Answer:
Explanation:
Laser angle with water surface is given by: Tan α = 1/2.0= 0.5/
α = 26.56°
Laser angle with Normal = 90 - 26.56 = 63.44 °
Assuming a red laser, refractive index in water is 1.331.
Angle of refraction in water is given by:
Ref Ind = Sin i / Sin r
1.331 = Sin 63.44 / Sin r
Sin r = 0.8945 / 1.331 = 0.6721
Angle r = 42.22°
For the path in water:
Tan 42.22 = x / 3.2
x = 2.9m where x is the lateral displacement of the laser ince it hits the water
So the goggles are 2.0 + 2.9 = 4.9 m from edge of pool
A 300 MWe (electrical power output) Power Plant having a thermal efficiency of 40% is cooled by sea water. Due to environmental regulations the seawater can only increase temperature by 5 C during the process. How much sea water (minimum) must be used in kg/s for cooling if the plant operates at it's rated capacity?
Answer:
m = 22,877 kg / s
Explanation:
Let's solve this exercise in parts, first look for the amount of heat generated by the plant and then the amount of water to dissipate this heat
The plant generates a power of 300 MW at a rate of 40%, let's use a direct ratio rule to find the heat. If the power is 400 MW it corresponds to 40%, what heat (Q) corresponds to the other 60%
Q = 300 60% / 40%
Q = 450 MW
having the amount of heat generated we can use the calorimeter equation,
Q = m [tex]c_{e}[/tex] [tex](T_{f} - T_{o})[/tex]
m = Q / c_{e} (T_{f} - T_{o})
let's use the maximum temperature change allowed
(T_{f} - T_{o}) = 5
the specific heat of sea water is 3934 J / kg ºC, note that it is less than that of pure water, due to the salts dissolved in sea water
power and energy are related
W = Q / t
Q = W t
let's calculate
m = 450 10⁶ / (3934 5)
m = 22,877 kg / s
A diffraction grating with 200 lines per mm is used in an experiment to study the visible spectrum of a gas discharge tube. At what angle from the beam axis will the first order peak occur if the tube emits light with wavelength of 617.3 nm
Answer
123.5 x 10 ^-3 radian
Explanation:
Given the Width of slit a = 1 x 10⁻³ / 200
a = 5x 10⁻⁶ m .
angle at which first order peak is formed
= λ / a (where λ is wavelength and a is width of slit)
given λ = 617.3 x 10⁻⁹ m
a = 5 x 10⁻⁶
θ = 617.3 x 10⁻⁹ / 5 x 10⁻⁶
= 123.5x 10⁻³ radian .
first order peak is formed at an angle of 123.5 x 10⁻³ radian .
Explanation:
What is an understood decimal
A force of pounds makes an angle of with a second force. The resultant of the two forces makes an angle of to the first force. Find the magnitudes of the second force and of the resultant.
This question is incomplete, the complete question is;
A force of 193 pounds makes an angle of 79°14' with a second force. The resultant of the two forces makes an angle of 27°0' to the first force. Find the magnitudes of the second force and of the resultant.
Answer:
magnitudes of the second force (vector) is 110.84 lb
the resultant force force has a magnitude of 239.85 lb
Explanation:
Given that;
Magnitude of resultant vector R = ?
Direction of resultant vector α = 27°0'
Magnitude of vector p = 193
Magnitude of vector Q = ?
Angle between two vectors ∅ = 79°14'
Using the formula
tan∝ = [ Qsin∅ / P + Qcos∅]
tan27°0' = [ Qsin79°14' / 193 + Qcos79°14' )
we cross multiply
(193tan27°0') + (Qcos79°14'tan27°0' ) = Qsin79°14'
Q = 193tan27°0' / (sin79°14' - cos79°14'tan27°0')
Q = 110.84 lb
Therefore magnitudes of the second force (vector) is 110.84 lb
Now
R = √( p² + Q² + 2PQcos∅ )
R = √( 193² + 110.84² + ( 2 × 193 × 110.84 × cos79°14'))
R = 239.85 lb
Therefore the resultant force force has a magnitude of 239.85 lb
what conventions are used in SI to indicate units
Answer:
Conventions used in SI to indicate units are as follows:
Only singular form of units are used. for example: use kg and not kgs.Do not use full stop after the abbreviations of any unit. for example: do not use kg. or cm.Use one space between last numeric digit and SI unit. for example: 10 cm, 9 km.Symbols and words should not be mixed. for example: use Kilogram per cubic and not kilogram/m3.While writing numerals, only the symbols of the units should be written. for example: use 10 cm and not Ten cm.Units named after a scientist should be written in small letters. for example: newton, henry.Degree sign should not be used when the kelvin unit is used. for exmaple: use 37° and not 37°kIf an electromagnetic wave has components Ey = E0 sin(kx - ωt) and Bz = B0 sin(kx - ωt), in what direction is it traveling?
Answer:
Its traveling in the +x direction
Explanation:
The E-field is in the +y-direction, and the B-field is in the +z-direction, so it must be moving along the +x-direction, since the E-field, B-field and the direction of moving are all at right angles to each other.
The electromagnetic wave is travelling in the +x direction.
Electromagnetic waves are waves formed as a result of vibrations between an electric field and a magnetic field.
Given that:
Ey = E0 sin(kx - ωt)
Hence the electric field is moving in the +y direction.
Also, Bz = B0 sin(kx - ωt)
Hence the magnetic field is moving in the +z direction
Electric fields and magnetic fields (E and B) in an EM wave are perpendicular to each other and are also perpendicular to the direction of propagation of the wave.
Therefore the direction of the wave is travelling in the +x direction.
Find out more at: https://brainly.com/question/25559554
At sea level, at a latitude where , a pendulum that takes 2.00 s for a complete swing back and forth has a length of 0.993 m. What is the value of g in m/s2 at a location where the length of such a pendulum is 0.970 m
Answer:
a) The value of g at such location is:
[tex]g=9.8005171\,\frac{m}{s^2}[/tex]
b) the period of the pendulum with the length is 0.970 m is:
[tex]T=1.9767 sec[/tex]
Explanation:
Recall the relationship between the period (T) of a pendulum and its length (L) when it swings under an acceleration of gravity g:
[tex]L=\frac{g}{4\,\pi^2} \,T^2[/tex]
a) Then, given that we know the period (2.0 seconds), and the pendulum's length (L=0.993 m), we can determine g at that location:
[tex]g=\frac{4\,\pi^2\,L}{T^2}\\g=\frac{4\,\pi^2\,0.993}{(2)^2}\\g=\pi^2\,(0.993)\,\frac{m}{s^2} \\g=9.8005171\,\frac{m}{s^2}[/tex]
b) for this value of g, when the pendulum is shortened to 0.970 m, the period becomes:
For a beam of light in air (n = 1) reflecting off glass (n = 1.5), what is Brewster's angle to the nearest degree?
Answer: 56°
Explanation:
Brewster's angle refers to the angle at the point where light of a certain polarization passes through a transparent dielectric surface and is transmitted perfectly such that no reflection is made.
The formula is;
[tex]= Tan^{-1} (\frac{n_{2} }{n_{1}} )[/tex]
[tex]= Tan^{-1} (\frac{1.5 }{1} )[/tex]
= 56.30993247
= 56°
The concentration of sodium and potassium ions in the blood and body fluid is regulated by :
Answer:
Kidney
Explanation:
One of the main function of the kidney is to maintain the homeostasis of sodium and potassium ions in the blood and body.
Aldosterone is a key steroid hormone that balances sodium and potassium ions in the blood and body fluid. Potassium and sodium ions generate electric impulse in the body which helps to perform different activities such as muscles flexing.
Kidney function for reabsorption and secretion, in which reabsorption of Na is done nd balances the sodium and potassium in the blood and body.
A generator consists of 1000 turns of wire around a coil of area 10cm2 (0.0010m 2 ). Calculate the peak output voltage of this generator when operating at 100 cycles/second in a 0.50 tesla field.
Answer:
The peak output voltage of this generator is 314.2 V.
Explanation:
Given;
the number of turns of the coil, N = 1000 turns
area of the coil, A = 0.001 m²
angular frequency of the coil, f = 100 cycles/seconds
magnitude of the magnetic field, B = 0.5 T
The peak output voltage of this generator is given by;
E = NBAω
Where;
ω is the angular velocity = 2πf
E = NBA(2πf)
E = 1000 x 0.5 x 0.001(2 x π x 100)
E = 314.2 V
Therefore, the peak output voltage of this generator is 314.2 V.
Question 18(Multiple Choice Worth 2 polnis)
When riding your skateboard you crash into a curb, the skateboard stops, and you continue moving forward. Which law of
motion is being described in this scenario?
O Law of Universal Gravitation
o Newton's Second Law of Motion
o Law of Conservation of Energy
o Newton's First Law of Motion
(a) Determine the capacitance of a Teflon-filled parallel-plate capacitor having a plate area of 1.80 cm2 and a plate separation of 0.010 0 mm.
pF
(b) Determine the maximum potential difference that can be applied to a Teflon-filled parallel-plate capacitor having a plate area of 1.80 cm2 and a plate separation of 0.010 0 mm.
kV
Explanation:
(a) Given that,
Area of a parallel plate capacitor, [tex]A=1.8\ cm^2=1.8\times 10^{-4}\ m^2[/tex]
The separation between the plates of a capacitor, [tex]d=0.01\ mm = 10^{-5}\ m[/tex]
The dielectric constant of, k = 2.1
When a dielectric constant is inserted between parallel plate capacitor, the capacitance is given by :
[tex]C=\dfrac{k\epsilon_o A}{d}[/tex]
Putting all the values we get :
[tex]C=\dfrac{2.1\times 8.85\times 10^{-12}\times 1.8\times 10^{-4}}{0.01\times 10^{-3}}\\\\C=3.345\times 10^{-10}\ F\\\\C=334.5\ pF[/tex]
(b) We know that the Teflon has dielectric strength of 60 MV/m, [tex]E=60\times 10^6\ V/m[/tex]
The voltage difference between the plates at this critical voltage is given by :
[tex]V=Ed\\\\V=60\times 10^6\times 0.01\times 10^{-3} \\\\V=600\ V[/tex]
or
V = 0.6 kV
We have that the Capacitance and potential difference is mathematically given as
[tex]Vmax=\frac{Q}{334.68pF}[/tex]C=334.68pF
Capacitance &potential differenceQuestion Parameters:
having a plate area of 1.80 cm2 and a plate separation of 0.010 0 mm
having a plate area of 1.80 cm2 and a plate separation of 0.010 0 mm.
a)
Generally the equation for the Capacitance is mathematically given as
[tex]C=\frac{ke_0A}{d}\\\\Therefore\\\\C=\frac{2.1*1.80e-4*8.85e12}{0.01e-3}\\\\[/tex]
C=334.68pF
b)
Generally the equation for the Capacitance is mathematically given as
[tex]Vmax=\frac{Q}{C}[/tex]
Where
Q is the charge on the plates, and hence not given
Therefore, maximum potential difference is
[tex]Vmax=\frac{Q}{334.68pF}[/tex]
For more information on potential difference visit
https://brainly.com/question/14883923
¿Cómo podrías utilizar el sistema de posicionamiento global para proponer recorridos alternativos para llegar a un lugar específico (centro educativo, supermercado, el hogar, el parque, entre otros)?
Answer:
El sistema de posicionamiento global (conocido mundialmente como GPS) podría utilizarse para proponer recorridos alternativos para llegar a un lugar específico, como un parque, a través de la creación de un recorrido guiado por una aplicación móvil con diferentes rutas de acceso al lugar.
Así, por ejemplo, se crearían diferentes rutas de acceso desde un punto A hasta un punto B, teniendo en cuenta factores como: rapidez, congestión vehicular, pago o no de peajes, posibilidad de acceso a pie y determinados factores extra que influyan en la forma de llegar al lugar. Todo ello plasmado en un mapa interactivo en el cual se señalen las rutas disponibles mediante el marcado del mapa en cuestión.
If the solenoid is 45.0 cm long and each winding has a radius of 8.0 cm , how many windings are in the solenoid
Answer:
The number of windings is 1.
Explanation:
The radius of the solenoid = 8.0 cm = 0.08 m
Length of the solenoid = 45.0 cm = 0.45 m
number of turn = ?
circumference of each winding = 2πr = 2 x 3.142 x 0.08 = 0.503 m
The number of windings = (Length of the solenoid)/(circumference of each winding)
==> 0.45/0.503 = 0.89 ≅ 1
Atoms are the particles that all matter is made from. When two or more kinds of atoms combine, they form _______. A. pure elements B. molecules C. metals D. the periodic table
Answer:
Atoms are the particles that all matter is made from. When two or more kinds of atoms combine, they form pure elements
The answer is option A
Answer:
its molecues
Explanation:
Just wondering if I did this right
Yeah
All they are all correct
?a wire is stretched 30% what is the percentage change in resistance
Answer:
The percentage change in resistance of the wire is 69%.
Explanation:
Resistance of a wire can be determined by,
R = (ρl) ÷ A
Where R is its resistance, l is the length of the wire, A its cross sectional area and ρ its resistivity.
When the wire is stretched, its length and area changes but its volume and resistivity remains constant.
[tex]l_{o}[/tex] = 1.3l, and [tex]A_{o}[/tex] = [tex]\frac{A}{1.3}[/tex]
So that;
[tex]R_{o}[/tex] = (ρ[tex]l_{o}[/tex]) ÷ [tex]A_{o}[/tex] = (ρ × 1.3l) ÷ ([tex]\frac{A}{1.3}[/tex])
= (1.3lρ) ÷ ([tex]\frac{A}{1.3}[/tex])
= [tex](1.3)^{2}[/tex] × [(ρl) ÷ A]
= 1.69R (∵ R = (ρl) ÷ A)
[tex]R_{o}[/tex] = 1.69R
Where [tex]R_{o}[/tex] is the new resistance, [tex]l_{o}[/tex] is the new length, and [tex]A_{o}[/tex] is the new area after stretching the wire.
The change in resistance of the wire = [tex]R_{o}[/tex] - R
= 1.69R - 1R
= 0.69R
The percentage change in resistance = [tex]\frac{0.69R}{R}[/tex] × 100
= 0.69 × 100
= 69%
The percentage change in resistance of the wire is 69%.
Two spheres A and B of negligible dimensions and masses 1 kg and √3 kg respectively, are supported on the smooth circular surface, fixed to the ground with a centre O and radius of 0.1m. The spheres are joined by the cord shown in length π/20 m; determine the angles α and β corresponding to the position of equilibrium of the spheres with respect to the vertical passing through O.
Answer:
α = π/3
β = π/6
Explanation:
Use arc length equation to find the sum of the angles.
s = rθ
π/20 m = (0.1 m) (α + β)
π/2 = α + β
Draw a free body diagram for each sphere. Both spheres have three forces acting on them:
Weight force mg pulling down,
Normal force N pushing perpendicular to the surface,
and tension force T pulling tangential to the surface.
Sum of forces on A in the tangential direction:
∑F = ma
T − m₁g sin α = 0
T = m₁g sin α
Sum of forces on B in the tangential direction:
∑F = ma
T − m₂g sin β = 0
T = m₂g sin β
Substituting:
m₁g sin α = m₂g sin β
m₁ sin α = m₂ sin β
(1 kg) sin α = (√3 kg) sin (π/2 − α)
1 sin α = √3 cos α
tan α = √3
α = π/3
β = π/6
How much work is needed to pump all the water out of a cylindrical tank with a height of 10 m and a radius of 5 m
Answer:
Explanation:
volume of water being lifted
= π r² h , where r is radius of cylinder and h is height of cylinder
= 3.14 x5² x 10
= 785 m³
mass of water = 785 x 10³ kg
mass of this much of water is lifted so that its centre of mass is lifted by height
10 / 2 = 5m .
So work done = mgh , m is mass of water , h is displacement of centre of mass and g is acceleration due to gravity
= 785 x 10³ x 9.8 x 5
= 38.465 x 10⁶ J
A spherical balloon has a radius of 6.95 m and is filled with helium. The density of helium is 0.179 kg/m3, and the density of air is 1.29 kg/m3. The skin and structure of the balloon has a mass of 950 kg. Neglect the buoyant force on the cargo volume itself. Determine the largest mass of cargo the balloon can lift. Express your answer to two significant figures and include the appropriate units.
volume of balloon
= 4/3 T R3
= 4/3 x 3.14 x 6.953
= 1405.47 m3
uplift force
= volume of balloon x density of air x 9.8
= = 1405.47 x 1.29 x 9.8
= 1813.05 x 9.8 N
weight of helium gas
= volume of balloon x density of helium x
9.8
= 1405.47 x .179 x 9.8
= 251.58 x 9.8 N
Weight of other mass = 930 x 9.8 N Total weight acting downwards
= 251.58 x 9.8 +930 x 9.8
= 1181.58 x 9.8 N
If W be extra weight the uplift can balance
1181.58 × 9.8 + W × 9.8 = 1813.05 * 9.8
1181.58+W=1813.05
W= 631.47 kg
An interference pattern is produced by light with a wavelength 520 nm from a distant source incident on two identical parallel slits separated by a distance (between centers) of 0.440 mm.
1. If the slits are very narrow, what would be the angular position of the first-order, two-slit, interference maxima?
2. What would be the angular position of the second-order, two-slit, interference maxima in this case?
3. Let the slits have a width 0.310 mm . In terms of the intensity I0 at the center of the central maximum, what is the intensity at the angular position of θ1?
4. What is the intensity at the angular position of θ2?
Answer:
1) θ = 0.00118 rad, 2) θ = 0.00236 rad , 3) I / I₀ = 0.1738, 4) I / Io = 0.216
Explanation:
In the double-slit interference phenomenon it is explained for constructive interference by the equation
d sin θ = m λ
1) the first order maximum occurs for m = 1
sin θ = λ / d
θ = sin⁻¹ λ / d
let's reduce the magnitudes to the SI system
λ = 520 nm = 520 10⁻⁹ θ = 0.00118 radm
d = 0.440 mm = 0.440 10⁻³ m ³
let's calculate
θ = sin⁻¹ (520 10⁻⁹ / 0.44 10⁻³)
θ = sin⁻¹ (1.18 10⁻³)
θ = 0.00118 rad
2) the second order maximum occurs for m = 2
θ = sin⁻¹ (m λ / d)
θ = sin⁻¹ (2 5¹20 10⁻⁹ / 0.44 10⁻³)
θ = 0.00236 rad
3) To calculate the intensity of the interference spectrum, the diffraction phenomenon must be included, so the equation remains
I = I₀ cos² (π d sin θ /λ ) sinc² (pi b sin θ /λ )
where the function sinc = sin x / x
and b is the width of the slits
we caption the values
x = π 0.310 10⁻³ sin 0.00118 / 520 10⁻⁹)
x = 2.21
I / I₀ = cos² (π 0.44 10⁻³ sin 0.00118 / 520 10⁻⁹) (sin (2.21) /2.21)²
remember angles are in radians
I / I₀ = cos² (3.0945) [0.363] 2
I / I₀ = 0.9978 0.1318
I / I₀ = 0.1738
4) the maximum second intensity is
I / I₀ = cos² (π d sinθ / λ) sinc² (πb sin θ /λ)
x =π 0.310 10⁻³ sin 0.00236 / 520 10⁻⁹)
x = 4.41
I / Io = cos² (π 0.44 10⁻³ sin 0.00236 / 520 10⁻⁹) (sin 4.41 / 4.41)²
I / Io = cos² 6.273 0.216
I / Io = 0.216
.
Why was Bohr's atomic model replaced by the
modern atomic model?
Answer:
Explanation:
Bohr's atomic model was replaced by the modern atomic model because of its limitations, which included :
(a) Only applicable for Hydrogen and like atoms ( He+1, Li+2 )
(b) Couldn't explain Zeeman Effect (splitting of spectral lines due external magnetic field ) and Stark Effect (splitting of spectral lines due to external electric field).
(c) Inconsistent with De-Broglie's Dual nature of matter and Heisenberg Uncertainty principal, etc.
A defibrillator is a device used to shock the heart back to normal beat patterns. To do this, it discharges a 15 μF capacitor through paddles placed on the skin, causing charge to flow through the heart. Assume that the capacitor is originally charged with 5.0 kV .Part AWhat is the charge initially stored on the capacitor?3×10−9 C7.5×104 C7.5×10−2 C7.5×10−5 CPart BWhat is the energy stored on the capacitor?What is the energy stored on the capacitor?1.9×108 J380 J190 J1.9×10−4 JPart CIf the resistance between the two paddles is 100 Ω when the paddles are placed on the skin of the patient, how much current ideally flows through the patient when the capacitor starts to discharge?5×105 A50 A2×10−2 A5×10−2 APart DIf a defibrillator passes 17 A of current through a person in 90 μs . During this time, how much charge moves through the patient?If a defibrillator passes 17 {\rm A} of current through a person in 90 {\rm \mu s} . During this time, how much charge moves through the patient?190 mC1.5 C1.5 mC17 C
Answer:
a) q = 7.5 10⁻² C , b) 190 J , c) I₀ = 50 A , d) 1.5 mC
Explanation:
The expression for capacitance is
C = q / DV
q = C DV
let's reduce the magnitudes to the SI system
ΔV = 5 kV = 5000 V
C = 15 μF = 15 10⁻⁶ F
t = 90 μs = 90 10⁻⁶ s
q = 15 10⁻⁶ 5000
q = 7.5 10⁻² C
b) the energy in a capacitor is
U = ½ C ΔV²
U = ½ 15 10⁻⁶ 5000²
U = 1,875 10² J
answer 190 J
c) At the moment the discharge begins, all the current is available and it decreases with time,
whereby
V = I R
in the first instant I = Io
I₀ = V / R
I₀ = 5000/100
I₀ = 50 A
but this is for a very short time
answer 50 A
d) The definition of current is
i = dq / dt
in this case they give us the total current and the total time, so we can find the total charge
i = q / t
q = i t
q = 17 90 10⁻⁶
q = 1.53 10⁻³ C
answer is 1.5 mC
Two narrow slits are illuminated by a laser with a wavelength of 593 nm. The interference pattern on a screen located x = 4.80 m away shows that the fourth-order bright fringe is located y = 8.20 cm away from the central bright fringe. Calculate the distance between the two slits.
Answer:
The distance is [tex]d = 1.39 *10^{-4} \ m[/tex]
Explanation:
From the question we are told that
The wavelength is [tex]\lambda = 593 \ nm = 593 *10^{-9} \ m[/tex]
The distance of the screen is x = 4.80 m
The location of the fourth order bright fringe is y = 8.20 cm = 0.082 m
The order of the fringe is n = 4
Generally the position of a fringe with respect to the central fringe is mathematically represented as
[tex]y = \frac{ n * x * \lambda }{d}[/tex]
Where d is the distance between the slits, so making d the subject
[tex]d = \frac{\lambda * x * n }{ y }[/tex]
substituting values
[tex]d = \frac{ 593 *10^{-9} * 4.80 * 4 }{ 0.082 }[/tex]
[tex]d = 1.39 *10^{-4} \ m[/tex]
A 1.5 V battery is connected to a 1000 ohm resistor and a 500 ohm resistor in series. The voltage across the 1000 ohm resistor is _____ V.
Answer:
1 volt and 0.5 voltExplanation:
Given data
voltage supplied Vs= 1.5 volts
resistance R1= 1000 ohms
resistance R2= 500 ohms
The total resistance is
Rt= 1000+ 500
Rt= 1500 ohms
The current I is given as
[tex]I= \frac{Vs}{Rt} \\\\ I= \frac{1.5}{1500} = 0.001mA[/tex]
Voltage across R1
[tex]VR1= Vs(\frac{R1}{R1+R2} )=1.5(\frac{1000}{1000+500} )= 1.5(\frac{1000}{1500} )\\ \\\ VR1= 1v[/tex]
Voltage across R2
[tex]VR2= Vs(\frac{R2}{R1+R2} )=1.5(\frac{500}{1000+500} )= 1.5(\frac{500}{1500} ) \\\ VR2=0.5v[/tex]
In series connection the current is the same for all components while the voltage divides across all components,the voltages consumed by each individual resistance is equal to the source voltage.
Please help!
Much appreciated!
Answer:
your question answer is 22°
A bicycle has wheels that are 60 cm in diameter. What is the angular speed of these wheels when it is moving at 4.0 m/s
Answer:
13.33 rad/s
Explanation:
Applying,
v = ωr......................... Equation 1
Where v = linear speed, ω = angular speed and r = radius.
Note that,
r = d/2................. Equation 2
Where d = diameter of the wheel.
Substitute equation 2 into equation 1
v = ωd/2............... Equation 3
make ω the subject of the equation
ω = 2v/d................ Equation 4
Given: v = 4 m/s, d = 60 cm = 0.6 m
Substitute these values into equation 4
ω = 2(4)/0.6
ω = 13.33 rad/s
Bob and Lily are riding on a merry-go-round. Bob rides on a horse near the outer edge of the circular platform, and Lily rides on a horse near the center of the circular platform. When the merry-go-round is rotating at a constant angular speed, Bob's angular speed is:_____.
a. the same as Lily's.
b. larger than Lily's.
c. exactly half as much as Lily's.
d. exactly twice as much as Lily's.
e. smaller than Lily's.
Answer: the same as Lily's
Explanation:
Angular velocity has to do with the speed at which an object will be able to rotate. We are informed that Bob and Lily are riding on a merry-go-round.
Since we are further told that Bob rides on a horse near the outer edge of the circular platform, and Lily rides on a horse near the center of the circular platform and that he merry-go-round is rotating at a constant angular speed.
Based on the above analysis, Bob's angular speed will be thesame as that of Lily.
PLEASE HELP FAST WILL GIVE BRAINLIEST The sentence, "The popcorn kernels popped twice as fast as the last batch," is a(n) _____. 1.experiment 2.hypothesis 3.observation 4.control
The answer is 3. Observation
Explanation:
The sentence "The popcorn kernels popped twice as fast as the last batch" is the result of observing or measuring the time popcorn kernels require to pop. In this context, the sentence best matches the word "observation" which the term used in the Scientific method to refer to statements that are the result of studying a phenomenon, either through the senses such as sight or through precise instruments that allow scientists to understand numerically variables such as time, speed, temperature, etc.
a ball is kicked on level ground with a speed of 30 m/s at angle of 40 degrees above horizontal g Find the minimum velocity of the ball during its flight
Answer:
The minimum velocity of the ball during its flight is 22.98 m/s.
Explanation:
The velocity of the ball v = 30 m/s
The angle it makes with the horizontal ∅ = 40°
The minimum velocity of the ball during flight will be the horizontal axis component of the velocity, as acceleration is zero on this axis.
[tex]V_{x}[/tex] = v cos ∅
[tex]V_{x}[/tex] = 30 cos 40°
[tex]V_{x}[/tex] = 30 x 0.766 = 22.98 m/s
