Answer:
NaCl
Explanation:
If you follow traditional rounding, Na atomic mass is 23 and Cl atomic mass 35, 23 +35 = 58.
I was taught that Cl is one of the elements you round to 35.5, but this works if you’re not in an advanced chem class.
During a hurricane, what effect can the ocean have on the beach?
A.
Only the wind from a hurricane affects the land.
B.
Only the rain from a hurricane affects the land.
C.
The ocean can wash away much of the beach in a short time.
D.
The ocean always cleans litter from the beach during a hurricane.
8. Zeolite is used to remove moisture from methane. A vertical column is filled with 1000.0 kg of dry zeolite. The zeolite has the capacity to hold 0.100 kg water/kg dry zeolite. Once the zeolite becomes saturated with moisture, it must be regenerated by heating. The inlet moisture content of the methane is 7.00% (by mass) and the outlet moisture content is 0.05% (by mass). How much methane (kg) will be produced before the zeolite must be regenerated
Answer:
Follows are the solution to this question:
Explanation:
Methane inlet humidity content of [tex]=7.00\%[/tex]
Methane moisture outlet content [tex]=0.05\%[/tex]
Zeolite absorption humidity [tex]= 6.95\%[/tex]
Dry zeolite 1 kg will accommodate water[tex]= 0.1000 \ kg[/tex]
One kilogram of Dry Zeolite will carry water from [tex]=0.1000\ kg[/tex]
The water can contain 1000 kg of zeolite [tex]= 100 \ kg[/tex]
Methane which would be made [tex]=\frac{100}{6.95\%}= 1,439 \ kg[/tex]
That's why it will be producing 1439 kg of methane.
The amount of methane that can be produced before the regeneration of zeolite is 1,439 kg.
What is zeolite?
Zeolite belongs from the family of hydrated aluminosilicate minerals, in which alkali and alkaline earth metals are present.
In the question, it is given that:
Capacity of 1kg of zeolite to hold water = 0.100kg
Capacity of 1000kg of zeolite to hold water = 100kg
Inlet moisture content of the methane = 7.00 % (by mass)
Outlet moisture content of the methane = 0.05% (by mass)
Capacity of zeolite to absorb methane content = 6.95 %
Amount of methane before the regeneration of zeolite = 100kg / 6.95% = 14.39% of kg = 1,439 kg
Hence, 1,439 kg methane will be produced before the zeolite must be regenerated.
To know mote about zeolite, visit the below link:
https://brainly.in/question/1081379
which element is shown in the picture here?
The half-life of 226Ra is 1.60x103 years. How long until only 12.5% of the original sample of 226Ra remains?
Answer:
4.80×10³ years
Explanation:
Let the original amount (N₀) of ²²⁶Rn = 1 g
Therefore,
12.5% of the original amount = 12.5% × 1 = 12.5/100 × 1 = 0.125 g
Next, we shall determine the number of half-lives that has elapse. This can be obtained as follow:
Original amount (N₀) = 1
Amount remaining (N) = 0.125 g
Number of half-lives (n) =?
N = 1/2ⁿ × N₀
0.125 = 1/2ⁿ × 1
0.125 = 1/2ⁿ
Cross multiply
0.125 × 2ⁿ = 1
Divide both side by 0.125
2ⁿ = 1/0.125
2ⁿ = 8
Express 8 in index form with 2 as the base
2ⁿ = 2³
n = 3
Thus, 3 half-lives has elapsed.
Finally, we shall determine the time taken for only 12.5% of the original sample of ²²⁶Rn to remain.
This can be obtained as follow:
Half-life (t½) = 1.60×10³ years
Number of half-lives (n) = 3
Time (t) =?
t = n × t½
t = 3 × 1.60×10³
t = 4.80×10³ years.
Thus, it will take 4.80×10³ years for 12.5% of the original sample of ²²⁶Rn to remain.
Consider the following equilibrium
N204(9) - 2NO2(9) Keq = 5.85 x 10-3
Which statement about this system is true?
If the equilibrium concentration of NO2 is 1.78 x 10-2 M, the equilibrium concentration of N2O4 is
The equilibrium concentration of N₂O₄, given that the concentration of NO₂ is 1.78×10⁻² is 5.42×10⁻²
Data obtained from the question N₂O₄ <=> 2NO₂Equilibrium constant (Keq) = 5.85×10⁻³ Equilibrium concentration of NO₂ = 1.78×10⁻²Equilibrium concentration of N₂O₄ =?How to determine the equilibrium concentration of N₂O₄Keq = [Product] / [Reactant]
Keq = [NO₂]² / [N₂O₄]
5.85×10⁻³ = [1.78×10⁻²]² / [N₂O₄]
Cross multiply
5.85×10⁻³ × [N₂O₄] = [1.78×10⁻²]²
Divide both sides by 5.85×10⁻³
[N₂O₄] = [1.78×10⁻²]² / 5.85×10⁻³
[N₂O₄] = 5.42×10⁻²
Learn more about equilibrium constant:
https://brainly.com/question/17960050
#SPJ1
Answer:
First answer is "The equilibrium lies to the left", and the second one is 5.42 x 10^-2 M.
Explanation:
Hope i helped yall :D
How to balance NaOH+CO2=Na2CO3+H2O by algebraic method?
How many moles is equal 82.4 grams of CO,?
Answer:
1 mole = 28.0101
Hence,
82.4 = around 2.8 mole
Have a great day <3
what are the twa parts of central nervous system ?
Answer:
The nervous system has two main parts: The central nervous system is made up of the brain and spinal cord.
Explanation:
Neutralization Reactions
5. Acids and bases go to completion via neutralization reactions, thus titrations are applicable. Refer to educational resources and provide an example of the chemical reactions for the solutions in a–c.
a. A mixture between a strong acid and a strong base.
b. A strong base mixed with a weak acid.
c. A strong acid mixed with weak base.
Answer:
its a option neutralization takes place between acid and base plz mark me branliest
Heat flows from hotter objects to colder objects until it reaches a state where heat is no longer flowing.What have the objects reached when heat is not longer flowing?
__C+_SO2—_CS2 + __CO
Answer:
_c+_so2-_cs2+_co= Toxic
how many grams of hcl would be produced if 54 grams of water were used
Answer:
i dont know
Explanation:
its simple i dont know
Answer:
Explanation:Red
Given that C = n/V. And you have n=2 and C=4 what does V= ??
1...0.5
2...2
3...4
4...8
or5...Dont know
what career field/job would utilize ppm units
A environmental jobs
B Medical fields
C Jobs at the brewery
D Jobs in analytical chemistry
HELP FAST 75 PTS Calculate the amount of heat needed to melt 35.0 g of ice at 0 ºC. must show work
Answer:
It takes 12,000 Joules of energy to melt 35 grams of ice at 0 °C
Explanation:
Good Luck!
How many grams are in 1.2 x 10^24 atoms of sodium?
How much more acidic/more H+ concentration is a pH of 6 than pH of 8
*☆*――*☆*――*☆*――*☆*――*☆*――*☆*――*☆*――*☆**☆*――*☆*――*☆*――*☆
Answer: 1000x
Explanation:
I hope this helped!
<!> Brainliest is appreciated! <!>
- Zack Slocum
*☆*――*☆*――*☆*――*☆*――*☆*――*☆*――*☆*――*☆**☆*――*☆*――*☆*――*☆
A chemistry student is given 4.00 L of a clear aqueous solution at 22°C. He is told an unknown amount of a certain compound X is dissolved in the solution. The student allows the solution to cool to 22 C. The solution remains clear. He then evaporates all of the water under vacuum. A precipitate remains. The student washes, dries and weighs the precipitate. It weighs 0.56 kg.
Required:
Using only the information above, Calculate the solubility of X in water at 22° C. If you said yes, calculate it Be sure your answer has a unit symbol and 2 no .0 it. significant digits.
Answer:
The responses to the given points can be defined as follows:
Explanation:
In point 1:
The answer is "No".
In point 2:
The mass of solute = The mass of precipitate [tex]= 0.56\ kg =0.56\ \times 1000 = 560 \ g[/tex]
Calculating the solubility:
[tex]= \frac{\text{mass of solute in g}}{\text{volume of solution in ml}}\\\\ = \frac{560}{ 4000} \\\\ = 0.14 \ \frac{g}{ml}[/tex]
PLEASE HELP!!
A scientist places a pH meter in a sample of concentrated potassium hydroxide (KOH). The scientist slowly adds nitric acid (HNO3) to the KOH and monitors the pH. Describe how the pH and hydronium ion concentration will change in the solution as the acid is added.
Answer:
pH of the solution will decrease & hydronium ion concentration will increase in the solution as the acid is added.
Explanation:
Explain what method you would use to obtain
Petrol (boiling point 20
60 C) from a mature of petrol and kerosene (boiling point 180 220 C)
Answer:
Fractional distillation of crude oil in laboratory
Explanation:
In general, we can sort them according to their boiling point.
We should first place a ball of mineral wool soaked with petroleum into a boiling tube and heat it with a Bunsen flame. At the beginning of the experiment, heat the mineral with a gentle flame, and then more strongly later. The fraction with a lower boiling range will distil out first. Since petrol is quite volatile, it should be condensed by cooling with water or an ice-water bath.
Petrol will be collected first, as it has a lower boiling point than kerosene. It will turn into vapour and condense again in the receive tub in the beaker.
1. Chlorofluorocarbons (CFCs) are of interest because of their ability to destroy ozone molecules. A carbon-chlorine bon din the CFC molecule can be broken by sunlight, leaving a highly reactive free radical which then goes on to destroy the surrounding ozone molecules. The energy of a C-Cl bond is 328 kJ/mole. Calculate the wavelength of light needed to break a bond in a single molecule. In which region of the spectrum (infrared, visible, UV) does this wavelength fall
Answer:
See explanation
Explanation:
Energy of the photon (E) = 328 * 10^3/6.02 * 10^23 = 5.45 * 10^-19 J
Recall that E = hc/λ
h = Plank's constant = 6.36 * 10^-34 Js
c = speed of light = 3 * 10^8 m/s
λ = ??
λ = hc/E
λ = 6.36 * 10^-34 * 3 * 10^8/5.45 * 10^-19
λ = 3.5 * 10^-7 m
This falls into the UV region of the spectrum
32 g of a metal, M, reacts with 8 g of oxygen to form an oxide. The formula of the oxide is MO. What is the atomic mass of M in g mol-?
Answer: M= 128 g/mol (Te is quite close)
Explanation: number of Oxygen moles is n = 8 g / 32 g/mol = 0,25 mol.
Because formula of oxide is MO, thus amount of metal is also 0,25 mol.
Because n = m/M , Molar mass of the metal M = m/n = 32 g /0.25 mol = 128 g/ mol
Calculate the molarity of a solution that contains 3.00x10-2 mol NH4Cl in exactly 450 cm3 of solution.
Answer:
0.06moles/litres
Explanation:
molarity = no of moles / volume in litres = 3.00*10^-2/(450/1000)=0.06 moles/litres
Answer:
0.07mol/dm^3
Explanation:
Please mark as brainliest
What features did you use to classify igneous rocks as extrusive or intrusive ?
Answer: Igneous rocks may be simply classified according to their chemical/mineral composition as felsic, intermediate, mafic, and ultramafic, and by texture or grain size: intrusive rocks are course grained (all crystals are visible to the naked eye) while extrusive rocks may be fine-grained (microscopic crystals) or glass.
Explanation: Hope this helped! :)
Answer:
Igneous rocks may be simply classified according to their chemical/mineral composition as felsic, intermediate, mafic, and ultramafic, and by texture or grain size: intrusive rocks are course grained (all crystals are visible to the naked eye) while extrusive rocks may be fine-grained (microscopic crystals) or glass ( ...
An iron sulfide compound is analyzed, and found to contain 11.26 g iron and 9.70 g sulfur. Determine the molar ratio of sulfur to iron in this compound, and hence its chemical formula.
Answer:
Molar ratio = 1.5Chemical formula = Fe₂S₃Explanation:
First we convert the given masses of each element into moles, using their respective molar masses:
Fe ⇒ 11.26 g ÷ 55.845 g/mol = 0.202 mol FeS ⇒ 9.70 g ÷ 32.065 g/mol = 0.302 mol SNow we divide them in order to calculate the molar ratio of S to Fe:
0.302 / 0.202 = 1.5Meaning that for each 1 Fe mol, there's 1.5 S moles. We can write that as Fe₁S₁.₅
Finally we double those subscripts so that they become the lowest possible integers: Fe₂S₃.
As student used a pen to draw a line across a piece of chromatography paper. he then placed a sample of dye on the drawn line for analysis . is the student doing the right thing? why?
Answer is in the photo. I can only upload it to a file hosting service. link below!
tinyurl.com/wpazsebu
Help bestie pls help ASAP thank you
Explanation:
heyyyyyyyyy how are you sure
Do molecules move in all phases? (yes/no)
Answer: sorta
Explanation:
In fact, they do not flow at all: they simply vibrate back and forth. Because the atoms in a solid are so tightly packed, solid matter holds its shape and cannot be easily compressed
Which is a saturated solution?
A）40g NH4Cl in 100g water at 50°C
B）2g SOz in 100g water at 10°C
C）52g KCl in 100g water at 80°C
D）120g KI in 100g water at 20°C
Answer:
C）52g KCl in 100g water at 80°C
Explanation:
A saturated solution is one that contains as much solute as it can dissolve in the presence of excess solute at that particular temperature.
A solutibility curve is a graph that shows the variability with temperature of the solubility of a solute in a given solvent. A solutibility curve can provide information of whether a solution formed frommthe solute and solvent are saturated or not at a given temperature.
From the solubility curve in the attachment below:
A) A saturated solution of NH₄Cl will contain about 52 g solute per 100 g sat 50 °C. Thus, a solution of 40 g NH₄Cl in 100 g water at 50 °C is an unsaturated solution.
B) A saturated solution of SO₂ at 10°C will contain about 70 g of solute in 100 g of water. Thus a solution of 2g SO₂ in 100g water at 10°C is an unsaturated solution.
C) A saturated solution of KCl at 80 °C will contain about 52 g of solute in 100 g of water. Thus, a solution of 52g KCl in 100g water at 80°C is a saturated solution.
D) A saturated solution of Kl at 20 °C will contain about 145 g of solute in 100 g of water. Thus, a solution of 120g KI in 100g water at 20°C is an unsaturated solution.
how many atoms are in 0.5 mole of aluminum
According to the Avogadro's number, there are 3.011×10²³ atoms in 0.5 mole of aluminium.
What is Avogadro's number?Avogadro's number is defined as a proportionality factor which relates number of constituent particles with the amount of substance which is present in the sample.
It has a SI unit of reciprocal mole whose numeric value is expressed in reciprocal mole which is a dimensionless number and is called as Avogadro's constant.It relates the volume of a substance with it's average volume occupied by one of it's particles .
According to the definitions, Avogadro's number depend on determined value of mass of one atom of those elements.It bridges the gap between macroscopic and microscopic world by relating amount of substance with number of particles.
Number of atoms can be calculated using Avogadro's number as follows: mass/molar mass×Avogadro's number, on substituting values in formula, 0.5×6.023×10²³=3.011×10²³ atoms.
Thus, there are 3.011×10²³ atoms in 0.5 mole of aluminium.
Learn more about Avogadro's number,here:
https://brainly.com/question/11907018
#SPJ2
