Five wheels are connected as shown in the figure. Find the velocity of the block “Q”, if it is known that: RA= 5 [m], RB= 10 [m], RD= 6 [m], RE=12 [m]. ​

Five Wheels Are Connected As Shown In The Figure. Find The Velocity Of The Block Q, If It Is Known That:

Answers

Answer 1

Answer:

-5 m/s

Explanation:

The linear velocity of B is equal and opposite the linear velocity of E.

vB = -vE

vB = -ωE rE

10 m/s = -ωE (12 m)

ωE = -0.833 rad/s

The angular velocity of E is the same as the angular velocity of D.

ωE = ωD

ωD = -0.833 rad/s

The linear velocity of Q is the same as the linear velocity of D.

vQ = vD

vQ = ωD rD

vQ = (-0.833 rad/s) (6 m)

vQ = -5 m/s


Related Questions

When an ideal gas undergoes a slow isothermal expansion, A : the work done by the environment is the same as the energy absorbed as heat. B : the increase in internal energy is the same as the work done by the environment. C : the work done by the gas is the same as the energy absorbed as heat. D : the increase in internal energy is the same as the heat absorbed. E : the increase in internal energy is the same as the work done by the gas.

Answers

Explanation:

When an ideal gas undergoes a slow isothermal expansion, following phenomenon occur

1. Work done bu the gas = Energy absorbed as heat.

2. Work done by environment = Energy absorbed as heat.

3. Increase in internal energy= Heat absorbed= work done by gas = work done by environment.

Hence all option are correct.

Increase in internal energy is equal to the heat absorbed or work done by gas or environment. All the statements are correct.

If an ideal gas undergoes a slow isothermal expansion,

Work done by the gas is directly proportional energy absorbed as heat.

Work done by environment  is directly proportional energy  absorbed as heat.

Increase in internal energy is equal to the heat absorbed or work done by gas or environment.

To know more about the Ideal gas,

https://brainly.com/question/8711877

A long, thin solenoid has 450 turns per meter and a radius of 1.17 cm. The current in the solenoid is increasing at a uniform rate did. The magnitude of the induced electric field at a point which is near the center of the solenoid and a distance of 3.45 cm from its axis is 8.20×10−6 V/m.
Calculate di/dt
di/dt = _________.

Answers

Answer:

[tex]\frac{di}{dt} = 7.31 \ A/s[/tex]

Explanation:

From the question we are told that  

     The  number of turns is  [tex]N = 450 \ turns[/tex]

      The  radius is  [tex]r = 1.17 \ cm = 0.0117 \ m[/tex]

       The  position from the center consider is  x =  3.45 cm  =  0.0345 m

       The  induced emf is  [tex]e = 8.20 *10^{-6} \ V/m[/tex]

Generally according to Gauss law

        [tex]\int\limits { e } \, dl = \mu_o * N * \frac{di}{dt } * A[/tex]

=>    [tex]e * 2\pi x = \mu_o * N * \frac{d i }{dt } * A[/tex]

Where A is the  cross-sectional area of the solenoid which is mathematically represented as

                [tex]A = \pi r ^2[/tex]

=>      [tex]e * 2\pi x = \mu_o * N * \frac{d i }{dt } * \pi r^2[/tex]

=>       [tex]\frac{di}{dt} = \frac{2e * x }{\mu_o * N * r^2}[/tex]ggl;

Here  [tex]\mu_o[/tex] is the permeability of free space with value

          [tex]\mu_o = 4\pi * 10^{-7} \ N/A^2[/tex]

=>     [tex]\frac{di}{dt} = \frac{2 * 8.20*10^{-6} * 0.0345 }{ 4\pi * 10^{-7} * 450 * (0.0117)^2}[/tex]

=>      [tex]\frac{di}{dt} = 7.31 \ A/s[/tex]

The value of di/dt from the given values of the solenoid electric field is;

di/dt = 7.415 A/s

We are given;

Number of turns; N = 450 per m

Radius; r = 1.17 cm = 0.0117 m

Electric Field; E = 8.2 × 10⁻⁶ V/m

Position of electric field; r' = 3.45 cm = 0.0345 m

According to Gauss's law of electric field;

∫| E*dl | = |-d∅/dt |

Now, ∅ = BA = μ₀niA

where;

n is number of turns

i is current

A is Area

μ₀ = 4π × 10⁻⁷ H/m

Thus;

E(2πr') = (d/dt)(μ₀niA)  (negative sign is gone from the right hand side because we are dealing with magnitude)

Since we are looking for di/dt, then we have;

E(2πr') = (di/dt)(μ₀nA)

Making di/dt the subject of the formula gives;

di/dt = E(2πr')/(μ₀nA)

Plugging in the relevant values gives us;

di/dt = (8.2 × 10⁻⁶ × 2 × π × 0.0345)/(4π × 10⁻⁷ × 450 × π × 0.0117²)

di/dt = 7.415 A/s

Read more at; https://brainly.com/question/14003638

A 2100 kg truck traveling north at 38 km/h turns east and accelerates to 55 km/h. (a) What is the change in the truck's kinetic energy

Answers

Answer:

Change in kinetic energy (ΔKE) = 12.8 × 10⁴ J

Explanation:

Given:

Mass of truck(m) = 2,100 kg

Initial speed(v1) = 38 km/h = 38,000 / 3600 = 10.56 m/s

Final speed(v2) = 55 km/h = 55,000 / 3600 = 15.28 m/s

Find:

Change in kinetic energy (ΔKE)

Computation:

Change in kinetic energy (ΔKE) = 1/2(m)[v2² - v1²]

Change in kinetic energy (ΔKE) = 1/2(2100)[15.28² - 10.56²]

Change in kinetic energy (ΔKE) = 1,050[233.4784 - 111.5136]

Change in kinetic energy (ΔKE) = 1,050[121.9648]

Change in kinetic energy (ΔKE) = 128063.04

Change in kinetic energy (ΔKE) = 12.8 × 10⁴ J

Suppose a 1300 kg car is traveling around a circular curve in a road at a constant
9.0 m/sec. If the curve in the road has a radius of 25 m, then what is the
magnitude of the unbalanced force that steers the car out of its natural straight-
line path?

Answers

Answer:

F = 4212 N

Explanation:

Given that,

Mass of a car, m = 1300 kg

Speed of car on the road is 9 m/s

Radius of curve, r = 25 m

We need to find the magnitude of the unbalanced force that steers the car out of its natural straight-  line path. The force is called centripetal force. It can be given by :

[tex]F=\dfrac{mv^2}{r}\\\\F=\dfrac{1300\times 9^2}{25}\\\\F=4212\ N[/tex]

So, the force has a magnitude of 4212 N

Water pressurized to 3.5 x 105 Pa is flowing at 5.0 m/s in a horizontal pipe which contracts to 1/3 its former area. What are the pressure and velocity of the water after the contraction

Answers

Answer:

the pressure after contraction is 2×10^5 Pa

the speed after contraction is 15m/s

Explanation:

We were given Pressure P to be 3.5 x 10^5 that is Flowing with speed of 5.0 m/s,

For us to calculate pressure we need to calculate the area first as;

Let initial Area = A₁

And Final area A₂

We were told that in a horizontal pipe it contracts to 1/3 its former area. Which means

A₂= A₁/3.................

V₁ is the speed

the pressure and speed of the water after the contraction can be calculated using equation of continuity below

A₂V₂ = A₁V₁

But

If we substitute given value in the expresion we have

V₂ = (3A *5)/A

V₂ = 15m/s

Therefore, the speed after contraction is 15m/s

Now we can calculate the pressure using

Bernoulli's equation

p₁ + ½ρv₁² + ρgh₁ = p₂ + ½ρv₂² + ρgh₂

But we know that the pipe is horizontal, then "h" terms cancel out then

p₁ + ½ρv₁² = p₂ + ½ρv₂²

Making P₂ subject of formula we have

p₂ = 0.5ρ( V ₁² - v₂² ) + P₁

P₂=. 0.5 × 1000 (5² -15² ) + 3*10^5

=2×10^5 Pa

Therefore, the pressure after contraction is 2×10^5 Pa

(a)  the final speed of the water after contraction is 15 m/s.

(b) The final pressure of the water after contraction is 2.5 x 10⁵ Pa.

The given parameters;

initial pressure, P₁ = 3.5 x 10⁵ Painitial speed, v₁ = 5 m/sdensity of water, ρ = 1000 kg/m³

Let the initial area of the pipe = A₁

Apply the continuity equation to determine the final speed of the water after contraction as follows;

[tex]A_1 V_1 = A_2 V_2\\\\V_2 = \frac{A_1V_1}{A_2} \\\\V_2 = \frac{A_1 \times 5}{\frac{1}{3} A_1 } \\\\V_2 = 15 \ m/s[/tex]

The final pressure of the water after contraction is determined by applying Bernoulli's equation for horizontal pipe;

[tex]P_1 + \frac{1}{2} \rho V_1^2= P_2 + \frac{1}{2} \rho V_2^2\\\\P_2 = \frac{1}{2} \rho (V_1^2 - V_2^2) + P_1\\\\P_2 = \frac{1}{2} \times 1000(5^2 - 15^2) + 3.5 \times 10^5\\\\P_2 = 2.5 \times 10^5 \ Pa[/tex]

Learn more here:https://brainly.com/question/19566865

A block of ice with mass 5.50 kg is initially at rest on a frictionless, horizontal surface. A worker then applies a horizontal force F⃗ to it. As a result, the block moves along the x-axis such that its position as a function of time is given by x(t)=αt2+βt3, where α = 0.210 m/s2 and β = 2.04×10−2 m/s3 .
A. Calculate the velocity of the object at time t = 4.50 s .
B. Calculate the magnitude of F⃗ at time t = 4.50 s .
Express your answer to three significant figures.
C. Calculate the work done by the force F⃗ during the first time interval of 4.50 s of the motion.
Express your answer to three significant figures.

Answers

Answer:

A) 3.13 m/s

B) 5.34 N

C) W = 26.9 J

Explanation:

We are told that the position as a function of time is given by;

x(t) = αt² + βt³

Where;

α = 0.210 m/s² and β = 2.04×10^(−2) m/s³ = 0.0204 m/s³

Thus;

x(t) = 0.21t² + 0.0204t³

A) Velocity is gotten from the derivative of the displacement.

Thus;

v(t) = x'(t) = 2(0.21t) + 3(0.0204t²)

v(t) = 0.42t + 0.0612t²

v(4.5) = 0.42(4.5) + 0.0612(4.5)²

v(4.5) = 3.1293 m/s ≈ 3.13 m/s

B) acceleration is gotten from the derivative of the velocity

a(t) = v'(t) = 0.42 + 2(0.0612t)

a(4.5) = 0.42 + 2(0.0612 × 4.5)

a(4.5) = 0.9708 m/s²

Force = ma = 5.5 × 0.9708

F = 5.3394 N ≈ 5.34 N

C) Since no friction, work done is kinetic energy.

Thus;

W = ½mv²

W = ½ × 5.5 × 3.1293²

W = 26.9 J

A flat loop of wire consisting of a single turn of cross-sectional area 7.30 cm2 is perpendicular to a magnetic field that increases uniformly in magnitude from 0.500 T to 3.50 T in 1.00 s. What is the resulting induced current if the loop has a resistance of 2.60

Answers

Answer:

-0.73mA

Explanation:

Using amphere's Law

ε =−dΦB/ dt

=−(2.6T)·(7.30·10−4 m2)/ 1.00 s

=−1.9 mV

Using ohms law

ε=V =IR

I = ε/ R =−1.9mV/ 2.60Ω =−0.73mA

The Milky Way has a diameter (proper length) of about 1.2×105 light-years. According to an astronaut, how many years would it take to cross the Milky Way if the speed of the spacecraft is 0.890 c?

Answers

Answer:

t = 134834.31 years

Explanation:

First we find the speed of the ship:

v = 0.890 c

where,

v = speed of the ship = ?

c = speed of light = 3 x 10⁸ m/s

Therefore, using the values, we get:

v = (0.89)(3 x 10⁸ m/s)

v = 2.67 x 10⁸ m/s

Now, we find the distance in meters:

Distance = s = (1.2 x 10⁵ light years)(9.461 x 10¹⁵/1 light year)

s = 11.35 x 10²⁰ m

Now, for the time we use the following equation:

s = vt

t = s/v

t = (11.35 x 10²⁰ m)/(2.67 x 10⁸ m/s)

t = (4.25 x 10¹² s)(1 h/3600 s)(1 day/24 h)(1 year/365 days)

t = 134834.31 years

(a) If electrons were used (electron microscope), what minimum kinetic energy would be required for the electrons

Answers

Answer:

  K = 1.6 10⁻¹⁵ J

Explanation:

In an electron microscope, electrons are used to form images, these electrons are accelerated in electric fields so that they have a kinetic energy that allows obtaining a good amplification with the microscope.

electrical potential energy is converted to kinetic energy

                U = K

                e V = ½ m v²

                v = √2eV /m

the wavelength of these electrons we obtain from the de Broglie equation

                λ = h / p

p = mv

               λ = h / mv

               λ = h / mra 2eV / m

               λ = h / ra 2eVm

where we can see that as the potential energy increases, it electrifies the shorter the wavelength of the electrons and consequently the greater the magnification of the microscope

in general these microscopes use from 10000X onwards therefore for this saponification

                K = e V

               K = 1.6 10⁻¹⁹ 10000

               K = 1.6 10⁻¹⁵ J

Two blocks A and B have a weight of 11 lb and 5 lb , respectively. They are resting on the incline for which the coefficients of static friction are μA = 0.16 and μB = 0.23. Determine the incline angle θ for which both blocks begin to slide. Also find the required stretch or compression in the connecting spring for this to occur. The spring has a stiffness of k = 2.1 lb/ft .

Answers

Answer:

[tex]\theta=10.20^{\circ}[/tex]  

[tex]\Delta l=0.10 ft[/tex]    

Explanation:

First of all, we analyze the system of blocks before starting to move.

[tex]\Sum F_{x}=P_{A}sin(\theta)+P_{B}sin(\theta)-F_{fA}-F_{fB}=0[/tex]  

[tex]\Sum F_{x}=11sin(\theta)+5sin(\theta)-0.16N_{A}-0.23N_{B}=0[/tex]

[tex]11sin(\theta)+5sin(\theta)-0.16P_{A}cos(\theta)-0.23P_{B}cos(\theta)=0[/tex]

[tex]11sin(\theta)+5sin(\theta)-0.16*11cos(\theta)-0.23*5cos(\theta)=0[/tex]

[tex]11sin(\theta)+5sin(\theta)-0.16*11cos(\theta)-0.23*5cos(\theta)=0[/tex]  

[tex]16sin(\theta)-2.91cos(\theta)=0[/tex]  

[tex]tan(\theta)=0.18[/tex]  

[tex]\theta=arctan(0.18)[/tex]  

[tex]\theta=10.20^{\circ}[/tex]  

Hence, the incline angle θ for which both blocks begin to slide is 10.20°.

Now, if we do a free body diagram of block A we have that after the block moves, the spring force must be taken into account.  

[tex]P_{A}sin(\theta)-F_{fA}-F_{spring}=0[/tex]

Where:

[tex]F_{spring} = k\Delta l=2.1\Delta l[/tex]

[tex]P_{A}sin(\theta)-0.16*11cos(\theta)-2.1\Delta l=0[/tex]

[tex]\Delta l=\frac{11sin(\theta)-0.16*11cos(\theta)}{2.1}[/tex]

[tex]\Delta l=0.10 ft[/tex]    

Therefore, the required stretch or compression in the connecting spring is 0.10 ft.

I hope it helps you!

(a) The inclined angle for which both blocks begin to slide is 10.3⁰.

(b) The compression of the spring is 0.22 ft.

The given parameters;

mass of block A, = 11 lbmass of block B, = 5 lbcoefficient of static friction for A, = 0.16coefficient of static friction for B, = 0.23 spring constant, k = 2.1 lb/ft

The normal force on block A and B:

[tex]F_n_A = m_Agcos \ \theta\\\\F_n_B = m_Bgcos \ \theta[/tex]

The frictional force on block A and B:

[tex]F_f_A = \mu_s_AF_n_A \\\\F_f_B = \mu_s_BF_n_A[/tex]

The net force on the blocks when they starts sliding;

[tex](m_Ag sin \theta+ m_Bgsin\theta) - (F_f_A + F_f_B) = 0\\\\m_Ag sin \theta+ m_Bgsin\theta = F_f_A + F_f_B\\\\m_Ag sin \theta+ m_Bgsin\theta = \mu_Am_Agcos\theta \ + \ \mu_Bm_Bgcos\theta\\\\gsin\theta(m_A + m_B) = gcos\theta (\mu_Am_A + \mu_Bm_B)\\\\\frac{sin\theta}{cos \theta} = \frac{\mu_Am_A\ + \ \mu_Bm_B}{m_A\ + \ m_B} \\\\tan\theta = \frac{(0.16\times 11) \ + \ (0.23 \times 5)}{11 + 5} \\\\tan\theta = 0.1819\\\\\theta = tan^{-1}(0.1819)\\\\\theta = 10.3 \ ^0[/tex]

The change in the energy of the blocks is the work done in compressing the spring;

[tex]\Delta E = W\\\\F_A (sin \theta )d- \mu F_n d= \frac{1}{2} kd^2\\\\F_A sin\theta \ - \ \mu F_A cos\theta = \frac{1}{2} kd\\\\d = \frac{2F_A(sin\theta - \mu cos \theta) }{k} \\\\d = \frac{2\times 11(sin \ 10.3\ - \ 0.16\times cos \ 10.3) }{2.1} \\\\d = 0.22 \ ft[/tex]

Learn more here:https://brainly.com/question/16892315

Equal currents of magnitude I travel into the page in wire M and out of the page in wire N. The direction of the magnetic field at point P which is at the same distance from both wires is

Answers

Answer:

The direction of the magnetic field on point P, equidistant from both wires, and having equal magnitude of current flowing through them will be pointed perpendicularly away from the direction of the wires.

Explanation:

Using the right hand grip, the direction of the magnet field on the wire M is counterclockwise, and the direction of the magnetic field on wire N is clockwise. Using this ideas, we can see that the magnetic flux of both field due to the currents of the same magnitude through both wires, acting on a particle P equidistant from both wires will act in a direction perpendicularly away from both wires.

Polarized light passes through a polarizer. If the electric vector of the polarized light is horizontal what, in terms of the initial intensity I0, is the intensity of the light that passes through a polarizer if the polarizer is tilted 22.5° from the horizontal?

Answers

Answer: I0*0.853

Explanation:

Ok, the Malus's law says that:

If you have light polarized along a given line with an intensity I0, and it passes through a polaroid which axis of polarization forms an angle θ with respect to the polarization of the light, then the intensity of the resulting beam is:

I(θ) = I0*cos^2(θ)

For example, if the axis of the polaroid is exactly the same as the axis of polarization of the light beam that will impact it, then we have θ = 0°, and the equation above says that the intensity of the beam will not change.

In this particular case, we have that the intensity of the light is I0, and the angle is θ = 22.5°

Then:

I(22.5°) = I0*cos^2(22.5°) = I0*0.853

Assume that the speed of light in a vacuum has the hypothetical value of 18.0 m/s. A car is moving at a constant speed of 14.0 m/s along a straight road. A home owner sitting on his porch sees the car pass between two telephone poles in 6.76 s. How much time does the driver of the car measure for his trip between the poles

Answers

Answer:

4.245s

Explanation:

Given that,

Hypothetical value of speed of light in a vacuum is 18 m/s

Speed of the car, 14 m/s

Time given is 6.76 s, and we're asked to find the observed time, T

The relationship between the two times can be given as

T = t / √[1 - (v²/c²)]

The missing variable were looking for is t, and we can find it if we rearrange the formula and make t the subject

t = T / √[1 - (v²/c²)]

And now, we substitute the values and insert into the equation

t = 6.76 * √[1 - (14²/18²)]

t = 6.76 * √[1 - (196/324)]

t = 6.76 * √(1 - 0.605)

t = 6.76 * √0.395

t = 6.76 * 0.628

t = 4.245 s

Therefore, the time the driver measures for the trip is 4.245s

A 137 kg horizontal platform is a uniform disk of radius 1.53 m and can rotate about the vertical axis through its center. A 68.7 kg person stands on the platform at a distance of 1.19 m from the center, and a 25.9 kg dog sits on the platform near the person 1.45 m from the center. Find the moment of inertia of this system, consisting of the platform and its population, with respect to the axis.

Answers

Answer:

The moment of inertia is  [tex]I= 312.09 \ kg \cdot m^2[/tex]

Explanation:

From the question we are told that

    The  mass of the platform is   m =  137 kg

     The radius is  r  =  1.53 m

    The mass of the person is  [tex]m_p = 68.7 \ kg[/tex]

    The distance of the person from the center is  [tex]d_c =1.19 \ m[/tex]

    The mass of the dog is  [tex]m_d = 25.9 \ kg[/tex]

     The distance of the dog from the person [tex]d_d = 1.45 \ m[/tex]

Generally the moment of inertia of the system is mathematically represented as

      [tex]I = I_1 + I_2 + I_3[/tex]

Where [tex]I_1[/tex] is the moment of inertia of the platform which mathematically represented as

          [tex]I_1 = \frac{m * r^2}{2}[/tex]

substituting values

           [tex]I_1 = \frac{ 137 * (1.53)^2}{2}[/tex]

           [tex]I_1 = 160.35 \ kg\cdot m^2[/tex]

Also  [tex]I_2[/tex]  is the moment of inertia of the person about the axis which is mathematically represented as

          [tex]I_2 = m_p * d_c^2[/tex]

substituting values

          [tex]I_2 = 68.7 * 1.19^2[/tex]

          [tex]I_2 = 97.29 \ kg \cdot m^2[/tex]

Also  [tex]I_3[/tex]  is the moment of inertia of the dog about the axis which is mathematically represented as

          [tex]I_3 = m_d * d_d^2[/tex]

substituting values

          [tex]I_3 = 25.9 * 1.45^2[/tex]

          [tex]I_3 = 54.45 \ kg \cdot m^2[/tex]

Thus  

        [tex]I= 160.35 + 97.29 + 54.45[/tex]

        [tex]I= 312.09 \ kg \cdot m^2[/tex]

A car is going 8 meters per second on an access road into a highway
and then accelerates at 1.8 meters per second squared for 7.2
seconds. How fast is it then going?

Answers

Answer:

20.96 m/s^2 (or 21)

Explanation:

Using the formula (final velocity - initial velocity)/time = acceleration, we can plug in values and manipulate the problem to give us the answer.

At first, we know a car is going 8 m/s, that is its initial velocity.

Then, we know the acceleration, which is 1.8 m/s/s

We also know the time, 7.2 second.

Plugging all of these values in shows us that we need to solve for final velocity. We can do so by manipulating the formula.

(final velocity - initial velocity) = time * acceleration

final velocity = time*acceleration + initial velocity

After plugging the found values in, we get 20.96 m/s/s, or 21 m/s

Two identical planets orbit a star in concentric circular orbits in the star's equatorial plane. Of the two, the planet that is farther from the star must have

Answers

Answer:

The planet that is farther from the star must have a time period greater.

Explanation:

We can determine the ratio of the period's planet with the radius of the circular orbit in the star's equatorial plane:

[tex] T = 2\pi*\sqrt{\frac{r^{3}}{GM}} [/tex]     (1)

Where:

r: is the radius of the circular orbit of the planet and the star

T: is the period

G: is the gravitational constant

M: is the mass of the planet

From equation (1) we have:

[tex] T = 2\pi*\sqrt{\frac{r^{3}}{GM}} = k*r^{3/2} [/tex]   (2)          

Where k is a constant

From equation (2) we have that of the two planets, the planet that is farther from the star must have a time period greater.

I hope it helps you!

Water pressurized to 3.5 x 105 Pa is flowing at 5.0 m/s in a horizontal pipe which contracts to 1/2 its former radius. a. What are the pressure and velocity of the water after the contraction

Answers

Answer:

Explanation:

Using the Continuity equation

v X A = v' xA'

so if A is 1/2of A' then A velocity must be 2 times the A'

after-contraction v = 2 x 5.0m/s = 10m/s

Using the Bernoulli equation

p₁ + ½ρv₁² + ρgh₁ = p₂ + ½ρv₂² + ρgh₂

, the "h" terms cancel

3.5 x 10^ 5Pa + ½ x 1000kg/m³x (5.0m/s)² = p₂ + ½ x 1000kg/m³ x (10m/s)²

p₂ = 342500pa

A certain resistor dissipates 0.5 W when connected to a 3 V potential difference. When connected to a 1 V potential difference, this resistor will dissipate:

Answers

Answer:

0.056 W

Explanation:

[tex]Power = IV[/tex]

From ohms law we know that

[tex]V= IR\\\\I= \frac{V}{R} \\\\Power= \frac{V}{R}*V\\\\Power= \frac{V^2}{R}[/tex]

Given data

P1 = 0.5 Watt

P2 = ?

V1= 3 Volts

V2= 1 Volt

Thus we can solve for the power dissipated as follows

[tex]P1= \frac{V1^2}{R1}\\\\P2= \frac{V2^2}{R2}[/tex]

[tex]\frac{P1}{P2} = \frac{V1^2}{V2^2}\\\\ P2=\frac{ V2^2}{ V1^2} *P1\\\\ P2=\frac{ 1^2}{ 3^2} *0.5= 0.055= 0.056 W[/tex]

The  resistor will dissipate 0.056 Watt

Two football teams, the Raiders and the 49ers are engaged in a tug-of-war. The Raiders are pulling with a force of 5000N. Which of the following is an accurate statement?
A. The tension in the rope depends on whether or not the teams are in equilibrium.
B. The 49ers are pulling with a force of more than 5000N because of course they’d be winning.
C. The 49ers are pulling with a force of 5000N.
D. The tension in the rope is 10,000N.
E. None of these statements are true.

Answers

Answer:

E. None of these statements are true.

Explanation:

We can't say the exact or approximate amount of tension on the rope, since we do know for sure from the statement who is winning.

for A, the tension on the rope does not depend on if both teams pull are in equilibrium.

for B, the 49ers would be pulling with a force more than 5000 N, if they were winning. The problem is that we can't say with all confidence that they'd be winning.

for C, we don't know how much tension exists on the rope, and its direction, so we can't work out how much tension the 49ers are pulling the rope with.

for D,  just as for C above, we can't work out how much tension there is on the rope, since we do not know how much force the 49ers are pulling with.

we go with option E.

A 78.5-kg man floats in freshwater with 3.2% of his volume above water when his lungs are empty, and 4.85% of his volume above water when his lungs are full.

Required:
a. Calculate the volume of air he inhales - called his lung capacity - in liters.
b. Does this lung volume seem reasonable?

Answers

Answer:

A) V_air = 1.295 L

B) Volume is not reasonable

Explanation:

A) Let;

m be total mass of the man

m_p be the mass of the man that pulled out of the water because of the buoyant force that pulled out of the lung

m_3 be the mass above the water with the empty lung

m_5 be the mass above the water with full lung

F_b be the buoyant force due to the air in the lung

V_a be the volume of air inside man's lungs

w_p be the weight that the buoyant force opposes as a result of the air.

Now, we are given;

m = 78.5 kg

m_3 = 3.2% × 78.5 = 2.512 kg

m_5 = 4.85% × 78.5 = 3.80725 kg

Now, m_p = m_5 - m_3

m_p = 3.80725 - 2.512

m_p = 1.29525 kg

From archimedes principle, we have the formula for buoyant force as;

F_b = (m_displaced water)g = (ρ_water × V_air × g)

Where ρ_water is density of water = 1000 kg/m³

Thus;

F_b = w_p = 1.29525 × 9.81

F_b = 12.7064 N

As earlier said,

F_b = (ρ_water × V_air × g)

Thus;

V_air = F_b/(ρ_water × × g)

V_air = 12.7064/(1000 × 9.81)

V_air = 1.295 × 10^(-3) m³

We want to convert to litres;

1 m³ = 1000 L

Thus;

V_air = 1.295 × 10^(-3) × 1000

V_air = 1.295 L

B) From research, the average lung capacity of an adult human being is 6 litres of air.

Thus, the calculated lung volume is not reasonable

An astronomer is measuring the electromagnetic radiation emitted by two stars, both of which are assumed to be perfect blackbody emitters. For each star she makes a plot of the radiation intensity per unit wavelength as a function of wavelength. She notices that the curve for star A has a maximum that occurs at a shorter wavelength than does the curve for star B. What can she conclude about the surface temperatures of the two stars

Answers

Answer:

Star A has a higher surface temperature than star B.

Explanation:

The effective temperature of a star can be determined by means of its spectrum and Wien's displacement law:

[tex]T = \frac{2.898x10^{-3} m. K}{\lambda max}[/tex] (1)

Where T is the effective temperature of the star and [tex]\lambda_{max}[/tex] is the maximum peak of emission.  

A body that is hot enough emits light as a consequence of its temperature. For example, if an iron bar is put in contact with fire, it will start to change colors as the temperature increase, until it gets to a blue color, that scenario is known as Wien's displacement law. Which establishes that the peak of emission for the spectrum will be displaced to shorter wavelengths as the temperature increase and higher wavelengths as the temperature decreases.

Therefore, star A has a higher surface temperature than star B, as it is shown in equation 1 since T and [tex]\lambda max[/tex] are inversely proportional.

1. What was the Michelson-Morley experiment designed to do?2. When was the Michelson-Morley experiment done?3. What was the ether?4. What does the speed of a wave depend on?5. How many light beams are used in Michelson’s interferometer?6. What sort of problems did Michelson have with his first interferometer?7. How many times more sensitive was Michelson’s second interferometer?8. What did the new interferometer float on?9. What was the surprising outcome of the Michelson-Morley experiment?10. What were the implications of the experiment?11. What is the principle behind relativity?12. Who became the first American to win the Nobel Prize?13. Did Einstein base his Theory of Relativity on the Michelson-Morley experiment?

Answers

Answer:

1) designed to measure the difference in speed of light in different directions , 1887

Explanation:

1) This experiment was designed to measure the difference in speed of light in different directions and therefore find the speed of the ether.

2) was made in 1887

3) At that time it was assumed that it was the medium in which light traveled and it is everywhere

4) the speed of the wave depends on the characteristics of the medium where it travels,

for the one in a string depends on the tension and density

for an electromagnetic wave of the permittivity and permeability of the vacuum

5) In this type of interferometer the beam is divided into two rays

6) In his interrupter, he had to accurately measure the displacement of the fringes in a telescope, for which he had to minimize vibrations, he had problems in the movement of one of the arms, changes in temperature

7) In Michelsom's second experiment, the apparatus could measure 0.01 fringes by increasing the length of the arms by 11 m

8) The new interferometer floated on a bed of mercury

9) Couldn't measure any difference in speed of light in different directions

10) Physics was forced to eliminate the concept of ETHER

11) One of the principles of relativities that the speed of light is constant in all inertial efficiency systems

12) Michelson in 1907

13) It seems that Einstein did not know the results of this experiment

Based on the passage, why is it important that different ethnic groups worked together on the strike? The groups needed to avoid speaking to one another because they wouldn’t understand. The different ethnic groups believed in being separate. The groups needed to trick the owners. They needed to be able to unite even though they spoke different languages.

Answers

Answer:D

Explanation:I got it right

Answer:

They needed to be able to unite even though they spoke different languages.

Explanation:

A rollercoaster is not moving and has 50,000 J of GPE at the top of a hill. How much kinetic energy will it have halfway down the hill, assuming there is no friction

Answers

Answer:

The kinetic energy is 25000 J

Explanation:

At the top of the hill, the potential energy = 50000 J

the potential energy = mgh

where m is the mass

g is the acceleration due to gravity

h is the vertical height at the top of the hill

Note the mass of the roller coaster and acceleration due to gravity will always remain constant, so that halfway down the hill, only the height changes by half its initial value.

This means that at halfway down the hill, the potential energy of the roller coaster is

PE = [tex]mg\frac{h}{2}[/tex] = 50000/2 = 25,000 J

We also know that the total mechanical energy of a system is given as

ME = KE + PE = constant

where

ME is the mechanical energy of the system

PE is the potential energy of the system

KE is the kinetic energy of the system

Let us now analyse.

At the top of the hill, all the mechanical energy of the roller coaster is equal to its potential energy due to the height on the hill above ground, since the roller coaster is not moving (kinetic energy is energy due to motion). Halfway down, the mechanical energy of the roller coaster is due to both the kinetic energy and the potential energy, since the roller coaster is moving down, and is still at a given height above the ground. Having all these in mind, we can proceed and say that at halfway down the hill, ignoring friction,

ME = KE + PE = constant

50000 = KE + 25000

therefore

KE = 25000 J

An unpolarized beam of light with an intensity of 4000 W/m2 is incident on two ideal polarizing sheets. If the angle between the two polarizers is 0.429 rad, what is the emerging light intensity

Answers

Answer:

The intensity is  [tex]I_2 = 1654 \ W/m^2[/tex]

Explanation:

From the question we are told that

    The intensity of the unpolarized light is  [tex]I_o = 4000 \ W/m^2[/tex]

    The  angle between the ideal polarizing sheet is  [tex]\theta = 0.429 \ rad = 0.429 * 57.296 = 24.58^o[/tex]

Generally the intensity of  light emerging from the first polarizer is mathematically represented as

               [tex]I_2 = \frac{I_o}{2}[/tex]

substituting values

               [tex]I_1 = \frac{4000}{2}[/tex]

                [tex]I_1 = 2000 \ W/m^2[/tex]

Then the intensity of  incident light emerging from the second polarizer is mathematically represented by Malus law as

                 [tex]I_2 = I_1 cos^2 (\theta )[/tex]

substituting values

                [tex]I_2 = 2000 * [cos (24.58)]^2[/tex]

                [tex]I_2 = 1654 \ W/m^2[/tex]

A string of holiday lights has 15 bulbs with equal resistances. If one of the bulbs
is removed, the other bulbs still glow. But when the entire string of bulbs is
connected to a 120-V outlet, the current through the bulbs is 5.0 A. What is the
resistance of each bulb?

Answers

Answer:

Resistance of each bulb = 360 ohms

Explanation:

Let each bulb have a resistance r .

Since, even after removing one of the bulbs, the circuit is closed and the other bulbs glow. Therfore, the bulbs are connected in Parallel connection.

[tex] \frac{1}{r(equivalent)} = \frac{1}{r1} + \frac{1}{r2} + + + + \frac{1}{r15} [/tex]

[tex] \frac{1}{r(equivalent)} = \frac{15}{r} [/tex]

R(equivalent) = r/15

Now, As per Ohms Law :

V = I * R(equivalent)

120 V = 5 A * r/15

r = 360 ohms

Two ice skaters push off against one another starting from a stationary position. The 45.0-kg skater acquires a speed of 0.375 m/s. What speed does the 60.0-kg skater acquire in m/s

Answers

Answer:

0.2812

Explanation:

Given that

mass of skater 1, m1 = 45 kg

mass of skater 2, m2 = 60 kg

speed of skater 1, v1 = 0.375 m/s

To attempt this question, we would be using the Law of conservation of momentum That says the momentum is constant, before and after the movement.

Thus, momentum p = mv

Law of conservation of momentum infers that,

m1v1 = m2v2

Now we proceed to substitute our values into the formula.

45 * 0.375 = 60 * v2

v2 = 16.875 / 60

v2 = 0.2812 m/s

Therefore the speed of the second skater has to be 0.2812 m/s

If a disk rolls on a rough surface without slipping, the acceleration of the center of gravity (G) will _ and the friction force will b

Answers

Answer:

Will be equal to alpha x r; less than UsN

Two 75 W (120 V) lightbulbs are wired in series, then the combination is connected to a 120 V supply. Part A How much power is dissipated by each bulb

Answers

Answer:

300 W

Explanation:

power of each bulb P = 75 W

voltage in the circuit = 120 V

we know that electrical power P = IV    ....1

and V = IR

we can also say that I = V/R

substituting for I in  equation 1, we have

P = [tex]V^{2}/R[/tex]    ....2

The total total power in the circuit = 75 x 2 = 150 W

from equation 2, we have

150 = [tex]120^{2} /R[/tex]

R = [tex]120^{2}/150[/tex] = 96 Ω    this is the resistance of the whole circuit.

This resistance is due to the two light bulbs, for each light bulb since they are arranged in series

R = 96/2 = 48 Ω

From P =  [tex]V^{2}/R[/tex]  

for each light bulb, power is

P = [tex]120^{2} /48[/tex] = 300 W

A ball travels with velocity given by [21] [ 2 1 ​ ], with wind blowing in the direction given by [3−4] [ 3 −4 ​ ] with respect to some co-ordinate axes. What is the size of the velocity of the ball in the direction of the wind?

Answers

Answer:

2/5 m/s

Explanation:

There are two vectors  v and w . Let θ be angle b/w the two vector.

[tex]cos\theta =\frac{\overleftarrow{v}\cdot \overleftarrow{w}}{\left | v \right |\left | w \right |}\\=\frac{6-4}{\sqrt(2^2+1^2)\sqrt(3^2+4^2)} =\frac{2}{5\sqrt(5)}[/tex]

velocity of the ball in direction of the the wind

[tex]\left | vcos\theta \right |\\\left | v \right |cos\theta\\\sqrt(2^2+1^2)\frac{2}{5\sqrt(5)} = \frac{2}{5}[/tex]

The size of the velocity of the ball in the direction of the wind is 2/5 ms.

Calculation of the size of velocity:

Since there are two vectors v and w

Also, here we assume θ be angle b/w the two vector.

So

Cos θ = 6-4 / √(2^2 + 1^2) √(3^2 + 4^2)

= 2/5√5

Now the velocity of the ball should be

= √(2^2 + 1^2) 2 ÷ 5√(5)

= 2 /5

hence, The size of the velocity of the ball in the direction of the wind is 2/5 ms.

Learn more about velocity here: https://brainly.com/question/1303810

Other Questions
In recent years, scientists have collected data on the extent of sea ice in the Arctic Ocean as shown in the graph. What additional data could be used to support or refute the theory of global climate change?O A graph providing data on daily temperature fluctuations from 1980 to 2010O A graph providing data on average global temperatures from 1980 to 2010O A graph showing monthly fluctuations in sea ice extent for each year 1980 to 2010O A graph showing yearly fluctuations in sea ice extent for each year 1980 to 2010 Which of these does NOT describe a friction that might prevent firms from choosing the optimal level of capital? A. Making too big of a change can be more expensive than making a few smaller changes. B. A firm might not be able to borrow enough to pay for the investments it wants to make. C. The firm likes its workers and doesnt want to replace some jobs with machinery. D. Some capital is very specialized and cannot be re-sold in cases of economic downturns. An inactive student wants to follow his doctor's advice by becoming more physically active. What is the most effective thing he can do to start making physical fitness a priority? (1 point) a Schedule at least 60 minutes of physical activity every day b Purchase equipment for one activity he wants to try c Fit in physical activity if he has extra time at the end of the day d Tell others about his fitness goals and workout plans Cody is a lifeguard and spots a drowning child 40 meters along the shore and 70 meters from the shore to the child. Cody runs along the shore for a while and then jumps into the water and swims from there directly to the child. Cody can run at a rate of 4 meters per second and swim at a rate of 1.1 meters per second. How far along the shore should Cody run before jumping into the water in order to save the child? Round your answer to three decimal places. Match the provided functions to a graphed function with the same zero(s). Walter Utilities is a dividend-paying company and is expected to pay an annual dividend of $1.45 at the end of the year. Its dividend is expected to grow at a constant rate of 6.50% per year. If Walter's stock currently trades for $15.00 per share, what is the expected rate of return? Which of the following best describes the graph shown below?16A1114O A This is the graph of a linear functionB. This is the graph of a one-to-one functionC. This is the graph of a function, but it is not one to oneD. This is not the graph of a function A 250.0 kg rock falls off a 40.0 m cliff. What is the kinetic energy of the rock just before it hits the ground (hint: conservation of energy)? What are the solutions to the equation 3(x 4)(x + 5) = 0? x = 4 or x = 5 x = 3, x = 4, or x = 5 x = 3, x = 4, or x = 5 x = 4 or x = 5 What is the suffix of impatiently? Compute the range and interquartile range for the data collected for boys and girls. Describe their differences in detail using specific terms of spread. (4 points) Select the correct pronoun in the box. Give the letters to Jean and ___. A. I B. me Please help!A. summerB. autumnC. winterD. spring For a ,a relationship to be a function, which values cannot repeat: the x-values or the y-values? * How does 4D shape look like? Are bacteria eukaryotes Throughout the novel, there are references to light and darkness, which take on different meanings if they are understood either literally or figuratively. What does the light figuratively symbolize? What does the darkness figuratively symbolize? (Hint: think back to Plato's "The Allegory of the Cave.") 3. What two characteristics do you need to include when defining a force? (a) speed and direction (b) strength and direction (c) acceleration and time (d) distance and direction 4. When a bug traveling west hits the windshield of a car that is traveling east, what can be said about the collision? (a) The bug feels a stronger force than the car. (b) The car and the bug feel the same size force. (c) The car accelerates more than the bug. (d) The bug does not accelerate due to the force. 5. What is the reaction force to the force on a baseball from a bat? (a) The force of the bat on the ball (b) The force of the ball on the ground (c) The force of the bat on the players hand (d) The force of gravity on the A member of the human resources department received the following email message after sending an email containing benefit and tax information to a candidate: Your message has been quarantined for the following policy violation external potential PII.Pls contact the IT security admin for further details. Which of the following BEST describes why this message was received?a. The DLP system flagged the message. b. The mail gateway prevented the message from being sent to personal email addresses c. The company firewall blocked the recipient's IP address. d. The file integrity check failed for the attached files. Place the respiratory structures into the order that air would pass through them during a normal inspiration.Outside of Body1. nares2. vestibule3. nasal cavity4. choanae5. nasopharynx6. oropharynx7. laryngopharynx8. larynxInside of Body