Answer:
CHC12
Explanation:
i am not really sure i am onna do a quick research 4 u tho
A mixture of 50ml of 0.1M HCOOH and 50ml of 0.05M NaOH is equivalent to
Answer:
d) a solution that is 0.025M in HCOOH and 0.025M in HCOONa
Explanation:
The reaction of a weak acid (HOOH) with NaOH is as follows:
HCOOH + NaOH → HCOONa + H₂O
Based on the reaction, 1 mole of the acid reacts with 1 mole of the base (Ratio 1:1).
The initial moles of both species are:
HCOOH: 0.050L × (0.1mol / L) = 0.0050 moles of HCOOH
NaOH: 0.050L × (0.05 mol / L) = 0.0025 moles NaOH
After the reaction, all NaOH reacts with HCOOH producing HCOONa (Because moles of NaOH < moles HCOOH).
Final moles:
HCOOH: 0.0050 moles - 0.0025 moles (After reaction) = 0.0025 moles
HCOONa: Moles HCOONa = Initial Moles NaOH: 0.0025 moles
As volume of the mixture is 100mL (50 from the acid + 50 from NaOH), molarity of both HCOOH and HCOONa is:
0.0025 moles / 0.100L = 0.025M of both HCOOH and HCOONa
Thus, the initial mixture is equivalent to:
d) a solution that is 0.025M in HCOOH and 0.025M in HCOONaBecause of movements at the Mid-Atlantic Ridge, the Atlantic Ocean widens by about 2.5 centimeters each year. Explain which type of plate boundary causes this motion.
Answer:
A divergent plate boundary
Explanation:
At a divergent boundary, the plates pull away from each other and generate new crust.
Answer:
Because the ocean becomes larger, this is a divergent plate boundary. Divergent plates cause the ocean floor to expand, making the ocean larger.
Explanation:
PLATO ANSWER
Select the true statement concerning voltaic and electrolytic cells. Select one: a. Voltaic cells involve oxidation-reduction reactions while electrolytic cells involve decomposition reactions. b. Voltaic cells require applied electrical current while electrolytic cells do not. . c. all electrochemical cells, voltaic and electrolytic, must have spontaneous reactions. d. Electrical current drives nonspontaneous reactions in electrolytic cells.
Answer:
Electrical current drives nonspontaneous reactions in electrolytic cells.
Explanation:
Electrochemical cells are cells that produce electrical energy from chemical energy.
There are two types of electrochemical cells; voltaic cells and electrolytic cells.
A voltaic cell is an electrochemical cell in which electrical energy is produced from spontaneous chemical process while an electrolytic cell is an electrochemical cell where electrical energy is produced from nonspontaneous chemical processes. Current is needed to drive these nonspontaneous chemical processes in an electrolytic cell.
Answer:
electrolytic cells generate electricity through a non-spontaneous reaction while voltaic cells absorb electricity to drive a spontaneous reaction.
Explanation:
Answer via Educere/ Founder's Education
3,3-dibromo-4-methylhex-1-yne
Explanation:
see the attachment. hope it will help you...If the theoretical yield of a reaction is 332.5 g and the percent yield for the reaction is 38 percent, what's the actual yield of product in grams? \
A. 8.74 g
B. 12616 g
C. 116.3 g
D. 126.4 g
Answer: D - 126.4g
Explanation:
% Yield = Actual Yield/Theoretical Yield
38% = Actual Yield/332.5
38/100 = Actual Yield/332.5
(.38)(332.5) = 126.35 g = 126.4 g Actual Yield
Answer:
is D. the correct answer
Explanation:
I'm not sure if it is. Please let me know if I'm mistaking.
Find the pH of these buffer solutions using the information provided: 1L solution containing 80g of lactic acid (MW
Answer:
pH of the solution is 2.0
Explanation:
The lactic acid is a weak acid that is in equilibrium with water as follows:
Lactic acid + H2O ⇄ Lactate + H₃O⁺
And Ka for lactic acid: 1.38x10⁻⁴
Ka = 1.38x10⁻⁴ = [Lactate] [H₃O⁺] / [Lactic acid]
Initial concentration of lactic acid is (MW: 112.06g/mol):
80g * (1mol / 112.06g) / 1L = 0.714M
The equilibrium concentration of the species in the equilibrium are:
[Lactate] = X
[H₃O⁺] = X
[Lactic acid] = 0.714-X
Replacing in Ka expression:
1.38x10⁻⁴ = [X] [X] / [0.714-X]
9.8532x10⁻⁵ - 1.38x10⁻⁴X = X²
9.8532x10⁻⁵ - 1.38x10⁻⁴X - X² = 0
Solving for X:
X = -1.0x10⁻². False solution, there is no negative concentrations
X = 9.86x10⁻³M. Right solution.
As [H₃O⁺] = X
[H₃O⁺] = 9.86x10⁻³M
and pH = -log [H₃O⁺] = -log 9.86x10⁻³M
pH = 2.0
pH of the solution is 2.0g Which ONE of the following pairs of organic compounds are NOT pairs of isomers? A) butanol ( CH3-CH2-CH2-CH2-OH ) and diethyl ether ( CH3–CH2–O–CH2–CH3 ) B) isopentane ( (CH3)2-CH-CH2-CH3 ) and neopentane ( (CH3)4C ) C) ethanolamine ( H2N-CH2-CH2-OH ) and acetamide ( CH3-CO-NH2 ) D) acrylic acid ( CH2=CH-COOH ) and propanedial ( OHC–CH2–CHO ) E) trimethylamine ( (CH3)3N ) and propylamine ( CH3-CH2-CH2-NH2 )
Answer:
ethanolamine ( H2N-CH2-CH2-OH ) and acetamide ( CH3-CO-NH2 )
Explanation:
Isomers are compounds that have the same molecular formula but different structural formulas. Hence any pair of compounds that can be represented by exactly the same molecular formula are isomers of each other.
If we look at the pair of compounds; ethanolamine ( H2N-CH2-CH2-OH ) and acetamide ( CH3-CO-NH2 ), one compound has molecular formula, C2H7ON while the other has a molecular formula, C2H5ON, hence they are not isomers of each other.
What creation would you make if you had access to any of the chemical elements? can someone answer this for me please.
Answer:
Depends on the chemicals.
Explanation:
The creation of something depends on the chemical we have. If I have chemicals such as acid and base so I can produce salt and water by mixing acid and base. If I have ethanol, vegetable oil and sodium hydroxide which is a catalyst, I can produce biodiesel which can be used in vehicles instead of fossil fuel. If I have sodium element and chlorine gas, I can produce sodium chloride also known as table salt.
A chemist prepares a solution of sodium chloride by measuring out 25.4 grams of sodium chloride into a 100. mL volumetric flask and filling the flask to the mark with water. Calculate the concentration in mol/L of the chemist's sodium chloride solution. Be sure your answer has the correct number of significant digits.
Answer:
The concentration in mol/L = 4.342 mol/L
Explanation:
Given that :
mass of sodium chloride = 25.4 grams
Volume of the volumetric flask = 100 mL
We all know that the molar mass of sodium chloride NaCl = 58.5 g/mol
and number of moles = mass/molar mass
The number of moles of sodium chloride = 25.4 g/58.5 g/mol
The number of moles of sodium chloride = 0.434188 mol
The concentration in mol/L = number of mol/ volume of the solution
The concentration in mol/L = 0.434188 mol/ 100 × 10⁻³ L
The concentration in mol/L = 4.34188 mol/L
The concentration in mol/L = 4.342 mol/L
Calculate the molarity of a solution containing 29g of glucose (C 6 H 12 O 6 ) dissolved in 24.0g of water. Assume the density of water is 1.00g/mL.
Answer:
whats the ph ofpoh=9.78
Explanation:
Which of the following contains a nonpolar covalent bond?
O A. Co
B. NaCl
O C. 02
O D. HE
Answer:
The answer is o2
Explanation:
I took the test
(a) Identify the name of the method used below for the separation.
(b) Give one more application of this method of separation.
(c) What is the name for the line at position B ?
(d) what conclusions can you draw about the colours present in sweets C and D ?
Answer:
(a) Chromatography
(b) DNA fingerprinting
(c) Origin
(d) Sweet C consists of more colours than sweet D.
ii. The speed of colours in sweet C are proportional to one another, while that of colours in D is not.
Explanation:
Chromatography is one of the physical method of separating mixtures. This process composed of the ability of the constituents in a mixture to separate by virtue of rate of movement through a medium, thus separates into constituents.
It can be used to determine the soluble constituents of a given mixture. And for purification purpose.
Consider these metal ion/metal standard reduction potentials Cd2+(aq)|Cd(s) Zn2+(aq)|Zn(s) Ni2+(aq)|Ni(s) Cu2+(aq)|Cu(s) Ag+(aq)|Ag(s) -0.40 V -0.76 V ‑0.25 V +0.34 V +0.80 V Based on the data above, which species is the best reducing agent?
Answer:
The best reducing agent is Zn(s)
Explanation:
A reducing agent must to be able to reduce another compound, by oxidizing itself. Consequently, the oxidation potential must be high. The oxidation potential of a compound is the reduction potential of the same compound with the opposite charge. Given the reduction potentials, the best reducing agent will be the compound with the most negative reduction potential. Among the following reduction potentials:
Cd₂⁺(aq)|Cd(s) ⇒ -0.40 V
Zn²⁺(aq)|Zn(s) ⇒ -0.76 V
Ni²⁺(aq)|Ni(s) ⇒‑0.25 V
Cu²⁺(aq)|Cu(s) ⇒ +0.34 V
Ag⁺(aq)|Ag(s) ⇒ +0.80 V
The most negative is Zn²⁺(aq)|Zn(s) ⇒ -0.76 V
From this, the most reducing agent is Zn. Zn(s) is oxidized to Zn²⁺ ions with the highest oxidation potential (0.76 V).
One way the U.S. Environmental Protection Agency (EPA) tests for chloride contaminants in water is by titrating a sample of silver nitrate solution. Any chloride anions in solution will combine with the silver cations to produce bright white silver chloride precipitate. Suppose an EPA chemist tests a sample of groundwater known to be contaminated with nickel(II) chloride, which would react with silver nitrate solution like this:
Answer:
6.5 mg/L.
Explanation:
Step one: write out and Balance the chemical reaction in the Question above:
NiCl2 + 2AgNO3 =====> 2AgCl + Ni(NO3)2.
Step two: Calculate or determine the number of moles of AgCl.
So, we are given that the mass of AgCl = 3.6 mg = 3.6 × 10^-3 g. Therefore, the number of moles of AgCl can be calculated as below:
Number of moles AgCl = mass/molar mass = 3.6 × 10^-3 g / 143.32. = 2.5118 × 10^-5 moles.
Step three: Calculate or determine the number of moles of NiCl2.
Thus, the number of moles of NiCl2 = 2.5118 × 10^-5/ 2 = 1.2559 × 10^-5 moles.
Step four: detemine the mass of NiCl2.
Therefore, the mass of NiCl2 = number of moles × molar mass = 1.2559 × 10^-5 moles × 129.6 = 1.6 × 10^-3 g.
Step five: finally, determine the concentration of NiCl2.
1000/ 250 × 1.6 × 10^-3 g. = 6.5 mg/L.
The half-life of radium-226 is 1620 years. What percentage of a given amount of the radium will remain after 900 years
Answer:
68%
Explanation:
Since we need a percentage we can use any number we want for our initial value.
5(1/2)^900/1620 = 3.40
(3.40 / 5)*100 = 68%
To make sure lets use a different initial amount
1(1/2)^900/1620 = 0.68
(0.68/1) * 100 = 68%
To solve this question, we'll assume the initial amount of radium-226 to be 1.
Now, we shall proceed to obtaining the percentage of radium-226 that will after 900 years. This can be obtained as illustrated below:
Step 1Determination of the number of half-lives that has elapsed.
Half-life (t½) = 1620 years
Time (t) = 900 years
Number of half-lives (n) =?[tex]n = \frac{t}{t_{1/2}}\\\\n = \frac{900}{1620}\\\\n = \frac{5}{9}[/tex]
Step 2:Determination of the amount remaining
Initial amount (N₀) = 1
Number of half-lives (n) = 5/9
Amount remaining (N) =?[tex]N = \frac{N_{0} }{2^{n}}\\\\N = \frac{1}{2^{5/9}}[/tex]
N = 0.68Step 3Determination of the percentage remaining.
Initial amount (N₀) = 1
Amount remaining (N) = 0.68
Percentage remaining =?Percentage remaining = N/N₀ × 100
Percentage remaining = 0.68/1 × 100
Percentage remaining = 68%Therefore, the percentage amount of radium-226 that remains after 900 years is 68%
Learn more: https://brainly.com/question/10406952
Which of the following provides a characteristic of
MgO(s) with a correct explanation?
Choose 1 answer:
А
It is hard because its ions are held together by strong
electrostatic attractions.
B
It is malleable because its atoms can easily move past
one another without disrupting the bonding.
It is a poor conductor of electricity because its
electrons are tightly held within covalent bonds and
lone pairs.
It has a high melting point because its molecules
interact through strong intermolecular forces.
Answer:
А It is hard because its ions are held together by strong electrostatic attractions.
B It is malleable because its atoms can easily move past one another without disrupting the bonding.
Explanation:
These are correct explanations of the properties of magnesium.
C is wrong. Mg is a good conductor of electricity and it has metallic bonds.
D is wrong. Mg has no molecules. It has no intermolecular forces.
Solid cesium bromide has the same kind of crystal structure as CsCl which is pictured below: If the edge length of the unit cell is 428.7 pm, what is the density of CsBr in g/cm3.
Answer:
[tex]\mathbf {density \ d =4.4845 \ g/cm^3}[/tex]
Explanation:
Let recall the crystal structure of CsBr obtains a BCC structure. In a BCC structure, there exist only two atom per cell.
The density d of CsBr in g/cm³ can be calculated by using the formula:
[tex]\mathtt{ density \ d = \dfrac{z \times molar\ mass \ (M)}{ edge \ length \ (a) \ \times avogadro's \ number \ (N)}}[/tex]
where;
z = 1 mole of CsBr
edge length = 428.7 pm = (4.287 × 10⁻⁸)³ cm
molar mass of CsBr = 212.81 g/mol
avogadro's number = 6.023 × 10²³
[tex]\mathtt{ density \ d = \dfrac{1 \times 212.81}{(4.287 \times 10^{-8})^3 \times 6.023 \times 10^{23}}}[/tex]
[tex]\mathtt{ density \ d = \dfrac{ 212.81}{47.4540533}}[/tex]
[tex]\mathbf {density \ d =4.4845 \ g/cm^3}[/tex]
A piece of plastic sinks in oil but floats in water. Place these three substances in order from lowest density to greatest density.
Answer:
[tex]\rho _{oil}<\rho _{plastic}<\rho _{water}[/tex]
Explanation:
Hello,
In this case, since water and oil are immiscible due to the oil's nonpolarity and water's polarity, when mixed, the oil remains on the water since it is less dense than water. In such a way, for a plastic sunk in the oil and floating on the water (in middle of them) we can conclude that the plastic have a mid density, therefore, the required organization is:
[tex]\rho _{oil}<\rho _{plastic}<\rho _{water}[/tex]
Best regards.
15. Calculate the critical angle of glass and water combination. Show your calculation. 16. What is the critical angle for the interface between Mystery A and glass
Answer:
15. Critical angle of glass and water combination, θ = 62.45°
16. Critical angle for the interface between Mystery A and glass, θ = 37.93°
Note; The question is incomplete. The complete question is as follows:
Medium Air Water Glass Mystery A Mystery B Table-2 Speed (m/s) 1.00 C 0.75 c 0.67 0.41 c 0.71 c n 1.00 1.33 1.50 Index of Refraction n of a given medium is defined as the ratio of speed of light in vacuum, c to the speed of light in a medium, v. n = c/v
Table-4: Incident Angle (degrees) Reflected Angle Refracted angle (degrees) (degrees) % Intensity of reflected ray 0 10 20 30 40 50 N/A N/A N/A 30 40 50 0 11.3 22.7 34.2 46.3 59.5 N/A N/A N/A 0.67 1.22 3.08 % Intensity of refracted ray 100 100 100 99.33 98.78 96.92
When rays travel from a denser medium to a less dense medium, we can define a critical angle of incidence θ such that refracted angle θ₂ = 90°. Applying Snell's law: Critical angle θ = sin-1(n₂/n₁).
When the angle of incidence is greater than the critical angle, 100% of the light intensity is reflected. This is called total internal reflection because all the light is reflected.
15. Calculate the critical angle of glass and water combination. Show your calculation.
16. What is the critical angle for the interface between Mystery A and glass?
Explanation:
15. Applying Snell's law; Critical angle θ = sin-1(n₂/n₁).
where n₂,refractive index of water = 1.33, n₁, refractive index of glass = 1.50 since glass is denser than water
θ = sin-1(1.33/1.50)
θ = 62.45°
Critical angle of glass and water combination, θ = 62.45°
16. Refractive index of mystery A , n = c/v
where v = 0.41 c
therefore, n = c / 0.41 c = 2.44
Critical angle for the interface between Mystery A and glass, θ = sin-1(n₂/n₁).
where n₂,refractive index of glass = 1.50, n₁, refractive index of mystery A = 2.44 since mystery A is denser than glass as seen from its refractive index
θ = sin-1(1.50/2.44)
θ = 37.93°
Critical angle for the interface between Mystery A and glass, θ = 37.93°
9
What might happen if acidic chemicals were emitted into
the air by factories? Choose the best answer.
A
The acid would destroy metallic elements in the air
B
The acid would be neutralized by bases within clouds
C
Acid rain might destroy ecosystems and farmland
D
Violent chemical reactions would take place within the
atmosphere
co search
O
BI
Calculate the amount of heat that must be absorbed by 10.0 g of ice at –20°C to convert it to liquid water at 60.0°C. Given: specific heat (ice) = 2.1 J/g·°C; specific heat (water) = 4.18 J/g·°C; ΔH fus = 6.0 kJ/mol.
Answer:
The amount of heat to absorb is 6,261 J
Explanation:
Calorimetry is in charge of measuring the amount of heat generated or lost in certain physical or chemical processes.
The total energy required is the sum of the energy to heat the ice from -20 ° C to ice of 0 ° C, melting the ice of 0 ° C in 0 ° C water and finally heating the water to 60 ° C.
So:
Heat required to raise the temperature of ice from -20 °C to 0 °CBeing the sensible heat of a body the amount of heat received or transferred by a body when it undergoes a temperature variation (Δt) without there being a change of physical state (solid, liquid or gaseous), the expression is used:
Q = c * m * ΔT
Where Q is the heat exchanged by a body of mass m, made up of a specific heat substance c and where ΔT is the temperature variation (ΔT=Tfinal - Tinitial).
In this case, m= 10 g, specific heat of the ice= 2.1 [tex]\frac{J}{g*C}[/tex] and ΔT=0 C - (-20 C)= 20 C
Replacing: Q= 10 g*2.1 [tex]\frac{J}{g*C}[/tex] *20 C and solving: Q=420 J
Heat required to convert 0 °C ice to 0 °C waterThe heat Q necessary to melt a substance depends on its mass m and on the called latent heat of fusion of each substance:
Q= m* ΔHfusion
In this case, being 1 mol of water= 18 grams: Q= 10 g*[tex]6.0 \frac{kJ}{mol} *\frac{1 mol of water}{18 g}[/tex]= 3.333 kJ= 3,333 J (being kJ=1,000 J)
Heat required to raise the temperature of water from 0 °C to 60 °CIn this case the expression used in the first step is used, but being: m= 10 g, specific heat of the water= 4.18 [tex]\frac{J}{g*C}[/tex] and ΔT=60 C - (0 C)= 60 C
Replacing: Q= 10 g*4.18 [tex]\frac{J}{g*C}[/tex] *60 C and solving: Q=2,508 J
Finally, Qtotal= 420 J + 3,333 J + 2,508 J
Qtotal= 6,261 J
The amount of heat to absorb is 6,261 J
The amount of heat to absorb is 6,261 J.
Calculation for heat:Heat required to raise the temperature of ice from -20 °C to 0 °C.
The formula for specific heat is used to calculate the amount of heat
Q = c * m * ΔT
Where,
Q =heat exchanged by a body,
m= mass of the body
c= specific heat
ΔT= change in temperature
Given:
m= 10 g,
specific heat of the ice= 2.1
ΔT=0 C - (-20 C)= 20 C
On substituting the values:
Q= 10 g*2.1 *20 C
Q=420 J
Heat required to convert 0 °C ice to 0 °C water.
The heat Q necessary to melt a substance depends on its mass m and on the called latent heat of fusion of each substance:
Q= m* ΔHfusion
Heat required to raise the temperature of water from 0 °C to 60 °C
m= 10 g,
Specific heat of the water= 4.18
ΔT=60 C - (0 C)= 60 C
On substituting:
Q= 10 g*4.18 *60 C
Q=2,508 J
Thus, Qtotal= 420 J + 3,333 J + 2,508 J
Qtotal= 6,261 J
The amount of heat to absorb is 6,261 J
Find more information about Specific heat here:
brainly.com/question/13439286
Heterocyclic aromatic compounds undergo electrophilic aromatic substitution in a similar fashion to that undergone by benzene with the formation of a resonance-stabilized intermediate. Draw all of the resonance contributors expected when the above compound undergoes bromination
Answer:
See explanation
Explanation:
When we talk about electrophilic substitution, we are talking about a substitution reaction in which the attacking agent is an electrophile. The electrophile attacks an electron rich area of a compound during the reaction.
The five membered furan ring is aromatic just as benzene. This aromatic structure is maintained during electrophilic substitution reaction. The attack of the electrophile generates a resonance stabilized intermediate whose canonical structures have been shown in the image attached.
A piece of solid Fe metal is put into an aqueous solution of Cu(NO3)2. Write the net ionic equation for any single-replacement redox reaction that may be predicted. Assume that the oxidation state of in the resulted solution is 2 . (Use the lowest possible coefficients for the reaction. Use the pull-down boxes to specify states such as (aq) or (s). If a box is not needed, leave it blank. If no reaction occurs, leave all boxes blank and click on Submit.)
Answer:
Fe(s) + Cu^2+(aq) ---> Fe^2+(aq) + Cu(s)
Explanation:
The ionic equation shows the actual reaction that took place. It excludes the spectator ions. Spectator ions are ions that do not really participate in the reaction even though they are present in the system.
For the reaction between iron and copper II nitrate, the molecular reaction equation is;
Fe(s) + Cu(NO3)2(aq)----> Fe(NO3)2(aq) +Cu(s)
Ionically;
Fe(s) + Cu^2+(aq) ---> Fe^2+(aq) + Cu(s)
What is the balanced equation for the reaction of aqueous cesium sulfate and aqueous barium perchlorate?
Answer:
The balanced chemical reaction is given as:
[tex]Cs_2SO_4(aq)+Ba(ClO_4)_2(aq)\rightarrow BaSO_4(s)+2CsClO_4(aq)[/tex]
Explanation:
When aqueous cesium sulfate and aqueous barium perchlorate are mixed together it gives white precipitate barium sulfate and aqueous solution od cesium perchlorate.
The balanced chemical reaction is given as:
[tex]Cs_2SO_4(aq)+Ba(ClO_4)_2(aq)\rightarrow BaSO_4(s)+2CsClO_4(aq)[/tex]
According to reaction, 1 mole of cesium sulfate reacts with 1 mole of barium perchlorate to give 1 mole of a white precipitate of barium sulfate and 2 moles of cesium perchlorate.
What is the final volume V2 in milliliters when 0.551 L of a 50.0 % (m/v) solution is diluted to 23.5 % (m/v)?
Answer:
[tex]V_2=1.17L[/tex]
Explanation:
Hello,
In this case, for dilution processes, we must remember that the amount of solute remains the same, therefore, we can write:
[tex]V_1C_1=V_2C_2[/tex]
Whereas V accounts for volume and C for concentration that in this case is %(m/v). In such a way, the final volume V2 turns out:
[tex]V_2=\frac{V_1C_1}{C_2}= \frac{0.551L*50.0\%}{23.5\%}\\ \\V_2=1.17L[/tex]
Best regards.
Write a balanced chemical equation for the base hydrolysis of methyl butanoate with NaOH. (Use either molecular formulas or condensed structural formulas, but be consistent in your equation.)
Explanation:
C5H10O2 + NaOH = C2H5COONa + C2H5OH
your result are : sodium propanoate and ethanol
A balanced chemical equation represents atoms and their numbers with their charge. The balanced equation for base hydrolysis is C₅H₁₀O₂ + NaOH → C₂H₅COONa + C₂H₅OH.
What is hydrolysis?Base hydrolysis is the splitting of the ester linkage by the basic molecule. As the result the acidic ester portion makes the salt, and also alcohol is produced as the by-product.
The base hydrolysis of methyl butanoate is shown as,
C₅H₁₀O₂ + NaOH → C₂H₅COONa + C₂H₅OH
Here, sodium propanoate and ethanol are produced by the splitting of methyl butanoate in the presence of the base (NaOH).
Therefore, C₅H₁₀O₂ + NaOH → C₂H₅COONa + C₂H₅OH is balanced reaction.
Learn more about hydrolysis here:
https://brainly.com/question/22078321
#SPJ2
When titrating a strong acid with a strong base, after the equivalence point is reached, the pH will be determined exclusively by: Select the correct answer below:
A) hydronium concentration
B) hydroxide concentration
C) conjugate base concentration
D) conjugate acid concentration
Answer:
B) hydroxide concentration
Explanation:
Hello,
In this case, since we are talking about strong both base and acid, since the base is the titrant and the acid the analyte, once the equivalence point has been reached, some additional base could be added before the experimenter realizes about it, therefore, since the titrant is a strong base, it completely dissociates in hydroxide ions and metallic ions which allows us to compute the pOH of the solution by known the hydroxide ions concentration.
After that, due to the fact that the pH is related with the pOH as shown below:
pH=14-pOH
We can directly compute the pH.
Best regards.
place the following substances in Order of decreasing boiling point H20 N2 CO
Answer:
-195.8º < -191.5º < 100º
Explanation:
Water, or H20, starts boiling at 100ºC.
Nitrogen, or N2, starts boiling at -195.8ºC.
Carbon monoxide, or C0, starts boiling at -191.5ºC.
When we place these in order from decreasing boiling point:
-195.8º goes first, then -191.5º, and 100º goes last.
Answer:
therefore, N2, CO, H20
Decreasing boiling point
Explanation:
the bond existing in H2O is hydrogen bond
bond existing in N2 is covalent bond, force existing is dipole-dipole-interaction
bond existing in CO is covalent bond , force existing between is induced -dipole- induced dipole-interaction
hydrogen bond is the strongest , followed by dipole-dipole-interaction and induced -dipole- induced dipole-interaction
the stronger the bond , the higher the boiling point
therefore, N2, CO, H20
-------------------------------------->
Decreasing boiling point
Refer to the figure.
30. How many planes are shown in the figure?
31. How many planes contain points B, C, and E?
32. Name three collinear points.
3. Where could you add point G on plane N
so that A, B, and G would be collinear?
4. Name a point that is not coplanar with
A, B, and C.
5. Name four points that are coplanar.
BN
Answer:
30. 5 planes are shown
31. 1 plane
32. CEF
33. on line AB
34. E or F
35. ABCD or BCEF or CDEF or ACEF
Explanation:
30. Each of the surfaces of the rectangular pyramid is a plane. There are 5 planes.
__
31. 3 points define one plane only.
__
32. The only points shown on the same line segment are points E, F, and C.
__
33. If G is to be collinear with A and B, it must lie on line AB.
__
34. The only points shown that are not on plane N are points E and F. Either of those will do.
__
35. There are three planes that have 4 points shown on them. The four points that are on the same plane are any of ...
ABCDBCEFCDEFPlane ACEF is not shown on the diagram, but we know that those 4 points are also coplanar. (Any point not on line CE, together with the three points on that line, will define a plane with 4 coplanar points.)
What is the ph of 0.36M HNO3 ?
Answer:
0.44
Explanation:
We know that the pH of any acid solution is given by the negative logarithm of its hydrogen ion concentration. Hence, if I can obtain the hydrogen ion concentration of any acid, I can obtain its pH.
For the acid, HNO3, [H^+] = [NO3^-]= 0.36 M
pH= -log [H^+]
pH= - log[0.36]
pH= 0.44
