Using the Henderson-Hasselbalch equation,
pH = pKa + log[A⁻]/[HA] where [A⁻] = concentration of conjugate base (or charged form) = 0.99x and [HA] = concentration of acid = 0.01x.
pH = pKa + log0.99x/0.01x
pH = pKa + log0.99/0.01
pH = 2.86 + log99
pH = 2.86 + 1.996
pH = 4.856
pH ≅ 4.86
c. Determine a pH at which 50% of CH3CH2NH+3 will be in a form that possesses a charge.
Using the Henderson-Hasselbalch equation,
pH = pKa + log[A⁻]/[HA]
where [A⁻] = concentration of conjugate base and [HA] = concentration of acid.
At 50% concentration, [A⁻] = [HA] ⇒ [A⁻]/[HA] = 1
So, pH = pKa + log[A⁻]/[HA]
pH = pKa + log1
pH = pKa = 10.7
d. Determine a pH at which pH more than 99% of CH3CH2NH+3 will be in a form that possesses a charge.
Let x be the concentration of the acid. Since 99% of it should possess a charge, the basic concentration is 0.01x while the acidic concentration is remaining 99 % (1 - 0.01)x = 0.99x (which possesses the charge).
Using the Henderson-Hasselbalch equation,
pH = pKa + log[A⁻]/[HA] where [A⁻] = concentration of conjugate base = 0.01x and [HA] = concentration of acid = 0.99x.
pH = pKa + log0.01x/0.99x
pH = pKa + log1/99
pH = 10.7 - log99
pH = 10.7 - 1.996
pH = 8.704
pH ≅ 8.7
How much heat capacity, in joules and in calories, must be added to a 75.0-g iron block with a specific heat of 0.499J/g °C to increase its temperature from 25 °C to its melting temperature of 1535 °C?
Answer:
56511.75 J
13506.3 Calories
Explanation:
Applying,
Q = cm(t₂-t₁).................. Equation 1
Where Q = amount of heat, m = mass of the iron, c = specific heat capacity of the iron, t₁ = initial temperature, t₂ = final temperature.
From the question,
Given: m = 75 g, c = 0.499 J/g.°C, t₂ = 1535°C, t₁ = 25°C
Substitute these values into equation 1
Q = 75(0.499)(1535-25)
Q = 75(0.499)(1510)
Q = 56511.75 J
Q in Calories is
Q = (56511.75×0.239)
Q = 13506.3 Calories
Calculate the mass of sodium phosphate in aqueous solution to fully react with 37 g of chromium nitrate(III) an aqueous solution?(report answer in grams and only three Sigg figs do not put the unit)
Answer:
41 g
Explanation:
The equation of the reaction is;
Cr(NO3)3(aq)+Na3PO4(aq)=3NaNO3(s)+CrPO4(aq)
Number of moles of chromium nitrate = 37g/ 146.97 g/mol = 0.25 moles
1 mole of sodium phosphate reacts with 1 mole of chromium nitrate
x moles of sodium phosphate react as with 0.25 moles of chromium nitrate
x= 1 × 0.25/1
x= 0.25 moles
Mass of sodium phosphate = 0.25 moles × 163.94 g/mol
Mass of sodium phosphate = 41 g
Inter-molecular forces determine the _______________ properties while intra-molecular forces determine the ________ properties of compounds.
Answer:
Physical
Chemical
Explanation:
Intermolecular forces are the forces that hold the molecules of a substance together in a particular state of matter. They decide the physical properties of a substance.
The intra molecular forces are the bond forces that hold atoms together in molecules. The nature of this bonding determines the chemical properties of substances.
What enzyme below is an exoenzyme?
A. Casease
B. Citrase
C. Catalase
D. Oxidase
If a 0.320 mM solution of MnO41- has an absorbance of 0.480 at 525 nm in a 1.000 cm cell. What is the concentration of a MnO41- solution that has absorbance of 0.490 in the same cell at that wavelength?
Answer:
Hence the concentration of a MnO41- solution that has absorbance of 0.490 in the same cell at that wavelength is 0.3266.
Explanation:
Now A = el, el=const
Then,
[tex]A2 / A1 = C2/ C1\\\\0.49/ 0.48 = C2 / 0.32\\\\C2 = 0.3266[/tex]
1. Most of the chemicals included in your General Chemistry Lab kit can be discarded down a drain. Describe a situation in which you would need to neutralize a chemical before discarding down a drain.
Answer: Chemicals like acids and bases are harmful and must be neutralized before draining.
Explanation:
A strong acid or strong base is required to be diluted or neutralized before it is discarded in the drain as if is discarded without diluting and neutralization it can spill and splash from sink or drain and can harm people in chemistry lab, moreover the fumes of the discarded chemical on spilling can cause respiratory tract burning and can even cause fire hazard so it must be converted into less harmful form and then must be drained.
Use the Ka values for weak acids to identify the best components for preparing buffer solutions with the given pH values.
Name Formula Ka
Phosphoric acid H3PO4 7.5 x 10^-3
Acetic acid CH3COOH 1.8 x 10^-5
Formic acid HCOOH 1.8 x 10^-4
pH 1.9 =_________
pH 5.0 = ________
pH 3.9= ________
Answer:
pH= 1.9 then [tex]H_{3} PO_{4}[/tex]
pH = 5.0 , [tex]CH_{3} COOH[/tex]
pH = 3.9 , HCOOH
As we know range left [tex]pH= pKa+/- 1[/tex]
