Answer:
i did not known answer but anobody help you
Steam enters an adiabatic turbine at 6 MPa, 600°C, and 80 m/s and leaves at 50 kPa, 100°C, and 140 m/s. If the power output of the turbine is 5 MW, determine (a) the reversible power output and (b) the second-law efficiency of the turbine. Assume the surroundings to be at 25°C.
Answer:
(a) the reversible power output of turbine is 5810 kw
(b) The second-law efficiency of he turbine = 86.05%
Explanation:
In state 1: the steam has a pressure of 6 MPa and 600°C. Obtain the enthalpy and entropy at this state.
h1 = 3658 kJ/kg s1=7.167 kJ/kgK
In state 2: the steam has a pressure of 50 kPa and 100°C. Obtain the enthalpy and entropy at this state
h2 = 2682kl/kg S2= 7.694 kJ/kg
Assuming that the energy balance equation given
Wout=m [h1-h2+(v1²-v2²) /2]
Let
W =5 MW
V1= 80 m/s V2= 140 m/s
h1 = 3658kJ/kg h2 = 2682 kJ/kg
∴5 MW x1000 kW/ 1 MW =m [(3658-2682)+ ((80m/s)²-(140m/s)²)/2](1N /1kg m/ s²) *(1KJ/1000 Nm)
m = 5.158kg/s
Consider the energy balance equation given
Wrev,out =Wout-mT0(s1-s2)
Substitute Wout =5 MW m = 5.158kg/s 7
s1= 7.167 kJ/kg-K s2= 7.694kJ/kg-K and 25°C .
Wrev,out=(5 MW x 1000 kW /1 MW) -5.158x(273+25) Kx(7.167-7.694)
= 5810 kW
(a) Therefore, the reversible power output of turbine is 5810 kw.
The given values of quantities were substituted and the reversible power output are calculated.
(b) Calculating the second law efficiency of the turbine:
η=Wout/W rev,out
Let Wout = 5 MW and Wrev,out = 5810 kW
η=(5 MW x 1000 kW)/(1 MW *5810)
η= 86.05%
If you are driving down to the sleep downgrade and you have reached the speed of 40 mph , you would apply the setrvice break until your speed dropped to below_____mph.
Answer:
35 miles
Explanation:
When you are driving a truck that has an air brake system you have to keep in mind that when driving down a steep downgrade, the truck will automatically accelerate due to the inclination of the road, so in order to keep the speed to a controllable situation, you need to activate the service brake until you've reached the 35 miles per hour mark.
The temperature gradient in a spherical (or cylindrical) wall at steady state will always decrease (in magnitude) with increasing distance from the center (line), i.e. radial distance.
A. True
B. False
Answer:
True
Explanation:
Yes it is true that the Temperature gradient would also decrease with magnitude just as the distances rise from the centre line.
We have this cylinder equation as
[T1-T2 / ln(r1-r2)]2πKL
The radial distance is r2-r1
The gradient of temperature is T1-T2
From the equation,
The temperature gradient has a direct and proportional relationship to radial distance
T1-T2 ∝ ln(r2-r1)
1/T1-T2 = k(r2-r1)
This inverse relationship above confirms that the statement is true
In low speed subsonic wind tunnels, the value of test section velocity can be controlled by adjusting the pressure difference between the inlet and test-section for a fixed ratio of inlet-to-test section cross-sectional area.
a. True
b. false
Answer:
Hence the given statement is false.
Explanation:
For low-speed subsonic wind tunnels, the air density remains nearly constant decreasing the cross-section area cause the flow to extend velocity, and reduce pressure. Similarly increasing the world cause to decrease and therefore the pressure to extend.
The speed within the test section is decided by the planning of the tunnel.
Thus by adjusting the pressure difference won't change the worth of test section velocity.
Answer:
The given statement is false .
(50 POINTS) How many people use pipes in the world? How do you know this?
Answer:
7.9 billion people
Explanation:
If a heat engine has an efficiency of 30% and its power output is 600 W, what is the rate of heat input from the combustion phase
Answer:
The heat input from the combustion phase is 2000 watts.
Explanation:
The energy efficiency of the heat engine ([tex]\eta[/tex]), no unit, is defined by this formula:
[tex]\eta = \frac{\dot W}{\dot Q}[/tex] (1)
Where:
[tex]\dot Q[/tex] - Heat input, in watts.
[tex]\dot W[/tex] - Power output, in watts.
If we know that [tex]\dot W = 600\,W[/tex] and [tex]\eta = 0.3[/tex], then the heat input from the combustion phase is:
[tex]\eta = \frac{\dot W}{\dot Q}[/tex]
[tex]\dot Q = \frac{\dot W}{\eta}[/tex]
[tex]\dot Q = \frac{600\,W}{0.3}[/tex]
[tex]\dot Q = 2000\,W[/tex]
The heat input from the combustion phase is 2000 watts.
Your shifts productivity is Slow because one person is not pulling his share. The rest of the team is Getting upset.
Answer:
you are right but then you ddnt ask a question
An ideal neon sign transformer provides 9130 V at 51.0 mA with an input voltage of 240 V. Calculate the transformer's input power and current.
Answer:
Input power = 465.63 W
current = 1.94 A
Explanation:
we have the following data to answer this question
V = 9130
i = 0.051
the input power = VI
I = 51.0 mA = 0.051
= 9130 * 0.051
= 465.63 watts
the current = 465.63/240
= 1.94A
therefore the input power is 465.63 wwatts
while the current is 1.94A
the input power is the same thing as the output power.
) Please label the following statements as either True (T) or False (F). (a) In general, the greater the % of cold work, the smaller the recrystallization grain size. (b) The higher the annealing temperature, the smaller the recrystallization grain size. (c) The greater the % of cold work, the lower the recrystallization temperature.
Answer:
A. This option is true
B. This option is false
C. This option is true
Explanation:
A. Generally speaking, the greater percentage of cold, the recrystallization grain size would turn out to be smaller. Therefore this true.
B. A higher annealing temperature does not result in smaller recrystallization grain size. Therefore this is false.
C. As the percentage of cold work is greater, the recrystallization temperature would tend to be lower. Therefore this is true.
James the Pilot James is a pilot. He is wearing a flight suit. He flies to Paris. He loves flying. 1. James is a a) teacher b) doctor c) pilot. whatisthe 2. He is wearing a a) shirt b) t-shirt c) flight suit. 3. Where does he fly to? a) Italy b) Luxembourg c) Paris http https://whatistheurl.com Please visit our site for worksheets and charts
Answer:
1.c
2.c
3.c
Explanation:
James is a pilot, whistle. He is wearing a flight suit. Paris is the palace where does he fly to. Hence, option C, C, and C are correct.
What is the point of a flight suit?When flying an aircraft, such as a military aircraft, a glider, or a helicopter, one must wear a full-body suit called a flight suit. These outfits are typically meant to keep the user warm and are also functional (they have many of pockets) (including fire ). In most cases, it looks like a jumpsuit.
The G suit, sometimes known as a "anti-G suit," is a one-piece jumpsuit that shields a pilot from the pressure of G forces pressing down on him and causing discomfort or unconsciousness.
The traditional attire for pilots of military and commercial aircraft, helicopters, and even gliders is flight suits or flyers coveralls. In areas where there is a risk of fire, ground personnel—including aircrews—often wear flight suits as well.
Thus, option C, C, and C are correct.
For more information about point of a flight suit, click here:
https://brainly.com/question/12302183
#SPJ2
Identify the first step in preparing a spectrophotometer for use.
A. Make sure all samples and the blank are ready for measurement.
B. Prepare a calibration curve.
C. Measure the absorbance of the blank.
D. Turn on the light source and the spectrophotometer.
Answer:
D. Turn on the light source and the spectrophotometer.
Explanation:
A spectrophotometer is a machine used to measure the presence of any light-absorbing particle in a solution as well as its concentration. To prepare a spectrophotometer for use, the first step is to turn on the spectrophotometer and allow it to warm up for at least 15 minutes. After this is done, the next step will be to ensure that the samples and blank are ready. Next, an appropriate wavelength is set for the solute being determined. Finally, the absorbance is measured of both the blank and samples.
Problema:
Una nevera de vinos, con un peso bruto de 50 kg., que tiene las siguientes dimensiones: .60 m Largo x .49 m ancho x .50 m altura. Para ser transportadas en un contenedor de 40 pies D.V. responder las siguientes preguntas:
• 1.Cuántas neveras de vinos de acuerdo al volumen caben en un contenedor de 40 pies?
• De acuerdo dimensiones internas (largo, ancho y alto), ¿Cuántas caben en un contenedor de 40 pies?
• De acuerdo al peso que soporta el contenedor. ¿Cuántas neveras de vinos es posible transportar?
Answer:
I can't understand this language .
3-71A 20mm diameter steel bar is to be used as a torsion spring. If the torsional stress in the bar is not to exceed 110 MPa when one end is twisted through an angle of 15 degrees, what must be the length of the bar
Answer:
The right answer is "1.903 m".
Explanation:
Given that,
[tex]\tau =110 \ MPa[/tex]
[tex]G=80 \ GPa[/tex]
[tex]\Theta=15\times \frac{\pi}{180}[/tex]
[tex]=\frac{\pi}{12}[/tex]
[tex]d=20 \ mm[/tex]
As we know,
⇒ [tex]\frac{\tau}{r}=\frac{G \Theta}{L}[/tex]
Or,
⇒ [tex]L=\frac{G \theta r}{\tau}[/tex]
[tex]=\frac{80\times 10^3}{110}\times \frac{\pi}{12}\times 10[/tex]
[tex]=1903.9 \ mm[/tex]
or,
[tex]=1.903 \ m[/tex]
Set the leak rate to zero and choose a non-zero value for the proportional feedback gain.Restart the simulation and turn on the outflow valve.What happens to the liquid level in the tank?Repeat this process with higher and lower values for the proportional feedback gain.What happens when the proportional feedback gain is increased?What happens when it is decreased?Find the proportional gain that will reach steady state the quickest without oscillationin the state of the valve and restart the simulation.What is the system time constant, as determined from the tank level versus time plot.
Answer:
Explanation:
The proportional gain K is usually a fixed property of the controller . If proportional gain is increased , The sensitivity of the controller to error is increased but the stability is impaired. The system approaches the behaviour of on off controlled system and it response become oscillatory
Determine the pressure difference in N/m2,between two points 800m apart in horizontal pipe-line,150 mm diameter, discharging water at the rate of 12.5litres per second. Take the frictional coefficient ,f, as being 0.008
Answer: [tex]10.631\times 10^3\ N/m^2[/tex]
Explanation:
Given
Discharge is [tex]Q=12.5\ L[/tex]
Diameter of pipe [tex]d=150\ mm[/tex]
Distance between two ends of pipe [tex]L=800\ m[/tex]
friction factor [tex]f=0.008[/tex]
Average velocity is given by
[tex]\Rightarrow v_{avg}=\dfrac{12.5\times 10^{-3}}{\frac{\pi }{4}(0.15)^2}\\\\\Rightarrow v_{avg}=\dfrac{15.9134\times 10^{-3}}{2.25\times 10^{-2}}\\\\\Rightarrow v_{avg}=7.07\times 10^{-1}\\\Rightarrow v_{avg}=0.707\ m/s[/tex]
Pressure difference is given by
[tex]\Rightarrow \Delta P=f\ \dfrac{L}{d}\dfrac{\rho v_{avg}^2}{2}\\\\\Rightarrow \Delta P=0.008\times \dfrac{800}{0.15}\times \dfrac{997\times (0.707)^2}{2}\\\\\Rightarrow \Delta P=10,631.45\ N/m^2\\\Rightarrow \Delta P=10.631\ kPa[/tex]
Consider the equation y = 10^(4x). Which of the following statements is true?
A plot of log(y) vs. x would be linear with a slope of 4.
A plot of log(y) vs. log (x) would be linear with a slope of 10.
A plot of log(y) vs. x would be linear with a slope of 10.
A plot of y vs. log(x) would be linear with a slope of 4.
A plot of log(y) vs. log (x) would be linear with a slope of 4.
A plot of y vs. log(x) would be linear with a slope of 10.
Answer: Plot of [tex]\log y[/tex] vs [tex]x[/tex] would be linear with a slope of 4.
Explanation:
Given
Equation is [tex]y=10^{4x}[/tex]
Taking log both sides
[tex]\Rightarrow \log y=4x\log (10)\\\Rightarrow \log y=4x[/tex]
It resembles with linear equation [tex]y=mx+c[/tex]
Here, slope of [tex]\log y[/tex] vs [tex]x[/tex] is 4.
The following is a correlation for the average Nusselt number for natural convection over spherical surface. As can be seen in the above, the Nusselt number approaches 2 as Rayleigh number approaches zero. Prove that this situation corresponds to conduction heat transfer and in conduction heat transfer over sphere, the Nusselt number becomes 2. Hint: First step: Write an expression for heat transfer between two spherical shells that share the same center. Second step: Assume the outer spherical shell is infinitely large.
Answer:
Explanation:
[tex]r_2=[/tex]∞
[tex]q=4\pi kT_1(T_2-T_1)\\[/tex]
[tex]q=2\pi kD.[/tex]ΔT--------(1)
[tex]q=hA[/tex] ΔT[tex]=4\pi r_1^2(T_2_s-T_1_s)\\[/tex]
[tex]N_u=\frac{hD}{k} = 2+\frac{0.589 R_a^\frac{1}{4} }{[1+(\frac{0.046}{p_r}\frac{9}{16} )^\frac{4}{9} } ------(3)[/tex]
By equation (1) and (2)
[tex]2\pi kD.[/tex]ΔT=h.4[tex]\pi r_1^2[/tex]ΔT
[tex]2kD=hD^2\\\frac{hD}{k} =2\\N_u=\frac{hD}{k}=2\\[/tex]-------(4)
From equation (3) and (4)
So for sphere [tex]R_a[/tex]→0
The heat transfer surface area of a fin is equal to the sum of all surfaces of the fin exposed to the surrounding medium, including the surface area of the fin tip. Under what conditions can we neglect heat transfer from the fin tip?
Answer:
The explanation according to the given query is summarized in the explanation segment below.
Explanation:
If somehow the fin has become too lengthy, this same fin tip temperature approaches the temperature gradient and maybe we'll ignore heat transmission out from end tips.Additionally, effective heat transmission as well from the tip could be ignored unless the end tip surface is relatively tiny throughout comparison to its overall surface.Reinforced concrete is a raw material that has always been available, but it was unappreciated by architects until the nineteenth century.
a. True
b. False
Answer: False
Explanation:
Reinforced concrete is simply a combination of the traditional cement concrete with the steel bars which are the reinforcements.
Reinforced concrete is utilized for construction purpose mostly on a large scale. The reinforced concrete was invented by French gardener Joseph in 1849 therefore, it has always been available and appreciated by architects before the 19th century.
where are the field poles mounted on an alternator
Answer:
The magnetic field for this type of alternator is established by a set of stationary field poles mounted on the periphery of the alternator frame. The field flux created by these poles is cut by conductors inserted in slots on the surface of the rotating armature.
In an international film festival, a penal of 11 judges is formed to judge the best film. At
last two films FA and FB were considered to be the best where the opinion of judges got
divided. Six judges where in favor of FA whereas five in favor of FB. A random sample
of five judges was drawn from the panel. Find the probability that out of five judges,
three are in favor of film FA.Enunciate demerits of classical probability.
Answer:
International Film Festival
Judging the best best film:
a. The probability that out of five judges (random sample), three are in favor of film FA is:
= 33%.
b. The demerits of classical probability are:
1. Classical probability can only be used with events that have definite numbers of possible outcomes.
2. Classical probability can only handle events where each outcome is equally likely.
3. Classical probability is based on the assumption of linear relationship (which is not always true in real life) between the latent variable and observed scores.
Explanation:
a) Number of judges = 11
Number of judges in favor of FA film = 6
Number of judges in favor of FB film = 5
Probability of judges in favor of FA film = 6/11
Probability of judges in favor of FB film = 5/11
Random sample of judges = 5
Probability that out of five judges, three are in favor of film FA = 3/5 * 6/11
= 18/55
= 33%
b) Classical probability is the simple probability showing that each event has equal chance of happening. It can be contrasted with empirical probability that is obtained from experiments.
Suppose a causal CT LTI system has bilateral Laplace transform H(s) 2s - 2 $2 + (10/3)s + 1 (8)
(a) Write the linear constant coefficient differential equation (LCCDE) relating a general input x(t) to its corresponding output y(t) of the system corresponding to this transfer function in equation (8).
(b) Suppose the input x(t) = e-tu(t). Find the output y(t). In part (c), the output signal can be expressed as y(t) = - e-(1/3)t u(t) + e-tu(t) e-3tu(t), - 019 Where a, b, and care positive integers. What are they? a = b = C=
Solution :
Given :
[tex]$H(S) =\frac{2S-2}{S^2+\left(\frac{10}{3}\right) S+1}$[/tex]
Transfer function, [tex]$H(S) =\frac{Y(S)}{K(S)}= \frac{2S-2}{S^2+\left(\frac{10}{3}\right) S+1}$[/tex]
[tex]$Y(S) \left(S^2+\frac{10}{3}S+1\right) = (2S-2) \times (S)$[/tex]
[tex]$S^2Y(S) + \frac{10}{3}(SY(S)) + Y(S) = 2(S \times (S)) - 2 \times (S)$[/tex]
Apply Inverse Laplace Transforms,
[tex]$\frac{d^2y(t)}{dt^2} + \frac{10}{3} \frac{dy(t)}{dt} + y(t)=2 \frac{dx(t)}{dt} - 2x(t)$[/tex]
The above equation represents the differential equation of transfer function.
Given : [tex]$x(t)=e^{-t} u(t) \Rightarrow X(S) = \frac{1}{S+1}$[/tex]
We have : [tex]$H(S) =\frac{Y(S)}{K(S)}= \frac{2S-2}{S^2+\left(\frac{10}{3}\right) S+1}$[/tex]
[tex]$Y(S) = X(S) \times \frac{6S-6}{3S^2+10 S + 3} = \frac{6S-6}{(S+1)(3S+1)(S+3)}$[/tex]
[tex]$Y(S) = \frac{A}{S+1}+\frac{B}{3S+1} + \frac{C}{S+3}[/tex]
[tex]$A = Lt_{S \to -1} (S+1)Y(S)=\frac{6S-6}{(3S+1)(S+3)} = \frac{-6-6}{(-3+1)(-1+3)} = 3$[/tex]
[tex]$B = Lt_{S \to -1/3} (3S+1)Y(S)=\frac{6S-6}{(S+1)(S+3)} = \frac{-6/3-6}{(1/3+1)(-1/3+3)} = \frac{-9}{2}$[/tex]
[tex]$C = Lt_{S \to -3} (S+3)Y(S)=\frac{6S-6}{(S+1)(3S+1)} = \frac{-18-6}{(-3+1)(-9+1)} = \frac{-3}{2}$[/tex]
So,
[tex]$Y(S) = \frac{3}{S+1} - \frac{9/2}{3S+1} - \frac{3/2}{S+3}$[/tex]
[tex]$=\frac{3}{S+1} - \frac{3/2}{S+1/3} - \frac{3/2}{S+3}$[/tex]
Applying Inverse Laplace Transform,
[tex]$y(t) = 3e^{-t}u(t)-\frac{3}{2}e^{-t/3}u(t) - \frac{3}{2}e^{-3t} u(t)$[/tex]
[tex]$=\frac{-3}{2}e^{-\frac{1}{3}t}u(t) + \frac{3}{1}e^{-t}u(t)-\frac{3}{2}e^{-3t} u(t)$[/tex]
where, a = 2
b = 1
c= 2
A hollow pipe is submerged in a stream of water so that the length of the pipe is parallel to the velocity of the water. If the water speed doubles and the cross-sectional area of the pipe triples, what happens to the volume flow rate of the water passing through it?
Answer:
increases by a factor of 6.
Explanation:
Let us assume that the initial cross sectional area of the pipe is A m² while the initial velocity of the water is V m/s², hence the flow rate of the water is:
Initial flow rate = area * velocity = A * V = AV m³/s
The water speed doubles (2V m/s) and the cross-sectional area of the pipe triples (3A m²), hence the volume flow rate becomes:
Final flow rate = 2V * 3A = 6AV m³/s = 6 * initial flow rate
Hence, the volume flow rate of the water passing through it increases by a factor of 6.
A 1m3 tank containing air at 25℃ and 500kPa is connected through a valve to
another tank containing 5kg of air at 35℃ and 200kPa. Now the valve is opened,
and the entire system is allowed to reach thermal equilibrium, which is at 20℃
(Take: Ru = 8.314 kJ / kg.K).
Answer:
The right answer is "2.2099 m³".
Explanation:
Given:
Mass,
m = 5 kg
Temperature,
T = 35℃
or,
= 35 + 273
Pressure,
P = 200 kPa
Gas constant,
R = 0.2870 kj/kgK
By using the ideal gas equation,
The volume will be:
⇒ [tex]PV=mRT[/tex]
or,
⇒ [tex]V=\frac{mRT}{P}[/tex]
By substituting the values, we get
[tex]=\frac{5(0.2870)(35+273)}{200}[/tex]
[tex]=\frac{441.98}{200}[/tex]
[tex]=2.2099 \ m^3[/tex]
what is the best glide speed for your training airplane
1.5 nautical miles per 1,000 feet
Calculate density, specific weight and weight of one litter of petrol having specific gravity 0.7
Explanation:
mass=19kg
density=800kg/m³
volume=?
as we know that
density=mass/volume
density×volume=mass
volume=mass/density
putting the values
volume=19kg/800kg/m³
so volume=0.02375≈0.02m³
1. A manufacturing cell with two workers is responsible for producing a small frying pan with a required takt time of 496 seconds. The material passes through two processes: a deep drawing process and a trimming process. The average cycle time for the deep drawing process is 450 seconds and average cycle time for trimming is 430 seconds. (2 pts.)
a. Does the work cell have adequate capacity to meet demand? Explain.
b. What is the required daily production capacity of the work cell (in number of frying pans per day)? Assume 480 minutes/workday of available time.
2. What is the total daily idle time for both workers in Problem 1? Report your answer in (a) seconds of idle time and (b) as a percentage of total working time for the cell. (2 pts.)
Answer:
Explanation:
[tex]496=\frac{480\times 60}{demand}[/tex]
demand per day = 58 pans
Due to availability of two workers we can have parallel we can have deep drawing and trimming operations simultaneously.
Hence the cycle time would be the greater time of the two operations.
cycle time = 450 seconds
[tex]\text{capacity of work cell}=\frac{\text{available working time}}{\text{cycle time}}[/tex]
[tex]\text{capacity of work cell}=\frac{480\times 60}{450}[/tex]
[tex]\text{capacity of work cell}=64 ~pans[/tex] (which is greater than the demand of 58 pans)
Therefore the work cell has sufficient capacity and time (496 sec.>cycle time 450 sec) to meet the demand.
b)
Required daily production is 58 pans
A work-mode-choice model is developed from data acquired in the field in order to determine the probabilities of individual travelers selecting various modes. The mode choices include automobile drive-alone (DL), automobile shared-ride (SR), and bus (B). The utility functions are estimated as follows:
UDL = 2.6 - 0.3 (costDL) - 0.02 (travel timeDL)
USR = 0.7 - 0.3 (costSR) - 0.04 (travel timeSR)
UB = -0.3 (costB) - 0.01 (travel timeB)
where cost is in dollars and time is in minutes. The cost of driving an automobile is exist5.50 with a travel time of 21 minutes, while the bus fare is exist1.25 with a travel time of 27 minutes. How many people will use the shared-ride mode from a community of 4500 workers, assuming the shared-ride option always consists of three individuals sharing costs equally?
a. 314
b. 828
c. 866
d. 2805
Answer:
b. 828
Explanation:
UDL = 2.6 - 0.3 [5.5] - 0.02 [ 21 ] = 0.53
USR = 0.7 - 0.3 [5.5 / 2 ] - 0.04 [ 21 ] = -0.69
UB = -0.3 [ 1.25 ] - 0.01 = -0.645
Psr = [tex]\frac{e^{-0.53} }{e^{-0.53} + e^{-0.69} + e^{-0.645} }[/tex]
Solving the equation we get 0.184.
Number of people who will take shared ride is:
0.184 * 4500 = 828 approximately.
A 20-mm-diameter steel bar is to be used as a torsion spring. If the torsional stress in the bar is not to exceed 110 MPa when one end is twisted through an angle of 15°, what must be the length of the bar?
Answer:
1.887 m
Explanation:
(15 *pi)/180
= 0.2618 rad
Polar moment
= Pi*d⁴/32
= (22/7*20⁴)/32
= 15707.96
Torque on shaft
= ((22/7)*20³*110)/16
= 172857.14
= 172.8nm
Shear modulus
G = 79.3
L = Gjθ/T
= 79.3x10⁹x(1.571*10^-8)x0.2618/172.8
= 1.887 m
The length of the bar is therefore 1.887 meters
Using 1.5 V batteries, a switch, and three lamps, devise a circuit to apply 4.5 V across eitherone lamp, two lamps in series, or three lamps in series with a single-control switch. Draw theschematic.
Answer: the attached picture is the answer.
Explanation:
Assuming:
the switch position connect to 1, hence 4.5V exist at across lamp1
the switch position connects to 2 hence 4.5 V exist across lamp 1 and lamp 2
the switch position connects to 3, hence, 4.5 V exist across lamp 1, lamp 2 and lamp 3.
