The maximum absolute values of the shear and bending moment is 2P and 3Pₐ respectively.
(a) Diagram is shown in image.
From A to B:
+∑Fy = 0: V = -P
+∑M₁ = 0: M = -P
From B to C:
+∑Fy = 0:
-P-P-V = 0
⇒ V = -2P
+∑M₂ = 0:
Pₓ+P(x - a)+M =0
⇒ M = -2Pₓ + Pₐ
(b) The maximum bending moment occurs in a beam, when the shear force at the section is zero or changes the sign because at point of contra fixture the bending moment is zero.
Therefore
= |V|max = 2P
= |M|max = 3Pₐ
Thus, the maximum absolute values of the shear and beading moment is 2P and 3Pₐ.
-- The given question is incomplete, I answer the question in general according to my knowledge and the complete question is
"For the beam and loading shown, (a) draw the shear and bending-moment diagrams, (b) determine the maximum absolute values of the shear and bending moment." --
To know more about Absolute values
brainly.com/question/29564461
#SPJ4
show that the probability density for the ground state solution of the one dimensional coulomb potential energy in the schrodinger equation has its maximum at x=a0
Through Schrodinger equation probability, we can prove that the probability density for the ground state solution of the one dimensional coulomb potential energy in the Schrodinger equation has its maximum at x=a₀.
Given wave function is Ψ(1s) = 1/√π{1/a₀}^(3/2) e ^(x/a₀)
Probability refers to potential. The range of the value is 0 to 1. Mathematics has included probability to forecast the likelihood of certain events. The degree to which something is likely to happen is basically what probability means.
The Schrödinger equation is a linear partial differential equation that describes the wave function or state function of a quantum-mechanical system.
To find the most probable distance, differentiate the equation |Ψ(1s)|²x² with respect to x and equating to zero, we get
d / dr | 1/√π e(1/a₀)^3 / 2e^(-x/a₀) |² x² = 0
1 / π(1 / a₀)³ d / dr (e^-2x / e₀) (x²) = 0
[2e^(-2Zx / a₀) x + e^(-2Zx / a₀) {-2 / a₀} x²] = 0
2 + (-2 / a₀) x = 0
This gives x = a₀
Therefore, through Schrodinger equation probability, we can prove that the probability density for the ground state solution of the one dimensional coulomb potential energy in the Schrodinger equation has its maximum at x=a₀.
To know more about Schrodinger, refer: https://brainly.com/question/6336766
#SPJ4
Calculate the internal energy of 1.2moles of steam at 177degree
Answer:
18447 J
Explanation:
To calculate the internal energy of steam at a given temperature, we need to know the specific heat capacity of steam and the enthalpy of vaporization. The specific heat capacity of steam at a constant pressure is approximately 2.08 J/g*K, and the enthalpy of vaporization (latent heat) at 100°C is 2257 kJ/kg.
We can use the following equation to calculate the internal energy of steam at a given temperature:
U = m * Cp * (T - T_b) + m * L
Where U is the internal energy, m is the mass of the steam, Cp is the specific heat capacity of steam, T is the temperature of the steam, Tb is the boiling temperature of the steam, and L is the enthalpy of vaporization.
Since we are given the amount of steam in moles (1.2 moles) and the temperature (177°C), we can convert the moles of steam to mass using the molar mass of water (18 g/mol). The boiling temperature of water at standard atmospheric pressure is 100°C, so we can use this value for Tb.
First, we need to convert the temperature from degrees Celsius to kelvins:
T = 177°C + 273 = 450 K
Then, we can calculate the mass of the steam:
m = 1.2 moles * 18 g/mol = 21.6 g
Substituting these values into the equation for internal energy, we get:
U = 21.6 g * 2.08 J/g*K * (450 K - 273 K) + 21.6 g * 2257 kJ/kg
Solving for the internal energy, we get:
U = 18,447 J
Therefore, the internal energy of 1.2 moles of steam at 177°C is approximately 18,447 J.
Determine the momentum of …
a. … an electron (m= 9.1 x10-31 kg) moving at 2.18 x 106 m/s (as if it were in a Bohr orbit in the H atom).
b. … a 0.45 Caliber bullet (m = 0.162 kg) leaving the muzzle of a gun at 860 m/s.
c. … a 110-kg professional fullback running across the line at 9.2 m/s.
d. … a 360,000-kg passenger plane taxiing down a runway at 1.5 m/s
A. The momentum of the electron is 1.98×10⁻²⁴ Kg.m/s
B. The momentum of the Caliber bullet is 139.32 Kg.m/s
C. The momentum of the professional fullback is 1012 Kg.m/s
D. The momentum of the passenger plane is 540000 Kg.m/s
What is momentum?Momentum is defined as the product of mass and velocity. It is expressed mathematically as:
Momentum = mass × velocity
A. How do I determine the momentum of the electron?
Mass of electron = 9.1×10⁻³¹ KgVelocity of electron = 2.18×10⁶ m/sMomentum of electron =?Momentum = mass × velocity
Momentum of electron = 9.1×10⁻³¹ × 2.18×10⁶
Momentum of electron = 1.98×10⁻²⁴ Kg.m/s
B. How do I determine the momentum of the Caliber bullet?
Mass of Caliber bullet = 0.162 KgVelocity of Caliber bullet = 860 m/sMomentum of Caliber bullet =?Momentum = mass × velocity
Momentum of Caliber bullet = 0.162 × 860
Momentum of Caliber bullet = 139.32 Kg.m/s
C. How do I determine the momentum of the professional fullback?
Mass of professional fullback = 110 KgVelocity of professional fullback = 9.2 m/sMomentum of professional fullback =?Momentum = mass × velocity
Momentum of professional fullback = 110 × 9.2
Momentum of professional fullback = 1012 Kg.m/s
D. How do I determine the momentum of the passenger plane?
Mass of passenger plane = 360000 KgVelocity of passenger plane = 1.5 m/sMomentum of passenger plane =?Momentum = mass × velocity
Momentum of passenger plane = 360000 × 1.5
Momentum of passenger plane = 540000 Kg.m/s
Learn more about momentum:
https://brainly.com/question/250648
#SPJ1
What does the law of conservation of energy state?
energy cannot be destroyed but it can change forms
energy always gets used up in every chemical reaction
energy can be destroyed but not created
energy is always the same and it cannot be changed
I think it is "energy cannot be destroyed but it can change forms".
based on the graphic, in what part of the electromagnetic spectrum does vegetation have the strongest response?
Between 400 nm and 700 nm of the electromagnetic spectrum, vegetation has the strongest response.
The electromagnetic spectrum travels in waves and spans an extensive spectrum from very long radio waves to very brief gamma rays. The human eye can simplest come across only a small portion of this spectrum called visible light.
In order from maximum to lowest power, the sections of the EM spectrum are named: gamma rays, X-rays, ultraviolet radiation, visible mild, infrared radiation, and radio waves.
In a tumbler, the purple mild travels the fastest, and the violet light travels the slowest of all seven hues. Velocity and wavelength are without delay proportional.
Learn more about Electromagnetic spectrum here:-https://brainly.com/question/23423065
#SPJ4
Question
A rabbit moves a distance of 85 meters in 13 seconds.
What is the rabbits average speed?
7.26 m/s
0.15 m/s²
6.54 m/s
6.54 m/s²
Important Formula:
[tex]s=\dfrac{d}{t}[/tex]
__________________________________________________________
[tex]d=85m[/tex] (measured in meters)
[tex]t=13s[/tex] (measured in seconds)
[tex]s=?[/tex] (measured in meters per second; m/s)
__________________________________________________________
[tex]s=\dfrac{d}{t}[/tex]
[tex]s=\dfrac{85}{13}[/tex]
__________________________________________________________
[tex]\fbox{6.54 m/s},\fbox{Option C}[/tex]
NAME THAT DISORDER
For the following scenarios, identify the psychological disorder indicated (if there is definitely a disorder). Indicate the reason why you chose that diagnosis (i.e., what are the symptoms/behaviors presented). According to your textbook (or any other source you would like to use), what might be an appropriate course of treatment (use all that could apply) for the diagnosis you chose. Try to be as specific as possible.
Homework assignment is due prior to the start of class on WEDNESDAY, DECEMBER 14TH.
1. When Lila saw the policeman turn on his flashing blue lights and motion her to pull over, her heart rate increased, her mouth felt dry, and she quite nervous about what was going to happen.
2. Although doctors could find no evidence of brain damage, Ralph could not remember driving the car that was involved in the accident that resulted in the deaths of his wife and son.
3. When Sammi saw Andrea three months ago, Andrea was too busy to talk. She was involved in all kinds of plans for a vague new business that she was sure to make her a fortune. But just last week, Sammi heard that Andrea was feeling very low, was sleeping most of the time, and had given up all plans to do just about anything.
4. Timothy was having an increasingly difficult time completing his reading assignments. He was becoming unsure if what he was reading was really there or if his mind was making things up. This was not helped by the “kryptonite rays” being emitted by the smoke detector and the hidden camera spying on him from behind the mirror in his room.
5. Ever since her home was burglarized, Maria double checks to make sure the doors are locked before going to bed.
6. Randall is so afraid of bacteria that each day he must wash each dish and utensil three times in scalding, soapy water and then rinse each dish exactly twenty seconds. If he deviates from this ritual in the slightest way, he must wash all the dishes and utensils again.
7. Everything was hopeless. Francine felt that because she was such a horrible wife and mother she felt she didn’t deserve to live and that her husband should find a better person to be with. She cried all the time and couldn’t escape her sadness.
8. When the helicopter crash landed, Yusef was horrified. He and he pilot were injured and the gas tank could blow at any time. Although he had a broken arm, Yusef was able to pull both himself and the unconscious pilot out of the plane and to safety before it blew. But ever since that time, the unbroken arm he used to save himself and the pilot has been ‘paralyzed’ and Yusef does not appear to be too upset about it.
9. Carlos, who is turning 40, is very worried about having about having a heart attack since his brother, father, and grandfather died of heart attacks in their 40s.
10. On the way home, Celia found herself having difficulty breathing, and her heart was pounding so hard that she could barely see clearly. She pulled off the road where she continued to hyperventilate, feel dizzy, and have sweaty palms. After about 10 minutes or so, her breathing returned to normal and she continued on her drive home.
Where the exercise here is to name the disorder, note that:
It should be mentioned that medication (such as antidepressants or benzodiazepines) and/or counseling may be used to treat a panic disorder such as cognitive-behavioral therapy.
A suitable course of treatment for dissociative disorders may involve counseling (such as cognitive-behavioral therapy, trauma-focused therapy, or psychodynamic therapy) and/or medication.
The focus of psychodynamic therapy is on unconscious processes as they show in the client's current behavior. Client self-awareness and knowledge of the effect of the past on present behavior are the aims of psychodynamic therapy.
Learn more about Dissociative disorder:
https://brainly.com/question/20430933
#SPJ1
When the turntable is turned on and rotates at 45.0 rev/min, calculate the centripetal force needed to keep the fly from slipping?
The centripetal force needed to keep the fly from sleeping will be zero point 0.00176 Newton in magnitude.
The mass of the fly is 2 gram and it is selling itself on a phonograph turntable.
The fly is at a distance of 4 cm away from the center of the phonograph turntable and when the turntable is turned on and retreats with 45 Revolution per minute the centripetal force that would be working on the fly will be given by,
F = Mw²R
Where,
M is mass of the fly,
w is the angular speed of the fly and,
R is the radius of the turnable.
Putting all the values,
F = 0.002×(4.7)²×0.04
F = 0.00176N.
So, a centripetal force of magnitude 0.00176 Newton will be required in order to keep the fly from slipping.
To know more about centripetal force, visit,
https://brainly.com/question/20905151
#SPJ4
Complete question- A fly of mass 2.00 g is sunning itself on a phonograph turntable at a location that is 4.00 cm from the center. When the turntable is turned on and rotates at 45.0 rev/min, calculate the centripetal force needed to keep the fly from slipping?
compare the time it takes for light to travel 1000 m on the surface of the earth and in outer space.
Since light is faster in space, it takes less time for light to travel a distance of 1000m, a time difference of 0.977ns.
Light travels more slowly in a transparent medium than in the vacuum of empty space. The speed of light in any medium (air, water, glass) is determined by the refractive index of the medium. However, this exponent itself may be wavelength dependent (ie different colored rays travel at different speeds). In fact, this is why a prism splits white light into the colors of the rainbow.
The main reason that a light beam slows down in a medium has to do with the fact that the photons, or 'raw light beams', are excited by an electromagnetic field. When the field is in the ground state (vacuum), these excitations actually propagate at the vacuum speed of light. However, when there are positively charged atoms and negatively charged electrons, the electromagnetic field does not go to the ground state. There are many virtual photons. Yes, some of the photons of the passing light beam can be absorbed. After all, no material is completely transparent. But even those who aren't are moving in an environment so different from the vacuum that their paths will be different. It also depends on the structure that the molecule forms.
Learn more about light here:
https://brainly.com/question/19697218
#SPJ4
(a) A Carnot engine working in a forward direction (i.e. taking heat from a hot body and rejecting remaining heat after work to a cold body) is a heat engine. Therefore the engine to be used as a heat engine operates in a direction. as it is in contact with the heat reservoir during this segment; and, as its is in contact with cold sink.
A heat engine, symbolized by a circle in this illustration, uses some of the heat transfer to produce work.
The most effective heat engine that is theoretically possible—i.e., any machine that can transform thermal energy (heating) into mechanical energy—is the Carnot engine (work).The heat and cold reservoirs are the names given to the hot and cold items. Only the hot temperatures' absolute values affect efficiency. A portion of the heat QH that is extracted from the high-temperature source TH in the case of a heat engine is transformed into work. The ratio of net work completed to heat absorbed throughout one full cycle is known as a heat engine's thermal efficiency.
to know more about heat engine please visit.
https://brainly.com/question/13155544
#SPJ4
(1) A table tennis ball is dropped
onto the floor from a height of
4m and it rebounds to a height of
3m. If the time of contact with the floor is 0.01s, what is the magnitude and direction of the acceleration during the contact.
Answer:
Here, h1=4.00m,h92)=3.00m,Delta t =0.01 s.Letv1 be the velocity of the ball (actind downwards) just before striking the floor an dv20 be the velocity of the ball (acting upwaeds) ust after striking the floor. Then, change in velocity of the ball in time Δtv2−(−v1)v2+v1
:. acceleration, a=v2+v1Δt ..(i)
When body falls from height h1,
then u=o,v1,a=gandS=h1
As, v21=u2+2aS,
:. v_(1) ^(2) =0 + g h_(10 or v12–√gh1
Taking motion of the ball after striking the floor, then u=v2,v=0,a=−g,S=h2
As, v2=u22as,∴v21=0+2gh1orv_(1) =sqrt 32 g h_(1)Tak∈gmotionoftheballa>erstrik∈gthe⌊,⌋thenu=v_(2), v=0, a=- g, S=h_(2)As,v2=u2+2aS,wehave0 = v_(2)^(2) +2 (-g) h_92) otr v2=2–√gh2
Putting values in (i) we get,
a=2–√gh2+2–√gh1Δt)
a=2–√×9.8×3+2–√×9.8×40.01
= 1652m/s2.
Explanation:
Emily and Henry were in the lab and graphed the heating of ice to 125°C. Emily and Brad made an observation that the graph contains three sloped and two level portions. Emily and Brad determined that the two level portions in the graph represented:
The two level portions in the graph represented phase changes.
What are phase changes?
The transition of matter from one state (solid, liquid, gas, or plasma) to another is referred to as a phase change. These changes also take place when the pressure on the system varies, as well as when the system receives enough energy or loses enough energy.
The slope of the line dividing two phases is determined by the relative densities of the two phases. The solid-liquid line, for instance, slopes up and to the right if the liquid is less dense than the solid, whereas up and to the left if the liquid is denser than the solid.
Therefore the two level portions in the graph represented phase changes.
To know phase changes from the given link
https://brainly.com/question/24858284
#SPJ1
For a particular nonlinear spring, the relationship betweem the magnitude of the applied force F and the resultant displacement x from equilibrium is given by the equation F = k x^2 What is the amount of work done by stretching the spring a distace x0? A) kx0^3 B) (1/2)kx0 C) (1/2)kx0^3 D) (1/3)kx0^2 E) (1/3)kx0^3
To get the work, you have to integrate the force as a function of [tex]$x$[/tex] from zero displacement to Xo
[tex](Integral of) $\mathrm{k} \mathrm{x}^{\wedge} 2 \mathrm{dx}$ from 0 to $\mathrm{Xo}_{\mathrm{o}}=(1 / 3) \mathrm{k}\left(\mathrm{Xo}^{\wedge}\right)^{\wedge} 3$[/tex]
The work done by stretching the spring to the given distance is [tex]W=\frac{k x_0}{3}[/tex]
The given parameters:
- Applied force on the spring [tex]$=F$[/tex]
- Extension of the spring [tex]$=x_0$[/tex]
The work done by stretching the spring to the given distance is calculated as follows;
[tex]W=\frac{k x_0}{3}[/tex]
[tex]$$\begin{aligned}& W=\int_{x_a}^{x_b} F d x \\& W=\int_{x_a}^{x_b} k x^2 d x \\& W=k \int_{x_a}^{x_b} x^2 d x \\& W=k\left[\frac{x^3}{3}\right] \\& W=k\left[\frac{x_b-x_a}{3}\right] \\& W=k\left[\frac{x_0-0}{3}\right] \\& W=\frac{k x_0}{3}\end{aligned}[/tex]
Thus, the work done by stretching the spring to the given distance is
[tex]W=\frac{k x_0}{3}[/tex]
measure of energy transfer that occurs when an object is moved over a distance by an external force at least part of which is applied in the direction of the displacement.
To learn more about work done visit:
https://brainly.com/question/13662169
#SPJ4
A mass m is suspended by a massless string forming a simple pendulum of length 2.0 m. The string of the pendulum is initially at an angle of 60° with the vertically downward direction when the mass is released from rest.
The centripetal acceleration of the mass m when it is at the lowest position is 10 m/s². The correct option is A.
What is centripetal acceleration?Centripetal acceleration is a characteristic of an object's motion along a circular path. Centripetal acceleration applies to any object moving in a circle with an acceleration vector pointing in the direction of the circle's center.
A projectile is an object that is launched into the air and then moves only in response to the acceleration of gravity. The trajectory of the object is referred to as the projectile's trajectory.
The equation of projectile motion is:
[tex]V = \sqrt{2gh}\\\\\\V = \sqrt{2 \times 10 \times \dfrac{1}{2} } \\\\V = \sqrt{20}[/tex]
a² = v² / l = 20 / 2 = 10 m/s²
Therefore, the correct option is A, 10 m/s².
To learn more about centripetal acceleration, refer to the below link:
https://brainly.com/question/14465119
#SPJ1
The question is incomplete. Your most probably complete question is given below:
The centripetal acceleration of the mass m when it is at the lowest position is:
10 m/s²
5 m/s²
20 m/s²
25 m/s²
what is the length of the y component shown below?
The length of the y component shown is C. 2.0.
How to find the length ?We are given the angle of the vector, and the length of one of the components of the vetor. Given the angle we have, the available component is the hypotenuse. The y component that we are to find, will then be the opposite or perpendicular component.
To solve for the length of the y - component therefore, the useful operation would be the Sin function.
The length of the y - component would be:
Sin 42 ° = Opposite / Hypotenuse
Sin 42 ° = y component / Hypotenuse
y - component = Sin 42 ° x Hypotenuse
y - component = Sin 42 ° x 3
y - component = 0. 6691 x 3
y - component = 2. 0
In conclusion, the y - component is 2.0.
Find out more on y-component at https://brainly.com/question/3387587
#SPJ1
Full question is:
What is the length of the y-component of the vector shown below?
A. 2.2 B. 3 c. 2.0 D. 2.7A wire loop, 2 meters by 4 meters, of negligible resistance is in the plane of the page with its left end in a uniform 0.5-tesla magnetic field directed into the page, as shown above. A 5-ohm resistor is connected between points X and Y. The field is zero outside the region enclosed by the dashed lines.
If wire loop is being pulled to the right with a constant velocity of 3 meters per second , then the potential difference induced between points X and Y is 3V .
it is given that a 5Ω resistor is connected between points X and Y ;
the magnetic field (B) = 0.5 ;
length of wire (l) [tex]=[/tex] 2 ;
velocity of the wire loop (v) = 3 m/s ;
the potential difference will be induced because charge separation on the vertical hand wire of wire loop.
Points X and Y are the same as the top and bottom of left wire.
The EMF(potential difference) induced in wire is given by
EMF = B*l*v
substituting the values ,
we get
= (0.5)(2)(3) = 3V
Therefore , the induced potential difference between points X and Y is 3V .
The given question is incomplete , the complete question is
A wire loop, 2 meters by 4 meters, of negligible resistance is in the plane of the page with its left end in a uniform 0.5-tesla magnetic field directed into the page. A 5-ohm resistor is connected between points X and Y. The field is zero outside the region enclosed by the dashed lines. The loop is being pulled to the right with a constant velocity of 3 meters per second. Make all determinations for the time that the left end of the loop is still in the field, and points X and Y are not in the field.
Determine the potential difference induced between points X and Y.
Learn more about Magnetic Field here
https://brainly.com/question/27679280
#SPJ4
Students will design an experiment to determine how the magnitude of the force on a segment of straight, current-carrying wire depends on the length of the wire segment and on the strength of the magnetic field. Which of the following experimental procedures will allow the students to determine both of these relationships? A Making measurements of the force on several different straight segments of wire, increasing the length of the wire and increasing the magnetic field strength with each measurement. B Making measurements of the force on several different straight segments of wire, increasing the length of the wire and decreasing the magnetic field strength with each measurement с Making measurements of the force on several different straight segments of wire, keeping the length of the wire constant while increasing the magnetic field strength with each measurement. D Making measurements of the force on several different straight segments of wire, increasing the length of the wire while keeping the magnetic-field strength the same with each measurement, then repeating the measurements while decreasing the length of the wire and increasing the magnetic field strength with each measurement E Making measurements of the force on several different straight segments of wire, increasing the length of the wire while keeping the magnetic-field strength constant with each measurement, then repeating the measurements while keeping the length of the wire constant while increasing the magnetic field strength with each measurement.
The experimental procedures that will allow the students to determine both of these relationships is option E:
Making measurements of the force on several different straight segments of wire, increasing the length of the wire while keeping the magnetic-field strength constant with each measurement, then repeating the measurements while keeping the length of the wire constant while increasing the magnetic field strength with each measurement.What happens to the magnetic field when the length of wire increases?The formula F = IL x B calculates the magnetic force acting through a magnetic field on a current-carrying wire. The magnetic field acts on a wire when a current is conducted through it in a direction that is perpendicular to both the magnetic force.
By increasing the amount of current flowing through the wire, the magnetic field's strength can be enhanced. As you get further from the wire, the strength gets weaker. If the amount of current flowing through it stays constant, its length and thickness have no bearing.
Therefore, the length of the wire in the magnetic field has an impact on the magnetic force's strength as well. The force acting on a wire increases with wire length in a magnetic field.
Learn more about experimental procedures from
https://brainly.com/question/17274244
#SPJ1
if an object producing sound is moving away from you, you would observe a wavelength than an object moving toward you. group of answer choices
If an object producing sound is moving away from us, the wavelength of the sound heard is longer than the actual wavelength. The conclusion is from the concept of Doppler effect.
What is the Doppler effect?The Doppler's effect is a phenomenon when the source of a wave and an observer move relative to each other, the frequency heard is not the same with the actual frequency.
The equation of the Doppler effect is
f₀ = [(v ± v₀)/(v ± vs)] × fs
Where
f₀ = observer frequency of soundv = speed of sound waves (340 m/s)v₀ = observer velocityvs = source velocityfs = actual frequency of sound wavesNote:
v₀ (+) if the observer moves closer to the sound source.vs (+) if the sound source moves away from the observer.When an object producing sound is moving away from us, the frequency of the sound we heard changed.
Let's say we are at rest, it means v₀ = 0. The sound source is moving away makes vs (+).
With the Doppler's effect, we get
f₀ = [(v+0) / (v+vs)] × fs
f₀/fs = v/(v+vs)
v < v+vs
f₀ < fs
The frequency of sound we heard is lower that the actual frequency.
The wavelength is inversely proportional to the frequency. It is described in the equation:
λ = c/f
It means that the lower the frequency, the longer the wavelength.
Hence, the phenomenon which the wavelength of the sound we heard is longer than the actual wavelength when the sound source is moving away from us is called the Doppler's effect.
Here is the group of answer choices:
(a) Band width
(b) Doppler's effect
(c) Sound refraction
(d) Vibrations
Learn more about Doppler's effect here:
https://brainly.com/question/29672712
#SPJ4
A car moving with a speed of 90km/hr was brought to rest by the application of the
Brakes in 10s How far did the car travel after the brakes were applied?
The distance travelled by the car after the brake was applied is 125 m.
What is the distance travelled by the car?
The distance travelled by the car is calculated by applying the following kinematic equation as shown below.
Mathematically, the distance travelled by the car at the given average speed is calculated as;
s = [ ( v + u ) / 2 ] t
where;
v is the final velocity of the car = 0u is the initial velocity of the car = 90 km/hr = 25 m/st is the time of motion of the car = 10 sThe distance travelled by the car is calculated as;
s = [ ( 0 + 25 m/s ) / 2 ] ( 10 s )
s = 125 m
Learn more about distance travelled here: https://brainly.com/question/24283318
#SPJ1
Two point-like particles, each of mass m, are originally separated by a distance d and moving in opposite directions each with a speed of v. What is the maximum value for v so that the particles will eventually move back together under the influence of the mutual gravitational attraction?
The angular momentum of a system does not depend on the point about which it is taken, according to equation (iv). the particles eventually move back together because of mutual gravitational attraction.
How to repair?As depicted in the following diagram, assume that two particles are present at positions P and Q at some point in time.
Think about a point R that is y miles away from a point Q, or QR=y PR=dy.
LP=mv0+mvd=mvd is the system's angular momentum around point P.
I The system's angular momentum around point Q is given by LQ=mvd+mv0=mvd.....(ii)
System's angular momentum about point R is given by LR=mv(d, y)+mv(y, d)=mvd....(iii)
The result of comparing equations I (ii), and (iii) is L P = LQ = LR....... (iv)
The angular momentum of a system does not depend on the point about which it is taken, according to equation (iv).
What causes the gravitational pull of objects?All objects with mass are attracted to one another by the gravitational attraction, which has a magnitude that is directly proportional to the masses of the two objects and inversely proportional to the square of their distance from one another.
What are the benefits of gravitational attraction?Our feet remain firmly planted on the ground thanks to gravity, which also keeps the Moon in orbit around the Earth, the Earth in orbit around the Sun, the Sun in orbit around the galactic core of our Milky Way galaxy, and the Milky Way and Andromeda galaxies orbiting each other.
Learn more about galaxy here:
https://brainly.com/question/2905713
#SPJ4
In the figure, a climber leans out against a vertical ice wall that has negligible friction. Distance a is 0.945 m and distance L is 1.95 m. His center of mass is distance d = 0.89 m from the feet-ground contact point. If he is on the verge of sliding, what is the coefficient of static friction between feet and ground?
The coefficient of static friction between feet and ground is 0.2522.
What is static friction?Static friction is defined as when there is no motion between the two surfaces, the force that one surface applies to another. The friction that exists between two or more objects when they are not moving relative to one another is referred to as static friction.
The coefficient of static friction between his feet and the ground, denoted by the symbol s, determines how to express the frictional force as
fs =μsFN1
The μs can be calculated as
μs = a / √L² - a² x d / L
μs = 0.945 / √(1.95)² - (0.945)² x 0.89 / 1.95
μs = 0.945 / √2.91225 x 0.89 / 1.95
μs = 0.2522
Thus, the coefficient of static friction between feet and ground is 0.2522.
To learn more about static friction, refer to the link below:
https://brainly.com/question/13000653
#SPJ1
Joan is initially driving her car at 10 m/s when she decides to go faster. She accelerates uniformly at 4 m/s2 for 100 meters. How fast is Joan going?
a
50 m/s
b
35 m/s
c
30 m/s
d
26 m/s
Joan is going with speed 30 m/s. Hence, option (C) is correct.
What is acceleration?Acceleration is the rate at which a velocity changes over time. It qualifies as a vector quantity because it possesses both direction and magnitude. Meter/second^2 (m/s^2) is the SI unit of acceleration.
Given that: initial speed of the car: u = 10 m/s.
Uniform acceleration of the car: a = 4 m/s^2.
Distance travelled: s = 100 meters.
Let, the final speed is = v
Using the formula v² = u² + 2as, we get:
v = √(10² + 2×4×100) m/s.
= 30 m/s.
Hence, final speed of the car is 30 m/s.
Learn more about acceleration here:
brainly.com/question/12550364
#SPJ1
an astronaut drops a rock from the top of a crater on the moon when the rock is halfwat down to the bottom of the crater its speed is what fraction of its cinal impact speed?A. 1/4–√2B.1/4C. 1/2–√2D. 1/–√2Answer:
The fraction of its final impact speed is 1/√2.
Impact speed is the speed of the vehicle at the time of impact or collision.
The rock has lost half of its gravitational potential energy, its kinetic energy at the halfway point is half of its kinetic energy at impact.
As we know kinetic energy is directly proportional to mass (m) and velocity square (v²),
KE ∝ v²
KE = (1/2)mv²
then K.E at halfway point is equal to 1/2 x K.E,
Then,
The K.E at impact, then the rock’s speed at the halfway point its speed at impact will be 1/√2 its impact speed.
Therefore option D is the correct answer, the fraction of its final impact speed is 1/√2.
To know more about impact speed,
https://brainly.com/question/13163464
#SPJ4
What is the Force of Gravity acting on the object in the diagram?
The force of gravity acting on the 23 Kg object in the diagram is 225.4 N
How do I determine the force of gravity?The force of gravity is defined as follow:
Force of gravity (F) = mass (m) × acceleration due to gravity (g)
Using the above formula, we can easily obtain the force gravity acting on the 23 Kg object. This is shown below:
Mass (m) = 23 KilogramsAcceleration due to gravity (g) = 9.8 m/s²Force of gravity (F) =?Force of gravity (F) = mass (m) × acceleration due to gravity (g)
Force of gravity = 23 Kg × 9.8 m/s²
Force of gravity = 225.4 N
Thus, from the calculation made above, we can conclude that the gravitaional force is 225.4 N
Learn more about force:
https://brainly.com/question/12163222
#SPJ1
A soccer player runs at 10 m/s and runs into a 80 kg referee standing on the field causing the referee to fly forward at 6.0 m/s. Assume the soccer player comes to complete stop after impact. What would be the mass of the soccer player be?
The mass of soccer player will be 120kg. Writing down 1/2 m1 will help us remember that KE = 1/2 mv2 (v1i) 2 + 1/2 m2(vi) (vi) 2 = 1/2 m1(v1f) (v1f) 2 + 1/2 m2 (v2f) (v2f) 2.
How to solve ?According to Newton's third law,
Given that a soccer player runs at 10m/s and plows into a 80kg referee standing on the field causing the referee to fly forward at 56m/s. Let
mass of the player = ?
initial velocity of the player = 10m/s
Final velocity of the player
mass of the referee = 80 kg
Initial velocity of the referee = 0 ( since he is at rest )
Final velocity of the referee = 6 m/s
Since it is a perfectly elastic collision,
U1 =V2 - V1 ........ (1)
M1U1 = M2V2 + M1V1........ (2)
Substitute all the necessary parameters into the equation (1)
10 = 6 - V1
V1 = 10 - 6
V1 = 4 m/s
Now, Substitute all the necessary parameters into the equation (2)
10M1 = (80 x 6) + (4M1)
10 M1- 4 M1 = 480
4M1 = 480
M1 = 480/4
M1 = 120kg
Therefore, the mass of soccer player will be 120kg
Collision formula: What is it?When kinetic energy (KE) and momentum (p) are conserved during a collision, the collision is said to be elastic. To put it another way, it denotes that KE0 = KEf and po = pf. Writing down 1/2 m1 will help us remember that KE = 1/2 mv2 (v1i) 2 + 1/2 m2(vi) (vi) 2 = 1/2 m1(v1f) (v1f) 2 + 1/2 m2 (v2f) (v2f) 2.
How is velocity determined?By dividing the entire distance traveled by the time it took the object to go a certain distance, you may calculate the object's initial velocity. V, d, and t are the three variables that make up the equation V = d/t.
Learn more about Collision here:
https://brainly.com/question/12497950
#SPJ1
a particle moves under the influence of a conservative force. the equation for the potential energy as a function of position is given by: u(x)
A particle moves under the influence of a conservative force, The maximum x-coordinate of the particle at x = -3 m is 7 m.
Given that,
Potential energy of the particle u(x) = 5x² - 20x + 2
We know the relation between force and potential energy as,
F = -du/dx = -d/dx (5x² - 20x + 2) = -(10 x - 20 ) = 20 - 10 x at mean position x = 2.
At x = -3, amplitude is given by x = 2 - (-3) = 5
The maximum x co-ordinate is given as x = 5 + 2 = 7 m
To know more about potential energy function:
https://brainly.com/question/29998972
#SPJ4
Design a parallel RLC circuit (see (Figure 1)) with a resonant radian frequency of 5000 rad/s. Take that L 10 mH.a) Find the value of C Express your answer to three significant figures and include the appropriate units. C= 4.00 μFb) Find the value of R so that the response is critically damped. Express your answer to three significant figures and include the appropriate units R- 25.0 Ω
The value of R so that the response is critically damped using the equation is 25.0Ω.
What is Farads?Farads is the unit of measure for capacitance, which is the amount of electrical charge stored for a given voltage. Farads can be used to measure the amount of energy stored in a capacitor, which is made up of two conductive plates separated by an insulating material. The higher the capacitance, the more energy can be stored in a given capacitor. Farads are named after Michael Faraday, the British scientist who discovered the relationship between electricity and magnetism.
The resonant frequency of an RLC circuit is given by the equation:
ω_r=1/sqrt(LC)
where ω_r is the resonant frequency in rad/s, L is the inductance in Henries, and C is the capacitance in Farads.
Given the resonant frequency of 5000 rad/s and the inductance of 10 mH, we can calculate the capacitance as follows:
C=1/(ω_r^2*L)
C=1/(5000^2*0.01)
C=4.00μF
We can find the value of R so that the response is critically damped using the equation:
R=2*sqrt(L/C)
R=2*sqrt(0.01/4.00)
R=25.0Ω
To learn more about Farads
https://brainly.com/question/24175851
#SPJ1
A large cannon is mounted on a cart with frictionless wheels that is initially at rest on a horizontal surface. The cannon fires a large cannonball to the right with a speed v_b which is then caught by a trap firmly attached to the cart. What is the final speed of the cannoncart-cannonball system? V > v_b, to the left
The final velocity of the cannonball-cart system is less than the initial velocity of the cannonball and the system will move in the direction of the cannonball ( V < v_b ).
What is the law of conservation of linear momentum?
The law of conservation of linear momentum states that the sum of the initial momentum is equal to sum of the final momentum, provided that the system is Isolated.
Mathematically, the law of conservation of linear momentum is given as;
Pi = Pf
where;
Pi is the sum of the initial momentumPf is the sum of the final momentumm₁u₁ + m₂u₂ = v ( m₁ + m₂ )
where;
m₁ is the mass cannon ballu₁ is the initial velocity of the cannon ballm₂ is the mass of the cartu₂ is the initial velocity of the cartv is the final velocity of the cannoncart-systemsince the cart is initially at rest, the initial velocity of the cart = 0
m₁u₁ + 0 = v ( m₁ + m₂ )
m₁u₁ = v ( m₁ + m₂ )
v = ( m₁u₁ ) / ( m₁ + m₂ )
given initial velocity of the cannon ball = v_b
The final velocity of the cannonball-cart system is calculated as follows;
V = ( m₁v_b ) / ( m₁ + m₂ )
Hence, V < v_b
Learn more about linear momentum here: https://brainly.com/question/7538238
#SPJ1
which of the following sequences lists methods for determining distance in the correct order from nearest to farthest?
Parallax, main-sequence fitting, cepheid variables, Tully-Fisher relation, and Hubble's law are the sequence lists methods for determining distance.
Parallax is the closest method for determining distance. This method uses the principle of triangulation to measure the distance of a nearby star relative to Earth. Main-sequence fitting is another method used to measure the distance of stars. This method compares the brightness of a star to other stars of known distance and luminosity to determine its distance.
Cepheid variables are stars whose brightness varies in a predictable way over time. This method uses the period of the star's brightness to determine its intrinsic luminosity, and then its distance. The Tully-Fisher relation is a method for measuring the distance of galaxies. This method uses the rotation speed of the galaxy and its brightness to calculate its distance.
Finally, Hubble's law is the most distant method for determining distance. This law states that the farther away a galaxy is, the faster it moves away from us. This allows us to calculate the distance of galaxies by measuring their rate of recession.
For more questions like Hubble's law click the link below:
https://brainly.com/question/29869676
#SPJ4
the use of the doppler effect in the study of astronomy
