Answer:
the number of turns in the primary coil is 13000
Explanation:
Given the data in the question;
V₁ = 13000 V
V₂ = 120 V
N₁ = ?
N₂ = 120 turns
the relation between the voltages and the number of turns in the primary and secondary coils can be expressed as;
V₁/V₂ = N₁/N₂
V₁N₂ = V₂N₁
N₁ = V₁N₂ / V₂
so we substitute
N₁ = (13000 V × 120 turns) / 120 V
N₁ = 1560000 V-turns / 120 V
N₁ = 13000 turns
Therefore, the number of turns in the primary coil is 13000
The circuit has a 3 volt EMF and two ohm resistors. How much power in watts does this circuit draw? A) 4.5 , B) 24, C) 1.13 D) 2.67 E) 0.375 F) 1.5
Answer:
P = 4.5 watts
Explanation:
Given that,
EMF of the circuit, E = 3 volt
The resistance of the resistors, R = 2 ohms
We need to find the power of this circuit. The relation between power, emf and resistance is given by the formula as follows :
[tex]P=\dfrac{V^2}{R}[/tex]
Substitute all the values,
[tex]P=\dfrac{3^2}{2}\\\\P=4.5\ W[/tex]
So, the power of this circuit is equal to 4.5 watts.
What is the order of the events for the water cycle on a typical warm day?
А
rain, snow, sleet
B
precipitation, evaporation, rain
с
evaporation, condensation, precipitation
D
condensation, evaporation, precipitation
A 101 kg basketball player crouches down 0.380 m while waiting to jump. After exerting a force on the floor through this 0.380 m, his feet leave the floor and his center of gravity rises 0.920 m above its normal standing erect position. (a) Using energy considerations, calculate his velocity (in m/s) when he leaves the floor. m/s (b) What average force (in N) did he exert on the floor
Answer:
[tex]4.25\ \text{m/s}[/tex]
[tex]3391.22\ \text{N}[/tex]
Explanation:
y = Height of compression = 0.38 m
m = Mass of basketball player = 101 kg
h = Height of center of gravity after jump = 0.92 m
g = Acceleration due to gravity = [tex]9.81\ \text{m/s}^2[/tex]
Energy balance of the system is given by
[tex]mgh=\dfrac{1}{2}mv^2\\\Rightarrow v=\sqrt{2gh}\\\Rightarrow v=\sqrt{2\times 9.81\times 0.92}\\\Rightarrow v=4.25\ \text{m/s}[/tex]
The velocity of the player when he leaves the floor is [tex]4.25\ \text{m/s}[/tex]
[tex]Fy=mgy+\dfrac{1}{2}mv^2\\\Rightarrow F=\dfrac{mgy+\dfrac{1}{2}mv^2}{y}\\\Rightarrow F=\dfrac{101\times 9.81\times 0.38+\dfrac{1}{2}\times 101\times 4.25^2}{0.38}\\\Rightarrow F=3391.22\ \text{N}[/tex]
The force exerted on the floor is [tex]3391.22\ \text{N}[/tex].
Which one of the statements below is true about mechanical waves?
They must travel in empty space.
They can travel in a vacuum.
Both sound and light are examples of mechanical waves.
They require a medium to travel through.
Answer:
Both sound and waves
Explanation:
Thank me later
Two resistors are connected in parallel. If R1 and R2 represent the resistance in Ohms (Ω) of each resistor, then the total resistance R is given by 1R=1R1+1R2. Suppose that in fact, these two resistors are actually potentiometers (resistors with variable resistance) and R1 is increasing at a rate of 0.4Ω/min and R2 is increasing at a rate of 0.6Ω/min. At what rate is R changing when R1=117Ω and R2=112Ω?
Answer:
1/Re= 1/R1 + 1/R2
Explanation:
Two resistors are connected in parallel. If R1 and R2 represent the resistance in Ohms (Ω) of each resistor, then the total resistance R is given by [tex]\mathbf{\dfrac{1}{R}=\dfrac{1}{R_1}+\dfrac{1}{R_2}}[/tex]. Thus, the rate of R changes when R₁ = 117 Ω and
R₂ = 112 Ω is 0.25 Ω/min
For a given resistor connected in parallel;
[tex]\mathbf{\dfrac{1}{R}=\dfrac{1}{R_1}+\dfrac{1}{R_2}}[/tex]
Making R from the left-hand side the subject of the formula, then:
[tex]\mathbf{R = \dfrac{R_1R_2}{R_1+R_2}}[/tex]
Given that:
[tex]\mathbf{R_1 = 117,}[/tex] [tex]\mathbf{R_2 = 112 }[/tex]Now, replacing the values in the above previous equation, we have:
[tex]\mathbf{R = \dfrac{13104}{229}}[/tex]
However, the differentiation of R with respect to time t will give us the rate at which R is changing when R1=117Ω and R2=112Ω.
So, by differentiating the given equation of the resistor in parallel with respect to time t;
[tex]\mathbf{\dfrac{1}{R}=\dfrac{1}{R_1}+\dfrac{1}{R_2}}[/tex], we have:
[tex]\mathbf{\dfrac{1}{R^2}(\dfrac{dR}{dt})=\dfrac{1}{R_1^2}(\dfrac{dR_1}{dt})+\dfrac{1}{R_2^2}(\dfrac{dR_2}{dt})}[/tex]
[tex]\mathbf{(\dfrac{dR}{dt})=R^2 \Bigg[ \dfrac{1}{R_1^2}(\dfrac{dR_1}{dt})+\dfrac{1}{R_2^2}(\dfrac{dR_2}{dt})\Bigg]}[/tex]
[tex]\mathbf{\dfrac{dR}{dt}=(\dfrac{13104}{229})^2 \Bigg[ \dfrac{0.4}{117^2}+\dfrac{0.6}{112^2}\Bigg]}[/tex]
[tex]\mathbf{\dfrac{dR}{dt}=3274.44 \Bigg[ (7.7052 \times 10^{-5} )\Bigg]}[/tex]
[tex]\mathbf{\dfrac{dR}{dt}=0.25\ \Omega /min}[/tex]
Therefore, we can conclude that the rate at which R is changing R1=117Ω and R2=112Ω is 0.25 Ω/min
Learn more about resistors here:
https://brainly.com/question/17390255?referrer=searchResults
A phase change is when a substance changes from one state of mind to nother because of the adding or removal of thermal energy
True
False
Answer:
true it all changes
Explanation:
________________________
question is included in the picture!!! PUT REAL ANSWERS OR I WILL REPORT YOU
Answer:
Explanation:
this is like rubbing a balloon on your head to make your hair stand up. Do that to the can. The balloon is filled , ofc, and then just rub the balloon on the can. This will charge the can with static electricity. :P
should scientist be allowed to do anything that they can?
No, because some scientist are bad and they must have a scientific attitude like honesty, curiosity, open-mindedness, optimistic and more. And they should follow others sometimes because for their own good.
Answer:
No
Explanation:
Science operates in the context of national and international laws, agreements and conventions. It requires scientists to conduct and communicate scientific work for the benefit of society, with excellence, integrity, respect, fairness, trustworthiness, clarity, and transparency.
Protons, neutrons, electrons, and a nucleus are
Plz answer asap I need all of the answer
Answer:
Turned up side down
Explanation:
can someone help
pls !
The photograph shows part of the Great Plains of North America. How do
plains form?
A. Magma rises at a divergent plate boundary.
B. Tectonic movements make folds and faults in the crust.
C. Continental plates slip past each other at a transform boundary.
D. Water, wind, or glaciers either remove or deposit crust.
SUBMIT
2 PREVIOUS
Answer:
Some plains form as ice and water erodes, or wears away, the dirt and rock on higher land. Water and ice carry the bits of dirt, rock, and other material, called sediment, down hillsides to be deposited elsewhere. As layer upon layer of this sediment is laid down, plains form. Volcanic activity can also form plains.
What type of feeder is a snake? *
Answer:
slender-bodied non-stinging insect having iridescent wings that are outspread at rest; adults and nymphs feed on mosquitoes etc.
Explanation:
I hope this works. I have a snake and it helps to know this stuff
Sometimes a person cannot clearly see objects close up or far away. To correct this type of vision, bifocals are often used. The top half of the lens is used to view distant objects and the bottom half of the lens is used to view objects close to the eye. Bifocal lenses are used to correct his vision. A diverging lens is used in the top part of the lens to allow the person to clearly see distant objects.
1. What power lens (in diopters) should be used in the top half of the lens to allow her to clearly see distant objects?
2. What power lens (in diopters) should be used in the bottom half of the lens to allow him to clearly see objects 25 cm away?
Answer:
1) P₁ = -2 D, 2) P₂ = 6 D
Explanation:
for this exercise in geometric optics let's use the equation of the constructor
[tex]\frac{1}{f} = \frac{1}{p} + \frac{1}{q}[/tex]
where f is the focal length, p and q are the distance to the object and the image, respectively
1) to see a distant object it must be at infinity (p = ∞)
[tex]\frac{1}{f_1} = \frac{1}{q}[/tex]
q = f₁
2) for an object located at p = 25 cm
[tex]\frac{1}{f_2} = \frac{1}{25} + \frac{1}{q}[/tex]
We can that in the two expressions we have the distance to the image, this is the distance where it can be seen clearly in general for a normal person is q = 50 cm
we substitute in the equations
1) f₁ = -50 cm
2)
[tex]\frac{1}{f_2} = \frac{1}{25} + \frac{1}{50}[/tex]
[tex]\frac{1}{f_2}[/tex] = 0.06
f₂ = 16.67 cm
the expression for the power of the lenses is
P = [tex]\frac{1}{f}[/tex]
where the focal length is in meters
1) P₁ = 1/0.50
P₁ = -2 D
2) P₂ = 1 /0.16667
P₂ = 6 D
A 20 ft ladder leans against a wall. The bottom of the ladder is 3 ft from the wall at time t=0 and slides away from the wall at a rate of 2ft/sec. Find the velocity of the top of the ladder at time t=1.
Answer: 0.516 ft/s
Explanation:
Given
Length of ladder L=20 ft
The speed at which the ladder moving away is v=2 ft/s
after 1 sec, the ladder is 5 ft away from the wall
So, the other end of the ladder is at
[tex]\Rightarrow y=\sqrt{20^2-5^2}=19.36\ ft[/tex]
Also, at any instant t
[tex]\Rightarrow l^2=x^2+y^2[/tex]
differentiate w.r.t.
[tex]\Rightarrow 0=2xv+2yv_y\\\\\Rightarrow v_y=-\dfrac{x}{y}\times v\\\\\Rightarrow v_y=-\dfrac{5}{19.36}\times 2=0.516\ ft/s[/tex]
If a virtual image is formed 10.0 cm along the principle axis from a convex mirror of focal length-15.0 cm, how far is the object from the mirror
Answer:
U=30cm
Explanation:
All you have to do is to put
Mirror formula , 1/f=1/u + 1/v
You should be careful in sign convention .
Virtual image is negative
we take focal length of convex lens negative even if its not given and so on...
What is the Lorentz force law used for? A. To find the voltage of a battery B. To find the magnitude of a magnetic force C. To find the velocity of an electromagnetic wave. D. To find the direction of a magnetic field
Answer:
B
Explanation:
The Lorentz force is the sum of the electric force and magnetic force.
F = qE + qvB
qE represents electric force and qvB represents magnetic force
A wheel rotates about a fixed axis with an initial angular velocity of 24 rad/s. During a 4 s interval the angular velocity decreases to 14 rad/s. Assume that the angular acceleration is constant during the 4 s interval. How many radians does the wheel turn through during the 4 s interval
Answer:
[tex]\theta=76\ rad[/tex]
Explanation:
Hoven that,
Initial angular velocity of the wheel = 24 rad/s
Final angular velocity = 14 m/s
Time, t = 4 s
We need to find how many radians does the wheel turn through during the 4 s interval. Let the displacement is [tex]\theta[/tex]. Using second equation of rotational kinematics to find it such that,
[tex]\theta=\omega_i t+\dfrac{1}{2}\alpha t^2[/tex]
Where
[tex]\alpha[/tex] is angular acceleration
[tex]\alpha =\dfrac{\omega_f-\omega_i}{t}\\\\\alpha =\dfrac{14-24}{4}\\\\\alpha =-2.5\ rad/s^2[/tex]
So,
[tex]\theta=24\times 4+\dfrac{1}{2}\times (-2.5)\times 4^2\\\\\theta=76\ rad[/tex]
So, it will turn 76 radian during the 4 s interval.
Tameika makes a table about sensory organs
Eye
skin
brain
tongue
Which organ should be removed from the table?
A. eye
B. skin
C. brain
D. tongue
Answer:
I think its d
Explanation:
I'm not sure I'm sorry if I'm wrong
Instead of changing the focal length of the lens, the eyes of amphibians work in a different manner: a set of muscles changes the shape of the eye which increases the distance between the front of the eye and the retina. The world's largest frog, the Goliath frog of west Africa, has an eye with a maximum size similar to a human's: 2.5cm. However, unlike a human, where the focal length is also 2.5cm, the focal length of the Goliath frog's eye is 2.146 cm. What is the maximum distance this frog can see
Answer:
The answer is "15.56 cm".
Explanation:
[tex]v= 2.5 \ cm\\\\f= 2.154 \ cm[/tex]
Calculating object of length is x so:
[tex]u= -x[/tex]
Using formula:
[tex]\to \frac{1}{v}-\frac{1}{u}=\frac{1}{f}\\\\\to \frac{1}{2.5}-\frac{1}{-x}=\frac{1}{2.154}\\\\\to \frac{1}{x}=\frac{1}{2.154}-\frac{1}{2.5}\\\\\to \frac{1}{2.5}-\frac{1}{-x}=\frac{1}{2.154}\\\\\to x= 15.56 \ cm[/tex]
An object A with mass 200 kg and an another object B with mass 1000 kg are moving with same speed. The ratio of kinetic energy of object A to B is
Answer:
Ratio of kinetic energy of object A to B = 1:5
Explanation:
Given:
Mass of object A = 200 kg
Mass of object B = 1,000 kg
Find:
Ratio of kinetic energy of object A to B
Computation:
Kinetic energy = (1/2)(m)(v²)
Kinetic energy of object A = (1/2)(200)(v²)
Kinetic energy of object A = (100)(v²)
Kinetic energy of object B = (1/2)(1,000)(v²)
Kinetic energy of object B = (500)(v²)
Ratio of kinetic energy of object A to B = Kinetic energy of object A / Kinetic energy of object B
Ratio of kinetic energy of object A to B = (100)(v²) / (500)(v²)
Ratio of kinetic energy of object A to B = 100 / 500
Ratio of kinetic energy of object A to B = 1/5
Ratio of kinetic energy of object A to B = 1:5
In many places on Earth, humans are responsible for the removal of grasses, shrubs, trees, and other plants with roots that hold soil in place. This activity is best described by which of the following? *
A) deforestation
B) urbanization
C) air pollution
D) rise in sea level
NO LINKS PLEASE
At what speed do a bicycle and its rider, with a combined mass of 90 kg
k
g
, have the same momentum as a 1500 kg
k
g
car traveling at 4.0 m/s
m
/
s
?
Answer:
2
Explanation:
convert 1 day into seconds.(you will need to show your work to receive credit.) please help thank you
Answer:
the answer is 86400seconds.
Explanation:
1day= 24 hours
24hours to seconds =
24×60×60= 86400 seconds.
( 60 second = 1 minutes)
( 60 minutes = 1 hour)
It is almost as if each outer planet is a solar system in its own right.
True or False
one negative change you may encounter as a student or an employee
Answer:
you may get bullied or teased for being a differrent race, ethnic.
Answer:
Workload
Explanation:
You may feel stressed about a heavier workload or more too do. You will also be paid as an employee unlike, a student.
Please help me someone !
Answer:
The object is moving at constant speed.
Explanation:
The spaces between the dots are equal.
What voltage would be measured across the 15 ohm resistor?
A)
2.5 volts
B)
5.0 volts
C)
7.5 volts
D)
10 volts
Answer:
7.5 volts
Explanation:
I did it on USA Testprep
What is Force ?.............
Answer:
Push or pull of an object is considered a force. Push and pull come from the objects interacting with one another. Terms like stretch and squeeze can also be used to denote force.
In Physics, force is defined as:
The push or pull on an object with mass that causes it to change its velocity.
Force is an external agent capable of changing the state of rest or motion of a particular body. It has a magnitude and a direction. The direction towards which the force is applied is known as the direction of the force and the application of force is the point where force is applied.
. Estimate the buoyant force that air exerts on you. (To do this, you can estimate your volume by knowing your weight and by assuming that your weight density is a bit less than that of water.)
Answer:
[tex]0.886[/tex] N buoyant force is exerted by air
Explanation:
My weight is [tex]75[/tex] Kg
Weight = mass * gravity
As we know
Buoyant Force is equal to the product of density * acceleration due to gravity and volume of the body
Assuming weight density is a bit less than that of water or equal to water i.e [tex]997.77[/tex] kg/m3
Volume is equal to mass / density
[tex]= 75[/tex] Kg * g/[tex]997.777[/tex]
[tex]= 0.0751[/tex] * g
Buoyant Force
= Volume * g * density
[tex]= 0.0751 * 9.8 * 1.2041[/tex]kg/m3
[tex]= 0.886[/tex] N
