Explain moment of inertia

Answers

Answer 1

Answer:

The moment of inertia is basically a physical quantity which describes how easy it is for a body to rotate itself around a given axis.

In easier wording: Moment of Inertia is a body and when it starts rotating or moving, it will keep doing so until we stop it by force.

Explanation:

For example, a car that is moving and active will continue to move even if you were to switch the engine off.


Related Questions

Explain the LWD process why is it important in drilling operations?

Answers

Answer:

Logging while drilling (LWD) is a technique of conveying well logging tools into the well borehole downhole as part of the bottom hole assembly (BHA). ... In these situations, the LWD measurement ensures that some measurement of the subsurface is captured in the event that wireline operations are not possible.

Explanation:

pls mark brainliest

Hydraulic fracturing is: Select one: a. a first step in storage of high-level radioactive waste b. a way of extracting natural gas shale formations c. a step in oil refining where oil is separated into different viscosities d. none of the above

Answers

The answer is B - a way of extracting natural gas shale formations.

Hydraulic fracturing is “a way of extracting natural gas shale formations.”

Shale and other types of "tight" rock, or impermeable rock formations that lock in oil and gas and complicate the production of fossil fuels, can be extracted of their natural gas or oil using the modern high-volume hydraulic fracturing process. Thus, option B is correct.

What are the factor involving in Hydraulic fracturing?

Shale gas is extracted through a procedure called hydraulic fracturing, also referred to as “fracking.” Due to the fact that shale reserves are often dispersed horizontally rather than vertically, deep holes are first drilled into the shale rock, then horizontal drilling is used to reach more of the gas.

A mixture of sand, chemicals, and water is pushed at high pressure down a borehole during hydraulic fracturing. The released gas can flow out of the rocks and back up the borehole because the water pressure causes cracks in the rock to widen, and the sand particles settle into the openings to keep them open.

Therefore, a way of extracting natural gas shale formations.

Learn more about Hydraulic fracturing here:

https://brainly.com/question/28559289

#SPJ2

Troy must keep track of the amount of refrigerant he uses from a 50-pound cylinder to ensure that accurate
records are kept. He used 13 pounds on a systein for Ms. Jones and 9 pounds on a system for a commercial
client. How many pounds should he have left in the cylinder?
tof
Troy should have
pounds of refrigerant left in the cylinder.
baon naid Thamar basic
محمود احمد مجد
12
اهداء ما در

Answers

Answer:

Amount of gas still in cylinder = 28 pound

Explanation:

Given:

Amount of gas in cylinder = 50 pound

Amount of gas used in Ms. Jones system = 13 pound

Amount of gas used in client system = 9 pound

Find:

Amount of gas still in cylinder

Computation:

Amount of gas still in cylinder = Amount of gas in cylinder - Amount of gas used in Ms. Jones system - Amount of gas used in client system

Amount of gas still in cylinder = 50 - 13 - 9

Amount of gas still in cylinder = 28 pound

True or false: You can create a network with two computers.



Answer
True

Answers

To create a computer network, you must have at least two computers. ... A protocol is a standard set of rules and procedures for the control of communications in a network. TRUE. Two computers using TCP/IP can communicate even if they are based on different hardware and software platforms. So your right :)

Hope this helps :)
True u must use two computers

A resistor has code 104 printed on it .What is the resistive value of this resistor ​

Answers

Answer:

X = 1 (1st digit in the code)

Y = 0 (2nd digit)

Z = 4 (3rd multiplier digit)

104 → 10 × 10^4 Ω

→ 10 × 10000Ω

→ 100 kΩ

resistors are marked 104, 105, 205, 751, and 754. The resistor marked with 104 should be 100kΩ (10x10^4), 105 would be 1MΩ (10x10^5), and 205 is 2MΩ (20x10^5). 751 is 750Ω (75x10^1), and 754 is 750kΩ (75x10^4).

Here we need to understand how a code in a resistor gives us information on the resistor. Here we will see that the code means that the resistance is 100,000 Ω.

When we use numbers, let's assume that we have 3 single-digit numbers abc.

So if the code in our resistor is abc, this will mean that the resistance of the resistor is:

ab×10^c Ω

Using this general rule we can see that if the code is 104, then the resistance will be:

r = 10×10^4 Ω

 = 100,000 Ω

Then we can conclude that the resistive value of this resistor is  100,000 Ω

If you want to learn more, you can read:

https://brainly.com/question/74415

Suppose we have 999 records of employees Emp1, Emp2, Emp5, Emp6 and so on up to Emp998 and Emp999 stored in a sequence. Hence, records are nothing but a row in the table. In the employee table, we want to insert new records Emp3 and Emp4 in the sequence, and once we have done insertion we need to update and retrieve the record efficiently to optimize the performance of a database by minimizing the access time when query is being executed.

Answers

The records in the table represents the employee ID of each employee. Assume the table name is EMPLOYEES and the field name of employee IDs is ID, the following SQL query inserts Emp3 and Emp4 into the employees table.

INSERT INTO EMPLOYEES (ID) values (Emp3), (Emp4)

The complete question requires that we list the pros and cons of solving the problem using Index sequential access method (ISAM).

The advantage of using ISAM is that priorities are given to the indices of the records being inserted. So, Emp3 and Emp4 will be inserted immediately after Emp2.

However, a major disadvantage of using ISAM is that it is very expensive to keep the indices in a sequential order;

See attachment for the illustration of Index sequential access method (ISAM).

Read more about Index sequential access method (ISAM) at:

https://brainly.com/question/4692093

The secondary coil of a step-up transformer provides the voltage that operates an electrostatic air filter. The turns ratio of the transformer is 41:1. The primary coil is plugged into a standard 120-V outlet. The current in the secondary coil is 1.2 x 10-3 A. Find the power consumed by the air filter.

Answers

Answer:

  5.9 watts

Explanation:

The secondary voltage is the primary voltage multiplied by the turns ratio:

  (120 V)(41) = 4920 V

The power is the product of voltage and current:

  (4920 V)(1.2·10^-3 A) = (4.92)(1.2) W = 5.904 W

The power consumed is about 5.9 watts.

Side milling cutter is an example of ______ milling cutter.

Answers

Answer:

special type

Explanation:

As per the classification of milling cutters. This cutter can handle deep and long open slots in a more comfortable manner, which increase the productivity.

Tech A says that the voltage regulator controls the strength of the rotor s magnetic field. Tech B says that the voltage regulator is installed between the output terminal of the alternator and the positive terminal of the battery. Who is correct?

Answers

Answer:

Voltage Regulator

Technician A is correct.

Explanation:

Technician B is not correct.  The voltage regulator is not installed between the output terminal of the alternator and the positive terminal of the battery as claimed by Technician B.  Technician A's opinion that the voltage regulator controls the strength of the rotor's magnetic field is correct.  The computer can also be used to control the output of the alternator by controlling the field current.

Why is logging done during drilling?

Answers

Answer:

Logging while drilling (LWD) is a technique of conveying well logging tools into the well borehole downhole as part of the bottom hole assembly (BHA). ... In these situations, the LWD measurement ensures that some measurement of the subsurface is captured in the event that wireline operations are not possible

If OSHA determines that an employer's response to a non-formal complaint is adequate, what options does the employee filing the non-formal complaint have?

Answers

Fill it out without telling ur employer as that may cause backlash and have an osha certified employee come check out ur work or job site

Select the correct statement(s) regarding IEEE 802.16 WiMAX BWA. a. WiMAX BWA describes both 4G Mobile WiMAX and fixed WiMax b. DSSS and CDMA are fundamental technologies used with WiMAX BWA c. OFDM is implemented to increase spectral efficiency and to improve noise performance d. all of the statements are correct

Answers

Answer:

d. all of the statements are correct.

Explanation:

WiMAX Broadband Wireless Access has the capacity to provide service up to 50 km for fixed stations. It has capacity of up to 15 km for mobile stations. WiMAX BWA describes both of 4G mobile WiMAX and fixed stations WiMAX. OFMD is used to increase spectral efficiency of WiMAX and to improve noise performance.

what is the term Self-induced EMF (Induction) ​

Answers

Self induction and Mutual induction

If the current through the coil changes, the flux through the coil changes and an emf is induced. Since the emf is induced in the coil due to its own field, it is called self–induced emf and the phenomenon is called self–induction.

Answer:

Self induced EMF is the electro-motive force that is generated due to change in flux in the coil caused by the change in current in the same coil.

What is the following diagram called?

Answers

Answer:

business

Explanation:

because shopping has great income

Answer:

is ur question right

Explanation:

is ur question right

is ur question right

4) A steel tape is placed around the earth at the equator when the temperature is 0 C. What will the clearance between the tape and the ground (assumed to be uniform) be if the temperature of the tape rises to 30 C. Neglect the expansion of the earth (the radius of the earth is 6.37 X 106 m)

Answers

Answer:

2102.1 m

Explanation:

Temperature at the equator = 0⁰

Radius of the earth = 6.37x10⁶

Required:

We how to find out what the clearance between tape and ground would be if temperature increases to 30 degrees.

Final temperature = ∆T = 303-273 = 30

S = 11x10^-6

The clearance R = Ro*S*∆T

=6.37x10⁶x 11x10^-6x30

= 2102.1m

Or 2.102 kilometers

Thank you

once scientist has asked a question conducted an investigation and analyzed the data his or hwr goalis to​

Answers

Answer:

hola

Explanation:

Explanation:

so its an question?..........

What is the following diagram called?

Answers

Answer:

flow chart

Explanation:

it's a flow chart right ? don't know the explanation cause I am not even sure I am right

Use a truth table to verify the first De Morgan law ¬(p ∧ q) ≡ ¬p ∨ ¬q.

Answers

Answer:

p q output ¬(p ∧ q)

0 0 1

0 1 1

1 0 1

0 0 0

p q output ¬p ∨ ¬q

0 0 1

0 1 1

1 0 1

0 0 0

Explanation:

We'll create two separate truth tables for both sides of the equation, and see if they match.

The expressions in the question use AND, OR and NOT operators.

The AND operation needs both inputs to be 1 to return a 1.The OR operation needs at least 1 of the inputs to be 1 to return a 1. The NOT operation takes a 1 and turns it into a 0, or takes a 0 and turns it into a 1.

Let's start with ¬(p ∧ q)

NOT (0 AND 0) = NOT (0) = 1NOT (0 AND 1) = NOT (0) = 1NOT (1 AND 0) = NOT (0) = 1NOT (1 AND 1) = NOT (1) = 0

Now let's move on to the second expression ¬p ∨ ¬q

NOT(0) OR NOT(0) = 1 OR 1 = 1NOT(0) OR NOT(1) = 1 OR 0 = 1NOT(1) OR NOT(0) = 0 OR 1 = 1NOT(0) OR NOT(0) = 0 OR 0 = 0

Therefore we can say the two expressions are equivalent.

Attached  the truth table to verify the first De Morgan's law ¬(p ∧ q) ≡ ¬p ∨ ¬q:

What is the explanation of the truth table?

As you can see from the attached truth table, the truth values for ¬(p ∧ q) and ¬p ∨ ¬q are the same for all combinations of p and q, confirming the validity of the first De Morgan's law.

De Morgan's law is a fundamental principle in propositional logic.

It states that the negation of a conjunction (AND) is equivalent to the disjunction (OR) of the negations of the individual propositions.

Learn more about truth table at:

https://brainly.com/question/28605215

#SPJ3

Unfiltered full wave rectifier with a 120 V 60 Hz input produces an output with a peak of 15V. When a capacitor-input filter and a 1k ohm load are connected the DC output voltage is 14V. What is... The value of the capacitor? The value of the peak to peak ripple voltage?

Answers

Answer:

[tex]V_{pp}=2V[/tex]

Explanation:

Source Voltage [tex]V= 120V[/tex]

Frequency [tex]f=60Hz[/tex]

Peak output voltage [tex]Vp=15V[/tex]

Peak Output Voltage with filter [tex]V_p'=14V[/tex]

Generally the equation for Peak to peak voltage is mathematically given by

[tex]V_p'=V_p-\frac{V_{pp}}{2}[/tex]

Therefore

[tex]V_{pp}=2(V_p-v_p')[/tex]

[tex]V_{pp}=2(15-14)[/tex]

[tex]V_{pp}=2V[/tex]

an atom that gained an electron is called​

Answers

Answer:

Hey mate......

Explanation:

This is ur answer.....

When an atom gains/loses an electron, the atom becomes charged, and is called an ion.

Hope it helps!

Brainliest pls!

Follow me :)

An atom that gained an electron is called an ION.

Future solution for air pollution in new zealand

Answers

Answer:

New Zealand may use some of these solutions to prevent air pollution

Explanation:

Using public transports.

Recycle and Reuse

No to plastic bags

Reduction of forest fires and smoking

Use of fans instead of Air Conditioner

Use filters for chimneys

Avoid usage of crackers

Hot air is to be cooled as it is forced to flow through the tubes exposed to atmospheric air. Fins are to be added in order to enhance heat transfer. Would you recommend attaching the fins inside or outside the tubes? Why? When would you recommend auaching fins both inside and outside the tubes?

Answers

Answer:

Fins should be attached outside the tube Fins can be attached on both sides when convection coefficient of air inside the tube is equal to the convection coefficient of atmospheric air outside the tube

Explanation:

The main function of the fins that are to be added is to ensure the speedy transfer of heat from the Hot air.

The fins should be attached outside the tube because the convection coefficient of air is higher inside the tube than the convection coefficient of the outside air ( atmospheric air ),  BUT

When convection coefficient of air inside the tube is equal to the atmospheric air outside the tube, it is recommended that the fins can be added on both sides of the tube ( i.e. in and outside the tube )

Compute the minimum length of vertical curve that will provide 220 m stopping sight distance for a design speed of 110 km/h at the intersection of a -3.50% grade and a +2.70% grade.

Answers

i have made notes and saved it as a pdf u can take it to answer question and make ur concept good

The minimum length of vertical curve that will provide 220 m stopping sight distance is; 458.8 m

We are given;

Stopping sight distance; S = 220 m

Design Speed; V = 110 km/h

Intersection grade 1; G1 = +2.7

Intersection Grade 2; G2 = -3.5

From the AASHTO Table attached, we can trace the value of the radius of vertical curvature for the given stopping sight distance and design speed.

From the table, at S = 220 m and V = 110 km/h, we can see that;

Radius of vertical curvature; K = 74

Now, the difference in grade given is;

A = G1 - G2

A = 2.7 - (-3.5)

A = 2.7 + 3.5

A = 6.2

Formula for the minimum length of vertical curve is;

L = KA

Thus;

L = 74 × 6.2

L = 458.8 m

Read more about stopping sight distance at; https://brainly.com/question/2087168

hỗ trợ mình với được không các bạn

Answers

Answer:

Explanation:

Be bop

The value of universal gas constant is same for all gases?
a) yes
b)No

Answers

Answer:

The answer of these questions is

Explanation:

b) NO

Race cars at the Indianapolis Speedway average speeds of 185 mi/h. After determining the altitude of Indianapolis, find the Mach number of these cars and estimate whether compressibility might affect their aerodynamics.

Answers

Answer:

- the Mach number is 0.24.

- Compressibility becomes effective when Mach number is greater than 0.3, the Mach number of the race cars is less than 0.3, hence, compressibility will not affect their aerodynamics.

Explanation:

Given the data in the question;

Average speed V = 185 miles per hour = ( 185 /2.237 ) m/s = 82.7 m/s

From Almanac, we can find that Indianapolis is at 220 m altitude.

So from table, at that altitude, the standard speed of sound will be 339.4 m/s .

Mach number of the race car will be;

Mach Number = Velocity / sound speed

we substitute

Mach Number = ( 82.7 m/s ) / ( 339.4 m/s )

Mach Number = 0.24

Therefore the Mach number is 0.24.

We know that, compressibility becomes effective when the Mach number is greater than 0.3.

Since the Mach number of the race cars is less than 0.3, compressibility will not affect their aerodynamics.

 

A binary system of species 1 and 2 consists of vapor and liquid phases in equilibrium
at temperature T. The overall mole fraction of species 1 in the system is z1 = 0.65. At
temperature T, lnγ1 = 0.67 x2
2; lnγ2 = 0.67 x1
2; P1
sat = 32.27 kPa; and P2
sat = 73.14 kPa.
Assuming the validity of Eq. (13.19),
Final PDF to printer
13.10. Problems 511
smi96529_ch13_450-523.indd 511 01/06/17 03:27 PM
(a) Over what range of pressures can this system exist as two phases at the given T and z1?
(b) For a liquid-phase mole fraction x1 = 0.75, what is the pressure P and what molar
fraction of the system is vapor?
(c) Show whether or not the system exhibits an azeotrope

Answers

The answer in photo
Please don't forget put heart ♥️

Solve using Matlab the problems:

One using the permutation of n objects formula

One using the permutation of r objects out of n objects

You can pick these problems from the textbook or you can make up your own questions.


Help me pleaseeeee

Answers

Answer:

Explanation:

% Clears variables and screen

clear; clc

% Asks user for input

n = input('Total number of objects: ');

r = input('Size of subgroup: ');

% Computes and displays permutation according to basic formulas

p = 1;

for i = n - r + 1 : n

   p = p*i;

end

str1 = [num2str(p) ' permutations'];

disp(str1)

% Computes and displays combinations according to basic formulas

str2 = [num2str(p/factorial(r)) ' combinations'];

disp(str2)

=================================================================================

Example: check

How many permutations and combinations can be made of the 15 alphabets, taking four at a time?

The answer is:

32760 permutations

1365 combinations

==================================================================================

Question in Statistics and Probability 2

Petrol samples were taken at three different stations along a national highway to determine whether the octane rating varied from one station to another. Six petrol specimens of the same category were randomly selected at each station in different days. We are interested to know if there is sufficient evidence to indicate a difference in the mean octane rating at the different stations.
 
State the Null and the Alternative Hypotheses. 

Answers

I have this questions For a confidence level of 80% with a sample size of 21, find the critical t value answer key then u can help?
Other Questions
pete walks at a rate of 4.0 miles per hour for 30 minutes. How far did he walk? Today's English mainly comes from 1) French settlers 2) Hispanic settlers 3) British settlers 4) German settlers how to write informal letter? 16: The temperature yesterday at noon was 68.5 degrees. Today at noonit was 59.9 degrees. What was the difference in temperature?O A. 8.4 degreesOB. 8.5 degreesC. 8.6 degreesO D. 8.7 degrees HELP this stem and leaf plot represents test scores of students in a math class if two test score 68 and 75 are added to the data which statement will be true Decompose -6x/(x+2)(x+8) into partial fractions. X/6 - y/3 = 1 please explain in detail! The ratio of the volumes of two similar solid polyhedra is equal to the square root of the ratio between their edges. True or False? HELP QUICK PLSSSSS If an investor has a choice of investing money at 6% compounded daily or 6.025% compounded quarterly which one is best How many hydrogen atoms are there in the molecule H2S04?O A. 1B. 3C. 4.O D. 2 A bag contains 3 red, 5 blue, and 4 white marbles. If a marble is drawn from the bag, not replaced, and another is drawn, what is the probability of selecting a white and then blue marble? functions of insulin Is the relationship shown by the data linear? If so, model the data with an equation. For each sentence, fill in each blank with the simple past or simple present form of the verb inparentheses.1. More than 50 years after President Kennedy______(sign) the Equal Pay Act, thegap between salaries for men and women________(remain) a problem today.2. Last year's study__________(find) that in the last decade the pay gap_________(become) greater the longer a person was in the workforce.3. The United States is one of few countries in the developed world that currently________(use) the death penalty. Mexico, its neighbor to the south,_______(end) the death penalty in 2005.4. During the 1950s and 1960s, Martin Luther King, Jr.,______(lead) the civil rightsmovement in the United States. Civil rights______(include) the right to vote, theright to a fair trial, and the right to an education.5. Fifteen nations___________(make up) the UN Security Council. The Security Council____(hold) its first session on January 17, 1946, in London. The Canterbury Tales were mostly written in ________ form. - prose - poetry - sonnet - eulogy Triangle XYZ is isosceles. The measure of the vertex angle, Y, is twice the measure of a base angle. What is true about triangle XYZ? Select three options. (06.01)Write the following expression in exponential form:1.6 1.6 1.6 1.6 41.6 1.64 1.6 4 1.6 + 4 Select all the words that are written correctly.JaponsFrancesoEspaoloJapnFrancsEspaol Examples of people who weren't afraid to take help to succeed The graph of a line is shown below. What is the equation of the line, in slope-intercept form, that is parallel to this line and has a y-intercept of 1?