If the pressure exerted on the floor by a box is 200kpa, find the weight of the box given that the bottom of the box has a contact area of 20cm³?​

Answers

Answer 1
Basically the pressure times area gives the force applies by the box on the floor which is its weight.
So, F = 2 x 20 x 10^5 x 10^-6 N = 4N
So the weight is 4 Newtons
Answer 2

The weight of the box is approximately 0.0408 kg.

What is Pressure?

Pressure is a measure of how much force is applied per unit area of surface. It is a scalar quantity and has units of force per unit area. It is typically expressed in units such as pascals (Pa), atmospheres (atm), or pounds per square inch (psi).

We can use the formula:

pressure = force / area

where pressure is given as 200 kPa and area is given as 20 cm^2. Converting cm^2 to m^2:

20 cm^2 = 20 x 10^-4 m^2 = 0.002 m^2

Substituting the values in the formula and solving for force:

200 kPa = force / 0.002 m^2

force = 200 kPa x 0.002 m^2

force = 0.4 kN (kilonewtons)

The weight of the box is the force acting on it due to gravity, which is given by:

weight = mass x gravitational acceleration

Assuming the box is on the Earth's surface, we can use a value of 9.81 m/s^2 for gravitational acceleration. Solving for mass:

mass = weight / gravitational acceleration

mass = 0.4 kN / 9.81 m/s^2

mass = 0.0408 kg (kilograms)

Therefore, the weight of the box is approximately 0.0408 kg.

Learn more about Pressure from given link

https://brainly.com/question/28012687

#SPJ1


Related Questions


How would you ensure that the food you have prepared remains hot till you reach to hospital?​

Answers

Employ heat packs to keep food warm during delivery. To keep the food as warm as possible and the heat packs well-insulated, place them directly in the bag with the food containers.

Can someone check my answers? If I’m incorrect can you correct me? Thank you. Image below.

Answers

Refer to the attached image.

Overall: Parts (a) and (c) need to be corrected.

imagine that the blue light and orange light from the source were blocked. what color would how be present in the spectrum of light observed

Answers

Everything but blue & orange would now be present in the spectrum of light observed.

Spectrum refers to a range of different wavelengths of electromagnetic radiation. Electromagnetic radiation is a form of energy that travels through space and includes different types such as radio waves, microwaves, infrared radiation, visible light, ultraviolet radiation, X-rays, and gamma rays. Each type of electromagnetic radiation has a different wavelength and frequency, and together they make up the electromagnetic spectrum.

The concept of spectrum is used in a variety of fields, including physics, astronomy, and telecommunications. The spectrum of electromagnetic radiation is essential for many technologies, such as radios and televisions, cell phones, and medical imaging devices, as they all rely on the transmission and reception of specific wavelengths of electromagnetic radiation.

To learn more about Spectrum visit here:

brainly.com/question/11837978

#SPJ4

Complete Question: -

Imagine that the blue light and orange light from the source were blocked. What color(s) would now be present in the spectrum of light observed?

1.- What is net net charge on the sweater? Why?
2.- What is the net charge on the balloon? Why?

ASAP pls and thank you!!

Answers

When students brush balloons against their wool sweaters or hair, electrons are moved from the wool or hair to the balloon. As a result, the balloon has a net negative charge, whereas the garment or hair, having shed negative charges, has a net positive charge.

What is net charge?

The term "net" refers to the sum after both positive and negative costs have been deducted. So, if something has 321 positive charges and 319 negative charges, the overall charge is 321 - 319 = +2. The overall charge is 37 - 42 = -5 if it includes 37 positive charges and 42 negative charges.

Electrons are negatively charged, whereas protons are favourably charged. Atoms have an identical amount of electrons and protons and have a net charge of zero. This makes atoms always neutral.

Learn more about net charge

https://brainly.com/question/30196320

#SPJ1

Two blocks of unequal mass are tied together with a massless string that does not stretch and connected via a frictionless and massless pulley. Mass one, M1, rests on a frictionless table top. Mass two, M2, is released and both blocks begin to move....
The blocks accelerate at the same rate since they are connected. What is the acceleration?

Answers

The blocks accelerate at the same charge for the reason that they're linked. The acceleration is a value between zero and g.

Acceleration is a physical concept that refers to the rate of change of an object's velocity with respect to time. When an object's velocity changes, either by speeding up or slowing down, it is said to be accelerating.

Acceleration plays an important role in many aspects of physics, from the motion of celestial bodies to the behavior of particles in a particle accelerator.  The magnitude of acceleration is the rate at which an object's velocity changes, and it is measured in units of meters per second squared (m/s^2) in the International System of Units (SI). There are several factors that can cause an object to accelerate, such as a force acting on it, a change in its direction of motion, or a combination of both.

To learn more about Acceleration visit here:

brainly.com/question/30660316

#SPJ4

lonie is being pulled from a snake pit with a rope that breaks if tension in it exceeds 755N. If one has a mass of 70kg and the snake pit is 3 Am deep, what is the minimum time necessary to pull out lonie?

Answers

The minimum time required to pull out lonie from the snake pit is √(3/4) seconds.

Given: Mass, m = 70 kg Distance, d = 3 m Limiting tension, T = 755N

The minimum time required to pull out lonie from a snake pit, t

Given, mass, m = 70 kg Acceleration due to gravity, g = 9.8 m/s²Distance, d = 3 m

Let's assume the minimum time required to pull out lonie from a snake pit is t.

So, using the equation of motion,S = ut + 1/2 at²

Here, S = d = 3m (Distance),u = 0 m/s (Initial velocity),a = g = 9.8 m/s² (Acceleration) and t = time

Substituting the above values in the equation, we get3 = 0 + 1/2 × 9.8 × t² => t² = 3/4 => t = √(3/4) sec

Also, we know that the tension in the rope is given byT = mg + ma

Now, the rope will break when T exceeds 755 N.

So, substituting the values of m, g, and a in the above equation, we getT = mg + ma = 70 × 9.8 + 70 × a

Since the tension in the rope should be less than or equal to 755 N, we have70 × 9.8 + 70 × a ≤ 755 => a ≤ (755 - 70 × 9.8)/70=> a ≤ 3.29 m/s²

Therefore, the minimum time required to pull out lonie from the snake pit is √(3/4) seconds.

for such more question on minimum time

https://brainly.com/question/14517981

#SPJ11

when a ray of light hits a surface, the angles made by the reflection and refraction of the ray must all be measured from the normal, which is

Answers

When a ray of light hits a surface, the angles made by the reflection and refraction of the ray must all be measured from the normal, which is perpendicular to the surface at the point where the light ray hits it.

Reflection occurs when light rays hit a surface and bounce back whereas Refraction, occurs when light travels through a medium of a different density or refractive index.

The laws of reflection and refraction states that the angle of incidence is equal to the angle of reflection, and the ratio of the sine of the angle of incidence to the sine of the angle of refraction is constant. This ratio is known as the refractive index of the material from where the light is passing through.

To know more about reflection and refraction refer to:

brainly.com/question/16957723

#SPJ4

3. Large amplitude vibrations produced when the of receiver of the applied forced vibration matches the

Answers

An object's amplitude dramatically increases when the frequency of the applied forced vibrations matches the object's natural frequency. Resonance describes this behavior.

Theory A wave's amplitude directly relates to the quantity of energy it can carry. A wave with a high amplitude carries a lot of energy, whereas one with a low amplitude carries only a little. A wave's strength is determined by the typical energy that moves through a given area in a certain amount of time and in a particular direction.The sound wave's amplitude grows in proportion to its strength. We perceive louder noises to be of higher intensity. Comparative sound intensities are frequently expressed using decibels (dB)

For more information on amplitude of vibration kindly visit to

https://brainly.com/question/1380029

#SPJ1

Select the correct answer. In a given chemical reaction, the energy of the products is greater than the energy of the reactants. Which statement is true for this reaction? A. Energy is absorbed in the reaction. B. Energy is released in the reaction. C. No energy is transferred in the reaction. D. Energy is created in the reaction. E. Energy is lost in the reaction. Reset Next

Answers

A - energy is absorbed during the reaction

moving water can be used as an energy source. select all the characteristics of this energy source that apply.

Answers

The above-listed characteristics apply to moving water as an energy source. Thus, moving water can be used as an energy source.

The following are the characteristics of moving water as an energy source:

It is a renewable energy source. It is a clean energy source. It is available in many different forms. It is the least expensive energy source to generate.

Water is an excellent resource for producing electricity since it is clean, renewable, and is available in many different forms. When water moves, it has the potential to generate energy, which can be harnessed in several ways to produce electricity. As a result, moving water is an excellent source of renewable energy, as it is available in many different forms and can be used in a variety of ways.The above-listed characteristics apply to moving water as an energy source. Thus, moving water can be used as an energy source.

for such more question on energy source

https://brainly.com/question/19887979

#SPJ11

an electron is moving parallel to an electric field (from higher to lower voltage). its potential energy is

Answers

The potential energy of an electron moving parallel to an electric field decreases as it moves from higher voltage to lower voltage. The work done by the electric field on the electron is equal to the decrease in potential energy. The potential energy of the electron is proportional to its charge and the voltage difference between the two points.

When an electron moves parallel to an electric field, its potential energy is conserved. The potential energy of an electron is proportional to its charge and the voltage through which it moves. As the electron moves from higher voltage to a lower voltage, its potential energy decreases. The work done by the electric field on the electron is equal to the decrease in potential energy. When the electron is at rest, it has a certain potential energy due to its position in the electric field. If the electron is allowed to move freely, it will accelerate towards the lower voltage region, gaining kinetic energy. As it moves, the electric field continues to do work on the electron, converting its potential energy into kinetic energy. If the electric field is uniform, the potential energy of the electron will be given by the equation U = -qV, where q is the charge of the electron and V is the voltage difference between the two points. The negative sign indicates that the potential energy decreases as the voltage difference decreases.

To learn more about Potential energy :

https://brainly.com/question/21175118

#SPJ11

A 120-kN truck has an engine that transmits a power of 380 kW to all the wheels. If the wheels do not slip on the ground, determine the angle of the largest incline the truck can climb at a constant speed of 72 km/h.

Answers

To determine the angle of the largest incline the truck can climb at a constant speed of 72 km/h, we need to use the formula for power, which is P = Fv, where P is the power, F is the force, and v is the velocity.

What is the equation for the maximum incline angle as ?

Since the velocity is constant, the force required to maintain this speed up an incline is equal to the force of gravity acting on the truck, which is given by Fg = mg, where m is the mass of the truck and g is the acceleration due to gravity.

Thus, we can write the equation for the maximum incline angle as:

sinθ = Fg/F

where θ is the angle of the incline. Substituting the given values, we get:

sinθ = (mg)/Pv

sinθ = (120000 kg)(9.81 m/s²)

sinθ =( 0.157)/(380000 W)(20 m/s)

θ = 9.04 degrees

Therefore, the angle of the largest incline the truck can climb at a constant speed of 72 km/h is approximately 9.04 degrees.

To know more about constant speed , visit :

https://brainly.com/question/24909693

#SPJ1

The maximum angle of incline the truck can climb at a constant speed of 72 km/h without slipping is approximately 18.3 degrees.

calculation of the question :-

First, we need to calculate the force required to maintain a constant speed of 72 km/h on an incline. We can use the following formula:

Force = weight * sin(theta) + rolling resistance + air resistance

where weight is the weight of the truck, theta is the angle of the incline, rolling resistance is the force required to overcome the friction between the wheels and the ground, and air resistance is the force required to overcome air resistance.

Since the wheels do not slip on the ground, the rolling resistance is equal to the weight of the truck multiplied by the coefficient of rolling resistance, which is typically around 0.01. Air resistance is typically negligible at lower speeds, so we can ignore it in this case.

Let's assume the weight of the truck is 120 kN and the coefficient of rolling resistance is 0.01. We can now calculate the force required to maintain a constant speed of 72 km/h on an incline:

Force = 120 kN * sin(theta) + 0.01 * 120 kN

Next, we need to determine the power required to produce this force. We can use the following formula:

Power = force * speed

where speed is the speed of the truck in meters per second. Since the speed of the truck is 72 km/h, or 20 m/s, we can calculate the power required:

Power = (120 kN * sin(theta) + 0.01 * 120 kN) * 20 m/s

Now we can use the given engine power of 380 kW to determine the maximum angle of incline:

380 kW = (120 kN * sin(theta) + 0.01 * 120 kN) * 20 m/s

Simplifying this equation, we get:

sin(theta) = (380 kW / (120 kN * 20 m/s)) - 0.01

sin(theta) = 0.3167

Taking the inverse sine of both sides, we get:

theta = sin^-1(0.3167) = 18.3 degrees

Therefore, the maximum angle of incline the truck can climb at a constant speed of 72 km/h without slipping is approximately 18.3 degrees.

To know more about Speed visit :-

https://brainly.com/question/13943409

#SPJ1

A compact car can climb a hill in 10 s. The top of the hill is 30 m higher than the bottom, and the car’s mass is 1,000 kg What is the power output of the car?

Answers

Answer:

the power output of the car is 29.43 kW (rounded to two decimal places).

Explanation:

To find the power output of the car, we need to use the formula:

power = work / time

where work is the change in potential energy of the car as it climbs the hill, which can be calculated using the formula:

work = force x distance

where force is the force required to lift the car against gravity, which is given by:

force = mass x gravity

where mass is the mass of the car, and gravity is the acceleration due to gravity (9.81 m/s^2).

So, the force required to lift the car against gravity is:

force = 1000 kg x 9.81 m/s^2 = 9810 N

The distance the car travels up the hill is 30 m.

Therefore, the work done by the car is:

work = force x distance = 9810 N x 30 m = 294300 J

The time taken by the car to climb the hill is 10 s.

Therefore, the power output of the car is:

power = work / time = 294300 J / 10 s = 29430 W

5.32 calculate ix and vo in the circuit of fig. 5.70. find the power dissipated by the 60-k resisto

Answers

The power dissipated by the 60-k Ohm resistor is 3 mv and 24mv.

[tex]=V_1=V =4mv\\=I_{iN}=\frac{4mv}{10k}=0.4\mu A\\= \frac{V_1 - V+}{50k}=0.4\mu A\\V_1 - 4m= 20m\\V_1 = 24mv[/tex]

[tex]i_x=\frac{V_1}{20+(6 || 3)} =\frac{24*10^{-3}}{(20+2.857)*10^{3}}\\i_x=1.05\mu A\\i_0=\frac{i_x*60}{60+3}=1\mu A\\V_0=3k*1\mu=3mv\\V_0=3mv[/tex]

An Ohm resistor is a passive electrical component that restricts the flow of current in an electrical circuit. It is named after Georg Simon Ohm, a German physicist who discovered Ohm's law which states that the current flowing through a conductor between two points is directly proportional to the voltage across the two points.

An Ohm resistor has a resistance value measured in ohms, which determines how much it restricts the flow of current. The higher the resistance value, the more it restricts the current flow. Ohm resistors are commonly used in electronic circuits to control the voltage and current levels, and to protect sensitive electronic components from damage. They can also be used to divide voltages, as voltage dividers, or as current limiting devices.

To learn more about Ohm resistor visit here:

brainly.com/question/1495664

#SPJ4

Complete Question: -

Calculate i_x and v_o in the circuit of Fig. 5.70. Find the power dissipated by the 60-k Ohm resistor.

if ao is 50 feet, find the perimeter of the pool. (o is the center of the sector aob. oa and ob are the diameters of two semi-circles.)

Answers

The perimeter of the pool is approximately 206.85 feet if we use 3.14 as the approximation of the value of π.

In this case, the angle AOB is 360 degrees, so the arc length is:

arc length = (360/360) x 2π(25) = 50π feet

Finally, we can find the perimeter of the pool by adding up the lengths of the two semicircles and the arc AB:

perimeter = 2πr + 2r + arc length

perimeter = 2π(25) + 2(25) + 50π

perimeter = 50π + 50

Perimeter is a measurement of the distance around the edge of a two-dimensional shape, such as a square, rectangle, or circle. It is the sum of the lengths of all the sides that make up the shape. The perimeter is an important concept in geometry and is used to determine the amount of material needed to enclose or surround a shape, as well as to calculate the distance around a given route or path.

To find the perimeter of a shape, you simply add up the lengths of its sides. For example, if you have a square with sides that are each 5 units long, the perimeter would be 5 + 5 + 5 + 5 = 20 units. Similarly, if you have a circle with a radius of 10 units, the perimeter (also known as the circumference) would be 2πr or approximately 62.8 units.

To learn more about Perimeter visit here:

brainly.com/question/30252651

#SPJ4

Complete Question: -

If AO is 50 feet, find the perimeter of the pool. (O is the center of the sector AOB. OA and OB are the diameters of two semi-circles.)

is the amount by which the total run that conduit can cover is reduced because of the extra length required to bend around an obstacle.

Answers

Bending allowance is the amount by which the total run that conduit can cover is reduced because of the extra length required to bend around an obstacle.

When running conduit, bending is necessary to go around obstructions like structural members or corners. In order to avoid the use of too many fittings and to make installation faster and more efficient, it is best to avoid angles less than 30 degrees.
When measuring conduit length, it is important to include the bending allowance. The length of the conduit required can be calculated using the following formula:
Bending allowance = (Conduit diameter x bending angle) x 0.0175
Where,
Bending allowance is the additional length of the conduit needed to make the bend.
Conduit diameter is the diameter of the conduit being used.
Bending angle is the angle of the bend being made.
0.0175 is the constant factor used in this calculation.
For example, suppose we have to bend a 1.5-inch diameter conduit around a corner with a 45-degree angle. The bending allowance for this conduit would be:
Bending allowance = (1.5 x 45) x 0.0175
Bending allowance = 1.4 inches
So, when measuring the length of the conduit required for this bend, 1.4 inches should be added to the length of the conduit required to make up for the bending allowance.

The amount by which the total run that conduit can cover is reduced because of the extra length required to bend around an obstacle is called the bending allowance.

For similar question on Bending

https://brainly.com/question/16107975

#SPJ11

Question:-

___ is the amount by which the total run that conduit can cover is reduced because of the extra length required to bend around an obstacle.

Complete the following statement: The polarization direction of an electromagnetic wave is determined by the wavelength of the electromagnetic radiation. the direction of the magnetic field component the direction of the electric field component the direction the wave is traveling. the frequency of the electromagnetic radiation.

Answers

The polarization direction of an electromagnetic wave is determined by the direction of the electric field component.

What is an electric field ?

Electromagnetic waves consist of oscillating electric and magnetic fields that are perpendicular to each other and to the direction of the wave's propagation. The direction of the electric field component determines the polarization direction of the wave. The electric field component oscillates perpendicular to the direction of propagation and determines the orientation of the electromagnetic wave.

In contrast, the wavelength, frequency, and direction of travel of the electromagnetic wave do not affect the polarization direction of the wave. However, the wavelength and frequency of the wave are related to its energy and momentum.

To know more about electric field, visit:

https://brainly.com/question/15800304

#SPJ1

Complete statement is: The polarization direction of an electromagnetic wave is determined by the direction of the electric field component.

b) what is the probability that an average of 22 shields will absorb more than 17.1 j/kg? use 4 decimal places.

Answers

The probability that an average of 22 shields will absorb more than 17.1 J/kg is approximately 0.3085.

where X is the random variable representing the energy absorbed per kilogram of the shield.

To calculate this probability, we need to know the distribution of X.

From the given information, we know that X follows a normal distribution with mean μ = 16.8 J/kg and standard deviation σ = 0.6 J/kg.

Thus, we can standardize X as follows:

Z = (X - μ)/σZ ~ N(0, 1)

P(X > 17.1) = P((X - μ)/σ > (17.1 - μ)/σ)

                = P(Z > (17.1 - 16.8)/0.6)

                = P(Z > 0.5)

Using a standard normal table, we can find the probability that Z > 0.5 to be 0.3085 (rounded to 4 decimal places).

Therefore, the probability that an average of 22 shields will absorb more than 17.1 J/kg is approximately 0.3085.

for such more question on probability

https://brainly.com/question/13604758

#SPJ11

The compressions in a sound wave are far apart and more energy is supplied by the vibrating source. Which statement best describes how this will affect the wave and what you hear?

A: The wavelength will increase, and the sound will become louder.
B: The amplitude will increase, and the sound will become louder.
C: The frequency will increase, and the pitch will become higher.
D: The intensity will increase, and the pitch will become higher.

Answers

The sound will get louder and the amplitude will rise. The separation between compressions in a sound wave indicates that the wave's wavelength has grown.

What happens when a sound wave is compressed and rarefied?

When particles travel in close proximity to one another, compression occurs, creating areas of intense pressure. In contrast, when particles are separated from one another in low-pressure locations, rarefactions take place. As the tines of a vibrating tuning fork move back and forth, compressions and rarefactions are produced.

What does it signify when a longitudinal wave's compressions are spaced widely apart?

Compressions and rarefactions are terms used to describe where a medium's particle distribution spreads out farther from one another.

To know more about amplitude visit:-

https://brainly.com/question/13110234

#SPJ1

The outer edge of a rotating Frisbee with a diameter of 30 cm has a linear speed of 3.2 m/s

What is the angular speed of the Frisbee? In rad/s

Answers

The angular speed of the Frisbee is 21.33 rad/s.

What is Angular speed ?

Angular speed is a measure of how fast an object is rotating or moving around a central point or axis. It is a scalar quantity, which is defined as the rate of change of the object's angular displacement over time, expressed in units of radians per second (rad/s).

Angular speed is calculated using the formula:

Angular speed (ω) = Δθ / Δt

The linear speed of the outer edge of the Frisbee is given by:

v = 3.2 m/s

The diameter of the Frisbee is given by:

d = 30 cm = 0.3 m

The radius of the Frisbee is half the diameter:

r = d/2 = 0.15 m

The linear speed of a point on the edge of a rotating object is related to the angular speed by the formula:

v = ωr

where ω is the angular speed in radians per second.

Substituting the given values, we can solve for ω:

ω = v/r

ω = 3.2 m/s / 0.15 m

ω = 21.33 rad/s (rounded to two decimal places)

Therefore, the angular speed of the Frisbee is 21.33 rad/s.

To know more about diameter visit:-

https://brainly.com/question/23220731

#SPJ1

Find the equivalent resistance of the combination shown in Figure 4, assuming that
R5 = 17 Ω and R6 = 26 Ω.

Answers

Answer:

Explanation:

R/^5*r^6 Ok so  then this is simple once u get the answer u need to use the given formula in order to plug in the numbres sorry .

So basically

12 x r^6(u must fill in the number s ) and then u need to do `13x14xr the answer and use the rest of the numbers in order to figure out the quantities of each side for the shape . Then ur answer would be the r^x + x = ???

So yeah hope this helped

I think

Kind of

K Thanks Bye

Three loads are applied attached at B and D. Neglecting the weight of the beam, determine the range of values of Q for which neither cable becomes slack when P = 0. as shown to a light beam supported by cables 7.5 kN Q P С E А В 1.5 m- 0.75 m 0.5 m 0.75 m Fig. P4.9

Answers

When[tex]P = 0, Q[/tex]must be in the range between [tex]4.3 kN and 12.9 kN[/tex] to prevent either cable from becoming slack.

We may examine the forces operating on the beam to find the range of values for Q. The sum of the vertical forces must be zero when [tex]P = 0,[/tex]which indicates that the beam is in equilibrium. Our result is the equation:

[tex]Q + 7.5 - 3 - 4 = 0[/tex]

When Q is solved for, we obtain [tex]Q = 0.5 kN to 12.9 kN.[/tex] To prevent either wire from going slack, we must also ensure that both cables are under positive stress. We can accomplish this by searching for the extreme values of Q in each cable's tensions.

[tex]Q = 0.5 kN[/tex]results in a positive 7.5 kN tension in cable AB. However, cable DE's tension is negative[tex](-2.5 kN)[/tex], indicating that cable DE is under tension. is loose.

[tex]Q = 12.9 kN[/tex] results in a positive [tex]3.4 kN[/tex] tension in cable DE. Cable AB, however, has negative tension [tex](-5.4 kN),[/tex] indicating that it is slack.

The range of Q values that satisfy the requirement that neither cable sags when [tex]P = 0 is 4.3 kN to 12.9 kN.[/tex]

learn more about cables here:

https://brainly.com/question/14300574

#SPJ4

Suppose a NASCAR race car rounds one end of the Martinsville Speedway. This end of the track is a turn with a radius of approximately 57.0 m . If the track is completely flat and the race car is traveling at a constant 27.5 m/s (about 62 mph ) around the turn, what is the race car's centripetal (radial) acceleration? What is the Coefficient of friction?

Answers

Answer:

Explanation:

The centripetal acceleration of the race car is given by the formula:

a = v^2 / r

where v is the speed of the race car and r is the radius of the turn.

Substituting the given values, we get:

a = (27.5 m/s)^2 / 57.0 m = 13.3 m/s^2

So the centripetal acceleration of the race car is 13.3 m/s^2.

To find the coefficient of friction, we need to use the formula:

f = μN

where f is the force of friction, μ is the coefficient of friction, and N is the normal force.

The normal force is equal to the weight of the car, which we can calculate as:

N = mg

where m is the mass of the car and g is the acceleration due to gravity (9.81 m/s^2).

Assuming the mass of the car is 1500 kg, we get:

N = 1500 kg × 9.81 m/s^2 = 14,715 N

The force of friction is equal to the centripetal force required to keep the car moving in a circle:

f = ma = (1500 kg)(13.3 m/s^2) = 19,950 N

Substituting the values of N and f into the formula for friction, we get:

19,950 N = μ(14,715 N)

Solving for μ, we get:

μ = 1.35

So the coefficient of friction is 1.35.

Estimat the number and wattage of lamps. which would be required to illuminate a workshop space 60x1.5 meteres by means of lamps mounted 5 metres above the working Plane The average illumination required is about 100 wt. coefficient of utilisation = 0.4 luminous efficiency 16 lumens per watt. Assume a space-height ratio of unity and a cundle Power depreciation of 20%​

Answers

The number and wattage of lamps required to illuminate the workshop would be approximately 8 lamps and 70 watts respectively.

Wattage calculation

To estimate the number and wattage of lamps required to illuminate a workshop space of 60x1.5 meters, we can follow these steps:

Calculate the area of the workshop:

Area = length x widthArea = 60m x 1.5mArea = 90 square meters

Determine the total lumens required:

Lumens = area x average illuminationLumens = 90 sq m x 100 luxLumens = 9000 lumens

Adjust for the coefficient of utilization and luminous efficiency:

Effective lumens = lumens / (coefficient of utilization x luminous efficiency)Effective lumens = 9000 / (0.4 x 16)Effective lumens = 1406.25 lumens

Adjust for space-height ratio and candle power depreciation:

Effective lumens per lamp = effective lumens x space-height ratio x (1 - depreciation)Effective lumens per lamp = 1406.25 x 1 x (1 - 0.2)Effective lumens per lamp = 1125 lumens

Determine the number of lamps required:

Number of lamps = total lumens required / effective lumens per lampNumber of lamps = 9000 / 1125Number of lamps = 8 lamps (rounded up)

Determine the wattage of each lamp:

Wattage per lamp = effective lumens per lamp / luminous efficiencyWattage per lamp = 1125 / 16Wattage per lamp = 70.3 watts (rounded up)

Therefore, approximately 8 lamps with a wattage of 70 watts each would be required to illuminate the workshop space.

More on wattage can be found here: https://brainly.com/question/14667843

#SPJ1

on the grid below sketch at least one complete cycle of a transverse wave with a 4.0 centimeter amplitude a freuqncy of 5.0 hertz

Answers

Draw the complete cycle of the wave by repeating the pattern of the peak, the equilibrium position, and the trough, with a distance of λ between each consecutive peak or trough. The number of cycles per second, or the frequency, should be 5.0 hertz.

What is Wave?

A wave is a disturbance that propagates through space and time, often transferring energy from one location to another without the physical transfer of matter. Waves can take many different forms, including sound waves, electromagnetic waves, and mechanical waves.

Draw a horizontal axis representing time, labeled in seconds or milliseconds.

Draw a vertical axis representing displacement or amplitude, labeled in centimeters or meters.

Choose a starting point for the wave, which represents the equilibrium position of the medium.

Draw the peak of the wave, which represents the maximum displacement of the medium from its equilibrium position. This should be 4.0 centimeters above the equilibrium position.

Draw the trough of the wave, which represents the minimum displacement of the medium from its equilibrium position. This should be 4.0 centimeters below the equilibrium position.

Determine the wavelength of the wave, which is the distance between two consecutive peaks or troughs. This can be calculated using the formula λ = v/f, where λ is the wavelength, v is the velocity of the wave, and f is the frequency. For a transverse wave on a string, the velocity is given by v = √(T/μ), where T is the tension in the string and μ is the linear mass density of the string.

Learn more about Wave from the given link

https://brainly.com/question/25699025

#SPJ1

Determine the absolute pressure on the bottom of a swimming pool 28.0 m by 8.5 m whose uniform depth is 1.8 m .
Express your answer using two significant figures.

Answers

The absolute pressure on the bottom of a swimming pool 28.0 m by 8.5 m whose uniform depth is 1.8 m is 287 kPa

the absolute pressure on the bottom of the pool is 17.6 kPa.

Pressure is defined as the amount of force per unit area applied to an object's surface. Pressure may also be defined as a scalar amount of stress exerted on a surface that is perpendicular to the direction of the force. Pressure is frequently represented by the symbol p, which stands for pressure.

Given,

Length of the pool, l = 28 m

Width of the pool, w = 8.5 m

Depth of the pool, h = 1.8 m

The density of water,

p = 1000 kg/m³

g = 9.81 m/s²

Absolute pressure formula:

p = ρgh

Absolute pressure p is given by,

p = ρgh

p = 1000 kg/m³ × 9.81 m/s² × 1.8 mp

  = 17604 Pa

Then, Converting the answer to kPa,

1 Pa = 1 × 10⁻³ kPa⇒ 17604 Pa = 17.6 kPa

Therefore, the absolute pressure on the bottom of the pool is 17.6 kPa rounded to two significant figures.

for such more question on  pressure

https://brainly.com/question/28012687

#SPJ11

A metal wire, fixed at one end, has length l and cross-sectional area A. The wire extends a distance e which mass m is hung from the other end of the wire.What is an expression for the Young Modulus E of the metal?

Answers

The expression for the Young Modulus E of the metal is E = mgl / Ae. The Young Modulus E of the metal is calculated using the equation  E = (F l) / (A e2 m), where F is the force applied to the wire.


To find the expression for the Young modulus E of a metal wire with length l, cross-sectional area A, and mass m hung from the other end of the wire, we need to use the following formula:Stress (σ) = Load (F) / Area (A)Strain (ε) = Extension (Δl) / Original length (l)Young Modulus (E) = Stress (σ) / Strain (ε)We know that the metal wire is fixed at one end and the wire extends a distance e when a mass m is hung from the other end of the wire. Therefore, the extension Δl is equal to e.

Let's assume that g is the acceleration due to gravity. Therefore, the load F is equal to m * g.Substituting the values of F, A, and Δl in the above formula, we get:Stress (σ) = F / A = (m * g) / AStrain (ε) = Δl / l = e / lYoung Modulus (E) = Stress (σ) / Strain (ε)= (m * g) / (A * e / l) = mgl / AeTherefore, an expression for the Young Modulus E of the metal is E = mgl / Ae.

For more such questions on metal

https://brainly.com/question/10537765

#SPJ11

125cm³ of a gas was collected at 15 °C and 755 mm of mercury pressure. Calculate the volume of the gas that will be collected at standard temperature and pressure

Answers

Answer:

119,2 см³

Explanation:

по формуле Клопейрона (P1×V1):T1=(P2×V2):T2

если из этой формулы найти V2, ответ будет равен примерно на 119,2 см³

A beam consisting of five types of ions labeled A, B, C, D, and E enters a region that contains a uniform magnetic field as shown in the figure below. The field is perpendicular to the plane of the paper, but its precise direction is not given. All ions in the beam travel with the same speed. The table below gives the masses and charges of the ions. Note: 1 mass unit = 1.67 x 10â€"27 kg and e = 1.6 x 10â€"19 C
Which ion falls at position 2?

Answers

At position 2, ion B falls. It is less deflected because it has a lesser mass than ions C, D, and E and the same charge as ion A.

A force perpendicular to the charged particle's velocity and the magnetic field's direction is applied when it reaches the magnetic field. The right-hand rule asserts that the palm will face the direction of the force if the thumb of the right hand points in the direction of the particle's velocity and the fingers point in the direction of the magnetic field. The particle's charge, velocity, and magnetic field intensity all affect how much force is generated.

Since all ions are moving at the same speed in this scenario, the force exerted on each ion is proportional to its charge to mass ratio. Ion B has the smallest mass of all the ions, so the least force and is least deflected of the ions, falling at position 2.

learn more about mass here:

https://brainly.com/question/19694949

#SPJ4

clock a remains in place and clock b is carried around the earth ( 40,000 km). by how many seconds will is clock b slower if carried on

Answers

Clock a remains in place and clock b is carried around the earth (40,000 km). According to Einstein's theory of relativity, The clock b is slower by approximately 44.6 seconds.

According to Einstein's theory of relativity, time dilation takes place when an object moves at a velocity close to the speed of light. The closer the velocity is to the speed of light, the more time slows down. This is why time on Earth is slower at high altitudes than it is on the ground.

According to the theory, the same effect happens when objects are moving at a high speed, which is why clocks that are taken on an airplane, for example, appear to be ticking more slowly.

1. The following equation is used to determine the time dilation:

t = t0 / √(1 – v²/c²),

where t is the time elapsed, t0 is the time at rest, v is the velocity, and c is the speed of light. When the earth rotates on its axis, every point on the planet's surface moves at a different velocity, with the highest velocity at the equator, and the velocity decreases as we move towards the poles. The earth's circumference at the equator is roughly 40,000 kilometers (24,901 miles).
As a result, a person standing on the equator would be traveling at a speed of around 1,674 kilometers per hour (1,040 miles per hour) because the earth spins once every 24 hours. We must first determine the velocity of a point on the earth's surface at the equator before we can use the equation to calculate time dilation.

2. We use the formula

v = 2πr / T,

where v is velocity, r is the radius of the earth, and T is the time it takes the earth to complete one rotation. The formula is as follows:

v = 2πr / Tv

= 2 x 3.14 x 6,378 km / 24 hv

= 1,674 km/h

3. Substituting these values into the equation, we get:

t = t0 / √(1 – v²/c²)t = t0 / √(1 – (1,674 m/s)² / (299,792,458 m/s)²)t = t0 / √(1 – 2.8 x 10^-8)t = t0 / 0.9999999714

This means that the clock on the equator will tick slightly slower than it would at rest. The difference in time can be calculated by subtracting the two values:

t – t0 = t0 / 0.9999999714 – t0t – t0 = t0 (1 – 0.9999999714)t – t0 = 0.0000000286 t0

4. We must first calculate the amount of time elapsed on the equator if a clock b is carried 40,000 km around the earth. It is easy to calculate the distance and speed, but we must also consider that the earth is rotating as well. As a result, we must determine the combined speed of the earth's rotation and the motion of clock b relative to the earth's surface.

5. To calculate this combined velocity, we can use the Pythagorean theorem, which states that the square of the hypotenuse of a right triangle is equal to the sum of the squares of the other two sides. If we imagine the velocity of the earth's rotation as the base of the triangle and the velocity of clock b as the height of the triangle, we can use this theorem to calculate the combined velocity as follows:

combined velocity = √(1,674² + vclock²)

where v clock is the velocity of clock b. Since clock b is being transported at the equator, it has the same velocity as the earth's rotation. As a result, we can substitute 1,674 km/h for v clock:

combined velocity = √(1,674² + 1,674²)

combined velocity = √(2 x 1,674²)

combined velocity = 2,367 km/h

6. Substituting the combined velocity into the equation for time dilation, we obtain:

t – t0 = t0 (1 – √(1 – v²/c²))t – t0 = t0 (1 – √(1 – (2,367 km/h)² / (299,792,458 m/s)²))t – t0

= t0 (1 – √(1 – 1.579 x 10^-11))t – t0

= t0 (1 – 0.999999999920215)t – t0

= 0.000000000079785 t0

Converting this value to seconds, we get:

0.000000000079785 t0 = 79.785 ns

Now we can combine the time dilation for the earth's rotation and the motion of clock b to obtain the total time dilation:

t – t0 = 0.0000000286 t0 + 0.000000000079785 t0t – t0 = 0.000000028679785 t0

Substituting the value of t0 (one second) into the equation, we get:

t – 1 = 0.000000028679785 seconds

Therefore, clock b will be approximately 44.6 seconds slower than clock a after being carried 40,000 km around the earth.

For more such questions on Einstein's theory of relativity , Visit:

https://brainly.com/question/3489672

#SPJ11

Other Questions
True or false: Given the popularity of the Internet, mobile devices, and the complexity of computer technologies, important business information and IT assets are exposed to risks and attacks from external parties such as hackers, foreigners, competitors, etc. Today's employees are well trained and always support the firm to prevent the attacks. Consider the following silica gel TLC plate of compounds A, B, and C developed in hexanes:Consider the following silica gel TLC plate of coma) Determine the R f values of compounds A, B, and C run on a silica gel TLC plate using hexanes as the solventb) Which compound, A, B, or C, is the most polar?c) What would you expect to happen to the R f values if you used acetone instead of hexanes as the eluting solvent? (Think polarity of solvents) which of the following statements may be true regarding a biochemical oxidation-reduction (redox) reaction? when performing regression, why would you want to have a quadratic term? group of answer choices you never want to add a quadratic term when performing regression to better fit a scatterplot with too many outliers to better fit a scatterplot that shows a curve in the data to better fit linear data Calculatethe LCM of 5 and 20 which of the following are generally considered to be the important trends that are becoming evident in the marketing research industry? (check all that apply.)- A broader international client base- Expanded use of digital technology to acquire and retrieve information- Movement toward technology-related data management write down the name of shape W Commercially available large wind turbines blade span diameters larger than 100 m and over 3 MW of electric power at peak design have generate conditions. Consider a wind turbine with a 75-m blade span subjected to 25-km/h steady winds. If the combined turbinegenerator effi- ciency of the wind turbine is 32 percent, determine (a) the power generated by the turbine and (b) the horizontal force exerted by the wind on the supporting mast of the turbine. Take the density of air to be 1.25 kg/m3, and disregard frictional effects on the mast. When a series of goals are set by the company with input from the employee, and the employee receives payment as each goal is reached, this is called a ____ In order to compute equivalent units of production, which of the following must be reasonably estimated?A) Units completedB) The percentage of completionC) Direct material costD) Units started and completedE) None of the above Part y Wa g on, Inc., provides musical entertainment at weddings, dances, and various other functions. The company performs adjusting entries monthly but prepares closing entries annually on December 31. The company recently hired Jack Armstrong as its new accountant. Jacks first assignment was to p re p are an income statement, a statement of retained earnings, and a balance sheet usin g an adjusted trial balance given to him by his predecessor, dated December 31, the current year.From the ad j usted trial balance, Jack p re p ared the followin g set of financial statements. Which of the following factors is unique for each substance when calculating the energy change associated with a change in temperature?A) massB) enthalpyC) temperature changeD) specific heat just prior to performing a compulsive action, a small majority of individuals with ocd experience feelings of . !!!50 points!!!Problem 1. What masses of 15% and 20% solutions are needed to prepare 200 g of 17% solution?Problem 2. What masses of 18% and 5% solutions are needed to prepare 300 g of 7% solution?Problem 3. 200 g of 15% and 350 g of 20% solutions were mixed. Calculate mass percentage of final solution.Problem 4. 300 g of 15% solution and 35 g of solute were mixed. Calculate mass percentage of final solution.Problem 5. 400 g of 25% solution and 150 g of water were mixed. Calculate mass percentage of final solution. Adapted from Other than the requirement that has been underlined in the passage, describe TWO other (2x1) criteria that are required in order to be considered for a bachelor degree studies. Find the value of 2 - 3x when x = 72 - 3x is a(n)__________. Please need help in math camille knew that her boss was going to be furious when he learned that she hadn't met her sales quota. rather than face his ire, she quickly arranged a business trip that so she would be out of the office for several days and hoped he'd have cooled off when she returned. which style of conflict resolution is camille using? In a single-flash geothermal power plant, geothermal water enters the flash chamber (a throttling valve) at 230C as a saturated liquid at a rate of 50 kg/s. The steam resulting from the flashing process enters a turbine and leaves at 20 kPa with a moisture content of 5 percent. Determine the temperature of the steamafter the flashing process and the power output from the turbine if the pressure of the steam at the exit of the flash chamber (2) is 1 MPa PLS HELP FAST 50 POINTS + BRAINLIEST