Answer:
v = -v₀ / 2
Explanation:
For this exercise let's use kinematics relations.
Let's use the initial conditions to find the acceleration of the electron
v² = v₀² - 2a y
when the initial velocity is vo it reaches just the negative plate so v = 0
a = v₀² / 2y
now they tell us that the initial velocity is half
v’² = v₀’² - 2 a y’
v₀ ’= v₀ / 2
at the point where turn v = 0
0 = v₀² /4 - 2 a y '
v₀² /4 = 2 (v₀² / 2y) y’
y = 4 y'
y ’= y / 4
We can see that when the velocity is half, advance only ¼ of the distance between the plates, now let's calculate the velocity if it leaves this position with zero velocity.
v² = v₀² -2a y’
v² = 0 - 2 (v₀² / 2y) y / 4
v² = -v₀² / 4
v = -v₀ / 2
We can see that as the system has no friction, the arrival speed is the same as the exit speed, but with the opposite direction.
In 1.0 second, a battery charger moves 0.50 C of charge from the negative terminal to the positive terminal of a 1.5 V AA battery.
Part A:
How much work does the charger do? Answer is 0.75 J
Part B:
What is the power output of the charger in watts?
Answer:
W = Q * V work done on charge Q
A. W = .5 C * 1.5 V = .75 Joules
B. P = W / t = .75 J / 1 sec = .75 Watts
A grade 12 Physics student shoots a basketball
from the ground at a hoop which is 2.0 m above
her release. The shot was at a velocity of 10 m/s
and at an angle of 80° to the ground.
a. Determine the vertical velocity of the ball
when it is at the level of the net. You
should get two answers.
Please show ALL steps
Answer:
7.84 m/s
Explanation:
Height, h = 2 m
Initial velocity, u = 10 m/s
Angle, A = 80°
(a) Let the time taken to go to the net is t.
Use second equation of motion
[tex]h = u t + 0.5 at^2\\\\- 2 = - 10 sin 80 t - 4.9 t^2\\\\4.9 t^2 + 9.8 t - 2 = 0 \\\\t= \frac{- 9.8\pm\sqrt{9.8^2 + 4\times 4.9\times 2}}{9.8}\\\\t = \frac{- 9.8 \pm 11.6}{9.8}\\\\t = - 2.2 s , 0.2 s[/tex]
Time cannot be negative.
So, t = 0.2 s
The vertical velocity at t = 0.2 s is
v = u + at
v = 10 sin 80 - 9.8 x0.2
v = 9.8 - 1.96 = 7.84 m/s
Question 9 of 10
According to the law of conservation of momentum, the total initial
momentum equals the total final momentum in a(n)
A. Interacting system
B. System interacting with one other system
C. Isolated system
D. System of balanced forces
Answer:
The answer is C. Isolated System
Answer:
C. Isolated system
Explanation :
∵According to law of conservation of momentum ,In an isolated system ,the total momentum remains conserved.
A 100-W light bulb is left on for 20.0 hours. Over this period of time, how much energy did the bulb use?
Answer:
Power = Energy/time
Energy = Power xtime.
Time= 20hrs
Power = 100Watt =0.1Kw
Energy = 0.1 x 20 = 2Kwhr.
This Answer is in Kilowatt-hour ...
If the one given to you is in Joules
You'd have to Change your time to seconds
Then Multiply it by the power of 100Watts.
Assume that I = E/(R + r), prove that 1/1 = R/E + r/E
[tex]\implies {\blue {\boxed {\boxed {\purple {\sf { \frac{1}{I} = \frac{R}{E} + \frac{r}{E} }}}}}}[/tex]
[tex]\large\mathfrak{{\pmb{\underline{\orange{Step-by-step\:explanation}}{\orange{:}}}}}[/tex]
[tex]I = \frac{ E}{ R + r} \\[/tex]
[tex] ➺\:\frac{I}{1} = \frac{E}{R + r} \\[/tex]
Since [tex]\frac{a}{b} = \frac{c}{d} [/tex] can be written as [tex]ad = bc[/tex], we have
[tex]➺ \: I \: (R + r) = E \times 1[/tex]
[tex]➺ \: \frac{1}{I} = \frac{R + r}{E} \\ [/tex]
[tex]➺ \: \frac{1}{I} = \frac{R}{E} + \frac{r}{E} \\ [/tex]
[tex]\boxed{ Hence\:proved. }[/tex]
[tex]\red{\large\qquad \qquad \underline{ \pmb{{ \mathbb{ \maltese \: \: Mystique35ヅ}}}}}[/tex]
During a practice shot put throw, the 7.9-kg shot left world champion C. J. Hunter's hand at speed 16 m/s. While making the throw, his hand pushed the shot a distance of 1.4 m. Assume the acceleration was constant during the throw.
Required:
a. Determine the acceleration of the shot.
b. Determine the time it takes to accelerate the shot.
c, Determine the horizontal component of the force exerted on the shot by hand.
Answer:
a) a = 91.4 m / s², b) t = 0.175 s, c)
Explanation:
a) This is a kinematics exercise
v² = vox ² + 2a (x-xo)
a = v² - 0/2 (x-0)
let's calculate
a = 16² / 2 1.4
a = 91.4 m / s²
b) the shooting time
v = vox + a t
t = v-vox / a
t = 16 / 91.4
t = 0.175 s
c) let's use Newton's second law
F = ma
F = 7.9 91.4
F = 733 N
prove mathematically :
1. v = u + at
2. s = ut+1*2 at
Answer:
a.v=u+v/2
a.v=s/t
combining two equation we get,
u+v/2=s/t
(u+v)t/2=s
(u+v)t/2=s
{u+(u+at)}t/2=s
(u+u+at)t/2=s
(2u+at)t/2=s
2ut+at^2/2=s
2ut/2+at^2/2=s
UT +1/2at^2=s
proved
a=v-u/t
at=v-u
u+at=v
What is the energy equivalent of an object with a mass of 2.5 kg? 5.5 × 108 J 7.5 × 108 J 3.6 × 1016 J 2.25 × 1017 J
Answer:
E = m c^2 = 2.5 * (3 * 10E8)^2 = 2.25 * 10E17 Joules
Answer:
The answer is D. 2.25 × 1017 J
Explanation:
got it right on edge 2021
A cylindrical tank with radius 7 m is being filled with water at a rate of 2 m3/min. How fast is the height of the water increasing (in m/min)?
Answer:
0.013 m/min
Explanation:
Applying,
dV/dt = (dh/dt)(dV/dh)............. Equation 1
Where
V = πr²h................ Equation 2
Where V = volume of the tank, r = radius, h = height.
dV/dh = πr²............ Equation 3
Substitute equation 3 into equation 1
dV/dt = πr²(dh/dt)
From the question,
Given: dV/dt = 2 m³/min, r = 7 m, π = 3.14
Substitute these values into equation 3
2 = (3.14)(7²)(dh/dt)
dh/dt = 2/(3.14×7²)
dh/dt = 0.013 m/min
A 31 kg block is initially at rest on a horizontal surface. A horizontal force of 83 N is required to set the block in motion. After it is in motion, a horizontal force of 55 N i required to keep it moving with constant speed. From this information, find the coefficients of static and kinetic friction
Answer:
The static and kinetic coefficients of friction are 0.273 and 0.181, respectively.
Explanation:
By Newton's Laws of Motion and definition of maximum friction force, we derive the following two formulas for the static and kinetic coefficients of friction:
[tex]\mu_{s} = \frac{f_{s}}{m\cdot g}[/tex] (1)
[tex]\mu_{k} = \frac{f_{k}}{m\cdot g}[/tex] (2)
Where:
[tex]\mu_{s}[/tex] - Static coefficient of friction, no unit.
[tex]\mu_{k}[/tex] - Kinetic coefficient of friction, no unit.
[tex]f_{s}[/tex] - Static friction force, in newtons.
[tex]f_{k}[/tex] - Kinetic friction force, in newtons.
[tex]m[/tex] - Mass, in kilograms.
[tex]g[/tex] - Gravitational constant, in meters per square second.
If we know that [tex]f_{s} = 83\,N[/tex], [tex]f_{k} = 55\,N[/tex], [tex]m = 31\,kg[/tex] and [tex]g = 9.807\,\frac{m}{s^{2}}[/tex], then the coefficients of friction are, respectively:
[tex]\mu_{s} = \frac{83\,N}{(31\,kg)\cdot \left(9.807\,\frac{m}{s^{2}} \right)}[/tex]
[tex]\mu_{s} = 0.273[/tex]
[tex]\mu_{k} = \frac{55\,N}{(31\,kg)\cdot \left(9.807\,\frac{m}{s^{2}} \right)}[/tex]
[tex]\mu_{k} = 0.181[/tex]
The static and kinetic coefficients of friction are 0.273 and 0.181, respectively.
You need to calculate the volume of berm that has a starting cross-sectional area of 118 SF, and an ending cross-sectional area of 245 SF. The berm is 300 ft long and is assumed to taper evenly between the two cross-sectional areas, what is the calculated volume of the berm in cubic feet
The relation of mass m, angular velocity o and radius of the circular path r of an object with the centripetal force is-
a. F = m²wr
b. F = mwr²
c. F = mw²r
d. F = mwr.
Answer:
Correct option not indicated
Explanation:
There are few mistakes in the question. The angular velocity ought to have been denoted with "ω" and not "o" (as also suggested in the options).
The formula to calculate a centripetal force (F) is
F = mv²/r
Where m is mass, v is velocity and r is radius
where
While the formula to calculate a centrifugal force (F) is
F = mω²r
where m is mass, ω is angular velocity and r is radius of the circular path.
From the above, it can be denoted that the relationship been referred to in the question is that of a centrifugal force and not centripetal force, thus the correct option should be C.
NOTE: Centripetal force is the force required to keep an object moving in a circular path/motion and acts inward towards the centre of rotation while centrifugal force is the force felt by an object in circular motion which acts outward away from the centre of rotation.
A 0.060 kg ball hits the ground with a speed of –32 m/s. The ball is in contact with the ground for 45 milliseconds and the ground exerts a +55 N force on the ball.
What is the magnitude of the velocity after it hits the ground?
Answer:
9.25 m/s
Explanation:
1.- Que distancia recorrió una carga de 2,5x10-6 coul, generando así un campo eléctrico de 55new/coul.
Answer:
r = 20.22 m
Explanation:
Given that,
Charge,[tex]q=2.5\times 10^{-6}\ C[/tex]
Electric field, [tex]E=55\ N/C[/tex]
We need to find the distance. We know that, the electric field a distance r is as follows :
[tex]E=\dfrac{kq}{r^2}\\\\r=\sqrt{\dfrac{kq}{E}}\\\\r=\sqrt{\dfrac{9\times 10^9\times 2.5\times 10^{-6}}{55}}\\\\r=20.22\ m[/tex]
So, the required distance is 20.22 m.
A basketball of mass 0.608 kg is dropped from rest from a height of 1.37 m. It rebounds to a height of 0.626 m.
(a) How much mechanical energy was lost during the collision with the floor?
(b) A basketball player dribbles the ball from a height of 1.37 m by exerting a constant downward force on it for a distance of 0.132 m. In dribbling, the player compensates for the mechanical energy lost during each bounce. If the ball now returns to a height of 1.37 m, what is the magnitude of the force?
Answer:
a)[tex]|\Delta E|=4.58\: J[/tex]
b)[tex]F=61.90\: N[/tex]
Explanation:
a)
We can use conservation of energy between these heights.
[tex]\Delta E=mgh_{2}-mgh_{1}=mg(h_{2}-h_{1})[/tex]
[tex]\Delta E=0.608*9.81(0.6026-1.37)[/tex]
Therefore, the lost energy is:
[tex]|\Delta E|=4.58\: J[/tex]
b)
The force acting along the distance create a work, these work is equal to the potential energy.
[tex]W=\Delta E[/tex]
[tex]F*d=mgh[/tex]
Let's solve it for F.
[tex]F=\frac{mgh}{d}[/tex]
[tex]F=\frac{0.608*9.81*1.37}{0.132}[/tex]
Therefore, the force is:
[tex]F=61.90\: N[/tex]
I hope is helps you!
The 1 kg box is sliding along a frictionless surface. It collides with and sticks to the 2 kg box. Afterward, the speed of the two boxes is:__________.
A) 0 m/s
B) 1 m/s
C) 2 m/s
D) 3 m/s
E) Not enough info
Answer:
The correct option is (E).
Explanation:
Given that,
Mass of object 1, m₁ = 1 kg
Mass of object 2, m₂ = 2 kg
They collides after the collision. We need to find the speed of the two boxes after the collision.
The initial speeds of both boxes is not given. So, we can't put the values of their speeds in the momentum conservation equation.
So, the information is not enough.
Two spheres are rolling without slipping on a horizontal floor. They are made of different materials, but each has mass 5.00 kg and radius 0.120 m. For each the translational speed of the center of mass is 4.00 m/s. Sphere A is a uniform solid sphere and sphere B is a thin-walled, hollow sphere. Part B How much work, in joules, must be done on the solid sphere to bring it to rest? Express your answer in joules. VO AE4D ? J WA Request Answer Submit Part C How much work, in joules, must be done on the hollow sphere to bring it to rest? Express your answer in joules. Wa Request
Answer:
Explanation:
Moment of inertia of solid sphere = 2/5 m R²
m is mass and R is radius of sphere.
Putting the values
Moment of inertia of solid sphere I₁
Moment of inertia of hollow sphere I₂
Kinetic energy of solid sphere ( both linear and rotational )
= 1/2 ( m v² + I₁ ω²) [ ω is angular velocity of rotation ]
= 1/2 ( m v² + 2/5 m R² ω²)
= 1/2 ( m v² + 2/5 m v²)
=1/2 x 7 / 5 m v²
= 0.7 x 5 x 4² = 56 J .
This will be equal to work to be done to stop it.
Kinetic energy of hollow sphere ( both linear and rotational )
= 1/2 ( m v² + I₂ ω²) [ ω is angular velocity of rotation ]
= 1/2 ( m v² + 2/3 m R² ω²)
= 1/2 ( m v² + 2/3 m v²)
=1/2 x 5 / 3 m v²
= 0.833 x 5 x 4² = 66.64 J .
This will be equal to work to be done to stop it.
a vessel with mass 10kg intially moving withthe velocicity 12m s along the x axis explodes into three exactly identical pieces Just after the explosion one piece moves with speed 10 m s along the x axis and asecond piece moves with speed 10 m s along the y axis What iis the magnitude of the component of velocity of the third piece along the y axiss
Answer:
Explanation:
Apply law of conservation of momentum along y-axis.
Initially there was no momentum along y-axis. So there will be nil momentum along y-axis again finally.
Let the mass of each piece after breaking be m .
Momentum of piece moving along positive y-axis
= m x 10 = 10m .
Let the component of velocity of third piece along y-axis be v .
Its momentum along the same direction = m v .
Total momentum along y -axis = 10 m + m v
According to law of conservation of momentum
10 m + mv = 0
v = - 10 m/s .
Component of velocity of the third piece along y-axis will be - 10 m/s .
In other words it will be along negative y-axis with speed of 10 m/s.
Is the actual height the puck reached greater or less than your prediction? Offer a possible reason why this might be.
Answer:
Answer to the following question is as follows;
Explanation:
The puck's real altitude is lower than ones projection. That's because the mechanism may not be completely frictionless. Electricity is nevertheless wasted owing to particle interactions such as friction, which might explain why the present the results is lower than predicted.
Help me with my physics, please
In the figure, particle A moves along the line y = 31 m with a constant velocity v with arrow of magnitude 2.8 m/s and parallel to the x axis. At the instant particle A passes the y axis, particle B leaves the origin with zero initial speed and constant acceleration a with arrow of magnitude 0.35 m/s2. What angle between a with arrow and the positive direction of the y axis would result in a collision?
Answer:
59.26°
Explanation:
Since a is the acceleration of the particle B, the horizontal component of acceleration is a" = asinθ and the vertical component is a' = acosθ where θ angle between a with arrow and the positive direction of the y axis.
Now, for particle B to collide with particle A, it must move vertically the distance between A and B which is y = 31 m in time, t.
Using y = ut + 1/2a't² where u = initial velocity of particle B = 0 m/s, t = time taken for collision, a' = vertical component of particle B's acceleration = acosθ.
So, y = ut + 1/2a't²
y = 0 × t + 1/2(acosθ)t²
y = 0 + 1/2(acosθ)t²
y = 1/2(acosθ)t² (1)
Also, both particles must move the same horizontal distance to collide in time, t.
Let x be the horizontal distance,
x = vt (2)where v = velocity of particle A = 2.8 m/s and t = time for collision
Also, using x = ut + 1/2a"t² where u = initial velocity of particle B = 0 m/s, t = time taken for collision, a" = horizontal component of particle B's acceleration = asinθ.
So, x = ut + 1/2a"t²
x = 0 × t + 1/2(ainsθ)t²
x = 0 + 1/2(asinθ)t²
x = 1/2(asinθ)t² (3)
Equating (2) and (3), we have
vt = 1/2(asinθ)t² (4)
From (1) t = √[2y/(acosθ)]
Substituting t into (4), we have
v√[2y/(acosθ)] = 1/2(asinθ)(√[2y/(acosθ)])²
v√[2y/(acosθ)] = 1/2(asinθ)(2y/(acosθ)
v√[2y/(acosθ)] = ytanθ
√[2y/(acosθ)] = ytanθ/v
squaring both sides, we have
(√[2y/(acosθ)])² = (ytanθ/v)²
2y/acosθ = (ytanθ/v)²
2y/acosθ = y²tan²θ/v²
2/acosθ = ytan²θ/v²
1/cosθ = aytan²θ/2v²
Since 1/cosθ = secθ = √(1 + tan²θ) ⇒ sec²θ = 1 + tan²θ ⇒ tan²θ = sec²θ - 1
secθ = ay(sec²θ - 1)/2v²
2v²secθ = aysec²θ - ay
aysec²θ - 2v²secθ - ay = 0
Let secθ = p
ayp² - 2v²p - ay = 0
Substituting the values of a = 0.35 m/s, y = 31 m and v = 2.8 m/s into the equation, we have
ayp² - 2v²p - ay = 0
0.35 × 31p² - 2 × 2.8²p - 0.35 × 31 = 0
10.85p² - 15.68p - 10.85 = 0
dividing through by 10.85, we have
p² - 1.445p - 1 = 0
Using the quadratic formula to find p,
[tex]p = \frac{-(-1.445) +/- \sqrt{(-1.445)^{2} - 4 X 1 X (-1)}}{2 X 1} \\p = \frac{1.445 +/- \sqrt{2.088 + 4}}{2} \\p = \frac{1.445 +/- \sqrt{6.088}}{2} \\p = \frac{1.445 +/- 2.4675}{2} \\p = \frac{1.445 + 2.4675}{2} or p = \frac{1.445 - 2.4675}{2} \\p = \frac{3.9125}{2} or p = \frac{-1.0225}{2} \\p = 1.95625 or -0.51125[/tex]
Since p = secθ
secθ = 1.95625 or secθ = -0.51125
cosθ = 1/1.95625 or cosθ = 1/-0.51125
cosθ = 0.5112 or cosθ = -1.9956
Since -1 ≤ cosθ ≤ 1 we ignore the second value since it is less than -1.
So, cosθ = 0.5112
θ = cos⁻¹(0.5112)
θ = 59.26°
So, the angle between a with arrow and the positive direction of the y axis would result in a collision is 59.26°.
A generator is designed to produce a maximum emf of 190 V while rotating with an angular speed of 3800 rpm. Each coil of the generator has an area of 0.016 m2. If the magnetic field used in the generator has a magnitude of 0.052 T, how many turns of wire are needed
Answer:
The number of turns of wire needed is 573.8 turns
Explanation:
Given;
maximum emf of the generator, = 190 V
angular speed of the generator, ω = 3800 rev/min =
area of the coil, A = 0.016 m²
magnetic field, B = 0.052 T
The number of turns of the generator is calculated as;
emf = NABω
where;
N is the number of turns
[tex]\omega = 3800 \frac{rev}{min} \times \frac{2\pi}{1 \ rev} \times \frac{1 \min}{60 \ s } = 397.99 \ rad/s[/tex]
[tex]N = \frac{emf}{AB\omega } \\\\N = \frac{190}{0.016 \times 0.052\times 397.99} \\\\N = 573.8 \ turns[/tex]
Therefore, the number of turns of wire needed is 573.8 turns
ACCORDING TO NEWTON'S THIRD LAW EVERY ACTION HAS EQUAL AND OPPOSITE REACTION BUT THEN WHY DON'T WE FLY WHEN WE FART??
Answer:
Your fart only has so much force, not nearly enough to launch you into oblivion. Your fart and you still exert a force onto each other, so I guess, hypothetically, you could fly if you really, really try hard enough. Just make sure you don't try too hard and prolapse as a result :)
two resistors with resistance values 4.5 ohms and 2.3 ohms are connected in series or parallel across a potential difference of 30V to a light bulb find the current flowing through the light bulb in both cases
Answer:
Look at work
Explanation:
Series:
I is the same for all resistors so just find the value of Req. In series Req= R1+R2+...+Rn. So here it will be 4.5+2.3=6.8ohms. Ieq=Veq/Req=4.41A. And since current is the same across all resistors the current to the lightbulb is 4.41A.
Parallel:
V is the same for all resistors so start of by finding Req. In parallel, Ieq=I1+I2+...+In. So I1= 30/4.5= 6.67A and I2= 13.04A. Ieq= 6.67+13.04= 19.71A.
Define relative density.
Relative density is the ratio of the density of a substance to the density of a given material.
Three spheres (water, iron and ice) of the exact same volume are submerged in a tub of water. After the spheres are lined up, they are released. The spheres are made of plastic with the same density as water, ice, and iron.
Required:
a. Compare the weights of the three spheres.
b. Compare the buoyant forces on the three spheres.
c. What direction does the net force push on each of the spheres?
d. What happens to each sphere after it is released?
Answer:
(a) Iron > plastic > ice
(b) Same on all
(c) Iron downwards, plastic net force zero, ice upwards.
(d) Iron sphere sinks, plastic sphere is in equilibrium and ice sphere will floats.
Explanation:
Three spheres have same volume , plastic, ice and iron.
(a) The weight is given by
Weight = mass x gravity = volume x density x gravity
As the density of iron is maximum and the density of ice is least so the order of the weight is
Weight of iron > weight of plastic > weight of ice
(b) Buoyant force is given by
Buoyant force = Volume immersed x density of fluid x g
As they have same volume, density of fluid is same so the buoyant force is same on all the spheres.
(c) Net force is
F = weight - buoyant force
So, the net force on the iron sphere is downwards
On plastic sphere is zero as the density of plastic sphere is same as water. On ice sphere it is upwards.
(d) Iron sphere sinks, plastic sphere is in equilibrium and ice sphere will floats.
a microwave operates at a frequency of 2400 MHZ. the height of the oven cavity is 25 cm and the base measures 30 cm by 30 cm. assume that microwave energy is generated uniformly on the uipper surface. What is the power output of the oven
Complete question is;
A microwave oven operates at a frequency of 2400 MHz. The height of the oven cavity is 25 cm and the base measures 30 cm by 30 cm. Assume that microwave energy is generated uniformly on the upper surface of the cavity and propagates directly
downward toward the base. The base is lined with a material that completely absorbs microwave energy. The total microwave energy content of the cavity is 0.50 mJ.
Answer:
Power ≈ 600,000 W
Explanation:
We are given;
Frequency; f = 2400 Hz
height of the oven cavity; h = 25 cm = 0.25 m
base area; A = 30 cm by 30 cm = 0.3m × 0.3m = 0.09 m²
total microwave energy content of the cavity; E = 0.50 mJ = 0.5 × 10^(-3) J
We want to find the power output and we know that formula for power is;
P = workdone/time taken
Formula for time here is;
t = h/c
Where c is speed of light = 3 × 10^(8) m/s
Thus;
t = 0.25/(3 × 10^(8))
t = 8.333 × 10^(-10) s
Thus;
Power = (0.5 × 10^(-3))/(8.333 × 10^(-10))
Power ≈ 600,000 W
A transverse sine wave with an amplitude of 2.50 mm and a wavelength of 1.80 m travels, from left to right along a long, horizontal stretched string with a speed of 36.0 m s. I Take the origin at the left end of the undisturbed string. At time t = 0 the left end of the string has its maximum upward displacement,
(a) What is the frequency of the wave?
(b) What is the angular frequency of the wave?
(c) What is the wave number of the wave?
(d) What is the function y(x,t) that describes the wave?
(e) What is y(t) for a particle at the left end of the string?
(f) What is y(t) for a particle 1.35 m to the right of the origin?
(g) What is the maximum magnitude of transverse velocity of any particle of the string?
(h) Find the transverse displacement of a particle 1.35 m to the right of the origin at time t = 0.0625 s.
(i) Find the transverse velocity of a particle 1.35 m to the right of the origin at time t = 0.0625 s.
Explanation:
Given that,
Amplitude, A = 2.5 nm
Wavelength,[tex]\lambda=1.8\ m[/tex]
The speed of the wave, v = 36 m/s
At time t = 0 the left end of the string has its maximum upward displacement.
(a) Let f is the frequency. So,
[tex]f=\dfrac{v}{\lambda}\\\\f=\dfrac{36}{1.8}\\\\f=20\ Hz[/tex]
(b) Angular frequency of the wave,
[tex]\omega=2\pi f\\\\=2\pi \times 20\\\\=125.7\ rad/s[/tex]
(c) The wave number of the wave[tex]=\dfrac{1}{\lambda}[/tex]
[tex]=\dfrac{1}{1.8}\\\\=0.56\ m^{-1}[/tex]
The outer surface of a spacecraft in space has an emissivity of 0.44 and a solar absorptivity of 0.3. If solar radiation is incident on the spacecraft at a rate of 950 W/m2, determine the surface temperature of the spacecraft when the radiation emitted equals the solar energy absorbed.
Answer:
[tex]T=326.928K[/tex]
Explanation:
From the question we are told that:
Emissivity [tex]e=0.44[/tex]
Absorptivity [tex]\alpha =0.3[/tex]
Rate of solar Radiation [tex]R=0.3[/tex]
Generally the equation for Surface absorbed energy is mathematically given by
[tex]E=\alpha R[/tex]
[tex]E=0.3*950[/tex]
[tex]E=285W/m^2[/tex]
Generally the equation for Emitted Radiation is mathematically given by
[tex]\mu=e(\sigmaT^4)[/tex]
Where
T=Temperature
[tex]\sigma=5.67*10^8Wm^{-2}K_{-4}[/tex]
Therefore
[tex]\alpha*E=e \sigma T^4[/tex]
[tex]0.3*(950)=0.44(5.67*10^-8)T^4[/tex]
[tex]T=326.928K[/tex]
A rope, under a tension of 221 N and fixed at both ends, oscillates in a second-harmonic standing wave pattern. The displacement of the rope is given by y = (0.10 m)(sin πx/2) sin 12πt, where x = 0 at one end of the rope, x is in meters, and t is in seconds.
What are:
a. the length of the rope.
b. the speed of the waves on the rope
c. the mass of the rope
d. If the rope oscillates in a third-harmonic standing wave pattern, what will be the period of oscillation.
Answer:
sup qwertyasdfghjk
Explanation:
