Explanation:
A circuit breaker is an electrical switch designed to protect an electrical circuit from damage caused by overcurrent/overload or short circuit. Its basic function is to interrupt current flow after protective relays detect a fault.
Circuit breakers have been designed to detect when there is a fault in the electricity, so it will “trip” and shut down electrical flow. ... This detection is key to preventing surges of electricity that travel to appliances or other outlets, which can cause them to break down
Help me with my physics, please
A 31 kg block is initially at rest on a horizontal surface. A horizontal force of 83 N is required to set the block in motion. After it is in motion, a horizontal force of 55 N i required to keep it moving with constant speed. From this information, find the coefficients of static and kinetic friction
Answer:
The static and kinetic coefficients of friction are 0.273 and 0.181, respectively.
Explanation:
By Newton's Laws of Motion and definition of maximum friction force, we derive the following two formulas for the static and kinetic coefficients of friction:
[tex]\mu_{s} = \frac{f_{s}}{m\cdot g}[/tex] (1)
[tex]\mu_{k} = \frac{f_{k}}{m\cdot g}[/tex] (2)
Where:
[tex]\mu_{s}[/tex] - Static coefficient of friction, no unit.
[tex]\mu_{k}[/tex] - Kinetic coefficient of friction, no unit.
[tex]f_{s}[/tex] - Static friction force, in newtons.
[tex]f_{k}[/tex] - Kinetic friction force, in newtons.
[tex]m[/tex] - Mass, in kilograms.
[tex]g[/tex] - Gravitational constant, in meters per square second.
If we know that [tex]f_{s} = 83\,N[/tex], [tex]f_{k} = 55\,N[/tex], [tex]m = 31\,kg[/tex] and [tex]g = 9.807\,\frac{m}{s^{2}}[/tex], then the coefficients of friction are, respectively:
[tex]\mu_{s} = \frac{83\,N}{(31\,kg)\cdot \left(9.807\,\frac{m}{s^{2}} \right)}[/tex]
[tex]\mu_{s} = 0.273[/tex]
[tex]\mu_{k} = \frac{55\,N}{(31\,kg)\cdot \left(9.807\,\frac{m}{s^{2}} \right)}[/tex]
[tex]\mu_{k} = 0.181[/tex]
The static and kinetic coefficients of friction are 0.273 and 0.181, respectively.
Cell phone conversations are transmitted by high-frequency radio waves. Suppose the signal has wavelength 35 cm while traveling through air. What are the
(a) frequency and
(b) wavelength as the signal travels through 3-mm-thick window glass into your room?
Answer:
(a) 8.57 x 10^8 Hz
(b) 23.3 cm
Explanation:
Wavelength = 35 cm = 0.35 m
speed =3 x10^8 m/s
Let the frequency is f.
(a) The relation is
speed = frequency x wavelength
3 x 10^8 = 0.35 x f
f = 8.57 x 10^8 Hz
(b) refractive index of glass is 1.5
The relation for the refractive index and the wavelength is
wavelength in glass= wavelength in air/ refractive index.
Wavelength in glass= 35/1.5 = 23.3 cm
ACCORDING TO NEWTON'S THIRD LAW EVERY ACTION HAS EQUAL AND OPPOSITE REACTION BUT THEN WHY DON'T WE FLY WHEN WE FART??
Answer:
Your fart only has so much force, not nearly enough to launch you into oblivion. Your fart and you still exert a force onto each other, so I guess, hypothetically, you could fly if you really, really try hard enough. Just make sure you don't try too hard and prolapse as a result :)
Assume that I = E/(R + r), prove that 1/1 = R/E + r/E
[tex]\implies {\blue {\boxed {\boxed {\purple {\sf { \frac{1}{I} = \frac{R}{E} + \frac{r}{E} }}}}}}[/tex]
[tex]\large\mathfrak{{\pmb{\underline{\orange{Step-by-step\:explanation}}{\orange{:}}}}}[/tex]
[tex]I = \frac{ E}{ R + r} \\[/tex]
[tex] ➺\:\frac{I}{1} = \frac{E}{R + r} \\[/tex]
Since [tex]\frac{a}{b} = \frac{c}{d} [/tex] can be written as [tex]ad = bc[/tex], we have
[tex]➺ \: I \: (R + r) = E \times 1[/tex]
[tex]➺ \: \frac{1}{I} = \frac{R + r}{E} \\ [/tex]
[tex]➺ \: \frac{1}{I} = \frac{R}{E} + \frac{r}{E} \\ [/tex]
[tex]\boxed{ Hence\:proved. }[/tex]
[tex]\red{\large\qquad \qquad \underline{ \pmb{{ \mathbb{ \maltese \: \: Mystique35ヅ}}}}}[/tex]
What best describes a societal law
Answer:
Societal laws are based on the behavior and conduct made by society or government.hope it helps.stay safe healthy and happy.An electron in a hydrogen atom is in a p state. Which of the following statements is true?
a.
The electron’s wavefunction has at least one node (i.e., at least one place in space where it goes to zero).
b.
The electron has an energy of -13.6 eV.
c.
The electron has a total angular momentum of ħ.
d.
The electron has a z-component of angular momentum equal to sqrt(2)* ħ.
Answer:
The electron’s wavefunction has at least one node (i.e., at least one place in space where it goes to zero).
Explanation:
We know that the p-orbitals have nodes. A node is a region where the probability of finding an electron goes down to zero.
P orbitals are oriented along the x,y,z Cartesian axes and are known to have angular nodes along the axes.
Hence, if an electron in a hydrogen atom is in a p state, the electron’s wavefunction has at least one node
what is time taken by radio wave to go and return back from communication satellite to earth??
Answer:
Radio waves are used to carry satellite signals. These waves travel at 300,000 km/s (the speed of light). This means that a signal sent to a satellite 38,000 km away takes 0.13 s to reach the satellite and another 0.13 s for the return signal to be received back on Earth.
Explanation:
hope it help
Based on the information in the table, what
is the acceleration of this object?
t(s) v(m/s)
0.0
9.0
1.0
4.0
2.0
-1.0
3.0
-6.0
A. -5.0 m/s2
B. -2.0 m/s2
C. 4.0 m/s2
D. 0.0 m/s2
Answer:
Option A. –5 m/s²
Explanation:
From the question given above, the following data were obtained:
Initial velocity (v₁) = 9 m/s
Initial time (t₁) = 0 s
Final velocity (v₂) = –6 m/s
Final time (t₂) = 3 s
Acceleration (a) =?
Next, we shall determine the change in the velocity and time. This can be obtained as follow:
For velocity:
Initial velocity (v₁) = 9 m/s
Final velocity (v₂) = –6 m/s
Change in velocity (Δv) =?
ΔV = v₂ – v₁
ΔV = –6 – 9
ΔV = –15 m/s
For time:
Initial time (t₁) = 0 s
Final time (t₂) = 3 s
Change in time (Δt) =?
Δt = t₂ – t₁
Δt = 3 – 0
Δt = 3 s
Finally, we shall determine the acceleration of the object. This can be obtained as follow:
Change in velocity (Δv) = –15 m/s
Change in time (Δt) = 3 s
Acceleration (a) =?
a = Δv / Δt
a = –15 / 3
a = –5 m/s²
Thus, the acceleration of the object is
–5 m/s².
Two spheres are rolling without slipping on a horizontal floor. They are made of different materials, but each has mass 5.00 kg and radius 0.120 m. For each the translational speed of the center of mass is 4.00 m/s. Sphere A is a uniform solid sphere and sphere B is a thin-walled, hollow sphere. Part B How much work, in joules, must be done on the solid sphere to bring it to rest? Express your answer in joules. VO AE4D ? J WA Request Answer Submit Part C How much work, in joules, must be done on the hollow sphere to bring it to rest? Express your answer in joules. Wa Request
Answer:
Explanation:
Moment of inertia of solid sphere = 2/5 m R²
m is mass and R is radius of sphere.
Putting the values
Moment of inertia of solid sphere I₁
Moment of inertia of hollow sphere I₂
Kinetic energy of solid sphere ( both linear and rotational )
= 1/2 ( m v² + I₁ ω²) [ ω is angular velocity of rotation ]
= 1/2 ( m v² + 2/5 m R² ω²)
= 1/2 ( m v² + 2/5 m v²)
=1/2 x 7 / 5 m v²
= 0.7 x 5 x 4² = 56 J .
This will be equal to work to be done to stop it.
Kinetic energy of hollow sphere ( both linear and rotational )
= 1/2 ( m v² + I₂ ω²) [ ω is angular velocity of rotation ]
= 1/2 ( m v² + 2/3 m R² ω²)
= 1/2 ( m v² + 2/3 m v²)
=1/2 x 5 / 3 m v²
= 0.833 x 5 x 4² = 66.64 J .
This will be equal to work to be done to stop it.
how do you calculate voltage drop
Answer:
Multiply current in amperes by the length of the circuit in feet to get ampere-feet. Circuit length is the distance from the point of origin to the load end of the circuit.
Divide by 100.
Multiply by proper voltage drop value in tables. The result is voltage drop.
Explanation:
The following two waves are sent in opposite directions on a horizontal string so as to create a standing wave in a vertical plane: y1(x, t) = (8.20 mm) sin(4.00πx - 430πt) y2(x, t) = (8.20 mm) sin(4.00πx + 430πt), with x in meters and t in seconds. An antinode is located at point A. In the time interval that point takes to move from maximum upward displacement to maximum downward displacement, how far does each wave move along the string?
Answer:
Explanation:
From the information given:
The angular frequency ω = 430 π rad/s
The wavenumber k = 4.00π which can be expressed by the equation:
k = ω/v
∴
4.00 = 430 /v
v = 430/4.00
v = 107.5 m/s
Similarly: k = ω/v = 2πf/fλ
We can say that:
k = 2π/λ
4.00 π = 2π/λ
wavelength λ = 2π/4.00 π
wavelength λ = 0.5 m
frequency of the wave can now be calculated by using the formula:
f = v/λ
f = 107.5/0.5
f = 215 Hz
Also, the Period(T) = 1/215 secs
The time at which particle proceeds from point A to its maximum upward displacement and to its maximum downward displacement can be computed as t = T/2;
Thus, the distance(x) covered by each wave during this time interval(T/2) will be:
x = v * t
x = v * T/2
x = λ/2
x = 0.5/2
x = 0.25 m
vector A has a magnitude of 8 unit make an angle of 45° with posetive x axis vector B also has the same magnitude of 8 unit along negative x axis find the magnitude of A+B?
Answer:
45 × 8 units = A + B as formular
~~~~~NEED HELP ASAP~~~~~
A point on a rotating wheel (thin loop) having a constant angular velocityy of 300 rev/min, the wheel has a radius of 1.5m and a mass of 30kg. (I = mr^2)
a.) Determine the linear regression
b.) At this given angular velocity, what is the rotational kinetic energy?
Answer:
Centripetal Acceleration 18.75 m/s^2, Rotational Kinetic Energy 843.75 J
Explanation:
a Linear acceleration (we cant find tangential acceleration with the givens so we will find centripetal)
a= ω^2*r
ω= 300rev/min
convert into rev/s
300/60= 5rev/s
a= 18.75m/s^2
b) use Krot= 1/2 Iω^2
plug in gives
1/2(30*2.25)(25)= 843.75 J
The relation of mass m, angular velocity o and radius of the circular path r of an object with the centripetal force is-
a. F = m²wr
b. F = mwr²
c. F = mw²r
d. F = mwr.
Answer:
Correct option not indicated
Explanation:
There are few mistakes in the question. The angular velocity ought to have been denoted with "ω" and not "o" (as also suggested in the options).
The formula to calculate a centripetal force (F) is
F = mv²/r
Where m is mass, v is velocity and r is radius
where
While the formula to calculate a centrifugal force (F) is
F = mω²r
where m is mass, ω is angular velocity and r is radius of the circular path.
From the above, it can be denoted that the relationship been referred to in the question is that of a centrifugal force and not centripetal force, thus the correct option should be C.
NOTE: Centripetal force is the force required to keep an object moving in a circular path/motion and acts inward towards the centre of rotation while centrifugal force is the force felt by an object in circular motion which acts outward away from the centre of rotation.
d. On the afternoon of January 15, 1919, an unusually warm day in Boston, a 17.7-m-high, 27.4-m-diameter cylindrical metal tank used for storing molasses ruptured. Molasses flooded into the streets in a 5-m-deep stream, killing pedestrians and horses and knocking down buildings. The molasses had a density of 1600 kg>m3 . If the tank was full before the accident, what was the total outward force the molasses exerted on its sides
Answer:
F = 1.638 x 10⁸ N = 163.8 MN
Explanation:
The total force exerted by the molasses is given as:
F = PA
where,
F = Force exerted by the molasses = ?
P = Pressure = ρgh
ρ = density of molasses = 1600 kg/m³
g = acceleration due to gravity = 9.81 m/s²
h = height of tank = 17.7 m
A = cross-sectional area of tank = πr²
r = radius of tank = 27.4 m/2 = 13.7 m
Therefore,
[tex]F = \rho ghA = \rho gh(\pi r^2)\\\\F = (1600\ kg/m^3)(9.81\ m/s^2)(17.7\ m)(\pi)(13.7\ m)^2[/tex]
F = 1.638 x 10⁸ N = 163.8 MN
During a practice shot put throw, the 7.9-kg shot left world champion C. J. Hunter's hand at speed 16 m/s. While making the throw, his hand pushed the shot a distance of 1.4 m. Assume the acceleration was constant during the throw.
Required:
a. Determine the acceleration of the shot.
b. Determine the time it takes to accelerate the shot.
c, Determine the horizontal component of the force exerted on the shot by hand.
Answer:
a) a = 91.4 m / s², b) t = 0.175 s, c)
Explanation:
a) This is a kinematics exercise
v² = vox ² + 2a (x-xo)
a = v² - 0/2 (x-0)
let's calculate
a = 16² / 2 1.4
a = 91.4 m / s²
b) the shooting time
v = vox + a t
t = v-vox / a
t = 16 / 91.4
t = 0.175 s
c) let's use Newton's second law
F = ma
F = 7.9 91.4
F = 733 N
a vessel with mass 10kg intially moving withthe velocicity 12m s along the x axis explodes into three exactly identical pieces Just after the explosion one piece moves with speed 10 m s along the x axis and asecond piece moves with speed 10 m s along the y axis What iis the magnitude of the component of velocity of the third piece along the y axiss
Answer:
Explanation:
Apply law of conservation of momentum along y-axis.
Initially there was no momentum along y-axis. So there will be nil momentum along y-axis again finally.
Let the mass of each piece after breaking be m .
Momentum of piece moving along positive y-axis
= m x 10 = 10m .
Let the component of velocity of third piece along y-axis be v .
Its momentum along the same direction = m v .
Total momentum along y -axis = 10 m + m v
According to law of conservation of momentum
10 m + mv = 0
v = - 10 m/s .
Component of velocity of the third piece along y-axis will be - 10 m/s .
In other words it will be along negative y-axis with speed of 10 m/s.
A body of mass 2kg is released from from a point 100m above the ground level. calculate kinetic energy 80m from the point of released.
Answer:
1568J
Explanation:
Since the problem states 80 m from the point of drop, the height relative to the ground will be 100-80=20m.
Use conservation of Energy
ΔUg+ΔKE=0
ΔUg= mgΔh=2*9.8*(20-100)=-1568J
ΔKE-1568J=0
ΔKE=1568J
since KEi= 0 since the object is at rest 100m up, the kinetic energy 20meters above the ground is 1568J
A charge Q exerts a 1.2 N force on another charge q. If the distance between the charges is doubled, what is the magnitude of the force exerted on Q by q
Answer:
0.3 N
Explanation:
Electromagnetic force is F= Kq1q2/r^2, where r is the distance between charges. If r is doubled then the force will be 1/4F which is 0.3 N.
The magnitude of the force exerted on Q by q when the distance between them is doubled is 0.3 N
Coulomb's law equationF = Kq₁q₂ / r²
Where
F is the force of attraction K is the electrical constant q₁ and q₂ are two point charges r is the distance apart Data obtained from the question Initial distance apart (r₁) = rInitial force (F₁) = 1.2 NFinal distance apart (r₂) = 2rFinal force (F₂) =? How to determine the final forceFrom Coulomb's law,
F = Kq₁q₂ / r²
Cross multiply
Fr² = Kq₁q₂
Kq₁q₂ = constant
F₁r₁² = F₂r₂²
With the above formula, we can obtain the final force as follow:
F₁r₁² = F₂r₂²
1.2 × r² = F₂ × (2r)²
1.2r² = F₂ × 4r²
Divide both side by 4r²
F₂ = 1.2r² / 4r²
F₂ = 0.3 N
Learn more about Coulomb's law:
https://brainly.com/question/506926
Name the electrolyte in the chemical method of generating electricity
A body starts from rest and accelerates uniformly at 5m/s. Calculate the time taken by the body to cover a distance of 1km
Answer:
20 seconds
Explanation:
We are given 2 givens in the first statement
v0=0 and a=5
And we are trying to find time needed to cover 1km or 1000m.
So we use
x-x0=v0t+1/2at²
Plug in givens
1000=0+2.5t²
solve for t
t²=400
t=20s
It takes the elevator in a skyscraper 4.0 s to reach its cruising speed of 10 m/s. A 60 kg passenger gets aboard on the ground floor.
1. What is the passenger's apparent weight before the elevator starts moving?
2. What is the passenger's apparent weight whilethe elevator is speeding up?
3. What is the passenger's apparent weight afterthe elevator reaches its cruising speed?
Answer:
1. 588 N
2. 738 N
3. 588 N
Explanation:
time, t = 4 s
initial velocity, u = 0
final velocity, v = 10 m/s
mass, m= 60 kg
1.
Weight of passenger before starts
W =m g = 60 x 9.8 = 588 N
2.
When the elevator is speeding up
v = u + a t
10 = 0 + a x 4
a = 2.5 m/s2
Now the weight is
W' = m (a + g) = 60 (9.8 + 2.5) = 738 N
3.
When he reaches the cruising speed, the weight is
W = 588 N
Suppose the pucks start spinning after the collision, whereas they were not before. Will this affect your momentum conservation results
Answer:
No, it will not affect the results.
Explanation:
For elastic collisions in an isolated system, when a collision occurs, it means that the systems objects total momentum will be conserved under the condition that there will be no net external forces that act upon the objects.
What that means is that if the pucks start spinning after the collision, we are not told that there was any net external force acting on the puck and thus momentum will be conserved because momentum before collision will be equal to the momentum after the collision.
a. Give an example of the conversion of light energy to electrical energy.
b. Give an example of chemical energy converting to heat energy.
c. Give an example of mechanical energy converting to heat energy.
Explanation:
a) photovoltaic cell is a semiconductor device and it converts light energy to electrical energy
b) burning of coal converts chemical energy to heat energy
c) rubbing of both hands against each other converts mechanical to heat energy
Answer:
a. solar cells
b.coal,wood,petroleum
c.rubbing ours palms
A charge of 0.20uC is 30cm from a point charge of 3.0uC in vacuum. what work is required to bring the 0.2uC charge 18cm closer to the 3.0uC charge?
Answer:
The correct answer is "[tex]4.49\times 10^{10} \ joules[/tex]".
Explanation:
According to the question,
The work will be:
⇒ [tex]Work=-\frac{kQq}{R}[/tex]
[tex]=-\frac{1}{4 \pi \varepsilon \times (18-30)\times 3\times 0.2}[/tex]
[tex]=-\frac{1}{4 \pi \varepsilon \times (-12)\times 3\times 0.2}[/tex]
[tex]=\frac{0.3978}{\varepsilon }[/tex]
[tex]=4.49\times 10^{10} \ joules[/tex]
Thus the above is the correct answer.
We have that the workdone is mathematically given as
W=4.49*10e10 J
From the question we are told
A charge of 0.20uC is 30cm from a point charge of 3.0uC in vacuum. what work is required to bring the 0.2uC charge 18cm closer to the 3.0uC charge?WorkdoneGenerally the equation for the workdone is mathematically given as
W=-kQq/R
Therefore
0.3978/ε0 =-1/(4πε0*(18-30)*3*0.2
Hence
W=4.49*10e10 JFor more information on Charge visit
https://brainly.com/question/9383604
The outer surface of a spacecraft in space has an emissivity of 0.44 and a solar absorptivity of 0.3. If solar radiation is incident on the spacecraft at a rate of 950 W/m2, determine the surface temperature of the spacecraft when the radiation emitted equals the solar energy absorbed.
Answer:
[tex]T=326.928K[/tex]
Explanation:
From the question we are told that:
Emissivity [tex]e=0.44[/tex]
Absorptivity [tex]\alpha =0.3[/tex]
Rate of solar Radiation [tex]R=0.3[/tex]
Generally the equation for Surface absorbed energy is mathematically given by
[tex]E=\alpha R[/tex]
[tex]E=0.3*950[/tex]
[tex]E=285W/m^2[/tex]
Generally the equation for Emitted Radiation is mathematically given by
[tex]\mu=e(\sigmaT^4)[/tex]
Where
T=Temperature
[tex]\sigma=5.67*10^8Wm^{-2}K_{-4}[/tex]
Therefore
[tex]\alpha*E=e \sigma T^4[/tex]
[tex]0.3*(950)=0.44(5.67*10^-8)T^4[/tex]
[tex]T=326.928K[/tex]
PLZ help asap :-/
............................
Explanation:
[16][tex]\underline{\boxed{\large{\bf{Option \; A!! }}}} [/tex]
Here,
[tex]\rm { R_1} [/tex] = 2Ω[tex]\rm { R_2} [/tex] = 2Ω[tex]\rm { R_3} [/tex] = 2Ω[tex]\rm { R_4} [/tex] = 2ΩWe have to find the equivalent resistance of the circuit.
Here, [tex]\rm { R_1} [/tex] and [tex]\rm { R_2} [/tex] are connected in series, so their combined resistance will be given by,
[tex]\longrightarrow \rm { R_{(1,2)} = R_1 + R_2} \\ [/tex]
[tex]\longrightarrow \rm { R_{(1,2)} = (2 + 2) \; Omega} \\ [/tex]
[tex]\longrightarrow \rm { R_{(1,2)} = 4 \; Omega} \\ [/tex]
Now, the combined resistance of [tex]\rm { R_1} [/tex] and [tex]\rm { R_2} [/tex] is connected in parallel combination with [tex]\rm { R_3} [/tex], so their combined resistance will be given by,
[tex]\longrightarrow \rm {\dfrac{1}{ R_{(1,2,3)}} = \dfrac{1}{R_{(1,2)}} + \dfrac{1}{R_3} } \\ [/tex]
[tex]\longrightarrow \rm {\dfrac{1}{ R_{(1,2,3)}} = \Bigg ( \dfrac{1}{4} + \dfrac{1}{2} \Bigg ) \;\Omega} \\ [/tex]
[tex]\longrightarrow \rm {\dfrac{1}{ R_{(1,2,3)}} = \Bigg ( \dfrac{1 + 2}{4} \Bigg ) \;\Omega} \\ [/tex]
[tex]\longrightarrow \rm {\dfrac{1}{ R_{(1,2,3)}} = \Bigg ( \dfrac{3}{4} \Bigg ) \;\Omega} \\ [/tex]
Reciprocating both sides,
[tex]\longrightarrow \rm {R_{(1,2,3)}= \dfrac{4}{3} \;\Omega} \\ [/tex]
Now, the combined resistance of [tex]\rm { R_1} [/tex], [tex]\rm { R_2} [/tex] and [tex]\rm { R_3} [/tex] is connected in series combination with [tex]\rm { R_4} [/tex]. So, equivalent resistance will be given by,
[tex]\longrightarrow \rm {R_{(1,2,3,4)}= R_{(1,2,3)} + R_4} \\ [/tex]
[tex]\longrightarrow \rm {R_{(1,2,3,4)}= \Bigg ( \dfrac{4}{3} + 2 \Bigg ) \; \Omega} \\ [/tex]
[tex]\longrightarrow \rm {R_{(1,2,3,4)}= \Bigg ( \dfrac{4 + 6}{3} \Bigg ) \; \Omega} \\ [/tex]
[tex]\longrightarrow \rm {R_{(1,2,3,4)}= \Bigg ( \dfrac{10}{3} \Bigg ) \; \Omega} \\ [/tex]
[tex]\longrightarrow \bf {R_{(1,2,3,4)}= 3.33 \; \Omega} \\ [/tex]
Henceforth, Option A is correct.
_________________________________[17][tex]\underline{\boxed{\large{\bf{Option \; B!! }}}} [/tex]
Here, we have to find the amount of flow of current in the circuit. By using ohm's law,
[tex] \longrightarrow [/tex] V = IR
[tex] \longrightarrow [/tex] 3 = I × 3.33
[tex] \longrightarrow [/tex] 3 ÷ 3.33 = I
[tex] \longrightarrow [/tex] 0.90 Ampere = I
Henceforth, Option B is correct.
____________________________[tex] \tt \purple{Hope \; it \; helps \; you, Army! \heartsuit } \\ [/tex]
A 100-W light bulb is left on for 20.0 hours. Over this period of time, how much energy did the bulb use?
Answer:
Power = Energy/time
Energy = Power xtime.
Time= 20hrs
Power = 100Watt =0.1Kw
Energy = 0.1 x 20 = 2Kwhr.
This Answer is in Kilowatt-hour ...
If the one given to you is in Joules
You'd have to Change your time to seconds
Then Multiply it by the power of 100Watts.
1.- Que distancia recorrió una carga de 2,5x10-6 coul, generando así un campo eléctrico de 55new/coul.
Answer:
r = 20.22 m
Explanation:
Given that,
Charge,[tex]q=2.5\times 10^{-6}\ C[/tex]
Electric field, [tex]E=55\ N/C[/tex]
We need to find the distance. We know that, the electric field a distance r is as follows :
[tex]E=\dfrac{kq}{r^2}\\\\r=\sqrt{\dfrac{kq}{E}}\\\\r=\sqrt{\dfrac{9\times 10^9\times 2.5\times 10^{-6}}{55}}\\\\r=20.22\ m[/tex]
So, the required distance is 20.22 m.
