Answer: The oxygen gas has a pressure of 4 atm if my volume decreases to 1 L.
Explanation:
Given: [tex]V_{1}[/tex] = 2 L, [tex]P_{1}[/tex] = 2 atm
[tex]V_{2}[/tex] = 1 L, [tex]P_{2}[/tex] = ?
Formula used to calculate the new pressure is as follows.
[tex]P_{1}V_{1} = P_{2}V_{2}[/tex]
Substitute the values into above formula as follows.
[tex]P_{1}V_{1} = P_{2}V_{2}\\2 atm \times 2 L = P_{2} \times 1 L\\P_{2} = 4 atm[/tex]
Thus, we can conclude that the oxygen gas has a pressure of 4 atm if my volume decreases to 1 L.
What type of nuclear decay is shown by the reaction below?
A. Alpha
B. Gamma
C. Beta
O D. Fission
Answer:
C. Beta
Explanation:
Which reaction occurs at the cathode of a galvanic cell that has an aluminum electrode in an electrolyte with aluminum ions and copper electrode in an electrolyte with copper ions ? The reduction potential for the reduction of Cu^ 2+ = 0.34 The reduction potential for the reduction of AP^ 3+ =-1.68V.
Answer:
[tex]{ \bf{Cu {}^{2 + } + 2e \: → \: Cu }}[/tex]
The reaction that occurs at the cathode of a given galvanic cell is:
Cu²⁺ + 2e⁻ → Cu
What is Galvanic Cell?A galvanic cell can be defined as an electrochemical cell that converts the chemical energy of spontaneous redox reactions into electrical energy. The galvanic cell makes use of chemical reactions to generate electrical energy.
A galvanic cell consists of two half-cells and a salt bridge. Each half-cell further contains an electrode dipped into an electrolyte. When both electrodes are dipped in the same electrolyte, then there is no need for a salt bridge.
At the anode, an oxidation reaction occurs at this electrode. At the cathode, reduction occurs at this electrode. The anode has a negative potential with respect to the solution while the cathode has a positive potential with respect to the solution.
As in the question, the reduction of Cu²⁺ has a positive reduction potential. Therefore, the reduction of the copper will occur at the cathode.
Learn more about Galvanic cell, here:
https://brainly.com/question/13031093
#SPJ5
Increasing the concentration increases the speed of reaction by... increasing the number of collisions between products increasing the amount of energy in the system increasing the number of collisions between reactants lowering the activation energy of the reaction
Answer: increasing the number of collisions between reactants
Explanation:
A reaction is possible due to collisions between the reactants to create products. If we increase the concentration of reactants then that means that we are increasing the molecules of the reactants which would give them more chances to collide and make products.
For instance, using a non-chemistry example, if there are few cars in a large city, the accidents there will be less because the cars will have such space that they wouldn't collide with each other. If the number of cars in the city is increased however, there is now less space and more chances for cars to collide.
According to the kinetic-molecular theory, the average kinetic energy of gas particles depends on which factor?
Answer:
Temperature.
Explanation:
Kinetic molecular theory of gases states that gas particles exhibit a perfectly elastic collision and are constantly in motion.
According to the kinetic-molecular theory, the average kinetic energy of gas particles depends on temperature.
This ultimately implies that, the average kinetic energy of gas particles is directly proportional to the absolute temperature of an ideal gas. Thus, an increase in the average kinetic energy of gas particles would cause an increase in the absolute temperature of an ideal gas.
Temperature can be defined as a measure of the degree of coldness or hotness of a physical object. It is measured with a thermometer and its units are Celsius (°C), Kelvin (K) and Fahrenheit (°F).
What is a reaction rate
Answer:
Explanation:
A reaction rate is the measure of the change in concentration of the disappearance of reactants or the change in concentration of the appearance of products per unit time
Which diagram shows how the covalent bonds most likely form in a phosphorous trichloride molecule?
The first diagram shows the covalent bonds most likely form in a phosphorous trichloride molecule. Hence, option A is correct.
What is a covalent bond?Covalent bonds can be polar or nonpolar depending on the electronegativity difference between the atoms involved. In a nonpolar covalent bond, the electrons are shared equally between the atoms. In a polar covalent bond, the electrons are shared unequally.
Phosphorus trichloride (PCl₃) is a covalent compound that consists of one phosphorus atom and three chlorine atoms. The three chlorine atoms are located in a plane that is perpendicular to the phosphorus atom, forming an equilateral triangle with bond angles of 120°.
The molecule has a trigonal pyramidal shape, with the phosphorus atom at the apex and the three chlorine atoms at the base of the pyramid. The fourth hybridized orbital of phosphorus contains a lone pair of electrons that is located above the trigonal plane, giving the molecule a distorted tetrahedral geometry.
Thus, option A is correct.
To learn more about the covalent bond, follow the link:
https://brainly.com/question/10777799
#SPJ2
Explain and describe how the photoelectric effect occurs on an atomic level in terms of protons, neutrons, and electrons
ANSWER:
Explaining the experiments on the photoelectric effect. How these experiments led to the idea if light behaving as a particle of energy called a photon.
If 3.02 g of CuNO3 is dissolved in water to make a 0.560 M solution, what is the volume of the solution in milliliters?
Answer: The volume of the solution is 28.75 mL
Explanation:
Molarity is defined as the amount of solute expressed in the number of moles present per liter of solution. The units of molarity are mol/L. The formula used to calculate molarity:
[tex]\text{Molarity of solution}=\frac{\text{Given mass of solute}\times 1000}{\text{Molar mass of solute}\times \text{Volume of solution (mL)}}[/tex] .....(1)
Given values:
Molarity of copper nitrate = 0.560 M
Given mass of copper nitrate = 3.02 g
Molar mass of copper nitrate = 187.56 g/mol
Putting values in equation 1, we get:
[tex]0.560=\frac{3.02\times 1000}{187.56\times \text{Volume of solution}}\\\\\text{Volume of solution}=\frac{3.02\times 1000}{187.56\times 0.560}=28.75mL[/tex]
Hence, the volume of the solution is 28.75 mL
Question 24 Multiple Choice Worth 2 points)
[BWS.02] Why is science important for society?
Answer:
Because the scientific knowledge itself helps solve many basic human needs and it also improves how humans live and their standards. For example, without science medications wouldn´t exist and many technological devices we use now-a-days. We´re surrounded by science, we just don´t really notice it.
Se trata 50 g de aluminio que posee 10% de impurezas con suficiente cantidad de ácido sulfúrico ¿qué peso de sulfato de aluminio se obtiene si el porcentaje de rendimiento fue de 70%? P.A. (uma): Al: 27, S = 32, O = 16
Respuesta:
199.5 g
Explicación:
Paso 1: Escribir la reacción balanceada
2 Al + 3 H₂SO₄ ⇒ Al₂(SO₄)₃ + 3 H₂
Paso 2: Calcular la masa pura de 50 g de Al
Aluminio tiene 10% de impurezas, es decir, 10% de 50 g = 5 g. Luego, tiene 50 g - 5 g = 45 g de Al puro.
Paso 3: Calcular la masa teórica de Al₂(SO₄)₃ obtenida a partir de 45 g de Al
La relación de masas de Al₂(SO₄)₃ a Al es 342:54.
45 g Al × 342 g Al₂(SO₄)₃/54 g Al = 285 g Al₂(SO₄)₃
Paso 4: Calcular la masa real de Al₂(SO₄)₃ obtenida
El rendimiento de la reacción es de 70%.
285 g × 70% = 199.5 g
Why is sodium an active metal
Answer:
Sodium is very reactive in nature. When exposed in air, it automatically forms Na2O. When it is put in water it reacts vigorously and starts burning on water. Due to the above reasons Sodium is called an active metal
Explanation: hope this helps pls mark as brainliest ty
Which of the following acids has a basicity of 2?
1 point
ethanoic acid
hydrochloric acid
nitric acid
sulphuric acid
Answer:
its answer is nitric acid...
this may help you...The values used in the scale of pH and pOH are derived from a system designed by ______.
Curie
Gordonsen
Dalton
Sorenson
is it true that the most reactive metals are quite plentiful in the Earth's crust?
Answer:
yes
Explanation:
as it had got crushed down in the dinosaurs age
The ksp of StS04 is 3.2x10-7 What is the equilibrium concentration of sulfate lon a 1.0-L solution of strontium sulfate to which 0.10 mol of Sr(CH3CO2)2 has been added?
Answer:ehwusvudhwdvwxkwvbxbwxbxiwhxjvwxjvxwjxvjxvwxiwvxiwzgiwxvwjsbwis
HOPE IT HELPS IF YOU LIKE MY ANSWER THEN MARK ME AS BRAINLIEST ;-);-)
Which reaction will most likely take place based on the activity series? Li > K Ba CaNa > Mn > Zn > Cr> Fe> Cd Ni > H > Sb > Cu > Ag > Pd > Hg > Pt a. Ag+FeCl 3 b, Zn + CaO C. Ba+Na 2 CO 3 d . Cr+KNO3
Answer:
Among the given reactions,
a. Ag+FeCl 3
b, Zn + CaO
C. Ba+Na 2 CO 3
d . Cr+KNO3
which reaction is likely to take place based on the reactivity series?
Explanation:
The metal reactivity series is:
Li > K> Ba >Ca>Na > Mn > Zn > Cr> Fe> Cd Ni > H > Sb > Cu > Ag > Pd > Hg > Pt
The highly reactive metal will displace the less reactive metal from its compound during a displacement reaction.
a. Ag+FeCl 3
Ag is less reactive than Fe, so Ag cannot displace Fe from its compound.
This reaction also does not occur.
b, Zn + CaO
Zn is less reactive than Ca, so it cannot displace Ca from its compound.
This reaction does not occur.
C. Ba+Na 2 CO 3
Ba is more reactive than Na, so Ba displaces Na from its compound.
This reaction is possible.
d . Cr+KNO3
Cr is less reactive than K, so it cannot displace K from its compound.
Hence, This reaction is not possible.
Answer:
option c) Ba+Na 2 CO 3 -> BaCO3 +2Na
Answer:
C. Ba+Na 2 CO 3 -> BaCO3 +2NaPlease help please help
Answer:
sry I don't know much about chemistry
NO2 + H2O =
SO2 + H2O =
H2S + H2O=
SO2+ H2O=H2SO3
H2S+ H2O=H2SO4 +H2
NO2+ H2O= HNO3+NO
Please help me with this in the picture I need 8 thing wrong and 8 what should they do right
State the name(s) of the sub-atomic particle(s) that have/has a positive charge. Answer with the name of the particle(s) only.
A. Neurons
B. Protons
C. Electrons
Answer:
protons because they have the most positive charge
Hi Everyone ✌
hope u all r doin well
Pls Answer
What happens when dilute sulphuric acid is poured on a copper plate ?
Answer:
No observable change.
Explanation:
Copper renders dilute sulphuric acid passive, no reaction.
H2SO4+Cu-->CuSO4+H2
Explanation:
THIS IS THE CORRECT ANSWER
rare earth elements plz
Answer:
Rare earth elements are lanthanum, cerium, praseodymium, neodymium, promethium, samarium, europium, gadolinium, terbium, dysprosium, holmium, erbium, thulium, ytterbium, lutetium, scandium, yttrium - that appear in low concentrations in the ground.
Explanation:
The rare earth elements (REE) are a set of seventeen metallic elements. These include the fifteen lanthanides on the periodic table plus scandium and yttrium. Rare earth elements are an essential part of many high-tech devices.
SOMEONE HELP ASAP I NEED TO FIND AN ANSWER
Answer:
A) Q + XZ = X + QZ is a single displacement reaction.
B) Q + Z = QZ is a synthesis reaction
C) QT = Q + T is a decomposition reaction
D) QT + XZ = QZ + XT is double replacement reaction.
Explanation:
A) Q + XZ = X + QZ
This is a single displacement reaction because it is one in which one element is substituted for another one in a compound. In this case X is substituted for Q.
B) Q + Z = QZ
This is a synthesis reaction because Q and z combine to form a single product QZ.
C) QT = Q + T
This is a decomposition reaction because the compound QT breaks down to form 2 simpler substances Q and T.
D) QT + XZ = QZ + XT
Thus is a double replacement reaction because QT and XZ have exchanged cations to form new compounds QZ and XT
Figure 1 (Use this figure to answer questions 6,7, and 8. Assume that the height at point
A and point C are the same)
С
B
As the car moves from point A, to point B, and finally to point C, the total energy of the car
decreases from point A to point B, then increases from point B to point
increases from point A to point B, then decreases from point B to point
O is lost between points B and C
stays the same, but is converted between potential and kinetic energy
Answer:
JWBVH
Explanation:
NWSBWHSBHS
How do the Carnivorous plants survive without soil?
Answer:
A simple answer: Carnivores don't eat plants only flesh. So they would not need soil. But it would be hard for Carnivores to get energy because they get energy indirectly from the animals (herbivores) that they eat. How do they get the energy from a herbivore you might ask. Herbivores eat only plants and that gives the herbivore the plant's energy; but if the herbivore gets eaten, it is indirectly transferred into the Carnivore. Hope this helped!!
Carnivore = only feeds on flesh
Herbivore = eats only plants
Omnivore = eats plants and animals/flesh
What is pH?
O A. A measurement indicating how acidic a solution is
B. A concentration of total ions dissolved in solution
C. A level of dissolved gases that are in solution
O D. A component of solutions that makes them acidic
Answer:
Awnser is A
Explanation:
Answer:
Hello There!!
Explanation:
The answer is↬O A. A measurement indicating how acidic a solution is.
hope this helps,have a great day!!
~Pinky~
Select the correct answer.
A sample taken from a layer of mica in a canyon has 2.10 grams of potassium-40. A test reveals it to be 2.6 billion years old. How much
potassium-40 was in the sample originally if the half-life of potassium-40 is 1.3 billion years?
O A.
4.20 g
O B.
8.40 g
O C.
12.6 g
• D.
16.8 g
O E.
25.2 g
Answer:
8.36 g
Explanation:
From;
0.693/t1/2 = 2.303/t log (No/N)
t1/2 = half life of potassium-40
t = age of the sample
No= initial amount of the sample
N= amount of the sample at time t
Substituting values;
0.693/1.3 × 10^9 = 2.303/2.6 × 10^9 log (No/2.10)
5.33 × 10^-10 = 8.86 × 10^-10 log (No/2.10)
5.33 × 10^-10/8.86 × 10^-10 = log (No/2.10)
0.6 = log (No/2.10)
Antilog (0.6) = (No/2.10)
No = 2.10 × Antilog (0.6)
No= 8.36 g
The absorption spectrum of sodium has a line at 589 nm. What is the energy of this line? (The speed of light in a vacuum is 3.00 x 10^8 m/s, and Planck's constant is 6.626 x 10^-34 Jos.)
A. 8.89 x 10^26 J
B. 5.09 x 10^14 J
C. 3.37 x 10^-19 J
D. 2.96 x 10^18 J
Answer:
C. 3.37 x 10^-19 J
Explanation:
In the chemical reaction between aqueous magnesium chloride and sodium metal, what chemical amount (mol) of magnesium metal can be precipitated (produced) with 12.6 mol of sodium metal?
Answer:
6.3moles
Explanation:
The balanced equation of the reaction described above between aqueous magnesium chloride and sodium metal is as follows:
MgCl2(aq) + 2Na(s) → 2NaCl(aq) + Mg(s)
From the above equation, 2 moles of sodium metal (Na) produces 1 mole of Magnesium metal (Mg)
Hence, 12.6 mol of Na will produce (12.6/2) mol of Mg.
12.6/2 = 6.3moles of Mg metal.
KHP, the acid used in this experiment,
stands for potassium hydrogen
phosphorous.
True
False
Answer:
false
Explanation:
standard form is Potassium hydrogen phthalate
