For a beam of light in air (n = 1) reflecting off glass (n = 1.5), what is Brewster's angle to the nearest degree?

Answers

Answer 1

Answer: 56°

Explanation:

Brewster's angle refers to the angle at the point where light of a certain polarization passes through a transparent dielectric surface and is transmitted perfectly such that no reflection is made.

The formula is;

[tex]= Tan^{-1} (\frac{n_{2} }{n_{1}} )[/tex]

[tex]= Tan^{-1} (\frac{1.5 }{1} )[/tex]

= 56.30993247

= 56°


Related Questions

An L-R-C series circuit has L = 0.450 H, C=2.50×10^−5F, and resistance R.

Required:
a. What is the angular frequency of the circuit when R = 0?
b. What value must R have to give a decrease in angular frequency of 10.0 % compared to the value calculated in Part a.

Answers

Answer:

298rad/s and 116.96 ohms

Explanation:

Given an L-R-C series circuit where

L = 0.450 H,

C=2.50×10^−5F, and resistance R= 0

In this situation we have a simple LC circuit with angular frequency

Wo = 1√LC

= 1/√(0.450)(2.50×10^-5)

= 1/√0.00001125

= 1/0.003354

= 298rad/s

B) Now we need to find the value of R such that it gives a 10% decrease in angular frequency.

Wi/W° = (100-10)/100

Wi/W° = 90/100

Wi/W° = 0.90 ............... 1

Angular frequency of oscillation

The complete aspect of the solution is attached, please check.

a. The angular frequency of the circuit when R = 0 Ohms is 294.12 rad/s.

b. The value R must have to give a decrease in angular frequency of 10.0 % compared to the initial value is equal to 116.96 Ohms.

Given the following data:

Inductance, L = 0.450 HenryCapacitance, C = [tex]2.50\times 10^{-5}[/tex] Farads

a. To determine the angular frequency of the circuit when R = 0 Ohms:

Mathematically, the angular frequency of a LC circuit is given by the formula:

[tex]\omega = \frac{1}{\sqrt{LC} } \\\\\omega =\frac{1}{\sqrt{0.450 \times 2.50\times 10^{-5}}} \\\\\omega =\frac{1}{\sqrt{1.125 \times 10^{-5}}} \\\\\omega = \frac{1}{0.0034} \\\\\omega = 294.12\;rad/s[/tex]

b. To find the value R must have to give a decrease in angular frequency of 10.0 % compared to the value calculated above:

The mathematical expression is given as follows:

[tex]\frac{\omega_f}{\omega_i} = \frac{100-10}{100} \\\\\frac{\omega_f}{\omega_i} =\frac{90}{100} \\\\\frac{\omega_f}{\omega_i} =0.9[/tex]

[tex](\frac{\omega_f}{\omega_i})^2 = 1 - \frac{R^2C}{4L} \\\\0.90^2=1 - \frac{R^2C}{4L}\\\\R=\sqrt{\frac{4L(1-0.81)}{C}} \\\\R=\sqrt{\frac{4\times 0.450 \times (0.19)}{2.50\times 10^{-5}}}\\\\R = \sqrt{\frac{0.342}{2.50\times 10^{-5}} }\\\\R =\sqrt{13680}[/tex]

R = 116.96 Ohms.

Read more: https://brainly.com/question/23754122

Which one of the following lists gives the correct order of the electromagnetic spectrum from low to high frequencies?
A) radio waves, infrared, microwaves, ultraviolet, visible, x-rays, gamma rays
B) radio waves, ultraviolet, x-rays, microwaves, infrared, visible, gamma rays
C) radio waves, microwaves, infrared, visible, ultraviolet, x-rays, gamma rays
D) radio waves, microwaves, visible, x-rays, infrared, ultraviolet, gamma rays
E) radio waves, infrared, x-rays, microwaves, ultraviolet, visible, gamma rays

Answers

Answer:

C) radio waves, microwaves, infrared, visible, ultraviolet, x-rays, gamma rays

Explanation:

radio waves have lowest  energy , lowest  frequency and highest  wavelength

gamma rays  have highest  energy , highest  frequency and least  wavelength

Answer: C

Explanation:

How much time will elapse if a radioisotope with a half-life of 88 seconds decays to one-sixteenth of its original mass?

Answers

Answer:

352 seconds are needed for the radioisotope to decay to one-sixteenth of its original mass.

Explanation:

The decay of radioisotopes are represented by the following ordinary differential equation:

[tex]\frac{dm}{dt} = -\frac{t}{\tau}[/tex]

Where:

[tex]t[/tex] - Time, measured in seconds.

[tex]\tau[/tex] - Time constant, measured in seconds.

[tex]m[/tex] - Mass of the radioisotope, measured in grams.

The solution of this expression is:

[tex]m(t) = m_{o}\cdot e^{-\frac{t}{\tau} }[/tex]

Where [tex]m_{o}[/tex] is the initial mass of the radioisotope, measured in kilograms.

The ratio of current mass to initial mass is:

[tex]\frac{m(t)}{m_{o}} = e^{-\frac{t}{\tau} }[/tex]

The time constant is now calculated in terms of half-life:

[tex]\tau = \frac{t_{1/2}}{\ln2}[/tex]

Where [tex]t_{1/2}[/tex] is the half-life of the radioisotope, measured in seconds.

Given that [tex]t_{1/2} = 88\,s[/tex], the time constant of the radioisotope is:

[tex]\tau = \frac{88\,s}{\ln 2}[/tex]

[tex]\tau \approx 126.957\,s[/tex]

Now, if [tex]\frac{m(t)}{m_{o}(t)} = \frac{1}{16}[/tex] and [tex]\tau \approx 126.957\,s[/tex], the time is:

[tex]t = -\tau \cdot \ln\frac{m(t)}{m_{o}}[/tex]

[tex]t = -(126.957\,s)\cdot \ln \frac{1}{16}[/tex]

[tex]t \approx 352\,s[/tex]

352 seconds are needed for the radioisotope to decay to one-sixteenth of its original mass.

As a skydiver falls, his potential energy ___ and his kinetic energy __​
increases,increases
increases,decreases
decreases,increases
decreases, decreases

Answers

Answer:

Hey there!

PE=mgh, so as height decreases, so does the potential energy.

KE=mv^2, so as velocity increases, kinetic energy increases.

Thus, the correct answer would be Decreases, Increases.

Let me know if this helps :)

A velocity selector can be used to measure the speed of a charged particle. A beam of particles is directed along the axis of the instrument. A parallel plate capacitor sets up an electric field E which is oriented perpendicular to a uniform magnetic field B. If the plates are separated by 3 mm and the value of the magnetic field is 0.3 T, what voltage between the plates will allow particles of speed 5 x 105 m/s to pass straight through without deflection? A. 70 V B. 140 V C. 450 V D. 1,400 V E. 2,800 V

Answers

Answer:

C. 450v

Explanation:

Using

Voltage= B*distance of separation*velocity

3mm x 0.3T x 5E5m/s

= 450v

Select the situation for which the torque is the smallest.

a. A 200 kg piece of silver is placed at the end of a 2.5 m tree branch.
b. A 20 kg piece of marble is placed at the end of a 25 m construction crane arm.
c. A 8 kg quartz rock is placed at the end of a 62.5 m thin titanium rod.
d. The torque is the same for two cases.
e. The torque is the same for all cases.

Answers

Answer:

e. The torque is the same for all cases.

Explanation:

The formula for torque is:

τ = Fr

where,

τ = Torque

F = Force = Weight (in this case) = mg

r = perpendicular distance between force an axis of rotation

Therefore,

τ = mgr

a)

Here,

m = 200 kg

r = 2.5 m

Therefore,

τ = (200 kg)(9.8 m/s²)(2.5 m)

τ = 4900 N.m

b)

Here,

m = 20 kg

r = 25 m

Therefore,

τ = (20 kg)(9.8 m/s²)(25 m)

τ = 4900 N.m

c)

Here,

m = 8 kg

r = 62.5 m

Therefore,

τ = (8 kg)(9.8 m/s²)(62.5 m)

τ = 4900 N.m

Hence, the correct answer will be:

e. The torque is the same for all cases.

A woman was told in 2020 that she had exactly 15 years to live. If she travels away from the Earth at 0.8 c and then returns at the same speed, the last New Year's Day the doctors expect her to celebrate is:

Answers

Answer:

2035

Explanation:

The doctor does not travel with the woman, and therefore, he won't experience any relativistic effect on his time. The doctor will judge time by the time here on earth. Technically, the last new year's day the doctor, who is here on earth, would expect the woman to celebrate will be in 2020 + 15 years = 2035

You are performing an experiment that requires the highest-possible magnetic energy density in the interior of a very long current-carrying solenoid. Which of the following adjustments increases the energy density?a. Increasing only the length of the solenold while keeping the turns per unit lengh flxed. b. Increasing the number of turns per unit length on the solenold. c. Increasing the cross-sectional area of the solenoid. d. None of these. e. Increasing the current in the solenoid.

Answers

Answer:

The correct choice is B & E.  

Explanation:

A solenoid is a coil of wire (usually copper) which is used as an electromagnet. Solenoids are used to convert electrical energy to mechanical energy. When this type of device is created it is also called a solenoid. One can increase the energy density within the solenoid or the coil by upping the electric current in the coil.

Cheers!

A locomotive is pulling three train cars along a level track with a force of 100,000N. The car next to the locomotive has a mass of 80,000kg, next one, 50,000kg, and the last one, 70,000 kg. you can neglect the friction on the cars being pulled.
A) what if the magnitude of the force between that the 80,000-kg car exerts on the 50,000-kg car?
B) what is the magnitude of the force that the 50,000-kg car exerts on the 70,000-kg car?

Answers

Answer:

a) 60000 N

b) 35000 N

Explanation:

Force from locomotive = 100000 N

mass of first car = 80000 kg

mass of second car = 50000 kg

mass of third car = 70000 kg

friction is neglected in this system

Total mass of the cars = 80000 + 50000 + 70000  = 200000 kg

All the car in the system will accelerate at the same rate since they are pulled by the same force

We know that force F = ma

where

a is the acceleration of the cars

m is the total mass in the system

from this we can say that

a = F/m

a = 100000/200000 = 0.5 m/s^2

a) The total mass involved in this case = mass of the last two cars after the 80000 kg car =  50000 + 70000 = 120000 kg

therefore force exerted F = ma

F = 0.5 x 120000 = 60000 N

b) The total mass in this case = mass of the third car only = 70000 kg

F = ma

F = 70000 x 0.5 = 35000 N

A radiation worker is subject to a dose of 200 mrad/h of maximum QF neutrons for one 40 h work week. How many times the yearly allowable effective dose did she receive?

Answers

Answer:

16 times.

Explanation:

The rate of the radiation dose is , R = 200 ×10^{-3} rad/hr

Time consumed, t = 40 hr

The magnitude of Q.F for the neutrons, Q.F = 2

Thus the effective radiation dose is:

[tex]R_{Eff} = Rt(Q.F) \\= 200 \times 10^{-3} \frac{rad}{hr} (40hr)(2) \\= 16 \ rad[/tex]

Thus, the effective dose allowable yearly = 16 times

To celebrate a victory, a pitcher throws her glove straight upward with an initial speed of 5.0 m/s. How much time does it take for the glove to return to the pitcher

Answers

Answer:

The glove takes 1.02s to return to the pitchers hand.

Explanation:

Given;

initial velocity the pitcher's glove, u = 5 m/s

Apply kinematic equation

s = ut - ¹/₂gt²

where;

g is acceleration due to gravity = 9.8 m/s²

t is the time takes the glove to return to the pitchers hand

s is the displacement of the glove, which will be equal to zero when the glove returns to the pitchers hand. (s = 0)

0 = ut - ¹/₂gt²

ut = ¹/₂gt²

u = ¹/₂gt

gt = 2u

t = (2u) / g

t = (2 x 5) / 9.8

t = 1.02 s

Therefore, the glove takes 1.02s to return to the pitchers hand.

6. You push an object, initially at rest, across a frictionless floor with a constant force for a time interval t, resulting in a final speed of v for the object. You then repeat the experiment, but with a force that is twice as large. What time interval is now required to reach the same final speed v?

Answers

Answer:

   t = t₀ / 2

Explanation:

In this exercise we must use Newton's second law

          F = m a

          a = F / m

now we can use kinematics

  as in object part of rest (v₀ = 0)

        v =a t₀

        t₀ = v / a

these results are with the first experiment

now repeat the experiment, but F = 2F₀

           a = 2F₀ / m = 2 a₀

          v = 2 a₀ t

          t = v / 2a₀

          t = t₀ / 2

The time interval that is required to reach the same final speed (V) is equal to [tex]t=\frac{\Delta t}{2}[/tex].

Given the following data:

Initial speed = 0 m/s (since the object is at rest)Final speed = VTime = [tex]\Delta t[/tex]Speed = V

To find the time interval that is now required to reach the same final speed (V), we would apply Newton's Second Law of Motion:

Mathematically, Newton's Second Law of Motion is given by this formula;

[tex]F = \frac{M(V-U)}{t}[/tex]

Where:

F is the force.V is the final velocity.U is the initial velocity.t is the time.

Substituting the given parameters into the formula, we have;

[tex]F = \frac{M(V-0)}{\Delta t}\\\\F = \frac{MV}{\Delta t}[/tex]

When the experiment is repeated, the magnitude of the force is doubled:

[tex]F = 2F[/tex]

Now, we can find the time interval that is required to reach the same final speed (V):

[tex]F = \frac{M(V-0)}{t}\\\\t=\frac{MV}{F}[/tex]

Substituting the value of F, we have:

[tex]t=\frac{MV}{2F} \\\\t=\frac{MV}{\frac{2MV}{\Delta t}} \\\\t=MV \times \frac{\Delta t}{2MV} \\\\t=\frac{\Delta t}{2}[/tex]

Read more here: https://brainly.com/question/24029674

A hot cup of coffee is placed on a table. Which will happen because of conduction? Answer options with 4 options A. The temperature of the coffee will decrease while the temperature of the table decreases. B. The temperature of the coffee will increase while the temperature of the table increases. C. The temperature of the coffee will decrease while the temperature of the table increases. D. The temperature of the coffee will increase while the temperature of the table decreases.

Answers

Answer:

C.

Explanation:

C. The temperature of the coffee will decrease while the temperature of the table increases.

A stationary coil is in a magnetic field that is changing with time. Does the emf induced in the coil depend

Answers

Answer:

Explanation:

The e.m.f induced in the coil depend on the following :

(a) No. of turns in the coil

(b) Cross-sectional Area of the coil

(c) Magnitude of Magnetic field

(d) Angular velocity of the coil

If a convex lens were made out of very thin clear plastic filled with air, and were then placed underwater where n = 1.33 and where the lens would have an effective index of refraction n = 1, the lens would act in the same way
a. as a flat refracting surface between water and air as seen from the water side.
b. as a concave mirror in air.
c. as a concave lens in air.
d. as the glasses worn by a farsighted person.
e. as a convex lens in air.

Answers

Answer:

D. A convex lens in air

Explanation:

This is because the air tight plastic under water will reflect light rays in the same manner as a convex lens

An optical disk drive in your computer can spin a disk up to 10,000 rpm (about 1045 rad/s ). If a particular disk is spun at 998.0 rad/s while it is being read, and then is allowed to come to rest over 0.502 seconds , what is the magnitude of the average angular acceleration of the disk?

Answers

Answer:

1988.05 rad/s^2

Explanation:

The angular speed of the optical disk ω = 998.0 rad/s

the time taken to come to rest t = 0.502 s

The magnitude of the average angular acceleration ∝ = ω/t

∝ = 998.0/0.502 = 1988.05 rad/s^2

Which of the following frequencies could NOT be present as a standing wave in a 2m long organ pipe open at both ends? The fundamental frequency is 85 Hz.

Answers

Answer:

382Hz

Explanation:

The question lacks the required option. Find the complete question in the attachment.

The long organ pipe open at both ends is called an open pipe. The fundamental frequency for an open pipe is expressed as F0 = V/2L

Harmonics are integral multiples of the fundamental frequency. For open pipes its harmonics are 2fo, 3fo, 4fo, 5fo...

Given fundamental frequency f0 to be 85 Hz, the following frequencies will be present as a standing wave;

First overtone f1 = 2fo = 2(85) = 170Hz

Second overtone f2 = 3fo = 3(85) = 255Hz

Third overtone = 4fo = 4(85) = 340Hz

Based on the option it can be seen that the only frequency that is not present as a standing wave is 382Hz

A hammer is used to hit a nail into a board. Which statement is correct about the forces at play between the nail and the hammer?
O The nail exerts a much smaller force on the hammer in the opposite direction
O The nail exerts a much smaller force on the hammer in the same direction.
The nail exerts an equal force on the hammer in the same direction.
O The nail exerts an equal force on the hammer in the opposite direction.

Answers

Answer:

reviewing the final statements, the correct one is the quarter

The nail exerts an equal force on the hammer in the opposite direction.

Explanation:

This is an action-reaction problem or Newton's third law, which states that forces in naturals occur in pairs.

This is the foregoing, the hammer exerts a force on the nail of magnitude F and it will direct downwards, if we call this action and the nail exerts a force on the hammer of equal magnitude but opposite direction bone directed upwards, each force is applied in one of the bodies.

The difference in result that each force is that the force between the nail exerts a very high pressure (relation between the force between the nail area), instead the area of ​​the hammer is much greater, therefore the pressure is small.

When reviewing the final statements, the correct one is the quarter

The nail exerts an equal force on the hammer in the opposite direction.

Tech A says parallel circuits are like links in a chain. Tech B says total current in a parallel circuit equals the sum of the current flowing in each branch of the circuit. Who is correct?

Answers

Answer: Only Tech B is correct.

Explanation:

First, tech A is wrong.

The circuits that can be compared with links in a chain are the series circuit, and it can be related to the links in a chain because if one of the elements breaks, the current can not flow furthermore (because the elements in the circuit are connected in series) while in a parallel circuit if one of the branches breaks, the current still can flow by other branches.

Also in a parallel circuit, the sum of the currents of each path is equal to the current that comes from the source, so Tech B is correct, the total current is equal to the sum of the currents flowing in each branch of the circuit.

Light of wavelength 550 nm is incident on a slit having a width of 0.200 mm. The viewing screen is 1.90 m from the slit. Find the width of the central bright fringe

Answers

Answer:

The width of Center bright fringe is 10.2mm

Explanation:

Given that if

Y/ L << 1 then

Sin theta will be approx Y/L

So sin theta approx Y/L = lamda/a

Y= a x lambda/a

By substituting

1.9x 10^ -3m x 550*10^-9/ 0.2 x 10^-3m

= 5.2mm

But

Change in y = 2y = 10.4mm

You have a lightweight spring whose unstretched length is 4.0 cm. First, you attach one end of the spring to the ceiling and hang a 1.8 g mass from it. This stretches the spring to a length of 5.1 cm . You then attach two small plastic beads to the opposite ends of the spring, lay the spring on a frictionless table, and give each plastic bead the same charge. This stretches the spring to a length of 4.3 cm .

Requried:
What is the magnitude of the charge (in nC) on each bead?

Answers

Answer:

2.2nC

Explanation:

Call the amount by which the spring’s unstretched length L,

the amount it stretches while hanging x1

and the amount it stretches while on the table x2.

Combining Hooke’s law with Newton’s second law, given that the stretched spring is not accelerating,

we have mg−kx1 =0, or k = mg /x1 , where k is the spring constant. On the other hand,

applying Coulomb’s law to the second part tells us ke q2/ (L+x2)2 − kx2 = 0 or q2 = kx2(L+x2)2/ke,

where ke is the Coulomb constant. Combining these,

we get q = √(mgx2(L+x2)²/x1ke =2.2nC

A wire carries current in the plane of this paper toward the top of the page. The wire experiences a ma netic force toward the right edge of the page. The direction of the magnetic field causing this force is:
A. in the plane of the page and toward the left edge
B. in the plane of the page and toward the bottom edge
C. upward out of the page
D. downward into the page

Answers

Answer:

D) True. In this case the thumb goes up the page, the fingers are extended out of the page and the palm points to the left

Explanation:

The magnetic force on a conductor is given by

        F = i L x B

bold letters indicate vectors. We can write this expression in the form of magnitudes

         F = i L B sin θ

The direction of the force can be found by the rule of the right hand, the thumb points in the direction of the current, the fingers extended in the direction of the magnetic field and the palm gives the direction of the force

Let's apply this expression to the case presented.

A) False. In this case the force is out of the page and is in contradiction with the real force

B) False. In this case the force is zero since the displacement of the current and the field would be parallel

C) False. In this case the force is to the left

D) True. In this case the thumb goes up the page, the fingers are extended out of the page and the palm points to the left

A uniform meter stick is hung at its center from a thin wire. It is twisted and oscillates with a period of 5 s. The meter stick is then sawed off to a length of 0.76 m, rebalanced at its center, and set into oscillation. With what period does it now oscillate?

Answers

Answer:

The new time period is  [tex]T_2 = 3.8 \ s[/tex]

Explanation:

From the question we are told that

  The period of oscillation is  [tex]T = 5 \ s[/tex]

   The  new  length is  [tex]l_2 = 0.76 \ m[/tex]

Let assume the original length was [tex]l_1 = 1 m[/tex]

Generally the time period is mathematically represented as

         [tex]T = 2 \pi \sqrt{ \frac{ I }{ mgh } }[/tex]

Now  I is the moment of inertia of the stick which is mathematically represented as

           [tex]I = \frac{m * l^2 }{12 }[/tex]

So

        [tex]T = 2 \pi \sqrt{ \frac{ m * l^2 }{12 * mgh } }[/tex]

Looking at the above equation we see that

        [tex]T \ \ \ \alpha \ \ \ l[/tex]

=>    [tex]\frac{ T_2 }{T_1} = \frac{l_2}{l_1}[/tex]

=>    [tex]\frac{ T_2}{5} = \frac{0.76}{1}[/tex]

=>     [tex]T_2 = 3.8 \ s[/tex]

Radar is used to determine distances to various objects by measuring the round-trip time for an echo from the object. (a) How far away (in m) is the planet Venus if the echo time is 900 s? m (b) What is the echo time (in µs) for a car 80.0 m from a Highway Patrol radar unit? µs (c) How accurately (in nanoseconds) must you be able to measure the echo time to an airplane 12.0 km away to determine its distance within 11.5 m? ns

Answers

Answer:

a) 1.35 x 10^11 m

b) 0.53 µs

c) 8 ns

Explanation:

Radar involves the use of radio wave which has speed c = 3 x 10^8 m/s

a) for 900 s,

The distance for a round trip = v x t

==>  (3 x 10^8) x 900 =  2.7 x 10^11 m

The distance of Venus is half this round trip distance = (2.7 x 10^11)/2 = 1.35 x 10^11 m

b) for a 80.0 m distance of the car from the radar source, the radar will travel a total distance of

d = 2 x 80 = 160 m

the time taken = d/c = 160/(3 x 10^8) = 5.3 x 10^-7 s = 0.53 µs

c) accuracy in distance Δd = 11.5 m

Δt = accuracy in time = Δd/c = 11.5/(3 x 10^8) = 3.8 x 10^-8 = 38 ns

Are Quantum Physics, Quantum mechanics,Quantum Engagement same?
or, Do they branch of each others ​

Answers

Answer:

The topic of quantum entanglement is at the heart of the disparity between classical and quantum physics: entanglement is a primary feature of quantum mechanics lacking in classical mechanics. ... In the case of entangled particles, such a measurement will affect the entangled system as a whole

Explanation:

Answer:

quantum entanglement is thought to be one of the trickiest concepts in science, but the core issues are simple. And once understood, entanglement opens up a richer understanding of concepts such as the “many worlds” of quantum theory.

Explanation:

A stone is dropped from the upper observation deck of a tower, 50 m above the ground. (Assume g = 9.8 m/s2.) (a) Find the distance (in meters) of the stone above ground level at time t. h(t) = (b) How long does it take the stone to reach the ground? (Round your answer to two decimal places.) s (c) With what velocity does it strike the ground? (Round your answer to one decimal place.) m/s (d) If the stone is thrown downward with a speed of 9 m/s, how long does it take to reach the ground? (Round your answer to two decimal places.)

Answers

Answer:

A. Using displacement =Ut + 1/2gt²

=> 0 + 1/2 (-9.8)t²

= -4.9t²

So

h(t) = 50+ displacement

= 50 - 4.9t²

B. To reach the ground

h(t) = 0

So

50-4.9t²= 0

t = √ (50/4.9)

= 3.2s

C. Using

V = u+ gt

U= 0

V= - 9.8(3.2)

= 31.4m/s

D. If u = -9m/s

Then s = ut + 1/2gt²

5t- 1/2gt²

But distance from the ground is

=.> 50-5t- 4.8t²= 0

So t solving the quadratic equation

t= 3.58s

(a) The distance of the stone above the ground level at time t is [tex]h(t) = 50 - 4.9t^2[/tex]

(b) The time taken for the stone to strike the ground is 3.19 s.

(c) The velocity of the stone when it strikes the ground is 31.4 m/s.

(d) The time taken for the stone to reach the ground when thrown at the given speed is 2.41 s.

The given parameters;

height above the ground, h₀ = 50 m

The distance of the stone above the ground level at time t is calculated as;

[tex]h(t) = h_0 - ut - \frac{1}{2} gt^2\\\\h(t) = 50 - 0 -0.5\times 9.8t^2\\\\h(t) = 50 - 4.9t^2[/tex]

The time taken for the stone to strike the ground is calculated as;

[tex]t = \sqrt{\frac{2h}{g} } \\\\t = \sqrt{\frac{2\times 50}{9.8} } \\\\t = 3.19 \ s[/tex]

The velocity of the stone when it strikes the ground is calculated as;

[tex]v =u + gt\\\\v = 0 + 3.2 \times 9.8\\\\v = 31.4 \ m/s[/tex]

The time taken for the stone to reach the ground when thrown at speed of 9 m/s is calculated as;

[tex]50 = 9t + \frac{1}{2} (9.8)t^2\\\\50 = 9t + 4.9t^2\\\\4.9t^2 + 9t - 50 = 0\\\\a = 4.9 \, \ b = 9, \ \ c = -50\\\\solve \ the \ quadratic \ equation\ using \ formula \ method\\\\t = \frac{-b \ \ + /- \ \ \sqrt{b^2 - 4ac} }{2a} \\\\t = \frac{-9 \ \ + /- \ \ \sqrt{(9)^2 - 4(4.9 \times -50)} }{2(4.9)} \\\\t = 2.41 \ s \ \ or \ \ - 4.24 \ s[/tex]

Thus, the time taken for the stone to reach the ground when thrown at the given speed is 2.41 s.

Learn more here:https://brainly.com/question/9527588

The magnitude of the magnetic field at point P for a certain electromagnetic wave is 2.12 μT. What is the magnitude of the electric field for that wave at P? (c = 3.0 × 108 m/s)

Answers

Answer:

The electric field is  [tex]E = 636 \ V/m[/tex]

Explanation:

From the question we are told that

     The magnitude of magnetic field is [tex]B = 2.12 \mu T = 2.12*10^{-6} \ T[/tex]

      The value for speed of light is  [tex]c = 3.0 *10^8 \ m/s[/tex]

Generally the magnitude of the electric field at point P is

        [tex]E = B * c[/tex]

substituting values

         [tex]E = 2.12 *10^{-6} * 3.0 *10^{8}[/tex]

         [tex]E = 636 \ V/m[/tex]

The magnitude of electric field for the wave at point P is 636 V/m.

Given data:

The strength of magnetic field at point P is, [tex]B = 2.12 \;\rm \mu T=2.12 \times 10^{-6} \;\rm T[/tex].

The speed of light is, [tex]c = 3.0 \times 10^{8} \;\rm m/s[/tex].

The given problem is based on the concept of electric field and magnetic field. The electromagnetic wave works on the principle of oscillating magnetic field and electric field at the same region. We can find any of the two using the expression,

[tex]E = B \times c[/tex]

here,

E is the strength of electric field.

Solving as,

[tex]E = (2.12 \times 10^{-6}) \times (3 \times 10^{8})\\\\E = 636 \;\rm V/m[/tex]

Thus, we can conclude that the magnitude of electric field for the wave at point P is 636 V/m.

Learn more about the electric field here:

https://brainly.com/question/15800304

Find the minimum thickness (in nm) of a soap bubble that appears green when illuminated by white light perpendicular to its surface. Take the wavelength to be 549 nm, and assume the same index of refraction as water (nw

Answers

Answer:

103nm

Explanation:

Pls see attached file

Calcular la resistencia de una varilla de grafito de 170 cm de longitud y 60 mm2. Resistividad grafito 3,5 10-5 Ωm

Answers

Answer:

R = 0.992 Ω

Explanation:

En esta pregunta, dada la información que contiene, debemos calcular la resistencia de la varilla de grafito.

Matemáticamente,

Resistencia = (resistividad * longitud) / Área De la pregunta;

Resistividad = 3,5 * 10 ^ -5 Ωm

longitud = 170 cm = 1,7 m

Área = 60 mm ^ 2 = 60/1000000 = 6 * 10 ^ -5 m ^ 2

Conectando estos valores a la ecuación anterior, tenemos;

Resistencia = (3.5 * 10 ^ -5 * 1.7) / (6 * 10 ^ -5) =

(3.5 * 1.7) / 6 = 0.992 Ω

A weightlifter works out at the gym each day. Part of her routine is to lie on her back and lift a 43 kg barbell straight up from chest height to full arm extension, a distance of 0.53 m .
Part A: How much work does the weightlifter do to lift the barbell one time?
Part B: If the weightlifter does 23 repetitions a day, what total energy does she expend on lifting, assuming a typical efficiency for energy use by the body?
Part C: How many 500 Calorie donuts can she eat a day to supply that energy?

Answers

Answer:

A) Workdone = 223.57 N-m

B) 22357 J of energy

C) Number of donuts = 10.7 donuts

Explanation:

A) The work done is calculated from the formula;. Work done = Force × Distance

We are given;

Mass; m = 43 kg

Distance = 0.53 m

Force(weight) = mg = 43 × 9.81

Thus;

Work done = 43 × 9.81 × 0.53

Workdone = 223.57 N-m

B) We are told she does 23 repetitions a day.

Thus, we assume 23% efficiency.

So, Work = Energy

Thus;

At 100% efficiency;

Energy = (223.57/100%) × 23 repetitions = 5142.11 J

Now, since she is only 23% efficient, she will expend; 5142.11/0.23 J = 22357 J of energy to do 5390 J of work.

C) from conversions; 4.18 J = 1 calorie

Thus;

22357 J ÷ 4.18 J/cal = 5348.565 calories

We how many 500 calorie donuts she can eat in a day to supply that energy.

Thus;

Number of donuts = 5348.565 cal ÷ 500 cal /donut

Number of donuts = 10.7 donuts

Other Questions
A company purchased a computer system at a cost of $34,000. The estimated useful life is 8 years, and the estimated residual value is $9,000. Assuming the company uses the double-declining-balance method, what is the depreciation expense for the second year Write the equations that represent the first and second ionization steps for sulfuric acid (H2SO4) in water. Change the polar coordinates (r, ) to rectangular coordinates (x, y):(-2,sqrt2pi Find the area of the composite figure in terms of the figure (use 3.14 for pi) Rosa is trying to copy an angle. She reads and understands all of the steps, but insists on drawing circles instead of arcs. Which of the following is the best response to tell Rosa? A. It is acceptable to draw circles instead of arcs, but because they are bigger and take up more space, your drawing may become messy, increasing the chance for errors. The spread of AIDS in small-scale societies is often attributed to witchcraft and sorcery because: Select one: a. AIDS is a poorly understood disease of which there is no clear cause in the minds of the people b. modern medicine is relatively ineffective in treating AIDS c. AIDS appears to strike random, especially among the poor d. all of the above Helena builds a shed in her backyard. There is a larger section for large tools, like her lawn mower, and a smaller section for small tools. What is the length of the entire shed? What type of number is the length? List as many types of numbers for the length as you can. 10. Which of the following is NOT a method of transmission for the HIV Virus? A. O Casual contact with an infected person B. O Unprotected Sex C. O Sharing IV drug needles D. O Coming in contact with blood or body fluids Occupational fraud comes in many shapes and sizes. The fraud at Rite Aid is one such case. On February 10, 2015, the U.S. Attorney's Office for the Middle District of Pennsylvania announced that a former Rite Aid vice president, Jay Findling, pleaded guilty to charges in connection with a $29.1 million dollar surplus inventory sales/kickback scheme. Another former vice president, Timothy P. Foster, pleaded guilty to the same charges and making false statements to the authorities. Both charges are punishable by up to five years' imprisonment and a $250,000 fine.The charges relate to a nine-year conspiracy to defraud Rite Aid by lying to the company about the sale of surplus inventory to a company owned by Findling when it was sold to third parties for greater amounts. Findling would then kick back a portion of his profits to Foster.Findling admitted he established a bank account under the name "Rite Aid Salvage Liquidation" and used it to collect the payments from the real buyers of the surplus Rite Aid inventory. After the payments were received, Findling would send lesser amounts dictated by Foster to Rite Aid for the goods, thus inducing Rite Aid to believe the inventory had been purchased by J. Finn Industries, not the real buyers. The government alleged Findling received at least $127.7 million from the real buyers of the surplus inventory but, with Foster's help, only provided $98.6 million of that amount to Rite Aid, leaving Findling approximately $29.1 million in profits from the scheme. The government also alleged that Findling kicked back approximately $5.7 million of the $29.1 million to Foster.Foster admitted his role during the guilty plea stage of the trial. He voluntarily surrendered $2.9 million in cash he had received from Findling over the life of the conspiracy. Foster had stored the cash in three 5-gallon paint containers in his Phoenix, Arizona, garage.Assume you are the director of internal auditing at Rite Aid and discover the surplus inventory scheme. You know that Rite Aid has a comprehensive corporate governance system that complies with the requirements of Sarbanes-Oxley and the company has a strong ethics foundation. Moreover, the internal controls are consistent with the COSO framework.1. To encourage various groups to come forward and report fraud, Dodd-Frank extended whistle-blowing privileges and rewards to which of the following?A. Internal auditors.B. External auditors.C. The CEO.D. All of these are correct.2. Whistleblowers who meet the criteria are eligible to receive an award based on what was collected as a result of the monetary sanctions. This can vary from_________.a. 1 to 10 percent.b. 10 to 30 percent.c. 15 to 35 percent.d. 1 to 50 percent, depending on the magnitude of the fraud. What important social issue does Kate Chopin's "The Story of an Hour" primarily focus on? you walk 6 block east, 2 blocks north, 3 blocks west and then 2 blocks north. the total distance you travel is blocks What was the effect of the repeated lines on the previous slide? You have been asked to write an essay about the checks and balances of political power in the United States federal government. Which of these is the most effective topic sentence for a paragraph in this essay?A.One of the branches of the United States government is the executive branch.B.The federal government is sometimes called other things, like the "national government" or "Washington."C.This essay is about the checks and balances of political power in the United States federal government.D.The judicial branch has the following check over the legislative branch: courts can judge legislative acts to be unconstitutional. An equation for the depreciation of a car is given by y=A(1-r)t where y=current value of the car.A=original cost r=rate of depreciation and t=time in years. The value of a car is half what it originally cost. The rate of depreciation is 10%. Approximately how old is the car? Transactions are posted into ledger account from --- I keep getting this error: postfix.cpp: In function double RPN_evaluation(std::string): postfix.cpp:42:26: error: cannot convert __gnu_cxx::__alloc_traits > >::value_type {aka std::basic_string } to char for argument 1 to int isOperand(char) if(isOperand(expr.at(g))){ ^ postfix.cpp:96:1: warning: control reaches end of non-void function [-Wreturn-type] } I am not sure what I am doing wrong, help please Division ABC has $750,000 invested in assets and earned $200,000 in income. Division XYZ has $800,000 invested in assets and earned $210,000 in income. The company's target rate is 10%. Which division has the highest residual income Follow the process of completing the square to solve x^2 - 10x + 8 = 0. What is the value of the constant that will be isolated on the right side of the equation in step 3? A.-8 B.-12 C.-32 To satisfy their economic wants, people ______ goods and services. What parts of North America did Spain control?