Answer: The volume of given amount of ethanol at this temperature is 159.44 mL
Explanation:
Specific gravity is given by the formula:
[tex]\text{Specific gravity}=\frac{\text{Density of a substance}}{\text{Density of water}}[/tex]
We are given:
Density of water = 0.997 g/mL
Specific gravity of ethanol = 0.787
Putting values in above equation, we get:
[tex]0.787=\frac{\text{Density of a substance}}{0.997g/mL}\\\\\text{Density of a substance}=(0.787\times 0.997g/mL)=0.784g/mL[/tex]
Density is defined as the ratio of mass and volume of a substance.
[tex]\text{Density}=\frac{\text{Mass}}{\text{Volume}} [/tex] ......(1)
Given values:
Mass of ethanol = 125 g
Density of ethanol = 0.784 g/mL
Putting values in equation 1, we get:
[tex]\text{Volume of ethanol}=\frac{125g}{0.784g/mL}=159.44mL[/tex]
Hence, the volume of given amount of ethanol at this temperature is 159.44 mL
The specific heat capacity of liquid ethanol is 2.42 J/gºC.
How many joules of heat must be absorbed by 0.463 g ethanol to change its temperature from 51.6 °C to 82.4 °C?
Show work to receive credit.
Copper sulfate is made of one copper (Cu) atom, one sulfur (S) atom, and four oxygen (O) atoms. Write the chemical formula correctly.
Calculate the amount of heat required to completely sublime 55.0 g of solid dry ice CO2 at its sublimation temperature. The heat of sublimation for carbon dioxide is 32.3 kj mol
Answer:
40.4 kJ
Explanation:
Step 1: Given data
Mass of CO₂ (m): 55.0 gHeat of sublimation of CO₂ (ΔH°sub): 32.3 kJ/molStep 2: Calculate the moles corresponding to 55.0 g of CO₂
The molar mass of CO₂ is 44.01 g/mol.
n = 55.0 g × 1 mol/44.01 g = 1.25 mol
Step 3: Calculate the heat (Q) required to sublimate 1.25 moles of CO₂
We will use the following expression.
Q = n × ΔH°sub
Q = 1.25 mol × 32.3 kJ/mol = 40.4 kJ
The value of ΔH° for the reaction below is -6535 kJ. ________ kJ of heat are released in the combustion of 16.0 g of C6H6 (l)?
2C6H6 (l) + 15O2 (g) → 12CO2 (g) + 6H2O (l)
Answer:
the value of H° is below -6535 kj. +6H2O
Explanation:
6H2O answer solved
For the given reaction, 2 moles of C₆H₆ the heat energy released is - 6535 KJ. Then, for 16 g of the compound or 0.205 moles needs 669.83 KJ of heat released in combustion.
What is combustion ?Combustion is a chemical reaction that occurs between a fuel and an oxidizing agent, typically oxygen, resulting in the release of heat, light, and various combustion products, such as carbon dioxide and water vapor.
The process of combustion involves a rapid and exothermic (heat-releasing) oxidation reaction that produces a flame, which is visible in many cases.
Here, 2 moles of the hydrocarbon releases - 6535 KJ of energy.
molar mass of C₆H₆ = 78 g/mol
then no.of moles in 16 g = 16 /78 = 0.205 moles.
then energy released by 0.205 moles = 0.205 moles × 6535 KJ /2 moles = 669.83 kJ
Therefore, the heat energy released by 16 g of the compound in combustion is 669.83 kJ.
Find more on combustion :
https://brainly.com/question/13153771
#SPJ2
9. The formular for finding the area
of an object is
A. Length + Width
B. Length - Width
C. Length : Width
D. Length x Width
E. 2 (Length + Width)
ans
Answer:
D. length × width
Explanation:
eg. 30 cm(length) × 20cm(width) = 600cm²
Question 8 (5 points)
(08.02 MC)
A 10 M concentrated stock solution of NaCl was used to prepare 5 liters of diluted 1 M solution. Which of the following statements is true about
the
process used to achieve this required dilution? (5 points)
O a
The volume of stock solution used was less than 0.4 liters.
Oь
The volume of stock solution used was more than 5 liters.
Ос
The volume of the solvent used was less than 0.4 liters.
Od
The volume of the solvent used was less than 5 liters.
Answer:
d . The volume of the solvent used was less than 5 liters.
Explanation:
Hello there!
In this case, according to the given information, it turns out possible for us to calculate the volume of the stock (initial) solution by using the following equation:
[tex]M_1V_1=M_2V_2[/tex]
Thus, we solve for, V1, which stands for the aforementioned volume of stock solution:
[tex]V_1=\frac{M_2V_2}{M_1}[/tex]
Then, we plug in to obtain:
[tex]V_1=\frac{5L*1M}{10M}\\\\V_1=0.5L[/tex]
Now, since the final volume was 5 L, we can infer that the volume of solvent is 4.5 L and that of the stock solution 0.5 L for a total of 5 L of diluted solution; therefore, the correct reasoning is d . The volume of the solvent used was less than 5 liters.
Regards!
Answer:
The volume of the solvent is less than 5
Explanation:
The relationship between the volume and mass of an element is
Answer:
Density
Explanation:
The mass of an element is the average weight that the isotope of the particular element contains. Its characteristic indicates the amount of substance present in an element.
However, the volume of an element on the other hand is the mole of an element that is contained in a room temperature.
The relation joining both the mass and volume of an element is density.
This is because density showcase the relationship between the mass of an element to space in occupies in terms of volume.
It is given by the formula:
Density = mass/volume
All forms of energy can exist as either ________ or ________ energy.
Answer:
potentiol or kenetic
Explanation:
HELLLLLLLLPPPPPPPPPPPPPPPPPP
Answer:
aa
Explanation:
There is a lowercase a on both sides.
Choose true or false
1. Acetone cannot be used as a solvent because the Grignard reagent will react with its carbonyl, instead of reacting with the planned synthesis carbonyl.
2. Tetrahydrofuran is not a suitable solvent for the Grignard reaction because his oxygen may form complexes with the Mg, deactivating the Grignard.
3. Phenol can be used as a solvent in Grignard reaction as long as is anhydrous and moisture is kept out of the system with a drying tube with drierite.
4. Syringes are used in the Grignard experiment to avoid mixing all the reagents.
5. We use syringes to inject the reagents through a septum preventing moisture to enter the system.
Explanation:
Grignard reagent reacts with ketones. Upon chemical reaction of acetone and Grignard reagent there will be formation of tertiary alcohol.
1). So the statement, acetone cannot be used as a solvent because the Grignard reagent will react with its carbonyl, instead of reacting with the planned synthesis carbonyl is true.
2). Tetrahydrofuran is not a suitable solvent for the Grignard reaction because his oxygen may form complexes with the Mg, deactivating the Grignard is a false statement.
3). Phenol can be used as a solvent in Grignard reaction as long as is anhydrous and moisture is kept out of the system with a drying tube with drierite is false statement.
4). Syringes are used in the Grignard experiment to avoid mixing all the reagents is false statement.
5). We use syringes to inject the reagents through a septum preventing moisture to enter the system is true statement.
Which is most likely the reason the U.S government made such an investment
Answer:
The U.S government made such an investment because they're most likely to reduce harmful emissions.
f(x) = -x2+x+6
x
-2
a
-1
4
0
b
1
6
2
c с
do
11 11 11
Cross primary components of vascular tissue are the xylem and phloem. These two tissues transport fluid and nutrients internally. There are also two meristems associated with vascular tissue: the vascular cambium and the cork cambium. All the vascular tissues within a particular plant together constitute the vascular tissue system of that plant.
PLSSS HELP MEEEEEEEE
It takes 5 seconds for a wave with a wavelength of 0.4 m to travel past you.
What is the frequency of the wave?
A. 2.0 Hz
B. 0.2 Hz
C. 5 Hz
D. 2.5 Hz
Answer:
A
Explanation:
frequency is the product of time and wave length
Answer:
(B) 0.2Hz
Explanation:
took the test and it for sure was not 2.0Hz
What element provides strength to the exoskeleton of Clams and oysters
How is the enthalpy of reaction shown in this potential energy diagram?
Answer:
as the difference of the energy of the reactants and the energy of the products
In the given potential energy diagram, the energy of product at higher level and energy of reactant at lower level. The for this reaction will be positive. So, the enthalpy of reaction is defined as the difference of the energy of the reactants and the energy of the products.
I hope this helps!
Difference between sieving and filtration
my answer
Explanation:
Answer. Filtration is the method of separating a solid from a liquid. A sieve sets a threshold calibration through which all undersized materials pass through. Filtration differs from sieving, where separation occurs at a single perforated layer (a sieve).
Doc. No.
QMS
Rev. Date
1. In the reaction
P
> M + N
a) The reactants are:
b) The products are:
Answer: In the reaction:
a) The reactants are: P
b) The products are: M and N
Explanation:
The given reaction equation is as follows.
[tex]P \rightarrow M + N[/tex]
Reactants are the species present on the left side on an arrow in a chemical reaction equation.
On the other hand, products are the species which are present on the right side of an arrow in a chemical reaction equation.
Hence, in the given reaction equation P is the reactant. Whereas M and N are the products.
Thus, we can conclude that in the reaction:
a) The reactants are: P
b) The products are: M and N
why Hydroxide ion is less strong base than hydride ion
Answer:
The hydride ion,H−is a stronger base, so it will abstract a proton from the water. As the water will give protons, so water will work as an acid and an acid-base reaction will take place. Hydride ions get protons from water and form hydrogen gas and hydroxide ions.
Sodium hydride is the chemical compound with the empirical formula NaH. This alkali metal hydride is primarily used as a strong yet combustible base in organic synthesis. NaH is a saline (salt-like) hydride, composed of Na+ and H− ions, in contrast to molecular hydrides such as borane, methane, ammonia, and water.
Choose the substance with the highest viscosity. Choose the substance with the highest viscosity. CF4 C7H16 C2H4I2 HOCH2CH2CH2CH2OH (CH3CH2)2CO
Answer:
C2H4I2
Explanation:
Viscosity of a fluid has to do with the internal friction between the internal layers of the fluid.
Molecular weight is found to be related to the viscosity of a fluid even though the relationship may not be strictly linear.
However, the greater the molecular weight of a substance, the greater the viscosity of the material.
Since C2H4I2 has the greatest molecular weight (281.86 g/mol), it is also expected to display the greatest viscosity among all the compounds listed in the question.
describe how you would test your indicator to check that it works
Answer:
If the colour of the indicator changes blue when a base is there and when it changes to red or pink or scarlet when it is acid. Then we can say that the indicator is working
How much water, in grams, can be made from
2.44 × 10^24 hydrogen molecules?
Answer in units of g.
Answer:
[tex]m_{H_2O}=73.0gH_2O[/tex]
Explanation:
Hello there!
In this case, since the formation of water from hydrogen and oxygen is:
[tex]2H_2+O_2\rightarrow 2H_2O[/tex]
Whereas we find a 2:2 mole ratio of hydrogen to water. In such a way, by using the Avogadro's number, the aforementioned mole ratio and the molar mass of water (18.02 g/mol), we obtain the following grams of water product:
[tex]m_{H_2O}=2.44x10^{24}molec*\frac{1molH_2}{6.022x10^{23}molec}*\frac{2molH_2O}{2molH_2}*\frac{18.02gH_2O}{1molH_2O}\\\\ m_{H_2O}=73.0gH_2O[/tex]
Regards!
anuvia, the trade name for sitagliptin, was introduced in 2006 for the treatment of type 2 diabetes. In what type of orbital does the lone pair on each N atom reside.
Answer: hello your question is poorly written below is the complete question
answer:
For N1 : sp³ orbital
For N2: p orbital
For N3 : p orbital
For N4 : sp² orbital
For N5 : sp² orbital
Explanation:
Determining the type of orbital in which the lone pair on each N atom will reside.
From the configuration attached below we can determine the type of orbital and they are ;
For N1 : sp³ orbital
For N2: p orbital
For N3 : p orbital
For N4 : sp² orbital
For N5 : sp² orbital
The combination of isotopes of hydrogen characterized by emmision of radiation is believed to take place in the
a. sun
b. galaxy
c. moon
d. star
how many molecules are there in 75.0 grams of phosphorus trichloride plzz helpp
Answer:
Explanation:
55
Calculate the energy of the orange light emitted, per photon, by a neon sign with a frequency of 4.78 × 1014 Hz.
Answer:
Explanation:
[tex]E=h\nu=6.62606957 *10^{-34}\frac{Kg~m^2}{s}4.78*10^{14}\frac{1}{s}=316.7261*10^{-21}J[/tex]
aluminum chloride and bubbles of hydrogen gas are produced when metallic aluminum is placed in hydrochloride acid. what is a balanced equation for this reaction?
Answer:
AlCl3 + HCl ===> AlCl4 +H-
Aluminum metal reacts with oxygen gas in a combination reaction that forms a product that coat the metal preventing it from further oxidation. Which of the following is the correct balanced equation for the reaction?
a. Al(s) + 302(g) → 2903(s).
b. 2Al(s) + O2(g) → 2A10(s).
c. AI(s) + O2(g) → AIO (s).
d. 4Al(s) + 3O2(g) →2Al2O3.
e. 3Al(s) + O2 → Al3O2.
Answer:
d. 4 Al(s) + 3 O₂(g) → 2 Al₂O₃(s)
Explanation:
Aluminum metal reacts with oxygen gas in a combination reaction that forms a product that coats the metal preventing it from further oxidation: aluminum oxide. Aluminum is a cation with charge 3+ (Al³⁻) and oxide is an anion with charge 2- (O²⁻). Thus, the neutral compound aluminum oxide has the chemical formula Al₂O₃. The unbalanced chemical equation is:
Al(s) + O₂(g) → Al₂O₃(s)
We can balance using the trial and error method. First, we will balance O atoms by multiplying Al₂O₃ by 2 and O₂ by 3.
Al(s) + 3 O₂(g) → 2 Al₂O₃(s)
Finally, we get the balanced equation by multiplying Al by 4.
4 Al(s) + 3 O₂(g) → 2 Al₂O₃(s)
Is benzene a solute or solvent
Fire a single electron towards the hydrogen atom. Describe what happens in a step by step fashion. [N.B. - It may be helpful to utilize the Run in Slow Motion option for this part.]
Answer:
The electrons will be added by the hydrogen.
Explanation:
If we fire a single electron towards the hydrogen atom, the hydrogen atoms added the electron to its shell by applying force of attraction and becomes stable as well as non reactive in nature because the hydrogen attains the electronic configuration of helium which is a noble gas and have completed its outermost shell. The proton that is present in the nucleus attracts this electron and compel it to add in the electron.
Copper metal has a specific heat of 0.385 J/g.C. calculate the amount of heat required to raise the temperature of 22.8g of copper metal from 20.0C to 875°C
Answer:
7505.19 J
Explanation:
We'll begin by calculating the change in the temperature of copper. This can be obtained as follow:
Initial temperature (T₁) = 20 °C
Final temperature (T₂) = 875 °C
Change in temperature (ΔT) =?
ΔT = T₂ – T₁
ΔT = 875 – 20
ΔT = 855 °C
Finally, we shall determine the heat required. This can be obtained as follow:
Specific heat capacity (C) = 0.385 J/gºC
Change in temperature (ΔT) = 855 °C
Mass (M) = 22.8 g
Heat (Q) required =?
Q = MCΔT
Q = 22.8 × 0.385 × 855
Q = 7505.19 J
Thus, 7505.19 J of heat energy is required.
