1. The ocean water collects back in the ocean.
2. Condensation is the process by which water vapor in the air is changed into liquid water. Condensation is crucial to the water cycle because it is responsible for the formation of clouds.
3. an excessive amount of water flowing from downslope along earths surface
4. A.Evaporation occurs when water is warmed by the sun.
5. The water returns into the ocean by the water cycle . It evaporates , then it condensates , then it participates ( Rains ) and then goes back into the ocean.
Hope this answer correct ✌️
An air-filled capacitor consists of two parallel plates, each with an area of 7.60 cm^2, separated by a distance of 1.70 mm. A 25.0-V potential difference is applied to these plates. Calculate: a. the electric field between the plates b. the surface charge density c. the capacitance d. the charge on each plate.
Answer:
(a) 1.47 x 10⁴ V/m
(b) 1.28 x 10⁻⁷C/m²
(c) 3.9 x 10⁻¹²F
(d) 9.75 x 10⁻¹¹C
Explanation:
(a) For a parallel plate capacitor, the electric field E between the plates is given by;
E = V / d -----------(i)
Where;
V = potential difference applied to the plates
d = distance between these plates
From the question;
V = 25.0V
d = 1.70mm = 0.0017m
Substitute these values into equation (i) as follows;
E = 25.0 / 0.0017
E = 1.47 x 10⁴ V/m
(c) The capacitance of the capacitor is given by
C = Aε₀ / d
Where
C = capacitance
A = Area of the plates = 7.60cm² = 0.00076m²
ε₀ = permittivity of free space = 8.85 x 10⁻¹²F/m
d = 1.70mm = 0.0017m
C = 0.00076 x 8.85 x 10⁻¹² / 0.0017
C = 3.9 x 10⁻¹²F
(d) The charge, Q, on each plate can be found as follows;
Q = C V
Q = 3.9 x 10⁻¹² x 25.0
Q = 9.75 x 10⁻¹¹C
Now since we have found other quantities, it is way easier to find the surface charge density.
(b) The surface charge density, σ, is the ratio of the charge Q on each plate to the area A of the plates. i.e
σ = Q / A
σ = 9.75 x 10⁻¹¹ / 0.00076
σ = 1.28 x 10⁻⁷C/m²
Two 1.0 nF capacitors are connected in series to a 1.5 V battery. Calculate the total energy stored by the capacitors.
Answer:
1.125×10⁻⁹ J
Explanation:
Applying,
E = 1/2CV²................... Equation 1
Where E = Energy stored in the capacitor, C = capacitance of the capacitor, V = Voltage of the battery.
Given; C = 1.0 nF, = 1.0×10⁻⁹ F, V = 1.5 V
Substitute into equation 1
E = 1/2(1.0×10⁻⁹×1.5²)
E = 1.125×10⁻⁹ J
Hence the energy stored by the capacitor is 1.125×10⁻⁹ J
A double-convex thin lens is made of glass with an index of refraction of 1.52. The radii of curvature of the faces of the lens are 60 cm and 72 cm. What is the focal length of the lens
Answer:
63 cm
Explanation:
Mathematically;
The focal length of a double convex lens is given as;
1/f = (n-1)[1/R1 + 1/R2]
where n is the refractive index of the medium given as 1.52
R1 and R2 represents radius of curvature which are given as 60cm and 72cm respectively.
Plugging these values into the equation, we have:
1/f = (1.52-1)[1/60 + 1/72)
1/f = 0.0158
f = 1/0.0158
f = 63.29cm which is approximately 63cm
3. What are the first steps that you should take if you are unable to get onto the Internet? (1 point)
O Check your router connections then restart your router.
O Plug the CPU to a power source and reboot the computer.
O Adjust the display properties and check the resolution.
Use the Control Panel to adjust the router settings.
Answer:
Check your router connections then restart your router.
Explanation:
Answer:
Check your router connections then restart your router.
Explanation:
Most internet access comes from routers so the problem is most likely the router.
A small omnidirectional stereo speaker produces waves in all directions that have an intensity of 8.00 at a distance of 4.00 from the speaker.
At what rate does this speaker produce energy?
What is the intensity of this sound 9.50 from the speaker?
What is the total amount of energy received each second by the walls (including windows and doors) of the room in which this speaker is located?
Answer:
A. We have that radius r = 4.00m intensity I = 8.00 W/m^
total power = power/ Area ( 4πr2)= 8.00 w/m^2( 4π ( 4.00 m)2=1607.68 W
b) I = total power/ 4πr2= 8.00 W/m2 ( 4.00 m/ 9.5 m)2= 1.418 W/m2
c) E = total power x time= 1607 . 68 W x 1s= 1607.68 J
An unstable particle at rest spontaneously breaks into two fragments of unequal mass. The mass of the first fragment is 3.00 10-28 kg, and that of the other is 1.86 10-27 kg. If the lighter fragment has a speed of 0.844c after the breakup, what is the speed of the heavier fragment
Answer: Speed = [tex]3.10^{-31}[/tex] m/s
Explanation: Like in classical physics, when external net force is zero, relativistic momentum is conserved, i.e.:
[tex]p_{f} = p_{i}[/tex]
Relativistic momentum is calculated as:
p = [tex]\frac{mu}{\sqrt{1-\frac{u^{2}}{c^{2}} } }[/tex]
where:
m is rest mass
u is velocity relative to an observer
c is light speed, which is constant (c=[tex]3.10^{8}[/tex]m/s)
Initial momentum is zero, then:
[tex]p_{f}[/tex] = 0
[tex]p_{1}-p_{2}[/tex] = 0
[tex]p_{1} = p_{2}[/tex]
To find speed of the heavier fragment:
[tex]\frac{mu_{1}}{\sqrt{1-\frac{u^{2}_{1}}{c^{2}} } }=\frac{mu_{2}}{\sqrt{1-\frac{u^{2}_{2}}{c^{2}} } }[/tex]
[tex]\frac{1.86.10^{-27}u_{1}}{\sqrt{1-\frac{u^{2}_{1}}{(3.10^{8})^{2}} } }=\frac{3.10^{-28}.0.844.3.10^{8}}{\sqrt{1-\frac{(0.844c)^{2}}{c^{2}} } }[/tex]
[tex]\frac{1.86.10^{-27}u_{1}}{\sqrt{1-\frac{u^{2}_{1}}{(3.10^{8})^{2}} } }=1.42.10^{-19}[/tex]
[tex]1.86.10^{-27}u_{1} = 1.42.10^{-19}.{\sqrt{1-\frac{u^{2}_{1}}{(3.10^{8})^{2}} } }[/tex]
[tex](1.86.10^{-27}u_{1})^{2} = (1.42.10^{-19}.{\sqrt{1-\frac{u^{2}_{1}}{(3.10^{8})^{2}} } })^{2}[/tex]
[tex]3.46.10^{-54}.u_{1}^{2} = 2.02.10^{-38}.(1-\frac{u_{1}^{2}}{9.10^{16}} )[/tex]
[tex]3.46.10^{-54}.u_{1}^{2} = 2.02.10^{-38} -[2.02.10^{-38}(\frac{u_{1}^{2}}{9.10^{16}} )][/tex]
[tex]3.46.10^{-54}.u_{1}^{2} = 2.02.10^{-38} -2.24.10^{-23}.u^{2}_{1}[/tex]
[tex]3.46.10^{-54}.u_{1}^{2}+2.24.10^{-23}.u^{2}_{1} = 2.02.10^{-38}[/tex]
[tex]2.24.10^{-23}.u^{2}_{1} = 2.02.10^{-38}[/tex]
[tex]u^{2}_{1} = \frac{2.02.10^{-38}}{2.24.10^{-23}}[/tex]
[tex]u_{1} = \sqrt{9.02.10^{-62}}[/tex]
[tex]u_{1} = 3.10^{-31}[/tex]
The speed of the heavier fragment is [tex]u_{1} = 3.10^{-31}[/tex]m/s.
Specific heat is a measurement of the amount of heat energy input required for one gram of a substance to increase its temperature by one degree Celsius. Solid lithium has a specific heat of 3.5 J/g·°C. This means that one gram of lithium requires 3.5 J of heat to increase 1°C. Plot the temperature of 1g of lithium after 3.5, 7, and 10.5 J of thermal energy are added.
Answer:
ΔT = 1ºC , 2ºCand 3ºC
Explanation:
In this exercise they indicate the specific heat of lithium
let's calculate the temperature increase as a function of the heat introduced
Q = m [tex]c_{e}[/tex] ΔT
ΔT = Q / m c_{e}
calculate
for Q = 3.5 J
ΔT = 3.5 / (1 3.5)
ΔT = 1ºC
For Q = 7.0 J
ΔT = 7 / (1 3.5)
ΔT = 2ºC
for Q = 10.5 J
ΔD = 10.5 / (1 3.5)
ΔT = 3ºC
we see that this is a straight line, see attached
A 750 gram grinding wheel 25.0 cm in diameter is in the shape of a uniform solid disk. (we can ignore the small hole at the center). when it is in use, it turns at a consant 220 rpm about an axle perpendicular to its face through its center. When the power switch is turned off, you observe that the wheel stops in 45.0 s with constant angular acceleration due to friction at the axle. What torque does friction exert while this wheel is slowing down?
Answer:
Torque = 0.012 N.m
Explanation:
We are given;
Mass of wheel;m = 750 g = 0.75 kg
Radius of wheel;r = 25 cm = 0.25 m
Final angular velocity; ω_f = 0
Initial angular velocity; ω_i = 220 rpm
Time taken;t = 45 seconds
Converting 220 rpm to rad/s we have;
220 × 2π/60 = 22π/3 rad/s
Equation of rotational motion is;
ω_f = ω_i + αt
Where α is angular acceleration
Making α the subject, we have;
α = (ω_f - ω_i)/t
α = (0 - 22π/3)/45
α = -0.512 rad/s²
The formula for the Moment of inertia is given as;
I = ½mr²
I = (1/2) × 0.75 × 0.25²
I = 0.0234375 kg.m²
Formula for torque is;
Torque = Iα
For α, we will take the absolute value as the negative sign denotes decrease in acceleration.
Thus;
Torque = 0.0234375 × 0.512
Torque = 0.012 N.m
A/An ____________________ is a small, flexible tube with a light and lens on the end that is used for examination. Question 96 options:
Answer:
"Endoscope" is the correct answer.
Explanation:
A surgical tool sometimes used visually to view the internal of either a body cavity or maybe even an empty organ like the lung, bladder, as well as stomach. There seems to be a solid or elastic tube filled with optics, a source of fiber-optic light, and sometimes even a sample, epidurals, suction tool, and perhaps other equipment for sample analysis or recovery.If the
refractive index of benzere is 2.419,
what is the speed of light in benzene?
Answer:
[tex]v=1.24\times 10^8\ m/s[/tex]
Explanation:
Given that,
The refractive index of benzene is 2.419
We need to find the speed of light in benzene. The ratio of speed of light in vacuum to the speed of light in the medium equals the refractive index. So,
[tex]n=\dfrac{c}{v}\\\\v=\dfrac{c}{n}\\\\v=\dfrac{3\times 10^8}{2.419}\\\\v=1.24\times 10^8\ m/s[/tex]
So, the speed of light in bezene is [tex]1.24\times 10^8\ m/s[/tex].
A car travels at 45 km/h. If the driver breaks 0.65 seconds after seeing the traffic light turn yellow, how far will the car continue to travel before it begins to slow?
Answer:
8.1 m
Explanation:
Convert km/h to m/s.
45 km/h × (1000 m/km) × (1 h / 3600 s) = 12.5 m/s
Distance = speed × time
d = (12.5 m/s) (0.65 s)
d = 8.125 m
If Superman really had x-ray vision at 0.12 nm wavelength and a 4.1 mm pupil diameter, at what maximum altitude could he distinguish villains from heroes, assuming that he needs to resolve points separated by 5.4 cm to do this?
Answer:
Maximum altitude to see(L) = 1.47 × 10⁶ m (Approx)
Explanation:
Given:
wavelength (λ) = 0.12 nm = 0.12 × 10⁻⁹ m
Pupil Diameter (d) = 4.1 mm = 4 × 10⁻³ m
Separation distance (D) = 5.4 cm = 0.054 m
Find:
Maximum altitude to see(L)
Computation:
Resolving power = 1.22(λ / d)
D / L = 1.22(λ / d)
0.054 / L = 1.22 [(0.12 × 10⁻⁹) / (4 × 10⁻³ m)]
0.054 / L = 1.22 [0.03 × 10⁻⁶]
L = 0.054 / 1.22 [0.03 × 10⁻⁶]
L = 0.054 / [0.0366 × 10⁻⁶]
L = 1.47 × 10⁶
Maximum altitude to see(L) = 1.47 × 10⁶ m (Approx)
Without actually calculating any logarithms, determine which of the following intervals the sound intensity level of a sound with intensity 3.66×10^−4W/m^2 falls within?
a. 30 and 40
b. 40 and 50
c. 50 and 60
d. 60 and 70
e. 70 and 80
f. 80 and 90
g. 90 and 100
Answer:
f. 80 and 90
Explanation:
1 x 10⁻¹² W/m² sound intensity falls within 0 sound level
1 x 10⁻¹¹ W/m² sound intensity falls within 10 sound level
1 x 10⁻¹⁰ W/m² sound intensity falls within 20 sound level
1 x 10⁻⁹ W/m² sound intensity falls within 30 sound level
1 x 10⁻⁸ W/m² sound intensity falls within 40 sound level
1 x 10⁻⁷ W/m² sound intensity falls within 50 sound level
1 x 10⁻⁶ W/m² sound intensity falls within 60 sound level
1 x 10⁻⁵ W/m² sound intensity falls within 70 sound level
1 x 10⁻⁴ W/m² sound intensity falls within 80 sound level
1 x 10⁻³ W/m² sound intensity falls within 90 sound level
Given sound intensity (3.66 x 10⁻⁴ W/m²) falls with 1 x 10⁻⁴ W/m² of intensity which is within 80 and 90 sound level.
f. 80 and 90
You're conducting an experiment on another planet. You drop a rock from a height of 1 m and it hits the ground 0.4 seconds later. What is acceleration due to gravity on the planet ?
Answer:
Here,
v (final velocity) = 0
u (initial velocity) = u
a = ?
s = 1m
t = 0.4s
using the first equation of motion,
0 = u + 0.4a
= -0.4a = u
using the second equation of motion:
1 = 0.4u + 0.08a
from the bold equation
1 = 0.4(-0.4a) + 0.08a
1 = -0.16a + 0.08a
1 = -0.08a
a = -1/0.08
a = -100/8
a = -12.5 m/s/s
please make me brainly, i am 1 brainly away from the next rank
UVC light used in sterilizers, has wavelengths between 100 to 280 nm. If a certain UVC wave has a wavelength of 142.9 nm, what is the energy of one of its photons in J
Answer:
The energy of one of its photons is 1.391 x 10⁻¹⁸ J
Explanation:
Given;
wavelength of the UVC light, λ = 142.9 nm = 142.9 x 10⁻⁹ m
The energy of one photon of the UVC light is given by;
E = hf
where;
h is Planck's constant = 6.626 x 10⁻³⁴ J/s
f is frequency of the light
f = c / λ
where;
c is speed of light = 3 x 10⁸ m/s
λ is wavelength
substitute in the value of f into the main equation;
E = hf
[tex]E = \frac{hc}{\lambda} \\\\E = \frac{6.626*10^{-34} *3*10^{8}}{142.9*10^{-9}} \\\\E = 1.391*10^{-18} \ J[/tex]
Therefore, the energy of one of its photons is 1.391 x 10⁻¹⁸ J
What happens to the deflection of the galvanometer needle (due to moving the magnet) when you increase the number of loops
Answer:
If the magnet is moved, the galvanometer needle will deflect, showing that current is flowing through the coil which will increase total induced electromotive force
Explanation:
galvanometer is an instrument that can detect and measure small current in an electrical circuit.
If the magnet is moved, the galvanometer needle will deflect, showing that current is flowing through the coil. If it is move in a way into the coil,the needle deflect in that way and if it move in another way, it will deflect in the other way.
The total induced emf is equal to the emf induced in each loop by the changing magnetic flux, then multiplied by the number of loops and an increase in the number of loops will cause increase in the total induced emf.
In the lab, you shoot an electron towards the south. As it moves through a magnetic field, you observe the electron curving upward toward the roof of the lab. You deduce that the magnetic field must be pointing:_______.
a. to the west.
b. upward.
c. to the north.
d. to the east.
e. downward.
Answer:
a. to the west.
Explanation:
An electron in a magnetic field always experience a force that tends to change its direction of motion through the magnetic field. According to Lorentz left hand rule (which is the opposite of Lorentz right hand rule for a positive charge), the left hand is used to represent the motion of an electron in a magnetic field. Hold out the left hand with the fingers held out parallel to the palm, and the thumb held at right angle to the other fingers. If the thumb represents the motion of the electron though the field, and the other fingers represent the direction of the field, then the palm will push in the direction of the force on the particle.
In this case, if we point the thumb (which shows the direction we shot the electron) to the south (towards your body), with the palm (shows the direction of the force) facing up to the roof, then the fingers (the direction of the field) will point west.
The linear density rho in a rod 3 m long is 8/ x + 1 kg/m, where x is measured in meters from one end of the rod. Find the average density rhoave of the rod.
Answer:
The average density of the rod is 1.605 kg/m.
Explanation:
The average density of the rod is given by:
[tex] \rho = \frac{m}{l} [/tex]
To find the average density we need to integrate the linear density from x₁ = 0 to x₂ = 3, as follows:
[tex] \int_{0}^{3} \frac{8}{3(x + 1)}dx [/tex]
[tex] \rho = \frac{8}{3} \int_{0}^{3} \frac{1}{(x + 1)}dx [/tex] (1)
Using u = x+1 → du = dx → u₁= x₁+1 = 0+1 = 1 and u₂ = x₂+1 = 3+1 = 4
By entering the values above into (1), we have:
[tex] \rho = \frac{8}{3} \int_{0}^{3} \frac{1}{u}du [/tex]
[tex]\rho = \frac{8}{3}*log(u)|_{1}^{4} = \frac{8}{3}[log(4) - log(1)] = 1.605 kg/m[/tex]
Therefore, the average density of the rod is 1.605 kg/m.
I hope it helps you!
The average density of the rod is [tex]1.605 \;\rm kg/m^{3}[/tex].
Given data:
The length of rod is, L = 3 m.
The linear density of rod is, [tex]\rho=\dfrac{8}{x+1} \;\rm kg/m[/tex].
To find the average density we need to integrate the linear density from x₁ = 0 to x₂ = 3, The expression for the average density is given as,
[tex]\rho' = \int\limits^3_0 { \rho} \, dx\\\\\\\rho' = \int\limits^3_0 { \dfrac{m}{L}} \, dx\\\\\\\rho' = \int\limits^3_0 {\dfrac{8}{3(x+1)}} \, dx[/tex]............................................................(1)
Using u = x+1
du = dx
u₁= x₁+1 = 0+1 = 1
and
u₂ = x₂+1 = 3+1 = 4
By entering the values above into (1), we have:
[tex]\rho' =\dfrac{8}{3} \int\limits^3_0 {\dfrac{1}{u}} \, du\\\\\\\rho' =\dfrac{8}{3} \times [log(u)]^{4}_{1}\\\\\\\rho' =\dfrac{8}{3} \times [log(4)-log(1)]\\\\\\\rho' =1.605 \;\rm kg/m^{3}[/tex]
Thus, we can conclude that the average density of the rod is [tex]1.605 \;\rm kg/m^{3}[/tex].
Learn more about the average density here:
https://brainly.com/question/1371999
Matter's resistance to a change in motion is called _____ and is directly proportional to the mass of an object
Answer:
Matter's resistance to a change in motion is called INERTIA and is directly proportional to the mass of an object.
Explanation:
The sun generates both mechanical and electromagnetic waves. Which statement about those waves is true?
OA. The mechanical waves reach Earth, while the electromagnetic waves do not.
OB. The electromagnetic waves reach Earth, while the mechanical waves do not.
OC. Both the mechanical waves and the electromagnetic waves reach Earth.
OD. Neither the mechanical waves nor the electromagnetic waves reach Earth.
Answer: The correct answer for this question is letter (B) The electromagnetic waves reach Earth, while the mechanical waves do not. The sun generates both mechanical and electromagnetic waves. Space, between the sun and the earth is a nearly vacuum. So mechanical wave can not spread out in the vacuum.
Hope this helps!
Answer:
The electromagnetic waves reach Earth, while the mechanical waves do not
(a) Determine the capacitance of a Teflon-filled parallel-plate capacitor having a plate area of 1.80 cm2 and a plate separation of 0.010 0 mm.
pF
(b) Determine the maximum potential difference that can be applied to a Teflon-filled parallel-plate capacitor having a plate area of 1.80 cm2 and a plate separation of 0.010 0 mm.
kV
Explanation:
(a) Given that,
Area of a parallel plate capacitor, [tex]A=1.8\ cm^2=1.8\times 10^{-4}\ m^2[/tex]
The separation between the plates of a capacitor, [tex]d=0.01\ mm = 10^{-5}\ m[/tex]
The dielectric constant of, k = 2.1
When a dielectric constant is inserted between parallel plate capacitor, the capacitance is given by :
[tex]C=\dfrac{k\epsilon_o A}{d}[/tex]
Putting all the values we get :
[tex]C=\dfrac{2.1\times 8.85\times 10^{-12}\times 1.8\times 10^{-4}}{0.01\times 10^{-3}}\\\\C=3.345\times 10^{-10}\ F\\\\C=334.5\ pF[/tex]
(b) We know that the Teflon has dielectric strength of 60 MV/m, [tex]E=60\times 10^6\ V/m[/tex]
The voltage difference between the plates at this critical voltage is given by :
[tex]V=Ed\\\\V=60\times 10^6\times 0.01\times 10^{-3} \\\\V=600\ V[/tex]
or
V = 0.6 kV
We have that the Capacitance and potential difference is mathematically given as
[tex]Vmax=\frac{Q}{334.68pF}[/tex]C=334.68pF
Capacitance &potential differenceQuestion Parameters:
having a plate area of 1.80 cm2 and a plate separation of 0.010 0 mm
having a plate area of 1.80 cm2 and a plate separation of 0.010 0 mm.
a)
Generally the equation for the Capacitance is mathematically given as
[tex]C=\frac{ke_0A}{d}\\\\Therefore\\\\C=\frac{2.1*1.80e-4*8.85e12}{0.01e-3}\\\\[/tex]
C=334.68pF
b)
Generally the equation for the Capacitance is mathematically given as
[tex]Vmax=\frac{Q}{C}[/tex]
Where
Q is the charge on the plates, and hence not given
Therefore, maximum potential difference is
[tex]Vmax=\frac{Q}{334.68pF}[/tex]
For more information on potential difference visit
https://brainly.com/question/14883923
A ball is thrown upward from a height of 432 feet above the ground, with an initial velocity of 96 feet per second. From physics it is known that the velocity at time t is v (t )equals 96 minus 32 t feet per second. a) Find s(t), the function giving the height of the ball at time t. b) How long will the ball take to reach the ground? c) How high will the ball go?
Answer;
A)S(t)=96t-16t² +432
B)it will take 9 seconds for the ball to reach the ground.
C)864feet
Explanation:
We were given an initial height of 432 feet.
And v(t)= 96-32t
A) we are to Find s(t), the function giving the height of the ball at time t
The position, or heigth, is the integrative of the velocity. So
S(t)= ∫(96-32)dt
S(t)=96t-16t² +K
S(t)=96t-16t² +432
In which the constant of integration K is the initial height, so K= 432
b) we need to know how long will the ball take to reach the ground
This is t when S(t)= 0
S(t)=96t-16t² +432
-16t² +96t +432=0
This is quadratic equation, if you solve using factorization method we have
t= -3 or t= 9
Therefore, , t is the instant of time and it must be a positive value.
So it will take 9 seconds for the ball to reach the ground.
C)V=s/t
Velocity= distance/ time
=96=s/9sec
S=96×9
=864feet
By applying the integrations,
(a) [tex]S = 96t-16t^2+432[/tex]
(b) Time will be "t = 9".
(c) Height will be "576"
Given:
Height,
423 feetInitial velocity,
96 feet/secAccording to the question,
(a)
Integrate v:
[tex]S = 96t-16t^2+C[/tex]Initial Condition,
→ [tex]S = 96t-16t^2+432[/tex]
(b)
Hits the ground when,
S = 0→ [tex]0=96t-16t^2+432[/tex]
→ [tex]t =9[/tex]
(c)
Maximum height when,
v = 0→ [tex]0 = 96-32 t[/tex]
→ [tex]t = 3[/tex]
Now,
→ [tex]S = 96\times 3-16\times 3^2+432[/tex]
[tex]= 576[/tex]
Thus the answer above is correct.
Learn more:
https://brainly.com/question/16105731
A load of 1 kW takes a current of 5 A from a 230 V supply. Calculate the power factor.
Answer:
Power factor = 0.87 (Approx)
Explanation:
Given:
Load = 1 Kw = 1000 watt
Current (I) = 5 A
Supply (V) = 230 V
Find:
Power factor.
Computation:
Power factor = watts / (V)(I)
Power factor = 1,000 / (230)(5)
Power factor = 1,000 / (1,150)
Power factor = 0.8695
Power factor = 0.87 (Approx)
A wire of 5.8m long, 2mm diameter carries 750ma current when 22mv potential difference is applied at its ends. if drift speed of electrons is found then:_________.
(a) The resistance R of the wire(b) The resistivity p, and(c) The number n of free electrons per unit volume.
Explanation:
According to Ohms Law :
V = I * R
(A) R (Resistance) = 0.022 / 0.75 = 0.03 Ohms
Also,
[tex]r = \alpha \frac{length}{area} = \alpha \frac{5.8}{3.14 \times 0.001 \times 0.001} [/tex]
(B)
[tex] \alpha(resistivity) = 1.62 \times {10}^{ - 8} [/tex]
Drift speed is missing. It is given as;
1.7 × 10^(-5) m/s
A) R = 0.0293 ohms
B) ρ = 1.589 × 10^(-8)
C) n = 8.8 × 10^(28) electrons
This is about finding, resistance and resistivity.
We are given;Length; L = 5.8 m
Diameter; d = 2mm = 0.002 m
Radius; r = d/2 = 0.001 m
Voltage; V = 22 mv = 0.022 V
Current; I = 750 mA = 0.75 A
Area; A = πr² = 0.001²π
Drift speed; v_d = 1.7 × 10^(-5) m/s
A) Formula for resistance is;R = V/I
R = 0.022/0.75
R = 0.0293 ohms
B) formula for resistivity is given by;ρ = RA/L
ρ = (0.0293 × 0.001²π)/5.8
ρ = 1.589 × 10^(-8)
C) Formula for current density is given by;J = n•e•v_d
Where;
J = I/A = 0.75/0.001²π A/m² = 238732.44 A/m²
e is charge on an electron = 1.6 × 10^(-19) C
v_d = 1.7 × 10^(-5) m/s
n is number of free electrons per unit volume
Thus;
238732.44 = n(1.6 × 10^(-19) × 1.7 × 10^(-5))
238732.44 = (2.72 × 10^(-24))n
n = 238732.44/(2.72 × 10^(-24))
n = 8.8 × 10^(28)
Read more at; brainly.com/question/17005119
A 70 kg man floats in freshwater with 3.2% of his volume above water when his lungs are empty, and 4.85% of his volume above water when his lungs are full.
Required:
a. Calculate the volume of air he inhales - called his lung capacity - in liters.
b. Does this lung volume seem reasonable?
Answer:
Explanation:
A) Vair = 1.3 L
B) Volume is not reasonable
Explanation:
A)
Assume
m to be total mass of the man
mp be the mass of the man that pulled out of the water
m1 be the mass above the water with the empty lung
m2 be the mass above the water with full lung
wp be the weight that the buoyant force opposes as a result of the air.
Va be the volume of air inside man's lungs
Fb be the buoyant force due to the air in the lung
given;
m = 78.5 kg
m1 = 3.2% × 78.5 = 2.5 kg
m2 = 4.85% × 78.5 = 3.8kg
But, mp = m2- m1
mp = 3.8 - 2.5
mp = 1.3kg
So using
Archimedes principle, the relation for formula for buoyant force as;
Fb = (m_displaced water)g = (ρ_water × V_air × g)
Where ρ_water is density of water = 1000 kg/m³
Thus;
Fb = wp = 1.3× 9.81
Fb = 12.7N
But
Fb = (ρ_water × V_air × g)
So
Vair = Fb/(ρ_water × × g)
Vair = 12.7/(1000 × 9.81)
V_air = 1.3 × 10^(-3) m³
convert to litres
1 m³ = 1000 L
Thus;
V_air = 1.3× 10^(-3) × 1000
V_air = 1.3 L
But since the average lung capacity of an adult human being is about 6-7litres of air.
Thus, the calculated lung volume is not reasonable
Explanation:
If one could transport a simple pendulum of constant length from the Earth's surface to the Moon's, where acceleration due to gravity is one-sixth (1/6) that on the Earth, by what factor would be the pendulum frequency be changed
Answer:
The frequency will change by a factor of 0.4
Explanation:
T = 2(pi)*sqrt(L/g)
Since g(moon) = (1/6)g(earth), the period would change by sqrt[1/(1/6)] = sqrt(6) ~ 2.5 times longer on the moon. Since the period & frequency are inverses, the frequency would be 1/2.5 or 0.4 times shorter on the moon.
1. (I) If the magnetic field in a traveling EM wave has a peak magnitude of 17.5 nT at a given point, what is the peak magnitude of the electric field
Answer:
The electric field is [tex]E = 5.25 V/m[/tex]
Explanation:
From the question we are told that
The peak magnitude of the magnetic field is [tex]B = 17.5 nT = 17.5 *10^{-9}\ T[/tex]
Generally the peak magnitude of the electric field is mathematically represented as
[tex]E = c * B[/tex]
Where c is the speed of light with value [tex]c = 3.0 *10^{8} \ m/s[/tex]
So
[tex]E = 3.0 *10^{8} * 17.5 *10^{-9}[/tex]
[tex]E = 5.25 V/m[/tex]
The peak magnitude of the electric field will be "5.25 V/m".
Magnetic fieldAccording to the question,
Magnetic field's peak magnitude, B = 17.5 nT or,
= 17.5 × 10⁻⁹ T
Speed of light, c = 3.0 × 10⁸ m/s
We know the relation,
→ E = c × B
By substituting the values, we get
= 3.0 × 10⁸ × 17.5 × 10⁻⁹
= 5.25 V/m
Thus the above approach is appropriate.
Find out more information about magnetic field here:
https://brainly.com/question/26257705
light of wavelength 550 nm is incident on a diffraction grating that is 1 cm wide and has 1000 slits. What is the dispersion of the m = 2 line?
Answer:
The dispersion is [tex]D = 2.01220 *10^{5} \ rad/m[/tex]
Explanation:
From the question we are told that
The wavelength of the light is [tex]\lambda = 550 \ = 550 *10^{-9} \ n[/tex]
The width of the grating is[tex]k = 1\ cm = 0.01 \ m[/tex]
The number of slit is N = 1000 slits
The order of the maxima is m = 2
Generally the spacing between the slit is mathematically represented as
[tex]d = \frac{k}{N}[/tex]
substituting values
[tex]d = \frac{ 0.01}{1000}[/tex]
[tex]d = 1.0 *10^{-5} \ m[/tex]
Generally the condition for constructive interference is
[tex]d\ sin(\theta ) = m * \lambda[/tex]
substituting values
[tex]1.0 *10^{-5} sin (\theta) = 2 * 550 *10^{-9}[/tex]
[tex]\theta = sin^{-1} [\frac{ 2 * 550 *10^{-9}}{ 1.0 *10^{-5}} ][/tex]
[tex]\theta = 6.315^o[/tex]
Generally the dispersion is mathematically represented as
[tex]D = \frac{ m }{d cos(\theta )}[/tex]
substituting values
[tex]D = \frac{ 2 }{ 1.0 *10^{-5} cos(6.315 )}[/tex]
[tex]D = 2.01220 *10^{5} \ rad/m[/tex]
When a mercury thermometer is heated, the mercury expands and rises in the thin tube of glass. What does this indicate about the relative rates of expansion for mercury and glass
Answer:
This means that mercury has a higher or faster expansion rate than glass
Explanation:
This is because When a container expands, the reservoir in the glass expands at the same rate as the glass. Thus, if there is something in a glass and both expand at the same rate, they have no change - but if the contents expand faster, they will fill the container to a higher level, and if the contents expand slower, they will fill the container to a lower level (relative to the new size of the container).
a transformer changes 95 v acorss the primary to 875 V acorss the secondary. If the primmary coil has 450 turns how many turns does the seconday have g
Answer:
The number of turns in the secondary coil is 4145 turns
Explanation:
Given;
the induced emf on the primary coil, [tex]E_p[/tex] = 95 V
the induced emf on the secondary coil, [tex]E_s[/tex] = 875 V
the number of turns in the primary coil, [tex]N_p[/tex] = 450 turns
the number of turns in the secondary coil, [tex]N_s[/tex] = ?
The number of turns in the secondary coil is calculated as;
[tex]\frac{N_p}{N_s} = \frac{E_p}{E_s}[/tex]
[tex]N_s = \frac{N_pE_s}{E_p} \\\\N_s = \frac{450*875}{95} \\\\N_s = 4145 \ turns[/tex]
Therefore, the number of turns in the secondary coil is 4145 turns.
