Answer:
No, work isn't being done by Johnny.
Explanation:
Work can be defined as the energy transferred to a physical object by exertion of a force on the object to cause a displacement of the object. Thus, work is typically done when a person or simple machine move an object over a distance through the application of a force.
Mathematically, work done is given by the formula;
Work done = force * distance
[tex] W = F * d[/tex]
Where,
W is the work done
F represents the force acting on a body.
d represents the distance covered by the body.
In this scenario, Johnny's push didn't cause a displacement of the wall and as such no work is done.
Find the force due to a current element of length 6cm and flux density of 12 tesla. The current through the element will be 10A.
Answer:
7.2 N
Explanation:
Applying,
F = BIL................. Equation 1
Where F = Force due to current through the element, B = magnetic field, L = Length of the element.
From the question,
Given: B = 12 Tesla, L = 6 cm = 0.06 m, I = 10 A
Substitute these values into equation 1
F = 12(0.06)(10)
F = 7.2 N
Hence the force through the element is 7.2 N
What is the purpose of the circuit breaker in your home?
To provide electricity to all of the electrical devices in your home.
To maximize the electrical efficiency of appliances plugged in.
To prevent too much current from traveling into the circuit, making the wire hot and starting a fire.
To irritate the %$&* out of you when they turn off.
Answer:
to prevent to much current
Explanation:
in the event of a power surge the circuit breaker will cut the power. this is what people mean when they say "pop" the breaker
A 91.5 kg football player running
east at 2.73 m/s tackles a 63.5 kg
player running west at 3.09 m/s.
What is their velocity afterward?
Answer:
I'm pretty sure the velocity is 2.88 m/s
Explanation:
hope this is right good luck
Answer:
0.348
Explanation:
Acellus
A _____ is a model of an atom in which each dot represents a valence electron
Answer:
electron dot diagram is the answer to your question.
1. 10. waves break on the beach in 2.0 min. What is the frequency in hertz of these waves (cycles per
second)? What is the time between successive waves, in seconds?
Answer:
there it is fella tried o. ma own consciousness
An object falling straight down without air resistance is said to be exhibiting
A. free fall
B. projectile motion
C. circular motion
D. two-dimensional motion
Answer:
Explanation:
If the object is falling straight down it is in free fall. The difference between that and two-dimensional motion is that 2D motion is parabolic (projectile)
6. A ball rolled 125 m from the top of a hill to the bottom of a hill. How long
did it take for the ball to roll if the average velocity was 5m/s? *
suggest and explain the modifications that need to be done on the galvanometer to increase its sensitivity.
Answer:
So, sensitivity of the galvanometer can be increased either by increasing the number of turns (N), using strong magnets or increasing the area of the coil (A). So, the correct answer is that the sensitivity of a moving coil galvanometer can be increased by increasing the number of turns of the coil.
man start to moves from point A (Initial Point) to Point B (Final Point) in a given
figure. Find the Distance and Displacement from the given Figure :-
(2)
Answer:
Image not full.
Explanation:
From what I can see, Displacement is 175m,
Distance will be = 100 + 50 + the hidden value on the bottom right
Answer this question fast please
Why are circuit breakers and fuses important?
1)They help regulate the voltage drop in a power source.
2)They help insulate live wires to prevent shocks.
3)They help prevent electrical accidents.
4)They help current flow smoothly.
Answer:
option 3, as circuit breakers are mostly used as precautions
I need help with this science question, 50 points!
Answer:
an open circuit (A battery, bulb, wire,switch)
Explanation:
the battery supplies the power the wire carries the current from the battery to the bulb but the circuit is not completed if the switch is not connected (Switch )
A CAR APPROACHING A SCHOOL ZONE SLOWS DOWN FROM 38 M/S TO 10 M/S AT A CONSTANT ACCELERATION -4 METER PER SEC SQUARE HOW MUCH TIME IS REQUIRED TO SLOW DOWN TO FINAL VELOCITY
Answer:
7 seconds
Explanation:
he went down -28 m/s so 7 times -4 equals -28 m/s which is what he needed to slowness down to 10 m/s
Having greater or less electrons possessed by an object. Can attract or repel.
A. proton
B. magnetism
C. charge
D.magnet
Answer:
A. Proton
Explanation:
Given that an electron has a net negative charge equal in magnitude to the charge of a proton (1.602 × 10⁻¹⁹) but having an opposite (negative) sign to that of a proton, and given that like charges (negative to negative) repel and unlike charges attract, an object having;
Greater electron will be negatively charged relative to the other object, to which it is compare, which is a proton will attract the (positively charged) proton
Lesser negative charge compared to the proton; therefore, both objects will be positive, and they will repel each other
We therefore have;
Having greater or less electrons possessed by an object. Can attract or repel a proton
The correct option is option A. proton
A hippopotamus laying on the rock exerts 10,000 N on the rock. The rock has a mass of
2 tons. How much work is being done? Be sure to show your work.
Answer:
Explanation:
If the hippo is laying on the rock, I'm assuming that there is no movement going on at all, in either the hippo or the rock. If no movement occurs, there is no work being done.
is James Charles a boy or a girl ? I am so confused
Answer:
both
Explanation:
and I'm serious he is literally both
Ponds and lakes are part of marine ecosystem.
True or false ?
Answer:
True
Explanation:
because they can hold marine organism inside
A riddle for you
In some situations, I oppose the motion
in other situations, I facilitate the motion
but, I always oppose
the relative motion
between two moving surfaces.
Put some lubricant, and
I become small there.
Make the moving surfaces rough
I make the movement tough.
I may be
static, sliding or rolling
but whenever two surfaces are in motion
I am always there,
Tell me who I am!
The person who answers it correctly will be marked as brainlist
Answer:
The Answer is FRICTION!
True or False. Friction is a non-contact force?
( please answer !! i’ll mark brainliest! )
Answer:
False
Explanation:
Friction is a force exerted by a surface against the motion of a body across its surface. Therefore, friction is a type of contact force only.
why does pressure on Diver increases with depth?
Answer: the pressure increases with the amount of water pushing in on all sides of the diver, for example, when you jump into a pool and you head is above water it a little harder to breathe, it is the same way for divers when they are diving at increasingly deep depths, the deeper you are the more water is pressing in on you.
Explanation:
An electrical heating coil is immersed in 4.6kg of water 22°C.The coil, which has a resistance of 250Ω, warms the water to 32°C in 15min. What is the potential difference at which the coil operates?
Answer:
242.4 V
Explanation:
Applying,
Q = cm(t₂-t₁)................ Equation 1
Where Q = amount of heat, c = specific heat capacity, m = mass, t₁ = initial temperature, t₂ = final temperature.
But this heat is produced by electrical power
Therefore,
P = Q/t
Where P = Electrical power, t = time
Also,
P = V²/R
Where V = voltage, R = resistance
Therefore
V²/R = Q/t......................... Equation 2
Substitute equation 1 into equation 2
V²/R = cm(t₂-t₁)/t................. Equation 3
Given: R = 250 ohms, m = 4.6 kg, t₁ = 22°C, t₂ = 32°C, t = 15 min. = (15×60) = 900 seconds
Constant: c = 4600 J/kg.°C
Substitute these values into equation 2
V²/250 = 4600(4.6)(32-22)/900
V²/250 = 235.11
V² = 250×235.11
V² = 58777.78
V = √58777.78
V = 242.4 V
A person walks at a speed of 6 km/h from point A to point B. If he improves his pace by 1.5 km/h, he will arrive 1 hour earlier.
a) calculate the distance and time he intends to travel from a to b
b) the individual initially travels at v1=6 km/h for a distance s1, then pauses for 15 minutes to rest. So he goes at v2=7.5km/h for the rest of the route and arrives 30 minutes early than expected.
Answer:
a) The distance is 30 km
The time duration is 5 hours
b) s₁ is approximately 28.142 km or s₁ is approximately 1.505 km
Explanation:
The initial speed with of the person, v₁ = 6 km/h
The distance the walked by the person, d = From point A to point B
The rate at which the person increases the speed, Δv = 1.5 km/h
The time it takes for the person to arrive at point B from point A at the new speed, t₂ = 1 hour earlier than when walking at 6 km/h
a) Let t₁ represent the time it takes the person walking from point A to point B at 6 km/h, we have;
t₂ = t₁ - 1...(1)
d/t₁ = 6...(2)
d/t₂ = 6 + 1.5 = 7.5
∴ d/t₂ = 7.5...(3)
From equation (2), we have;
d = 6 × t₁ = 6·t₁
Plugging in d = 6·t₁, and t₂ = t₁ - 1 in equation (3) gives;
d/t₂ = 7.5
∴ 6·t₁/t₁ - 1 = 7.5
6·t₁ = 7.5 × (t₁ - 1) = 7.5·t₁ - 7.5
7.5·t₁ - 6·t₁ = 7.5
1.5·t₁ = 7.5
t₁ = 7.5/1.5 = 5
t₁ = 5
The time it takes the person walking from point A to point B at 6 km/h, t₁ = 5 hours
The distance from point A to point B, d = 6 km/h × 5 hours = 30 km
b) The distance the person travels at the initial speed, v₁ (6 km/h) = s₁
The duration the person pauses for a rest = 15 minutes = 1/4 hours
The speed with which he walks the rest of the journey, v₂ = 7.5 km/h
The time earlier than expected that he arrives, Δt = 30 minutes = 0.5 hours
We note that the total distance, d = 30 km
The expected time, t₁ = 5 hours
Therefore, we have;
s₁ + s₂ = 30 km
s₂ = 30 - s₁
v₁/s₁ + 1/4 + v₂/s₂ = t₁ - 0.5
Therefore;
6/s₁ + 1/4 + 7.5/(30 - s₁) = 5 - 0.5 = 4.5
6/28.142+ 1/4 + 7.5/(30 - 28.142) = 5 - 0.5 = 4.5
6/s₁ + 7.5/(30 - s₁) = 4.5 - 1/4 = 4.25
-(3·s₁ + 360)/(2·s₁²- 60·s₁) = 4.25
2·s₁²- 60·s₁) × 4.25 + 3·s₁ + 360 = 0
17·s₁²- 504·s₁ + 720 = 0
s₁ = (504 ± √((-504)² - 4 × 17 × 720))/(2 × 17)
s₁ ≈ 28.142 or s₁ = 1.505
The distance the individual travels at v₁ = 6 km/h, s₁ ≈ 28.142 km or 1.505 km
Select all the correct answers. Which statements about potential energy are true?
Answer: The statement gaining potential energy is always associated with a force field, is true about potential energy.
Explanation:
The energy acquired by an object due to its position is called potential energy.
Basically, a force field exerts a force that gives rise to potential energy of an object. For example, gravity, spring force etc.
This means that gaining potential energy is always associated with a force field.
A change in position does not always means that an object gains potential energy. For example, a spring will have more potential energy when it is compressed or stretched.
Hence, change in position of an object not necessarily means always gain in potential energy.
There are two types of potential energy that is, gravitational potential energy and elastic potential energy.
Thus, we can conclude that the statement gaining potential energy is always associated with a force field, is true about potential energy.
Answer:
Explanation:
The first one and the last one are the correct answer.
PLS HELP DUE TODAY
A group of Ontario farmers form a cooperative group and build a factory that turns corn into a fuel for generators and cars. Would this energy source be renewable or non-renewable? Explain.
Answer:
renewable, you can keep growing corn for it. more fossil fuel can be made by nature but it takes way too long to be considered renewable
I need help pleaseee
Answer:
a refraction
b reflection
creflection
d refraction
brainliest plzz
HELP PLEASE 15 POINTS !!!
how big is omniverse?
Answer:
big half like whale is so big
The process of making alloys involves
Answer:
The process of making alloys involves ( Heating ) pure metals to remove impurities. Then the pure metals are(mixed) with other components. An alloy is a mixture of metals or a mixture of a metal and another element. Alloys are defined by a metallic bonding character.
Explanation:
A scientist is examining an unknown solid. Which procedure would most likely help determine a chemical property of the substance?
heating it to find the temperature at which it melts
exposing it to a flame to see if it catches on fire
hitting it with a hammer to determine if it breaks or bends
placing it in water to find out whether or not it dissolves
Answer:
hitting it with a hammer to determine if it breaks or bends
Answer:
exposing it to a flame to see if it catches on fire
Explanation:
A chemical property is when the matter changes into a different substance. This is true when you expose it to a flame because if a substance is burned, it will change into a new substance. All the other options are examples of physical changes.
-I also took the quiz and got 100%
Hope this helps!
in what state of matter can conduction occur.
Answer: Conduction occurs more readily in solids and liquids, where the particles are closer to together, than in gases, where particles are further apart.
Answer:
conduction occurs when gas becomes liquid.
