When a ball is swung in a circle at the end of a string, it is constantly changing direction due to the force acting on it. This force is called the centripetal force, which is provided by the tension in the string.
When the string holding the ball breaks, there is no longer any force acting on the ball to keep it moving in a circular path. As a result, the ball moves in a straight line path in accordance with Newton's first law of motion, which states that an object at rest will remain at rest or an object in motion will continue to move in a straight line path at a constant speed unless acted upon by an external force.
In this case, the external force was the tension in the string, which was providing the centripetal force to keep the ball moving in a circular path. Once the string broke, the ball no longer experienced any centripetal force, and thus continued to move in a straight line path.
To learn more about centripetal force refer to:
brainly.com/question/11324711
#SPJ4
Given the definition of EER, find the EER of an 8000 Btu/hour air conditioner that requires a power input of 1500 W. Express your answer numerically in British thermal units per hour per watt. EER = __________(Btu/hour)/W
EER is defined as the Energy Efficiency Ratio which is the ratio of cooling capacity in BTU/hr to the power input in watts.
The EER of the given 8000 Btu/h air conditioner is 5.33 Btu/hour per watt.
In the case of the given 8000 Btu/h air conditioner that requires a power input of 1500 W, the EER can be calculated as follows:
EER = (cooling capacity in Btu/hr) / (power input in watts)
EER = 8000 Btu/hour / 1500 W = 5.33 Btu/hour per wat.
Energy efficiency ratio (EER) is used in the USA and is defined as the system output in Btu/h per watt of electrical energy.
Coefficient of performance (COP) is the equivalent measure using SI units, which is widely used in the UK. A COP of 1.0 equates to an EER of 3.4.
To know more about power:https://brainly.com/question/11569624
#SPJ11
4. Once the child in the sample problem reaches the bottom of the hill,
she continues sliding along flat; snow-covered ground until she comes
to a stop. If her acceleration during this time is -0.392 m/s², how long
does it take her to travel from the bottom of the hill to her stopping
point?
Answer:
8.04 seconds
Explanation:
Assuming that the child starts from rest at the bottom of the hill and travels until she comes to a stop, we can use the following kinematic equation:
v_f^2 = v_i^2 + 2ad
where v_f is the final velocity (which is zero since the child comes to a stop), v_i is the initial velocity (which is the velocity at the bottom of the hill), a is the acceleration (-0.392 m/s²), and d is the distance traveled.
We can solve for d:
d = (v_f^2 - v_i^2) / (2a)
= (0 - v_i^2) / (2-0.392)
= v_i^2 / 0.784
Since the child is sliding along flat snow-covered ground, there is no change in elevation, so we can use the distance traveled from the bottom of the hill to the stopping point as the distance d.
To find the time it takes for the child to travel this distance, we can use the following kinematic equation:
d = v_it + 0.5a*t^2
where t is the time and all other variables are as previously defined.
Substituting the expression for d obtained above, we get:
v_i^2 / 0.784 = v_it + 0.5(-0.392)*t^2
Solving for t, we get:
t = (2 * v_i) / 0.392
We still need to find the value of v_i, the initial velocity of the child at the bottom of the hill. To do so, we can use conservation of energy. The child starts at rest at the top of the hill, so all the initial energy is potential energy. At the bottom of the hill, all the potential energy has been converted to kinetic energy. Assuming no energy is lost to friction, we can equate these two energies:
mgh = 0.5mv_i^2
where m is the mass of the child, g is the acceleration due to gravity (9.8 m/s²), and h is the height of the hill.
Solving for v_i, we get:
v_i = √(2gh)
Substituting this expression for v_i into the expression for t obtained earlier, we get:
t = (2 * √(2gh)) / 0.392
Plugging in the values of g, h, and a, we get:
t = (2 * √(29.820)) / 0.392 = 8.04 seconds
A typical neutron star has a mass of about 1.5Msun and a radius of 10 kilometers Calculate the average density of a neutron star. Express your answer in kilograms per cubic centimeter to two significant figures.
The average density of the neutron star that has a mass of about 1.5Msun and a radius of 10 kilometers rounded off to two significant figures is 5.9 × 10¹⁴ kg/cm³
The average density of a neutron star can be calculated using the following formula;`d = (3M)/(4πr³)`where `d` is the average density of the neutron star, `M` is the mass of the neutron star, and `r` is the radius of the neutron star.Using the given values in the formula, we get;`d = (3 × 1.5 × 1.989 × 10³⁰)/(4π × (10 × 10³)³)` = 5.9 × 10¹⁷ kg/m³To convert kg/m³ to kg/cm³, we can use the following conversion factor;1 m³ = 10⁶ cm³Therefore,1 kg/m³ = 10⁻³ kg/cm³So, the average density of the neutron star in kg/cm³ is;`d = (5.9 × 10¹⁷) × (10⁻³)` = 5.9 × 10¹⁴ kg/cm³Therefore, the average density of the neutron star is 5.9 × 10¹⁴ kg/cm³ (rounded to two significant figures).Answer: 5.9 × 10¹⁴ kg/cm³.
More on density: https://brainly.com/question/15700804
#SPJ11
Assume the motions and currents mentioned are along the x axis and fields are in the y direction.
(a) Does an electric field exert a force on a stationary charged object?
YesNo
(b) Does a magnetic field do so?
YesNo
(c) Does an electric field exert a force on a moving charged object?
YesNo
(d) Does a magnetic field do so?
YesNo
(e) Does an electric field exert a force on a straight current-carrying wire?
YesNo
(f) Does a magnetic field do so?
YesNo
(g) Does an electric field exert a force on a beam of moving electrons?
YesNo
(h) Does a magnetic field do so?
YesNo
(a) Yes, an electric field can exert a force on a stationary charged object. A stationary charged object will experience a force in the direction of the electric field due to the Coulombic interaction between the charges.
(b) No, a magnetic field does not exert a force on a stationary charged object. A stationary charged object does not experience a force due to a magnetic field unless it is moving.
(c) Yes, an electric field can exert a force on a moving charged object. A moving charged object will experience a force perpendicular to its velocity and the electric field direction, known as the Lorentz force.
(d) Yes, a magnetic field can exert a force on a moving charged object. A moving charged object in a magnetic field will experience a force perpendicular to both its velocity and the magnetic field direction, also known as the Lorentz force.
(e) Yes, an electric field can exert a force on a straight current-carrying wire. The electric field exerts a force on the charges in the wire, causing them to move, which results in a net force on the wire.
(f) Yes, a magnetic field can exert a force on a straight current-carrying wire. The magnetic field exerts a force on the moving charges in the wire, resulting in a net force on the wire.
(g) Yes, an electric field can exert a force on a beam of moving electrons. The electric field exerts a force on the electrons, causing them to accelerate or decelerate depending on the direction of the field.
(h) Yes, a magnetic field can exert a force on a beam of moving electrons. The magnetic field exerts a force on the moving electrons, causing them to experience a deflecting force perpendicular to their velocity and the magnetic field direction.
To learn more about electric field refer to:
brainly.com/question/15800304
#SPJ4
We always see the same side of the Moon because a. the Moon does not rotate on its axis. b. the Moon rotates on its axis once for each revolution around Earth. c. when t…
We always see the same side of the Moon because
a. the Moon does not rotate on its axis.
b. the Moon rotates on its axis once for each revolution around Earth.
c. when the other side of the Moon is facing Earth, it is unlit.
d. when the other side of the Moon is facing Earth, it is on the opposite side of Earth.
e. none of the above
We always see the same side of the Moon because the "Moon rotates on its axis once for each revolution around Earth." Thus, the correct option will be B.
How does the Moon rotates?When the Moon rotates on its axis once for each revolution around Earth, then we always see the same side of the Moon. The reason behind this is that the moon's rotation takes almost the same time as it takes to orbit the Earth.
When the same side of the moon is facing the Earth, it appears to be unchanging. That is why we always see the same side of the moon from Earth. The other side of the Moon is known as the far side, which was first observed by the Soviet spacecraft Luna 3 in 1959.
Therefore, the correct option will be B.
Learn more about Moon here:
https://brainly.com/question/13538936
#SPJ11
Milk with a density of 970 kg/m ∧ 3 is transported on a level road in a 9−m long, 3−m diameter cylindrical tanker. The tanker is completely filled with milk, i.e., no air space in the tank. If the truck is accelerating from a stop signal at 7.0 m/s ∧ 2 to the left, determine the pressure difference between the maximum and minimum pressures in the tank. Depict on the figure the location of the minimum and maximum pressures in the tank.
ΔP = (970 kg/m^3)(7.0 m/s^2)(4.26 m) = 29,852 Pascal. Therefore, the pressure difference between the maximum and minimum pressures in the tank is 29,852 Pa. The minimum pressure occurs at the bottom of the tank, while the maximum pressure occurs at the top of the tank.
The pressure difference between the maximum and minimum pressures in the tank can be calculated using the equation for pressure:
P = ρgh
where P is the pressure, ρ is the density of the milk, g is the acceleration due to gravity, and h is the height of the liquid column. Since the tanker is cylindrical and completely filled with milk, the height of the liquid column can be determined using the formula for the volume of a cylinder:
V = πr^2h
where V is the volume of the milk, r is the radius of the tanker (which is half of the diameter), and h is the height of the milk column. Solving for h, we get:
h = V / (πr^2)
The volume of the milk can be determined using the formula for the volume of a cylinder:
V = πr^2h
where r is the radius of the tanker (which is half of the diameter), and h is the length of the tanker. Substituting the given values, we get:
V = π(3/2)^2(9) = 31.8 m^3
The height of the liquid column is:
h = V / (πr^2) = 31.8 / (π(3/2)^2) = 4.26 m
The pressure difference between the maximum and minimum pressures in the tank can be calculated using the formula:
ΔP = ρgh
where ΔP is the pressure difference, ρ is the density of the milk, g is the acceleration due to gravity, and h is the height of the liquid column. Substituting the given values, we get:
ΔP = (970 kg/m^3)(7.0 m/s^2)(4.26 m) = 29,852 Pa
Therefore, the pressure difference between the maximum and minimum pressures in the tank is 29,852 Pa. The minimum pressure occurs at the bottom of the tank, while the maximum pressure occurs at the top of the tank.
For more such questions on Pressure
https://brainly.com/question/20492463
#SPJ11
a student pulls a 1500 kg suitcase along a flat sidewalk. if the cord on the suitcase breaks when the force is greater than 50n, what is the maximum acceleration that the student can achieve with the suitcase?
The maximum acceleration that the student can achieve with the 1500 kg suitcase is 50N/1500kg = 0.033 m/s2.
Acceleration is the change in velocity per unit time. Acceleration is a vector quantity that has both magnitude and direction. Acceleration is divided into deceleration acceleration and acceleration acceleration. Acceleration decreases meaning the direction of acceleration is opposite to the direction of velocity.
To calculate the maximum acceleration, we can use the following equation:
Force = Mass x Acceleration. Therefore, 50N = 1500kg x Acceleration
Solving for Acceleration, we get 50N/1500kg = 0.033 m/s2.
Learn more about acceleration : brainly.com/question/20595261
#SPJ11
In the context of research evidence from the study conducted by Williams and McCririe, which of the following operates when a person picks up information critical to catching an object
both central and peripheral vision
In the context of research evidence from the study conducted by Williams and McCririe, both central and peripheral vision operate when a person picks up information critical to catching an object.
What is vision?
Vision is the sense that allows us to recognize and understand the physical world around us. Our brains then receive this information and convert it into the pictures that we see with our eyes.
Vision is the term used to describe the ability to see things with our eyes, such as color, form, and movement.
In the context of research evidence from the study conducted by Williams and McCririe, both central and peripheral vision operate when a person picks up information critical to catching an object.
Their research found that peripheral vision was essential to athletes performing in certain sports such as cricket, soccer, and baseball.
Peripheral vision, as well as central vision, are critical components of efficient eye tracking and hand-eye coordination.
Learn more about vision here:
https://brainly.com/question/4269555
#SPJ11
why is a polarized filter helpful to a photographer? A. it transmits all light
Answer:
It blocks some light, but not all.
Explanation:
The point of polarization is to get the light to travel in a single plane. The light waves occur in a single plane. The direction of the vibration of the waves is the same. With two polarized filters, it is possible to block out nearly all the light.
suppose your planet at 1 meter from the basketball represents a distance of 4 x 107 km (-0.3 al) from the star. the next closest star to the sun is 4 x 1013 km away. how far away from the model star/planet would you have to be for the distances in the system to be to scale? express your answer in meters and kilometers.
Answer: The model star/planet would have to be 1,000 km away from the next closest star.
Explanation:
We need to find out the distance required for the distances in the system to be in scale.
Let's use the proportion to solve the problem:
1 m/4 × 10⁷ km = x/4 × 10¹³ km
Where x is the distance required for the distances in the system to be in scale.
Cross-multiply: 4 × 10¹³ km × 1 m = 4 × 10⁷ km × x
Simplify: 4 × 10¹³ m = 4 × 10⁷ x
Divide both sides by 4 × 10⁷ :1 × 10⁶ = x
Therefore, the distance required for the distances in the system to be in scale is 1 × 10⁶ m or 1,000 km.
So the model star/planet would have to be 1,000 km away from the next closest star.
Learn more about distance here
https://brainly.com/question/26550516
#SPJ11
a satellite is in a circular orbit around an unknown planet. the satellite has a speed of 1.89 x 104 m/s, and the radius of the orbit is 2.76 x 106 m. a second satellite also has a circular orbit around this same planet. the orbit of this second satellite has a radius of 6.98 x 106 m. what is the orbital speed of the second satellite?
The orbital speed of the second satellite is 6.55 × 10³ m/s.
The formula used to find the orbital speed of a satellite is given as v=√(GM/r).
Therefore, the value of the first satellite's speed is given as v₁=1.89×104 m/s, and the radius is r₁=2.76×106 m. Using the above formula, the mass of the planet is given as:
M= v²r/G= (1.89×104 m/s)² (2.76×106 m)/(6.6743 × 10⁻¹¹ Nm²/kg²) = 5.31 × 10²⁴ kg.
Now, the orbital speed of the second satellite, given as v₂, is equal to:
v₂ = √(GM/r₂); where G = gravitational constant = 6.6743 × 10⁻¹¹ Nm²/kg²;
M = mass of the planet = 5.31 × 10²⁴ kg;
r₂ = radius of orbit of the second satellite = 6.98 × 10⁶ m.
Substituting the values given above, we get:
v₂ = √(GM/r₂)= √[(6.6743 × 10⁻¹¹ Nm²/kg²) × (5.31 × 10²⁴ kg) / (6.98 × 10⁶ m)] = 6.55 × 10³ m/s
To know more about "orbital speed" refer here:
https://brainly.com/question/541239#
#SPJ11
The electric flux through a spherical surface is4.3×104 N⋅m2/C. What is the net charge enclosed by the surface? The net charge enclosed by the surface isμC. The electric flux through a cubical box34 cmon a side is7.5×103 N⋅m2/C. What is the total charge enclosed by the box? The total charge enclosed by the box isμC
For the electric flux through a spherical surface is 4.3 x 10⁴ N⋅m²/C, then the net charge enclosed by the surface is μC, and for the electric flux through a cubical box 34 cm on a side is 7.5 x 10³ N⋅m²/C, the total charge enclosed by the box is μC.
The electric flux through a spherical surface is 4.3 x 10⁴ N⋅m²/C.
The net charge is Electric Flux = Charge / Surface Area,
so the net charge enclosed is 4.3 x 10⁴ / (4πr²) where r is the radius of the sphere.
Therefore, the net charge enclosed by the surface is μC.
The electric flux through a cubical box 34 cm on a side is 7.5 x 10³ N⋅m²/C.
The total charge is Electric Flux = Charge / Surface Area,
so the total charge enclosed is 7.5 x 10³ / (6a²)
where a is the length of one side of the cube.
Therefore, the total charge enclosed by the box is μC.
Learn more about electric flux here:
https://brainly.com/question/2664005
#SPJ11
A battery-powered toy car pushes a stuffed rabbit across the floor.Part ADraw a free-body diagram for a car (assume that it is moving from left to the right).Draw the force vectors with their tails at the dot. The orientation of your vectors will be graded. The exact length of your vectors will not be graded but the relative length of one to the other will be graded.Part BDraw a free-body diagram for a rabbit.Draw the force vectors with their tails at the dot. The orientation of your vectors will be graded. The exact length of your vectors will not be graded but the relative length of one to the other will be graded.
Part A: Thrust acts on the right in the direction of motion. Gravity acts downward.
Part B: The direction of air resistance is opposite to the direction of motion, which is shown towards the left. Gravity acts downwards.
Part A:
A free-body diagram for a car is as follows:
The direction of friction is opposite to the direction of motion, which is shown towards the left.
The diagram shows three forces acting on the toy car that is battery-powered, which is as follows:
The force due to friction is labeled as [tex]f_K[/tex].
The force of thrust is labeled as [tex]f_T[/tex]. The force of gravity is labeled as [tex]f_g[/tex].
Part B:
A free-body diagram for a rabbit is as follows:
The diagram shows three forces acting on the stuffed rabbit that is being pushed by a toy car that is battery-powered, which is as follows:
The direction of friction is opposite to the direction of motion, which is shown towards the right.
The force due to friction is labeled as [tex]f_K[/tex]. The force due to air resistance is labeled as fair. The force of gravity is labeled as [tex]f_g[/tex].
For similar question on Gravity
https://brainly.com/question/557206
#SPJ11
When using compass orientation, migrating animals make use of _____.a. memories from previous trips with parentsb. familiar landmarks and olfactory cuesc. the north and south polesd. the sun, stars, and Earth's magnetic field
When using compass orientation, migrating animals make use of the sun, stars, and Earth's magnetic field to navigate. So, option d is correct option.
Compass orientation in migrating animals is the process of using the sun, stars, and Earth's magnetic field to navigate. Migrating animals use a variety of techniques to navigate, depending on their species and environment.
Some animals use the position of the sun, stars, and Earth's magnetic field as their primary means of orientation when migrating. This is known as compass orientation.
Compass orientation is a technique that relies on environmental cues, such as the position of the sun and stars, to determine direction. Some animals can use the Earth's magnetic field to navigate as well. This is known as magnetic orientation.
Magnetic orientation is used by some species of birds and fish, as well as certain insects and reptiles. Other animals use landmarks and olfactory cues to navigate.
These animals rely on visual or chemical markers in the environment to orient themselves. This technique is known as piloting. Piloting is used by animals such as rodents, bats, and some species of birds. Animals that use piloting must be able to remember and recognize the landmarks they use as cues to navigate.
Finally, some animals use memories from previous trips with parents to navigate. This technique is known as true navigation. True navigation requires animals to have a highly developed sense of spatial awareness and memory. True navigation is used by animals such as sea turtles and some species of birds.
All of these techniques require different cognitive abilities and sensory mechanisms, but they allow animals to navigate over long distances to reach their desired destinations.
for similar question on magnetic field to navigate.
https://brainly.com/question/22986969
#SPJ11
in one cycle a heat engine absorbs 480 j from a high-temperature reservoir and expels 320 j to a low-temperature reservoir. if the efficiency of this engine is 56% of the efficiency of a carnot engine, what is the ratio of the low temperature to the high temperature in the carnot engine?
The ratio of the low temperature to high temperature of the Carnot engine is 2.38.
What is the efficiency of Carnot engine?The efficiency of the Carnot engine can be defined as the ratio of network done per cycle by the engine to the heat energy absorbed by the engine per cycle by the working substance from the source.
Efficiency = 1 - (Tlow/Thigh)
Heat absorbed by engine = 480J
Heat expelled by engine = 320J
Efficiency of the engine = 56% of efficiency of Carnot engine
The ratio of low temperature to high temperature in the Carnot engine.
Let's assume the efficiency of the Carnot engine is 'ηc' = 1 - T₂/T₁
Where, T₂ = Low temperature and T₁ = High temperature
To calculate the efficiency of the engine given, η = (Q1 - Q2)/Q1
η = (480 - 320)/480
η = 160/480
η = 1/3
η = 33.33%
Now, η = 56% × ηc
0.56ηc = 1/3ηc = (1/3)/0.56 = 0.58
As we already know, ηc = 1 - T₂/T₁
T₂/T₁ = 1 - ηc
T₂/T₁ = 1 - 0.58
T₂/T₁ = 0.42
T₁/T₂ = 1/0.42
T₁/T₂ = 2.38
Therefore, the ratio of low temperature to high temperature in the given Carnot engine with an efficiency of 56% will be about 2.38.
Learn more about Carnot engine here:
https://brainly.com/question/14680478
#SPJ11
a waterbed heater uses 450 w of power. it is on 35 % of the time, off 65 % . part a what is the annual cost of electricity at a billing rate of $0.13 per kwhr ? express your answer using two significant figures.
The annual cost of electricity at a billing rate of $0.13 per kWhr for a waterbed heater that uses 450 W of power is $36.51.
What is the usage of the waterbed heater in a day?For the calculation of the energy consumed, one must know the energy consumed by the heater per day. The energy consumed in one day can be calculated by multiplying the power consumed by the hours the heater is used. The power consumed by the heater is 450 W.
The heater is used 35% of the time and is off 65% of the time. The percentage of time the heater is used is calculated using the formula:
Percentage of time the heater is used = (Time heater is on/Total time) × 100
Percentage of time the heater is used = (35/100) × 100
Percentage of time the heater is used = 35%
The percentage of time the heater is off is calculated using the formula:
Percentage of time the heater is off = (Time heater is off/Total time) × 100
Percentage of time the heater is off = (65/100) × 100
Percentage of time the heater is off = 65%
Thus, the heater is used for 8.4 hours per day (i.e., 24 hours × 35%) and is off for 15.6 hours per day (i.e., 24 hours × 65%).
The energy consumed per day can be calculated by multiplying the power consumed by the time the heater is on. Energy consumed per day = Power consumed × Time heater is on
Energy consumed per day = 450 W × 8.4 hours
Energy consumed per day = 3780 Wh
Energy consumed per day = 3.78 kWh
The annual cost of electricity can be calculated by multiplying the energy consumed per year by the cost of electricity per kWh.
Annual cost of electricity = Energy consumed per year × Cost of electricity per kWh
Annual cost of electricity = 3.78 kWh × $0.13/kWh
Annual cost of electricity = $0.4914/day
Annual cost of electricity = $179.31/year
Hence, the annual cost of electricity at a billing rate of $0.13 per kWhr for a waterbed heater that uses 450 W of power is $36.51.
Learn more about Power here:
https://brainly.com/question/27442707
#SPJ11
Water is flowing in a circular pipe varying cross-sectional area, and at all points, the water completely fills the pipe.a) At one point in the pipe the radius is 0.150 m. What is the speed of the water at this point if the water is flowing into this pipe at a steady rate of 1.20 m3/s?b) At a second point in the pipe the water speed is 2.90 m/s. What is the radius of the pipe at this point?
The speed of water at the point with a radius of 0.150 m is 16.97 m/s while the radius of the pipe at the point where the water speed is 2.90 m/s is 0.0682 m.
a) To find the speed of the water at a point of a circular pipe where the radius is 0.150 m if the water is flowing into this pipe at a steady rate of 1.20 m³/s, we'll use the equation;
Q = A₁V₁ = A₂V₂ Where Q = Flow rate (m³/s)A₁ = Cross-sectional area at one point (m²)V₁ = Velocity of water at one point (m/s)A₂ = Cross-sectional area at a second point (m²)V₂ = Velocity of water at the second point (m/s)At one point in the pipe, the radius is 0.150 m.Therefore, the cross-sectional area, A₁ is given by:
A₁ = πr₁² = π (0.150 m)² = 0.0707 m²Given that the water is flowing into the pipe at a steady rate of 1.20 m³/s, we can write;Q = A₁V₁1.20 m³/s = 0.0707 m² V₁V₁ = 1.20/0.0707V₁ = 16.97 m/s.Therefore, the speed of water at the point with a radius of 0.150 m is 16.97 m/s.
b) To find the radius of the pipe at a point where the water speed is 2.90 m/s, we'll use the same equation as in part (a);Q = A₁V₁ = A₂V₂At a second point in the pipe, the water speed is 2.90 m/s.Given that the water completely fills the pipe, we know that the volume flow rate, Q will remain constant at 1.20 m³/s.So, we have:
Q = A₁V₁ = A₂V₂We know that A₁ = πr₁²So, Q = πr₁²V₁Also, we know that A₂ = πr₂²So, Q = πr₂²V₂Since the volume flow rate is constant, we can equate both equations,πr₁²V₁ = πr₂²V₂Dividing both sides of the equation by π, we have;r₁²V₁ = r₂²V₂But we are interested in finding the radius of the pipe at the second point, r₂.So, we can express r₁ in terms of r₂ using the relationship between the cross-sectional areas;
A₁ = A₂r₁² = (A₂/A₁)²r₂²r₁ = r₂ (A₂/A₁)^(1/2).We know that A₁ = πr₁²We can find A₂ using the fact that the water completely fills the pipe;
A₁V₁ = A₂V₂πr₁²V₁ = A₂V₂π(0.150 m)²(16.97 m/s) = A₂(2.90 m/s)A₂ = π(0.150 m)²(16.97 m/s)/(2.90 m/s)A₂ = 0.0707 m²
So,r₂ = r₁(A₂/A₁)^(1/2)r₂ = 0.150 m × (0.0707 m²/π)/(0.0150 m²)^(1/2)r₂ = 0.0682 m. Therefore, the radius of the pipe at the point where the water speed is 2.90 m/s is 0.0682 m.
More on velocity: https://brainly.com/question/6293650
#SPJ11
A straight 2.40 m wire carries a typical household current of 1.50 A (in one direction) at a location where the earth's magnetic field is 0.550 gauss from south to north. *I know there's a lot of questions, but I will rate the you-know-what out of you a) Find the direction of the force that our planet's magnetic field exerts on this cord if is oriented so that the current in it is running from west to east. b) Find the magnitude of the force that our planet's magnetic field exerts on this cord if is oriented so that the current in it is running from west to east. c) Find the direction of the force that our planet's magnetic field exerts on this cord if is oriented so that the current in it is running vertically upward. d) Find the magnitude of the force that our planet's magnetic field exerts on this cord if is oriented so that the current in it is running vertically upward. e) Find the direction of the force that our planet's magnetic field exerts on this cord if is oriented so that the current in it is running from north to south. f) Find the magnitude of the force that our planet's magnetic field exerts on this cord if is oriented so that the current in it is running from north to south. g) Is the magnetic force ever large enough to cause significant effects under normal household conditions?
a) If the current is running from west to east, the force that our planet's magnetic field exerts on this cord is directed upwards
b) The magnitude of the force that our planet's magnetic field exerts on this cord if it is oriented so that the current in it is running from west to east is F =2.64 x 10^-4 N
c) If the current is running vertically upward, the force that our planet's magnetic field exerts on this cord is directed to the left. west
d) The magnitude of the force that our planet's magnetic field exerts on this cord if it is oriented so that the current in it is running vertically upward is F = 0 zero
e) If the current is running from north to south, the force that our planet's magnetic field exerts on this cord is directed east.
f) The magnitude of the force that our planet's magnetic field exerts on this cord if it is oriented so that the current in it is running from north to south is F = 2.64 x 10^-4 N
g) The magnetic force is not large enough to cause significant effects under normal household conditions.
EXPLANATION
a) The direction of the force that our planet's magnetic field exerts on the cord is perpendicular to both the direction of the current and the direction of the magnetic field, according to the right-hand rule. In this case, if the current is running from west to east, and the magnetic field is from south to north, the force will be directed upwards.
b) The magnitude of the force can be calculated using the formula:
F = BIL sin(theta)
where B is the magnitude of the magnetic field, I is the current, L is the length of the wire, and theta is the angle between the direction of the current and the direction of the magnetic field. In this case, theta is 90 degrees, so sin(theta) = 1. Substituting the given values, we get:
F = (0.550 x 10^-4 T) x (1.50 A) x (2.40 m) x 1
= 2.64 x 10^-4 N
Therefore, the magnitude of the force is 2.64 x 10^-4 N.
c) If the current in the wire is running vertically upward, the force will be directed towards the west.
d) Using the same formula as in part (b), we can calculate the magnitude of the force:
F = (0.550 x 10^-4 T) x (1.50 A) x (2.40 m) x sin(90)
= 0
Therefore, the magnitude of the force is zero.
e) If the current in the wire is running from north to south, the force will be directed towards the east.
f) Using the same formula as in part (b), we can calculate the magnitude of the force:
F = (0.550 x 10^-4 T) x (1.50 A) x (2.40 m) x 1
= 2.64 x 10^-4 N
Therefore, the magnitude of the force is 2.64 x 10^-4 N.
g) The magnitude of the magnetic force in this case is quite small, and under normal household conditions, it is unlikely to cause significant effects. However, in some situations, such as in electrical power transmission systems, the effects of the magnetic force may need to be taken into account.
For more such questions on magnetic field
https://brainly.com/question/13689629
#SPJ11
Two very long parallel wires are a distance d apart and carry equal currents in opposite directions. The locations where the net magnetic field due to these currents is equal to double the magnetic field of one wire are found A. midway between the wires. B. The net field is not zero any where. C. a distanced/√2 to the left of the left wire and also a distance d/√2 to to the right of the right wire. a distance d /2 to the left of the left wire and also a distance d/2 to the right of the right wire. D. a distance d to the left of the left wire and also a distance d to the right of the right wire.
A distance d/√2 to the left of the left wire and also a distance d/√2 to the right of the right wire. The correct option is C.
How to calculate the distance of the magnetic field?Let's consider a point P at a distance d/√2 to the left of the left wire. At this point, the magnetic field due to the left wire is:
B₁= μ₀I/(2π(d/√2))
Similarly, the magnetic field due to the right wire at point P is:
B₂ = μ₀I/(2π((d/√2)+d))
The net magnetic field at point P is:
Bnet = B₂ - B₁ = μ₀I/(2π((d/√2)+d)) - ₀/(2π(d/√2))
Simplifying this expression, we get:
Bnet = μ₀I/(2πd)
This is equal to the magnetic field due to one wire at a distance d from the wire. Therefore, the net magnetic field is double the magnetic field of one wire at a distance d/√2 to the left of the left wire and also a distance d/√2 to the right of the right wire. Option C is correct.
To learn more about magnetic fields follow
https://brainly.com/question/12981734
#SPJ11
Q4. Convert these into proper vector notation:
Westward velocity of 42 km/h.
Position 6. 5 measured in m that is North of the reference point.
Downward acceleration measured in m/s2 that has a magnitude of 1. 9.
42 km/h westward velocity can be expressed as: v is equal to (-42 km/h) * (1000 m/km) / (3600 s/h) * I . Therefore, the proper vector notation for the downward acceleration of magnitude 1.9 m/s^2 is -1.9 m/s^2 in the downward direction (k).
where the unit vector pointing west is called i. If we condense this expression, we get: v = -11.67 m/s * I Hence, -11.67 m/s in the westward direction is the correct vector notation for the 42 km/h westward velocity (i). North of the reference point, position 6.5 measured in metres, can be expressed as: r = 6.5 m * j where j represents the unit vector pointing north. Hence, 6.5 m in the northward direction is the correct vector notation for the location 6.5 m north of the reference point (j). It is possible to express a downward acceleration with a magnitude of 1.9 in m/s2 as follows: a = -1.9m/s^2 * k where k is the unit vector in the downward direction. Therefore, the proper vector notation for the downward acceleration of magnitude 1.9 m/s^2 is -1.9 m/s^2 in the downward direction (k).
learn more about vector notation here:
https://brainly.com/question/17264346
#SPJ4
A student must analyze data collected from an experiment in which a block of mass 2M traveling with a speed vo collides with a block of mass M that is initially at rest. After the collision, the two blocks stick together. Which of the following applications of the equation for the conservation of momentum represent the initial and final momentum of the system for a completely inelastic collision between the blocks? Justify your selection. Select two answers. A. 2Mo = 3Muf, because the blocks stick together after the collision.
B. 3Mvo = 3MUf, because the blocks stick together after the collision. C. 2MVo = 2MU + Muf, because the blocks stick together after the collision. D. 2MVo = M0o + 3 Muf, because the blocks do not stick together after the collision.
A student must analyze data collected from an experiment in which a block of mass 2M traveling with a speed vo collides with a block of mass M that is initially at rest. After the collision, the two blocks stick together. Thus, the correct options are A and B.
What is Momentum?The initial momentum of the system = the momentum of block 1 = (2M)vo. The final momentum of the system = the momentum of the combined blocks = (2M + M)uf = 3Muf. Therefore, the correct applications of the equation for the conservation of momentum that represent the initial and final momentum of the system for a completely inelastic collision between the blocks are:
2Mo = 3Muf, because the blocks stick together after the collision. 3Mvo = 3MUf, because the blocks stick together after the collision.
Therefore, the correct options are A and B.
Learn more about Momentum here:
https://brainly.com/question/30677308
#SPJ11
what is the minimum angular velocity (in rpm ) for swinging a bucket of water in a vertical circle without spilling any? the distance from the handle to the bottom of the bucket is 35 cm . express your answer in revolutions per minute.
The minimum angular velocity (in rpm) for swinging a bucket of water in a vertical circle without spilling any is 5.56 rpm.
The minimum angular velocity (in rpm) for swinging a bucket of water in a vertical circle without spilling any is given by the formula; Vmin=√g/R
where:
Vmin = minimum angular velocity (in rpm)g = acceleration due to gravity (9.81 m/s²)R = radius of the circular path or distance from the handle to the bottom of the bucket (35 cm)To express the answer in revolutions per minute, the radius of the circle must be converted to meters;R = 35 cm = 0.35 m
Substituting the values given above into the formula;
Vmin=√g/R Vmin=√9.81/0.35 Vmin = 5.56 rpmTherefore, the minimum angular velocity (in rpm) for swinging a bucket of water in a vertical circle without spilling any is 5.56 rpm.
Learn more about velocity: https://brainly.com/question/25749514
#SPJ11
what happens after the helium flash in the core of a star?
After the helium flash in a star, the core quickly heats up and expands.
A helium flash is the very brief thermal runaway nuclear fusion of significant amounts of helium into carbon during the red giant phase of low mass stars (between 0.8 solar masses (M) and 2.0 M). The centre expands as a result of the core becoming warmer as a result of this.
Following the onset of helium nuclear reactions in a star's core, helium nuclei fuse to create carbon and oxygen.
Most of the time, the stars' positions in reference to one another remain constant. Convergence between Orion and Taurus is ongoing. Ursa Minor is never far from Draco. The stars appear to us as an endless backdrop painting in the sky that hardly moves in reference to one another.
To know more about stars:
https://brainly.com/question/29572549
#SPJ4
Help asaaap it's about doppler effect
The frequency that the bad guy hear is 12000 hz when the police car is moving with speed of 80m/s.
Frequencyfo=fs(vvov), where fo is the observed frequency, fs is the source frequency, v is the speed of sound, vo is the observer's speed, the top sign indicates the observer is approaching the source, and the bottom sign indicates the observer is leaving the source.Equation fo=800(80-65) fo = 12000 after substituting the variablesThe apparent change in frequency of a wave as a result of an observer moving with respect to the wave source is known as the Doppler effect or Doppler shift. It bears the name of the Austrian physicist Christian Doppler, who first described the phenomenon in 1842.For more information on doppler effect kindly visit to
https://brainly.com/question/15318474
#SPJ1
The half life of a radioactive substance is 5 hours. If 5g of the substance is left after 20 hours, determine the original mass of the substance
Answer:
The original mass of the substance was 10g.
Explanation:
The half-life of a radioactive substance is the amount of time it takes for half of the substance to decay. In this case, the half-life is 5 hours.
We can use the half-life formula to find the original mass of the substance:
N = N0 * (1/2)^(t/T)
where:
---N0 is the initial mass of the substance
---N is the remaining mass of the substance after time t
---T is the half-life of the substance
We know that after 20 hours, only half of the substance remains:
N = N0 * (1/2)^(20/5) = 0.5 * N0
If we solve for N0, we get:
N0 = N / 0.5 = 5g / 0.5 = 10g
Therefore, the original mass of the substance was 10g.
A particle in an infinite square well potential has an initial wave function psi (x, t = 0) = Ax (L - x). Find the time evolution of the state vector. Find the expectation value of the position as a function of time.
The position expectation value as a function of time is constant and is equal to L/3.
Given a particle in an infinite square well potential has an initial wave function Ψ (x, t = 0) = Ax (L - x).The time evolution of the state vector: The time evolution of the state vector is given by Ψ(x,t) = ΣC_nΨ_n (x) e^(-iE_n t/h).The expectation value of the position as a function of time:The expectation value of the position as a function of time is given by the formula given below:x = Σa_n^2x_nΨ_n(x)Ψ_n*(x). Where,
a_n is the coefficient for each energy level.
Energy levels for infinite square well potential is given byE_n = n^2h^2 / 8mL^2Now, let us find the value of coefficient A. We know that a particle in a square well is normalized using the following formula:
∫Ψ^2 dx = 1. 0 to L∫Ax(L-x)^2dx = 1A(L^3)/3 = 1, A = √(3/L^3).
Now, the wavefunction for the particle is given by:
Ψ (x, t = 0)
= Ax (L - x)
= √(3/L^3) x (L - x).
Now, we can express this wave function in terms of the energy eigenfunctions as below:
Ψ (x, t = 0)
= Σ a_nΨ_n (x)
= Σa_n sin((nΠx)/L).
We can calculate the value of coefficient a_n by integrating the product of the initial wavefunction with the energy eigenfunctions, which is given by: a_n = 2/L ∫Ψ(x, t = 0) sin((nΠx)/L) dx.
Now, let us calculate the value of coefficient
a_n.a_n = 2/L ∫Ψ(x, t = 0) sin((nΠx)/L) dxa_n
= 2/L ∫√(3/L^3) x (L - x)sin((nΠx)/L) dxa_n = 2√3/L^2 ∫x(L - x)sin((nΠx)/L) dx.
From the previous results of integration,
a_n = (-1)^n+1 24√3/nΠ^3
a_n = (-1)^n+1 24√3/nΠ^3
Ψ(x,t) = ∑ a_nΨ_n(x) exp(-iE_n t/ℏ). Where E_n = n²h²π² / 2mL².
Substituting the values of a_n in the above formula, Ψ(x,t) = Σ(-1)^n+1 24√3/nΠ^3 sin(nΠx/L) exp(-in²π²h²t/2mL²ℏ²). Expectation value of the position as a function of time: The expectation value of the position is given by the formula, x = Σa_n²x_n. Where x_n is the position of nth energy level.
So, x_n = L/nSo,x = L∑a_n²/n From the previous results of coefficient, Σa_n²/n = 1/3. Now, x = L/3. Hence the position expectation value as a function of time is constant and is equal to L/3.
Learn more about expected value: brainly.com/question/24305645
#SPJ11
Select the correct location on the image.
The image shows the visible light spectrum received from a star. Which three parts of the spectrum show the presence of elements in the star’s atmosphere?
The visible light spectrum is the range of wavelengths the human eye can detect, ranging from 380 to 700 nanometers.
What are visible light examples?People think of the sun, light bulbs, candles, and flames when they think of light, but visible light originates from many sources and in many hues. Other visible light sources include television and computer displays, glow sticks, and pyrotechnics.
This is why this area of the electromagnetic spectrum is known as the visible spectrum or colour spectrum. It primarily comprises of seven colours: violet, blue, green, yellow, orange, and red.
Learn more about visible light spectrum
brainly.com/question/18704022
#SPJ1
Answer:
It is the three spots where there are lines. Between 400 and 500(the two lines), between 600 and 700(the two lines), and the one line between 700 and 800.
Which of the following correctly compares the Sun's energy generation process to the energy generation process in human-built nuclear power plants?
Both processes involve nuclear fusion, but the Sun fuses hydrogen while nuclear power plants fuse uranium.
The Sun generates energy by fusing small nuclei into larger ones, while our power plants generate energy by the fission (splitting) of large nuclei.
The Sun generates energy through nuclear reactions while nuclear power plants generate energy through chemical reactions.
The Sun generates energy through fission while nuclear power plants generate energy through fusion.
The correct comparison of the energy generation processes is "The Sun generates energy by fusing small nuclei into larger ones, while our power plants generate energy by the fission (splitting) of large nuclei". Thus, the correct options are A and B.
What is Nuclear power?Nuclear reactions involve the alteration of an atom's nucleus in both cases. Nuclear power plants and the sun both use energy generated by these nuclear reactions to produce electricity. The difference is in the type of nuclear reaction that takes place.
In the Sun, nuclear fusion is the process by which atomic nuclei of low atomic number fuse to form a heavier nucleus with the release of energy. The energy produced in this way is what makes the Sun so hot and bright. In a nuclear power plant, nuclear fission is the process by which the nucleus of an atom is split into two smaller nuclei.
The energy that is released in the process is used to heat water, creating steam that drives a turbine, which in turn drives a generator to produce electricity.
Therefore, the correct options are A and B.
Learn more about Nuclear power here:
https://brainly.com/question/18769119
#SPJ11
A student walks 1.0 kilometer due east and 1.0 kilometer due south. Then
she runs 2.0 kilometers due west. The magnitude of the student's
resultant displacement is closestto
A. 3.4 km
B. 1.4 km
C. 4.0 km
D. O km
The resulting displacement will be 3.4 km. The correct option is A.
The displacement is calculated by finding the displacement from east to west, which is 2.0 km, and subtracting the displacement from north to south, which is 1.0 km.
A student walks 1.0 kilometers due east and 1.0 kilometers due south. Then she runs 2.0 kilometers due west. The magnitude of the student's resultant displacement is closest to 3.4 km.
To begin with, we may use the Pythagorean Theorem to determine the resultant displacement's magnitude. The Pythagorean Theorem is a formula that is used to determine the length of a right triangle's sides when one is missing. This theorem is used to calculate the magnitude of the resultant displacement, which is a quantity. It's a good idea to draw a diagram to help you understand the problem.
Here's a rough sketch of the scenario: We will now apply the Pythagorean theorem in this way: The resultant displacement's magnitude is 3.4 kilometers. Thus, the correct option is A.
To know more about displacement follow
https://brainly.com/question/14637077
#SPJ11
write an expression for the magnitude of the force, f, exerted on the firefighter by the pole. answer in terms of the variables from the problem statement as well as g for the acceleration due to gravity.
The expression for the magnitude of the force exerted on the firefighter by the pole can be expressed as F = mg + ma.
Where m is the mass of the firefighter,
g is the acceleration due to gravity, and
a is the acceleration of the pole
In order to find an expression for the magnitude of the force, F, exerted on the firefighter by the pole, we need to consider the forces acting on the firefighter.
According to Newton's second law of motion, the force acting on an object is equal to its mass multiplied by its acceleration. In this case, the forces acting on the firefighter are the gravitational force, which is pulling the firefighter downwards with a force of mg, and the force exerted on the firefighter by the pole, which is pushing the firefighter upwards with a force of ma. Therefore, the total force acting on the firefighter is given by the sum of these two forces, which is: F = mg + ma
Thus, this expression gives us the magnitude of the force exerted on the firefighter by the pole. Here, m is the mass of the firefighter, g is the acceleration due to gravity, and a is the acceleration of the pole. if the pole is not accelerating (i.e., if a = 0), then the expression reduces to F = mg, which is the gravitational force acting on the firefighter.
To know more about Magnitude please visit :
https://brainly.com/question/30337362
#SPJ11
