The surface charge density at that point with Electric field, E=15ax-8az V/m with permittivity in free space is ε=ε₀ is, σ=1.5×10⁻¹⁰ c/m². Hence, option A is correct.
The Gauss law is defined as the electric flux of the closed surface is equal to the charge enclosed by the given area. Electric flux is defined as the number of field lines crossing through a given area.
From the given area,
E = 15ax-8az V/m
ε=ε₀ (ε₀ is the permittivity in free space)=8.854×10⁻¹².
surface charge density, (σ) =?
E = σ/ε₀
σ = E×ε₀
= (15ax-8az)×8.854×10⁻¹².
= √(15)²+(8)²×8.854×10⁻¹².
= 17×8.854×10⁻¹².
= 1.50×10⁻¹⁰C/m².
Thus, the surface charge densities, σ = 1.50×10⁻¹⁰ C/m².
To learn more about Gauss law:
https://brainly.com/question/30516416
#SPJ4
A 100.0 mL sample of 0.10 M NH3 is titrated with 0.10 M HNO3. Determine the pH of the solution after the addition of 50.0 mL of KOH. The Kb of NH3 is 1.8 x 10-5, A) 4.74 B) 7.78 C) 7.05 D) 9.26 E) 10.34
The pH of the solution after the addition of 50.0 mL of KOH is 9.26
So, the correct answer is D.
The limiting reactant is the one that will be completely consumed in the reaction. In this case, NH₃ is the limiting reactant because it is present in a greater amount than the HNO₃.
This means that all of the HNO₃ will react with NH₃ and there will be some NH₃ left over.
To find the amount of NH₃ that will react, use stoichiometry:
1 mol HNO₃ reacts with 1 mol NH₃ 0.0050 mol HNO₃ reacts with 0.0050 mol NH₃This means that 0.0100 mol - 0.0050 mol = 0.0050 mol of NH₃ remains after the reaction with HNO₃.
Now, find the concentration of NH₃ after the reaction:
0.0050 mol / 0.150 L = 0.033 M NH₃
Now, calculate the pOH of the solution:
pOH = -log(1.8 x 10⁻⁵) + log(0.033) = 4.74
Finally, calculate the pH of the solution:
pH = 14 - 4.74 = 9.26
Therefore, the answer is option D) 9.26.
Learn more about chemical reaction at:
https://brainly.com/question/30663464
#SPJ11
Option (c), The solution has a pH of 7.05. We are given the volume and the molarity of NH3 and HNO3 in the equation.
So, let's first calculate the moles of NH3 present in 100.0 mL of 0.10 M NH3.
The number of moles of NH3 in the solution will be: (100.0 mL / 1000 mL/L) × 0.10 M = 0.010 moles of NH3
Also, the number of moles of HNO3 in the solution will be the same because the two are reacted in a 1:1 ratio. Therefore, the number of moles of HNO3 in the solution will also be 0.010 mol. It is now time to calculate the concentration of the solution after the addition of 50.0 mL of 0.10 M KOH. Using the balanced chemical equation, KOH reacts with HNO3 in a 1:1 ratio as follows:
KOH(aq) + HNO3(aq) → KNO3(aq) + H2O(l)
Using the volume and molarity of KOH, we can calculate the number of moles of KOH in the solution as follows:(50.0 mL / 1000 mL/L) × 0.10 M = 0.0050 moles of KOH
Now we can determine the number of moles of HNO3 left in the solution by subtracting the number of moles of KOH from the original number of moles of HNO3:Number of moles of HNO3 = 0.010 - 0.0050 = 0.0050 mol
Finally, we can calculate the concentration of HNO3 in the solution using the new total volume of the solution. Since the total volume of the solution has doubled (from 100 mL to 200 mL), the molarity of the solution is halved:
Molarity of HNO3 = 0.0050 mol / 0.200 L = 0.025 M
The Kb value for NH3 is given in the question as 1.8 x 10-5. We can use this value and the concentration of NH3 to calculate the pKb as follows:
pKb = -log(Kb) = -log(1.8 x 10-5) = 4.74
The pH of the solution can now be calculated as follows:
pH = 14.00 - pOH = 14.00 - (pKb + log([NH3]/[NH4+])) = 14.00 - (4.74 + log(0.010/0.0050)) = 7.05
Therefore, the correct option is (C) 7.05.
Learn more about the molarity: https://brainly.com/question/2817451
#SPJ11
what is the pressure on the sample if f = 340 n is applied to the lever? express your answer to two significant figures and include the appropriate units.
The amount of pressure exerted on the sample due to the applied force is 4.25 x 10⁷ Nm.
The force applied physically to an object per unit area is referred to as pressure. Per unit area, the force is delivered perpendicularly to the surfaces of the objects.
The diameter of the large cylinder, d₁ = 10 cm = 0.1 m
The diameter of the small cylinder, d₂ = 2 cm = 0.02 m
The area of the given sample, A = 4 cm² = 4 x 10⁻⁴m²
So, the force acting on the small cylinder is given by,
(F x 2L) - (F₂ x L) = 0
2FL - F₂L = 0
So,
F₂L = 2FL
Therefore, F₂ = 2 x F
F₂ = 2 x 340 N
F₂ = 680 N
In order to calculate the force acting on the large cylinder,
We know that, P₁ = P₂
So, we can write that,
F₁/A₁ = F₂/A₂
F₁/d₁² = F₂/d₂²
Therefore,
F₁ = F₂d₁²/d₂²
F₁ = 680 x (0.1/0.02)²
F₁ = 680 x 100/4
F₁ = 17000 N
Therefore, the pressure exerted on the sample is,
P = F₁/A
P = 17000/(4 x 10⁻⁴)
P = 4.25 x 10⁷ Nm
To learn more about pressure, click:
https://brainly.com/question/13327123
#SPJ4
Consider a metal pipe that carries water to a house.Which answer best explains why a pipe like this may burst in very cold weather? O The metal contracts to a greater extent than the water. O The interior of the pipe contracts less than the outside of the pipe O Both the metal and the water expand,but the water expands to a greater extent. O Water expands upon freezing while the metal contracts at lower temperatures. O Water contracts upon freezing while the metal expands at lower temperatures
A metal pipe may burst in very cold weather because water expands upon freezing while the metal contracts at lower temperatures.
The reason a metal pipe may burst in very cold weather is due to the expansion of water upon freezing, combined with the contraction of the metal at lower temperatures.
When water freezes, it undergoes a phase change from a liquid to a solid state. Unlike most substances, water expands upon freezing. This expansion is due to the formation of ice crystals, which take up more space than the liquid water molecules. As the water inside the pipe freezes and expands, it exerts pressure on the surrounding walls of the pipe.
On the other hand, metals generally contract when they are exposed to colder temperatures. This contraction occurs because the colder temperature reduces the thermal energy of the metal atoms, causing them to move closer together.
When the water inside the pipe expands due to freezing, and the metal contracts due to the cold temperature, the combined effect can exert significant pressure on the pipe. This pressure may exceed the structural strength of the pipe, leading to bursting or cracking.
A metal pipe may burst in very cold weather because water expands upon freezing while the metal contracts at lower temperatures. This combination of expansion and contraction puts pressure on the pipe, potentially exceeding its structural strength. Understanding this behavior is crucial to prevent damage and ensure the proper functioning of pipes in cold weather conditions.
To know more about metal visit:
https://brainly.com/question/28183884
#SPJ11
Determine if the following statements are true or false. Part A - When the distance between two masses is doubled, the gravitational force between them is halved. O True O False Submit Request Answer
The statement " When the distance between two masses is doubled, the gravitational force between them is halved." is false the gravitational force between them is not halved.
According to Newton's law of universal gravitation, the gravitational force between two masses is inversely proportional to the square of the distance between them.
Mathematically, the force (F) is given by F = G * (m1 * m2) / r^2, where G is the gravitational constant, m1 and m2 are the masses, and r is the distance between them.
If the distance between the masses is doubled (r → 2r), the force becomes F' = G * (m1 * m2) / (2r)² = G * (m1 * m2) / 4r². As we can see, the force is reduced by a factor of 4, not halved.
Therefore, the statement that when the distance between two masses is doubled, the gravitational force between them is halved is false. The force decreases by a factor of 4, not 2, when the distance is doubled.
To know more about gravitational force, refer here:
https://brainly.com/question/29190673#
#SPJ11
A particale's velocity function is given by V=3t³+5t²-6 with X in meter/second and t in second Find the velocity at t=2s
A particale's velocity function is given by V=3t³+5t²-6 with X in meter/se
The velocity of the particle at t=2s is 38 m/s.
The velocity function of the particle is given by V = 3t³ + 5t² - 6, where V represents the velocity in meters per second (m/s), and t represents time in seconds (s). This equation is a polynomial function that describes how the velocity of the particle changes over time.
The velocity function of the particle is V = 3t³ + 5t² - 6, we need to find the velocity at t=2s.
Substituting t=2 into the velocity function, we have:
V = 3(2)³ + 5(2)² - 6
V = 3(8) + 5(4) - 6
V = 24 + 20 - 6
V = 38 m/s
It's important to note that the velocity of the particle can be positive or negative depending on the direction of motion. In this case, since we are given the velocity function without any information about the initial conditions or the direction, we can interpret the velocity as a magnitude. Thus, at t=2s, the particle has a velocity of 38 m/s, regardless of its direction of motion.
learn more about Velocity here:
https://brainly.com/question/14236800
#SPJ11
explain the difference between the z-test for using rejection region(s) and the z-test for using a p-value.
The z-test is a hypothesis test that is used to determine if a given set of data differs significantly from the normal distribution or the population mean. The z-test involves comparing the sample mean with the population mean. It is a statistical tool used to test whether the sample mean is significantly different from the population mean.
There are two methods for performing the z-test, the rejection region method, and the p-value method. The two methods are different in the sense that one uses the critical value for the test statistic and the other uses the probability of observing the test statistic or more extreme value.
Rejection Region MethodIn the rejection region method, the null hypothesis is rejected if the calculated test statistic is less than or greater than the critical value of the test statistic. The critical value is the value beyond which the null hypothesis is rejected. The critical value is obtained from the standard normal distribution table or the t-distribution table. If the test statistic falls within the rejection region, then the null hypothesis is rejected, and the alternative hypothesis is accepted.
P-value MethodThe p-value method involves calculating the probability of obtaining a test statistic that is more extreme than the calculated test statistic under the null hypothesis. The p-value is the probability of observing the test statistic or more extreme value. If the p-value is less than the level of significance, then the null hypothesis is rejected, and the alternative hypothesis is accepted.
In summary, the z-test is a statistical tool used to test whether the sample mean is significantly different from the population mean. The rejection region method and the p-value method are two methods of performing the z-test. The two methods are different in that one uses the critical value for the test statistic and the other uses the probability of observing the test statistic or more extreme value.
To know more about z-test, visit:
https://brainly.com/question/30109604
#SPJ11
A solid surface with dimensions 2.5 mm ✕ 3.0 mm is exposed to argon gas at 90. Pa and 500 K. How many collisions do the Ar atoms make with this surface in 20. s?v
A solid surface with dimensions 2.5 mm ✕ 3.0 mm is exposed to argon gas at 90. Pa and 500 K, the Ar atoms make 4.6128 collisions with the surface in 20 seconds.
We may utilise the idea of the kinetic theory of gases to determine how many collisions the Ar (argon) atoms have with the solid surface.
The expression for the quantity of surface collisions per unit of time is:
Collisions per unit time = (Number of particles per unit volume) × (Velocity) × (Area of the surface)
Number of particles per unit volume = (Pressure) / (Gas constant * Temperature)
Number of particles per unit volume = (Pressure) / (Gas constant * Temperature)
= (90) / (8.314 * 500 K)
= 0.02154 [tex]mol/m^3[/tex]
Number of particles in the given volume = (Number of particles per unit volume) × (Volume)
= (0.02154) × (7.5 × [tex]10^{(-6)[/tex])
= 1.6155 × [tex]10^{(-7)[/tex] mol (approximately)
Number of collisions = (Number of particles in the given volume) × (Collisions per unit time) × (Time)
= (1.6155 × [tex]10^{(-7)[/tex]) × (Number of particles per unit volume) × (Velocity) × (Area of the surface) × (Time)
Velocity = √((3 * k_B * T) / M_Ar)
Velocity = √((3 * 1.380649 × [tex]10^{(-23)[/tex] J/K * 500) / (39.95 × [tex]10^{(-3)[/tex] )
≈ 1,558.45 m/s
Number of collisions = (1.6155 × [tex]10^{(-7)[/tex]) × (0.02154) × (1,558.45 m/s) × (7.5 × [tex]10^{(-6)[/tex]) × (20)
≈ 4.6128 collisions
Therefore, the Ar atoms make approximately 4.6128 collisions with the surface in 20 seconds.
For more details regarding collisions, visit:
https://brainly.com/question/13138178
#SPJ4
A solid disk rotates at an angular velocity of 0.039 rad/s with respect to an axis perpendicularto the disk at its center. The moment of intertia of the disk is0.17kg·m2. From above, sand isdropped straight down onto this rotating disk, so that a thinuniform ring of sand is formed at a distance of 0.40 m from theaxis. The sand in the ring has a mass of 0.50 kg. After all thesand is in place, what is the angular velocity of the di
Therefore, the angular velocity of the disk after all the sand is in place is 0.0265 rad/s.
When sand is dropped straight down onto the rotating disk, a thin uniform ring of sand is formed at a distance of 0.40 m from the axis.
The sand in the ring has a mass of 0.50 kg and the disk rotates at an angular velocity of 0.039 rad/s. The moment of intertia of the disk is 0.17kg·m².
The angular velocity of the disk after all the sand is in place is needed to be determined
The angular velocity of the disk after all the sand is in place can be determined using the principle of conservation of angular momentum.
Since there are no external torques acting on the system of the disk and sand, the angular momentum before the sand is dropped onto the disk is equal to the angular momentum after the sand is in place.
Therefore, we can write:
Iinitial = Ifinalwhere I is the moment of inertia and ω is the angular velocity.
We can find the initial angular momentum of the disk before the sand is dropped using the formula:
Linitial = Iinitial ωinitialwhere L is the angular momentum.
We know that the disk has a moment of inertia of 0.17 kg·m² and is rotating at an angular velocity of 0.039 rad/s. Therefore, Linitial = 0.17 kg·m² × 0.039 rad/s
= 0.00663 kg·m²/s
When the sand is dropped onto the disk, it will start rotating along with the disk due to frictional forces. Since the sand is dropped at a distance of 0.40 m from the axis, it will increase the moment of inertia of the system by an amount equal to the moment of inertia of the sand ring.
We can find the moment of inertia of the sand ring using the formula:
I ring = mr²where m is the mass of the sand and r is the radius of the ring. We know that the mass of the sand is 0.50 kg and the radius of the ring is 0.40 m.
Therefore, I ring = 0.50 kg × (0.40 m)²
= 0.08 kg·m²
The moment of inertia of the system after the sand is in place is equal to the sum of the moment of inertia of the disk and the moment of inertia of the sand ring.
Therefore, I final = 0.17 kg·m² + 0.08 kg·m²
= 0.25 kg·m²
We can now find the final angular velocity of the disk using the formula:
L final = I final ω final
We know that the angular momentum of the system is conserved.
Therefore, L initial = L finalor
0.00663 kg·m²/s = 0.25 kg·m² × ωfinalωfinal
= 0.00663 kg·m²/s ÷ 0.25 kg·m²ωfinal
= 0.0265 rad/s
To know more about velocity visit:
https://brainly.com/question/30559316
#SPJ11
Question 1 Calculate the amount of radiation emitted by a blackbody with a temperature of 353 K. Round to the nearest whole number (e.g., no decimals) and input a number only, the next question asks a
The amount of radiation emitted by a blackbody with a temperature of 353 K is 961 {W/m}².
The formula for calculating the amount of radiation emitted by a blackbody is given by the Stefan-Boltzmann law: j^* = \sigma T^4 Where j* is the radiation energy density (in watts per square meter), σ is the Stefan-Boltzmann constant (σ = 5.67 x 10^-8 W/m^2K^4), and T is the absolute temperature in Kelvin (K).Using the given temperature of T = 353 K and the formula above, we can calculate the amount of radiation emitted by the blackbody: j^* = \sigma T^4 j^* = (5.67 \times 10^{-8}) (353)^4 j^* = 961.2 {W/m}².
Therefore, the amount of radiation emitted by the blackbody with a temperature of 353 K is approximately 961 watts per square meter (W/m²).Rounding this to the nearest whole number as specified in the question gives us the final answer of: 961 (no decimals).
More on radiation: https://brainly.com/question/31106159
#SPJ11
According to the N+1 rule, a hydrogen atom that appears as a quartet would have how many neighbor H's? 3 4 5 8 Arrange the following light sources, used for spectroscopy, in order of increasing energy (lowest energy to highest energy)
They are useful for analyzing compounds in the UV range.Mercury lamps: This is the highest-energy light source used in spectroscopy. They are used for fluorescence spectroscopy because they produce a high-energy source of light that excites atoms and molecules.
It states that if a hydrogen atom is attached to N equivalent hydrogen atoms, it is split into N+1 peaks.In spectroscopy, light sources are used to analyze the properties of substances. The following are the light sources used in spectroscopy, ordered from lowest to highest energy:Incandescent lamps: This is the lowest-energy light source used in spectroscopy.
It is commonly used in UV-Vis spectrophotometers, but it has low luminosity and a short life span.Tungsten filament lamps: This is a higher-energy light source used in spectroscopy. They are more durable and longer-lasting than incandescent lamps, but they have a higher energy output than incandescent lamps.Deuterium lamps: This is a high-energy light source used in UV-Vis spectrophotometers.
They are useful for analyzing compounds in the UV range.Mercury lamps: This is the highest-energy light source used in spectroscopy. They are used for fluorescence spectroscopy because they produce a high-energy source of light that excites atoms and molecules.
To know more about light source visit :
https://brainly.com/question/31852805
#SPJ11
a lens has a refractive power of -1.50. what is its focal length?
It has been determined that the focal length of the lens is -0.6667 m.
Given: The refractive power of a lens is -1.50We are supposed to find the focal length of the given lens
Solution:The formula to find the focal length of a lens is given by:1/f = (n-1) (1/R1 - 1/R2)
Given: Refractive power (P) = -1.50
As we know that, P = 1/f (Where f is the focal length)
Hence, -1.50 = 1/fOr, f = -1/1.5= -0.6667 m
Therefore, the focal length of the given lens is -0.6667 m.
From the above calculations, it has been determined that the focal length of the lens is -0.6667 m.
To know more about focal length visit:
brainly.com/question/31755962
#SPJ11
what is the approximate thermal energy in kj/mol of molecules at 75 ° c?
Answer:
if you like it please do appreciate
To calculate the approximate thermal energy in kilojoules per mole (kJ/mol) of molecules at a given temperature, you can use the Boltzmann constant (k) and the ideal gas law.
The Boltzmann constant (k) is approximately equal to 8.314 J/(mol·K). To convert this to kilojoules per mole, we divide by 1000:
k = 8.314 J/(mol·K) = 0.008314 kJ/(mol·K)
Now, we need to convert the temperature to Kelvin (K) since the Boltzmann constant is defined in Kelvin. To convert from Celsius to Kelvin, we add 273.15 to the temperature:
T(K) = 75°C + 273.15 = 348.15 K
Finally, we can calculate the thermal energy using the formula:
Thermal energy = k * T
Thermal energy = 0.008314 kJ/(mol·K) * 348.15 K
Thermal energy ≈ 2.894 kJ/mol
Therefore, at 75°C, the approximate thermal energy of molecules is approximately 2.894 kilojoules per mole (kJ/mol).
The heat capacity of one mole of water is approximately 75.29/1000 = 0.07529 kj/mol. This value represents the approximate thermal energy in kj/mol of water molecules at 75 ° C.
Thermal energy refers to the energy present in a system that arises from the random movements of its atoms and molecules. When a body has a temperature of 75 ° C, it has a thermal energy that depends on the type of molecules in it and their specific heat capacity.
In this context, we will consider the thermal energy in kj/mol of molecules at 75 ° C.Let's use water as an example to calculate the approximate thermal energy in kj/mol of molecules at 75 ° C. The specific heat capacity of water is 4.18 J/g °C, and the molar mass of water is 18.01528 g/mol. Therefore, the thermal energy in kj/mol of water molecules at 75 ° C can be calculated as follows:ΔH = mcΔt, whereΔH = thermal energy,m = mass of the sample,c = specific heat capacity of the sample,Δt = change in temperature
To know more about heat capacity visit:-
https://brainly.com/question/28302909
#SPJ11
suggest how predictive mining techniques can be used by a sports team, using your favorite sport as an example
Predictive mining techniques involve examining the massive amount of data to uncover unknown patterns, potential relationships, and insights. In the sports sector, data mining can assist teams in making data-based decisions about things like player recruitment, game strategy, and injury prevention.
Data mining techniques can be utilized by a sports team to acquire a competitive edge. The team can gather relevant data on their competitors and their own players to figure out game trends and the possible outcomes of a game.
By mining sports data, a team can come up with strategies to overcome their opponents' weakness and maximize their strengths. As a result, predictive data mining can assist sports teams in enhancing their overall performance.
Predictive mining techniques can be used by a sports team to acquire a competitive edge and improve their overall performance. By mining sports data, a team can come up with strategies to overcome their opponents' weakness and maximize their strengths. With this information, teams can make data-based decisions about player recruitment, game strategy, and injury prevention. Therefore, predictive mining techniques provide an opportunity to enhance sports teams' performance.
To know more about Predictive mining techniques visit:
brainly.com/question/31967069
#SPJ11
An alpha particle (
4
He ) undergoes an elastic collision with a stationary uranium nucleus (
235
U). What percent of the kinetic energy of the alpha particle is transferred to the uranium nucleus? Assume the collision is one dimensional.
In an elastic collision between an alpha particle (4He) and a stationary uranium nucleus (235U), approximately 0.052% of the kinetic energy of the alpha particle is transferred to the uranium nucleus.
What percentage of the alpha particle's kinetic energy is transferred to the uranium nucleus in the elastic collision?In an elastic collision, both momentum and kinetic energy are conserved. Since the uranium nucleus is initially at rest, the total momentum before the collision is solely due to the alpha particle. After the collision, the alpha particle continues moving with a reduced velocity, while the uranium nucleus starts moving with a velocity. The conservation of kinetic energy dictates that the sum of the kinetic energies before and after the collision must be the same.
Due to the large mass of the uranium nucleus compared to the alpha particle, the alpha particle's velocity decreases significantly after the collision. Therefore, a small fraction of the initial kinetic energy is transferred to the uranium nucleus. Calculations show that approximately 0.052% of the alpha particle's kinetic energy is transferred to the uranium nucleus in this scenario.
Learn more about Elastic collisions
brainly.com/question/31318883
#SPJ11
what hall voltage (in mv) is produced by a 0.160 t field applied across a 2.60 cm diameter aorta when blood velocity is 59.0 cm/s?
A 0.160 t field applied across a 2.60 cm diameter aorta when blood velocity is 59.0 cm/s will give Hall voltage of 2.3712 mV.
For calculating this, we know that:
VH = B * d * v * RH
In this instance, the blood flow rate is given as 59.0 cm/s, the magnetic field strength is given as 0.160 T, the aorta diameter is given as 2.60 cm (which we will convert to metres, thus d = 0.026 m), and the magnetic field strength is given as 0.160 T.
Let's assume a value of RH = [tex]3.0 * 10^{-10} m^3/C.[/tex]
VH = (0.160 T) * (0.026 m) * (0.59 m/s) * [tex]3.0 * 10^{-10} m^3/C.[/tex]
VH = 0.0023712 V
Or,
VH = 2.3712 mV
Thus, the Hall voltage produced in the aorta is approximately 2.3712 mV.
For more details regarding Hall voltage, visit:
https://brainly.com/question/32048582
#SPJ4
What value below has 3 significant digits? a) 4.524(5) kev b) 1.48(4) Mev c) 58 counts d) 69.420 lols Q13: What is the correct count-rate limit of precision for an exactly 24 hour live time count with 4.00% dead time, a count rate of 40.89700 counts/second, and a Fano Factor of 0.1390000? a) 40.897(8) counts/sec b) 40.90(12) counts/sec c) 41.0(5) counts/sec d) 41(5) counts/sec e) Infinite Q14: What kind of detectors have the risk of a wall effect? a) Neutron gas detectors b) All gas detectors c) Neutron semiconductor detectors d) Gamma semiconductor detectors e) Geiger-Müller counters
The value below that has 3 significant digits is: c) 58 counts
In this value, the digits "5" and "8" are considered significant, and the trailing zero does not contribute to the significant figures. The value "58" has two significant digits.
Q13: The correct count-rate limit of precision for an exactly 24 hour live time count with 4.00% dead time, a count rate of 40.89700 counts/second, and a Fano Factor of 0.1390000 is:
b) 40.90(12) counts/sec
The value has 4 significant digits, and the uncertainty is indicated by the value in parentheses. The uncertainty is determined by the count rate's precision and the dead time effect.
Q14: The detectors that have the risk of a wall effect are:
c) Neutron semiconductor detectors
d) Gamma semiconductor detectors
The wall effect refers to the phenomenon where radiation interactions occur near the surface of a detector, leading to reduced sensitivity and accuracy. In the case of neutron and gamma semiconductor detectors, their thin semiconductor material can cause a significant portion of radiation interactions to occur close to the detector surface, resulting in the wall effect.
To know more about digits, visit
https://brainly.com/question/24491627
#SPJ11
The biggest coal burning power station in the world is in Taiwan with a power output capacity of 5500 MW. (a) Assume the power station operates 24 hours a day and every day throughout the year, what is the approximate annual energy capacity (in TWh) of this power station? (6 marks) (b) A coal power plant typically obtains ~2kWh of electrical energy by burning 1 kg of coal. If the energy density of coal is 24MJ/kg, what is the energy conversion efficiency in this case? (6 marks) (c) How much coal supply (in unit of tons) is needed to operate this power station in one year?
(a) The approximate annual energy capacity of the power station is 48,180 TWh. (b) The energy conversion efficiency is 8.3%. (c) The amount of coal supply needed is 24,090,000,000 tonnes.
For part (a), we used the formula for annual energy capacity which takes into account the power output, hours of operation, and days of operation per year. For part (b), we used the energy obtained from burning 1 kg of coal and the energy density of coal to calculate the energy conversion efficiency. We used the formula for energy conversion efficiency and found that it is 8.3%.
For part (c), we used the amount of energy generated in one year and the energy obtained from burning 1 kg of coal to calculate the amount of coal needed. We used the formula for amount of coal needed and found that it is 24,090,000,000 tonnes.
Learn more about power output here:
https://brainly.com/question/13937812
#SPJ11
Magnetic Field on the Axis of a Circular Current Loop Problem Consider a circular loop of wire of radius R located in the yz plane and carrying a steady current I as in Figure 30.6. Calculate the magnetic field at an axial point P a distance x from the center of the loop. Strategy In this situation, note that any element as is perpendicular to f. Thus, for any element, ld5* xf| (ds)(1)sin 90° = ds. Furthermore, all length elements around the loop are at the same distancer from P, where r2 = x2 + R2. = Figure 30.6 The geometry for calculating the magnetic field at a point P lying on the axis of a current loop. By symmetry, the total field is along this axis,
The net magnetic field on the axis of the circular current loop is given by B=(μ0IR2/2)(x2+R2)-3/2 This is the required expression for the magnitude of the magnetic field on the axis of a circular current loop at a point P which is at a distance x from the center of the loop.
Magnetic field on the axis of a circular current loop at point P which is at a distance x from the center of the loop is calculated by the Biot-Savart law. The magnetic field is given by [tex]B=(μ0/4π)∫dl×r/r3[/tex] where r is the distance between the current element and the point P.
Magnetic field direction is perpendicular to the plane of the loop on the axis of the loop. Let us now find the expression for the magnitude of magnetic field on the axis of a circular current loop.
The geometry for calculating the magnetic field at a point P lying on the axis of a current loop
Let us take the Cartesian coordinate system such that the center of the circular loop is at the origin O. Then the position vector of the current element is [tex]r’=Rcosθi+Rsinθj[/tex] and the position vector of the point P is [tex]r=xk[/tex].
Then the vector r’-r is given by r’-[tex]r=Rcosθi+Rsinθj-xk[/tex]
=(Rcosθi+Rsinθj-xk)
Now the magnitude of this vector is [tex]|r’-r|=√[(Rcosθ-x)2+(Rsinθ)2][/tex]
Then, the magnetic field dB due to this current element is given by [tex]dB=μ0/4π dl/r2[/tex]
where dl=I(r’dθ) is the current element. Now the vector dB can be expressed in terms of its x, y and z components as follows:
[tex]dB=μ0/4π dl/r2[/tex]
=μ0/4π I(r’dθ)/r2 (Rcosθi+Rsinθj-xk)/[R2+ x2 -2xRcosθ+R2sin2θ]
Taking the x-component of dB we get
dB Bx=μ0I[Rcosθ(R2+x2)-xR2cos2θ-R2x]/[4π(R2+ x2 -2xRcosθ+R2sin2θ)3/2]
Integrating the x-component of dB from θ=0 to θ=2π
we get
[tex]Bx=∫dBBx[/tex]
=∫μ0I[Rcosθ(R2+x2)-xR2cos2θ-R2x]/[4π(R2+ x2
-2xRcosθ+R2sin2θ)3/2]dθ=0
Therefore, the net magnetic field on the axis of the circular current loop is given by [tex]B=(μ0IR2/2)(x2+R2)-3/2[/tex]
This is the required expression for the magnitude of the magnetic field on the axis of a circular current loop at a point P which is at a distance x from the center of the loop.
To learn more about Magnetic visit;
https://brainly.com/question/3617233
#SPJ11
the winding of an ac electric motor has an inductance of 21 mh and a resistance of 13 ω. the motor runs on a 60-hz rms voltage of 120 v.
a) what is the rms current that the motor draws, in amperes?
b) by what angle, in degrees, does the current lag the input voltage?
c) what is the capacitance, in microfarads, of the capacitor that should be connected in series with the motor to cause the current to be in phase with the input voltage?
The capacitance, in microfarads, of the capacitor that should be connected in series with the motor to cause the current to be in phase with the input voltage is 0.33 µF.
a) We have L = 21 mH, R = 13 ω and V = 120 V
The rms current that the motor draws, in amperes is calculated as follows:Irms = V/Z
Where, [tex]Irms = V/Z[/tex]
L = Inductance = 21 m
H = 21 × 10⁻³H
f = 60 Hz
R = Resistance = 13 Ω
V = RMS voltage = 120 V
Reactance, [tex]X = 2πfL[/tex]
= 2 × 3.1415 × 60 × 21 × 10⁻³
= 7.92 Ω
Thus, Z = sqrt(R² + X²)
= sqrt(13² + 7.92²)
= 15.22 Ω And,
[tex]Irms = V/Z[/tex]
= 120/15.22
= 7.89 A
Therefore, the rms current that the motor draws, in amperes is 7.89 A.
b) The current lags the voltage by a phase angle, ϕ. This can be calculated as follows:
[tex]tan ϕ = X/R[/tex]
= 7.92/13
= 0.609
Thus, the angle is,
ϕ = tan⁻¹0.609
= 30.67⁰
Therefore, by 30.67 degrees does the current lag the input voltage.
c) The capacitor that should be connected in series with the motor to cause the current to be in phase with the input voltage is given by,
[tex]C = 1/(2πfX)[/tex]
Where, f = 60 Hz
X = 7.92 Ω
C = 1/(2 × 3.1415 × 60 × 7.92 × 10⁰)
= 0.33 µF
Thus, the capacitance, in microfarads, of the capacitor that should be connected in series with the motor to cause the current to be in phase with the input voltage is 0.33 µF.
To learn more about capacitance visit;
https://brainly.com/question/18271076
#SPJ11
A capacitor is discharged through a 20.0 Ω resistor. The discharge current decreases to 22.0% of its initial value in 1.50 ms.
What is the time constant (in ms) of the RC circuit?
a) 0.33 ms
b) 0.67 ms
c) 1.50 ms
d) 3.75 ms
The time constant (in ms) of the RC circuit is 3.75 ms. Hence, the correct option is (d) 3.75 ms.
The rate of decay of the current in a charging capacitor is proportional to the current in the circuit at that time. Therefore, it takes longer for a larger current to decay than for a smaller current to decay in a charging capacitor.A capacitor is discharged through a 20.0 Ω resistor.
The discharge current decreases to 22.0% of its initial value in 1.50 ms. We can obtain the time constant of the RC circuit using the following formula:$$I=I_{o} e^{-t / \tau}$$Where, I = instantaneous current Io = initial current t = time constant R = resistance of the circuit C = capacitance of the circuit
To know more about circuit visit:-
https://brainly.com/question/12608516
#SPJ11
The time constant of the RC circuit is approximately 0.674 m s.
To determine the time constant (τ) of an RC circuit, we can use the formula:
τ = RC
Given that the discharge current decreases to 22.0% of its initial value in 1.50 m s, we can calculate the time constant as follows:
The percentage of the initial current remaining after time t is given by the equation:
I(t) =[tex]I_oe^{(-t/\tau)[/tex]
Where:
I(t) = current at time t
I₀ = initial current
e = Euler's number (approximately 2.71828)
t = time
τ = time constant
We are given that the discharge current decreases to 22.0% of its initial value. Therefore, we can set up the following equation:
0.22 =[tex]e^{(-1.50/\tau)[/tex]
To solve for τ, we can take the natural logarithm (ln) of both sides:
ln(0.22) = [tex]\frac{-1.50}{\tau}[/tex]
Rearranging the equation to solve for τ:
τ = [tex]\frac{-1.50 }{ ln(0.22)}[/tex]
Calculating this expression:
τ ≈ 0.674 m s
Learn more about time constant here:
brainly.com/question/32577767
#SPJ11
Relative to the ground, a car has a velocity of 17.3 m/s, directed due north. Relative to this car, a truck has a velocity of 23.0 m/s, directed 52.0° north of east. What is the magnitude of the truc
The
magnitude
of the truck's velocity
is approximately 22.783 m/s.
To solve this problem, we can break down the velocities into their x and y components.
The
car's velocity
is directed due north, so its
x-component is 0 m/s and its y-component is 17.3 m/s.
The truck's velocity is directed 52.0° north of east. To find its x and y components, we can use trigonometry. Let's define the
angle
measured counterclockwise from the positive x-axis.
The x-component of the truck's velocity can be found using the cosine function:
cos(52.0°) = adjacent / hypotenuse
cos(52.0°) = x-component / 23.0 m/s
Solving for the x-component:
x-component = 23.0 m/s * cos(52.0°)
x-component ≈ 14.832 m/s
The y-component of the truck's velocity can be found using the sine function:
sin(52.0°) = opposite / hypotenuse
sin(52.0°) = y-component / 23.0 m/s
Solving for the y-component:
y-component = 23.0 m/s * sin(52.0°)
y-component ≈ 17.284 m/s
Now, we can find the magnitude of the truck's velocity by using the
Pythagorean theorem
:
magnitude = √(x-component² + y-component²)
magnitude = √((14.832 m/s)² + (17.284 m/s)²)
magnitude ≈ √(220.01 + 298.436)
magnitude ≈ √518.446
magnitude ≈ 22.783 m/s
Therefore, the magnitude of the truck's
velocity
is approximately 22.783 m/s.
To know more about
magnitude
visit:
https://brainly.com/question/30337362
#SPJ11
please fast.
- 14. A 0.400 kg physics cart is moving with a velocity of 0.22 m/s. This cart collides inelastically with a second stationary cart and the two move off together with a velocity of 0.16 m/s. What was
In an inelastic collision, two or more objects stick together and travel as one unit after the collision. The principle of conservation of momentum states that the total momentum of a closed system remains constant if no external forces act on the system, which is also true for an inelastic collision.
As a result, the momentum of the first cart is equal to the combined momentum of the two carts after the collision, since the collision is inelastic. The velocity of the two carts after the collision can be calculated using the conservation of momentum, as follows:0.400 kg x 0.22 m/s + 0 kg x 0 m/s = (0.400 kg + 0 kg) x 0.16 m/s0.088 Ns = 0.064 NsThe total momentum of the system is 0.064 Ns.
The two carts move together after the collision with a velocity of 0.16 m/s. The mass of the second cart is 0 kg, therefore, its initial momentum is 0 Ns. The momentum of the first cart is therefore equal to the total momentum of the system.
The initial momentum of the first cart can be calculated using the following formula:p = mv0.088 Ns = 0.400 kg x v Therefore, the initial velocity of the first cart is:v = p/mv = 0.088 Ns / 0.400 kgv = 0.22 m/s Hence, the initial velocity of the first cart is 0.22 m/s.
To know more about inelastic collision refer here:
https://brainly.com/question/14521843#
#SPJ11
A charge -5.5 nC is placed at (-3.1.-3) m and another charge 9.3 nC is placed at (-2,3,-2) m. What is the electric field at (1,0,0)m?
The electric field at (1,0,0) m due to the given charges is -1.2 x 10^5 N/C, directed towards the left.
Let's first calculate the electric field at point P due to the first charge:q1 = -5.5 nC, r1 = (-3.1, -3, 0) m and r = (1, 0, 0) m
The distance between charge 1 and point P is:r = √((x2 - x1)² + (y2 - y1)² + (z2 - z1)²)r = √((1 - (-3.1))² + (0 - (-3))² + (0 - 0)²)r = √(4.1² + 3² + 0²)r = 5.068 m
Therefore, the electric field at point P due to charge 1 is:
E1 = kq1 / r1²E1 = (9 x 10^9 Nm²/C²) x (-5.5 x 10^-9 C) / (5.068 m)²E1 = -4.3 x 10^5 N/C (towards left, as the charge is negative)
Now, let's calculate the electric field at point P due to the second charge:
q2 = 9.3 nC, r2 = (-2, 3, -2) m and r = (1, 0, 0) m
The distance between charge 2 and point P is:
r = √((x2 - x1)² + (y2 - y1)² + (z2 - z1)²)
r = √((1 - (-2))² + (0 - 3)² + (0 - (-2))²)
r = √(3² + 3² + 2²)r = √22 m
Therefore, the electric field at point P due to charge 2 is:
E2 = kq2 / r2²
E2 = (9 x 10^9 Nm²/C²) x (9.3 x 10^-9 C) / (√22 m)²
E2 = 3.1 x 10^5 N/C (towards right, as the charge is positive)
Now, the total electric field at point P due to both charges is:
E = E1 + E2
E = -4.3 x 10^5 N/C + 3.1 x 10^5 N/C
E = -1.2 x 10^5 N/C
Therefore, the electric field at (1,0,0) m due to the given charges is -1.2 x 10^5 N/C, directed towards the left.
Learn more about electric field at:
https://brainly.com/question/15906502
#SPJ11
The electric field at point P (1, 0, 0)m is (-2.42 × 10⁶) î + 6.91 × 10⁶ ĵ N/C.
The given charges are -5.5 nC and 9.3 nC. The position vectors of these charges are (-3.1, -3, 0)m and (-2, 3, -2)m. We need to find the electric field at (1, 0, 0)m.
Let's consider charge q1 (-5.5 nC) and charge q2 (9.3 nC) respectively with position vectors r1 and r2. Electric field due to q1 at point P (1,0,0)m is given by:r1 = (-3.1, -3, 0)mq1 = -5.5 nC
Position vector r from q1 to P = rP - r1 = (1, 0, 0)m - (-3.1, -3, 0)m = (4.1, 3, 0)m
Using the formula of electric field, the electric field due to q1 at point P will be given by:
E1 = kq1 / r²
where k is the Coulomb constantk = 9 × 10⁹ N m² C⁻²
Electric field due to q1 at point P isE1 = 9 × 10⁹ × (-5.5) / (4.1² + 3²) = -2.42 × 10⁶ N/C
Now, let's consider charge q2. The position vector of q2 is given by:r2 = (-2, 3, -2)mq2 = 9.3 nC
Position vector r from q2 to P = rP - r2 = (1, 0, 0)m - (-2, 3, -2)m = (3, -3, 2)m
Electric field due to q2 at point P will be given by:
E2 = kq2 / r²
Electric field due to q2 at point P is
E2 = 9 × 10⁹ × 9.3 / (3² + (-3)² + 2²) = 6.91 × 10⁶ N/C
Now, we can get the total electric field due to the given charges by adding the electric fields due to q1 and q2 vectorially.
The vector addition of electric fields E1 and E2 is given by the formula:
E = E1 + E2
Let's consider charge q1 (-5.5 nC) and charge q2 (9.3 nC) respectively with position vectors r1 and r2. Electric field due to q1 at point P (1,0,0)m is given by:r1 = (-3.1, -3, 0)mq1 = -5.5 nC
Position vector r from q1 to P = rP - r1 = (1, 0, 0)m - (-3.1, -3, 0)m = (4.1, 3, 0)m
Using the formula of electric field, the electric field due to q1 at point P will be given by:E1 = kq1 / r²
where k is the Coulomb constant
k = 9 × 10⁹ N m² C⁻²
The magnitude of the electric field due to q1 at point P is given by|E1| = 9 × 10⁹ × |q1| / r²= 9 × 10⁹ × 5.5 / (4.1² + 3²) N/C= 2.42 × 10⁶ N/C
The direction of the electric field due to q1 at point P is towards the charge q1.
Now, let's consider charge q2. The position vector of q2 is given by:r2 = (-2, 3, -2)mq2 = 9.3 nC
Position vector r from q2 to P = rP - r2 = (1, 0, 0)m - (-2, 3, -2)m = (3, -3, 2)m
The magnitude of the electric field due to q2 at point P will be given by:
E2 = kq2 / r²= 9 × 10⁹ × 9.3 / (3² + (-3)² + 2²) N/C= 6.91 × 10⁶ N/C
The direction of the electric field due to q2 at point P is away from the charge q2.
Now, we can get the total electric field due to the given charges by adding the electric fields due to q1 and q2 vectorially. The vector addition of electric fields E1 and E2 is given by the formula:E = E1 + E2E = (-2.42 × 10⁶) î + 6.91 × 10⁶ ĵ N/C
Learn more about electric field: https://brainly.com/question/30544719
#SPJ11
suppose the previous forecast was 30 units, actual demand was 50 units, and ∝ = 0.15; compute the new forecast using exponential smoothing.
By using the formula of exponential smoothing, we can get the new forecast. Hence, the new forecast using exponential smoothing is 33 units.
Given:
Previous forecast = 30 units
Actual demand = 50 unitsα = 0.15Formula used:
New forecast = α(actual demand) + (1 - α)(previous forecast)
New forecast = 0.15(50) + (1 - 0.15)(30)New forecast = 7.5 + 25.5
New forecast = 33 units
Therefore, the new forecast using exponential smoothing is 33 units.
In exponential smoothing, the new forecast is computed by using the actual demand and previous forecast. In this question, the previous forecast was 30 units and actual demand was 50 units, with α = 0.15. By using the formula of exponential smoothing, we can get the new forecast. Hence, the new forecast using exponential smoothing is 33 units.
To know more about New forecast visit:
brainly.com/question/31844712
#SPJ11
an object moves with constant speed of 16.1 m/s on a circular track of radius 100 m. what is the magnitude of the object's centripetal acceleration?
If an object moves with constant speed of 16.1 m/s on a circular track of radius 100 m, the magnitude of the object's centripetal acceleration is 2.59 m/s².
The object moves with constant speed of 16.1 m/s on a circular track of radius 100 m and we have to determine the magnitude of the object's centripetal acceleration. We know that the formula to find the magnitude of the object's centripetal acceleration is given by: ac = v²/r
Where, v = speed of the object r = radius of the circular track
Substituting the given values, we get: ac = v²/r ac = 16.1²/100ac = 259/100ac = 2.59 m/s²
Therefore, the magnitude of the object's centripetal acceleration is 2.59 m/s².
More on centripetal acceleration: https://brainly.com/question/17123770
#SPJ11
The displacement of a wave traveling in the negative y-direction
is D(y,t)=(9.0cm)sin(45y+70t+π)D(y,t)=(9.0cm)sin(45y+70t+π), where
y is in m and t is in s.
What is the frequency of this wave?
Wh
The displacement of a wave traveling in the negative y-direction depends on the amplitude and frequency of the wave.
The displacement of a wave traveling in the negative y-direction is a combination of factors. The first factor is the amplitude, which is the maximum distance that a particle moves from its rest position as a wave passes through it. The second factor is the frequency, which is the number of waves that pass a fixed point in a given amount of time. The displacement of a wave is given by the formula y = A sin(kx - ωt + ϕ), where A is the amplitude, k is the wave number, x is the position, ω is the angular frequency, t is the time, and ϕ is the phase constant. This formula shows that the displacement depends on the amplitude and frequency of the wave.
These variables have the same fundamental meaning for waves. In any case, it is useful to word the definitions in a more unambiguous manner that applies straightforwardly to waves: Amplitude is the distance between the wave's maximum displacement and its resting position. Frequency is the number of waves that pass by a particular point every second.
Know more about amplitude and frequency, here:
https://brainly.com/question/31863582
#SPJ11
why did the masses of the objects have to be very small to be able to get the objects very close to each other?
The masses of the objects have to be very small to be able to get the objects very close to each other because of the gravitational force.
Gravitational force is the force of attraction between any two objects with mass. It is an attractive force that acts between all objects with mass. The strength of the gravitational force depends on the masses of the objects involved and the distance between them. When the objects are close to each other, the gravitational force between them becomes stronger. If the masses of the objects are very large, the gravitational force between them becomes very strong. This means that it is very difficult to get the objects very close to each other because of the strong force of gravity. However, if the masses of the objects are very small, the gravitational force between them becomes very weak. This means that it is much easier to get the objects very close to each other because there is less gravitational force pushing them apart.
Gravitational force is one of the fundamental forces in nature. It is an attractive force that acts between any two objects with mass. The strength of the gravitational force depends on the masses of the objects involved and the distance between them. When the objects are close to each other, the gravitational force between them becomes stronger. If the masses of the objects are very large, the gravitational force between them becomes very strong. This means that it is very difficult to get the objects very close to each other because of the strong force of gravity. However, if the masses of the objects are very small, the gravitational force between them becomes very weak. This means that it is much easier to get the objects very close to each other because there is less gravitational force pushing them apart. In general, the strength of the gravitational force between two objects is given by the formula F = Gm1m2/r^2, where F is the force of gravity, G is the gravitational constant, m1 and m2 are the masses of the two objects, and r is the distance between them. As you can see from this formula, the strength of the gravitational force decreases as the distance between the objects increases.
To know more about gravitational force visit :-
https://brainly.com/question/32609171
#SPJ11
In your own words define the following term and state its
importance for hypothesis testing (2 points correct definition, 3
points correct importance for hypothesis testing).
Null Hypothesis
Sampling
Sampling is the process of selecting a subset of individuals or items from a larger population in order to gather information or make inferences about the whole population. This method allows researchers to collect data from a smaller group, which is more efficient and cost-effective than collecting data from the entire population.
Sampling is a crucial process in research because it helps ensure that the data collected is representative of the population and reduces the potential for bias. There are several types of sampling methods, including random sampling, stratified sampling, and convenience sampling. The choice of sampling method depends on the research question, the population being studied, and the resources available to the researcher. The accuracy of the data obtained from a sample depends on the sample size and the sampling method used. A larger sample size is generally more representative of the population and reduces the margin of error, while a smaller sample size may be more susceptible to sampling bias.
Know more about population, here:
https://brainly.com/question/15889243
#SPJ11
The A string on a violin has a fundamental frequency of 440 Hz . The length of the vibrating portion is 32 cm , and it has a mass of 0.40 g .
Under what tension must the string be placed? Express your answer using two significant figures. FT = nothing
The tension in the A string of the violin must be approximately 98 N. We can use the wave equation for the speed of a wave on a string
To determine the tension in the A string of the violin, we can use the wave equation for the speed of a wave on a string:
v = √(FT/μ)
where v is the velocity of the wave, FT is the tension in the string, and μ is the linear mass density of the string.
The linear mass density (μ) can be calculated by dividing the mass (m) of the string by its length (L):
μ = m/L
Substituting this value into the wave equation, we have:
v = √(FT/(m/L))
Since the fundamental frequency of the A string is given as 440 Hz, we can use the formula for the wave speed:
v = λf
where λ is the wavelength and f is the frequency. For the fundamental frequency, the wavelength is twice the length of the vibrating portion:
λ = 2L
Substituting this expression for λ into the wave speed equation, we have:
v = 2Lf
Now we can equate the expressions for the wave speed and solve for the tension (FT):
√(FT/(m/L)) = 2Lf
Squaring both sides of the equation and rearranging, we get:
FT = (4mL^2f^2)/L
Simplifying further, we have:
FT = 4mLf^2
Plugging in the given values:
FT = 4(0.40 g)(32 cm)(440 Hz)^2
Converting the mass to kilograms and the length to meters:
FT = 4(0.40 × 10^(-3) kg)(0.32 m)(440 Hz)^2
Calculating the tension:
FT ≈ 98 N
Therefore, the tension in the A string of the violin must be approximately 98 N.
To learn more about Tension click here
https://brainly.com/question/14294135
#SPJ11
A 20.0-kg cannon ball is fired from a cannon with a muzzle speed of 100 m/s at an angle of 20.0° with the horizontal. Use the conservation of energy principle to find the maximum height reached by ba
A 20.0 kg cannonball is fired from a cannon with a muzzle speed of 100 m/s at an angle of 20.0°. Using conservation of energy, the maximum height reached by the cannonball is approximately 510.2 meters.
A cannon ball weighing 20.0 kg is launched from a cannon with an initial velocity of 100 m/s at an angle of 20.0° above the horizontal.
To determine the maximum height reached by the cannonball using the conservation of energy principle, we consider the conversion of kinetic energy into gravitational potential energy.
Initially, the cannonball has only kinetic energy, given by the equation KE = (1/2)mv², where m is the mass and v is the velocity.
At the highest point of its trajectory, the cannonball has no vertical velocity, meaning it has no kinetic energy but possesses gravitational potential energy, given by the equation PE = mgh, where h is the height and g is the acceleration due to gravity (approximately 9.8 m/s²).
Using the conservation of energy, we equate the initial kinetic energy to the maximum potential energy:
(1/2)mv² = mgh
Canceling the mass and rearranging the equation, we find:
v²/2g = h
Plugging in the given values, we have:
(100²)/(2*9.8) = h
Simplifying the equation, we find:
h ≈ 510.2 m
Therefore, the maximum height reached by the cannonball is approximately 510.2 meters.
To know more about maximum height refer here:
https://brainly.com/question/30878848#
#SPJ11
