The star is moving away from you. This is indicated by the fact that the observed wavelength (502.8 nm) is longer than the laboratory wavelength (500.7 nm), which is consistent with the Doppler effect caused by the star moving away from the observer.
What is Doppler effect?
The Doppler effect, named after Austrian physicist Christian Doppler, is the change in frequency of a wave in relation to an observer who is moving relative to the wave source. It is commonly observed with sound waves, but can also occur with light waves and other types of waves. When the observer is moving towards the source of the wave, the frequency and wavelength appear to increase, resulting in a higher pitch. When the observer is moving away from the source of the wave, the frequency and wavelength appear to decrease, resulting in a lower pitch or longer wavelength.
What is wavelength?
Wavelength is the distance between two consecutive points in a wave that are in phase, or at the same point in their cycle. It is usually represented by the symbol lambda (λ) and is measured in units of distance, such as meters or nanometers.
To know more about doppler effect, visit:
https://brainly.com/question/15318474
#SPJ1
For which of the following properties does the Moon have the largest value compared to the other planetary satellites (not moons of dwarf planets) in the Solar System?
The moon is a natural satellite that orbits Earth. It is the fifth-largest satellite in the solar system and the largest among planetary satellites.
What are the properties of the moon?The following properties are the ones where the Moon has the largest value compared to other planetary satellites:
Size: The moon is the fifth-largest satellite in the solar system, with a diameter of 3474 km. No other planetary satellite is as large as the moon. The closest satellite in terms of size is Ganymede, which is the largest moon of Jupiter and the ninth-largest object in the solar system, with a diameter of 5268 km.
Mass: The moon has a mass of 7.342 × 1022 kg, which is about 1.2% of Earth's mass. No other planetary satellite has a mass comparable to the moon, although a few come close. Ganymede has a mass of 1.5 × 1023 kg, which is about twice the mass of the moon, but it is a moon of Jupiter, not a planet.
Synchronous rotation: The moon is the only planetary satellite that is in synchronous rotation with its planet. This means that it takes the same amount of time for the moon to complete one orbit around Earth as it does to complete one rotation around its axis. As a result, the same side of the moon always faces Earth. No other planetary satellite has this property.
To know more about planetary satellites:
https://brainly.com/question/9545310
#SPJ11
You stand 3.5 m in front of a large mirror, and your little sister stands 2.0 m directly in front of you. At what distance should you focus your camera if you want to take a picture of your sister in the mirror?
Answer:
D = 3.5 m to mirror
d = 1.50 m from mirror to sister
Total distance from camera to sister = d + D = 5.0 m
consider a single crystal of some hypothetical metal that has the fcc crystal structure and is oriented such that a tensile stress is applied along a direction. if slip occurs on a (111) plane and in a direction, compute the stress at which the crystal yields if its critical resolved shear stress is 3.42 mpa.
Consider a single crystal of some hypothetical metal that has the FCC crystal structure and is oriented such that a tensile stress is applied along a direction. If slip occurs on a (111) plane and in a direction, compute the stress at which the crystal yields if its critical resolved shear stress is 3.42 MPa.
The resolved shear stress (τR) can be calculated using the following formula:τR = σs cos φ cos λWhere,σs = tensile stress applied along a directionφ = angle between tensile stress direction and (111) planeλ = angle between the slip direction and [110] directionThe resolved shear stress (τR) should be compared to the critical resolved shear stress (τc) to determine if slip will occur. If τR > τc, slip will occur. If τR < τc, the crystal will remain undeformed.In this case, the slip direction is also along [110] and therefore φ = λ.
The critical resolved shear stress (τc) = 3.42 MPa. Hence, for slip to occur,τR > τc ⇒ σs cos φ cos λ > τc cos φ cos λ = 3.42 MPaSince φ = λ, we can simplify the above equation toσs > τc / cos φ⇒ σs > 3.42 MPa / cos φIf we assume φ = 45°, we can substitute in this value to get the value of σs at which slip occurs:σs > 4.83 MPa. Therefore, the stress at which the crystal yields is 3.42 MPa.
Learn more about shear stress at:
https://brainly.com/question/30530774
#SPJ11
a ball is dropped from rest from a tower and strikes the ground 122.5 m below. a) approximately how many seconds does it take the ball to strike the ground after being dropped? b) with what velocity does it strike the ground? neglect air resistance.
The approximate time taken by the ball to hit the ground after being dropped is: 5 seconds.
The velocity at which the ball hits the ground is approximately 49.05 m/s, and it moves in the downward direction (negative velocity).
A ball is dropped from rest from a tower and strikes the ground 122.5 m below.
We are asked to determine the time taken by the ball to hit the ground, and the velocity at which it hits the ground.
The formula to calculate the time taken by an object to fall from rest from a height h is given by: t = sqrt (2h/g)
Here, h = 122.5m; g = 9.81m/s² (acceleration due to gravity)
Using the given formula, t = sqrt (2h/g) = sqrt (2 × 122.5 / 9.81)≈ 5 seconds
We know that, `v = g.t`
Since the ball was dropped from rest, its initial velocity is 0.
So the final velocity `v` is equal to the velocity at which it hits the ground.
Since g is negative, the velocity `v` will be negative, which means it is moving in the downward direction.
Using `g = 9.81 m/s²`,`t = 5 seconds`, we have = g.t = 9.81 × 5 = 49.05 m/s
To know more about "air resistance" refer here:
https://brainly.com/question/4428352#
#SPJ11
one electron collides elastically with a second electron initially at rest. after the collision, the radii of their trajectories are 0.00 cm and 3.00 cm. the trajectories are perpendicular to a uniform magnetic field of magnitude 0.0350 t. determine the energy (in kev) of the incident electron.
The energy of the incident electron is 26.3 keV. The energy is calculated from the conservation of energy which states that the initial energy is equal to the final energy of the electrons. Total energy is sum of kinetic energy and potential energy of the electrons.
The initial energy of the incident electron can be determined using the following equation:
[tex]E_{initial}= \Delta K + E_{final} + U[/tex]
where ΔK is the change in kinetic energy, [tex]E_{final}[/tex] is the final energy, and U is the potential energy.
Here, the second electron is initially at rest, and after the collision, the trajectories of the two electrons are at 90° to a uniform magnetic field. The magnetic force is perpendicular to the direction of motion, and hence, there is no work done. The potential energy U is, therefore, zero.
Initially, only the incident electron has energy, and hence, its initial energy is equal to its kinetic energy.
[tex]E_{initial} = \Delta K + E_{final}[/tex]
But, [tex]E_{final} = \frac{1}{2}mv_f^2[/tex]
Therefore,
[tex]E_{initial} = \Delta K + \frac{1}{2}mv_f^2[/tex]
The change in kinetic energy ΔK can be calculated using the following equation:
[tex]\Delta K = K_f - K_i[/tex]
But, [tex]K_i = \frac{1}{2}mv_i^2[/tex] where, [tex]v_i[/tex] is the initial velocity of the incident electron.
Therefore,
[tex]\Delta K = K_f - K_i= \frac{1}{2}mv_f^2 - \frac{1}{2}mv_i^2[/tex]
Substituting the given values,
[tex]\Delta K = \frac{1}{2}(9.11 \times 10^{-31} kg)(4.24\times 10^5 m/s)^2 - \frac{1}{2}(9.11\times10^{-31} kg)(3\times10^8 m/s)^2\\= -4.22\times10^{-15} Joules[/tex]
The energy of the incident electron can be converted to keV by dividing it by the charge of an electron and then multiplying by 1000.eV .
Therefore,
[tex]E_{initial} = 4.22 \times 10^{-15} J / (1.602 \times 10^{-19} C/eV)\\ = 26.3 keV[/tex]
Thus, the energy of the incident electron is 26.3 keV.
For further detail on the kinetic energy, click on the following link:
https://brainly.com/question/18461965
#SPJ11
5
Read the following sentences:
In those early games, balls and bats were often homemade. Anyone who
used a glove or mask was called a sissy. How would you like to squat
behind home plate with no glove or catcher's mask and have the ball
whiz toward you?
From this textual evidence, which viewpoint seems closest to what the article's
author likely believes?
A The changes in rules regarding safety in baseball over the years have been
an improvement.
B The changes in rules regarding safety in baseball over the years have not
made the game safer.
C
The changes in rules regarding safety in baseball over the years have had
no effect.
D The changes in rules regarding safety in baseball over the years may
be eliminated.
A block of weight w = 25.0 N sits on a frictionless inclined plane, which makes an angle 8 = 29.0° with respect to the horizontal, as shown in the figure. (Figure 1) A force of magnitude F = 12.1 N, applied parallel to the incline, is just sufficient to pull the block up the plane at constant speed.
Part B: What is We, the work done on the block by the force of gravity was the block moves a distance L = 3.40 m up the incline?
Part C. What is Wf the work done on the block by the applied force F as the block moves a distance L = 3.40 mm up the incline? Express your answer in Joules
a) The net Work done is zero. b) The work done on the block by the applied force F as the block moves a distance L is -41.2 J. c) The work done on the block by the applied force F as the block moves a distance L is 41.2 J.
Given:
Weight of the block (w) = 25.0 N
Distance moved by the block (d) = 3.40 m
The angle of the inclined plane (θ) = 29.0°
a) we know that from the work-energy theorem,
W = change in kinetic energy
But since speed is constant which means no change in KE, hence the net Work done is zero.
b) W = -mgy
W = -25 × (3.10 × sin29°)
W = -41.2 J
Therefore, the work done on the block by the force of gravity is -41.2 J.
c) The work done on the block by the applied force F as the block moves a distance L = 3.10m up the incline is,
W = Fd
W = 12.1 × 3.1
W = 41.2 J
Therefore, the work done on the block by the applied force F as the block moves a distance L is 41.2 J.
To know more about the work done:
https://brainly.com/question/26622905
#SPJ12
if stars a and b are both main-sequence stars and star a has a greater fusion rate than star b, which of the following statements hold(s)? check all that apply. A. star a must be more luminous than star b. B. star a must be less luminous than star b. C. star a must be more massive than star b. D. star a must be less massive than star b.
If stars A and B are both main-sequence stars and star A has a greater fusion rate than star B, the following statements hold:
A. Star A must be more luminous than star B.
C. Star A must be more massive than star B.
This is due to the direct relationship between a main-sequence star's brightness and mass and the rate of fusion in that star. A higher fusion rate, therefore, suggests a higher brightness and mass.
StarA star is a large, bright ball of gas that is held together by its own gravity. They create the energy and light that enable life on Earth and serve as the foundation of galaxies.In space, gas and dust clouds collide under the force of their own gravity to generate stars.Nuclear fusion starts when the cloud's center reaches roughly 10 million degrees Celsius as it warms up and falls. This is how hydrogen atoms come together to create helium, unleashing a massive quantity of energy in the form of heat and light.The star can retain a steady size and form because the energy produced by fusion produces an outward pressure that balances the pull of gravity.learn more about luminous here
https://brainly.com/question/25030787
#SPJ1
the range of frequencies on the electromagnetic spectrum called by?
The range of frequencies on the electromagnetic spectrum is known as the electromagnetic spectrum.
The spectrum ranges from radio waves, microwaves, infrared waves, visible light, ultraviolet rays, x-rays, and gamma rays. Each type of wave has a specific frequency range, ranging from hertz (Hz) to exahertz (EHz). The lowest frequency waves, such as radio waves, range from 3 kHz to 300 GHz, while the highest frequency waves, such as gamma rays, range from 300 GHz to 3 EHz.
The electromagnetic spectrum is divided into several sections, including radio waves, microwaves, infrared radiation, visible light, ultraviolet radiation, x-rays, and gamma rays. Each type of wave has its own properties and uses in different applications. Radio waves are used for communication, microwaves are used in satellite communication and imaging, infrared radiation is used in medical imaging, visible light is used to see our environment, ultraviolet radiation is used in sun protection and sterilization, x-rays are used in medical imaging and treatment, and gamma rays are used in medical treatment and research.
for such more question on electromagnetic spectrum
https://brainly.com/question/13803241
#SPJ11
What does the average kinetic energy of gas depend on?
Answer: temperature
Explanation: The last postulate of the kinetic molecular theory states that the average kinetic energy of a gas particle depends only on the temperature of the gas. Thus, the average kinetic energy of the gas particles increases as the gas becomes warmer.
In the context of the motor control process related to the speed-accuracy trade-off, the _____ phase of movement includes the beginning of limb movement in the direction of a target.
In the context of the motor control process related to the speed-accuracy trade-off, the initiation phase of movement includes the beginning of limb movement in the direction of a target.
What is motor control?Motor control is the ability to regulate and coordinate motor skills to achieve a desired outcome. The central nervous system (CNS) is in charge of regulating these skills. The CNS is divided into two parts: the peripheral nervous system (PNS) and the central nervous system (CNS). Motor skills are regulated by both parts of the nervous system. The CNS, on the other hand, is more involved in higher-level motor control.
A motor control system can be divided into three stages: planning, initiation, and execution. When the central nervous system processes the desired movement, it activates the motor program in the initiation stage, which produces the motor command sent to the muscles. Movement is initiated by the initiation stage. Following that, the movement is executed to meet the task's requirements. The motor program adjusts movement by making corrections based on previous trials and feedback. Therefore, the initiation phase is critical in the context of the motor control process related to the speed-accuracy trade-off.
Learn more about Motor control here:
https://brainly.com/question/29769703
#SPJ11
Since moving charges create magnetic fields and magnetic fields exert forces on moving charges, devices that are used to measure field strengths often affect the system they are being used to measure. Consider the wire segment in the figure, which is used to measure the magnetic field by determining the foree exerted on the current flowing through it. Part (a) Estimate the field the loop creates by calculating the field strength, in teslas, at the center of a circular loop 20.0 cm in diameter carrying
Part (b) What is the smallest field strength this loop can be used to measure with a 4.5 -A current, if its field should alter the measured field by 0.0100% or less?
a) The magnetic field at the center of loop 20.0 cm in diameter carrying is equals to the 2.8274×10⁻⁵ T.
b) Smallest magnetic field that change measured value by 0.0100% is equals to the 2.8274×10⁻⁹ T.
We know that moving charges create magnetic fields and magnetic fields exert forces on moving charges, devices that are used to measure field strengths. Consider the wire segment present in above figure.
A) Diameter of wire segment, d = 20 cm or 0.2 m carrying current I = 4.5 A
Magnetic Field at the center of current loop of segment, B= μ₀I/d
= 4π×10⁻⁷×4.5/0.2
= 2.8274×10⁻⁵ T
Therefore magnetic Field at the center of current loop 2.8274×10⁻⁵ T.
B) Current in carrying wire, I = 4.5 A
The field should be less than the measured field by 0.0100%. So, smallest field that change measured value by 0.0100% = 0.0100% of 2.8274×10⁻⁵ T
= 2.8274×10⁻⁹ T
Therefore Smallest field that change measured value by 0.0100% = 2.8274×10⁻⁹ T
For more information about magnetic field, visit :
https://brainly.com/question/26257705
#SPJ4
Complete question:
The above figure completes the question.
Since moving charges create magnetic fields and magnetic fields exert forces on moving charges, devices that are used to measure field strengths often affect the system they are being used to measure. Consider the wire segment in the figure, which is used to measure the magnetic field by determining the foree exerted on the current flowing through it. Part (a) Estimate the field the loop creates by calculating the field strength, in teslas, at the center of a circular loop 20.0 cm in diameter carrying
Part (b) What is the smallest field strength this loop can be used to measure with a 4.5 -A current, if its field should alter the measured field by 0.0100% or less?
what is the interference if: distance between a and b is 10mu distance between b and c is 15mu observed double crossover rate is: 0.25% group of answer choices
We cannot determine the value of interference with the given information.
The interference can be determined using the following formula:
interference = (observed double crossover rate - expected double crossover rate) ÷ (1 - expected double crossover rate).
The expected double crossover rate can be calculated using the formula:
expected double crossover rate = (distance AB × distance BC) ÷ total distance (AB + BC + AC).
Given:
Distance between A and B is 10mu;
Distance between B and C is 15mu;
Observed double crossover rate is 0.25%.
Therefore,
Distance AB = 10mu;
Distance BC = 15mu;
Total distance = AB + BC + AC
Expected double crossover rate = (10 × 15) ÷ (10 + 15 + AC)
expected double crossover rate = 150 ÷ (AC + 25)
The observed double crossover rate is 0.25%.
Therefore, the observed double crossover rate = 0.25% = 0.0025.
Interference = (observed double crossover rate - expected double crossover rate) ÷ (1 - expected double crossover rate)=
[0.0025 - (150 / (AC + 25))] ÷ [1 - (150 / (AC + 25))]
what is the interference if: distance between a and b is 10mu distance between b and c is 15mu observed double crossover rate is: 0.25%
To learn more about interference:https://brainly.com/question/16098226
#SPJ11
question 6: circuit balance given 6 , what is the current of the ideal current source, , for which there is no current flowing through the 5 resistor?
The current of the ideal current source in the given circuit is zero.
This is because the current source is not providing any current and the 5 ohm resistor is not providing any resistance. Thus, no current can flow through the circuit.
In this circuit, there is a current source with 6 volts and a 5 ohm resistor. The current source does not provide any current since it is ideal, meaning it does not create any voltage drops. Therefore, no current can flow through the circuit.
This is because there is no voltage difference between the two nodes (points) between which the current is supposed to flow.
The 5 ohm resistor also does not provide any resistance, meaning the same current would flow through the resistor as well. Thus, the current of the ideal current source in the given circuit is zero.
To know more about voltage drops click on below link:
https://brainly.com/question/28164474#
#SPJ11
suppose the roller coaster had had an initial speed of 5 m/s uphill instead, and it coasted uphill, stopped, and then rolled back down to a final point 20 m below the start. we would find in that case that its final speed is the same as its initial. explain in terms of conservation of energy.
In this case, the roller coaster starts with kinetic energy because it has an initial speed of 5 m/s.
Since the roller coaster's total energy is conserved throughout the ride, its final speed when it reaches the bottom will be the same as its initial speed of 5 m/s.
As it goes uphill, the kinetic energy is gradually converted into potential energy, so its speed decreases until it reaches the top, where it has only potential energy. When it stops, all the kinetic energy has been converted to potential energy. As the roller coaster rolls back down, the potential energy is converted back to kinetic energy, and its speed increases until it reaches the bottom, where all the potential energy has been converted back to kinetic energy.
This is because the roller coaster's potential energy at the top is equal to the sum of its initial kinetic energy and the work done by gravity as it went uphill. The roller coaster then converts all of its potential energy back into kinetic energy as it rolls back down the hill.
For more similar questions on conservation of energy and physics:
brainly.com/question/381281
#SPJ11
Light with wavelength equal to 105 nm falls on & metal surface. What is the minimum de Broglie wavelength of the photoelectrons emitted from this metal? Assume that the metal has & work function equal to 5.00 eV and use: h = 6.626 10-34 J.8 = 4.14 * 10-15 eV . 8; c = 3.00 x 108 m/s; mel = 9.11 x 10-31 kg; 1 eV 1.60 x 10-19 J.
The minimum de Broglie wavelength of the photoelectrons emitted from the metal is 2.19 x 10⁻⁹ m.
The energy of the incident photon can be calculated using the equation:
E = hc/λ
where h is the Planck constant, c is the speed of light, and λ is the wavelength of the light.
E = (6.626 x 10⁻³⁴J.s)(3.00 x 10⁸ m/s) / (105 x 10⁻⁹m)
E = 1.89 x 10⁻¹⁸ J
The work function of the metal is given as 5.00 eV, which can be converted to joules:
5.00 eV x 1.60 x 10⁻¹⁹ J/eV
= 8.00 x 10⁻¹⁹ J
The minimum energy required to eject an electron from the metal is the work function, so the kinetic energy of the emitted photoelectron can be calculated as:
K.E. = E - Work function
K.E. = 1.89 x 10⁻¹⁸ J - 8.00 x 10⁻¹⁹ J
K.E. = 1.09 x 10⁻¹⁸ J
The de Broglie wavelength of the photoelectron can be calculated using the equation:
λ = h/p
where h is the Planck constant and p is the momentum of the particle.
The momentum of the photoelectron can be calculated as:
p = √(2mK.E.)
where m is the mass of the electron.
p = √(2 x 9.11 x 10⁻³¹ kg x 1.09 x 10⁻¹⁸ J)
p = 3.03 x 10⁻²⁵ kg.m/s
Now, we can calculate the de Broglie wavelength of the photoelectron:
λ = h/p
λ = 6.626 x 10⁻³⁴ J.s / 3.03 x 10⁻²⁵ kg.m/s
λ = 2.19 x 10⁻⁹ m
Therefore, the minimum de Broglie wavelength of the photoelectrons emitted from the metal is 2.19 x 10⁻⁹ m.
Learn more about de Broglie wavelength here:
https://brainly.com/question/30404168
#SPJ11
Five docks are being tested in a laboratory. Exactly at noon, as determined by the WWV
Exactly at noon, as determined by the WWV time signal, on successive days of a week the clocks according to their relative value as good timekeepers, best to worst.
Time signals are also used in many everyday applications, such as GPS navigation, where precise timing is essential for calculating positions accurately. A time signal refers to any signal that provides information about the passage of time. Time signals are often used in experiments to measure the duration of events or to synchronize the timing of multiple processes.
One common type of time signal is a periodic signal, which repeats itself at regular intervals. This can be used to measure the period or frequency of a phenomenon, such as the oscillation of a pendulum or the vibration of a guitar string. Another type of time signal is a pulse signal, which provides a brief burst of energy at a specific time. This can be used to trigger the start or stop of a process or to measure the time delay between different events.
To learn more about Time signal visit here:
brainly.com/question/28875779
#SPJ4
Need help on my homework! Thanks.
Answer: Noble Gases (Blue)
A 71. 0 kg
football player is gliding across very smooth ice at 2. 05 m/s. He throws a 0. 440 kg
football straight forward
Using conservation of momentum the player's speed afterward if the ball is thrown at 17.5 ms relative to the player is 3.02 m/s.
We can use the principle of conservation of momentum to solve this problem, which states that the total momentum of a closed system remains constant if no external forces act on it.
Initially, the momentum of the system is the sum of the momentum of the football player and the football, given by:
p_initial = m_player × v_player + m_football × v_football
where:
m_player = 71 kg is the mass of the football player
v_player = 2 m/s is the initial velocity of the football player
m_football = 0.430 kg is the mass of the football
v_football = 17.5 m/s is the velocity of the football relative to the football player
Plugging in the values, we get:
p_initial = (71 kg)(2 m/s) + (0.430 kg)(17.5 m/s) = 15.325 kg m/s
After the football is thrown, the football player will move in the opposite direction with a new velocity v_player'. The momentum of the system after the throw is:
p_final = m_player × v_player' + m_football × v_football'
where v_football' = 0 m/s since the football has left the system.
Since the total momentum of the system is conserved, we have:
p_initial = p_final
which gives us:
m_player × v_player + m_football × v_football = m_player × v_player'
Solving for v_player', we get:
v_player' = (m_player × v_player + m_football × v_football) / m_player
Plugging in the values, we get:
v_player' = (71 kg × 2 m/s + 0.430 kg × 17.5 m/s) / 71 kg = 3.02 m/s
Therefore, the football player's speed after throwing the football is 3.02 m/s.
Learn more about the momentum at
https://brainly.com/question/30677308
#SPJ4
The question is -
A 71 kg football player is gliding across very smooth ice at 2 ms. He throws a 0.430 kg football straight forward. What is the player's speed afterward if the ball is thrown at 17.5 ms relative to the player?
what do you think might be causing the fluids in the lava lamp to move?
The fluid movement in a lava lamp is caused by the heat generated from the lamp's light bulb, which causes the wax or oil to rise and fall.
A lava lamp contains two fluids of different densities that do not mix. The fluids heat up as a result of the lamp's light bulb, causing them to expand and become less dense. The wax or oil floats up when it becomes less dense than the fluid that surrounds it, creating a globe at the top of the lamp.
The fluid is then cooled by the environment and becomes more dense, causing the wax to sink back to the bottom. This constant motion cycle creates the flowing effect seen in a lava lamp.
The heat from the light bulb causes the fluid to expand, and as it does, it becomes less dense than the surrounding fluid, causing it to float. When the fluid cools, it becomes denser and settles back down to the bottom. This cyclic motion creates the soothing flow of a lava lamp.
For more such questions on lava lamp, click on:
https://brainly.com/question/30542979
#SPJ11
he radius of a sphere is increasing at a rate of 4 mm/s. how fast is the volume increasing when the diameter is 40 mm? incorrect: your answer is incorrect. mm3/s
The volume is increasing at a rate of approximately 20,106 mm³/s.
The volume of a sphere can be given by the formula V = 4/3πr³. To determine the rate of change of volume of the sphere, we need to differentiate the formula with respect to time.
The derivative of V w.r.t. t is given by dV/dt = 4πr²(dr/dt)
Where dV/dt is the rate of change of volume of the sphere and dr/dt is the rate of change of radius.
It is given that the radius is increasing at a rate of 4 mm/s; therefore, we have dr/dt = 4 mm/s
Radius r = (diameter)/2
When the diameter is 40mm, radius r = 20 mm. Substituting the values into the formula, we get;
dV/dt = 4π(20)²(4) = 6400π mm³/s
Therefore, the rate of change of volume of the sphere is 6400π mm³/s or approximately 20,106 mm³/s.
Learn more about rate of change here: https://brainly.com/question/28520282.
#SPJ11
consider a 10 m length of 2 cm-i.d tube. what is the average convective heat transfer coefficient and pressure gradient inside the tube when the tube wall is at 330 k and water enters at 300 k, 1 atm pressure, and flows at a velocity of 3 m/s?
The average convective heat transfer coefficient and pressure gradient inside a 10 m long tube with a 2 cm inner diameter when the tube wall is at 330 K and water enters at 300 K and 1 atm pressure, flowing at a velocity of 3 m/s, is: 1420 W/m²K and 2.6 x 10⁴ Pa
This can be calculated using the equations of fluid mechanics. The average convective heat transfer coefficient, or h, is determined using the following equation:
[tex]h = (k/d) x (v/P).[/tex]
k is the thermal conductivity of the fluid (water), d is the tube inner diameter, v is the velocity of the fluid, and P is the pressure gradient across the tube wall.
The pressure gradient is found using the equation: [tex]P = (v²/2g) + P₀[/tex],
where v is the fluid velocity, g is the acceleration due to gravity, and P₀ is the pressure at the inlet of the tube (1 atm in this case). Plugging the given values into the equations yields a heat transfer coefficient of 1420 W/m²K and a pressure gradient of 2.6 x 10⁴ Pa.
In conclusion, the average convective heat transfer coefficient and pressure gradient inside a 10 m long tube with a 2 cm inner diameter when the tube wall is at 330 K and water enters at 300 K and 1 atm pressure, flowing at a velocity of 3 m/s, is 1420 W/m²K and 2.6 x 10⁴ Pa, respectively.
To know more about heat transfer refer here:
https://brainly.com/question/30416117#
#SPJ11
a fixed amount of a molecular substance in the liquid phase is placed in a flask at constant temperature. the flask is closed and is allowed to come to equilibrium. select all the statements that correctly describe the processes occurring in the flask. multiple select question. a. the relative amounts of liquid and vapor in the flask remain constant. b. molecules are leaving and entering the liquid phase at the same rate. c. no changes are occurring because the system is at equilibrium. d. the amount of liquid remains the same because evaporation is no longer occurring.
The statements that correctly describe the processes occurring in the flask are A and B. C and D are incorrect statetment.
a) States that the relative amounts of liquid and vapor in the flask remain constant, which is true as equilibrium has been reached, meaning that the rate of evaporation equals the rate of condensation. b) states that molecules are leaving and entering the liquid phase at the same rate, which is also true as equilibrium has been reached.
c) and d) are incorrect because they do not accurately describe the processes occurring in the flask; while the system is at equilibrium, it is still in a state of change with molecules leaving and entering the liquid phase at the same rate.
Learn more about term of equilibrium: brainly.com/question/517289
#SPJ11
An electric lamp consumes 60 watts at 220 volts. How many dry cells of EMF 1. 5 volt and internal resistance 1 ohm are required to glow the lamp?
We must figure out the total voltage and current required to generate 60 watts of electricity in order to calculate the number of dry cells necessary to light the bulb.
Voltage (V) x Current Equals Power (P) (I)
We are provided 220 volts of voltage and 60 watts of power (P). Hence, the current (I) may be determined as follows:
I equals P / V at 60 W and 220 V, or 0.273 A.
We must sum the EMFs of the cells in series in order to determine the overall voltage needed to power the light using dry cells:
n times EMF = V total
the number of cells is n.
Since the EMF of each cell is 1.5 volts, the total voltage needed may be written as follows:
1.5 n V total
learn more about electricity here:
https://brainly.com/question/8971780
#SPJ4
a missile of mass 1.20 102 kg is fired from a plane of mass 4.80 103 kg initially moving at a speed of 3.25 102 m/s. if the speed of the missile relative to the plane is 1.06 103 m/s, what is the final velocity of the plane?
The final velocity of the plane after a missile of mass 1.20 102 kg is fired from the plane is 0.255 m/s.
To find the final velocity of the plane when a missile of mass 1.20 x 10² kg is fired from a plane of mass 4.80 x 10³ kg initially moving at a speed of 3.25 x 10² m/s, and the speed of the missile relative to the plane is 1.06 x 10³ m/s, we can use the conservation of momentum.The initial momentum of the system is given by:
m1v1 + m2v2 = (m1 + m2)vf
where m1 = mass of missile, m2 = mass of the plane, v1 = velocity of the missile, v2 = velocity of the plane, and vf = final velocity of the system
Substituting the given values, we get:(1.20 x 10² kg) (1.06 x 10³ m/s) + (4.80 x 10³ kg) (3.25 x 10² m/s) = (1.20 x 10² kg + 4.80 x 10³ kg) vf
Simplifying, we get:1284 = (5.04 x 10³ kg) vf
Therefore, vf = 1284 / (5.04 x 10³ kg) = 0.255 m/s. So, the final velocity of the plane is 0.255 m/s.
More on velocity: https://brainly.com/question/20038545
#SPJ11
if a force is exerted on an object, is it possible for that object to be moving with constant velocity? explain
Yes, it is possible for an object to be moving with a constant velocity even when force is exerted on the object. When an object is in a state of rest, a force is required to move it from that position.
What is Newton's second law of motion?Newton’s second law states that the acceleration of an object is directly proportional to the force exerted on it and inversely proportional to its mass. Thus, a larger force results in a greater acceleration of the object. If there is no force applied to the object, the object will remain stationary or move at a constant velocity.
However, if there is a force applied to the object, it will accelerate. If the force applied is balanced by an equal and opposite force, the object will continue to move with a constant velocity. An object in motion is said to be in equilibrium when the net force acting on the object is zero. When the net force acting on an object is zero, it moves at a constant velocity. Therefore, if a force is exerted on an object, it is possible for the object to be moving with a constant velocity if the forces are balanced.
Learn more about Newton's law here:
https://brainly.com/question/13447525
#SPJ11
Based on the equation given in the lab manual, what is the equation to find the equivalent resistance of two resistors in parallel? Note: I do not want inverse resistance, I'm asking for R = ..) R1 + R2 Req + R2 Req R2 R1 Rea R1 R2 R1+R2
This equation can be used to determine the equivalent resistance of two parallel resistors: 1/Req = 1/R1 + 1/R2 Upon solving for Req, we obtain: Requirement = (R1-R2) / (R1+R2)
What is the parallel pairing of two resistors' equivalent resistance?The equivalent resistance of two identical resistors connected in parallel is equal to one-half the value of each resistor. Both share an equal amount of the current.
How are resistance and resistance calculated?Resistors are connected in series when they are connected one after the other. This is seen below. You add up the individual resistances to determine the total overall resistance of several resistors connected in this manner. The following equation is used to accomplish this: Rtotal = R1 + R2 + R3 and so forth.
To know more about resistance visit:-
https://brainly.com/question/13110234
#SPJ1
You are standing on the surface of a spherical asteroid 10 km in diameter, of density 3000 kg/m3.
Part A
Calculate the escape velocity from the asteroid in km/s.
Express your answer in kilometers per second using two significant figures.
Calculate the escape velocity from the asteroid in mph.
Express your answer in miles per hour using three significant figures
The correct answer for the (A) Escape velocity is [tex]570[/tex] (B) Escape velocity is [tex]0.57[/tex] in Km/h and (c). Escape velocity is [tex]1.27[/tex] in mph.
Given:
Diameter of asteroid D = [tex]10[/tex] km
Radius R = [tex]5[/tex] Km
Density [tex]\rho[/tex] = [tex]3000[/tex] kg/m³
Unit conversion;
[tex]1[/tex] m/s = [tex]0.001[/tex] Km/s
[tex]1[/tex] m/s = [tex]2.23694[/tex] mph
(A)To calculate Escape velocity:
Use the formula;
[tex]v_e = \sqrt{\dfrac{2GM}{R} }[/tex]
Gravitational Constant [tex]G[/tex] = [tex]6.67430[/tex]
To calculate Mass([tex]M[/tex]) of the asteroid, Calculate Volume([tex]V[/tex]) of the sphere and multiply it with density([tex]\rho[/tex]).
[tex]V= \dfrac{4}{3} \pi R^3 \\\\\rho = \dfrac{M}{V}[/tex]
[tex]M = \rho*V[/tex]
= [tex]523598775000[/tex] Kg
Escape velocity:
[tex]v_e = \sqrt{\dfrac{2*6.67430 * 10^{-11} * 523598775000}{5000} }[/tex]
[tex]= 570[/tex] m/s
(B)Escape velocity in Km/s:
[tex]v_e = \dfrac{570}{1000}[/tex]
[tex]= 0.57[/tex] Km/s
(B)Escape velocity in mph:
[tex]v_e = 0.57 * 2.23694[/tex]
[tex]= 1.27[/tex] mph
Escape velocity is [tex]570[/tex] m/s. In Km/h is [tex]0.57[/tex] and In mph is [tex]1.27[/tex] .
Learn more about Escape velocity here:
https://brainly.com/question/31201121
#SPJ12
One object is placed on each shelf in the image above (W, X, Y, Z). The four objects have the same mass, 2.0 kg. Match each object to its potential energy.
Object W 7.84 J 15.7 J 13.4 J 0 J 23.5 J 5.62
Object X
Object Y
Object Z
Potential Energy of Object W, X, Y and Z are 0 J, 7.84 J, 15.7J and 23.5J, for better understand we have to know the meaning of potential energy.
What is Potential Energy?Potential energy in physics is the energy that an item retains as a result of its location in relation to other objects, internal tensions, electric charge, or other elements. Potential energy develops in systems having components whose configurations, or relative positions, determine the amount of the forces they apply to one another.
Potential Energy of an Object = m * g * h
Where, m = mass,
g = gravity, and
h = height
Potential Energy of Object W = 2 * 9.8 * 0
= 0 J
Potential Energy of Object X = 2 * 9.8 * 0.4
= 7.84 J
Potential Energy of Object Y = 2 * 9.8 * 0.8
= 15.68 J
≈ 15.7 J
Potential Energy of Object Z = 2 * 9.8 * 1.2
= 23.5 J
Therefore, Potential Energy of Object W, X, Y and Z are 0 J, 7.84 J, 15.7 J and 23.5 J.
To Learn more about Potential Energy, visit:
https://brainly.com/question/1242059
#SPJ1
A car’s cooling system contains 25 kg of water. What is the increased change in temperature of the water if 872. 0 kJ of thermal energy is added?
When 872.0 kJ of thermal energy are injected, the temperature of the 25 kg of water in the car's cooling system changes by 35.0 degrees Celsius.
Water's specific heat capacity (J/(gK), or 4,180 J/ (kgK). Thus, we can use the following formula to get the temperature change:
Q = mcΔT
where Q is the extra thermal energy (872 000 J), m the water mass (25 kg), c the water's specific heat capacity (4,180 J/(kg*K)), and T the temperature change.
When we solve for T, we get:
The equation T = Q/(mc) Equals 872,000 J/(25 kg * 4,180 J/(kgK)) = 35.0 °C.
When 872.0 kJ of thermal energy are injected, the temperature of the 25 kg of water in the car's cooling system changes by 35.0 degrees Celsius.
learn more about energy here:
https://brainly.com/question/1932868
#SPJ4
